Low loader trailer

MÜLLER-MITTELTAL 2 achs Tandem Stahl 3 Seitenkip. mit Kombiklappe

Condition: used, maximum load weight: 10,870 kg, overall weight: 14,400 kg, axle configuration: 2 axles, first registration: 06/2025, loading space length: 5,000 mm, loading space width: 2,420 mm, loading space height: 500 mm, Year of construction: 2023, Equipment: ABS, KA-TA-R 14.4: ----Brakes: * Wabco ABS * Emergency release system for spring-loaded cylinders * Drum brakes ----Axles: * 2 x 7 t Gigant axles ----Suspension: Hnedpel Th Htjfx Aaiel * Parabolic springs with tandem compensation unit ----Drawbar / Flange Drawbar Eye: * Height-adjustable drawbar (up to 300 mm) with 40 mm flange drawbar eye ----Electrics / Lighting: * 15-pin electrical connector * Multi-chamber taillights ----General Attachments: * Jost mechanical landing gear at the front * 2 mechanical folding supports at the rear * Plastic toolbox approx. 650 x 350 x 320 mm, mounted front right side of chassis * Bolted underrun protection * Plastic quarter mudguards * Net hooks located at each central locking bearing and two at the front wall ----Chassis: * Chassis made from fine-grain steel ----Tipper Body: * Steel pallet 3-way tipper body with continuous side walls, upper internal tube reinforcement, fold-down without centre posts, with drop side spring lift assist * Rear corner posts bolted * Combination steel wing-door rear wall, 2-leaf, asymmetrical split, can be swung and locked up to 270°, not foldable, equipped with additional swing frame for automatic rear wall opening when tipping. Locking via galvanised rotary latch at rear and central locking. Deactivation function for the automatic rear wall operation when tipping backwards with one leaf open. * 4 mm floor plate made of fine-grain steel * Rear guide rail for loading ramps ----Load Securing: * One 5 t lashing ring fitted in each corner, plus four 3 t lashing points recessed into the outer frame on each side ----Ramps: * One pair of aluminium loading ramps, approx. 3,570 x 410 mm (load capacity 10 t/pair), suitable for rubber-tyred and tracked vehicles * Lockable compartment at the rear, recessed below the loading floor in the chassis, for the ramps ----Tyres: * Tyres 285/70 R 19.5 ----Paintwork: * Chassis, drawbar, underrun protection, rear posts, rear folding supports hot-dip galvanised * Axles, springs, air tanks, and landing gear painted in black tone * Drop side panels painted in RAL 9010 pure white * Side walls paintable in any RAL colour (at extra charge) ----Info: * Reinforced structure with load securing certificate * Vehicle has a daily registration (unused) * Errors and prior sale excepted ----Delivery Time: Immediately available ex Egestorf

Condition: new, functionality: fully functional, Year of construction: 2025, color: grey-black, overall weight: 2,500 kg, maximum load weight: 3,000 kg, empty load weight: 3,000 kg, loading space width: 3,000 mm, loading space length: 7,000 mm, loading space height: 2,500 mm, machine/vehicle number: Wohncontainer, Office Container | Residential Container | Construction Container | Model FOREST | 300cm x 700cm | High-Quality and Flexible Solution Available products can be viewed in our warehouse and picked up directly. Our office and residential containers provide an excellent solution for a wide range of applications. They are characterized by outstanding quality, maximum flexibility, and short delivery times. Technical Details: • Dimensions: 300 x 700 x 250 cm • Weight: 1950 kg Insulation: • Facade cladding with wood-look panels • Ceiling/walls: 5 cm PUR (Polyurethane) • Special, highly robust floor chassis • 2 mm galvanized steel sheet • Rock wool insulation between panels • Optional: 10 cm insulation with PUR, PIR, or rock wool • Floor: 16 mm fiber cement board + PVC covering Equipment: • 1x room • 1x full-height glazed front facade • 2x sliding windows • 1x double glass door Hnedswycdlopfx Aaisl • 1x wood-look facade cladding Colors: • RAL7016 & wood-look facade cladding High-quality workmanship for long-term use Stock & Delivery: • In stock: same-day shipping • Not in stock: production time depending on model 2–4 weeks • Worldwide shipping: professional shipping to all countries • Custom sizes: products can be manufactured according to customer requirements Showroom Address: Im Mannenberg 9a, 53557 Bad Hönningen For further information or tailored modifications, we are happy to assist you!

Condition: new, maximum load weight: 7,500 kg, overall weight: 10,500 kg, axle configuration: 2 axles, loading space length: 5,035 mm, loading space width: 2,420 mm, loading space height: 500 mm, total width: 2,550 mm, total height: 1,475 mm, Year of construction: 2026, Equipment: ABS, * Humbaur Three-Way Tipper * HTK 10 50 24 * Year of manufacture: 2026 * Gross weight: 10,500 kg * Payload: 7,500 kg * Unladen weight: 3,000 kg * Overall dimensions: 6960 x 2550 x 1475 mm * Platform dimensions: 5035 x 2420 x 500 mm * Steel side panels: 500 mm high * Continuously height-adjustable drawbar * 10 recessed lashing rings * 2 rear supports * Electrical and pneumatic connections at the drawbar * Storage compartment with 2 aluminium loading ramps integrated into the chassis frame * 8t loading ramps surcharge: €1,499 IMPORTANT! PLEASE READ! We explicitly reserve the right of prior sale since this item is also offered on other platforms. We strongly recommend viewing and inspecting the trailer to avoid any misunderstandings regarding its condition or suitability. Inspections are possible at any time by appointment and are expressly encouraged! Images are for reference only and may show optional accessories for an additional charge. The interior dimensions given are approximate. TRADE-INS POSSIBLE FOR ALMOST ANYTHING! PART EXCHANGE AND ADDITIONAL PAYMENT POSSIBLE! Exhibition grounds: 58285 Gevelsberg, Am Sinnerhoop 17 Opening hours: Monday–Friday 8:30 am–5:00 pm, Saturday 8:30 am–2:00 pm Always over 500 new and used trailers in stock! Hnedpfx Ajqnrtasaiol Pegasus Anhänger GmbH Am Sinnerhoop 17 58285 Gevelsberg Tel.: Fax:

Condition: new, maximum load weight: 5,600 kg, overall weight: 7,500 kg, axle configuration: 2 axles, loading space length: 4,000 mm, loading space width: 2,030 mm, loading space height: 400 mm, total width: 2,200 mm, total height: 1,400 mm, Year of construction: 2026, * Humbaur HTK 754020 * Three-way tipper trailer * New vehicle * Tandem axle * Year of manufacture: 2025 Hnodottfm Hepfx Aaiel * Gross vehicle weight: 7,500 kg * Unladen weight: 1,900 kg * Payload: 5,600 kg * Overall dimensions: 6040 mm x 2200 mm x 1400 mm * Internal dimensions: 4000 mm x 2030 mm x 400 mm * Loading height: 920 mm * Steel side and rear walls fold-down and removable * Rear wall pendular with central locking * Height-adjustable drawbar approx. 590 mm - 930 mm * Torsion bar axles and parabolic suspension * Integrated slot for loading ramps * 4-stage telescopic cylinder * Single-circuit hydraulic connection * Floor plate made from 4 mm steel sheet * 3 pairs of recessed lashing points * Air brake system with ALB / ABS ATTENTION !!!!! PLEASE READ CAREFULLY !!!!! We expressly reserve the right to prior sale, as this item is also offered on other platforms. We strongly recommend an inspection and assessment to avoid misunderstandings regarding condition and suitability for the buyer. Inspections and assessments are possible at any time by appointment and are expressly encouraged!!! Images for illustration only; may include accessories subject to additional charges. The above-stated internal dimensions are approximate. For new vehicles, additional costs for freight and documentation may apply. TRADE-INS POSSIBLE FOR ALMOST ANYTHING!!! EXCHANGE DEALS AND TOP-UP PAYMENTS POSSIBLE!!! Exhibition grounds: 58285 Gevelsberg, Am Sinnerhoop 17 Opening hours: Monday to Friday 8:30 am to 5:00 pm, Saturday 8:30 am to 2:00 pm Always over 500 new and used trailers in stock!!! Pegasus Anhänger GmbH Am Sinnerhoop 17 58285 Gevelsberg Tel.: Fax:

Condition: new, machine/vehicle number: ebf3f771e96394cd89e56bbb7, overall weight: 11,800 kg, axle configuration: 2 axles, tire size: 235 / 75 r 17,5, Further information Chassis central axle trailer Welded fine-grained steel construction 6 pairs of lashing eyes bolted to the outside of the floor/outer frame, 5 tons each 2 pairs of lashing eyes additionally bolted to the floor, 5 tons each in the corners Gear support foot at the front Folding rear support 2 wheel chocks with holder Steel underride guard Rear spray flaps across the entire width Quarter-shell mudguards 1 plastic tool box, with shelf, w=620/h=360/t=440 mm, lockable with a padlock. (lock not included in scope of delivery) Towing device central axle trailer Towing bar with tested 40 mm towing eye Height-adjustable drawbar via spindle, max. adjustment range 300 mm Axles + suspension Drum brake axles, manufacturer's choice Axle/chassis laser-measured Reduction in tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation (rocker compensation) Wheels and tires 235 / 75 R 17,5 manufacturer's choice Factory silver steel rims Brake system 2-line compressed air brake system Hand spindle parking brake Integral air reservoir 2 non-interchangeable coupling heads at the front, with connecting cables to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin interchangeable plugs at the front, with connecting cable, Floor Steel/ checker plate floor for high point load capacity Note: Slight floor corrugation possible due to welding distortion! Platform length approx. 5,200 mm Rear sloping to approx. 900 mm Hsdpfei Rixrsx Aaijnl Front wall / front corner stanchions 25 mm aluminum hollow profile, 400 mm high, Drop sides 25 mm aluminum hollow profile, 400 mm high, foldable and removable Rear wall / rear corner stanchions 1 pair of steel stanchions attached to the frame and with bracket for locking the drive-on ramps, drive-in width approx. 2,430 mm Drive-on ramps 2 steel ramps 2,300 mm long, 510 mm wide, can be moved sidewayswith grab handle on the ramps covered with 3 toothed steel rails With gas pressure jack for one-man operation Country of registration/plates Country of registration: Germany 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white on the sides and red on the rear Paintwork Hot-dip galvanized frame incl. passivation 15-year warranty against rusting through Front wall aluminum Side wall anodized aluminium Drive-on ramps Hot-dip galvanized Attention! These are archive pictures.

Condition: new, empty load weight: 9,650 kg, maximum load weight: 30,350 kg, overall weight: 40,000 kg, axle configuration: > 3 axles, loading space length: 9,740 mm, loading space width: 2,550 mm, suspension: air, tire size: 235/75 r17,5 zoll, Year of construction: 2026, Equipment: ABS, center pivot plate, 4-AXLE LOWBED TRAILER WITH TOP-SPEC EQUIPMENT! => HOT-DIP GALVANIZED (CHASSIS FRAME, BOGIE FRAME, ACCESS RAMPS) => FULL AIR SUSPENSION => WITH LIFTING AND LOWERING FUNCTION (REAR AXLE MODULE!) => SAF LOWBED AXLES => LASHING PACKAGE => OUTER FRAME WITH PERFORATIONS FOR ADDITIONAL LASHING POINTS Hodpfx Aaohvxgzjisnl => CLEAT STRIPS AT REAR OF ACCESS SLOPE => 6 LASHING POINTS IN THE EXCAVATOR ARM TROUGH AT THE REAR => LONG ONE-PIECE ACCESS RAMPS => LOW APPROACH ANGLE Permissible gross weight: 40,000 kg Payload approx. 30,350 kg Chassis frame hot-dip galvanized Bogie frame hot-dip galvanized Access ramps hot-dip galvanized Air suspension SAF axle with drum brakes EBS electronic braking system Tyres: 235/75R17.5 – 16 units Lowbed length approx. 7,160 mm Trough for excavator arm resting, approx. 3,000 x 730 x 180 mm at rear of lowbed 4 pairs of 10-ton recessed lashing rings in lowbed 2 pairs of 10-ton recessed lashing rings in raised deck 4 pairs of 3-ton lashing points on outer frame of lowbed 3 pairs of 6-ton lashing eyes on outer frame 4 pairs of stake pockets in outer frame of raised deck 4 pairs of stake pockets in outer frame of lowbed 3-meter widening kit with folding outriggers (flat, no slope) 4 x warning panels with lights Rotating beacon at rear LARGE STEEL STORAGE BOX under the loading area 2 storage compartments with hinged lids in raised deck Hydraulic ramp lifters 1-piece ramps, approx. 3,150 x 750 mm Softwood floor on loading area and ramps 40,000 kg GVW only with special permit as per Section 70 => Delivery freight costs: €2.90 plus VAT per km => Prices ex works D-86368 Gersthofen Your direct contact: Mr. Hauptmann Tel. DOLL Fahrzeugbau *Subject to prior sale and modifications!* *Price valid ex works D-86368 Gersthofen* *Sale to commercial customers only!* *Images may differ and are for general guidance only — may show/accessorise options available at extra cost*

Condition: as good as new (ex-display), empty load weight: 10,000 kg, maximum load weight: 30,000 kg, overall weight: 40,000 kg, axle configuration: 4x2, loading space length: 9,220 mm, loading space width: 2,540 mm, suspension: air, tire size: 235/75 R17,5, Year of construction: 2025, Equipment: ABS, center pivot plate, trailer coupling, HTD 40K-RM-BM_ Internal dimensions: approx. 9,220 mm x 2,540 mm Overall dimensions: approx. 11,300 mm x 2,540 mm x 3,850 mm Perm. total weight: 24,000 kg Payload: approx. 14,000 kg Tyres: 235/75R17.5 inches Loading height: approx. 900 mm Drawbar length: approx. 1,500 mm Coupling height: approx. 820–1,000 mm Ramp angle: approx. 10° Ramp length: approx. 3,150 mm Ramp width: approx. 750 mm Perm. total weight special equipment: 40,000 kg Payload special equipment: approx. 30,000 kg Low-bed length: approx. 6,610 mm Overall dimensions (LxWxH): 11,200 Technical total weight: approx. 44,000 kg Technical axle load: approx. 11,000 kg 6 pairs of lashing points, 3,000 kg each Lashing points in the low-bed outer frame 4 pairs of lashing points, 3,000 kg each Lashing/pocket sleeves 3 t in the high-bed outer frame 1 pair of lashing points, 3,000 kg each Lashing/pocket sleeves 3 t in the low-bed outer frame Suspension: Air suspension unit including lifting and lowering acting on the rear axle unit Brake system: Brake system according to EC directives with EBS 4S/3M in multivoltage version (12–24V), spring-loaded parking brake including two external test ports for brake/modulator and bellows pressure Electrics: LED lighting with indicator function for side marker lights, multivoltage (12–24V) Turntable: Heavy-duty welded construction with low-maintenance ball-bearing turntable Towing equipment: Cranked drawbar with 50 mm towing eye, low-maintenance silent bushings including height adjustment for drawbar Chassis: Heavy-duty welded construction made of high-tensile fine-grained steel, through-running cross-members for maximum stability Wheel recesses front (approx. 2,500 mm upper length, 410 mm depth) and rear (approx. 1,470 mm upper length, 370 mm depth); without wheel recess covers Excavator trough (length 1,650 mm, width 750 mm, depth 190 mm) Wheel cutouts above the rear wheels with 2,010 mm wheelbase, front corners chamfered, rear with climbing strips on ramp incline for maximum safety during loading and unloading 4 pairs of stake pockets (90x50 mm) on high-bed outer frame 1 pair of stake pockets (90x50 mm) on low-bed outer frame Floor: 50 mm softwood flooring (painted/impregnated) Ramps: One-piece hot-dip galvanized loading ramps (3,150 mm x 750 mm) with 50 mm softwood covering (painted/impregnated), laterally adjustable, direct-acting upright spring-assist for easiest handling Finish: Chassis frame hot-dip galvanized in immersion bath Support: 2 foldable supports at the rear left and right of the vehicle Equipment: Folding side underrun protection Front semi-circular plastic mudguards; rear straight steel mudguards with anti-spray 2 wheel chocks with holders; contour markings according to ECE regulation R48 Hjdpfjiciutex Aaionl Front wheel recess cover: With 3 pairs of stake pockets, without covering (cover retractable under the longitudinal beams) 975.00888 Hardwood covering for front wheel recess cover Rear wheel recess cover: With 1 pair of stake pockets, without covering (cover retractable under the longitudinal beams) 975.00897 Hardwood covering for rear wheel recess cover 3 pairs of bolted lashing eyes, 6 t 3 m equipment package without incline B=11,200 Folding outriggers with softwood boards 970.04199-36 LED warning package HTD, cranked Aspöck warning boards 4 times, electrics and revolving beacon 1 pair of storage compartments for 3 m wood planks package (2 pieces mounted lengthwise under the loading area in front of the wheel recess) Rubber coat

Condition: used, maximum load weight: 8,750 kg, overall weight: 11,900 kg, axle configuration: 2 axles, first registration: 06/2024, total width: 2,550 mm, Year of construction: 2023, Müller Mitteltal KA-TA-R 11.9 tandem 3-way tipper with lots of extras. Total weight: 11,900kg Standard payload approx.: 8,750kg Clear dimensions: 5,000x2,420x500mm Tires: 385/55R19.5 4-layer paintwork, single color Wheels: silver Chassis/underbody protection: hot-dip galvanized Platform with bulkhead: hot-dip galvanized Axles/springs/fuel tank etc.: black Side and rear wall: RAL 2011 deep orange Reinforced and certified structure in accordance with EN 12642 XL including load securing certificate. (Only in conjunction with 500mm high steel side walls). Rear stanchions screwed, hot-dip galvanized, without top coat. Lashing points LC 5,000 daN recessed at the front. Net hooks integrated at the side and rear in the bearings of the central locking system to the base side wall and 2 additional pieces on the front wall. BPW axles instead of GIANT tipping platform with permanently attached front wall in hot-dip galvanized design, with screwed, galvanized rear stanchions, without additional coating (not with HARDOX floor). Due to the system, the formation of waves during hot-dip galvanization, especially with the large floor panel, cannot be ruled out; complaints in this regard are excluded from the warranty. Tires 385/55R19.5 instead of 235/75R17.5 (floor and coupling height + approx. 110 mm, Code 08.940 ramp length 3,570 mm required). 1 plastic tool box, black, lockable, W=750xH=350xD=300mm (45kg payload with even load), arrangement: on the chassis frame on the right in the direction of travel. 1 pair of aluminum docking ramps without fairway (8 t/pair), 3,570x400x105mm, suitable for rubber-tired and tracked vehicles, 55 kg/each. Two-step access in front of the front wall, on the left in the direction of travel (hot-dip galvanized). Extended connecting lines for agricultural and forestry tractors. Hnsdpsvy Tvtsfx Aaisl Further information New: No

Condition: used, machine/vehicle number: GE11/142/2022, empty load weight: 6,350 kg, maximum load weight: 17,650 kg, overall weight: 24,000 kg, axle configuration: 3 axles, first registration: 08/2008, loading space length: 8,500 mm, loading space width: 2,500 mm, suspension: air, Very well-maintained vehicle from first owner Three-axle low-loader trailer Low-loader with drive-up ramp Heavy-duty transport Model T3 Komakt 30.0 Length 8,500 mm Width 2,500 mm Air suspension Commercial/export net price – €15,990 Subject to changes, interim sale, and errors Hnjdpfjn Aw Hkjx Aaijl ===== Phone2 Mobile =====

Condition: new, empty load weight: 907 kg, maximum load weight: 2,130 kg, overall weight: 3,000 kg, axle configuration: 2 axles, loading space length: 3,140 mm, loading space width: 1,750 mm, loading space height: 350 mm, loading space volume: 2.2 m³, color: other, construction height: 1,260 mm, working width: 1,930 mm, Manufacturer: Humbaur Type: 3-sided tipper HTK Alu 3000.31 Perm. total weight: 3000 kg Weight: 3000 kg Payload: 2130 kg Unladen weight: 870 kg Box dimensions: 3140 x 1750 x 350 mm Tires: 13 inch Loading height: 750 mm Loading area hydraulically tiltable with hand pump and electric pump Tipping angle rear 42, side 50 with leaf grid attachment/steel grid attachment 600 mm high, 4-sided swinging - V-drawbar hot-dip galvanized - Chassis and tipper body hot-dip galvanized - Tipper body made of steel, made from one piece - 4-stage hard-chrome plated tipping cylinder - Hand pump, from 3000 kg perm. weight electric pump with hand pump, from 3000 kg perm. weight electric pump with hand pump, from 3000 kg perm. weight electric pump with hand pump. electric pump with hand pump - 13-pin plug and reversing light - 350 mm high aluminum drop sides, completely removable - rear flap can be swivelled - 6 tie-down rings mounted on the bridge floor, tensile force 800 kg per tie-down ring, Dekra tested - jockey wheel - plank shaft as preparation for aluminum planks for easy retrofitting Price incl. Vehicle registration certificate (registration certificate part II and COC papers) We have a large number of trailers from the following manufacturers in stock: Brenderup Humbaur Hapert Brian James Trailers Unsinn and Neptun On request, we can provide you with a free transfer license plate. We repair trailers from all manufacturers. Further accessories on request. Technical changes, price changes and errors excepted. No liability is assumed for errors and misprints.automatic reverse drive, rubber spring axle, independent suspension, tiltable loading area, support wheel, marker lights, chassis and tipper body hot-dip galvanized, braked, incl. warranty, V-drawbar hot-dip galvanized, tipper body made of steel, made of one piece, 4-stage hard-chrome-plated tipping cylinder, hand pump, from 3000 kg permissible total weight, electric pump with hand pump. Electric pump with hand pump, 13-pin plug and reversing light, 350 mm high aluminum drop sides, completely removable, rear flap can be swivelled, 6 tie-down rings mounted on the bridge floor, tractive force 800 kg per tie-down ring, Dekra tested, plank shaft as preparation for aluminum planks for easy retrofitting Hjdpfx Aektm Suoaienl