Trailer with working platform

MÜLLER-MITTELTAL T4 40,0 , Agrar, hydr. Rampen,3 m. Paket

Condition: new, maximum load weight: 31,630 kg, overall weight: 40,000 kg, axle configuration: > 3 axles, loading space length: 9,250 mm, loading space width: 2,520 mm, Year of construction: 2026, * T 4: * EBS * Emergency release system for spring accumulators * Drum brakes * 4 x 11 to. Gigant axles * Parabolic springs * Mechanical axle compensation at the front and rear Nedpfxsl Th Evj Ak Delc * Tire pressure monitoring system with display option in the truck via EBS signal - without installation on the truck side * Warning sign packages at the front and rear * Reflective contour strip on the sides and at the rear * EBS multi-voltage system for 12 & 24 V electrical systems * LED rotating beacon (removable) at the rear * 24 V - 15-pin, as well as an additional 12 V - 7+4 pin - power cable * Extended connecting cables for agricultural and forestry tractors * LED lighting * Straight drawbar with 40 mm drawbar eye and stepless height adjustment * Toolbox made of powder-coated sheet steel and spare wheel holder in the body structure on the right side * Closed plastic fender at the front * Straight steel mudguards at the rear, each with splash protection (spray mist suppression) * Side impact protection * Extended offset overhang extended by 500 mm to the front * Turntable platform extended by 520 mm with 45° corners and 3 recessed storage compartments including covers and lockable * Chassis made of high-strength fine-grained steel * Floor above the turntable platform made of 50 mm and in the low-loader platform made of 60 mm hardwood * Outer planks of the loading ramps made of 50 mm bamboo wood * 4 lashing pockets on each side (but no lashing bars included) with simultaneous 2 to lashing capability * Lasi package consisting of: 2 lashing eyes, 6.4 to, at the front left and right on the main frame of the turntable platform, 1 pair of 13.4 to lashing rings on the outer frame on each side at the front and rear, as well as 4 pairs of 10 to lashing rings on each side, pivotable and lowerable, loadable in all directions and recessed in the outer frame, 2 pairs of lashing rings, 6.4 to, on each side in the excavator arm rest, 8 pairs of galvanized folding outriggers for a total width of 3 m (but not in the rear slope) * Extension planks stored in a compartment on the left side * Excavator arm rest above the rear axle to the end of the loading ramp, approximately 2,300 x 740 x 190 mm * Mechanical support legs at the rear * Hydraulic, hot-dip galvanized loading ramps, approx. 3,000 x 720 mm * Hydraulic side ramp adjustment on sliding tube from the ramp shaft * Loading area above the turntable: approx. 2,990 x 2,520 mm, * Rear loading area: approx. 6,280 x 2,520 mm * Loading height when loaded approx. 860 mm (including 860 mm loading ramp) * Chassis, turntable, loading ramps, mechanical folding supports at the rear, hot-dip galvanized * Axles, springs, air tanks and turntable painted in a black tone * New vehicle with manufacturer's warranty * Errors and prior sale are subject to change * Available immediately from Egestorf

Condition: new, functionality: fully functional, empty load weight: 7,500 kg, maximum load weight: 36,500 kg, overall weight: 44,000 kg, axle configuration: > 3 axles, loading space length: 9,190 mm, loading space width: 2,540 mm, loading space height: 900 mm, suspension: steel-air, tire size: 235×75 R17,5, wheelbase: 1,310 mm, Year of construction: 2024, Equipment: ABS, center pivot plate, CETRATEK 4-Axle Low Loader TL89.4 (EU-COC) Short Description Robust low loader for heavy machinery transport. Frame made of high-strength ST-52/S355, optionally fine-grain steel S700. Ramps with 20 t load capacity each, mechanically or hydraulically foldable without loss of capacity. Optionally available as a low-bed trailer; loading height in wheel recess area can be reduced from approx. 900 mm to approx. 500 mm. Dimensions / Configuration Total length: 11,914 mm, total height: 3,775 mm (over ramps) Nsdpfx Aju Rbzvjk Dslc Platform: gooseneck 2,440 mm + loading area 6,750 mm Width: 2,540 mm (+ 250 mm manual extension on each side) Coupling → 1st axle: 2,767 mm; → 2nd/3rd axle: 6,136 mm Axle spacings: front 1,310 mm, rear 1,360 mm Platform height: 900 mm (low-bed approx. 500 mm), track width 1,850 mm Rear ramps: 3,000 × 750 mm, laterally adjustable, 20 t per ramp Drawbar height: 400–900 mm; turntable Ø 110 (CYR) Floor: steel + 45 mm hornbeam hardwood, protective lacquer coating Weights / Capacity a) GVW 44,000 kg → payload approx. 36,500 kg* b) On-road 24,000 kg → payload approx. 16,500 kg * Version a) subject to special approval according to §70 StVZO; certification/DEKRA inspection at extra cost. Towing eye Ø 50 mm (optional Ø 40 mm), unladen weight approx. 7,500 kg Rear supports: manual (hydraulic optional) Steel Structure / Chassis Welding qualification TS EN ISO 9606-1, processes TS EN ISO 4063, shielding gases TS EN ISO 14175 4 × 11 t axles (TRAX), tires 235/75 R17.5 (16 units, PETLAS or equivalent; Continental/Michelin on request at extra cost), rims 6.75×17.5, air suspension, max. 100 km/h permitted Brakes / Electrics WABCO EBS 4S/2M, brake pads 330×200, air tanks 2×80 L + 1×60 L Brake cylinders: 4× Type 24 + 4× Type 24/30, levers 165 mm Voltage 24 V (24 V converter required for 12 V towing vehicle) Side reflectors: 4× LED per side + 2× white front reflectors, taillights 2× LED, 2× triangular reflectors Connections: 7-pin EBS ISO 7638, 7-pin ISO 1185/3731, 15-pin ISO 12098 Note on tractor operation: 12→24 V converter as well as ABS/EBS connection (ISO 7638) and power supply (e.g. ISO 1185/12098) required for the onboard hydraulics. Hydraulics (Ramps) 2 cylinders, including changeover valve for operation via the tractor's onboard hydraulics. Accessories (Selection) 2 toolboxes, 2 wheel chocks (metal), fire extinguisher box Reflectors (side white/yellow; extendable yellow/red), rectangular rear reflectors Lashing eyes: 7 per side + 6 on the platform (10 t per eye) Mud flaps (front/rear), hose/cable holders on the drawbar Paint Finish Sandblasting, 3× epoxy primer, 3× acrylic (≈ 230 µm), 1× acrylic clearcoat Warranty 2 years on frame structure and axles (excluding accidents/operator error) 2 years on electrical and braking systems (excluding wear parts such as brake pads, accidents/operator error) 1 year on paint finish (excluding accidents/operator error) Technical and pricing changes reserved. Images are for reference only and may show optional equipment.

Condition: used, maximum load weight: 31,000 kg, overall weight: 40,000 kg, axle configuration: > 3 axles, first registration: 07/2024, loading space length: 9,290 mm, loading space width: 2,520 mm, loading space height: 950 mm, * PT 40.0 Profi ----Brakes: * Wabco EBS-E (electronic braking system) * Emergency release system for spring brake cylinders * Drum brakes ----Axles: * 4 x 11-ton Gigant axles ----Suspension: * Air suspension with lifting and lowering system and rapid drop valve ----Drawbar: * Drawbar with 50 mm drawbar eye and height adjustment ----Lighting / Electrical: * EBS multi-voltage system with 12 & 24 V electrical system * 15-pole power connector * LED lighting system 12 / 24 V * LED rotating beacon (removable) at the rear * 2 LED reversing lights (switched via reverse gear) Nedpfel Tlhrsx Ak Djlc ----General attachments: * Manometer - pressure gauge for load weight determination (axles separated into 2 air suspension circuits) * Lateral impact guard * Swivel supports at the rear of the chassis frame * Mechanically adjustable warning sign packages at the front and rear * Front plastic quarter fenders with splash protection * Rear straight, galvanized steel splash guards with splash protection * Reflective contour strips on the sides and at the rear * Tool box made of galvanized steel sheet, black powder-coated, approx. 1,000 mm wide, 600 mm deep, 300 mm high ----Low-bed platform: * Extension in front of the turntable platform, approx. 490 mm long with 45° corners * ROBOTER welded anti-slip surface on the steel plate of the turntable platform * Hardwood flooring on the running surfaces of the low-bed platform ----Load securing (La-Si-package consisting of): * 1 x 13.4-ton UVV lashing eye on each side in front of the front bulkhead support * 4 holes on each side in the turntable platform, each with a lashing force of 2 tons * 1 pair of lashing eyes (13.4 tons) hanging at the rear on the left and right in front of the rear crossbeam * 4 pairs of UVV lashing rings (10 tons) on each side, swiveling and lowerable, loadable in all directions and recessed in the outer frame * 3 rung pockets on each side with simultaneous 2-ton lashing option ----Widening package: * Hot-dip galvanized mechanical folding outriggers for 3 m overall width (but not in the rear slope) * Beam holder for widening extensions under the chassis on the left in the longitudinal direction ----Excavator arm rest: * Excavator arm rest above the rear axle up to the end crossbeam, approx. 2,100 mm long and approx. 190 mm deep * 2 pairs of 6.4-ton lashing eyes on each side in the excavator arm rest ----Ramps: * Hydraulic, one-piece ramps (approx. 3,000 x 720 mm) mechanically adjustable on the sides * Outer beams of the ramps made of hardwood * Steel construction as preparation for a 6-way control valve ----Loading height: * Loading edge unladen approx. 950 mm +/- 20 mm ----Tires: * Tires 235/75 R 17.5 ----Paint: * Chassis, turntable, folding outriggers, mechanical support legs, ramps hot-dip galvanized * --Axles, air tanks, drawbar painted in a black tone-- ----Info: * Vehicle has a temporary registration in 07/2024, due to a missing tire pressure monitoring system and has not been loaded/used * New vehicle with manufacturer's warranty * Errors and prior sale are subject to change ----Delivery time: * Immediately available from Egestorf

Condition: new, empty load weight: 7,500 kg, maximum load weight: 32,500 kg, overall weight: 40,000 kg, axle configuration: > 3 axles, next inspection (TÜV): 03/2023, loading space length: 9,700 mm, loading space width: 3,000 mm, loading space height: 900 mm, suspension: air, tire size: 235/75r17,5, Year of construction: 2026, Equipment: ABS, center pivot plate, TOP FEATURES => INCLUDES THE FOLLOWING ACCESSORIES: Nledpfx Akeglbllj Doc Chassis frame hot-dip galvanized Storage box at the front on top of the platform, with hinged lid Storage box at the rear on top of the platform, with hinged lid Recess for excavator arm storage, low-bed area at the rear 3 m equipment package without slope Warning package for special permit Steel sheet toolbox Ladder support package in the outer frame Basic hydraulics for trucks with rear connection Hydraulic ramp lift for 1-piece ramps Hydraulic ramp adjustment, lateral Hydraulic support legs, left and right, 1 each 1 pair of lashing eyes, 6 tons, in the outer frame, bolted WABCO Smart Board, configured SSV complete, front left, HTD409525K COC, Certificate of Conformity OPTIONAL Rubber flooring on the ramp, €1890 net Rubber flooring on the slope, €1250 net Reversing drawbar, 40 / 50 DIN

Condition: used, maximum load weight: 31,000 kg, overall weight: 40,000 kg, axle configuration: > 3 axles, first registration: 07/2024, loading space length: 9,290 mm, loading space width: 2,520 mm, loading space height: 950 mm, * PT 40.0 Profi ----Brakes: * Wabco EBS-E (electronic braking system) * Emergency release system for spring brake cylinders * Drum brakes ----Axles: * 4 x 11 to. Gigant axles ----Suspension: * Air suspension with lifting and lowering system and rapid lowering valve ----Drawbar: * Drawbar with 50 mm drawbar eye and height adjustment ----Lighting / Electrical: * EBS multi-voltage system with 12 & 24 V electrical system * 15-pin electrical connector * LED lighting system 12 / 24 V * LED rotating beacon (removable) at the rear * 2 LED reversing lights (switched via reverse gear) ----General components: * Pressure gauge - pressure indicator for determining payload (axles separated into 2 air suspension circuits) * Side underrun protection * Swivel supports at the rear of the chassis frame * Mech. adjustable warning sign packages at the front and rear * Front plastic quarter fenders with splash guard * Rear straight, galvanized steel side skirts with splash guard * Reflective contour strip on the side and rear * Tool box made of galvanized steel sheet, black powder-coated, approx. 1,000 mm wide, 600 mm deep, 300 mm high ----Low-loader platform: * Extension in front of the turntable platform approx. 490 mm long with 45° corners * ROBOTER welded anti-slip coating on the steel plate of the turntable platform * Hardwood flooring on the running surfaces of the low-loader platform ----Load securing (La-Si package consisting of): * 1 x 13.4 to. UVV lashing eye to the left and right in front of the front bulkhead beam * 4 holes on each side in the turntable platform, each with a lashing force of 2 to. * 1 pair of lashing eyes (13.4 to.) hanging at the rear left and right in front of the rear beam * 4 pairs of UVV lashing rings (10 to.) on each side, swiveling and lowering, capable of withstanding loads in all directions and recessed in the outer frame * 3 rung pockets on each side with simultaneous 2 to. lashing option ----Widening package: * Hot-dip galvanized mech. folding outriggers for 3 m overall width (however, not in the rear slope) * Beam holder for widening under the chassis on the left in the longitudinal direction ----Excavator arm rest: * Excavator arm rest above the rear axle up to the end beam approx. 2,100 mm long and approx. 190 mm deep * 2 pairs of 6.4 to. lashing eyes on each side in the excavator arm rest ----Ramps: * Hydr. one-piece access ramps (approx. 3,000 x 720 mm) mech. adjustable on the side * Outer planks of the access ramps made of hardwood * Steel structure as preparation for a 6-way control valve ----Loading height: Nljdpfx Ael Tnu Aok Dsc * Unladen loading edge approx. 950 mm +/+ 20 mm ----Tires: * Tires 235/75 R 17.5 ----Paintwork: * Chassis, turntable, folding outriggers, mech. support legs, access ramps hot-dip galvanized * Axles, air tank, drawbar painted in a black tone ----Information: * Vehicle has a day registration in 07/2024, due to the missing tire pressure monitoring system and has not been loaded/used * New vehicle with manufacturer's warranty * Errors and prior sale reserved ----Delivery time: * Available for immediate delivery from Egestorf