Used Müller-Mitteltal Etü Trailers for sale (242)

Condition: used, maximum load weight: 26,600 kg, overall weight: 35,000 kg, axle configuration: 3 axles, first registration: 06/2004, next inspection (TÜV): 08/2025, loading space length: 12,600 mm, loading space width: 2,500 mm, loading space height: 900 mm, total width: 2,520 mm, Müller Mitteltal 3 axle semi-trailer low loader Fjdpswtlkhjfx Afmjpp Total weight: 35,000kg technically 41,000 kg Empty weight: 8,400kg Payload: 26,600kg technically 32,600 kg Total length: 13,700mm Loading length: total 12,600mm, gooseneck approx. 2,700mm/ roller slope approx. 1,400mm/ low bed approx. 8,500mm Width: 2,520mm Loading height: approx. 900mm Further information - Side walls gooseneck foldable - Tool box at the front 600mm - Spare wheel bulkhead - Last axle with caster steering - Air suspension - Split long ramps (2,300mm + 1,500mm), hydraulic. Side shift - BPW axles - Warning signs front + rear - Roller slope/gooseneck slope Other new and used low loader semi-trailers available. More information at

Condition: used, maximum load weight: 13,470 kg, overall weight: 18,000 kg, axle configuration: 2 axles, first registration: 06/2024, next inspection (TÜV): 06/2025, loading space length: 7,075 mm, total width: 2,550 mm, total height: 1,150 mm, Year of construction: 2023, Equipment: ABS, Immediately available stock vehicle with daily registration in 07/2024 Fpjdpfxjugzqtj Afmop ABS, EBS-E, RSS, 2x 10 ton axles (Gigant), steel rims, tires 235/75 R17.5, drum brake, automatic slack adjuster, air suspension, lifting + lowering function, WABCO SmartBoard, weight detection / axle load display via EBS-Canbus signal for display on display in the driver's cab (truck must be prepared accordingly, no calibrated scale), release valve on the front axle, spring brake on the rear axle, two pairs of pneumatic container locks for roll-off containers, storage box made of galvanized sheet steel approx.: 1,000x300x600mm, storage box for container net approx.: 1,000x300x600mm, side protection device closed, underrun protection fixed, rear apron on the underrun protection, A-shield foldable, Ramp compartment including aluminum ramps (2,800 mm, long 470 mm wide, approx. 10,600 kg load capacity/pair), hot-dip galvanized chassis, modular lights, some LED, 2 additional LED reversing lights at the rear of the vehicle. La-Si package: 8 pieces of UVV fall lashing brackets (LC 8,000 daN) mounted to the existing hole pattern in the outer frame (protruding by the material thickness) ? Arrangement: 1 pair in front of the rear carrier / 3 pairs in the flat loading area, 1 pair of folding lashing eyes (LC 13,500 daN) on the front wall carrier, 3 pairs of folding lashing eyes (LC 10,000 daN) recessed in the outer frame, 8 interchangeable trough stops for lateral centering of the tipping troughs, 4 front trough stops plugged in with a swinging stop. Duomatic coupling head / 15-pin power supply Drawbar 2,100 mm plus 500 mm lowering device / 40 mm DIN towing eye Truck coupling height: approx. 780-980 mm Container length: 5,500 mm - 7,000 mm i.Li. or 2x 10 cbm ASK troughs or construction machine transport Height: approx. 950 mm with unloaded vehicle (centering edge 970 mm) 20,000 kg GG technically possible Hüffermann Krandienst GmbH: we trade, we rent, we repair. Roll-off trailers, roll-off tippers, garbage collection vehicles, mobile cranes and work platforms... Talk to us! Do you need financing? We would be happy to provide you with a non-binding financing offer. The offer is subject to change, without warranty or guarantee. Subject to prior sale. A deposit of 10% of the purchase price is required for a reservation. Until the money is received, there is no reservation or claim to availability. The purchase is only finalized when payment is received. The vehicle remains the property of Hüffermann Krandienst GmbH until full payment is made. Payments are only accepted in euros at no additional cost to the seller and only by bank transfer or cash. No checks.

Condition: used, empty load weight: 3,450 kg, maximum load weight: 14,550 kg, overall weight: 18,000 kg, axle configuration: 2 axles, first registration: 05/2010, next inspection (TÜV): 07/2025, suspension: air, tire size: 235/75R17.5, color: yellow, mileage: 1,001 km, gearing type: other, driver cabin: other, Equipment: ABS, Vehicle location: Bovenden, 2 axles, turntable trailer, air suspension, ABS (anti-lock braking system), container lock, underride protection, side aluminum side guard, twin tires. Body: 2-axle outside-roller trailer for roll-off containers from 5.5 m to 7 m or 2 x 10 m³ skip containers; BPW axles, drum brakes, pneumatic locking, pneumatic drawbar lowering. ACCESSORY SPECIFICATIONS WITHOUT GUARANTEE, subject to change, prior sale, and errors excepted! Fodpfx Aewypl Nefmopp

Condition: used, maximum load weight: 25,230 kg, overall weight: 32,000 kg, axle configuration: 2 axles, first registration: 06/2012, Equipment: ABS, Müller Mitteltal 2-axle concrete semi-trailer type SF32 BM/BT Body type: HTM 1004 Liebherr 10 m³ from year of construction 2012, BPW axles, drum brakes, air suspension, lift axle, underride guard, EBS, ABS 1st hand inspection book Fpodperdt H Ejfx Afmjp Permissible total weight: 32000 KG Unladen weight: 6770 KG

Condition: new, maximum load weight: 14,650 kg, overall weight: 18,000 kg, axle configuration: 2 axles, Year of construction: 2024, * RS-T 18.0 / 018: * Wabco EBS-E (electronic braking system) * RDÜ tire pressure monitoring * Emergency release device for spring-loaded cylinders * Disc brakes * Duomatic brake connection * 2 x 10 ton SAF axles * Air suspension with automatic lowering when the brake is uncoupled * Pull scissors 2,300 mm long with 40 mm towing eye and height adjustment via tension spring & spindle * Plastic tool box on the right side, closed. Plastic fenders * closed side impact protection as advertising space * underrun protection with 2 impact buffers * foldable A-sign at the rear for waste disposal * LED tail lights with protective roof * 2 x 7-pin power plugs * hot-dip galvanized chassis (without air tank, axles, pull scissors, etc.) * roller track length approx. 6,950 mm * roller container is clamped by pneumatic 4-way claw locking * there are 2 plug-in container stops at the front with 2 additional plug-in positions * driving height unloaded approx. 1,165 mm * -- permissible total weight of 20,000 kg technically possible-- Fpodpol Tqkwofx Afmsp * suitable for 5,000 - 7,000 mm container lengths * new vehicle with manufacturer's warranty * errors and prior sale subject to reservation * available immediately from Egestorf

Condition: used, maximum load weight: 18,610 kg, overall weight: 24,000 kg, axle configuration: 3 axles, first registration: 06/2024, next inspection (TÜV): 06/2025, loading space length: 7,075 mm, total width: 2,550 mm, total height: 1,150 mm, Year of construction: 2023, Equipment: ABS, Immediately available stock vehicle with daily registration in 07/2024 Fedpeugzqyofx Afmepp ABS, EBS-E, RSS, 3x 9 ton axles (Gigant), steel rims, tires 235/75 R17.5, drum brake, automatic slack adjuster, air suspension, lifting + lowering function, 2nd axle as lifting axle, WABCO SmartBoard, weight detection / axle load display via EBS-Canbus signal for display on display in the driver's cab (truck must be prepared accordingly, no calibrated scale), release valve on the front axle, spring brake on the rear axle, two pairs of pneumatic container locks for roll-off containers, storage box made of galvanized sheet steel approx.: 1,000x300x600mm, storage box for container net approx.: 1,000x300x600mm, side protection device closed, underrun protection fixed, rear apron on the underrun protection, A-sign foldable, ramp compartment including aluminum ramps (2,800 mm, long 470 mm wide, approx. 10,600 kg load capacity/pair), hot-dip galvanized chassis, modular lights, some LED, 2 additional LED reversing lights at the rear of the vehicle. La-Si package: 8 pieces of UVV fall lashing brackets (LC 8,000 daN) mounted to the existing hole pattern in the outer frame (protruding by the material thickness) ? Arrangement: 1 pair in front of the rear carrier / 3 pairs in the flat loading area, 1 pair of foldable lashing eyes (LC 13,500 daN) on the front wall carrier, 3 pairs of foldable lashing eyes (LC 10,000 daN) recessed in the outer frame, 8 interchangeable trough stops for lateral centering of the tipping troughs, 4 front trough stops plugged in with a swinging stop. Duomatic coupling head / 15-pin power supply Draw fork 2,100 mm plus 500 mm lowering device / 40 mm DIN towing eye Truck coupling height: approx. 780-980 mm Container length: 5,500 mm - 7,000 mm i.Li. or 2x 10 cbm ASK troughs or construction machine transport Height: approx. 950 mm with unloaded vehicle (centering edge 970 mm) 27,000 kg GG technically possible multiple available!! Hüffermann Krandienst GmbH: we trade, we rent, we repair. Roll-off trailers, roll-off tippers, garbage collection vehicles, mobile cranes and work platforms... Talk to us! Do you need financing? We would be happy to provide you with a non-binding financing offer. The offer is subject to change, without warranty or guarantee. Subject to prior sale. A deposit of 10% of the purchase price is required for a reservation. No reservation or claim to availability exists until the money has been received. The purchase is only concluded when payment has been received. The vehicle remains the property of Hüffermann Krandienst GmbH until full payment has been made. Payments are only accepted in euros at no additional cost to the seller and only by bank transfer or cash. No checks.

Condition: new, maximum load weight: 8,500 kg, overall weight: 11,990 kg, axle configuration: 2 axles, loading space length: 5,000 mm, loading space width: 2,420 mm, loading space height: 500 mm, Equipment: ABS, * KA-TA-R 11.9 Masterline: * Front wall and floor hot-dip galvanized Fjdpfx Aeq Hg D Hjfmjpp * Wabco ABS * Emergency release device for spring-loaded cylinder * Drum brakes, 2 x 7 to. Gigant axles * Parabolic springs with tandem compensation unit * 300 mm height-adjustable hot-dip galvanized drawbar with 40 mm flanged drawbar eye * Jost mech. support winch at the front * 2 mechanical hot-dip galvanized folding supports at the rear * 15-pin power plug * Multi-chamber tail lights * hot-dip galvanized bolted underride guard * Tool box made of galvanized sheet steel on the right side * Plastic quarter mudguards * Hot-dip galvanized chassis * Steel Pal.- 3 side tipper body * Full-length side walls in white, top with inner tube reinforcement, can be folded down without center stanchions with dropside spring jack * Tailgate can be folded down and swivels via man. Central locking * Hot-dip galvanized bolted rear stanchions * 1 x 5 to. lashing ring in each corner Lashing ring in each corner and 4 x 3 to. lashing rings embedded in the outer frame * 4 mm sheet metal floor made of fine-grained steel * Net hooks * Mounting rail at the rear for the feeder ramps * Steel attachments inserted 500 mm high 3 sides swinging * Reinforced body with load securing certificate to EN 12642 XL * 1 pair of aluminum docking ramps approx. 3,570 x 400 mm (load capacity 8 to. / pair) suitable for rubber-tyred and tracked vehicles * Lockable storage compartment underneath the loading area recessed into the chassis from the rear * Axles, springs, air reservoir and support winch painted black * Tires 285/70 R 19.5 * Side wall paint in 9010 pure white * New vehicle with manufacturer's warranty * Subject to errors and prior sale * Available for immediate delivery from Egestorf on the A7

Condition: used, maximum load weight: 14,000 kg, overall weight: 18,000 kg, axle configuration: 2 axles, first registration: 10/2013, loading space length: 6,800 mm, total width: 2,550 mm, total height: 1,400 mm, Year of construction: 2013, Equipment: ABS, ABS, EBS, automatic slack adjusters, 2x 10 to. axles (BPW), air suspension, drum brake, spring-loaded brake on the rear axle, pneumatically lowerable drawbar, release valve on the front axle, ratchet tensioner, hydraulic side clamp, closed storage box, two reversing lights, net box, spare wheel holder, closed side underride guard, fixed rear underride guard, rear skirt on the underride guard, folding A-plate, container size 2x10 cbm ASK skip. Hüffermann Krandienst GmbH: we trade, we rent, we repair. Roll-off trailers, roll-off tippers, refuse collection vehicles, mobile cranes and working platforms... Talk to us! Fedpsuzdm Ajfx Afmepp Would you like financing? We will be happy to provide you with a non-binding financing offer. The offer is subject to change, without guarantee or warranty. Subject to prior sale. A deposit of 10% of the purchase price is required for a reservation. There is no reservation or entitlement to availability until payment has been received. The purchase is only concluded upon receipt of payment. The vehicle remains the property of Hüffermann Krandienst GmbH until full payment has been received. Payments are only accepted in euros without additional costs for the seller and only by bank transfer or cash payment. No checks.

Condition: new, maximum load weight: 14,680 kg, overall weight: 18,000 kg, axle configuration: 2 axles, Year of construction: 2025, * RA-T 18.0 / 018: * Wabco EBS-E (electronic braking system) * RDÜ tire pressure monitoring * Emergency release device for spring-loaded cylinder * Disc brakes * 2 x 11 t Sauer axles * Air suspension (automatic lowering when the brake is uncoupled) * Tow bar approx. 2,300 mm long with 40mm towing eye and height adjustment via spring & turnbuckle * Plastic toolbox 450 x 470 mm, right side * Side net box 1,000 x 500 x 5000 mm * Closed plastic fenders FA & RA * Closed side underride protection as advertising space * Rear underride guard * Plastic bumper buffer, rear * Hazardous material sign, rear * 15-pin power connector * LED taillights * Track length approx. 6,830 mm * Pneumatic 4-way clamp lock * Mechanically adjustable stops (2 positions) front left and right on the tracks Fedjv Nulzjpfx Afmopp * 265/70 R 19.5 twin tires * 3,220 kg unladen weight * --Permitted total weight of 20,000 kg technically possible-- * Approx. 1,130 mm driving height loaded * Suitable for 5,500 – 7,000 mm container lengths * Hot-dip galvanized chassis * Air tank, axles, slewing ring and tow bar * New vehicle with manufacturer warranty * Errors and prior sale excepted * Immediately available from Egestorf

Condition: new, maximum load weight: 8,850 kg, overall weight: 11,900 kg, axle configuration: 2 axles, loading space length: 5,000 mm, loading space width: 2,420 mm, loading space height: 500 mm, Year of construction: 2024, * KA-TA-R 11.9 "Masterline": * Hot-dip galvanized floor and bulkhead * EBS braking system * Emergency release device for spring-loaded cylinders * Tire pressure monitoring system * Drum brakes * 2 x 5.5 ton BPW axles * Parabolic springs with tandem compensating unit * 300 mm height-adjustable drawbar with 40 mm flange drawbar eye * Jost mechanical landing gear at the front * 2 mechanical landing gears at the rear Hot-dip galvanized folding supports * Plastic toolbox approx. 750 x 350 x 300 mm on the right side * 15-pin power connector * LED lighting Fpjdpfxjl Thyxo Afmsp * Bolted underride protection * Plastic quarter fender * Net hooks on the sides and rear in the central locking bearings, as well as two on the front wall * Steel pallet 3-way tipping body (continuous side walls - without center stanchions - foldable with side wall spring lifter) * Bolted rear stanchions * Combination steel wing doors, rear wall with two asymmetrical wings, divided by 270°, pivoting and locking, not foldable, and with additional pendulum frames for automatic rear wall opening during tipping. Locking via galvanized espagnolette and central locking * Deactivation function for automatic rear wall function when tipping backwards with the wing door open * 1 x 5 ton lashing ring in each corner and on the sides 4 x 3-ton lashing eyes embedded in the outer frame, 4 mm sheet steel floor, rear mounting rail for the landing ramps * Reinforced body with load securing certificate according to EN 12642 XL * 1 pair of aluminum landing ramps approx. 3,310 x 400 mm (load capacity 8 tons per pair) suitable for rubber-tired and tracked vehicles * Rear-lockable storage compartment embedded in the chassis below the loading area * Front wall, tipping platform, rear stanchions, underrun protection, mechanical Hot-dip galvanized drop legs * Side walls and tailgate painted in RAL 9010 pure white * Side walls can be painted in a RAL color for an additional charge * Axles, springs, flanged towing eye, air chamber, and landing gear painted in a black color * New vehicle, not registered, with manufacturer's warranty * Errors and prior sale subject to change * Available for immediate delivery from Egestorf on the A7

Condition: new, maximum load weight: 12,080 kg, overall weight: 14,400 kg, axle configuration: 2 axles, loading space length: 3,900 mm, loading space width: 1,920 mm, loading space height: 415 mm, Year of construction: 2022, Equipment: ABS, * ETM-TA 14.4: * Wabco ABS braking system * Emergency release device for spring-loaded cylinders * Drum brakes, 2 x 7 tonnes. Gigant axles * Parabolic springs with tandem compensation unit * Height-adjustable drawbar (+/- 150 mm) with 40 mm screw drawbar eye * Jost support winch at the front, side impact protection * Foldable A-plate at the rear * 15-pin power plug, multi-chamber tail lights * Fixed steel front and side walls Fjdpfx Afol Th Eyomjpp * Plug-in steel rear wall * Floor made of 50 mm softwood * 1 sliding plate support 750 x 1,000 mm in the front area including 2 trough stops at the front that can be plugged into 2 positions * 4 reversible trough stops that can be plugged into 2 positions for laterally centering the troughs * 1 x (13.5 ton) UVV lashing ring on each side for hanging tensioning elements * 2 ratchet tensioners (spindle adjustment) with compensation chain and quick shortener (tension force 6,300 kg) * Rear cross member for attaching aluminum ramps including 2 additional rear fall supports * Loading edge unloaded approx. 710 mm * Chassis, bulkhead, side walls, fender, drawbar, rear fall supports hot-dip galvanized * the axles, springs, support winch, air tank painted in a black tone * Tires: 285/70R19.5, wheelbase: 1,140 mm * Loading edge unloaded: approx. 710 mm, sold without container * Color hot-dip galvanized * Vehicle has a daily registration in 06/2024, due to missing tire pressure monitoring system and has not been loaded/used * New vehicle with manufacturer warranty * Errors and prior sale subject to reservation * available immediately from Egestorf on the A7

Condition: new, maximum load weight: 8,870 kg, overall weight: 11,900 kg, axle configuration: 2 axles, loading space length: 6,270 mm, loading space width: 2,470 mm, loading space height: 400 mm, Year of construction: 2025, * ETÜ-TA-R 11.9: * Loading area 6.27 m * Suitable for container transport * RDÜ tire pressure monitoring * EBS braking system * Emergency release device for spring-loaded cylinders * Drum brakes, 2 x 5.5 tonnes. BPW axles * Parabolic springs with compensating unit * Drawbar height adjustable by 300 mm * Jost landing gear at the front Fpodorvvfwepfx Afmop * External hot-dip galvanized folding supports at the rear * Plastic quarter fenders * LED lighting * Hot-dip galvanized chassis, drawbar, bulkhead, rear wall, rear stanchions, and loading ramps * 50 mm softwood floor * Device for retrofitting container locks in front of the bulkhead * Bolted smooth sheet metal bulkhead * Foldable trapezoidal steel side walls with side wall spring lifter * Steel rear wall can be inserted between the ramp brackets when not in use, inside the bulkhead * Bolted rear stanchions * Perforated outer frame, angled at approximately 45 degrees with a 2-ton lashing capacity every 480 mm * Installation of 3-ton Drop lashing rings available every 600 mm * 1 x 6.3 ton lashing ring in each of the front and rear corners * Various holes in the front and end beams for 1.2 ton lashing options * One-piece mechanical loading ramps with spring mechanism for one-person operation, approx. 2,750 x 600 mm (can be collapsed to within 20 mm) * Rear approach slope approx. 860 mm * Wheelbase: 990 mm * Tires: 235/75R17.5 * Side walls painted in RAL 9010 pure white * Side walls painted in a RAL color available for an additional charge * Plastic toolbox * Subject to errors and prior sale * Available for immediate delivery from Egestorf

Condition: new, maximum load weight: 16,000 kg, overall weight: 21,000 kg, axle configuration: 2 axles, loading space length: 5,500 mm, loading space width: 2,420 mm, loading space height: 700 mm, Year of construction: 2024, * KA-TA-RT 21.0 ML: Fpodpfx Aor Dpzusfmop * Without ABS / EBS with 40 km/h approval * Spring-loaded parking brake, drum brakes * Gigant axles * Tandem balancing unit with 100 mm wide parabolic springs * Support winch at the front * mech. Fall supports at the rear * firmly welded drawbar with low-maintenance cap for K80 ball head coupling (can be adjusted by + 77 mm / 33 mm via head plate) with raised boom for the connecting cables * 12 V 7 + 4-pin power cable * LED lighting system 12 / 24 V with protective grille * 2 LED work lights at the rear, switchable from the towing vehicle without installation on the towing vehicle side * Side marker lights with indicator control * Plastic quarter fender * Plastic tool box approx. 750 x 350 x 300 mm on the right side * Chassis made of fine-grain steel * Steel pallet 3-way tipping structure with M-Strong side walls (front wall fixed, continuous side walls - without center stanchions - swinging via manual central locking and mechanically foldable with side wall spring lifter * hydraulic rear wall 500 mm high as hydr. chute and a 115° opening angle * 4 mm Hardox 450 steel floor * 1 x 7 tonne lashing eyes in each corner and 4 x 3 tonne lashing eyes on each side - recessed and foldable * Hot-dip galvanised two-step ladder in front of the front wall in FR left) * 1 pair of aluminium landing ramps (10 tonne / pair with axle distance over 2,500 mm) 3,570 x 410 x 120 mm suitable for rubber-tired and tracked vehicles * 2 mounting slots for aluminum docking ramps embedded in the chassis from the rear Load securing in accordance with EN 12642 XL * --Coupling height loaded approx. 530 mm * unloaded approx. 590 mm-- * Body paint in RAL 9010 pure white * Chassis, drawbar, rear drop supports, underrun protection hot-dip galvanized * Axles, air tank, support winch at the front * K80 coupling painted in a black tone * New vehicle with manufacturer's warranty * Errors and prior sale subject to reservation * Available for immediate delivery from Egestorf

Condition: new, maximum load weight: 18,900 kg, overall weight: 24,000 kg, axle configuration: 3 axles, loading space length: 7,000 mm, loading space width: 2,480 mm, Year of construction: 2025, * TRA-Kombi 24.0: * Wabco EBS-E (electronic braking system) * Emergency release device for spring-loaded cylinders * Drum brakes * TPMS (Tire Pressure Monitoring System) * 3 x 11 t Gigant axles * Air suspension with manual lowering at the rear * Center axle liftable * Pneumatically lowerable drawbar, 2,100 mm long, with 50 mm towing eye and height adjustment device * Tool box made of powder-coated steel sheet and spare wheel holder in basket design on the right side * Contour marking tape on sides and rear, reflective * Side underride protection * Plastic quarter mudguards with splash protection * Plastic rear impact protection buffers * LED tail lights * 15-pin power connector * Hot-dip galvanized main frame with raised outer frame (approx. 25 mm higher) for guiding roll containers * Steel floor with wheel recesses in the bogie area * For roll-off container transport, container lengths from 5,500 - 7,000 mm possible * Pneumatic 4-point clamp locking system and mechanically pluggable front stop angles in the track * Load certificate according to DIN 30722-1 * Transport of up to 2 skip containers with max. 10 m³ capacity possible * Includes 8 repositionable skip stops for lateral centering of containers, the front 4 skip stops are pluggable with swiveling stops * 3 pairs of 10 t UVV lashing rings on the sides for attaching tensioning elements for positive and frictional securing of the skips * 4 cloverleaf lashing rails on each side and 1 pair of 13.4 t UVV lashing rings to the front * Load securing certificate according to DIN EN 12195-1, DIN EN 12640, DIN EN 12642, and VDI 2700 * Weld seam anti-slip coating in the running area of the drive-on slope * Mechanical drop-down support legs at the rear Fjdpfx Aotplv Tofmepp * 1 pair of aluminum drive-on ramps (16 t/pair), 2,800 x 400 mm, suitable for rubber-tired and tracked vehicles (lockable storage compartment accessible from the rear) * Tires: 235/75 R17.5 * Loaded ride height approx. 1003 mm * Payload: 18,900 kg * Technically permissible gross weight: 27,000 kg * Axles, slewing ring, drawbar, and air tanks painted in black * New vehicle without first registration, comes with manufacturer’s warranty * Errors and prior sale excepted * Available from week 50/2025

Condition: new, maximum load weight: 10,500 kg, overall weight: 14,400 kg, axle configuration: 2 axles, loading space length: 7,000 mm, loading space width: 2,470 mm, loading space height: 400 mm, Year of construction: 2025, * EBS (electronic braking system) * Emergency release device for spring brake cylinders * Drum brakes * 2 x 7 t Gigant axles * Air suspension with lift and lowering system * Drawbar height adjustable by approx. 300 mm * Drawbar extension by 250 mm to 2,250 mm * Tire pressure monitoring with display capability in the truck via EBS signal – no truck-side installation required * 15-pin power connector * LED lighting * Front landing gear * Rear folding support legs, externally mounted * Plastic toolbox approx. 858 x 500 x 500 mm, front right outside on the bulkhead * Side underrun protection * Plastic quarter mudguards * 50 mm softwood floor * Provisions in front of the bulkhead and at the rear for retrofitting 20" container locks * Bolted bulkhead made of smooth sheet metal * Side walls made of trapezoid-profiled steel sheet, foldable, center-divided (1x) * Rear wall made of steel, insertable between the ramps, storage bracket for non-use inside in front of the bulkhead * Rear stanchions bolted * Perforated outer frame, approx. 45° bent, with 2 t lashing capacity every 480 mm * Installation of 3 t folding lashing shackles possible every 600 mm – 4 lashing rings installed per side * One 6.3 t lashing ring in each front and rear corner * Various holes for 1.2 t lashing options in the bulkhead and end crossmember * One-piece mechanical grating ramps with spring mechanism for one-man operation, approx. 2,750 x 600 mm (can be collapsed to 20 mm) * Rear approach slope approx. 860 mm * Chassis, drawbar, bulkhead, tailgate, folding support legs, and ramps hot-dip galvanized * Axles, springs, air tanks, flange eye, and landing gear painted black * Side wall color freely selectable up to approx. 2 weeks before production date; no metallic or special colors allowed * --reinforced and certified body according to EN 12642 XL including load securing certificate-- * New vehicle with manufacturer's warranty * Subject to errors and prior sale Fjdpfx Afel Th Dfemepp * Immediately available in Egestorf

Condition: new, maximum load weight: 14,660 kg, overall weight: 19,000 kg, axle configuration: 2 axles, loading space length: 6,270 mm, loading space width: 2,470 mm, loading space height: 400 mm, Year of construction: 2025, * ETÜ-TA-R 19.0: * Wabco EBS brake system * RDÜ tire pressure monitoring system * Emergency release device for spring brake cylinders * Drum brakes * 2 x 10 t BPW Eco axles * Parabolic springs - 110 mm wide - with tandem compensation unit * Drawbar with 50 mm flange eye and height-adjustable drawbar * Jost landing gear at the front * Fold-out support legs at the rear Fedpfxjl Th Hlj Afmspp * Side underrun protection * Plastic quarter mudguards * 15-pin electrical plug * LED tail lights * 50 mm softwood flooring * Preparation in front of the front wall for subsequent installation of container locks * Bolted front wall made of smooth sheet metal * Side walls made of trapezoidal-profile steel sheet, foldable, with drop-side spring-assisted lifter * Steel rear wall, retractable between the ramps - holder for unused wall inside at the front wall * Bolted rear side stanchions * Perforated outer frame, approx. 45 degrees angled, with 2 t lashing capacity every 480 mm * Installation of 3 t flush lashing rings possible every 600 mm * In each corner at the front and rear, 1 x 10 t lashing ring; various holes for 1.2 t lashing options in the front and rear bulkheads * One-piece mechanical grating access ramps with spring mechanism for single-person operation, approx. 2,750 x 620 mm (can be retracted to 20 mm) * Rear approach ramp approx. 860 mm * Chassis, drawbar, front wall, rear wall, access ramps, and folding supports hot-dip galvanized * Paint finish of the drop sides in RAL 9010 pure white * Paint finish of the side walls in any RAL color available at extra cost * Axles, springs, air tanks, drawbar eye, and landing gear painted in black shade * New vehicle with full manufacturer's warranty * Errors and prior sale excepted * Immediately available ex Egestorf

Condition: new, maximum load weight: 8,800 kg, overall weight: 11,900 kg, axle configuration: 2 axles, loading space length: 5,370 mm, loading space width: 2,470 mm, loading space height: 400 mm, Year of construction: 2025, * ETÜ-TA-R 11.9: * Loading platform 5.37 m * RDÜ (Tire Pressure Monitoring System - TPMS) * EBS braking system * Emergency release device for spring brake cylinders * Drum brakes, 2 x 5.5 t Gigant axles * Parabolic springs with equalizer assembly * Height-adjustable drawbar, adjustable by 300 mm * Jost landing gear at the front * External folding support legs at the rear * Plastic toolbox mounted front right on the bulkhead * Side underrun protection * LED lighting * Plastic quarter mudguards * 50 mm softwood floor * Bolt-on bulkhead made of smooth sheet metal * Side walls made of trapezoidal-profiled steel, foldable with drop-side spring assist * Rear wall made of steel, can be stored between ramp holders at the front of the bulkhead when not in use * Bolted rear stanchions * Perforated outer frame, bent approx. 45 degrees, with 2 t lashing capacity every 480 mm * Installation of 3 t drop lashing rings possible every 600 mm * One 6.3 t lashing ring in each of the front and rear corners * Various 1.2 t lashing points in the front and rear cross members * One-piece mechanical grating ramps with spring mechanism for single-person operation, approx. 2,750 x 600 mm (can be pushed together to 20 mm) Fpodol Th Ncjpfx Afmep * Approach angle at rear approx. 860 mm chassis * Drawbar, bulkhead, tailgate, folding supports, and ramps hot-dip galvanized * Axles, springs, air tanks, and 40 mm flange towing eye painted black * Wheelbase: 990 mm * Tires 235/75R17.5 * Drop sides painted in RAL2011 deep orange * Side wall painting in any RAL color available at extra cost * New vehicle with manufacturer's warranty * Subject to errors and prior sale * Immediately available from Egestorf

Condition: new, maximum load weight: 37,500 kg, overall weight: 48,000 kg, axle configuration: 3 axles, Year of construction: 2024, * TS 3 RM 30.0: * Wabco EBS-E (electronic braking system) * RDÜ tire pressure monitoring system * Emergency release device for spring-loaded cylinders * Drum brakes * 3 x 11-ton BPW axles * Air suspension with lifting and lowering system and RtR valve * Last axle as self-steering axle with electro-pneumatic steering lock * Side impact protection * Landing gear at the front and swivel supports at the rear of the chassis * 15-pin power connector * LED taillights * Mechanical Adjustable warning sign packages at the front and rear Fpjdpfjl Tiiyox Afmsp * Rotating beacon (removable) at the rear left * Straight sheet steel fenders * Spare wheel holder in front of the bulkhead cross member (without spare wheel) * Trailer platform with 45° beveled front corners and a toolbox at the front made of galvanized, powder-coated sheet steel (W = 2,480 x H = 500 x L = 665 mm) with a hinged lid * 400 mm aluminum side walls (RAL 9010) on the sides of the trailer platform, foldable and removable * Rear wall -150 mm- high * Rear slope on the trailer platform to the low bed, approx. 700 mm long, each with one recessed lashing ring * Trailer platform with 50 mm clamped wooden planks and low-loading platform with 60 mm clamped wooden planks * Teardrop plate above the axles * 9 mechanical folding extensions to 3 m Total width, but not including the rear slope (extension planks present with closed storage compartment perpendicular to the direction of travel under the loading area) * 2 lashing bars embedded in the outer frame of the semi-trailer platform on each side, 3 lashing rings on each side in the low-loader platform, and an additional 1 lashing ring in the center of the rear end beam, 2 x 5 ton lashing rings screwed to the bottom of the outer frame of the wheel wells on each side, * 2 x 6.4 ton lashing rings on each side. UVV lashing rings in the excavator boom rest * Excavator boom rest from the end of the last rigid axle over the steering axle to the end support, continuous with internal reinforcement profile approx. L = 2,450 x W = 770 mm x D = 270 mm * Two wheel recesses on each side, 390 mm deep and 640 mm wide, with retractable covers for transporting wheel loaders with a wheelbase of 3,120 - 3,620 mm, front recess at the bottom, slanted upwards by 1,100 mm to a length of 2,050 mm, rear recess at the bottom, slanted upwards by 580 mm to a length of 1,550 mm * Hydraulic. Folding ramp with extendable tip, approx. 4,650 x 720 mm, including load-holding valves and hydraulic lateral ramp adjustment. * The outer board on the ramp is made of 50 mm hardwood. * Loading area above the turntable: approx. 3,950 x 2,480 mm. * Loading height (unloaded): approx. 1,470 mm. * Lower loading area: approx. 8,500 x 2,520 mm. * Loading height (unloaded): approx. 910 mm (including 860 mm approach slope). * Chassis, folding supports at the rear, loading ramps, mechanical. Hot-dip galvanized folding extensions * -- Axles, springs, and air chambers painted in a single black tone -- * Suitable for 2- and 3-axle tractors * Fifth wheel height: approx. 1,220 mm * Tires 235/75R17.5 * Gross vehicle weight of 48,000 kg technically possible * Vehicle is hot-dip galvanized * Side walls painted in RAL 9010 pure white * Side walls painted in a RAL color available for an additional charge * New vehicle with manufacturer's warranty * Errors and prior sale subject to change * Available for immediate delivery from Egestorf

Condition: new, maximum load weight: 14,550 kg, overall weight: 18,000 kg, axle configuration: 2 axles, Year of construction: 2025, * Wabco EBS-E (electronic braking system) * Emergency release device for spring-loaded cylinders * 19.5" disc brakes * Automatic braking when the transverse clamping units are opened * 2 x 10-ton BPW wide-track axles * Air suspension (automatic lowering when the brake is uncoupled) * Tire pressure monitoring with display option in the truck via EBS signal - no truck-side installation required - * Pneumatically lowering towing bar, 1,800 mm long, with 40 mm towing eye and height adjustment via tension spring and turnbuckle Fpedpel Tn U Refx Afmep * Plastic toolbox, 858 x 500 x 500 mm, on the right side * Storage box for cargo net made of galvanized perforated sheet metal, 1,000 x 500 x 500 mm, on the side * Closed plastic fenders, front and rear * Closed side impact protection (RAL 9010 pure white) as Advertising space * Rear underrun protection * Plastic bumper buffers at the rear * Foldable A-sign * Hazardous goods sign with accompanying document pocket and reflective parking warning sign at the rear * 15-pin power connector * LED lighting system with protective roof * 2 LED reversing lights (switched via reverse gear) * Additional front loading with rear track lowering and plug-in stop * Roller recesses in the area of the turntable with mechanical locking. Adjustable stop angles (2 positions) on the front left and right of the tracks * Track length approx. 6,830 mm * Pneumatic 4-point clamp locking system * For the transport of external roller containers according to DIN 30722 Part 1 - DEKRA load securing certificate available * Loaded loading height approx. 1,130 mm * Chassis and locking components hot-dip galvanized * Air tank, axles, turntable, and tension scissors painted in a black tone * --GVW of 20,000 kg technically possible-- * New vehicle without first registration and with manufacturer's warranty * Errors and prior sale subject to change * Available for immediate delivery from Egestorf

Condition: new, maximum load weight: 10,500 kg, overall weight: 14,400 kg, axle configuration: 2 axles, loading space length: 7,000 mm, loading space width: 2,470 mm, loading space height: 400 mm, Year of construction: 2025, * EBS (electronic braking system) * Emergency release device for spring-loaded cylinders * Drum brakes * 2 x 7 t Gigant axles * Air suspension with lifting and lowering system * Drawbar height adjustable by approx. 300 mm * Drawbar extension by 250 mm to 2,250 mm * Tire pressure monitoring with display option in the truck via EBS signal – no truck-side installation required * 15-pin power connector * LED lighting * Landing gear at the front * Rear fold-out supports, externally mounted * Plastic toolbox approx. 858 x 500 x 500 mm, located front right on the outside of the front wall * Side underrun protection * Plastic quarter mudguards * 50 mm softwood floor * Provision for retrofitting 20'' container locks in front of the front wall and at the rear * Bolted smooth sheet metal front wall * Side walls made of trapezoidal-profiled steel sheet, folding, split in the middle * Steel rear wall, sliding, can be stored in front of the front wall when not in use * Bolted rear stanchions * Perforated outer frame, approx. 45 degrees angled, with 2 t lashing capacity every 480 mm * Installation of 3 t retractable lashing brackets possible every 600 mm – four lashing rings installed per side Fpsdpfxjl Thvxj Afmsp * One 6.3 t lashing ring in each front and rear corner * Various holes in the front crossmember and rear end member for 1.2 t lashing options * One-piece mechanical grid ramps with spring system for single-operator use, approx. 2,750 x 600 mm (can be pushed together to 20 mm) * Rear approach slope approx. 860 mm * Chassis, drawbar, front wall, tailgate, folding supports, and loading ramps hot-dip galvanized * Axles, springs, air tanks, flange towing eye, and landing gear painted in black * Color of side walls freely selectable up to approx. 2 weeks before production date (excluding metallic and special colors) * --reinforced and certified body according to EN 12642 XL, including load securing certificate-- * New vehicle with manufacturer warranty * Subject to errors and prior sale * Immediately available in Egestorf

Condition: new, maximum load weight: 8,450 kg, overall weight: 11,900 kg, axle configuration: 2 axles, loading space length: 5,000 mm, loading space width: 22,420 mm, loading space height: 1,500 mm, Year of construction: 2024, * KA-TA-R 11.9 Masterline: * incl. 1 mtr grid attachments * EBS brake system * Emergency release device for spring brake cylinders * RDÜ tire pressure monitoring * Drum brakes * 2 x 5.5 to. BPW axles * Parabolic springs with tandem compensation unit * 300 mm height-adjustable hot-dip galvanized drawbar with 40 mm flanged drawbar eye * Jost mech. support winch at the front * 2 mechanical hot-dip galvanized folding supports at the rear * Tool box made of galvanized sheet steel on the right side * 15-pin power plug * Bolted underride guard with LED tail lights * Plastic quarter mudguards * Mesh hooks at the side and rear in the bearings of the central locking system and 3 pieces on the outside of the bulkhead Fedpfxop Ncl Se Afmopp * Hot-dip galvanized chassis * Fully galvanized steel Pal. 3 side tipper body * Full-length side walls without central stanchion can be folded down with dropside spring lifter * Tailgate can be folded down and swung open via man. Central locking * hot-dip galvanized bolted rear stanchion * 1 x 5 to. lashing ring in each corner Lashing ring recessed and foldable in each corner and 4 x 3 tons at each side. * Lashing rings recessed in the outer frame and hinged * 4 mm sheet steel floor * Rear mounting rail for feeder ramps * Reinforced body with load securing certificate to EN 12642 XL * 1 pair of aluminum docking ramps approx. 3,570 x 400 mm (load capacity 8 to. / pair) suitable for rubber-tyred and tracked vehicles * Storage compartment lockable from the rear under the loading area recessed in the chassis * 235/75 R 17.5 tires * Axles, springs, air reservoir, drawbar and support winch painted black * Hot-dip galvanized side wall paint * 1 metre galvanized grid attachments * Sample pictures * New vehicle with manufacturer's warranty * Subject to errors and prior sale * Immediately available from Egestorf on the A7

Condition: new, maximum load weight: 10,700 kg, overall weight: 14,400 kg, axle configuration: 2 axles, loading space length: 5,000 mm, loading space width: 2,420 mm, loading space height: 1,500 mm, Equipment: ABS, * KA-TA-R 14.4: * Front wall and floor hot-dip galvanized * Wabco ABS * Emergency release device for spring-loaded cylinder * Drum brakes * 2 x 7 to. Gigant axles * Parabolic springs with tandem compensation unit * 300 mm height-adjustable hot-dip galvanized drawbar with 40 mm flanged drawbar eye * Jost mech. support winch at the front * 2 mechanical hot-dip galvanized folding supports at the rear * 15-pin power plug * Multi-chamber tail lights * hot-dip galvanized bolted underride guard * Tool box made of galvanized sheet steel on the right side * Plastic quarter mudguards * Hot-dip galvanized chassis * Steel Pal.- 3 side tipper body * continuous side walls in white on top with inner tube reinforcement without center stanchions - can be folded down with dropside spring lifter * Tailgate can be folded down and swivels via man. Central locking * Hot-dip galvanized bolted rear stanchions * 1 x 5 to. lashing ring in each corner Lashing ring in each corner and 4 x 3 to. lashing rings embedded in the outer frame * 4 mm sheet metal floor made of fine-grained steel * Net hooks, mounting rail at the rear for the feeder ramps Fedpfxsp Ncmae Afmjpp * Preparation for later retrofitting of side wall attachments * Reinforced body with load securing certificate in accordance with EN 12642 XL * 1 pair of aluminum docking ramps approx. 3,570 x 400 mm (load capacity 8 to. / pair) suitable for rubber-tyred and tracked vehicles * Lockable storage compartment below the loading area recessed into the chassis from the rear * Axles, springs, air reservoir and support winch painted black * Side wall body color in 9010 pure white * 1 metre galvanized lattice extensions * Tires 285/70 R 19.5 * Sample pictures * New vehicle with manufacturer's warranty * Subject to errors and prior sale * Immediately available from Egestorf on the A7

Condition: new, maximum load weight: 31,000 kg, overall weight: 40,000 kg, axle configuration: > 3 axles, loading space length: 9,290 mm, loading space width: 2,520 mm, loading space height: 950 mm, * PT 40.0 profile: * Wabco EBS-E (electronic braking system) * Emergency release device for spring-loaded cylinders * Drum brakes * 4 x 11 tonne Gigant axles * Air suspension with lifting and lowering system and RtR valve * Manometer pressure indicator for determining load weight (axles separated into 2 air suspension circuits) * Side impact protection * Swivel supports at the rear of the chassis frame * Mechanically adjustable warning sign packages at the front and rear * Front plastic quarter fender with splash guard * Rear straight galvanized. Sheet steel aprons with splash guard * Reflective contour tape on the side and rear * EBS multi-voltage system with 12 & 24 V electrics * 15-pin power plug * LED lighting system 12 / 24 V * LED rotating beacon (removable) at the rear * 2 LED reversing lights (switched via reverse gear) * Pull scissors with 50 mm pull eye and height adjustment * Tool box made of galvanized sheet steel, black powder-coated, approx. 1,000 mm wide, 600 mm deep, 300 mm high * Front section in front of the bogie platform approx. 490 mm long with 45° corners * ROBOT welded ANTI-SLIP coating for the steel plate of the bogie platform * La-Si package consisting of: in front of the front wall support on the left & right 1 x 13.4 ton each. UVV lashing eye, 4 holes on each side in the bogie platform with a lashing force of 2 tons each, 1 pair of lashing eyes (13.4 tons) hanging at the rear left and right in front of the rear carrier, 4 pairs of UVV lashing rings (10 tons) on each side, can be swiveled and lowered, can be loaded in all directions and embedded in the outer frame, 3 stake pockets on each side with a simultaneous 2 ton lashing option * Hot-dip galvanized mechanical folding boom for a total width of 3 meters (but not in the rear slope) Fpedsl Tnu Ajpfx Afmep * Plank holder for widening under the chassis on the left in the longitudinal direction * Excavator boom storage above the rear axle to the end carrier approx. 2,100 mm long and approx. 190 mm deep, 2 pairs of 6.4 tons on each side. Lashing rings in the excavator boom storage * Hardwood floor on the running surfaces of the low-loading platform * Hydraulic one-piece ramps (approx. 3,000 x 720 mm) mechanically laterally adjustable * Outer planks of the ramps made of hardwood * Steel construction in preparation for 6-way control slide * Loading edge unloaded approx. 950 mm +/+ 20 mm chassis * Bogie, folding boom, mechanical drop supports, ramps hot-dip galvanized * --Axles, air tank, pull scissors painted in a black tone-- * Tires 235/75 R 17.5 * Vehicle has a daily registration in 07/2024, due to missing tire pressure monitoring system and has not been loaded/used * New vehicle with manufacturer's warranty * Errors and prior sale subject to reservation * Available for immediate delivery from Egestorf

Condition: new, maximum load weight: 23,700 kg, overall weight: 30,000 kg, axle configuration: 3 axles, Year of construction: 2024, * T3 Profi 30.0: * Wabco EBS-E (electronic braking system) * RDÜ tire pressure monitoring * Emergency release device for spring-loaded cylinders * Drum brakes * 3 x 11 ton BPW Eco axles Fpjdpfjl Tq Eusx Afmep * Air suspension with manual lowering at the rear * Pressure gauge pressure display for determining the load weight (axles separated into 2 air suspension circuits), * Side impact protection * Swivel supports at the rear of the chassis frame * Mechanically adjustable warning sign packages at the front and rear * Front axle closed. Plastic fenders and rear straight galvanized sheet steel aprons, each with splash guard * Reflective contour tape on the side and rear * Hinged lid (hot-dip galvanized) for the toolbox in the bogie platform * LED tail lights * Rotating beacon (removable) at the rear * Pull scissors with 40 mm pull eye and height adjustment via tension spring & turnbuckle * 2 x 7-pin power plugs * 4 stake pockets on each side with simultaneous 2 ton lashing option * La-Si package consisting of: 2 lashing eyes (6.4 ton) at the front left & right on the main frame of the bogie platform, 5 pairs of UVV lashing rings that can be swiveled and lowered, can be loaded in all directions and are embedded in the outer frame - 13.4 ton in the corners, otherwise 10 ton * 6 pairs of mechanical folding booms for 3 mtr. Total width (but not in the rear slope) * Widening planks placed in the middle of the loading area * hydr. one-piece loading ramps (approx. 3,000 x 720 mm) laterally adjustable * Loading area above the turntable: approx. 1,960 x 2,520 mm * Loading height unloaded approx. 1,070 mm * Rear loading area: approx. 6,500 x 2,520 mm * Loading height unloaded approx. 910 mm (incl. 860 mm approach slope) * Chassis, bogie, drawbar, folding extensions & loading ramps hot-dip galvanized * Axles, turntable, air tank etc. painted in a black tone * Tires 235/75 R 17.5 * Payload approx. 24,000 kg with 30,000 kg total weight * New vehicle with manufacturer's warranty * Errors and prior sale subject to change * Available for immediate delivery from Egestorf

Condition: new, maximum load weight: 8,620 kg, overall weight: 11,900 kg, axle configuration: 2 axles, loading space length: 5,500 mm, loading space width: 2,420 mm, loading space height: 500 mm, Year of construction: 2024, * KA-TA-R 11.9: * 5.5-meter-long bridge completely finished in RAL 9010 white * Tire pressure monitoring (RDÜ) * Electronic braking system (EBS) * Emergency release device for spring-loaded cylinders * Drum brakes * 2 x 5.5-ton Gigant axles * Parabolic springs with tandem compensating unit * 300 mm height-adjustable, hot-dip galvanized drawbar with 40 mm flange drawbar eye * Jost mechanical landing gear at the front * 2 mechanical landing gears at the rear Hot-dip galvanized folding supports * Toolbox made of galvanized sheet steel on the right side * 15-pin power connector Fpsdpfxjm Angvj Afmsp * LED taillights * Hot-dip galvanized bolted underride protection * Toolbox made of galvanized sheet steel on the right side * Plastic quarter fenders * Net hooks on the sides and rear in the central locking bearings, as well as 3 on the front wall * Hot-dip galvanized chassis * Steel pallet, 3-way tipping body * Continuous side walls without center stanchions, foldable with side wall spring lift * Tailgate foldable and swinging via manual central locking * Hot-dip galvanized bolted rear stanchions * 1 x 5 ton lashing ring in each corner and 4 x 3 ton lashing rings on each side Lashing eyes embedded in the outer frame * 4 mm sheet steel floor * Rear mounting rail for the docking ramps * Preparation for later retrofitting of side wall extensions * Reinforced body with load securing certificate according to EN 12642 XL * 1 pair of aluminum docking ramps approx. 3,310 x 400 mm (load capacity 8 tons per pair) suitable for rubber-tired and tracked vehicles * Rear-locking storage compartment embedded in the chassis below the loading area * Axles, springs, air tank, drawbar, and landing gear painted in a black tone * Body color: RAL 9010 pure white * Side walls and tipping body painted in a RAL color available for an additional charge * Tires: 235/75R17.5 * Wheelbase: 990 mm * New vehicle, not registered, with manufacturer's warranty * Errors and prior sale subject to change * Available immediately Egestorf on the A7