Used Müller-Mitteltal Roll-Off Trailers for sale (254)

Condition: new, maximum load weight: 10,800 kg, overall weight: 14,400 kg, axle configuration: 2 axles, loading space length: 6,270 mm, loading space width: 2,470 mm, Year of construction: 2025, * ETÜ-TA-R 14.4: ----Brakes: * EBS brake system * Emergency release device for spring brake cylinders * Drum brakes ----Axles: * 2 x 7 t Gigant axles ----Suspension: * Parabolic springs with compensation unit ----Drawbar / Flange Drawbar Eye: * Height-adjustable drawbar, adjustable by 300 mm * Drawbar extension by 250 mm to reach 2,250 mm ----Electrics / Lighting: * Tire pressure monitoring with display option in truck via EBS signal – no truck-side installation required * 15-pin power connector * LED lighting system 12 / 24 V * EBS multi-voltage system for towing vehicles with 12 and 24 V electrics ----General Attachments: * Landing gear at the front * External folding supports at the rear * Plastic toolbox approx. 858 x 500 x 500 mm, mounted front right on the bulkhead * Side underrun protection * Plastic quarter mudguards ----Low Loader Platform: * 50 mm softwood floor Njdpfx Ajrwc R Aocyscl * Preparation in front of the bulkhead for retrofitting container locks * Bolted 400 mm smooth sheet metal bulkhead * Bolted rear stakes * Side walls with spring-assisted lift ----Load Securing: * Perforated outer frame, approx. 45 degrees angled, with 2 t lashing capacity every 480 mm * Option to install 3 t recessed lashing rings every 600 mm * In each front and rear corner, 1 x 6.3 t lashing ring * Various holes in the front and end crossmembers for 1.2 t lashing options ----Ramps: * One-piece hydraulic grid ramps approx. 2,750 x 600 mm (can be retracted to 20 mm) * Hydraulic flow divider in the trailer (for truck-mounted hydraulic pump output over 40 l/min up to max. 140 l/min) ----Coating: * Chassis, drawbar, bulkhead, mechanical rear supports and ramps hot-dip galvanized * Axles, springs, air tanks, front landing gear, and flange drawbar eye painted in black * Side walls painted in RAL 9010 pure white * Painting of side panels in any RAL color available as an option for a surcharge ----Information: * New vehicle with manufacturer warranty * Subject to errors and prior sale ----Delivery time: * Immediately available from Egestorf

Condition: new, maximum load weight: 10,800 kg, overall weight: 14,400 kg, axle configuration: 2 axles, loading space length: 6,270 mm, loading space width: 2,470 mm, Year of construction: 2025, * ETÜ-TA-R 14.4: ----Brakes: * EBS brake system * Emergency release device for spring brake cylinders * Drum brakes ----Axles: * 2 x 7 t Gigant axles ----Suspension: Nsdpsxvgrpsfx Acyjcl * Parabolic springs with equalizer assembly ----Drawbar / Flange Drawbar Eye: * Drawbar adjustable in height by 300 mm * Drawbar extension by 250 mm, up to 2,250 mm ----Electrics / Lighting: * Tire pressure monitoring with the option of display in the truck via EBS signal—no truck-side installation required * 15-pin power connector * LED lighting system 12 / 24 V * EBS multi-voltage system for towing vehicles with 12 and 24 V electrics ----General Attachments: * Support winch at the front * Outward folding rear supports * Plastic toolbox approx. 858 x 500 x 500 mm mounted at the front right outside of the bulkhead * Lateral underrun protection * Plastic quarter mudguards ----Low Loader Deck: * 50 mm softwood floor * Preparation in front of the bulkhead for retrofitting container locks * Bolted 400 mm bulkhead made of smooth sheet metal * Rear stanchions bolted * Drop sides with spring assist ----Load Securing: * Perforated outer frame, angled at approx. 45 degrees, with 2 t lashing capacity every 480 mm * Installation of 3 t retractable lashing rings possible every 600 mm * 1 x 6.3 t lashing point in each corner at the front and rear * Various drilled holes in front and rear cross-members for 1.2 t lashing options ----Ramps: * One-piece hydraulic grate drive-up ramps approx. 2,750 x 600 mm (can be retracted to 20 mm) * Hydraulic flow divider in the trailer (for hydraulic pump capacity in the truck from over 40 l/min up to max. 140 l/min) ----Paintwork: * Chassis, drawbar, front wall, mechanical fall supports and drive-up ramps hot-dip galvanized * Axles, springs, air tanks, front support winch, and flange drawbar eye painted in black * Sideboards painted in RAL 2011 deep orange * Painting of side walls in an RAL colour available at extra cost ----Info: * New vehicle with manufacturer's warranty * Subject to errors and prior sale ----Delivery Time: * Available immediately ex Egestorf

Condition: used, maximum load weight: 12,080 kg, overall weight: 14,400 kg, axle configuration: 2 axles, first registration: 06/2024, loading space length: 3,900 mm, loading space width: 1,920 mm, loading space height: 415 mm, Year of construction: 2022, Equipment: ABS, * ETM-TA 14.4: ----Brakes: * Wabco ABS brake system * Emergency release mechanism for spring-loaded cylinders * Drum brakes ----Axles: * 2 x 7-ton Gigant axles ----Suspension: * Parabolic springs with tandem equalization unit ----Drawbar / Drawbar Eye: * Height-adjustable drawbar (+/- 150 mm) * 40 mm bolt-on drawbar eye ----General Attachments: Ncodpfxsl Th Dme Acysl * Jost landing gear at the front * Side underrun protection * Rear folding A-board ----Electrics / Lighting: * 15-pin power connector * Multi-chamber tail lights ----Body: * Fixed steel front and side walls * Removable steel rear wall * Floor made of 50 mm softwood * 1 sliding plate support 750 x 1,000 mm at the front section including 2 removable skip stops at the front, lockable in 2 positions * Rear traverse for attaching aluminium loading ramps, incl. 2 additional rear drop-down supports ----Loading Edge: * Unloaded loading edge approx. 710 mm ----Load Securing: * 4 removable skip stops, can be locked in 2 positions for side centering of skips * 1 x (13.5 t) UVV lashing point per side for attaching tie-down elements * 2 ratchet tensioners (spindle adjustment) with compensating chain and quick shortener (tensioning force 6,300 kg) ----Tyres: * Tyres: 285/70R19.5 ----Wheelbase: * Wheelbase: 1,140 mm ----Paintwork: * Chassis, front wall, side walls, mudguards, drawbar, rear drop-down supports hot-dip galvanized * Axles, springs, landing gear, and air reservoirs painted in black ----General Info: * Vehicle registered for one day in 06/2024, due to missing tyre pressure monitoring system; never loaded or used * Errors and prior sale excepted ----Delivery Time: * Immediately available ex Egestorf (A7)

Condition: new, maximum load weight: 10,800 kg, overall weight: 14,400 kg, axle configuration: 2 axles, loading space length: 6,270 mm, loading space width: 2,470 mm, Year of construction: 2025, * ETÜ-TA-R 14.4: ----Brakes: * EBS brake system * Emergency release device for spring brake cylinders * Drum brakes ----Axles: * 2 x 7 t Gigant axles ----Suspension: * Parabolic springs with compensating unit ----Drawbar / Flange Drawbar Eye: * Drawbar height-adjustable by 300 mm * Drawbar extension by 250 mm to a total length of 2,250 mm ----Electrics / Lighting: * Tire pressure monitoring with display option in the truck via EBS signal – without installation required on truck side Ncjdpfsxvgrijx Acyjl * 15-pin electrical connector * LED lighting system 12 / 24 V * EBS multi-voltage system for towing vehicles with 12 and 24 V electrics ----General Attachments: * Front support winch * External folding supports at the rear * Plastic toolbox approx. 858 x 500 x 500 mm on the right front exterior of the front wall * Side underrun protection * Plastic quarter mudguards ----Low Loader Platform: * 50 mm softwood floor * Provision in front of the front wall for retrofitting container locks * Bolted 400 mm smooth sheet front wall * Bolted rear stanchions * Drop sides with spring assists ----Load Securing: * Perforated outer frame, bent at approx. 45 degrees, with 2 t lashing capacity every 480 mm * Installation of 3 t recessed lashing rings possible every 600 mm * In each front and rear corner, 1 x 6.3 t lashing point * Various holes in the front and rear crossmember for 1.2 t lashing options ----Ramps: * One-piece hydraulic grating drive-on ramps approx. 2,750 x 600 mm (can be pushed together to 20 mm clearance) * Hydraulic flow divider in the trailer (for truck hydraulic output above 40 l/min up to max. 140 l/min) ----Paintwork: * Chassis, drawbar, front wall, mechanical drop supports, and drive-on ramps hot-dip galvanized * Axles, springs, air tanks, front support winch, and flange drawbar eye painted in a black tone * Drop sides painted RAL 2011 deep orange * Side panels available in a RAL color of your choice for an additional charge ----Information: * New vehicle with manufacturer’s warranty * Errors and prior sale excepted ----Delivery Time: * Available immediately ex Egestorf

Condition: used, maximum load weight: 31,000 kg, overall weight: 40,000 kg, axle configuration: > 3 axles, first registration: 07/2024, loading space length: 9,290 mm, loading space width: 2,520 mm, loading space height: 950 mm, * PT 40.0 profile: * Wabco EBS-E (electronic braking system) * Emergency release device for spring-loaded cylinders * Drum brakes * 4 x 11 tonne Gigant axles * Air suspension with lifting and lowering system and RtR valve * Manometer pressure indicator for determining load weight (axles separated into 2 air suspension circuits) * Side impact protection * Swivel supports at the rear of the chassis frame Ncjdpfx Ajl Tnu Ascyel * Mechanically adjustable warning sign packages at the front and rear * Front plastic quarter fender with splash guard * Rear straight galvanized. Sheet steel aprons with splash guard * Reflective contour tape on the side and rear * EBS multi-voltage system with 12 & 24 V electrics * 15-pin power plug * LED lighting system 12 / 24 V * LED rotating beacon (removable) at the rear * 2 LED reversing lights (switched via reverse gear) * Pull scissors with 50 mm pull eye and height adjustment * Tool box made of galvanized sheet steel, black powder-coated, approx. 1,000 mm wide, 600 mm deep, 300 mm high * Front section in front of the bogie platform approx. 490 mm long with 45° corners * ROBOT welded ANTI-SLIP coating for the steel plate of the bogie platform * La-Si package consisting of: in front of the front wall support on the left & right 1 x 13.4 ton each. UVV lashing eye, 4 holes on each side in the bogie platform with a lashing force of 2 tons each, 1 pair of lashing eyes (13.4 tons) hanging at the rear left and right in front of the rear carrier, 4 pairs of UVV lashing rings (10 tons) on each side, can be swiveled and lowered, can be loaded in all directions and embedded in the outer frame, 3 stake pockets on each side with a simultaneous 2 ton lashing option * Hot-dip galvanized mechanical folding boom for a total width of 3 meters (but not in the rear slope) * Plank holder for widening under the chassis on the left in the longitudinal direction * Excavator boom storage above the rear axle to the end carrier approx. 2,100 mm long and approx. 190 mm deep, 2 pairs of 6.4 tons on each side. Lashing rings in the excavator boom storage * Hardwood floor on the running surfaces of the low-loading platform * Hydraulic one-piece ramps (approx. 3,000 x 720 mm) mechanically laterally adjustable * Outer planks of the ramps made of hardwood * Steel construction in preparation for 6-way control slide * Loading edge unloaded approx. 950 mm +/+ 20 mm chassis * Bogie, folding boom, mechanical drop supports, ramps hot-dip galvanized * --Axles, air tank, pull scissors painted in a black tone-- * Tires 235/75 R 17.5 * Vehicle has a daily registration in 07/2024, due to missing tire pressure monitoring system and has not been loaded/used * New vehicle with manufacturer's warranty * Errors and prior sale subject to reservation * Available for immediate delivery from Egestorf

Condition: used, maximum load weight: 10,870 kg, overall weight: 14,400 kg, axle configuration: 2 axles, first registration: 06/2025, loading space length: 5,000 mm, loading space width: 2,420 mm, loading space height: 500 mm, Year of construction: 2023, Equipment: ABS, * KA-TA-R 14.4: * Wabco ABS * Emergency release device for spring-loaded cylinders * Drum brakes * 2 x 7 ton Gigant axles * Parabolic springs with tandem equalizer unit * Drawbar height adjustable by approx. 300 mm with 40 mm flange towing eye * Jost mechanical landing gear at the front * Two mechanical folding supports at the rear * Plastic toolbox approx. 650 x 350 x 320 mm, mounted at the front on the right side of the chassis * 15-pin power connector * Multi-chamber tail lights * Bolt-on underride guard * Plastic quarter mudguards * Net hooks at each position of the central locking and 2 hooks on the front wall * Chassis made of fine-grain steel * Steel pallet 3-way tipping body, continuous side walls at the top with internal pipe reinforcement - without central stanchions, foldable with drop-side spring lifter * Rear stanchions bolted * Combo steel swing doors at the rear, 2-wing asymmetrically split, can be swiveled and locked to 270° - not foldable - with additional pendulum frame for automatic tailgate opening during tipping process, locking via galvanized rotary bar lock at the rear and central locking, deactivation function for automatic tailgate during reverse tipping with opened swing door * Each corner with 1 x 5 ton lashing point and 4 x 3 ton lashing rings recessed into the outer frame on each side * 4 mm steel sheet floor made of fine-grain steel * Rear mounting rail for loading ramps * Reinforced body with load securing certificate Ncjdpfol Th Dusx Acysl * 1 pair of aluminum loading ramps approx. 3,570 x 410 mm (load capacity 10 tons per pair) suitable for rubber-tired & tracked vehicles * Lockable storage compartment from the rear recessed under the loading area in the chassis for the ramps * Chassis, drawbar, underride guard, rear stanchion, rear folding supports hot-dip galvanized * Axles, springs, air tank and landing gear painted black * Tires 285/70 19.5 * Side walls painted in RAL 9010 pure white * Painting of the side walls in a different RAL color available at extra cost * Vehicle has a day registration (unused) * Errors and prior sale excepted * Immediately available from Egestorf

Condition: new, maximum load weight: 10,800 kg, overall weight: 14,400 kg, axle configuration: 2 axles, loading space length: 6,270 mm, loading space width: 2,470 mm, Year of construction: 2025, * ETÜ-TA-R 14.4: ----Brakes: * EBS braking system * Emergency release device for spring-loaded cylinders * Drum brakes ----Axles: * 2 x 7 t Gigant axles ----Suspension: * Parabolic springs with compensating unit ----Drawbar / Flange Eye: * Drawbar height-adjustable by 300 mm * Drawbar extension by 250 mm to a total length of 2,250 mm ----Electrics / Lighting: * Tire pressure monitoring with display option in the truck via EBS signal - no installation on the truck required * 15-pin power connector * LED lighting system 12 / 24 V * EBS multi-voltage system for towing vehicles with 12 and 24 V electrics ----General Attachments: * Support winch at the front * Rear external foldable support legs * Plastic toolbox approx. 858 x 500 x 500 mm, mounted front right on the bulkhead * Side underrun protection * Plastic quarter mudguards ----Low Loader Area: Njdpforwc R Rjx Acyecl * 50 mm softwood floor * Preparation for subsequent installation of container locks in front of the bulkhead * 400 mm high bolted smooth sheet metal bulkhead * Removable and bolted rear stanchions * Side panels with spring-assisted lifting mechanism ----Load Securing: * Perforated outer frame, angled at approx. 45 degrees, with 2 t lashing capacity every 480 mm * Option to install 3 t fold-down lashing rings every 600 mm * One 6.3 t lashing ring front and rear in each corner * Various holes in the front and rear cross member for 1.2 t lashing capability ----Ramps: * Single-piece hydraulic grid drive-on ramps, approx. 2,750 x 600 mm (can be pushed together to 20 mm) * Hydraulic flow divider in the trailer (for hydraulic pump output in the truck over 40 l/min up to max. 140 l/min) ----Paintwork: * Chassis, drawbar, bulkhead, mechanical drop-down supports, and drive-on ramps hot-dip galvanized * Axles, springs, air tank, front support winch, and flange eye painted in black * Side panels painted in RAL 9010 pure white * Painting of the side walls in a RAL color available at extra charge ----Information: * New vehicle with manufacturer's warranty * Subject to error and prior sale ----Delivery Time: * Available immediately ex Egestorf

Condition: used, maximum load weight: 31,000 kg, overall weight: 40,000 kg, axle configuration: > 3 axles, first registration: 07/2024, loading space length: 9,290 mm, loading space width: 2,520 mm, loading space height: 950 mm, * PT 40.0 profile: * Wabco EBS-E (electronic braking system) * Emergency release device for spring-loaded cylinders * Drum brakes * 4 x 11 tonne Gigant axles * Air suspension with lifting and lowering system and RtR valve * Manometer pressure indicator for determining load weight (axles separated into 2 air suspension circuits) * Side impact protection * Swivel supports at the rear of the chassis frame * Mechanically adjustable warning sign packages at the front and rear * Front plastic quarter fender with splash guard * Rear straight galvanized. Sheet steel aprons with splash guard * Reflective contour tape on the side and rear * EBS multi-voltage system with 12 & 24 V electrics * 15-pin power plug * LED lighting system 12 / 24 V * LED rotating beacon (removable) at the rear * 2 LED reversing lights (switched via reverse gear) * Pull scissors with 50 mm pull eye and height adjustment * Tool box made of galvanized sheet steel, black powder-coated, approx. 1,000 mm wide, 600 mm deep, 300 mm high * Front section in front of the bogie platform approx. 490 mm long with 45° corners * ROBOT welded ANTI-SLIP coating for the steel plate of the bogie platform * La-Si package consisting of: in front of the front wall support on the left & right 1 x 13.4 ton each. UVV lashing eye, 4 holes on each side in the bogie platform with a lashing force of 2 tons each, 1 pair of lashing eyes (13.4 tons) hanging at the rear left and right in front of the rear carrier, 4 pairs of UVV lashing rings (10 tons) on each side, can be swiveled and lowered, can be loaded in all directions and embedded in the outer frame, 3 stake pockets on each side with a simultaneous 2 ton lashing option * Hot-dip galvanized mechanical folding boom for a total width of 3 meters (but not in the rear slope) * Plank holder for widening under the chassis on the left in the longitudinal direction * Excavator boom storage above the rear axle to the end carrier approx. 2,100 mm long and approx. 190 mm deep, 2 pairs of 6.4 tons on each side. Lashing rings in the excavator boom storage * Hardwood floor on the running surfaces of the low-loading platform * Hydraulic one-piece ramps (approx. 3,000 x 720 mm) mechanically laterally adjustable * Outer planks of the ramps made of hardwood * Steel construction in preparation for 6-way control slide * Loading edge unloaded approx. 950 mm +/+ 20 mm chassis * Bogie, folding boom, mechanical drop supports, ramps hot-dip galvanized * --Axles, air tank, pull scissors painted in a black tone-- Nsdpfol Tlhrox Acyocl * Tires 235/75 R 17.5 * Vehicle has a daily registration in 07/2024, due to missing tire pressure monitoring system and has not been loaded/used * New vehicle with manufacturer's warranty * Errors and prior sale subject to reservation * Available for immediate delivery from Egestorf

Condition: used, maximum load weight: 8,650 kg, overall weight: 11,900 kg, axle configuration: 2 axles, first registration: 10/2016, Equipment: ABS, Welcome to Johanning’s Commercial Vehicles, your specialist for young and exclusive used vehicles. AVAILABLE IMMEDIATELY! Delivery possible. Price on request! Financing & leasing available upon request. Location: 39606 Osterburg, incoming stock! Make: Mueller Mitteltal Model: TA-2 / ETUE-TA-R 11.9 Year of manufacture: 2016 Operating weight: 3,250 kg Inspection (TÜV): March 2026 Safety inspection (SP): September 2026 For additional photos or videos, feel free to ask. Johanning’s Commercial Vehicles – your partner for exclusive and young used vehicles. Our services – your advantages: (after purchase) - Trade-in of your vehicle possible (any condition) - Immediate deregistration of your vehicle free of charge - Registration service for €150 (including fees and license plates) - Short-term registration available - Viewing and test drive possible at any time by telephone appointment - Free delivery by arrangement possible. Nodpfxoycpd Ao Acyocl Subject to errors and prior sale.

Condition: used, maximum load weight: 5,000 kg, overall weight: 7,200 kg, axle configuration: 2 axles, first registration: 04/1979, Year of construction: 1979, 3-way tipper trailer in 80 km/h version, 2-circuit air brake system, rear towing hitch with hydraulic connection and brake connections for an additional trailer. Steel side panels. According to the owner, the trailer is in good functional condition! Sold as is, without TÜV, on behalf of the customer. Cash price €3,900. Nedpfx Aoxzzglocyscl

Condition: like new (used), functionality: fully functional, empty load weight: 4,730 kg, maximum load weight: 13,270 kg, overall weight: 18,000 kg, axle configuration: 2 axles, next inspection (TÜV): 03/2026, loading space length: 6,270 mm, loading space width: 2,540 mm, total length: 8,520 mm, total width: 2,540 mm, total height: 3,500 mm, tire size: 235 75 R17,5, tire condition: 90 %, Year of construction: 2022, The central axle trailer by Müller Mitteltal is in very good, lightly used condition with an unladen weight of 4,730 kg, payload of 13,270 kg, gross weight of 18 t, length 8,520 mm, width 2,540 mm, height 3,500 mm. It is a twin-axle trailer with twin wheels, air suspension, and galvanized frame. VAT not deductible. Nodpeyc Hghjfx Acyocl

Condition: new, maximum load weight: 10,950 kg, overall weight: 14,400 kg, axle configuration: 2 axles, loading space length: 6,270 mm, loading space width: 2,470 mm, Year of construction: 2026, Equipment: ABS, tail-lift, Müller-Mitteltal ETÜ-TA-R 14.4 Tandem ? Low Loader ? Platform ? Trailer Available at the end of February ’26 | Ref. No. for inquiries: 27678 | Free delivery to your address possible * We are happy to provide you with an individual offer * ---- * Gross weight: 14.4 t, Payload: 10.95 t * LED lighting system * GIGANT axles, EBS, twin tires 235/75R 17.5, parabolic springs * Tire pressure monitoring system (TPMS) * 6.27 m x 2.47 m platform with galvanized front wall, 400 mm high * Hardwood excavator bucket rest bolted to the front wall * Deck height unladen 930 mm / laden 870 mm * One-piece ramps with hot-galvanized grating, anti-slip design, extendable to approx. 20 mm, secured by support rods and diagonal bracing * Ramp lifter with vertically mounted, adjustable springs for easy single-person operation * 4 UVV drop lashing rings (LC 6300 daN) * Perforated outer frame (45° bent with hole pattern for lashing equipment, lashing force per point LC 2000 daN, min. spacing of 480 mm. Installation of drop lashing rings LC 3000 daN with approx. 600 mm spacing possible) with closely spaced cross-members, high-profile front and rear ends, rear incline, hot-galvanized * 10 UVV flush-mount lashing rings LC 3000 daN can be recessed into existing hole pattern in the outer frame, in addition * Additional lashing points via holes (Ø 50 mm, LC 1200 daN) in front and end crossmembers * Toolbox in front of the bulkhead * Side marker lights with indicator function * 50 mm thick softwood floor. Chassis hot-galvanized * 2 recessed container locks in front crossmember * Height-adjustable support winch at front, drop-down supports at rear * Drawbar with 40 mm towing eye (hot-dip galvanized), height-adjustable, optionally available with 50 mm towing eye * 1 removable LED beacon at the rear---- * Leasing, hire purchase, financing, trade-in possible * e.g. €515 per month with 60 months term – no down payment, no residual value * ---- * Our opening hours * Monday - Thursday: 08:00 - 17:00 * Friday: 08:00 - 15:00 Nodpfoyadz Rex Acyjcl Outside these hours, we are available by appointment. We speak German, English, Polish, and French. Leasing, financing, and trade-in available.

Condition: used, maximum load weight: 13,820 kg, overall weight: 18,000 kg, axle configuration: 2 axles, first registration: 07/2020, next inspection (TÜV): 10/2026, loading space length: 5,000 mm, loading space width: 2,380 mm, loading space height: 900 mm, total width: 2,550 mm, total height: 2,450 mm, Equipment: ABS, Tandem three-way tipper trailer ABS Air suspension Support leg at front Platform at front wall Aluminum drop sides Nedpfx Aceyawayeyscl Foldable underrun protection Wheelbase 1,000 mm Gross weight 18,000 kg Payload 13,820 kg Tyres 385/65R22.5, 40-80% tread Vehicle No. 2428 for inquiries. Trailer in very good overall condition, first owner. No liability for typing or data transmission errors. Subject to change and prior sale. Daily cash purchase of commercial vehicles, construction machinery, trailers, and semi-trailers built from 2000-2025.

Condition: used, maximum load weight: 7,090 kg, overall weight: 9,990 kg, axle configuration: 2 axles, first registration: 05/1999, loading space length: 4,530 mm, loading space width: 2,400 mm, loading space height: 850 mm, total width: 2,550 mm, Gross weight: 9,990 kg Unladen weight: 2,900 kg Payload: 7,090 kg Overall length: 6,400 mm Loading length: approx. 4,530 mm Width: 2,550 mm / Loading width approx. 2,400 mm Loading height: approx. 850 mm Further information: Nodpfxox Uv D Ue Acyecl - 400 mm sideboards, foldable - 8 lashing eyes - BPW axles

Condition: new, maximum load weight: 6,810 kg, overall weight: 9,600 kg, axle configuration: 1 axle, loading space length: 4,030 mm, loading space width: 2,420 mm, loading space height: 700 mm, Year of construction: 2025, * EK 9.6 ----Brakes: * EBS (electronic braking system) * Emergency release device for spring brake cylinders * Drum brakes ----Axle: * SAF axle ----Suspension: * Parabolic springs ----Drawbar / Towing Eye: * Drawbar as a center axle with 40 mm bolted towing eye * Continuously adjustable drawbar height with spindle lifting element instead of a fixed drawbar ----Coupling Height: * Standard coupling height approx. 900 mm (+/- 150 mm) ----Electrics / Lighting: * Tire pressure monitoring with display option in the truck via EBS signal – no installation required on the truck side * 15-pin power connector * LED tail lights Njdpfew Ndr Uox Acyecl * Flashing side marker lamps ----General Attachments: * Support windlass at the front * Enclosed plastic mudguards * Folding underrun protection for paver ----Chassis: * Chassis made of fine-grained steel ----Tipper Body: * Pal.- 3-way tipper body * 700 mm steel front wall * Continuous aluminium side walls, asymmetrical, foldable down without center stanchion, with long-path fasteners and swinging function via manual central locking * 800 mm high steel rear wall with automatic rear wall opening during tipping towards the rear * 4 mm Hardox 450 steel floor ----Load Securing: * Two pairs of 3 t lashing rings per side, sunk and foldable in the steel floor ----Paintwork: * Chassis, drawbar, underrun protection hot-dip galvanized * Tipper body painted in RAL 9010 pure white ----Information: * New vehicle with manufacturer's warranty * Subject to errors and prior sale ----Delivery Time: * Immediately available ex Egestorf

Condition: new, maximum load weight: 10,760 kg, overall weight: 14,400 kg, axle configuration: 2 axles, loading space length: 6,270 mm, loading space width: 2,470 mm, loading space height: 400 mm, Year of construction: 2026, * ETÜ-TA-R 14.4: Ncedpfx Acjrvvfleysl * RDÜ (Tire Pressure Monitoring System) * Electronic Braking System (EBS) * Emergency Release Device for Spring Brake Cylinders * LED Lighting * Drum Brakes * 2 x 7-ton Gigant Axles * Parabolic Springs with Equalizer * Height-adjustable Drawbar by 300 mm * Drawbar Extension by 250 mm to 2,250 mm * Jost Landing Gear at the Front * Externally Mounted, Hot-dip Galvanized Folding Support Legs at the Rear * Plastic Toolbox, Front Right, on Bulkhead * Side Underrun Protection * Plastic Quarter Mudguards * Hot-dip Galvanized Chassis and Drawbar * Front Bulkhead * Rear Wall * Tailgate and Loading Ramps * 50 mm Softwood Floor * Preparation in Front of Bulkhead for Subsequent Installation of Container Locks * Bolted Bulkhead from Smooth Sheet Metal * Trapezoidal-profile Fold-down Steel Sidewalls with Sideboard Spring Assist * Slide-in Steel Rear Wall between the Ramps—mounting bracket for storage inside the front bulkhead when not in use * Bolted Rear Stanchions * Perforated Outer Frame, approx. 45-degree angled, with 2 t lashing capacity every 480 mm; possible installation of 3 t recessed lashing rings every 600 mm; 1 x 6.3 t lashing point in each front and rear corner; various drillings for 1.2 t lashing options on the front and end cross members * One-piece Mechanical Grid Loading Ramps with Spring Mechanism for Single-person Operation, approx. 2,750 x 600 mm (collapsible to 20 mm) * Rear Entry Slope approx. 860 mm * --Reinforced and Certified Structure according to EN 12642 XL including Load Securing Certificate-- * Sideboard Color in RAL 9010 Pure White * Sidewall Painting in Any RAL Color Available at Extra Cost * New Vehicle with Manufacturer’s Warranty * Subject to Errors and Prior Sale * Available from Calendar Week 08/2026

Condition: new, maximum load weight: 10,760 kg, overall weight: 14,400 kg, axle configuration: 2 axles, loading space length: 6,270 mm, loading space width: 2,470 mm, loading space height: 400 mm, Year of construction: 2026, * ETÜ-TA-R 14.4: * RDÜ (Tire Pressure Monitoring System) * Electronic braking system (EBS) * Emergency release mechanism for spring-loaded brake cylinders * LED lighting * Drum brakes * 2 x 7-ton Gigant axles * Parabolic springs with compensating unit * Height-adjustable drawbar, adjustable by 300 mm * Drawbar extension by 250 mm to a total of 2,250 mm * Jost landing gear at the front * Externally mounted hot-dip galvanized foldable supports at the rear * Plastic toolbox, front right outside on the front wall * Side underrun protection Ncjdpfx Acoxglibjysl * Plastic quarter mudguards * Hot-dip galvanized chassis and drawbar * Front wall * Rear wall * Tailgate and loading ramps * 50 mm softwood floor * Fixture in front of the front wall for retrofitting container locks * Bolted front wall made of smooth sheet metal * Side walls made of trapezoidal-profiled steel sheet, foldable, with drop-side spring assist * Steel rear wall, slidable between the ramps—storage bracket inside at the front wall when not in use * Bolted rear stanchions * Perforated outer frame, bent at approx. 45 degrees, with 2-ton lashing capacity every 480 mm, installation of 3-ton folding lashing rings possible every 600 mm, 1 x 6.3-ton lashing ring in each front and rear corner, various holes in the front and end crossmember for 1.2-ton lashing options * One-piece mechanical grating ramps with spring mechanism for one-man operation, approx. 2,750 x 600 mm (can be pushed together to 20 mm) * Rear approach slope approx. 860 mm * --Reinforced and certified body according to EN 12642 XL incl. load securing certificate-- * Drop side color in RAL 2011 deep orange * New vehicle with manufacturer’s warranty * Errors and prior sale excepted * Available from calendar week 08/2026 * Sample images

Condition: new, maximum load weight: 10,760 kg, overall weight: 14,400 kg, axle configuration: 2 axles, loading space length: 6,270 mm, loading space width: 2,470 mm, loading space height: 400 mm, Year of construction: 2026, * ETÜ-TA-R 14.4: * RDÜ (tire pressure monitoring system) * Electronic braking system (EBS) * Emergency release device for spring brake cylinders * LED lighting * Drum brakes * 2 x 7 t Gigant axles * Parabolic springs with equalizer unit * Drawbar adjustable in height by 300 mm * Drawbar extension of 250 mm to a total of 2,250 mm * Jost landing gear at the front * Externally mounted hot-dip galvanized folding supports at the rear * Plastic toolbox at front right, mounted on the front wall Njdpfxsq Dyvvo Acyscl * Side underrun protection * Plastic quarter mudguards * Hot-dip galvanized chassis and drawbar * Front wall * Rear wall * Tailgate and loading ramps * 50 mm softwood floor * Provision in front of the front wall for retrofitting container locks * Bolted smooth sheet metal front wall * Side walls made of trapezoidal profile steel, fold-down with drop side spring assist * Steel rear wall, can be inserted between the ramps – storage bracket inside at the front wall when not in use * Bolted rear stanchions * Perforated outer frame, edged at approx. 45 degrees, with 2 t lashing capacity every 480 mm. Installation of 3 t folding lashing rings every 600 mm possible. Each front and rear corner with 1 x 6.3 t lashing ring; multiple 1.2 t lashing points in the front and rear crossmember. * One-piece mechanical grating loading ramps with spring system for single-person operation, approx. 2,750 x 600 mm (can be retracted to 20 mm) * Rear approach angle approx. 860 mm * Reinforced and certified body according to EN 12642 XL including load securing certificate * Drop-side color in RAL 9010 pure white * Painting of side walls in a RAL color of your choice available for a surcharge * New vehicle with manufacturer's warranty * Subject to alteration and prior sale * Available from calendar week 08/2026

Condition: new, maximum load weight: 10,760 kg, overall weight: 14,400 kg, axle configuration: 2 axles, loading space length: 6,270 mm, loading space width: 2,470 mm, loading space height: 400 mm, Year of construction: 2026, * ETÜ-TA-R 14.4: * RDÜ (Tire Pressure Monitoring System) Ncsdpfx Aoxglh Rscyjl * Electronic braking system (EBS) * Emergency release device for spring brake cylinders * LED lighting * Drum brakes * 2 x 7-ton Gigant axles * Parabolic leaf springs with balancing unit * Tow bar height adjustable by 300 mm * Tow bar extension by 250 mm to 2,250 mm * Jost landing gear at the front * Externally mounted, hot-dip galvanized folding supports at the rear * Plastic toolbox at the front right outside on the bulkhead * Side underrun protection * Plastic quarter mudguards * Hot-dip galvanized chassis and tow bar * Front wall * Rear wall * Tailgate and loading ramps * 50 mm softwood floor * Preparation in front of the bulkhead for retrofitting container locks * Bolted bulkhead made from smooth sheet metal * Side walls made of trapezoidal-profiled steel sheet, foldable with drop side lift assist * Steel rear wall, can be inserted between the ramps, storage bracket for non-use inside at the front bulkhead * Bolted rear stanchions * Perforated outer frame approx. 45 degrees bent, with 2-ton lashing capacity every 480 mm; installation of 3-ton drop lashing rings every 600 mm possible; in each front and rear corner 1 x 6.3-ton lashing ring; various holes for 1.2-ton lashing options in the front and rear crossmembers * One-piece mechanical grating loading ramps with spring mechanism for one-man operation approx. 2,750 x 600 mm (can be retracted to 20 mm) * Rear drive-on slope approx. 860 mm * -- Reinforced and certified bodywork according to EN 12642 XL including load securing certificate -- * Drop side color in RAL 2011 deep orange * New vehicle with manufacturer's warranty * Subject to errors and prior sale * Available from week 08/2026 * Sample images

Condition: new, maximum load weight: 31,630 kg, overall weight: 40,000 kg, axle configuration: > 3 axles, loading space length: 9,250 mm, loading space width: 2,520 mm, * T 4: * EBS (Electronic Braking System) * Emergency release device for spring-loaded cylinders * Drum brakes * 4 x 11 t Gigant axles * Parabolic springs * Mechanical axle compensation front and rear * Tire pressure monitoring with display option in the truck via EBS signal – no truck-side installation required * Warning sign packages front and rear * Side and rear contour marking tape, reflective * EBS multi-voltage system for 12 & 24 V electrics * LED beacon (removable) at the rear * 24 V – 15-pin and additional 12 V – 7+4 pin power cable * Extended connection cables for agricultural and forestry tractors * LED lighting * Straight drawbar with 40 mm towing eye and stepless height adjustment * Tool box made of powder-coated steel sheet, plus basket-type spare wheel holder on the right side * Closed single plastic fenders at the front * Straight steel mudguards at the rear, each with splash protection (spray suppression) * Side underrun protection * Extended offset bend by 500 mm to the front * Turntable platform extended by 520 mm at the front with 45° corners and 3 recessed lockable storage compartments including lids * Chassis made of high-strength fine-grained steel * Deck over the turntable platform made of 50 mm and on the low-bed platform made of 60 mm softwood * Outer planks of the loading ramps made of 50 mm bamboo wood Ncjdpol Th Evjfx Acyjl * 4 stanchion pockets on each side (without stanchions) with simultaneous 2 t lashing option * Load securing package consisting of: 2 tie-down eyes 6.4 t front left and right on the main frame of the turntable platform, 1 pair each of 13.4 t lashing rings at the front and rear side frames, 4 pairs each side of 10 t foldable and lowerable lashing rings, loadable in all directions and recessed in the outer frame, 2 pairs of 6.4 t lashing rings on the excavator arm rest, 8 pairs of galvanized fold-out outriggers for 3 m total width (not at the rear slope) * Widening planks stored in a side left compartment * Excavator arm rest above the rear axle up to the end of the inclined rear approx. 2,300 x 740 x 190 mm * Mechanical drop legs at the rear * Hydraulic, hot-dip galvanized loading ramps approx. 3,000 x 720 mm * Hydraulic lateral ramp shifting on sliding tube from the ramp shaft * Loading area above the turntable: approx. 2,990 x 2,520 mm * Rear loading area: approx. 6,280 x 2,520 mm * Loaded loading height approx. 860 mm (incl. 860 mm ascending slope) * Chassis, turntable, loading ramps, mechanical rear drop legs hot-dip galvanized * Axles, springs, air tanks and turntable painted in black tone * New vehicle with manufacturer warranty * Subject to errors and prior sale * Available from CW 14 / 2026

Condition: new, maximum load weight: 31,630 kg, overall weight: 40,000 kg, axle configuration: > 3 axles, loading space length: 9,250 mm, loading space width: 2,520 mm, * T 4: * EBS (Electronic Braking System) * Emergency release device for spring brake cylinders * Drum brakes * 4 x 11 t Gigant axles * Parabolic springs * Mechanical axle compensation front and rear * Tire pressure monitoring with display option in the truck via EBS signal – no installation required on the truck side * Warning sign packages front & rear * Reflective contour tape on sides and rear * EBS multi-voltage system for 12 & 24 V electrics * Removable rear LED beacon * 24 V 15-pin and additional 12 V 7+4-pin power cables * Extended connection cables for agricultural and forestry towing vehicles * LED lighting * Straight drawbar with 40 mm towing eye and stepless height adjustment * Powder-coated steel toolbox and wire basket-type spare wheel holder, mounted right side * Closed single plastic mudguards at the front * Straight steel rear mudflaps each with spray suppression * Side underrun protection * 500 mm extended offset crank to the front * Turntable platform extended by 520 mm front with 45° corners and 3 integrated lockable storage compartments incl. lids * Chassis made of high-strength fine-grained steel * Decking above turntable platform: 50 mm, low-bed platform: 60 mm coniferous wood * Outer planks of ramps in 50 mm bamboo wood * Four stake pockets each side (no stakes supplied) with 2 t lashing option per pocket * Lashing package includes: 2 x 6.4 t lashing eyes front left and right on the main frame of the turntable platform, 1 pair of 13.4 t lashing rings on the outer frame front and rear on each side, 4 pairs of 10 t swivel and drop lashing rings per side, loadable in all directions and recessed into the outer frame, 2 pairs of 6.4 t lashing rings in the excavator arm rest area, 8 pairs of galvanized folding extenders for 3 m overall width (not fitted on rear incline) Ncsdjrczm Djpfx Acyol * Spreader boards stowed on left side in compartment * Excavator arm rest above rear axle to end of rear incline approx. 2,300 x 740 x 190 mm * Mechanical drop-down supports at rear * Hydraulic, hot-dip galvanized loading ramps approx. 3,000 x 720 mm * Hydraulic lateral ramp shift on sliding tube from ramp shaft * Loading area above turntable: approx. 2,990 x 2,520 mm * Rear loading area: approx. 6,280 x 2,520 mm * Loaded platform height approx. 860 mm (incl. 860 mm rear incline) * Chassis, turntable, ramps, and rear mechanical folding supports hot-dip galvanized * Axles, springs, air tanks, and turntable painted in shade of black * New vehicle with manufacturer’s warranty * Errors and prior sale excepted * Available from CW 14 / 2026

Condition: used, maximum load weight: 28,700 kg, overall weight: 40,000 kg, axle configuration: > 3 axles, first registration: 09/2013, next inspection (TÜV): 09/2026, total width: 2,550 mm, Equipment: ABS, You can find our complete vehicle inventory, including vehicles available immediately or at short notice, on our website. Excerpt from the equipment list. Full equipment details available on request. * Excavator bucket well, approx. 2,800 x 770 x 280 mm * 2-piece hydraulic ramps, approx. 2,100 x 2,100 x 700 mm, hydraulically adjustable * Hydraulic rear supports * Hydraulic lifting bed, approx. 4,020 mm long * Partial rubber coating on the loading area and ramps * Drive-over plate for ramps * Extendable loading area * Wabco Smartboard * Air suspension with lifting and lowering function * 2 work lights on the ramps * Hydraulic connections for the towing vehicle * 15-pin socket + ABS * 50 mm towing eye * BPW axles Ncjdpfxex Tx Elj Acyol * Gooseneck with wooden cover * Storage box with lid integrated in the gooseneck

Condition: new, maximum load weight: 10,400 kg, overall weight: 14,400 kg, axle configuration: 2 axles, loading space length: 5,500 mm, loading space width: 2,420 mm, loading space height: 500 mm, Year of construction: 2026, * ETK-TA-R 14.4: ----Brakes: * EBS (Electronic Braking System) * Emergency release device for spring brake cylinders * Drum brakes ----Axle: * 2 x 7 t Gigant axles ----Suspension: * Parabolic springs with tandem equalizer unit ----Drawbar / Flange Drawbar Eye: * Height-adjustable drawbar, adjustable by 300 mm with 40 mm flange drawbar eye ----Electrics / Lighting: * Tyre pressure monitoring with display option in the truck via EBS signal, no truck-side installation required * 15-pin power connector * LED tail lights ----General Attachments: * Mechanical support winch at front * 2 mechanical folding supports at rear * Plastic toolbox approx. 750 x 350 x 300 mm, mounted right side * Bolted underrun protection * Plastic quarter mudguards ----Frame: * Main frame made of fine-grain steel ----Tipping Platform: * Net hooks on the sides and rear at the central locking brackets as well as 2 hooks on the front wall * Steel pallet two-way tipper structure; fixed front wall made of smooth sheet, continuous drop sides (foldable without central stanchions, equipped with drop side spring keepers) and pendulum function via manual central locking * Removable rear stanchions (bolted) * Steel rear panel inserted in front of the ramps * Each corner equipped with 1 x 5 t lashing point plus 4 x 3 t lashing rings integrated in the outer frame on each side * 4 mm floor made of fine-grain steel ----Ramps: * Two-part mechanical grating loading ramps with aluminium tip section, 2,150 + 1,300 mm x 600 mm (manually retractable to a total of 80 mm) ----Paintwork: * Chassis, drawbar, rear stanchions, underrun protection, mechanical supports, and loading ramps hot-dip galvanized * Axles, springs, air tanks, flange drawbar eye, and support winch painted in black tone * Drop sides and platform in RAL 9010 pure white * Painting of the side walls and tipping platform in a RAL color shade available at extra cost ----Notes: * New vehicle with manufacturer’s warranty * Subject to errors and prior sale ----Delivery Time: Njdpfx Acetr Sucjyjcl * Available from calendar week 07/2026

Condition: new, maximum load weight: 10,400 kg, overall weight: 14,400 kg, axle configuration: 2 axles, loading space length: 5,500 mm, loading space width: 2,420 mm, loading space height: 500 mm, Year of construction: 2026, * ETK-TA-R 14.4: Ncsdpfx Aetr St Uscyjl ----Brakes: * EBS (Electronic Braking System) * Emergency release device for spring-actuated cylinders * Drum brakes ----Axle: * 2 x 7 t Gigant axles ----Suspension: * Parabolic springs with tandem equalizer assembly ----Drawbar / Flange Drawbar Eye: * Height-adjustable drawbar (range 300 mm) with 40 mm flange drawbar eye ----Electrics / Lighting: * Tire pressure monitoring with display capability in the truck via EBS signal, no truck-side installation required * 15-pin power connector * LED tail lights ----General Attachments: * Mechanical landing gear at the front * Two mechanical folding supports at the rear * Plastic toolbox approximately 750 x 350 x 300 mm, mounted on the right side * Bolted underrun protection * Plastic quarter mudguards ----Frame: * Main frame made of high-tensile fine-grained steel ----Tipping Platform: * Mesh hooks on the sides and rear at the central locking mounts, plus 2 hooks on the front wall * 2-way steel pallet tipper body with fixed smooth sheet metal front wall, continuous drop sides – foldable without center posts with board lifting springs, and swinging via manual central locking * Rear posts bolted * Steel rear wall inserted in front of the ramps * Each corner with 1 x 5 t lashing point, and 4 x 3 t lashing rings embedded in the outer frame on each side * 4 mm floor made of high-tensile fine-grained steel ----Ramps: * Two-part mechanical mesh drive-up ramps with aluminum tip section, 2,150 + 1,300 mm x 600 mm (can be manually slid together to 80 mm) ----Paintwork: * Chassis, drawbar, rear posts, underrun protection, mechanical supports, and ramps hot-dip galvanized * Axles, springs, air tanks, flange drawbar eye, and landing gear painted in black * Sideboards and platform in RAL 9010 pure white * Paintwork of sidewalls and tipping platform in any RAL color available at extra cost ----Information: * New vehicle with manufacturer's warranty * Subject to errors and prior sale ----Delivery time: * Available from week 07/2026

Condition: new, maximum load weight: 10,750 kg, overall weight: 14,400 kg, axle configuration: 2 axles, loading space length: 7,000 mm, loading space width: 2,470 mm, loading space height: 400 mm, Year of construction: 2025, * ETÜ-TA-R 14.4: ----Brake system: * EBS (Electronic Braking System) * Emergency release device for spring-loaded cylinders * Drum brakes ----Axle: * 2 x 7 t Gigant axles ----Suspension: * Parabolic springs with compensation unit ----Drawbar / Flange towing eye: * Drawbar height adjustable by 300 mm * Drawbar extension by 250 mm to 2,250 mm * 40 mm flange towing eye ----Electrics / Lighting: * TPMS (Tire Pressure Monitoring System) * 15-pin electrical connector * LED lighting Ncsdpfxov D Tcbe Acyol ----General attachments: * Support winch at the front * External folding support legs at the rear * Plastic toolbox approx. 858 x 500 x 500 mm, mounted outside front right on the front wall * Side underride protection * Plastic quarter mudguards ----Low-loader deck: * 50 mm softwood flooring * Pre-fitted fixtures on the front wall and at the rear incline for subsequent installation of container locks for transporting 20" containers * Bolted front wall made from smooth sheet metal * Side walls made of folded steel sheet – trapezoidal profile – foldable, split once in the centre * Rear wall made of steel, can be slid in between the ramp holders, stowed inside in front of the front wall when not in use * Rear stanchions bolted ----Load securing: * Perforated outer frame bent to approx. 45 degrees with 2 t lashing capacity every 480 mm * Installation of 3 t folding lashing rings every 600 mm possible * 1 x 6.3 t lashing ring in each front and rear corner * Several holes in the front and rear cross members for 1.2 t lashing points ----Ramps: * One-piece mechanical mesh-access ramps with spring mechanism for single-person operation, approx. 2,750 x 600 mm (collapsible to 20 mm) * Rear approach angle approx. 860 mm chassis ----Wheelbase: * Wheelbase 1,140 mm ----Paint finish: * Drawbar, front wall, tailgate, folding supports and access ramps hot-dip galvanized * Axles, springs, air tanks, flange towing eye, and support winch painted in black * Side boards painted RAL 9010 pure white * Side walls can be painted in a RAL colour of your choice at extra cost ----Information: * Reinforced and certified body according to EN 12642 XL incl. load securing certificate * New vehicle with manufacturer's warranty * Subject to errors and prior sale ----Delivery time: * Available immediately from Egestorf at the A7