Used Müller-Mitteltal Roll-Off Trailers for sale (267)

Condition: new, maximum load weight: 10,360 kg, overall weight: 14,400 kg, axle configuration: 2 axles, loading space length: 6,270 mm, loading space width: 2,470 mm, loading space height: 400 mm, Year of construction: 2025, * ETÜ-TA-ER 14.4: ----Brakes: * Electronic Braking System (EBS) * Emergency release device for spring brake cylinders * Drum brakes ----Axles: * Gigant axles ----Suspension: * Air suspension with lifting and lowering function ----Drawbar / Flange Towing Eye: * Drawbar height adjustable by 300 mm * 40 mm flange towing eye ----Electrics / Lighting: * Tire Pressure Monitoring System (TPMS) with display capability in the truck via EBS signal, no truck-side installation required * LED lighting system * 15-pin power connector ----General Attachments: * Jost landing gear at the front * Externally mounted, hot-dip galvanized, folding rear supports * Plastic toolbox mounted on the front right exterior of the bulkhead * Lateral underrun protection Nodpfx Agondpn Sexsda * Plastic quarter mudguards ----Low Loader Platform: * 50 mm softwood flooring * Pre-installed fittings for later mounting of 20" container locks front and rear * Bolted smooth sheet steel front wall * Trapezoidal profile steel sheet side walls, foldable with drop side spring assist * Bolted, hot-dip galvanized rear stanchions ----Load Securing: * Perforated outer frame, approx. 45° bent, with 2 t lashing force every 480 mm * Installation of 3 t folding lashing rings every 600 mm possible * One 6.3 t lashing ring in each front and rear corner * Various holes in the front and rear cross members for 1.2 t lashing options ----Ramps: * 1 pair aluminum loading ramps, approx. 3,310 x 400 mm (load capacity 8 t / pair), suitable for rubber-tired and tracked vehicles, stowed from the rear in a compartment recessed under the loading area in the chassis ----Painting: * Hot-dip galvanized chassis, drawbar, front wall and rear wall * Complete vehicle hot-dip galvanized ----Info: * New vehicle with manufacturer's warranty * Subject to alteration and prior sale ----Delivery Time: * Available immediately ex Egestorf

Condition: new, maximum load weight: 30,440 kg, overall weight: 40,000 kg, axle configuration: > 3 axles, Year of construction: 2026, Equipment: ABS, T 4 Profi 40.0 ----Brakes: * Wabco EBS-E (electronic braking system) * Emergency release system for spring-loaded cylinders * Drum brakes ----Axles: * 4 x 11-ton Gigant axles ----Suspension: * Air suspension with lifting and lowering system and RtR valve ----Drawbar: Ndodpfxeylfvge Agxea * Straight drawbar with 50 mm drawbar eye and stepless height adjustment ----Electrical System / Lighting: * Tire pressure monitoring system with display option in the truck display via EBS signal - without truck-side installation - * SmartBoard as an information tool with pressure sensors for axle load display per axle group * 15-pin power connector * LED rear lights * LED marker lights (removable) at the rear ----General Components: * Warning sign packages at the front & rear * 2 x toolboxes made of galvanized, powder-coated steel sheet, approx. 650 x 300 x 600 mm, on the right side * Closed plastic fender at the front * Straight steel mudguards at the rear, each with splash protection (spray mist suppression) * Lateral impact protection ----Low-bed Platform: * Extension of the turntable platform by 520 mm with 45° corners and 3 recessed storage compartments incl. lids and locking mechanism * Floor over the turntable platform made of 50 mm needlewood, and in the low-bed platform made of 60 mm needlewood * Rubber coating 20 mm instead of wooden floor in the running area with a low-bed length of 6,780 mm including the access ramp * Rubber coating on the access ramp, left and right, approx. 860 mm long * 4 lashing eye pockets on each side (however, no lashing bars included) with simultaneous 2-ton lashing capability ----Chassis: * Chassis made of high-strength fine-grain steel ----Load Securing (Lasi - Package): Turntable Platform: * 2 pairs of 13.4-ton lashing eyes in the outer frame of the turntable platform Low-bed: * 4 pairs of 10-ton lashing eyes on each side of the outer frame, retractable and loadable in all directions * 2 pairs of 13.4-ton swiveling lashing eyes on each side at the rear ----Ramps: * Rubber coating on the folding access ramps * Hydraulic folding ramps with hydraulic extendable front section, approx. 4,650 x 720 mm * Hydraulic lateral ramp adjustment & load holding valves ----Rear Support: * Hydraulic rear support ----Width Extension: * 8 pairs of galvanized folding outriggers for 3 m overall width (however, not in the rear slope) * Width extension boards stored in a compartment on the left side ----Excavator Arm Rest: * Excavator arm rest above the rear axle to the end of the access ramp, approx. L=2,100 mm x W=740 x D=190 mm * 2 pairs of 6.4-ton lashing eyes on the side in the excavator arm rest ----Hydraulics: * Hydraulic flow divider in the trailer (with hydraulic pump output in the truck of over 40 - max. 120 l/min.) ----Loading Dimensions: * Rear loading area: approx. 6,780 x 2,520 mm (incl. 860 mm access ramp) * Loading area above the turntable: approx. 2,990 x 2,520 mm ----Loading Height: * approx. 890 mm, +/- 20 mm ----Painting: * Reflective contour striping on the sides and at the rear * Chassis, turntable, access ramps, and folding outriggers hot-dip galvanized * Axles, drawbar, air tanks, and turntable painted in a black color ----Information: * New vehicle with manufacturer's warranty * Subject to errors and prior sale ----Delivery Time: * Immediately available from Egestorf

Condition: new, maximum load weight: 38,290 kg, overall weight: 48,000 kg, axle configuration: 3 axles, loading space length: 8,500 mm, loading space width: 2,520 mm, Year of construction: 2026, * TS 3 Profile 30.0: ----Brakes: * Wabco EBS-E (electronic braking system) * Emergency release device for spring-loaded cylinders * Drum brakes ----Axles: * 3 x 11 t BPW Eco Plus axles * Last axle steered, with electro-pneumatic steering lock ----Suspension: * Air suspension with lift and lower system and RtR valve ----Electrics / Lighting: * TPMS (Tire Pressure Monitoring System) * Smartboard control box mounted on the trailer as an info tool, with pressure sensors for total axle load display * 15-pin electrical connector * LED lighting system 12 / 24V Ndsdpfxoy Ngz Hj Agxea * Removable LED beacon, left rear ----General attachments: * Side underrun protection * Landing legs at the front and mechanical swivel supports at the rear of the chassis * Straight steel mudguards * Spare wheel carrier under the chassis, right side ----Low-loader deck: * Saddle platform with 45° chamfered front corners and a front toolbox made of galvanized sheet steel, W = 2,480 x H = 500 x L = 665 mm, with folding lid * 400 mm high drop-side aluminum boards (RAL 9010 pure white), foldable and removable, on the sides of the saddle platform * Rear board – 150 mm high, slotted in * Rear slope on the saddle platform to the low-bed section, approx. 700 mm long * Saddle platform with 50 mm wooden planks and low bed with 60 mm wooden planks * Tread plate over the axles ----Widening: * 8 x mechanical folding extensions to 3 meters total width, not on the rear slope (widening planks available, stored on the saddle platform) * Mechanically adjustable warning panel sets front and rear ----Load securing (Lasi package): * On the saddle platform, 2 x 6.3 t lashing points each, as well as 3 x 5 t lashing bars each on the outside frame * On the low-bed platform, 2 x 13.4 t lashing rings on each side, as well as 4 x 10 t lashing rings, pivotable and lowerable, integrated into the outside frame * On each side, 2 x 6.4 t lashing eyes and one lashing point in the excavator arm trough at the rear * 2 x container locks directly after the gooseneck in the low bed platform ----Excavator arm trough: * Excavator arm trough starting from the end of the last fixed axle, over the steering axle up to the rear cross member, continuous with internal reinforcement profiles, approx. L = 2,450 x W = 770 mm x D = 270 mm ----Ramps: * Mechanically operated one-piece, hot-dip galvanized hydraulic ramps, approx. 3,000 x 720 mm (mechanically adjustable in width) * 4-way control block for later customer-side retrofit of hydraulic ramp shifting * The outer board of the ramp is made of 50 mm hardwood * Climbing strips on the outer frame of the ramp and on the approach slope * Rubber mat on the ramp and approach slope ----Hydraulics: * Hydraulic flow divider in the trailer (for hydraulic pump output in truck over 40 l up to 120 l/min) ----Load dimensions: * Loading area of the saddle platform: approx. 3,935 x 2,480 mm * Low-bed loading area: approx. 8,500 x 2,520 mm * Loading height unladen about 910 mm (incl. 860 mm approach slope) ----Fifth wheel height: * Approx. 1,220 mm (suitable for 2- and 3-axle tractors) ----Paintwork: * Chassis, ramps, rear folding supports, widening consoles hot-dip galvanized * Axles, landing legs, air tanks painted black * Vehicle is hot-dip galvanized ----Info: * New vehicle with manufacturer's warranty * Errors and prior sale excepted * Example images may show equipment not included with the offered vehicle * Sample images ----Delivery time: * tba

Condition: new, maximum load weight: 10,660 kg, overall weight: 14,400 kg, axle configuration: 2 axles, loading space length: 5,000 mm, loading space width: 2,420 mm, loading space height: 600 mm, Year of construction: 2026, * KA-TA-R 14.4: ----Brakes: * Wabco EBS (electronic braking system) * Emergency release device for spring brake cylinders * Drum brakes ----Axles: * 2 x 7-ton Gigant axles ----Suspension: * Parabolic springs with tandem equalizer ----Drawbar / Flange coupling: * Height-adjustable drawbar by 300 mm with 40 mm flange coupling ----Electrical system / Lighting: * 15-pin power connector * LED rear lights 12/24 V * Tire pressure monitoring with display option in the truck via EBS signal - without truck-side installation Ndodpfx Aex Hm Rcogxsa ----General components: * Jost mechanical support legs at the front * 2 mechanical folding support legs at the rear * Plastic tool box approx. 750 x 350 x 300 mm at the front on the right side of the chassis * Underride guard, bolted * Plastic quarter fenders ----Tipping bridge: * Net hooks in the bearings of the central locking system, as well as 2 on the front wall * Steel pallet-type 3-way tipping body with adjustable Strong sideboards (continuous side walls with internal tube reinforcement at the top - without center posts - can be folded down with sideboard spring lifters) * Rear crossbars, bolted * Combination steel hinged doors - rear wall 2-wing asymmetrical - can be pivoted and locked 270° - not foldable - as well as with additional swivel frames for the automatic rear wall opening during tipping, locking via galvanized swivel rod latch at the rear and central locking, deactivation function for automatic rear wall function when tipping backwards with the hinged door open * 4 mm sheet steel floor made of fine-grain steel ----Load securing: * 1 x 5-ton lashing point in each corner * 4 x 3-ton lashing points on each side, embedded in the outer frame ----Chassis: * Chassis made of fine-grain steel ----Ramps: * Mounting rail at the rear for the loading ramps * 1 pair of aluminum loading ramps approx. 3,570 x 410 mm (load capacity 10 tons / pair) suitable for rubber-tired and tracked vehicles * Storage compartment lockable from the rear, located below the loading area in the chassis for the ramps ----Tires: * Tires 358/55 R 19.5 ----Painting: * Drawbar, underride guard, rear crossbars, folding support legs at the rear hot-dip galvanized * Axles, springs, air tanks, and support legs painted in a black tone * Painting of the sideboards in a RAL color of your choice (however, no special or metallic paint) can be changed up to approx. 6 weeks before completion ----Information: * Body - reinforced - with load securing certificate * Errors and prior sale excepted * Sample images ----Delivery time: * Available immediately from week 29/2026

Condition: new, maximum load weight: 10,660 kg, overall weight: 14,400 kg, axle configuration: 2 axles, loading space length: 5,000 mm, loading space width: 2,420 mm, loading space height: 600 mm, Year of construction: 2026, * KA-TA-R 14.4: ----Brakes: * Wabco EBS (electronic braking system) * Emergency release system for spring brake cylinders * Drum brakes ----Axles: * 2 x 7-ton Gigant axles ----Suspension: * Parabolic springs with tandem equalizer ----Drawbar / Flange coupling: * Height-adjustable drawbar by 300 mm with 40 mm flange coupling ----Electrical system / Lighting: * 15-pin power socket * LED tail lights 12/24 V * Tire pressure monitoring system with display option in the truck via EBS signal - without truck-side installation ----General components: * Jost mechanical support legs (front) * 2 mechanical folding support legs (rear) * Plastic toolbox approx. 750 x 350 x 300 mm on the front side, right on the chassis * Underrun protection, bolted * Plastic quarter fenders ----Tipping bridge: * Net hooks in the bearings of the central locking system, as well as 2 on the front wall * Steel pallet-sided, 3-way tipping body with adjustable strong side boards (continuous side walls at the top with internal tube reinforcement - without center posts - foldable with side board spring lifters) * Rear supports, bolted * Combination steel wing doors - rear wall, 2-wing, asymmetrically divided - swivels and locks at 270° - not foldable - as well as with additional pivot frames for the automatic rear wall opening during tipping, locking via a galvanized swivel rod lock at the rear and central locking, deactivation function for the automatic rear wall function when tipping backwards with the wing door open * 4 mm sheet metal floor made of fine-grained steel ----Load securing: * 1 x 5-ton lashing point in each corner * 4 x 3-ton lashing eyes on each side, embedded in the outer frame ----Chassis: * Chassis made of fine-grained steel ----Ramps: * Receiving rail at the rear for the loading ramps * 1 pair of aluminum loading ramps approx. 3,570 x 410 mm (load capacity 10 tons / pair) suitable for rubber-tired and tracked vehicles * Storage compartment under the loading area in the chassis for the ramps, lockable from the rear ----Tires: * Tires 358/55 R 19.5 ----Painting: * Drawbar, underrun protection, rear supports, folding support legs (rear) hot-dip galvanized * Axles, springs, air tanks and support legs painted in a black tone * Painting of the side boards in a RAL color of your choice (but no special or metallic paint) can be changed up to approx. 6 weeks before completion ----Information: * Body - reinforced - with load securing certificate * Errors and prior sale reserved * Sample images ----Delivery time: Nedpfxsx Hm Ris Agxoda * Available for immediate delivery from week 29/2026

Condition: new, maximum load weight: 8,410 kg, overall weight: 11,900 kg, axle configuration: 2 axles, loading space length: 5,000 mm, loading space width: 2,420 mm, loading space height: 600 mm, Year of construction: 2025, * KA - TA - R 11.9 ----Braking System: Ndsdpfx Aexf Skvegxja * Wabco EBS (electronic braking system) * Emergency release device for spring brake cylinders * Drum brakes ----Axles: * 2 x 5.5 t BPW axles ----Suspension: * Parabolic springs with tandem equalization unit ----Drawbar / Flange Eye: * Height-adjustable drawbar (300 mm range) with 40 mm flange towing eye ----Electrics / Lighting: * Tire pressure monitoring with in-cab display via EBS signal – no installation required on the truck side * 15-pin power connector * LED lighting system, 12/24 V * 2 LED reversing lights at the rear (activated via reverse gear) ----General Attachments: * Mechanical BPW landing gear at the front * 2 mechanical folding supports at the rear * Plastic toolbox, approx. 750 x 350 x 300 mm, mounted on the right side of the chassis at the front * Bolt-on underrun protection * Plastic quarter mudguards * Two-step access in front of the bulkhead, driver’s side ----Chassis: * Chassis made of fine-grain steel ----Tipping Body: * Net hooks at each central locking bearing and two on the bulkhead * Steel palletised 3-way tipper body with reinforced 600 mm heavy-duty drop sides * Continuous top side walls with internal tube reinforcement – no central stanchions – foldable with drop side spring assist * Rear stanchions bolted * Combination steel double-wing rear doors, asymmetrically split, swivel 270° and lockable (not foldable) with additional swing frame for automatic tailgate opening during tipping * Locking via galvanized rotary bar lock at the rear and central locking * Deactivation function for automatic tailgate during reverse tipping with opened wing doors * Mounting rail at the rear for loading ramps ----Load Securing: * 1 x 5 t lashing point in each corner and 4 x 3 t lashing eyes recessed in the side outer frame * 4 mm floor plate made of S 420 MC 4 fine-grain steel ----Ramps: * 1 pair of aluminum loading ramps (approx. 3,310 x 400 x 105 mm, load capacity 8 t/pair), suitable for rubber-tired and tracked vehicles * Lockable storage compartment under the loading area at the rear of the chassis ----Paintwork: * Chassis, drawbar, tipper body, bulkhead, underrun protection, rear stanchions, rear folding supports, and access step galvanized * Side walls and tailgate painted in RAL 3003 ruby red * Axles, springs, air tanks, and landing gear painted in a shade of black ----Information: * Reinforced body with load securing certificate according to EN 12642 XL * New vehicle with manufacturer’s warranty * Subject to errors and prior sale ----Delivery time: * Available immediately ex works Egestorf

Condition: new, maximum load weight: 10,800 kg, overall weight: 14,400 kg, axle configuration: 2 axles, loading space length: 6,270 mm, loading space width: 2,470 mm, Year of construction: 2026, * ETÜ-TA-R 14.4: ----Brakes: * EBS brake system * Emergency release device for spring-loaded cylinders * Drum brakes ----Axles: * 2 x 7 t Gigant axles ----Suspension: * Parabolic leaf springs with equalising unit ----Drawbar / Flange Tow Eye: * Height-adjustable drawbar, adjustable by 300 mm * Drawbar extension by 250 mm to a total length of 2,250 mm ----Electrics / Lighting: * Tyre pressure monitoring with display option in the truck via EBS signal - no installation required on the truck side * 15-pin power connector * LED lighting system 12 / 24 V * EBS multi-voltage system for towing vehicles with 12 and 24 V electrics ----General Attachments: * Support winch at the front * Rear external folding supports * Plastic toolbox approx. 858 x 500 x 500 mm mounted front right on the bulkhead exterior * Side underrun protection * Plastic quarter mudguards ----Low Loader Deck: * 50 mm softwood flooring * Preparation in front of the bulkhead for subsequent fitting of container locks * Bolted, 400 mm smooth-sheet bulkhead * Bolted rear stanchions * Side panels with spring assist ----Load Securing: * Perforated outer frame, bent approx. 45 degrees, with 2 t lashing capacity every 480 mm * Option to install 3 t folding lashing rings every 600 mm * 1 x 6.3 t lashing point each in the front and rear corners * Various drilled holes in the front and rear cross members for 1.2 t lashing options * Profifix lashing rail centrally in the longitudinal axis for lashing up to LC 3000 daN ----Ramps: * One-piece hydraulic mesh loading ramps approx. 2,750 x 600 mm (can be pushed together up to 20 mm) * Hydraulic flow divider in the trailer (for hydraulic pump output in the truck over 40 ltr./min. up to 140 ltr./min. max) ----Paintwork: Ndjdpfx Ajrwc R Aogxea * Chassis, drawbar, bulkhead, mechanical drop legs, and loading ramps hot-dip galvanised * Axles, springs, air tanks, front support winch, and flange tow eye painted in a black tone * Side panels painted in RAL 9010 pure white * Painting of side walls in any RAL colour available at extra cost ----Info: * New vehicle with manufacturer’s warranty * Errors and prior sale reserved * Sample images ----Delivery time: * Available immediately ex Egestorf

Condition: new, maximum load weight: 8,850 kg, overall weight: 11,900 kg, axle configuration: 2 axles, loading space length: 5,000 mm, loading space width: 2,420 mm, loading space height: 500 mm, Year of construction: 2024, * KA-TA-R 11.9 "Masterline" ----Brakes: * EBS brake system * Emergency release device for spring brake cylinders * Drum brakes ----Axles: * 2 x 5.5 ton BPW axles ----Suspension: * Parabolic springs with tandem equalizer unit ----Drawbar / Flange Eye: * Drawbar height-adjustable by approx. 300 mm with 40 mm flanged towing eye ----General Attachments: * Jost mechanical support winch at front * Two mechanical, hot-dip galvanized folding support legs at rear * Plastic toolbox approx. 750 x 350 x 300 mm, mounted on the right side * Bolted underride guard * Plastic quarter fenders ----Electrics / Lighting: * 15-pin power connector * LED lighting * TPMS (Tire Pressure Monitoring System) Nodpfxsl Thyms Agxjda ----Tipper Bed: * Net hooks on the sides and rear, fitted to the central locking bearings, plus 2 on the front bulkhead * Steel pallet 3-way tipper body (continuous sidewalls - without center stanchions - foldable with drop-side spring assist) * Rear stanchions bolted * Steel combination swing doors at the rear, asymmetrically split, 2-leaf, can be swung and locked to 270°, not foldable – also equipped with additional swinging frame for automatic tailgate opening during tipping. Locking via galvanized rotary bar lock and central locking system * Deactivation function for automatic tailgate during rear tipping with open swing door * 4 mm steel floor plate * Mounting rails at the rear for loading ramps ----Load Securing: * One 5 ton lashing point in each corner * Four 3 ton lashing rings recessed into the outer frame on each side ----Ramps: * One pair of aluminum loading ramps, approx. 3,310 x 400 mm (load capacity 8 tons/pair), suitable for rubber-tired & tracked vehicles * Lockable storage compartment under the load area, inset into the chassis, accessible from the rear ----Paintwork: * Drawbar, front wall, tipper bed, rear stanchions, underride guard, mechanical support legs hot-dip galvanized * Sidewalls and tailgate painted RAL 9010 pure white * Other RAL shades for sidewalls available at extra cost * Axles, springs, towing eye, air tanks, and support winch painted black ----Other Information: * Reinforced body with load securing certificate according to EN 12642 XL * New vehicle without initial registration, with manufacturer's warranty * Subject to prior sale and errors ----Delivery Time: * Immediately available from Egestorf on the A7

Condition: new, maximum load weight: 6,870 kg, overall weight: 9,900 kg, axle configuration: 1 axle, Year of construction: 2026, * KWH 9.9 ML: ----Brakes: * EBS braking system * Drum brake * Emergency release device for spring accumulators ----Axle: * BPW axle ----Suspension: * Parabolic springs ----Drawbar / Flange coupling: Ndsdpfou I Iqrex Agxoa * Drawbar with 40 mm threaded coupling (height-adjustable, in mm) ----Electrical System / Lighting: * 15-pin power connector * LED lighting * Flashing LED side marker lights * TPMS (Tire Pressure Monitoring System) ----General Components: * Front support jack * Spring-assisted square tube supports at the rear with base plate, safety locking pins for various support heights * Closed steel sheet fenders with splash guard * Closed side underrun protection, usable as an advertising space * Plastic toolbox with base insert (horizontal installation), approx. 500 x 350 x 400 mm ----Superstructure: * Swivelable cable drum superstructure, width between the drum arms 1,700 mm with locking mechanism to secure the drum at the ends of the support arms, as well as a locking mechanism for the cable drum superstructure with the chassis by means of a centrally arranged claw lock * Motor-hydraulic drum drive with oil motor * Valves and adjustable, rubber-coated drive rollers * Hydraulic speed controller and brake for drum drive * Steel drum shaft with 76 mm diameter, centering and rotatable ends * 1 pair of centering cones made of polyamide, stepped ----Chassis: * Chassis made of torsion-resistant square tubes and cross members ----Pump Unit: * Hydraulic pump unit with Loncin gasoline engine, including manual and electric starter * Fuel tank and manual starter * 13 HP with gear pump (150 bar) ----Tires: * 315/80 R 22.5 ----Unladen Weight: * 2,690 kg unladen weight ----Paint Finish: * Vehicle is hot-dip galvanized ----Information: * New vehicle with full manufacturer's warranty * Errors and prior sale excepted ----Delivery Time: * Available from approximately week 41/2026

Condition: new, maximum load weight: 37,560 kg, overall weight: 48,000 kg, axle configuration: 3 axles, Year of construction: 2026, * TS 3 RM ML 30.0: ----Brakes: * Wabco EBS-E (electronic braking system) * Emergency release device for spring brake cylinders * Drum brakes ----Axles: * 3 x 11 t BPW axles * Start assist for maneuvering purposes on the first axle, activated via EBS (no truck-side installation required) * Last axle is a trailing steering axle with electro-pneumatic steering lock * Lock for the trailing axle, actuated from the driver's cab for maneuvering purposes via EBS (no truck-side installation required) ----Suspension: Ndjdpfx Agjykx Nqsxoa * Air suspension with raise/lower system and RtR valve ----Electrical / Lighting: * Smart-Board installed as an information tool on the trailer, with pressure sensors for total axle load display * 15-pin power connector * LED lighting 12/24 V * Removable rear LED beacon * 2 additional LED reverse lights * 7-pin socket at rear for overlength lighting * Side marker lights with indicator actuation * Tire pressure monitoring with display option in the truck via EBS signal (no truck-side installation required) ----General Attachments: * Side underrun protection * Landing gears at the front and swing-out supports at the rear * Straight steel fenders * Spare wheel carrier in front of the bulkhead crossmember (without spare wheel) * Mechanically adjustable warning panel sets at front and rear * Pivoting arm as a carrier for connection lines from the truck to the trailer ----Low Loader Bed: * Second kingpin position * Fifth-wheel platform with 45° chamfered front corners and front toolbox made of galvanized, powder-coated steel plate (W = 2,480 mm x H = 500 mm x L = 665 mm) with hinged lid * 400 mm high aluminum sideboards (RAL color of choice), foldable and removable on the fifth-wheel platform * 150 mm high plug-in rear wall * Rear slope on the fifth-wheel platform towards the low-bed, approx. 700 mm long with tread plate covering and a perforated bar at the end for hooking on aluminum ramps * Fifth-wheel platform with 50 mm clamped timber planks, and low-loader deck with 60 mm clamped timber planks * Tear plate over the axles * 9 mechanical swing-out extensions for total width of 3 m (not on rear slope), extension boards available with a transverse storage compartment under the loading area * Prepared for 3 insertion shafts under the fifth-wheel platform for storing either aluminum ramps or timber planks for wheel recess covers * Preparation for container locks on the swan neck ----Load Securing (LaSi Package): Fifth-wheel Platform: * Perforated outer frame, bent at 45°, with hole pattern for lashing equipment (2 t lashing force per lashing point at a minimum spacing of 480 mm) * On each side, 3 x 13.4 t recessed lashing rings in the floor (1 on the fifth-wheel platform, 1 on the longitudinal member after the neck step, 1 above the middle axle next to the longitudinal member) Low Loader Platform: * On each side, 3 x 13.4 t lashing rings on the outer frame (1 at the neck step of the fifth-wheel platform, 1 at the start of the ramp, 1 at the end of the ramp) * On each side, 2 x 10 t lashing rings (1 between the front wheel recess and the first axle, 1 between the 2nd and 3rd axle) * On each side, 3 x 5 t lashing rings bolted to the outer frame of the wheel recesses (2 at the front, 1 at the rear wheel recess) ----Excavator Arm Rest: * Extended excavator arm rest from the end of the last fixed axle over the steering axle up to the rear crossmember, continuous with internal reinforcement profile, approx. 770 mm wide x T at t

Condition: new, maximum load weight: 17,650 kg, overall weight: 24,000 kg, axle configuration: 3 axles, loading space length: 9,230 mm, loading space width: 2,480 mm, Year of construction: 2026, * TP 30.0 with 3 cable drum supports ----Braking system: * Wabco TEBS (electronic braking system) * Emergency release device for spring brake cylinders * Drum brakes ----Axles: * 3 x 11 t Gigant axles ----Suspension: * 17.5" air suspension with lifting and lowering facility ----Drawbar: * Drawbar 1,800 mm long with 40 mm towing eye ----Electrics / Lighting: * Tyre pressure monitoring with display option in the truck dashboard via EBS signal (no truck-side installation required) * 15-pin power connector * 2 additional LED reversing lights (switched via reverse gear) Ndedpfx Aex Nlkaogxoa * LED lighting ----General attachments: * Aluminium air tank * Stainless steel side toolbox approx. 1,000 x 300 x 600 mm * Side underrun protection * Plastic quarter mudguards * Rear underrun protection ----Platform: * Zurr-fix external frame, 45° angled, perforated for lashing devices, lashing capacity per lashing point 2,000 kg at a distance of 480 mm * Installation of 3,000 kg folding lashing rings at approx. 600 mm spacing possible - each side comes with 12 x 3,000 kg lashing rings supplied * Each side features 5 pockets for pipe stanchions 100 x 50 mm in the outer frame (pipe stanchions not included) * 30 mm phenolic resin-coated plywood floor ----Cable drum supports: * 3 galvanized cable drum supports, secured via container locks with side forklift pockets centre-to-centre 800 mm (pocket width 185 mm) * Max. drum diameter 2,600 mm and max. drum width 1,650 mm * Clear width between support arms approx. 1,775 mm, with cross-brace * Max. drum weight per support: 6,000 kg * Without drive or drum brake * Support arm with clamping lock for securing the drum shaft * Steel drum shaft, 76 mm diameter, with centering and rotating ends * 2 retaining collars * 2 centring cones made of polyamide * 4 x 3.2 t lashing eyes on the support arms to secure the drum against unintentional rotation and unwinding (provided by customer) ----Loading height: * approx. 1,040 mm loaded ----Paintwork/finish: * Chassis, turntable, drawbar, outer frame, and underrun protection hot-dip galvanized * Axles painted in black

Condition: new, maximum load weight: 10,500 kg, overall weight: 14,400 kg, axle configuration: 2 axles, loading space length: 6,270 mm, loading space width: 2,470 mm, loading space height: 400 mm, Year of construction: 2026, * ETÜ - TA -R 14.4 ----Braking system: * EBS braking system * Emergency release device for spring-loaded cylinders * Drum brakes ----Axles: * 2 x 7 t Gigant axles ----Suspension: * Parabolic springs with compensation unit ----Drawbar / Flange Eye: * Height-adjustable drawbar by 300 mm – drawbar extension by 250 mm to 2,250 mm * 40 mm flange towing eye ----Electrics / Lighting: * Tire pressure monitoring with display capability in the truck via EBS signal (no in-truck installation required) * 15-pin power connector * LED rear lights 12/24 V * Removable LED beacon at the rear ----General Accessories: * Support winch at the front * Externally mounted hot-dip galvanized folding supports at the rear * Plastic toolbox approx. 858 x 500 x 500 mm, front right outside on the front wall * Side underrun protection * Plastic quarter mudguards ----Lowbed Area: Ndsdpfx Aox Ipapjgxja * Provision in front of the front wall for retrofitting container locks * Bolted front wall made of smooth sheet metal * Side walls made of profiled steel sheet, foldable with side wall spring lifters * Steel rear wall insertable between the ramps – storage bracket inside at the front wall when not in use * Removable bolted rear stanchions * Inclined access ramp at rear, approx. 860 mm ----Floor Covering: * 50 mm softwood floor * 12 mm thick and 270 mm wide rubber strips on the inside of the loading ramps * 12 mm thick and 210 mm wide rubber strips on the access slope and externally on the lowbed platform (from front to rear cross member) ----Load Securing: * Perforated outer frame, approx. 45° angled, with 2 t lashing capacity every 480 mm * Installation option for 3 t folding lashing rings every 600 mm * Each front and rear corner with 1 x 6.3 t lashing ring * Multiple holes in front and rear cross member for 1.2 t lashing options ----Ramps: * One-piece mechanical grating ramps with spring mechanism for one-person operation, approx. 2,750 x 870 mm (retractable to 20 mm) ----Paintwork: * Chassis, drawbar, front wall, tailgate and ramps hot-dip galvanized * Axles, springs, air tanks and flange towing eye painted in black * Side walls painted in RAL 9010 pure white ----Information: * --Reinforced and certified body according to EN 12642 XL including load securing certificate-- * Subject to errors and prior sale * New vehicle with manufacturer's warranty ----Delivery time: Vehicle is immediately available

Condition: new, maximum load weight: 38,290 kg, overall weight: 48,000 kg, axle configuration: 3 axles, loading space length: 8,500 mm, loading space width: 2,520 mm, Year of construction: 2026, * TS 3 Profile 30.0: ----Brakes: * Wabco EBS-E (electronic braking system) * Emergency release device for spring-loaded cylinders Njdspk D I Ajpfx Agxoda * Drum brakes ----Axles: * 3 x 11 ton BPW Eco Plus axles * Rear axle is self-steering with electro-pneumatic steering lock ----Suspension: * Air suspension with lift/lower mechanism and RtR valve ----Electrics / Lighting: * TPMS (Tire Pressure Monitoring System) * Smartboard control unit mounted on the trailer as an info tool with pressure sensors for total axle load display * 15-pin power connector * LED lighting system 12/24V * Removable LED beacon, mounted at rear left ----General attachments/accessories: * Side underrun protection * Landing gears at the front and mechanical swing-down supports at the rear of the chassis * Straight steel mudguards * Spare wheel holder underneath the chassis, on the right side ----Low Loader Deck: * Saddle platform with front corners chamfered at 45°, and a front-mounted toolbox made of galvanized steel (W = 2,480 x H = 500 x L = 665 mm) with hinged lid * 400 mm high, foldable and removable aluminum side boards (RAL 9010 pure white) mounted on the saddle platform * 150 mm high rear board, slotted in * Rear slope on the saddle platform leading to the lowbed, approx. 700 mm long * Saddle platform fitted with 50 mm wooden planks; lowbed platform with 60 mm wooden planks * Tread plate over the axles ----Widenings: * 8 mechanical fold-out extensions to 3 m total width (except on the rear slope; extension planks included with storage on the saddle platform) * Mechanically adjustable warning panel sets at front and rear ----Load Securing (Lashing Package): * On the saddle platform: 2 x 6.3 t lashing rings on each side, 3 x 5 t lashing rods on each side in the outer frame * On the lowbed platform (sides): 2 x 13.4 t lashing rings on each side plus 4 x 10 t lashing rings, swiveling and retractable, recessed into the outer frame * On the sides: 2 x 6.4 t lashing eyes each, plus 1 lashing ring at the rear in the excavator arm support * 2 x container locks directly after the gooseneck in the lowbed platform ----Excavator Arm Support: * Continuous excavator arm tray from the end of the last fixed axle, over the steering axle, up to the end cross member, with internal reinforcement profiles, approx. L = 2,450 x W = 770 mm x D = 270 mm ----Loading Ramps: * Mechanically operated, one-piece, hot-dip galvanized hydraulic loading ramps, approx. 3,000 x 720 mm (mechanically adjustable sideways) * 4-way valve block for future customer retrofitting of hydraulic ramp shifting * Outer plank on the ramp made of 50 mm hardwood * Climbing strips on the outer frame of the ramp and on the approach slope ----Hydraulics: * Hydraulic flow divider in the trailer (for hydraulic pump capacities on truck from 40 l/min up to 120 l/min) ----Loading dimensions: * Saddle platform loading area: approx. 3,935 x 2,480 mm * Lowbed loading area: approx. 8,500 x 2,520 mm * Unladen load height approx. 910 mm (incl. 860 mm approach slope) ----Fifth wheel height: * Approx. 1,220 mm (suitable for 2- and 3-axle tractor units) ----Paint/Finish: * Chassis, loading ramps, rear support legs, and extension consoles hot-dip galvanized * Axles, landing gears, air tanks painted in a shade of black * Vehicle is hot-dip galvanized ----Info: * New vehicle with manufacturer's warranty * Subject to errors and prior sale * Sample images may show equipment features not included with the offered vehicle ----A

Condition: new, maximum load weight: 27,940 kg, overall weight: 36,000 kg, axle configuration: 3 axles, Year of construction: 2026, * Wabco EBS-E (electronic braking system) * Emergency release device for spring brake cylinders Ndjdpewh Hdxefx Agxea * Drum brakes * 3 x 11 t axles * Air suspension with lift and lower function as well as RtR valve * Traction assistance for shunting, activated on the first axle via EBS – without truck-side installation – with lifted lift axle + 30 mm driving height * Smart-Board infotool mounted on the trailer, equipped with pressure sensors for total axle load display * Last axle as a trailing steering axle with electro-pneumatic steering lock * Locking of the trailing axle activated from the cab for maneuvering purposes via EBS (without truck-side installation) * 2" king pin * 1 liftable axle * Side underrun protection * Front aluminum drop-down supports and rear swivel supports on the chassis * Alcoa LVL One aluminum rims * 15-pin power connector * LED lighting 12 / 24 V * Rear removable LED rotating beacon * 2 additional LED reversing lights * 2 LED work lights mounted laterally on the trailer (without truck-side installation) * 7-pin socket at the rear for oversize load lighting * Side marker lights with indicator control * Tire pressure monitoring system with display capability in the truck via EBS signal (without truck-side installation) * Mechanically adjustable warning sign packages front and rear * Straight steel mudguards * Semi-trailer platform with 45° chamfered front corners and a front toolbox made of galvanized, powder-coated steel sheet (W = 2,480 x H = 500 x L = 665 mm) with top hinged lid and side doors in the chamfered corners * 400 mm high aluminum side walls (RAL 9010 pure white) on the sides of the semi-trailer platform, foldable and removable * Rear panel inserted, height 150 mm * Rear slope on the semi-trailer platform to the low bed, approx. 700 mm long with anti-slip tread plate surface and a perforated strip at the end for hanging on aluminum loading ramps * Semi-trailer platform and low loader platform with 50 mm clamped timber floorboards * Checker plate above the axles * Prepared for 3 slots underneath the semi-trailer platform for storage of optional aluminum loading ramps * Swivel arm as support for connection lines from the truck to the trailer * Load securing package (LaSi): perforated outer frame on the semi-trailer platform with 45° edge and hole pattern for lashing equipment (2 t lashing capacity per point at minimum spacing of 480 mm), each side with 2 x 6.3 t recessed lashing rings in the floor, each side with 1 x 16.5 t lashing ring in the incline from the low loader platform to the semi-trailer platform, 2 pairs of 16.5 t lashing rings in the low loader platform (1 x on the longitudinal beams after the step, 1 x above the center axle beside the longitudinal beam), each side with 3 x 13.4 t lashing rings on the outer frame (1 x at start of the semi-trailer step, 1 x at start of loading ramp slope, 1 x at end of loading ramp slope), each side with 3 x 10 t lashing rings (2 x between front wheel recess and first axle, 1 x between second and third axle), each side with 3 x 5 t lashing rings bolted to the outer frame of the wheel recesses (2 x at front, 1 x at rear wheel recess) * Extended excavator arm trough running from the end of the last fixed axle over the steering axle up to the rear crossmember, with internal reinforcement profile, approx. W = 770 mm x rear D = 270/front D = 170 mm, each side with 2 x 6.4 t lashing rings in the excavator arm trough * Each side with 2 wheel recesses, 390 mm deep and 640 mm wide, f

Condition: new, maximum load weight: 20,500 kg, overall weight: 27,000 kg, axle configuration: 3 axles, loading space length: 7,000 mm, loading space width: 2,470 mm, Year of construction: 2026, * ETÜ-TR 27.0 Platform: * EBS (electronic braking system) * Emergency release device for spring-loaded brake cylinders * Drum brakes * 3 x 9 t BPW Eco axles * Air suspension with lift and lower function including RTR feature * 1st axle liftable * Last axle as trailing steering axle with electro-pneumatic steering lock activated via reverse gear PIN (lockout of the trailing axle from driver's cab for maneuvering - no truck-side installation required - assigned to PIN 10 of the 15-pin connector; for maneuvering purposes only, not for public road use) Nedpfx Aor Dpz Asgxjda * SmartBoard control box as infotool with pressure sensors for total axle load display * Tire pressure monitoring with display option in the truck via EBS signal (no truck-side installation required) * Fixed center drawbar with 50 mm flanged towing eye (900 mm when loaded, height adjustable at the head plate) * Mechanical support winch in front, mechanical swing-down supports at the rear of chassis * Mechanically adjustable warning sign package front and rear * Toolbox made of galvanized steel sheet - black powder coated - approx. 650 x 300 x 600 mm, mounted on the right side * Hydraulic flow divider * Continuous sidewalls (without center stanchion) up to the approach ramp * Folding rear stanchions * Steel rear wall inserted in front of rear stanchions * 15-pin power connector * LED taillights * LED revolving beacon (removable), incl. bracket and installation * 2 x LED reversing lights at the rear of vehicle (activated by reverse gear) * Flashing LED side marker lights * 60 mm larch/douglas fir flooring * 400 mm plug-in steel front wall * Perforated outer frame, approx. 45° chamfered with provisions for mounting 3 t folding lashing brackets * 1 x 10 t lashing ring in each corner; additionally, 2 x 10 t and 3 x 6.3 t lashing rings on each side * Various holes in front and rear cross-members for 1.2 t lashing options * Hydraulic one-piece loading ramps approx. 3,000 x 720 mm, mechanically adjustable sideways * 4-way hydraulic control block for optional retrofitting of hydraulic ramp displacement * Chassis, drawbar, front wall, mechanical rear supports, loading ramps, and tailgate fully hot-dip galvanized * Axles, air tanks, flanged towing eye, and front support winch painted in black * Hydraulic flow divider in trailer (for hydraulic pump capacity in truck from over 40 l/min up to 120 l/min) * New vehicle with manufacturer’s warranty * Errors and interim sales excepted * Immediately available ex Egestorf

Condition: new, maximum load weight: 6,810 kg, overall weight: 9,600 kg, axle configuration: 1 axle, loading space length: 4,030 mm, loading space width: 2,420 mm, loading space height: 700 mm, Year of construction: 2026, * EK 9.6 ----Brakes: * EBS (Electronic Braking System) * Emergency release device for spring brake cylinders * Drum brakes ----Axle: * SAF axle ----Suspension: * Parabolic springs ----Drawbar / Flange Drawbar Eye: * Drawbar as central pole with 40 mm bolted drawbar eye * Stepless drawbar height adjustment with spindle lifting mechanism instead of rigid drawbar ----Coupling height: * Standard coupling height approx. 900 mm (+/- 150 mm) ----Electrics / Lighting: * Tire pressure monitoring with display capability in the truck via EBS signal (no installation required on the truck side) * 15-pin power plug * LED tail lights * Flashing side marker lights ----General Attachments: * Support winch at the front * Enclosed plastic mudguards * Folding underrun guard for pavers ----Chassis: * Chassis made of fine-grained steel ----Tipping body: * 3-way tipping body for pallets * 700 mm steel front wall * Aluminum side walls, asymmetrical – continuous, without center stanchion – foldable with long-stroke locks and pendulum action via manual central locking * Steel rear wall 800 mm high with automatic rear wall opening during rear tipping * 4 mm Hardox 450 steel floor ----Load securing: Ndodpfx Aew Ndr Uogxoa * 2 pairs of 3-ton lashing rings recessed and foldable in the steel floor on each side ----Paintwork: * Chassis, drawbar, underrun guard hot-dip galvanized * Tipping body painted in a RAL color of your choice (no special or metallic paints); can be changed up to approx. 6 weeks before completion ----Information: * New vehicle with manufacturer’s warranty * Errors and prior sale excepted ----Delivery time: * Available from approx. week 42/2026

Condition: new, maximum load weight: 17,650 kg, overall weight: 24,000 kg, axle configuration: 3 axles, loading space length: 9,230 mm, loading space width: 2,480 mm, Year of construction: 2026, * TP 30.0 with 3 cable drum supports ----Braking System: * Wabco TEBS (electronic braking system) * Emergency release device for spring-loaded cylinders * Drum brakes ----Axle: * 3 x 11 t Gigant axles ----Suspension: * 17.5" air suspension with lifting and lowering system ----Drawbar: * Drawbar 1,800 mm long with 40 mm towing eye ----Electrics / Lighting: * Tire pressure monitoring with display option in the truck display via EBS signal (no installation required on truck side) * 15-pin power plug * 2 additional LED reversing lights (switched via reverse gear) * LED lighting ----General Attachments: * Aluminum air tank * Stainless steel toolbox on the side approx. 1,000 x 300 x 600 mm * Side underride protection * Plastic quarter mudguards * Underrun protection ----Platform: * Zurr-fix external frame, bend 45°, with perforation for lashing equipment, lashing force per point 2,000 kg at 480 mm intervals * Option to install 3,000 kg drop lashing brackets at approx. 600 mm intervals – includes 12 pcs. 3,000 kg lashing brackets per side * Each side with 5 pockets for pipe stanchions 100 x 50 mm in the outer frame (stanchions not included) * 30 mm phenolic plywood floor ----Drum Supports: * 3 galvanized drum supports, secured with container locks and side forklift pockets, center-to-center 800 mm (pocket width 185 mm) * Max. drum diameter 2,600 mm, max. drum width 1,650 mm * Clear width between the support arms approx. 1,775 mm, with crossbar * Drum weight per support: 6,000 kg * Without drive and drum brake * Support arm with tension lock for drum shaft securing * Steel drum shaft, 76 mm diameter, with centering and rotating ends * 2 set collars * 2 centering cones made of polyamide * 4 pcs. 3.2 t lashing eyes on the support arms for customer-side securing of the drum against rotation and unspooling ----Loading height: * Approx. 1,040 mm loaded ----Painting: * Chassis, turntable, drawbar, external frame, underrun protection hot-dip galvanized * Axles painted black ----Information: * Technical GVWR upgrade to 30 t possible Njdpfx Agox Nlkgjxjda * New vehicle with manufacturer’s warranty * Errors and prior sale excepted ----Delivery time: * Available from approx. week 51 / 2026

Condition: new, maximum load weight: 10,500 kg, overall weight: 14,400 kg, axle configuration: 2 axles, loading space length: 6,270 mm, loading space width: 2,470 mm, loading space height: 400 mm, Year of construction: 2026, * ETÜ - TA -R 14.4 ----Brakes: * EBS braking system * Emergency release device for spring-loaded cylinders * Drum brakes ----Axles: * 2 x 7 t Gigant axles Ndedpfx Aex Ipbasgxja ----Suspension: * Parabolic springs with compensating aggregate ----Drawbar / Flange Eye: * Height-adjustable drawbar by 300 mm - drawbar extension by 250 mm to 2,250 mm total length * 40 mm flange towing eye ----Electrics / Lighting: * Tire pressure monitoring with in-cab display option via EBS signal (no installation on truck required) * 15-pin electrical connector * LED tail lights 12 / 24 V * Rear LED beacon (removable) ----General Attachments: * Support crank at the front * Externally mounted, hot-dip galvanized folding supports at rear * Plastic toolbox approx. 858 x 500 x 500 mm, mounted front right on bulkhead * Lateral underrun protection * Plastic quarter mudguards ----Low Bed Deck: * Fixture in front of bulkhead for retrofitting container locks * Bolted smooth-sheet bulkhead * Drop sides made of steel sheet, trapezoidal profile, foldable with drop side spring lifter * Steel tailgate, stowable between ramps - bracket for non-use inside, in front of bulkhead * Bolted rear stanchions * Rear incline approx. 860 mm ----Floor Covering: * 50 mm softwood floor * 12 mm thick, 270 mm wide rubber strip on inner side of loading ramps * 12 mm thick, 210 mm wide rubber strips in the rear incline and outer area of low bed platform (from bulkhead to rear cross member) ----Load Securing: * Slotted external frame, approx. 45° bent, with 2 t lashing capacity every 480 mm * Option to install 3 t folding lashing rings every 600 mm * In the front and rear corners, 1 x 6.3 t lashing ring each * Various holes in the bulkhead and rear cross member for 1.2 t lashing options ----Ramps: * One-piece mechanical mesh loading ramps with spring mechanism for single-person operation, approx. 2,750 x 870 mm (adjustable down to 20 mm spacing) ----Paintwork: * Chassis, drawbar, bulkhead, tailgate, and loading ramps hot-dip galvanized * Axles, springs, air tanks, and flange towing eye painted in black * Sideboards painted RAL 9010 pure white ----Additional Information: * --Reinforced and certified bodywork to EN 12642 XL, including load securing certificate-- * Errors and prior sale excepted * New vehicle with manufacturer's warranty ----Lead Time: Vehicle available immediately ex Egestorf

Condition: used, maximum load weight: 31,000 kg, overall weight: 40,000 kg, axle configuration: > 3 axles, first registration: 07/2024, loading space length: 9,290 mm, loading space width: 2,520 mm, loading space height: 950 mm, * PT 40.0 Profi ----Brakes: * Wabco EBS-E (electronic braking system) * Emergency release system for spring brake cylinders * Drum brakes ----Axles: * 4 x 11-ton Gigant axles ----Suspension: * Air suspension with lifting and lowering system and rapid drop valve ----Drawbar: * Drawbar with 50 mm drawbar eye and height adjustment ----Lighting / Electrical: * EBS multi-voltage system with 12 & 24 V electrical system * 15-pole power connector * LED lighting system 12 / 24 V * LED rotating beacon (removable) at the rear * 2 LED reversing lights (switched via reverse gear) ----General attachments: * Manometer - pressure gauge for load weight determination (axles separated into 2 air suspension circuits) * Lateral impact guard * Swivel supports at the rear of the chassis frame * Mechanically adjustable warning sign packages at the front and rear * Front plastic quarter fenders with splash protection * Rear straight, galvanized steel splash guards with splash protection * Reflective contour strips on the sides and at the rear * Tool box made of galvanized steel sheet, black powder-coated, approx. 1,000 mm wide, 600 mm deep, 300 mm high Ndsdel Tlhrepfx Agxea ----Low-bed platform: * Extension in front of the turntable platform, approx. 490 mm long with 45° corners * ROBOTER welded anti-slip surface on the steel plate of the turntable platform * Hardwood flooring on the running surfaces of the low-bed platform ----Load securing (La-Si-package consisting of): * 1 x 13.4-ton UVV lashing eye on each side in front of the front bulkhead support * 4 holes on each side in the turntable platform, each with a lashing force of 2 tons * 1 pair of lashing eyes (13.4 tons) hanging at the rear on the left and right in front of the rear crossbeam * 4 pairs of UVV lashing rings (10 tons) on each side, swiveling and lowerable, loadable in all directions and recessed in the outer frame * 3 rung pockets on each side with simultaneous 2-ton lashing option ----Widening package: * Hot-dip galvanized mechanical folding outriggers for 3 m overall width (but not in the rear slope) * Beam holder for widening extensions under the chassis on the left in the longitudinal direction ----Excavator arm rest: * Excavator arm rest above the rear axle up to the end crossbeam, approx. 2,100 mm long and approx. 190 mm deep * 2 pairs of 6.4-ton lashing eyes on each side in the excavator arm rest ----Ramps: * Hydraulic, one-piece ramps (approx. 3,000 x 720 mm) mechanically adjustable on the sides * Outer beams of the ramps made of hardwood * Steel construction as preparation for a 6-way control valve ----Loading height: * Loading edge unladen approx. 950 mm +/- 20 mm ----Tires: * Tires 235/75 R 17.5 ----Paint: * Chassis, turntable, folding outriggers, mechanical support legs, ramps hot-dip galvanized * --Axles, air tanks, drawbar painted in a black tone-- ----Info: * Vehicle has a temporary registration in 07/2024, due to a missing tire pressure monitoring system and has not been loaded/used * New vehicle with manufacturer's warranty * Errors and prior sale are subject to change ----Delivery time: * Immediately available from Egestorf

Condition: new, maximum load weight: 8,870 kg, overall weight: 11,900 kg, axle configuration: 2 axles, loading space length: 6,270 mm, loading space width: 2,470 mm, loading space height: 400 mm, Year of construction: 2025, * ETÜ-TA-ER 11.9: ----Brake system: Njdjl Thy Rspfx Agxsda * Electronic braking system (EBS) * Emergency release device for spring-loaded cylinders * Drum brakes ----Axles: * 2 x 5.5 t Gigant axle system ----Suspension: * Parabolic leaf springs with equalizing aggregate ----Drawbar / Flange towing eye: * Height-adjustable drawbar, adjustable by 300 mm * 40 mm flange towing eye ----General attachments: * Jost mechanical support landing gear at the front * Rear external foldable support legs, hot-dip galvanized * Side underrun protection * Plastic quarter mudguards * Plastic toolbox mounted front-right on the bulkhead ----Electrics / Lighting: * TPMS (Tire Pressure Monitoring System) * 15-pin power connector * LED tail lights ----Loading area: * 50 mm softwood floor * 20" container locks fitted at front and rear * Front bulkhead bolted, made from smooth sheet metal * Drop sides made from trapezoidal-profiled steel, foldable with tailgate spring assist * Rear stanchions, hot-dip galvanized and bolted ----Load securing: * Perforated outer frame, approx. 45° edged, with 2 t lashing capacity every 480 mm * Optional installation of 3 t folding lashing brackets every 600 mm (each side fitted with 5 lashing rings) * One 6.3 t lashing ring in each front and rear corner * Various holes in the front and rear cross beams for 1.2 t lashing options ----Ramps: * 1 pair of aluminum approach ramps, approx. 3,310 x 400 mm (load capacity 8 t/pair), suitable for pneumatic-tyred and tracked vehicles * Rear stowage compartment beneath the loading platform, integrated in the chassis ----Paint/Coating: * Chassis, drawbar, front and rear bulkheads hot-dip galvanized * Side board color RAL 9010 pure white * Sides can be painted in any RAL color at extra cost ----Additional information: * New vehicle without registration * Subject to errors and prior sale ----Delivery time: * Immediately available ex Egestorf

Condition: new, maximum load weight: 10,800 kg, overall weight: 14,400 kg, axle configuration: 2 axles, loading space length: 6,270 mm, loading space width: 2,470 mm, Year of construction: 2026, * ETÜ-TA-R 14.4: ----Brakes: * EBS brake system * Emergency release device for spring-loaded brake cylinders * Drum brakes ----Axles: * 2 x 7 t Gigant axles ----Suspension: * Parabolic springs with compensating unit ----Drawbar / Flange Towing Eye: * Drawbar height-adjustable by 300 mm * Drawbar extension by 250 mm to a total length of 2,250 mm ----Electrics / Lighting: * Tire pressure monitoring system with in-cab display via EBS signal (no truck-side installation required) * 15-pin power connector * LED lighting system 12 / 24 V * EBS multi-voltage system for towing vehicles with 12 and 24 V electrics ----General Attachments: * Support winch at the front * External folding support legs at the rear * Plastic toolbox approx. 858 x 500 x 500 mm mounted front right on the bulkhead * Side underrun protection * Plastic quarter mudguards ----Low Loader Deck: * 50 mm softwood floor * Provision in front of the bulkhead for retrofitting container locks * Bolted 400 mm high smooth steel bulkhead * Bolted rear posts * Drop sides with spring assist ----Load Securing: * Perforated outer frame, approximately 45° angled, with 2 t lashing capacity every 480 mm * Option to install 3 t recessed lashings every 600 mm * One 6.3 t lashing ring in each front and rear corner * Various holes for 1.2 t lashing points in the front and rear crossmembers * Profifix lashing rail, centered lengthways, for lashing up to LC 3,000 daN ----Ramps: * One-piece hydraulic mesh loading ramps, approx. 2,750 x 600 mm (collapsible to 20 mm clearance) * Hydraulic flow divider installed in trailer (for hydraulic pump flow from the truck exceeding 40 l/min up to max. 140 l/min) ----Paintwork: * Chassis, drawbar, bulkhead, mechanical folding supports, and loading ramps hot-dip galvanized * Axles, springs, air tanks, front support winch, and flange towing eye painted black * Drop side panels painted in RAL 9010 pure white * Painting of side panels in any RAL color available at extra cost ----Information: Nsdpfx Agerwc R Rsxsda * New vehicle with manufacturer warranty * Subject to misprints and prior sale ----Delivery time: * Immediately available ex-works Egestorf

Condition: new, maximum load weight: 30,740 kg, overall weight: 40,000 kg, axle configuration: > 3 axles, Year of construction: 2026, * T 4: * Wabco EBS-E (electronic braking system) * RDÜ tire pressure monitoring system * Emergency release device for spring brake cylinders * Drum brakes * 4 x 11 t Gigant axles * Air suspension with lifting and lowering device and RtR valve * SmarD on-board system for load weight determination * Warning sign packages front & rear * Reflective contour tape on sides and rear * Removable rotating beacon at the rear * LED lights * Straight drawbar with 50 mm towing eye and infinitely adjustable height * Tool box made of powder-coated steel and spare wheel holder in basket design, mounted on the right side * Enclosed plastic single fenders at the front * Straight steel mudguards at the rear, each with spray suppression (anti-spray system) * Side underrun protection * Turntable platform extended by 520 mm with 45° corners and 3 integrated storage compartments incl. cover, lockable * Chassis made of high-strength fine-grained steel * Floor over turntable platform made of 50 mm softwood, in the low-bed platform made of 60 mm softwood * Outer planks of the loading ramps made of hardwood * 4 stake pockets on each side (no stakes included) with simultaneous 2 t lashing point per pocket * Load securing package consisting of: 2 lashing points 6.4 t at the front left and right on the main frame of the turntable platform * 2 pairs of 13.4 t lashing rings each at the outer frame front and rear, as well as 4 pairs of 10 t lashing rings per side, swiveling and retractable * Loadable in all directions and recessed into the outer frame * 2 pairs of 6.4 t lashing rings in the excavator arm rest area * 8 pairs of galvanized swing-out marker boards for 3 m total width (not at the rear slope) * Widening planks stored in a compartment on the left side * Excavator arm rest above rear axle up to end of approach ramp approx. 2,100 x 740 x 190 mm * Mechanical drop-down supports at the rear * Hydraulic folding ramps with hydraulically adjustable tip, approx. 4,650 x 720 mm incl. hydraulic lateral ramp shifting and load-holding valve * Loading area across the turntable: approx. 2,990 x 2,520 mm * Rear loading area: approx. 6,780 x 2,520 mm * Loading height loaded: approx. 890 mm, +/- 20 mm (incl. 860 mm approach slope) * Flow divider installed * Chassis, turntable, access ramps, flip-out marker boards and mechanical drop-down supports hot-dip galvanized * Axles, drawbar, air tanks, and turntable painted in black * Tires: 235/75 R 17.5 * New vehicle without first registration, with manufacturer warranty Ndedpfx Agsl Tik Noxsa * Subject to errors and prior sale * Immediately available ex Egestorf on the A7

Condition: new, maximum load weight: 10,900 kg, overall weight: 14,400 kg, axle configuration: 2 axles, loading space length: 6,270 mm, loading space width: 2,470 mm, loading space height: 400 mm, Year of construction: 2025, ETÜ-TA-R 14.4 ----Braking system: * EBS electronic braking system * Emergency release mechanism for spring brake cylinders * Drum brakes ----Axles: * 2 x 7 t Gigant axles ----Suspension: * Air suspension ----Tow bar / Flange eye: * Tow bar height-adjustable by 300 mm * Tow bar extension by 250 mm to 2,250 mm Ndedpfx Agsq Dyvyjxja * 40 mm flange towing eye ----Lighting / Electrics: * RDÜ (tyre pressure monitoring system) * LED tail lights 12 / 24 V * 15-pin power connector ----General attachments: * Jost landing gear front * Externally mounted, hot-dip galvanized folding supports at rear * Plastic toolbox, front right, mounted on the bulkhead * Side underrun protection * Plastic quarter mudguards ----Low loader platform: * 50 mm softwood floor * Fittings in front of bulkhead for retrofitting container locks * Bolted flat sheet steel bulkhead * Drop sides made of trapezoidal-profiled steel sheet, folding with drop side lifting springs * Rear steel wall retractable between ramp holders, stowable in front of bulkhead when not in use * Bolted rear stanchions * Rear drive-on slope approx. 860 mm ----Load securing: * Perforated outer frame, approx. 45° angled, with 2 t lashing force every 480 mm * Option to install 3 t folding lashing brackets every 600 mm * 1 x 6.3 t lashing ring in each front and rear corner * Various drillings for 1.2 t lashing points in front bulkhead and rear end crossmember ----Ramps: * One-piece, mechanical mesh ramps with spring assist for single-person operation, approx. 2,750 x 600 mm (collapsible to 20 mm) ----Paintwork: * Hot-dip galvanized chassis as well as tow bar, bulkhead, tailgate, and access ramps * Sideboard colour in RAL 9010 pure white * Painting of side walls in alternative RAL colours available at extra cost ----Info: * --Reinforced and certified body built according to EN 12642 XL including load securing certificate-- * New vehicle with manufacturer’s warranty * Subject to errors and prior sale ----Delivery time: * Available immediately ex Egestorf

Condition: new, maximum load weight: 20,500 kg, overall weight: 27,000 kg, axle configuration: 3 axles, loading space length: 7,000 mm, loading space width: 2,470 mm, Year of construction: 2026, * ETÜ-TR 27.0 Platform: * EBS (Electronic Braking System) * Emergency release device for spring brake cylinders * Drum brakes * 3 x 9 t BPW Eco axles * Air suspension with lifting and lowering system, with RTR function * 1st axle liftable * Last axle as follower steering axle with electro-pneumatic steering lock via PIN reverse gear (locking of the follower axle from the tractor unit for maneuvering purposes - without truck-side installation - assigned to PIN 10 in the 15-pin connector, for maneuvering purposes only, not for use in public road traffic) * SmartBoard control unit as an infotool, with pressure sensors for total axle load display * Tire pressure monitoring with display option in the truck via EBS signal, no truck-side installation required * Fixed central drawbar with 50 mm flanged towing eye (loaded 900 mm, height adjustment at the head board) * Mechanical landing gear at the front, mechanical swing-down supports at the rear of the chassis * Hydraulic flow divider * Continuous side walls (without center posts) up to the run-on ramp * Rear stanchions foldable * Steel rear wall inserted in front of the rear stanchions * Mechanically adjustable warning sign package at front and rear * Tool boxes made of galvanized sheet steel - black powder coated - approx. 650 x 300 x 600 mm, mounted right side * 15-pin power connector * LED tail lights * Detachable LED rotating beacon incl. bracket and installation * 2 x LED reverse lights at vehicle rear (activated via reverse gear) * Flashing LED side marker lights * 60 mm larch / douglas fir wood floor * 400 mm plug-in steel front wall * Perforated outer frame, approx. 45° angled, with provisions for mounting 3 t folding lashing brackets * In each corner 1 x 10 t lashing ring, as well as 2 x 10 t and 3 x 6.3 t lashing rings per side additionally * Various holes in the front and rear cross members for 1.2 t lashing options Nedpfxjr Dpzxj Agxsda * Hydraulic one-piece drive-on ramps, approx. 3,000 x 720 mm, mechanically adjustable sideways * 4-way hydraulic control block for possible retrofit of hydraulic ramp shifting * Chassis, drawbar, front wall, rear manual supports, and drive-on ramps hot-dip galvanized * Axles, air tanks, flanged drawbar eye, and front mechanical landing gear coated in black * Hydraulic flow divider in the trailer (for hydraulic pump output from 40 l to 120 l/min in the truck) * New vehicle with manufacturer’s warranty * Errors and prior sale excepted * Immediately available from Egestorf

Condition: new, maximum load weight: 10,360 kg, overall weight: 14,400 kg, axle configuration: 2 axles, loading space length: 6,270 mm, loading space width: 2,470 mm, loading space height: 400 mm, Year of construction: 2025, * ETÜ-TA-ER 14.4: Ndedpfxopk D Dqe Agxja ----Brakes: * Electronic braking system (EBS) * Emergency release device for spring-loaded cylinders * Drum brakes ----Axles: * GIGANT axles ----Suspension: * Air suspension with lift and lowering system ----Drawbar / Flange drawbar eye: * Height-adjustable drawbar (adjustable by 300 mm) * 40 mm flange drawbar eye ----Electrics / Lighting: * TPMS (Tire Pressure Monitoring System with display option in the truck via EBS signal—no truck-side installation required) * LED lighting system * 15-pin power connector ----General attachments: * Jost landing gear at the front * Externally mounted, hot-dip galvanized folding support legs at the rear * Plastic toolbox mounted on the front wall, right-hand side * Side underrun protection * Plastic quarter mudguards ----Lowbed platform: * 50 mm softwood floor * Preparation for subsequent installation of 20" container locks at the front and rear * Bolted front wall, smooth sheet steel * Drop sides made of trapezoidal-profile sheet steel, foldable with sideboard spring assist * Bolted, hot-dip galvanized rear stakes ----Load securing: * Perforated outer frame, approx. 45° angled, with 2 t lashing capacity every 480 mm * Option to fit 3 t folding lashing rings every 600 mm * One 6.3 t lashing point at each front and rear corner * Various holes in the front wall and end crossmember for 1.2 t lashing options ----Ramps: * 1 pair of aluminum loading ramps approx. 3,310 x 400 mm (load capacity 8 t per pair), suitable for rubber-tired and tracked vehicles; storage compartment underneath the loading platform integrated in the chassis for rear access ----Paintwork: * Chassis, drawbar, front wall, and rear wall hot-dip galvanized * Entire vehicle hot-dip galvanized ----Info: * New vehicle with manufacturer's warranty * Errors and prior sale excepted ----Delivery time: * Immediately available ex Egestorf