Low loader trailer

MÜLLER-MITTELTAL T4 40,0 , Agrar, hydr. Rampen,3 m. Paket

Condition: new, maximum load weight: 31,630 kg, overall weight: 40,000 kg, axle configuration: > 3 axles, loading space length: 9,250 mm, loading space width: 2,520 mm, Year of construction: 2026, * T 4: * EBS * Emergency release system for spring accumulators * Drum brakes * 4 x 11 to. Gigant axles * Parabolic springs * Mech. axle compensation front and rear * Tire pressure monitoring with display option in the truck via EBS signal - without truck-side installation * Warning sign packages front & rear * Reflective contour striping on the sides and rear * EBS multi-voltage system for 12 & 24 V electrical systems * LED rotating beacon (removable) at the rear * 24 V - 15-pin and additionally 12 V - 7+4 pin power cable * Extended connection cables for agricultural and forestry tractors * LED lighting * Straight drawbar with 40 mm drawbar eye and stepless height adjustment * Toolbox made of powder-coated sheet steel and spare wheel holder in body design, located on the right side * Front, closed, plastic single mudguards * Rear, straight steel mud flaps each with splash protection (spray mist suppression) * Side underrun protection * Extended offset crank extended by 500 mm to the front * Extension of the turntable platform by 520 mm with 45° corners and 3 recessed storage compartments incl. lid and lockable * Chassis made of high-strength fine-grain steel * Floor over the turntable platform made of 50 mm and in the low-bed platform made of 60 mm needle wood * Outer planks of the ramps made of 50 mm bamboo wood * 4 pocket sleeves on each side (but no stanchions present) with simultaneous 2 to. lashing capability * Lasi package consisting of: 2 lashing eyes 6.4 to. at the front left and right on the main frame of the turntable platform, 1 pair of 13.4 to. lashing rings on the outer frame on the front and rear sides, and 4 pairs of 10 to. lashing rings on each side, pivotable and lowerable, loadable in all directions and embedded in the outer frame, 2 pairs of lashing rings 6.4 to. on each side in the excavator arm rest, 8 pairs of galvanized folding outriggers for 3 m total width (but not in the rear slope) * Extension planks stored on the left side in a storage compartment * Excavator arm rest above the rear axle to the end of the approach ramp approx. 2,300 x 740 x 190 mm * Mech. support legs at the rear * Hydr. hot-dip galvanized ramps approx. 3,000 x 720 mm Godsrczm Djpfx Altsbn * Hydr. lateral ramp displacement on sliding tube from the ramp shaft * Loading area above the slewing ring: approx. 2,990 x 2,520 mm * Rear loading area: approx. 6,280 x 2,520 mm * Loading height loaded approx. 860 mm (incl. 860 mm approach ramp) * Chassis, turntable, ramps, mech. folding supports at the rear hot-dip galvanized * Axles, springs, air tanks and slewing ring painted in a black tone * New vehicle with manufacturer's warranty * Errors and prior sale reserved * Immediately available from Egestorf

Condition: new, functionality: fully functional, empty load weight: 7,500 kg, maximum load weight: 36,500 kg, overall weight: 44,000 kg, axle configuration: > 3 axles, loading space length: 9,190 mm, loading space width: 2,540 mm, loading space height: 900 mm, suspension: steel-air, tire size: 235×75 R17,5, wheelbase: 1,310 mm, Year of construction: 2024, Equipment: ABS, center pivot plate, CETRATEK 4-Axle Low Loader TL89.4 (EU-COC) Short Description Robust low loader for heavy machinery transport. Frame made of high-strength ST-52/S355, optionally fine-grain steel S700. Ramps with 20 t load capacity each, mechanically or hydraulically foldable without loss of capacity. Optionally available as a low-bed trailer; loading height in wheel recess area can be reduced from approx. 900 mm to approx. 500 mm. Dimensions / Configuration Total length: 11,914 mm, total height: 3,775 mm (over ramps) Platform: gooseneck 2,440 mm + loading area 6,750 mm Width: 2,540 mm (+ 250 mm manual extension on each side) Coupling → 1st axle: 2,767 mm; → 2nd/3rd axle: 6,136 mm Axle spacings: front 1,310 mm, rear 1,360 mm Platform height: 900 mm (low-bed approx. 500 mm), track width 1,850 mm Rear ramps: 3,000 × 750 mm, laterally adjustable, 20 t per ramp Drawbar height: 400–900 mm; turntable Ø 110 (CYR) Floor: steel + 45 mm hornbeam hardwood, protective lacquer coating Weights / Capacity a) GVW 44,000 kg → payload approx. 36,500 kg* b) On-road 24,000 kg → payload approx. 16,500 kg * Version a) subject to special approval according to §70 StVZO; certification/DEKRA inspection at extra cost. Towing eye Ø 50 mm (optional Ø 40 mm), unladen weight approx. 7,500 kg Rear supports: manual (hydraulic optional) Gbodpfxsu Rbzve Altsn Steel Structure / Chassis Welding qualification TS EN ISO 9606-1, processes TS EN ISO 4063, shielding gases TS EN ISO 14175 4 × 11 t axles (TRAX), tires 235/75 R17.5 (16 units, PETLAS or equivalent; Continental/Michelin on request at extra cost), rims 6.75×17.5, air suspension, max. 100 km/h permitted Brakes / Electrics WABCO EBS 4S/2M, brake pads 330×200, air tanks 2×80 L + 1×60 L Brake cylinders: 4× Type 24 + 4× Type 24/30, levers 165 mm Voltage 24 V (24 V converter required for 12 V towing vehicle) Side reflectors: 4× LED per side + 2× white front reflectors, taillights 2× LED, 2× triangular reflectors Connections: 7-pin EBS ISO 7638, 7-pin ISO 1185/3731, 15-pin ISO 12098 Note on tractor operation: 12→24 V converter as well as ABS/EBS connection (ISO 7638) and power supply (e.g. ISO 1185/12098) required for the onboard hydraulics. Hydraulics (Ramps) 2 cylinders, including changeover valve for operation via the tractor's onboard hydraulics. Accessories (Selection) 2 toolboxes, 2 wheel chocks (metal), fire extinguisher box Reflectors (side white/yellow; extendable yellow/red), rectangular rear reflectors Lashing eyes: 7 per side + 6 on the platform (10 t per eye) Mud flaps (front/rear), hose/cable holders on the drawbar Paint Finish Sandblasting, 3× epoxy primer, 3× acrylic (≈ 230 µm), 1× acrylic clearcoat Warranty 2 years on frame structure and axles (excluding accidents/operator error) 2 years on electrical and braking systems (excluding wear parts such as brake pads, accidents/operator error) 1 year on paint finish (excluding accidents/operator error) Technical and pricing changes reserved. Images are for reference only and may show optional equipment.

Condition: new, empty load weight: 7,500 kg, maximum load weight: 32,500 kg, overall weight: 40,000 kg, axle configuration: > 3 axles, next inspection (TÜV): 03/2023, loading space length: 9,700 mm, loading space width: 3,000 mm, loading space height: 900 mm, suspension: air, tire size: 235/75r17,5, Year of construction: 2026, Equipment: ABS, center pivot plate, TOP EQUIPMENT => INCLUDING THE FOLLOWING ACCESSORIES: Hot-dip galvanized chassis frame Storage box at the top front of the plateau, with hinged lid Rear storage box at the top of the plateau, with hinged lid Trough for excavator stick storage, rear low bed area Gjdpfxjglblls Altebn 3 m equipment package without slope Warning package for special permit Sheet steel tool box Stake pocket package in outer frame Basic hydraulics for trucks with rear connection Hydraulic ramp lift for 1-piece ramps Hydraulic lateral ramp displacement Hydraulic support legs left and right 1 1 pair of lashing eyes 6 tons in the outer frame, bolted WABCO-Smart Board conf. SSV cpl. front left HTD409525K COC COC paper OPTIONAL Rubber floor on the ramp 1890€ net Rubber floor on the slope 1250€ net Reversible drawbar 40 / 50 DIN