Low loader trailer

MÜLLER-MITTELTAL T4, Luftfed., hydr. Klapprampe, Baggerstiel.

Condition: new, maximum load weight: 30,740 kg, overall weight: 40,000 kg, axle configuration: > 3 axles, Year of construction: 2026, * T 4: * Wabco EBS-E (electronic braking system) * RDÜ tire pressure monitoring system * Emergency release device for spring brake cylinders * Drum brakes * 4 x 11 t Gigant axles * Air suspension with lifting and lowering device and RtR valve * SmarD on-board system for load weight determination * Warning sign packages front & rear * Reflective contour tape on sides and rear * Removable rotating beacon at the rear * LED lights * Straight drawbar with 50 mm towing eye and infinitely adjustable height * Tool box made of powder-coated steel and spare wheel holder in basket design, mounted on the right side * Enclosed plastic single fenders at the front * Straight steel mudguards at the rear, each with spray suppression (anti-spray system) * Side underrun protection * Turntable platform extended by 520 mm with 45° corners and 3 integrated storage compartments incl. cover, lockable * Chassis made of high-strength fine-grained steel Itsdpfol Tik Njx Agxof * Floor over turntable platform made of 50 mm softwood, in the low-bed platform made of 60 mm softwood * Outer planks of the loading ramps made of hardwood * 4 stake pockets on each side (no stakes included) with simultaneous 2 t lashing point per pocket * Load securing package consisting of: 2 lashing points 6.4 t at the front left and right on the main frame of the turntable platform * 2 pairs of 13.4 t lashing rings each at the outer frame front and rear, as well as 4 pairs of 10 t lashing rings per side, swiveling and retractable * Loadable in all directions and recessed into the outer frame * 2 pairs of 6.4 t lashing rings in the excavator arm rest area * 8 pairs of galvanized swing-out marker boards for 3 m total width (not at the rear slope) * Widening planks stored in a compartment on the left side * Excavator arm rest above rear axle up to end of approach ramp approx. 2,100 x 740 x 190 mm * Mechanical drop-down supports at the rear * Hydraulic folding ramps with hydraulically adjustable tip, approx. 4,650 x 720 mm incl. hydraulic lateral ramp shifting and load-holding valve * Loading area across the turntable: approx. 2,990 x 2,520 mm * Rear loading area: approx. 6,780 x 2,520 mm * Loading height loaded: approx. 890 mm, +/- 20 mm (incl. 860 mm approach slope) * Flow divider installed * Chassis, turntable, access ramps, flip-out marker boards and mechanical drop-down supports hot-dip galvanized * Axles, drawbar, air tanks, and turntable painted in black * Tires: 235/75 R 17.5 * New vehicle without first registration, with manufacturer warranty * Subject to errors and prior sale * Immediately available ex Egestorf on the A7

Condition: new, empty load weight: 6,600 kg, maximum load weight: 17,400 kg, overall weight: 24,000 kg, axle configuration: 3 axles, loading space length: 6,500 mm, total length: 10,900 mm, suspension: steel, tire size: 235/75 R17,5 (Doppelbereifung), color: silver, gearing type: mechanical, fuel consumption (urban): 1,090 l/100km, Empty weight: 6600kg, permissible total weight: 24000kg, loading space length: 6,500 mmTire size: 235/75 R17.5, 1st axle: , 2nd axle: , 3rd axle: , leaf spring suspension, 3 axle low loader trailer with offset DTS-S 300 - bogie with strong ball bearing ring - foldable rear support - 1 spare wheel holder for 1 electric bike, with wheel fastening kit - 1 spare wheel, same make as basic tires, steel rim - 1 plastic tool box - extensions extendable to 3000mm (not in rear bevel) - storage compartment for wooden planks in the middle of the low load area - wooden planks 70mm for extension to 3000mm Lashing eyes low loader: - with spring jack Support axles + suspension: - SAF - drum brake axles - Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation (rocker compensation) Brake system: - 2-line compressed air brake system - Spring-loaded parking brake Electrics: - 24 volt, multi-chamber lights, yellow LED lighting on the side - 1 LED rotating beacon with holder, switched via parking light (light removable) - 2 pairs of warning signs with double LED lighting and extendable to 3000 mm Floor: - Storage box embedded in the crossing slope to the crank - then with 70 mm softwood floor, steel / checker plate covering in the wheel arch area - Rear bevel with 70 mm softwood floor Loading ramps: Steel ramps 2,800 mm long, 750 mm wide, laterally movable, covered with wood - - 1 pair of ring lashing eyes embedded on the crank at the front, 10 tonnes - 4 pairs of lashing holes in the AR with 5 tonnes each for tensioning belt attachment - 7 pairs Lashing eyes at the top and sides of the outer frame, 10 tonnes each - 1 x at the front on the crank, 6 x in the low bed - 5 pairs of stake pockets in the outer frame, inside 70x40 mm (can be converted to 5 tonne ring lashing eyes for an additional charge) - 2 pairs of additional folding lashing eyes, 10 tonnes each, 1x at the front on the crank, 1x behind the 3rd axle, axles + suspension: - SAF - drum brake axles - parabolic suspension with maintenance-free steel-rubber bearings and mechanical Ac Ijdpfx Astcwkrsgxjtf

Condition: used, mileage: 111,180 km, power: 375 kW (509.86 HP), first registration: 12/2021, fuel type: diesel, overall weight: 32,000 kg, axle configuration: > 3 axles, next inspection (TÜV): 08/2026, color: orange, gearing type: automatic, total width: 2,550 mm, total height: 3,720 mm, loading space length: 6,600 mm, loading space width: 2,480 mm, Equipment: ABS, air conditioning, crane, electronic stability program (ESP), navigation system, parking heater, soot filter, VOLVO FH 510 Platform with Ramps + PK30002 TEC Crane 8x2 Suspension: Air-Air Wheelbase: 5.70 m Payload: 13,451 kg PALFINGER Crane Type: PK30002 TEC Operating hours: 474 h Year: 2021 5x Hydraulic Extensions 4x Hydraulic Outriggers 5th and 6th controls 1x Remote control Steel flatbed body Length: 6.60 m Width: 2.48 m Height from ground: 1.09 m 2x Ramps Equipment: - Engine brake - Digital tachograph - 2x leather seats - Seat heating - 1x bed - Cooling compartment - 2x lift axles - 1x tag axle (lift and steering) - Lane keeping assist - Hill start assist - Side camera - Electric windows - Hands-free system - Radio-media-navigation-phone-Bluetooth - Trailer coupling (with air, ABS, and power connections) We also gladly assist you with financing/leasing options through our partners. All information without guarantee. Subject to errors and prior sale. Itedpfx Agsx Alw Rjxjf

Condition: used, empty load weight: 6,500 kg, maximum load weight: 23,500 kg, overall weight: 30,000 kg, axle configuration: 3 axles, first registration: 01/2008, next inspection (TÜV): 03/2024, loading space length: 8,000 mm, loading space width: 2,520 mm, loading space height: 910 mm, suspension: steel, tire size: 235/75R17.5, color: orange, mileage: 1,001 km, gearing type: other, driver cabin: other, Equipment: ABS, Vehicle location: Bovenden, leaf suspension, 3-axle, BPW axles, turntable, ABS (anti-lock braking system), lashing eyes, hydr. ramps, rear support, aluminum side bumpers, twin tyres, storage box Superstructure: Hydr. ramps, can be widened to 3m. BPW axles, drum brakes, lashing rings on the outside. Ramp length approx. 4000mm! ACCESSORIES WITHOUT WARRANTY, subject to alterations, prior sale and errors excepted! - . Iedpfx Agjqpgtmjxjtf

Condition: new, empty load weight: 9,650 kg, maximum load weight: 30,350 kg, overall weight: 40,000 kg, axle configuration: > 3 axles, loading space length: 9,740 mm, loading space width: 2,550 mm, suspension: air, tire size: 235/75 r17,5 zoll, Year of construction: 2026, Equipment: ABS, center pivot plate, 4-AXLE LOWBED TRAILER WITH TOP-SPEC EQUIPMENT! => HOT-DIP GALVANIZED (CHASSIS FRAME, BOGIE FRAME, ACCESS RAMPS) => FULL AIR SUSPENSION => WITH LIFTING AND LOWERING FUNCTION (REAR AXLE MODULE!) => SAF LOWBED AXLES => LASHING PACKAGE => OUTER FRAME WITH PERFORATIONS FOR ADDITIONAL LASHING POINTS => CLEAT STRIPS AT REAR OF ACCESS SLOPE => 6 LASHING POINTS IN THE EXCAVATOR ARM TROUGH AT THE REAR => LONG ONE-PIECE ACCESS RAMPS => LOW APPROACH ANGLE Permissible gross weight: 40,000 kg Payload approx. 30,350 kg Chassis frame hot-dip galvanized Bogie frame hot-dip galvanized Access ramps hot-dip galvanized Air suspension SAF axle with drum brakes EBS electronic braking system Tyres: 235/75R17.5 – 16 units Lowbed length approx. 7,160 mm Trough for excavator arm resting, approx. 3,000 x 730 x 180 mm at rear of lowbed 4 pairs of 10-ton recessed lashing rings in lowbed 2 pairs of 10-ton recessed lashing rings in raised deck 4 pairs of 3-ton lashing points on outer frame of lowbed 3 pairs of 6-ton lashing eyes on outer frame 4 pairs of stake pockets in outer frame of raised deck 4 pairs of stake pockets in outer frame of lowbed 3-meter widening kit with folding outriggers (flat, no slope) Itsdpfx Aohvxgzsgxef 4 x warning panels with lights Rotating beacon at rear LARGE STEEL STORAGE BOX under the loading area 2 storage compartments with hinged lids in raised deck Hydraulic ramp lifters 1-piece ramps, approx. 3,150 x 750 mm Softwood floor on loading area and ramps 40,000 kg GVW only with special permit as per Section 70 => Delivery freight costs: €2.90 plus VAT per km => Prices ex works D-86368 Gersthofen Your direct contact: Mr. Hauptmann Tel. DOLL Fahrzeugbau *Subject to prior sale and modifications!* *Price valid ex works D-86368 Gersthofen* *Sale to commercial customers only!* *Images may differ and are for general guidance only — may show/accessorise options available at extra cost*

Condition: new, machine/vehicle number: 2dff0c136c85096f36822a0bb, empty load weight: 7,150 kg, maximum load weight: 16,850 kg, overall weight: 24,000 kg, axle configuration: 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction Turntable with strong ball bearing slewing ring, storage box embedded in turntable front end Folding rear support 2 wheel chocks with holder Aluminum side collision protection Rear spray flaps across the entire width Widenings can be extended to 3,000 mm (not in the rear slope) (However, the track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Storage compartment for wooden planks in the middle of the cargo bed Wooden planks 70 mm for widening to 3000 mm Low loader lashing eyes 3 pairs of lashing points each 10 to integrated in the floor at the front 6 pairs of lashing points at the top and sides, each 10 tons, integrated in the outer frame 1 x to the neck area remaining distributed in between Spacing not greater than 1200 mm 1 x rear slope 5 pairs of stake pockets embedded in the outer frame, inside 70 x 40 mm, (can be converted to 5 to. ring lashing eyes, not included in the scope of delivery) Towing equipment Trailer turntable Ijdpfoi Riy Esx Agxetf Drawbar with tested 40 mm drawbar eye Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation axle load compensation (rocker compensation) Brake system 2-line compressed air brake system Colored line routing for easy servicing. Spring-loaded parking brake Incl. 2 swap-proof coupling heads at the front, with connecting lines to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable, Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Wheels and tires 235 / 75 R 17,5 at the choice of the manufacturer Steel rims in twin arrangement, factory silver Electrical system 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin interchangeable plugs at the front, with connecting cable, 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Front area steel floor, then with 70 mm softwood floor, steel/checker plate flooring in the wheel housing area Rear slope with 70 mm softwood floor Deep loading area incl. rear slope 8,200 mm Drive-on ramps Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways Covered with wood Incl. with spring lift support Operating instructions With an axle load of 10,000 kg, a special permit is required, only indivisible loads possible!!! The specified total weight is technically possible; depending on the load, the total weight may not be achieved while complying with the permissible axle/support and fifth-wheel loads. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Country of registration: Germany with Dekra approval and expert opinion (according to §13 EG - FGV) 24/7 service hotline Prepared for two-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white on the sides and red on the rear Paint finish Frame DB 7350 nova gray 10-year warranty against rusting through Drawbar Galvanized or black, at the manufacturer's choice Drive-on ramps Hot-dip galvanized Attention: Archive pictures!

Condition: new, maximum load weight: 14,400 kg, overall weight: 19,000 kg, axle configuration: 2 axles, loading space length: 6,270 mm, loading space width: 2,470 mm, loading space height: 400 mm, Year of construction: 2025, * ETÜ-TA-ER 19.0: * Wabco EBS-E (electronic braking system) * RDÜ tire pressure monitoring system * Emergency release device for spring brake cylinders * Drum brakes * 2 x 11 ton Gigant axles * Air suspension with lifting and lowering system * Drawbar with 50 mm flange eye and height adjustment of 110 mm via offset plate * Jost landing gear at the front * External folding supports at the rear * Plastic toolbox approx. 750 x 350 x 300 mm, mounted on the right side * Side underrun protection * Plastic quarter mudguards * 15-pin electrical connector * Multi-chamber tail lights * Reinforcement package on the chassis for drill rig transport * 50 mm softwood floor, clamped design * Fixture for retrofitting container locks in front of the bulkhead * Bolted bulkhead made of smooth sheet metal * Split side walls made of trapezoidal-profiled steel sheet, foldable with a central folding stanchion * Steel rear wall, retractable between the ramps – storage holder inside in front of the bulkhead when not in use * Rear stanchions bolted * Perforated outer frame, angled approx. 45 degrees, with 2 ton lashing capacity every 480 mm * Option to install 3 ton drop lashing rings every 600 mm * Load securing package: in each corner at the front and rear, 1 x 10 ton UVV lashing ring; on each side, 2 x 8 ton UVV recessed lashing rings in the outer frame; various holes in the bulkhead and end crossmember for 1.2 ton lashing options * One-piece slide-in ramps, 12 t/pair of ramps, approx. 2,750 x 620 mm * Rear approach angle approx. 860 mm * Chassis, drawbar, bulkhead, tailgate, folding supports, and ramps hot-dip galvanized * ---Axles, air reservoir, flange towing eye, and landing gear painted in black--- * Unloaded loading height approx. 940 mm * Loaded loading height approx. 910 mm * Wheelbase: 1,810 mm * Tires: 235/75R17.5 Iedpemi Tcqsfx Agxotf * Vehicle is hot-dip galvanized * New vehicle with manufacturer warranty * Errors and prior sale excepted * Available immediately from Egestorf