Used Müller-Mitteltal Roll-Off Trailers for sale (255)

Condition: new, maximum load weight: 6,870 kg, overall weight: 9,900 kg, axle configuration: 1 axle, Year of construction: 2026, * KWH 9.9 ML: ----Brakes: * EBS braking system * Drum brake * Emergency release device for spring accumulators ----Axle: * BPW axle Guedpfx Amsu I Iqfo Toi ----Suspension: * Parabolic springs ----Drawbar / Flange coupling: * Drawbar with 40 mm screwed coupling (height adjustable mm) ----Electrical system / Lighting: * 15-pole power connector * LED lighting * Flashing LED side marker lights * TPMS tire pressure monitoring system ----General components: * Front support winch * Spring-supported square tube supports at the rear with base plate, safety locking pins for different support heights * Closed fenders made of sheet steel with splash protection * Closed side impact protection, usable as an advertising surface * Plastic toolbox with bottom insert (horizontal installation), approx. 500 x 350 x 400 mm ----Superstructure: * Swiveling cable reel superstructure, width between the reel arms 1,700 mm, with a tensioning mechanism to secure the reel at the ends of the support arms and a locking mechanism for the cable reel superstructure to the chassis via a centrally arranged claw lock * Motor-hydraulic drum drive with oil motor * Valves and sliding rubber-coated drive rollers * Hydraulic speed control and brake for the drum drive * Steel drum shaft with 76 mm diameter, centering, and rotatable ends * 1 pair of centering cones made of polyamide, stepped ----Chassis: * Chassis made of torsion-resistant square tubes and cross members ----Pump unit: * Pump unit, hydraulically driven with Loncin gasoline engine, including manual and electric starter * Fuel tank and manual starter * 13 hp with gear pump (150 bar) ----Tires: * 315/80 R 22.5 ----Unladen weight: * 2,690 kg unladen weight ----Paint finish: * Vehicle is hot-dip galvanized ----Information: * New vehicle with full manufacturer's warranty * Errors and prior sale excepted ----Delivery time: * Available from approx. week 49/2026

Condition: new, maximum load weight: 6,870 kg, overall weight: 9,900 kg, axle configuration: 1 axle, Year of construction: 2026, * KWH 9.9 ML: ----Brakes: * EBS braking system * Drum brake * Emergency release device for spring-loaded cylinders ----Axle: * BPW axle ----Suspension: * Parabolic springs ----Drawbar / Flange coupling: * Drawbar with 40 mm bolted coupling (height-adjustable, mm) ----Electrical system / Lighting: * 15-pin power connector * LED lighting * Flashing LED side marker lights * TPMS tire pressure monitoring system ----General components: * Front support jacks * Spring-supported square tube supports at the rear with base plate, safety locking pins for various support heights * Enclosed fenders made of sheet steel with splash guard * Enclosed side impact protection, can be used as an advertising space * Plastic toolbox with base insert (horizontal installation), approx. 500 x 350 x 400 mm ----Superstructure: * Swivel cable drum superstructure, inner width between the drum arms 1,700 mm, with tensioning closure for securing the drum at the ends of the support arms, and a locking mechanism for the cable drum superstructure and the chassis via a centrally arranged claw lock * Motor-hydraulic drum drive with oil motor * Valves and sliding, rubber-coated drive rollers * Hydraulic speed control and brake for drum drive * Steel drum shaft with 76 mm diameter, with centering and rotatable ends * 1 pair of centering cones made of polyamide, stepped offset ----Chassis: * Chassis made of torsion-resistant square tubes and crossmembers ----Pump unit: * Hydraulic pump unit with Loncin gasoline engine including manual and electric starter * Fuel tank and manual starter * 13 hp with gear pump (150 bar) ----Tires: * 315/80 R 22.5 ----Unladen weight: * 2,690 kg unladen weight ----Painting: Gedpfxeu I Iqro Am Tjui * Vehicle is hot-dip galvanized ----Information: * New vehicle with full manufacturer's warranty * Subject to errors and prior sale ----Delivery time: * Available from approximately week 49/2026

Condition: new, suspension: other, color: other, gearing type: other, driver cabin: other, emission class: none, Leveling bracket for low-loader semi-trailer including container closures, price per leveling bracket, , --  Subject to printing errors, mistakes and changes, sample images --, More information at: !, More details: ! Godpj Aihgcefx Am Toui

Condition: new, maximum load weight: 23,940 kg, overall weight: 30,000 kg, axle configuration: 3 axles, loading space length: 8,460 mm, loading space width: 2,520 mm, Year of construction: 2026, * T3 Profi 30.0 ----Brakes: * EBS braking system * Emergency release system for spring brake cylinders * Drum brakes ----Axles: * 3 x 11-ton Gigant axles ----Suspension: * Parabolic springs with mechanical axle compensation at the rear ----Drawbar: * Drawbar with 50 mm drawbar eye and height adjustment via coil spring & tension lock ----Lighting / Electrical System: * TPMS tire pressure monitoring system * Multi-voltage system * LED tail lights 12 / 24 V * Rotating beacon (removable) at the rear * 15-pin power connector ----General Components: * Side impact protection * Swivel supports at the rear on the chassis frame * Mechanically adjustable warning sign packages at the front and rear * Front mudguards made of plastic and rear mudguards made of straight, galvanized steel sheet, each with splash protection * Tool box made of galvanized steel sheet - black powder-coated - approx. 650 x 300 x 600 mm * Hinged lid (hot-dip galvanized) for the tool box in the turntable platform * 4 lashing points on each side (but no lashing bars included) with simultaneous lashing capability ----Load Securing (La-Si package consisting of): * 2 lashing points (6.4 tons) at the front left & right on the main frame of the turntable platform * 6 pairs of UVV lashing rings, swivel and lowerable, loadable in all directions and recessed in the outer frame * 13.4 tons in the corners, otherwise 10 tons ----Widening: * 6 pairs of mechanical folding outriggers for a total width of 3 meters (but not in the rear slope), * Widening boards placed in the middle of the loading area ----Ramps: * Hot-dip galvanized, one-piece hydraulic ramps (approx. 3,000 x 720 mm), mechanically adjustable on the side * 4-way control block for retrofitting of the hydraulic side ramp adjustment ----Loading Area: * above the turntable: approx. 1,960 x 2,520 mm & unladen approx. 1,070 mm * rear loading area: approx. 6,500 x 2,520 mm & unladen approx. 910 mm (incl. 860 mm approach angle) ----Tires: * 235/75 R 17.5 twin tires ----Unladen Weight: Guodpfxsl Th I As Am Tji * approx. 5,980 kg unladen weight ----Painting: * Chassis, turntable, drawbar and ramps hot-dip galvanized * Axles, springs, air tanks etc. painted in a black shade ----Information: * Technically possible gross vehicle weight of 30,000 kg * New vehicle with manufacturer's warranty * Errors and prior sale excepted ----Delivery time: * Immediately available from Egestorf

Condition: new, maximum load weight: 10,900 kg, overall weight: 14,400 kg, axle configuration: 2 axles, loading space length: 5,000 mm, loading space width: 2,420 mm, loading space height: 500 mm, Year of construction: 2026, * KA-TA-R 14.4 ----Brakes: * Wabco EBS * Emergency release system for spring brake cylinders * Drum brakes ----Axles: * 2 x 7 tons Gigant axles ----Suspension: * Parabolic springs with tandem equalizer ----Drawbar / Flange coupling: * Height-adjustable, hot-dip galvanized drawbar by 300 mm with a 40 mm flange coupling ----General components: * Jost mechanical landing gear at the front * 2 mechanical, hot-dip galvanized folding supports at the rear * Hot-dip galvanized bolted underrun protection * Toolbox made of galvanized sheet steel on the right side * Plastic quarter fenders * 2-step step on the left side as an aid for getting on ----Electrical system / Lighting: * TPMS tire pressure monitoring system * 15-pole power connector * LED tail lights ----Tipping bridge: * Steel, 3-sided tipping body * Continuous side walls at the top with internal tube reinforcement - without center posts - foldable with side wall spring supports * Foldable and pivoting tailgate via manual central locking * Hot-dip galvanized bolted rear posts * 4 mm fine-grained steel floor * Lashing hooks, receiving rail at the rear for loading ramps * Preparation for later retrofitting of side wall extensions ----Chassis: * Hot-dip galvanized chassis ----Load securing: * 1 x 5 tons lashing point in each corner and 4 x 3 tons lashing eyes on each side, embedded in the outer frame ----ALU loading ramps: * 1 pair of ALU loading ramps approx. 3,570 x 400 mm (load capacity 8 tons / pair), suitable for rubber-tired and tracked vehicles * Lockable storage compartment at the rear below the loading area, embedded in the chassis ----Tires: Gujdpfx Asl Th A Ejm Tei * Tires 385/55 R 22.5 ----Painting: * The axles, springs, air tanks and landing gear are painted in a black tone. * Chassis, drawbar, floor, front panel, folding supports are hot-dip galvanized. * Painting of the side walls in RAL 9010 pure white. * Painting of the side walls in an RAL color against surcharge possible. ----Information: * Body reinforced with load securing certificate according to EN 12642 XL * New vehicle without initial registration with manufacturer's warranty * Errors and prior sale reserved ----Delivery time: * Available from approx. week 45/2026

Condition: new, maximum load weight: 10,760 kg, overall weight: 14,400 kg, axle configuration: 2 axles, loading space length: 6,270 mm, loading space width: 2,470 mm, loading space height: 400 mm, Year of construction: 2026, * ETÜ-TA-R 14.4: ----Brakes: * Drum brakes * Electronic Braking System (EBS) * Emergency release device for spring brake cylinders ----Axles: * 2 x 7 ton Gigant axles ----Suspension: * Parabolic springs with equalizing unit ----Drawbar / Flange coupling: * Drawbar adjustable in height by 300 mm * Drawbar extension by 250 mm to 2,250 mm * 40 mm flange coupling ----Lighting / Electrical: * TPMS (Tire Pressure Monitoring System) * LED lighting ----General components: * Jost support leg at the front * External hot-dip galvanized folding supports at the rear * Plastic toolbox on the front right side, on the front wall * Lateral underrun protection * Plastic quarter fenders ----Low-loader platform: * 50 mm softwood floor * Device in front of the front wall for subsequent installation of container locking mechanisms * Bolted front wall made of smooth sheet metal * Steel sheet metal side walls - trapezoidal - foldable with sideboard spring lifter * Steel rear wall can be slid between the ramps - bracket when not in use inside the front wall * Rear crossbars bolted ----Load securing: * Perforated outer frame, angled at approx. 45 degrees, with a lashing capacity of 2 tons every 480 mm * Installation of 3-ton lashing eyes possible every 600 mm * 1 x 6.3-ton lashing point in each corner at the front and rear * Various holes in the front and end crossmembers for 1.2-ton lashing * Profifix lashing rail in the longitudinal axis in the middle for lashing up to LC 3000 daN ----Ramps: * One-piece mechanical grating ramps with spring mechanism for single-person operation, approx. 2,750 x 600 mm (can be pushed together to 20 mm) Gedpfxoq Dyvvs Am Teui * Approach angle at the rear approx. 860 mm ----Painting: * Hot-dip galvanized chassis, drawbar, front wall, ramps and rear wall * Sideboard color in RAL 9010 pure white * Painting of the side walls in a RAL color possible at an extra charge ----Information: * --Reinforced and certified body according to EN 12642 XL incl. load securing certificate-- * New vehicle with manufacturer's warranty * Errors and prior sale excepted ----Delivery time: * Available from approx. week 47/2026

Condition: new, maximum load weight: 10,880 kg, overall weight: 14,400 kg, axle configuration: 2 axles, loading space length: 6,270 mm, loading space width: 2,470 mm, loading space height: 400 mm, Equipment: ABS, * Müller Mitteltal ETÜ-TA-R 14.4 Lowboy Trailer, traversable, with shortened side walls * Also ideal for use as a platform – as the stanchions can be quickly removed and the side walls can be locked in place * New vehicle, not yet registered * RAL 7035 light gray * GVWR: 14.4t, payload: 10.88t * GIGANT axles, EBS, twin tires 235/75R 17.5, parabolic springs * Unladen platform height 930mm / laden platform height 870mm * Chassis, front wall, ramps, drawbar: hot-dip galvanized * Wooden floor in a clamped design * Loading area 6.24m x 2.47m * Wooden floor in a clamped design, galvanized grating 0.62m in the 0.86m ramp section, replacing the wooden floor over the full width * 4 UVV lashing points (LC 6300daN) * Perforated outer frame, 45° bent, with hole pattern for lashing equipment, lashing force per lashing point LC 2000 daN with a minimum distance of 480 mm. * 10 UVV lashing points LC 3000 daN, recessed into the existing hole pattern in the outer frame * Ramps, one-piece, with hot-dip galvanized grating in a non-slip design, can be slid together to about 20 mm * Side walls in a special design, shortened to just before the rear slope with folding and removable rear stanchions * Locking of the folded-down side walls - making it easy to use as a platform * Ramp securing via retaining rod and inclined support * Ramp lifter with vertically arranged, adjustable springs for easy one-person operation * Rear wall, 300m aluminum, plug-in * 1 toolbox in front of the front wall * Excavator bucket rest made of hardwood, screwed to the front wall * 2 additional LED reversing lights * 1 rotating LED warning light, removable, at the rear * Height-adjustable support winch at the front, folding supports at the rear * Drawbar with 40mm drawbar eye, height-adjustable, 50mm eye also possible on request * In front of the front wall, provision for subsequent installation of 2 container locking mechanisms * ----Leasing, hire purchase, financing, trade-in possible * e.g. 585 € net for a term of 60 months * We have been Müller Mitteltal's sales partner for over 10 years * Our opening hours * Monday - Thursday: 08:00 - 17:00 Guedpfxs Af Dlco Am Tei * Friday: 08:00 - 15:00 Outside of opening hours, we are available by appointment. We speak German, we speak English, mowimy po polsku, on parle français

Condition: new, maximum load weight: 13,650 kg, overall weight: 18,000 kg, axle configuration: 2 axles, Year of construction: 2026, * RAK 18.0 external roller with rear tilting function ----Brakes: * Wabco EBS-E (electronic braking system) * Emergency release system for spring brake cylinders * Drum brakes ----Axle: * BPW Eco Plus axles ----Suspension: * Air suspension (automatic lowering when the brake is released) ----Drawbar: * Pneumatically lowerable drawbar, approx. 2,100 mm long, with 40 mm drawbar eye and height adjustment via tension spring & locking bolt ----General components: * Plastic toolbox - approx. 858 x 500 x 500 mm - on the right side * Closed plastic fenders, front and rear * Closed side underrun protection * Rear underrun protection, bolted on * Storage box for container nets, made of galvanized perforated sheet metal, approx. 1,000 x 500 x 500 mm * Folding A-sign at the rear * Rear impact protection buffer ----Electrical system / Lighting: * EBS multi-voltage system for towing vehicles with 12 & 24V electrical systems * 15-pole 24V power connector * LED lighting system for 12 & 24V * 2 additional LED reversing lights * TPMS (tire pressure monitoring system) ----Suitable for container lengths: * For containers from 6,500 mm to 7,000 mm ----Container running surface / Tilting platform: * Roller guidance on the outside through flat steel border with a clear distance of approx. 2,180 mm, in combination with 3 centering pieces on each side for container guidance * At the rear, 2 recessed roller bearings connected to the tilting frame are mounted for receiving and stopping the container rollers, with pneumatic activation to prevent longitudinal slippage * The positive locking of the roller containers is achieved via a pneumatic transverse locking unit installed at the front of the tilting frame and operated from the outside (single-sided operation) * Chassis frame inside with rear-tilting main frame - motor-hydraulic tilting system in single-cylinder design * Tilting angle 42° * Rubber pads between chassis and tilting frame * The containers are pushed on from the front; chassis is hot-dip galvanized ----Tires: * Single tires 385/55 R 22.5 ----Loading height: * Unladen, approx. 1,270 mm ----Painting: * Underrun protection and locking parts (without topcoat) * Bogie, air tank, axles, slewing ring and drawbar painted in a black tone * Hot-dip galvanized ----Information: * For container transport according to DIN 30722 Part 1 * New vehicle without initial registration with manufacturer's warranty * Errors and prior sale subject to change Gsdpfx Aox Ipbmom Teui ----Delivery time: * Available from approximately week 15/2027

Condition: new, maximum load weight: 10,660 kg, overall weight: 14,400 kg, axle configuration: 2 axles, loading space length: 5,000 mm, loading space width: 2,420 mm, loading space height: 600 mm, Year of construction: 2026, * KA-TA-R 14.4: ----Brakes: * Wabco EBS (electronic braking system) * Emergency release device for spring brake cylinders * Drum brakes Gusdpfx Amex Hm Ris Tei ----Axles: * 2 x 7-ton Gigant axles ----Suspension: * Parabolic springs with tandem equalizer ----Drawbar / Flange coupling: * Height-adjustable drawbar by 300 mm with 40 mm flange coupling ----Electrical system / Lighting: * 15-pin power connector * LED rear lights 12/24 V * Tire pressure monitoring with display option in the truck via EBS signal - without truck-side installation ----General components: * Jost mechanical front support legs * 2 mechanical folding support legs at the rear * Plastic toolbox approx. 750 x 350 x 300 mm at the front, on the right side of the chassis * Underrun protection, bolted * Plastic quarter fenders ----Tipping platform: * Net hooks on each of the bearings of the central locking mechanism, as well as 2 on the front wall * Steel pallet-sided 3-way tipping body with adjustable Strong side panels (continuous side walls with internal tube reinforcement at the top - without center rails - can be folded down with side panel spring-assisted lifters) * Rear frame rails bolted * Combination steel wing doors - rear wall, 2-wing, asymmetrical split - can be pivoted and locked at 270° - not foldable - as well as with additional pivoting frames for the automatic rear wall opening during tipping, locking via galvanized swivel rod latch at the rear and central locking, deactivation function for automatic rear wall function when tipping backwards with the wing door open * 4 mm sheet metal floor made of fine-grained steel ----Load securing: * 1 x 5-ton lashing eye in each corner * 4 x 3-ton lashing eyes on each side, recessed in the outer frame ----Chassis: * Chassis made of fine-grained steel ----Ramps: * Rear receiving rail for the loading ramps * 1 pair of aluminum loading ramps approx. 3,570 x 410 mm (load capacity 10 tons / pair) suitable for rubber-tired and tracked vehicles * Storage compartment below the loading area in the chassis for the ramps, lockable from the rear ----Tires: * Tires 358/55 R 19.5 ----Painting: * Drawbar, underrun protection, rear frame, folding support legs at the rear hot-dip galvanized * Axles, springs, air tanks and support legs painted in a black tone * Painting of the side panels in a RAL color of your choice (but no special or metallic paint) - can be changed up to approx. 6 weeks before completion ----Information: * Superstructure - reinforced - with load securing certificate * Errors and prior sale subject to change * Sample images ----Delivery time: * Available for immediate delivery from week 47/2026

Condition: new, maximum load weight: 10,660 kg, overall weight: 14,400 kg, axle configuration: 2 axles, loading space length: 5,000 mm, loading space width: 2,420 mm, loading space height: 600 mm, Year of construction: 2026, * KA-TA-R 14.4: ----Brakes: * Wabco EBS (electronic braking system) * Emergency release device for spring brake cylinders * Drum brakes ----Axles: * 2 x 7-ton Gigant axles ----Suspension: * Parabolic springs with tandem equalizer ----Drawbar / Flange coupling: * Height-adjustable drawbar by 300 mm with 40 mm flange coupling ----Electrical system / Lighting: * 15-pin power connector * LED rear lights 12/24 V * Tire pressure monitoring with display option in the truck via EBS signal - without truck-side installation ----General components: * Jost mechanical front support legs * 2 mechanical folding support legs at the rear * Plastic toolbox approx. 750 x 350 x 300 mm at the front, on the right side of the chassis * Underrun protection, bolted * Plastic quarter fenders ----Tipping platform: * Net hooks on each of the bearings of the central locking mechanism, as well as 2 on the front wall Godpex Hm Rcjfx Am Teui * Steel pallet-sided 3-way tipping body with adjustable Strong side panels (continuous side walls with internal tube reinforcement at the top - without center rails - can be folded down with side panel spring-assisted lifters) * Rear frame rails bolted * Combination steel wing doors - rear wall, 2-wing, asymmetrical split - can be pivoted and locked at 270° - not foldable - as well as with additional pivoting frames for the automatic rear wall opening during tipping, locking via galvanized swivel rod latch at the rear and central locking, deactivation function for automatic rear wall function when tipping backwards with the wing door open * 4 mm sheet metal floor made of fine-grained steel ----Load securing: * 1 x 5-ton lashing eye in each corner * 4 x 3-ton lashing eyes on each side, recessed in the outer frame ----Chassis: * Chassis made of fine-grained steel ----Ramps: * Rear receiving rail for the loading ramps * 1 pair of aluminum loading ramps approx. 3,570 x 410 mm (load capacity 10 tons / pair) suitable for rubber-tired and tracked vehicles * Storage compartment below the loading area in the chassis for the ramps, lockable from the rear ----Tires: * Tires 358/55 R 19.5 ----Painting: * Drawbar, underrun protection, rear frame, folding support legs at the rear hot-dip galvanized * Axles, springs, air tanks and support legs painted in a black tone * Painting of the side panels in a RAL color of your choice (but no special or metallic paint) - can be changed up to approx. 6 weeks before completion ----Information: * Superstructure - reinforced - with load securing certificate * Errors and prior sale subject to change * Sample images ----Delivery time: * Available for immediate delivery from week 47/2026

Condition: excellent (used), first registration: 06/2018, color: other, Superstructure Year of manufacture: 2018 = More information = Year of construction: 2018 Empty weight: 6.630 kg Carrying capacity: 23.370 kg GVW: 30.000 kg Technical condition: very good Visual appearance: very good Registration number: QAKP268 = Dealer information = Do you have any questions or suggestions? Please feel free to contact us. We guarantee a response within 8 hours. Prices do not include VAT. No rights may be derived from the information provided. Office phone number: Mobile: Dutch - English - German - French - Spanish - Italian) Available via WhatsApp and Viber. Mobile: Available via WhatsApp and Viber. Gedpfx Amoz Ezmks Toui When paying by bank transfer, the funds must be transferred to our bank account listed below. Always verify the payment details on our website. Please contact us if you have received different information. If in doubt, please call us so we can verify the invoice and/or payment. Bank details: Bank name: ING Bank address: Bijlmerdreef 106 1102 CT Amsterdam IBAN number: NL97INGB0117176699 EORI/VAT/TAX: NL810574901B(01) BIC/SWIFT: INGBNL2A

Condition: new, maximum load weight: 30,740 kg, overall weight: 40,000 kg, axle configuration: > 3 axles, Year of construction: 2026, * T 4: * Wabco EBS-E (electronic braking system) * RDÜ tire pressure monitoring system * Emergency release device for spring brake cylinders * Drum brakes * 4 x 11 t Gigant axles * Air suspension with lifting/lowering function and RtR valve * Smard on-board system for load weight determination * Warning sign packages front & rear Guedol Tphrspfx Am Tei * Reflective contour tape on sides and rear * Removable rotating beacon at rear * LED lighting * Straight drawbar with 50 mm towing eye and stepless height adjustment * Tool box made of powder-coated steel and spare wheel holder, basket design, right side * Front: closed single fender made of plastic * Rear: straight steel mudguards with spray protection (anti-spray device) * Side underrun protection * Turntable platform front section extended by 520 mm with 45° corners and 3 integrated storage compartments incl. lids, lockable * Chassis made of high-strength fine-grained steel * Floor above turntable platform: 50 mm, in low-loader platform: 60 mm softwood * Outer planks of the ramp made from hardwood * 4 stake pockets on each side (no stakes included), each offering 2 t lashing option * Load securing kit consisting of: 2 lashing rings 6.4 t at the front left and right on the main frame of the turntable platform * Each front and rear side: 2 pairs of 13.4 t lashing rings on the outer frame, as well as 4 pairs per side of 10 t folding and lowerable lashing rings * Loadable from any direction and recessed into the outer frame * 2 pairs of 6.4 t lashing rings on the side in the excavator arm storage * 8 pairs of galvanized folding outriggers for 3 m overall width (not at the rear slope) * Widening planks stowed on the left in a storage compartment * Excavator arm storage above the rear axle up to end of access slope approx. 2,100 x 740 x 190 mm * Mechanical rear drop supports * Hydraulic folding ramps with hydraulically adjustable tapered section, approx. 4,650 x 720 mm, incl. hydraulic side ramp displacement & load-holding valve * Loading area above turntable: approx. 2,990 x 2,520 mm * Rear loading area: approx. 6,780 x 2,520 mm * Loaded platform height: approx. 890 mm, +/- 20 mm (including 860 mm access slope) * Flow divider installed * Chassis, turntable, ramps, folding outriggers, and mechanical drop supports hot-dip galvanized * Axles, drawbar, air tanks, and turntable painted in black * Tires: 235/75 R 17.5 * New vehicle without initial registration, with manufacturer's warranty * Errors and prior sale excepted * Immediately available from Egestorf on the A7

Condition: used, axle configuration: 3 axles, first registration: 11/2005, Side-mounted, sliding access ramps (L x W) 3050 x 650 mm, with spring-assisted lifting mechanism. PA1776 Gusdpfx Amez I Hppj Tei Our offer generally does not include a new TÜV (German technical inspection) certificate. If a new TÜV certificate is desired, we will gladly provide you with a quote from our partner workshops! The vehicle may be covered with advertising and/or lettering. Our general terms and conditions of delivery and payment apply. We would be happy to prepare a financing or leasing offer for this vehicle. Please contact us!

Condition: new, maximum load weight: 30,740 kg, overall weight: 40,000 kg, axle configuration: > 3 axles, Year of construction: 2026, * T 4: * Wabco EBS-E (electronic braking system) Godpfxsl Tik Ns Am Teui * RDÜ tire pressure monitoring system * Emergency release device for spring brake cylinders * Drum brakes * 4 x 11 t Gigant axles * Air suspension with lifting and lowering device and RtR valve * SmarD on-board system for load weight determination * Warning sign packages front & rear * Reflective contour tape on sides and rear * Removable rotating beacon at the rear * LED lights * Straight drawbar with 50 mm towing eye and infinitely adjustable height * Tool box made of powder-coated steel and spare wheel holder in basket design, mounted on the right side * Enclosed plastic single fenders at the front * Straight steel mudguards at the rear, each with spray suppression (anti-spray system) * Side underrun protection * Turntable platform extended by 520 mm with 45° corners and 3 integrated storage compartments incl. cover, lockable * Chassis made of high-strength fine-grained steel * Floor over turntable platform made of 50 mm softwood, in the low-bed platform made of 60 mm softwood * Outer planks of the loading ramps made of hardwood * 4 stake pockets on each side (no stakes included) with simultaneous 2 t lashing point per pocket * Load securing package consisting of: 2 lashing points 6.4 t at the front left and right on the main frame of the turntable platform * 2 pairs of 13.4 t lashing rings each at the outer frame front and rear, as well as 4 pairs of 10 t lashing rings per side, swiveling and retractable * Loadable in all directions and recessed into the outer frame * 2 pairs of 6.4 t lashing rings in the excavator arm rest area * 8 pairs of galvanized swing-out marker boards for 3 m total width (not at the rear slope) * Widening planks stored in a compartment on the left side * Excavator arm rest above rear axle up to end of approach ramp approx. 2,100 x 740 x 190 mm * Mechanical drop-down supports at the rear * Hydraulic folding ramps with hydraulically adjustable tip, approx. 4,650 x 720 mm incl. hydraulic lateral ramp shifting and load-holding valve * Loading area across the turntable: approx. 2,990 x 2,520 mm * Rear loading area: approx. 6,780 x 2,520 mm * Loading height loaded: approx. 890 mm, +/- 20 mm (incl. 860 mm approach slope) * Flow divider installed * Chassis, turntable, access ramps, flip-out marker boards and mechanical drop-down supports hot-dip galvanized * Axles, drawbar, air tanks, and turntable painted in black * Tires: 235/75 R 17.5 * New vehicle without first registration, with manufacturer warranty * Subject to errors and prior sale * Immediately available ex Egestorf on the A7

Condition: used, empty load weight: 6,500 kg, maximum load weight: 23,500 kg, overall weight: 30,000 kg, axle configuration: 3 axles, first registration: 06/2010, suspension: steel, tire size: 235 / 75 R 17,5, color: other, gearing type: other, front tire size: 235 / 75 R 17,5, rear tire size: 235 / 75 R 17,5, driver cabin: other, emission class: none, fuel: biodiesel, Equipment: ABS, compressed air brake, Vehicle is sold on behalf of a customer, partly wooden boards def., 17 pairs of lashing eyes, , loading height approx. 900 mm, , -- Misprints, errors and omissions excepted, sample pictures --, More data under: !, More Details: ! Gsdj Ai Du Dopfx Am Tjui

Condition: new, maximum load weight: 8,750 kg, overall weight: 11,900 kg, axle configuration: 2 axles, loading space length: 5,000 mm, loading space width: 2,420 mm, loading space height: 500 mm, Year of construction: 2026, Equipment: ABS, tail-lift, Müller?Mitteltal KA-TA-R 11.9 Tandem low-loader, three-sided tipping trailer with ramps Inquiry number: 11731, available immediately * NEW vehicle, not yet registered * Available in RAL 9016 traffic white * Delivery possible for an extra charge! * GVWR: 11,900 kg, payload 8,750 kg. * Floor galvanized * 5m x 2.42m x 0.5m side walls, hinged, foldable, and removable, prepared for later retrofitting of side wall extensions * Front wall hot-dip galvanized * Lockable compartment under the tipping bridge for the loading ramp * Incl. loading ramps 3.31m, 8t pair * Tool box made of plastic, mounted on the chassis frame on the right side in the direction of travel * 4 UVV lashing eyes LC 5000daN, recessed and foldable, at the front and rear * 8 lashing eyes LC 3000daN, recessed and foldable, in the tipper bed * Net hooks Guodpfs Af Dk Ejx Am Tei * Drawbar continuously adjustable in height, hot-dip galvanized, drawbar eye 40mm * Frame galvanized * Tires 235/75R 17.5, (4), BPW axles, parabolic springs * Tire pressure monitoring system * EBS * LED lighting system for 12+24 volts * Side marker lights with turn signal control * Bolted, galvanized rear supports * Excavator bucket rest mounted on the front wall * Two-step access in front of the front wall (galvanized) * ---- * Please request a quote from us; additional equipment possible * Financing available from 495 € net per month for 60 months without down payment and without residual value. An offer from our financing partner "FM LeasingPartner". * ---- Our opening hours Monday - Thursday: 08:00 - 17:00 Friday 08:00 - 15:00 Outside of opening hours, we are available by appointment. Whatsapp Leasing, financing, trade-in possible.

Condition: used, Vacuum tank, approx. 6 m³, suitable for Müller-Mitteltal CHK. Includes PTO-driven vacuum pump and various hoses. Vacuum pump Guodpfx Asx Nl Npjm Tsi = Further information = Year of manufacture: 2010 Please contact Jan-Marc Schwickert for more information.

Condition: new, maximum load weight: 8,670 kg, overall weight: 11,900 kg, axle configuration: 2 axles, loading space length: 5,000 mm, loading space width: 2,420 mm, loading space height: 500 mm, Year of construction: 2026, * KA-TA-R 11.9 Masterline: ----Brakes: * Wabco EBS * Emergency release system for spring brake cylinders * Drum brakes ----Axle: * 2 x 5.5 ton BPW axles ----Suspension: * Parabolic springs with tandem equalizing unit ----Drawbar / Flange coupling: * Height-adjustable, hot-dip galvanized drawbar by 300 mm with 40 mm flange coupling ----Electrical system / Lighting: * TPMS tire pressure monitoring system * LED lighting * 15-pole electrical connector ----General components: * Toolbox made of galvanized sheet steel on the right side * Bolted underrun protection * Plastic quarter fenders * Jost mechanical support winch at the front * 2 mechanical, hot-dip galvanized folding supports at the rear ----Tipping bridge: * Net hooks on the side and rear in the bearings of the central locking system, as well as 3 on the outside of the front wall * Hot-dip galvanized chassis * Steel 3-sided tipping body * Continuous side walls without a center rail, foldable with sideboard spring lifters * Foldable and pivoting tailgate via manual central locking * Hot-dip galvanized bolted rear rail * 4 mm steel sheet floor * Mounting rail at the rear for loading ramps ----Load securing: * 1 x 5 ton recessed and foldable lashing points in each corner * As well as 4 x 3 ton lashing points on each side, embedded in the outer frame and foldable ----Ramps: * 1 pair of aluminum loading ramps approx. 3,310 x 400 mm (load capacity 8 tons / pair) suitable for vehicles with rubber tires and track vehicles * Lockable storage compartment at the rear under the loading area, embedded in the chassis ----Tires: * Tires 235/75 R 17.5 ----Paintwork: * Axles, springs, air tanks, drawbar and support winch painted in a black tone * Sideboard painted in RAL 9010 pure white * Painting of the side walls in a RAL color against extra charge * Floor and front wall hot-dip galvanized ----Information: * Body reinforced with load securing certificate according to EN 12642 XL Gusdpfx Aoq Hg Dxem Tei * New vehicle with manufacturer's warranty * Errors and prior sale reserved ----Delivery time: * Available from approx. week 45/2026

Condition: new, maximum load weight: 30,080 kg, overall weight: 40,000 kg, axle configuration: > 3 axles, Year of construction: 2026, * T4 RM 40.0: * Wabco EBS-E (electronic braking system) * Emergency release device for spring-loaded cylinders * Tire pressure monitoring with display option in the truck via EBS signal – no truck-side installation required * Drum brakes * 4 x 11 t Gigant axles * Air suspension with manual lowering at the rear * Warning sign packages front and rear * SmartBord infotool installed with pressure sensors for displaying total axle load per axle group * Reflective contour tape on the sides and rear * Removable LED rotating beacon at the rear * 15-pin power connector * LED tail lights * Straight drawbar with 50 mm towing eye and stepless height adjustment * Front closed single plastic mudguards * Rear straight steel mud flaps each with splash guards (spray suppression) * Side underrun protection * Front extension in front of the bogie platform approx. 520 mm with 45° corners and 3 storage compartments including lockable hinged covers (covers open to the rear) * Chassis made of high strength fine-grain steel * Floor over bogie platform made of 50 mm softwood and 60 mm on the lowbed platform * Outer planks of the loading ramps made of 50 mm hardwood * Lashing package consisting of: 2 lashing eyes 6.4 t front left and right on the main frame of the bogie platform, side front and rear each 1 pair of 13.4 t lashing rings on the outer frame, and side each 1 pair of 10 t lashing rings, swiveling and lowerable, loadable in all directions and recessed into the outer frame, bolted 5 t lashing rings to the outer frames of the wheel wells (2 at the front wheel well and 1 at the rear), 2 pairs of 6.4 t lashing rings at the side in the excavator arm rest * 11 pairs of folding outriggers for 3 m total width (except on rear slope) * Storage compartment (L = 2,470 x W = 570 x H = 250 mm) for the widening planks made of steel sheet, mounted transversely to the loading platform in front of the 1st rear axle * Excavator arm rest above the rear axle to the end of the drive-up slope, approx. 2,300 x 740 x 190 mm * Each side with 2 wheel wells approx. 640 mm wide – front 340 mm deep, rear 220 mm deep – with sliding covers (storage for the covers on the front of the bogie platform) for the transport of wheel loaders with a wheelbase of 3,100 – 3,640 mm * Mechanical drop-down supports at the rear * Hydraulic folding ramps with hydraulically extendable tip, approx. 4,650 x 720 mm * Hydraulic lateral ramp shift * Loading area above the slewing ring: approx. 2,990 x 2,520 mm * Rear loading area: approx. 6,780 x 2,520 mm, loaded height approx. 890 mm +/- 20 mm (incl. 860 mm drive-up slope) * Chassis, bogie, folding outriggers, rear drop supports and loading ramps hot-dip galvanized Guodpfx Amjxmpyko Tei * Axles, air tanks and drawbar painted black * Tires: 235/75R17.5 * Vehicle is hot-dip galvanized * New vehicle with manufacturer’s warranty * Subject to errors and interim sale * Immediately available ex Egestorf

Condition: new, maximum load weight: 30,080 kg, overall weight: 40,000 kg, axle configuration: > 3 axles, Year of construction: 2026, * T4 RM 40.0: * Wabco EBS-E (electronic braking system) * Emergency release device for spring brake cylinders * Tire pressure monitoring with display capability in the truck via EBS signal (no truck-side installation required) * Drum brakes * 4 x 11 ton Gigant axles * Air suspension with manual lowering at the rear * Warning sign packages front & rear * SmartBord infotool mounted with pressure sensors for total axle load display per axle group * Side and rear reflective contour tape * Removable LED beacon at the rear * 15-pin power connector * LED tail lights * Straight drawbar with 50 mm towing eye and stepless height adjustment * Closed single plastic mudguards at the front * Straight rear steel mud flaps each with spray suppression * Side underrun protection * Front extension in front of turntable platform approx. 520 mm with 45° corners and 3 storage compartments incl. lockable folding lids (open to the rear) * Chassis made of high-strength fine-grain steel * Floor above turntable platform made of 50 mm softwood and 60 mm softwood on low-bed platform * Outer planks of the ramps made of 50 mm hardwood * Load securing package consisting of: 2 lashing eyes 6.4 t front left and right on the main frame of the turntable platform; one pair each (front & rear) of 13.4 t lashing rings on the outer frame; one pair each side of 10 t swivel and lowerable lashing rings, loadable in all directions and integrated in the outer frame; bolted 5 t lashing rings on the outer frames of the wheel wells (2 at the front wheel well, 1 at the rear); 2 pairs of 6.4 t lashing rings at the sides of the excavator boom cradle * 11 pairs of folding outriggers for a total width of 3 meters (not on rear slope) * Storage compartment (L = 2,470 x W = 570 x H = 250 mm) for widening planks made of sheet steel, mounted transverse to the load area in front of the 1st rear axle * Excavator boom cradle above the rear axle to end of incline approx. 2,300 x 740 x 190 mm * 2 wheel wells per side, approx. 640 mm wide – front 340 mm deep, rear 220 mm deep – with sliding cover (storage for covers at the front on the turntable platform) for transporting wheel loaders with 3,100 - 3,640 mm wheelbase * Mechanical drop-down supports at the rear * Hydraulic folding ramps with hydraulically deployable tip section approx. 4,650 x 720 mm * Hydraulic lateral ramp shift Guedpfx Amoxmpydo Tei * Loading area above fifth wheel: approx. 2,990 x 2,520 mm * Rear loading area: approx. 6,780 x 2,520 mm, loaded height approx. 890 mm +/- 20 mm (incl. 860 mm approach slope) * Chassis, turntable, folding outriggers, rear supports, and ramps hot-dip galvanized * Axles, air tanks, and drawbar painted black * Tires: 235/75R17.5 * Vehicle is hot-dip galvanized * New vehicle with manufacturer warranty * Subject to change and prior sale * Immediately available ex Egestorf

Condition: new, maximum load weight: 10,400 kg, overall weight: 14,400 kg, axle configuration: 2 axles, loading space length: 5,500 mm, loading space width: 2,420 mm, loading space height: 500 mm, Year of construction: 2026, * ETK-TA-R 14.4: ----Brakes: * EBS * Emergency release system for spring brake cylinders Gjdstr St Uepfx Am Toui * Drum brakes ----Axle: * 2 x 7-ton Gigant axles ----Suspension: * Parabolic springs with tandem equalizing unit ----Drawbar / Flange coupling: * Drawbar adjustable in height by 300 mm with 40 mm flange coupling ----Electrical system / Lighting: * Tire pressure monitoring system with display option in the truck via EBS signal, without installation on the truck side * 15-pole power connector * LED tail lights ----General components: * Mechanical support winch at the front * 2 mechanical folding supports at the rear * Plastic toolbox approx. 750 x 350 x 300 mm on the right side * Bolted underbody protection * Plastic quarter fenders ----Frame: * Main frame made of fine-grain steel ----Tipping body: * Net hooks on the side and at the rear in the bearings of the central locking system, as well as 2 pieces on the front wall * Steel pallet-sided, 2-way tipping body, front wall fixed, made of smooth sheet metal, continuous side walls - without center rails, foldable with side board spring lifters, and pivoting via manual central locking * Rear rails bolted * Steel rear wall inserted in front of the ramps * 1 x 5-ton lashing eye in each corner, as well as 4 x 3-ton lashing eyes on each side, embedded in the outer frame * 4 mm floor made of fine-grain steel ----Ramps: * Two-part mechanical grating ramps with aluminum tip, 2,150 + 1,300 mm x 600 mm (manually adjustable to 80 mm) ----Painting: * Chassis, drawbar, rear rails, underbody protection, mechanical fall supports and ramps hot-dip galvanized * Axles, springs, air tanks, flange coupling and support winch painted in a black shade * Side boards and tipping body in RAL 9010 pure white * Painting of the side walls and tipping body in a RAL color is possible for an extra charge ----Information: * New vehicle with manufacturer's warranty * Errors and prior sale excepted ----Delivery time: * Available for immediate delivery from Egestorf

Condition: new, maximum load weight: 10,400 kg, overall weight: 14,400 kg, axle configuration: 2 axles, loading space length: 5,500 mm, loading space width: 2,420 mm, loading space height: 500 mm, Year of construction: 2026, * ETK-TA-R 14.4: ----Brakes: * EBS * Emergency release system for spring brake cylinders * Drum brakes ----Axles: * 2 x 7-ton Gigant axles ----Suspension: * Parabolic springs with tandem equalizer ----Drawbar / Flange coupling: * Height-adjustable drawbar by 300 mm with 40 mm flange coupling ----Electrical system / Lighting: * Tire pressure monitoring system with display option in the truck via EBS signal without truck-side installation * 15-pole power socket * LED tail lights ----General components: * Mechanical support jacks at the front * 2 mechanical folding supports at the rear * Plastic toolbox approx. 750 x 350 x 300 mm on the right side * Bolted underrun protection * Plastic quarter fenders Guedpfx Aotr Sucsm Tei ----Frame: * Main frame made of fine-grain steel ----Tipping platform: * Net hooks on the side and rear in the bearings of the central locking system, as well as 2 pieces on the front wall * Steel pallet-sided 2-way tipping body, front wall fixed, made of smooth sheet metal, continuous side walls - without center rails, foldable with side board spring lift and pivoting via manual central locking * Rear rails bolted on * Steel rear wall inserted in front of the ramps * 1 x 5-ton lashing point in each corner, as well as 4 x 3-ton lashing eyes on each side embedded in the outer frame * 4 mm floor made of fine-grain steel ----Ramps: * Two-part mechanical grid ramps with aluminum tip, 2,150 + 1,300 mm x 600 mm (manually adjustable up to 80 mm) ----Painting: * Chassis, drawbar, rear rails, underrun protection, mechanical support jacks, and ramps hot-dip galvanized * Axles, springs, air tanks, flange coupling, and support jacks painted in a black tone * Side boards and platform painted in RAL 9010 pure white * Painting of the side walls and tipping platform in a RAL color is possible for an extra charge ----Information: * New vehicle with manufacturer's warranty * Errors and prior sale excepted ----Delivery time: * Available immediately from Egestorf

Condition: new, suspension: other, color: other, gearing type: other, driver cabin: other, emission class: none, fuel: biodiesel, Storage compartment for aluminum ramps, price per storage compartment, length approx. 2.48 m, width approx. 1 m, height approx. 27 cm, , --  Misprints, errors and changes reserved, sample images --, More information at: !, More details: ! Gujdpfx Amo Aihgro Tji

Condition: new, maximum load weight: 10,760 kg, overall weight: 14,400 kg, axle configuration: 2 axles, loading space length: 6,270 mm, loading space width: 2,470 mm, loading space height: 400 mm, Year of construction: 2026, * ETÜ-TA-R 14.4: ----Brakes: * Drum brakes * Electronic Braking System (EBS) * Emergency release device for spring brake cylinders ----Axles: * 2 x 7 ton Gigant axles ----Suspension: * Parabolic springs with equalizing unit ----Drawbar / Flange coupling: * Drawbar adjustable in height by 300 mm * Drawbar extension by 250 mm to 2,250 mm * 40 mm flange coupling ----Lighting / Electrical: * TPMS (Tire Pressure Monitoring System) * LED lighting ----General components: * Jost support leg at the front * External hot-dip galvanized folding supports at the rear * Plastic toolbox on the front right side, on the front wall * Lateral underrun protection * Plastic quarter fenders ----Low-loader platform: * 50 mm softwood floor * Device in front of the front wall for subsequent installation of container locking mechanisms * Bolted front wall made of smooth sheet metal * Steel sheet metal side walls - trapezoidal - foldable with sideboard spring lifter * Steel rear wall can be slid between the ramps - bracket when not in use inside the front wall * Rear crossbars bolted ----Load securing: * Perforated outer frame, angled at approx. 45 degrees, with a lashing capacity of 2 tons every 480 mm * Installation of 3-ton lashing eyes possible every 600 mm * 1 x 6.3-ton lashing point in each corner at the front and rear * Various holes in the front and end crossmembers for 1.2-ton lashing * Profifix lashing rail in the longitudinal axis in the middle for lashing up to LC 3000 daN Gujdpfxervvflj Am Toi ----Ramps: * One-piece mechanical grating ramps with spring mechanism for single-person operation, approx. 2,750 x 600 mm (can be pushed together to 20 mm) * Approach angle at the rear approx. 860 mm ----Painting: * Hot-dip galvanized chassis, drawbar, front wall, ramps and rear wall * Sideboard color in RAL 9010 pure white * Painting of the side walls in a RAL color possible at an extra charge ----Information: * --Reinforced and certified body according to EN 12642 XL incl. load securing certificate-- * New vehicle with manufacturer's warranty * Errors and prior sale excepted ----Delivery time: * Available from approx. week 47/2026

Condition: used, machine/vehicle number: GE11/142/2022, empty load weight: 6,350 kg, maximum load weight: 17,650 kg, overall weight: 24,000 kg, axle configuration: 3 axles, first registration: 08/2008, loading space length: 8,500 mm, loading space width: 2,500 mm, suspension: air, Very well-maintained vehicle from first owner Three-axle low-loader trailer Guodpfjn Aw Hkox Am Tji Low-loader with drive-up ramp Heavy-duty transport Model T3 Komakt 30.0 Length 8,500 mm Width 2,500 mm Air suspension Commercial/export net price – €15,990 Subject to changes, interim sale, and errors ===== Phone2 Mobile =====