Used Müller-Mitteltal Special Purpose Trailers for sale (257)

Condition: new, maximum load weight: 23,830 kg, overall weight: 30,000 kg, axle configuration: 3 axles, loading space length: 8,460 mm, loading space width: 2,520 mm, Year of construction: 2026, * T3 Profile 30.0: ----Brakes: * EBS braking system * Emergency release system for spring brake cylinders * Drum brakes ----Axles: * 3 x 11-ton BPW Eco axles ----Suspension: * Parabolic springs ----Drawbar: * Drawbar with 40 mm drawbar eye and height adjustment via coil spring and tension lock ----Electrical System / Lighting: * TPMS (tire pressure monitoring system) * Multi-voltage system * LED taillights * Rotating beacon (removable) at the rear * 15-pin power connector ----General Components: * Mechanical axle equalization at the rear * Side underrun protection * Swivel supports at the rear on the chassis frame * Mechanically adjustable warning sign packages at the front and rear * Front mudguards made of molded plastic and straight, galvanized steel splash guards at the rear, each with splash protection * Reflective contour tape on the sides and rear ----Low-Loader Platform: * Folding cover (hot-dip galvanized) for the tool compartment in the turntable platform * 4 lashing points on each side (but no lashing bars included) with simultaneous lashing capability * 6 pairs of mechanical folding outriggers for a total width of 3 m (but not in the rear slope) * Extension planks stored in the center of the loading area ----Load Securing (LaSi Package): * 2 lashing eyes (6.4 tons) at the front left and right on the main frame of the turntable platform * 5 pairs of UVV lashing rings, swiveling and lowerable, loadable in all directions and embedded in the outer frame - 13.4 tons in the corners, otherwise 10 tons ----Excavator Arm Rest: * Excavator arm rest extending over the rear axle to the end carrier, approx. 2,100 mm long (2 pairs of 6.4-ton lashing rings on each side in the excavator arm rest) ----Ramps: * Hydraulically operated, one-piece ramps (approx. 3,000 x 720 mm) * Hydraulic side ramp adjustment ----Loading Area: * Over the turntable: approx. 1,960 x 2,520 mm * Rear loading area: approx. 6,500 x 2,520 mm (including 860 mm approach slope) ----Loading Height: * Unladen: approx. 910 mm ----Tires: * 235/75 R 17.5 twin tires ----Paintwork: * Chassis, turntable, drawbar and ramps hot-dip galvanized * Axles, springs, air tanks, etc. painted in a black shade * Vehicle is hot-dip galvanized ----Information: Njdex Ipb Hopfx Adhelg * --Technically, a maximum permissible total weight of 30,000 kg is possible-- * New vehicle with manufacturer's warranty * Errors and prior sale excepted ----Delivery Time: * Available for immediate delivery from Egestorf

Condition: new, maximum load weight: 17,650 kg, overall weight: 24,000 kg, axle configuration: 3 axles, loading space length: 9,230 mm, loading space width: 2,480 mm, Year of construction: 2026, * TP 30.0 with 3 cable drum supports ----Braking system: Nlodpfx Ajx Nli Nodhjg * Wabco TEBS (electronic braking system) * Emergency release mechanism for spring brake cylinders * Drum brakes ----Axles: * 3 x 11 t Gigant axles ----Suspension: * Air suspension 17.5" with lifting and lowering device ----Drawbar: * Drawbar 1,800 mm long with 40 mm towing eye ----Electrics / Lighting: * Tire pressure monitoring with display capability in the truck dashboard via EBS signal -without truck-side installation- * 15-pin power connector * 2 additional LED reversing lights (activated via reverse gear) * LED lighting ----General attachments: * Aluminum air tank * Stainless steel side-mounted toolbox approx. 1,000 x 300 x 600 mm * Side underrun protection * Plastic quarter mudguards * Underride guard ----Flatbed: * Zurr-fix external frame, 45° angled with hole pattern for lashing equipment, lashing capacity per lashing point 2,000 kg at a spacing of 480 mm * Installation of 3,000 kg drop lashing brackets at approx. 600 mm intervals possible - delivery includes 12 x 3,000 kg lashing brackets per side * 5 pockets per side for stake posts 100 x 50 mm in the outer frame -stake posts not included in delivery- * 30 mm phenolic plywood flooring ----Drum supports: * 3 galvanized drum supports secured by container locks, with lateral forklift pockets, center/center 800 mm apart (pocket width 185 mm) * Maximum drum diameter 2,600 mm and maximum drum width 1,650 mm * Clear width between the support arms approx. 1,775 mm, with cross connection * Maximum drum weight per cable drum support 6,000 kg * Without drive and drum brake * Support arm with clamp lock for securing the drum shaft * Steel drum shaft 76 mm diameter with centering and rotatable ends * 2 stop rings * 2 centering cones made of polyamide * 4 x 3.2 t lashing eyes on the support arms for customer-side securing of the drum against rotation and unwinding ----Loading height: * Loaded approx. 1,040 mm ----Paintwork/Finish: * Chassis, turntable, drawbar, outer frame, underride guard hot-dip galvanized * Axles painted in a shade of black ----Information: * Technical upgrade to 30 t GVW possible * New vehicle with manufacturer’s warranty * Subject to errors and prior sale ----Delivery time: * Available from calendar week 51 / 2026

Condition: new, maximum load weight: 17,650 kg, overall weight: 24,000 kg, axle configuration: 3 axles, loading space length: 9,230 mm, loading space width: 2,480 mm, Year of construction: 2026, * TP 30.0 with 3 cable drum supports ----Braking system: * Wabco TEBS (electronic braking system) * Emergency release device for spring brake cylinders * Drum brakes ----Axles: * 3 x 11 t Gigant axles ----Suspension: * 17.5" air suspension with lifting and lowering facility ----Drawbar: * Drawbar 1,800 mm long with 40 mm towing eye ----Electrics / Lighting: * Tyre pressure monitoring with display option in the truck dashboard via EBS signal (no truck-side installation required) * 15-pin power connector Nljdpex Nlkaofx Adhjg * 2 additional LED reversing lights (switched via reverse gear) * LED lighting ----General attachments: * Aluminium air tank * Stainless steel side toolbox approx. 1,000 x 300 x 600 mm * Side underrun protection * Plastic quarter mudguards * Rear underrun protection ----Platform: * Zurr-fix external frame, 45° angled, perforated for lashing devices, lashing capacity per lashing point 2,000 kg at a distance of 480 mm * Installation of 3,000 kg folding lashing rings at approx. 600 mm spacing possible - each side comes with 12 x 3,000 kg lashing rings supplied * Each side features 5 pockets for pipe stanchions 100 x 50 mm in the outer frame (pipe stanchions not included) * 30 mm phenolic resin-coated plywood floor ----Cable drum supports: * 3 galvanized cable drum supports, secured via container locks with side forklift pockets centre-to-centre 800 mm (pocket width 185 mm) * Max. drum diameter 2,600 mm and max. drum width 1,650 mm * Clear width between support arms approx. 1,775 mm, with cross-brace * Max. drum weight per support: 6,000 kg * Without drive or drum brake * Support arm with clamping lock for securing the drum shaft * Steel drum shaft, 76 mm diameter, with centering and rotating ends * 2 retaining collars * 2 centring cones made of polyamide * 4 x 3.2 t lashing eyes on the support arms to secure the drum against unintentional rotation and unwinding (provided by customer) ----Loading height: * approx. 1,040 mm loaded ----Paintwork/finish: * Chassis, turntable, drawbar, outer frame, and underrun protection hot-dip galvanized * Axles painted in black

Condition: new, maximum load weight: 38,620 kg, overall weight: 50,000 kg, axle configuration: > 3 axles, Year of construction: 2026, T5 Profile 50.0: ----Brakes: * Wabco EBS (electronic braking system) * Emergency release device for spring brake cylinders * Drum brakes ----Axles: Nledpfx Adexptn Doheg * 5 x 11 t Gigant axles * 3rd axle liftable (ride height +30 mm when lifted) * Last axle steerable (locking of trailing axle can be performed from the cab for maneuvering purposes, without installation on the truck side, as well as additionally by switch on the trailer); lock must be disengaged before driving on public roads * Forced lifting and forced lowering of the lift axle for maneuvering purposes (truck-side installation required) with speed-dependent control via the EBS electronics ----Suspension: * Air suspension, lifting and lowering system with RtR valve ----Drawbar: * Drawbar 1,500 mm long with 50 mm towing eye and manual height adjustment ----Electrics / Lighting: * Smartboard as infotool with pressure sensors to display total axle load per axle group * Tire pressure monitoring with display option in the truck via EBS signal (no truck-side installation required) * LED lighting system 12/24 V * Removable LED beacon (rear) ----General Attachments: * Mechanical warning sign package for 3 m total width * Toolbox made of galvanized steel sheet approx. 650 x 300 x 600 mm, mounted left side * Plastic wheel arches front axle and galvanized steel sheet mudguards on rear axle ----Low Loader Platform: * Turntable platform extension with 45° corners and 3 storage compartments with lockable folding lids (lids open to the rear) * Shortened low bed platform by 500 mm to 6,280 mm including extended stepped transition 500 mm forwards * Rubber covering on foldable frame, approach slope, and on the running surface of the low loader platform * Bamboo wood between the longitudinal beams in front of the excavator stick holder ----Load Securing (LaSi Package): * 2 x 6.4 t lashing rings at the front corners * 2 x 13.4 t UVV-compliant lashing points each at the front and rear side corners * 5 x 10 t UVV-compliant lashing rings per side (swiveling and lowerable, loadable in all directions) * 4 stake pockets per side, also 2 t lashing capability * 1 x 16 t UVV-compliant lashing point on the rear cross member ----Widening: * Extendable and foldable widening outriggers for 3 m overall width (board bracket holder under chassis, right side) ----Excavator Stick Holder: * Continuous excavator stick holder with reinforced profile from last axle to end beam, approx. L=2,350 x W=770 x H=270 mm, 2 pairs of 6.4 t UVV-compliant lashing rings on the sides of the stick holder ----Ramps: * Hydraulic folding ramp with double-acting hydraulics and extendable tip section, approx. 4,650 x 720 mm incl. load-holding valves and hydraulic side shift ----Rear Support: * Hydraulic rear support ----Hydraulics: * Hydraulic flow divider (for hydraulic pump outputs in the truck above 40 l/min, max. 140 l/min) ----Loading Height: * Loaded: 890 mm +/- 20 mm (via air suspension) ----Loading Area Dimensions: * Deck above turntable: 2,600 + 390 x 2,520 mm * Low bed area: 6,280 + 500 x 2,520 mm incl. 860 mm approach slope ----Paintwork: * Chassis, bogie, drawbar, extension consoles, access ramps hot-dip galvanized * Towing fork, axles, hydraulic axle supports, as well as air tanks painted in black ----Information: * New vehicle with manufacturer’s warranty * Subject to errors and prior sale ----Delivery Time: Immediately available*

Condition: used, maximum load weight: 23,180 kg, overall weight: 30,000 kg, axle configuration: 3 axles, first registration: 03/2019, loading space length: 8,300 mm, loading space width: 2,500 mm, loading space height: 900 mm, total length: 10,805 mm, total width: 2,550 mm, Total weight: 24,000 kg / 30,000 kg Unladen weight: 6,820 kg Payload: 17,180 kg / 23,180 kg Overall length: 10,805 mm Loading length: approx. 8,300 mm overall / approx. 6,500 mm low-bed including rear extension Width: 2,550 mm Loading height: 900 mm Further information: Wheel recesses Ramp extensions Ramps can be shifted laterally Rotating beacon Warning signs at the front and rear Nlsdpfx Adjzwkkrohsg Twin tires BPW axles Plastic toolbox Folding rear support Excavator arm recess approx. 2,400 mm x 800 mm Large lashing kit Lashing eyes in the outer frame Storage compartment in the gooseneck

Condition: new, maximum load weight: 10,750 kg, overall weight: 14,400 kg, axle configuration: 2 axles, loading space length: 7,000 mm, loading space width: 2,470 mm, loading space height: 400 mm, Year of construction: 2026, * ETÜ-TA-R 14.4: ----Brakes: * EBS braking system * Emergency release system for spring brake cylinders * Drum brakes ----Axles: * 2 x 7-ton Gigant axles ----Suspension: * Parabolic springs with equalizing unit ----Drawbar / Flange coupling: * Drawbar with 300 mm height adjustment * Drawbar extension by 250 mm to 2,250 mm * 40 mm flange coupling ----Electrical system / Lighting: * TPMS tire pressure monitoring system * 15-pin power connector * LED lighting ----General attachments: * Support winch at the front * Outboard folding supports at the rear * Plastic tool box approx. 858 x 500 x 500 mm on the front right outside on the front panel * Lateral impact protection * Plastic quarter fenders ----Low-loader platform: * 50 mm hardwood flooring * In front of the front panel and rear slope, provision for retrofitting container locking mechanisms for the transport of 20" containers * Screwed front panel made of smooth sheet metal * Steel sheet metal side walls - trapezoidal profile - foldable in the middle, divided 1x * Steel rear wall can be slid in between the ramp brackets when not in use, inside in front of the front panel * Rear crossbeams screwed on ----Load securing: * Perforated outer frame approx. 45 degrees bent with 2-ton lashing force every 480 mm * Installation of 3-ton drop-side lashing eyes possible every 600 mm * In the corners, front and rear, 1 x 6.3-ton lashing point each Njdpfev D Tcbjx Adholg * In the front and end beam, various holes for 1.2-ton lashing options * Profifix lashing rail in the longitudinal axis in the middle for lashing up to LC 3000 daN ----Ramps: * One-piece mechanical grating ramps with spring mechanism for single-person operation approx. 2,750 x 600 mm (can be pushed together to 20 mm) * Approach angle at the rear approx. 860 mm chassis ----Wheelbase: * Wheelbase 1,140 ----Painting: * Drawbar, front panel, rear door, folding supports and ramps hot-dip galvanized * Axles, springs, air tanks, flange coupling and support winch painted in a black tone * Painting of the side walls in RAL - 9010 pure white ----Information: * Reinforced and certified body according to EN 12642 XL incl. load securing certificate * New vehicle with manufacturer's warranty * Errors and prior sale reserved ----Delivery time: * Immediately available from Egestorf

Condition: new, maximum load weight: 10,750 kg, overall weight: 14,400 kg, axle configuration: 2 axles, loading space length: 7,000 mm, loading space width: 2,470 mm, loading space height: 400 mm, Year of construction: 2026, * ETÜ-TA-R 14.4: ----Brakes: * EBS braking system * Emergency release device for spring-loaded cylinders * Drum brakes ----Axle: * 2 x 7-ton Gigant axles ----Suspension: * Parabolic springs with compensating unit ----Drawbar / Flange coupling: * Height-adjustable drawbar by 300 mm * Drawbar extension by 250 mm to 2,250 mm * 40 mm flange coupling ----Electrical system / Lighting: * TPMS tire pressure monitoring system * 15-pin power connector * LED lighting ----General components: * Front support jack * Outboard folding supports at the rear * Plastic toolbox approx. 858 x 500 x 500 mm on the front right outside of the front wall * Lateral impact protection * Plastic quarter fenders ----Low-loader platform: * 50 mm softwood flooring * In front of the front wall and rear slope, provision for the subsequent installation of container locking mechanisms for the transport of 20" containers * Bolted front wall made of smooth sheet metal * Steel sheet metal side walls - trapezoidal profile - foldable, divided in the middle 1x * Steel rear wall can be slid in between the ramp brackets when not in use, positioned inside in front of the front wall * Rear crossbars bolted on Nljdov Eq Evjpfx Adhjg ----Load securing: * Perforated outer frame, approx. 45 degrees angled, with 2-ton lashing force every 480 mm * Installation of 3-ton chain lashing brackets possible every 600 mm * In the corners, front and rear, 1 x 6.3-ton lashing point each * Various drill holes in the front and end crossmembers for 1.2-ton lashing options * Profifix lashing rail in the longitudinal axis in the middle for lashing options up to LC 3000 daN ----Ramps: * One-piece mechanical grid grating ramps with spring mechanism for single-person operation, approx. 2,750 x 600 mm (can be pushed together to 20 mm) * Approach slope at the rear approx. 860 mm chassis ----Wheelbase: * Wheelbase 1,140 ----Painting: * Drawbar, front wall, tailgate, folding supports and ramps hot-dip galvanized * Axles, springs, air tanks, flange coupling and support jack painted in a black tone * Painting of the side walls in RAL 9010 pure white ----Information: * Reinforced and certified superstructure according to EN 12642 XL incl. load securing certificate * New vehicle with manufacturer's warranty * Errors and prior sale reserved ----Delivery time: * Immediately available from Egestorf

Condition: used, maximum load weight: 31,000 kg, overall weight: 40,000 kg, axle configuration: > 3 axles, first registration: 07/2024, loading space length: 9,290 mm, loading space width: 2,520 mm, loading space height: 950 mm, * PT 40.0 Profi ----Brakes: * Wabco EBS-E (electronic braking system) * Emergency release system for spring brake cylinders * Drum brakes ----Axles: * 4 x 11 to. Gigant axles ----Suspension: * Air suspension with lifting and lowering system and rapid lowering valve ----Drawbar: * Drawbar with 50 mm drawbar eye and height adjustment ----Lighting / Electrical: * EBS multi-voltage system with 12 & 24 V electrical system * 15-pin electrical connector * LED lighting system 12 / 24 V * LED rotating beacon (removable) at the rear * 2 LED reversing lights (switched via reverse gear) ----General components: * Pressure gauge - pressure indicator for determining payload (axles separated into 2 air suspension circuits) * Side underrun protection * Swivel supports at the rear of the chassis frame * Mech. adjustable warning sign packages at the front and rear * Front plastic quarter fenders with splash guard * Rear straight, galvanized steel side skirts with splash guard * Reflective contour strip on the side and rear * Tool box made of galvanized steel sheet, black powder-coated, approx. 1,000 mm wide, 600 mm deep, 300 mm high ----Low-loader platform: * Extension in front of the turntable platform approx. 490 mm long with 45° corners * ROBOTER welded anti-slip coating on the steel plate of the turntable platform * Hardwood flooring on the running surfaces of the low-loader platform ----Load securing (La-Si package consisting of): * 1 x 13.4 to. UVV lashing eye to the left and right in front of the front bulkhead beam * 4 holes on each side in the turntable platform, each with a lashing force of 2 to. * 1 pair of lashing eyes (13.4 to.) hanging at the rear left and right in front of the rear beam Nlsdpjl Tnu Asfx Adhsg * 4 pairs of UVV lashing rings (10 to.) on each side, swiveling and lowering, capable of withstanding loads in all directions and recessed in the outer frame * 3 rung pockets on each side with simultaneous 2 to. lashing option ----Widening package: * Hot-dip galvanized mech. folding outriggers for 3 m overall width (however, not in the rear slope) * Beam holder for widening under the chassis on the left in the longitudinal direction ----Excavator arm rest: * Excavator arm rest above the rear axle up to the end beam approx. 2,100 mm long and approx. 190 mm deep * 2 pairs of 6.4 to. lashing eyes on each side in the excavator arm rest ----Ramps: * Hydr. one-piece access ramps (approx. 3,000 x 720 mm) mech. adjustable on the side * Outer planks of the access ramps made of hardwood * Steel structure as preparation for a 6-way control valve ----Loading height: * Unladen loading edge approx. 950 mm +/+ 20 mm ----Tires: * Tires 235/75 R 17.5 ----Paintwork: * Chassis, turntable, folding outriggers, mech. support legs, access ramps hot-dip galvanized * Axles, air tank, drawbar painted in a black tone ----Information: * Vehicle has a day registration in 07/2024, due to the missing tire pressure monitoring system and has not been loaded/used * New vehicle with manufacturer's warranty * Errors and prior sale reserved ----Delivery time: * Available for immediate delivery from Egestorf

Condition: new, maximum load weight: 30,440 kg, overall weight: 40,000 kg, axle configuration: > 3 axles, Year of construction: 2026, Equipment: ABS, T 4 Profi 40.0 ----Brakes: * Wabco EBS-E (electronic braking system) * Emergency release system for spring-loaded cylinders * Drum brakes ----Axles: * 4 x 11-ton Gigant axles ----Suspension: * Air suspension with lifting and lowering system and RtR valve ----Drawbar: * Straight drawbar with 50 mm drawbar eye and stepless height adjustment ----Electrical System / Lighting: * Tire pressure monitoring system with display option in the truck display via EBS signal - without truck-side installation - * SmartBoard as an information tool with pressure sensors for axle load display per axle group * 15-pin power connector * LED rear lights * LED marker lights (removable) at the rear ----General Components: * Warning sign packages at the front & rear * 2 x toolboxes made of galvanized, powder-coated steel sheet, approx. 650 x 300 x 600 mm, on the right side * Closed plastic fender at the front * Straight steel mudguards at the rear, each with splash protection (spray mist suppression) * Lateral impact protection ----Low-bed Platform: * Extension of the turntable platform by 520 mm with 45° corners and 3 recessed storage compartments incl. lids and locking mechanism * Floor over the turntable platform made of 50 mm needlewood, and in the low-bed platform made of 60 mm needlewood * Rubber coating 20 mm instead of wooden floor in the running area with a low-bed length of 6,780 mm including the access ramp * Rubber coating on the access ramp, left and right, approx. 860 mm long * 4 lashing eye pockets on each side (however, no lashing bars included) with simultaneous 2-ton lashing capability ----Chassis: * Chassis made of high-strength fine-grain steel ----Load Securing (Lasi - Package): Turntable Platform: * 2 pairs of 13.4-ton lashing eyes in the outer frame of the turntable platform Low-bed: * 4 pairs of 10-ton lashing eyes on each side of the outer frame, retractable and loadable in all directions * 2 pairs of 13.4-ton swiveling lashing eyes on each side at the rear ----Ramps: * Rubber coating on the folding access ramps * Hydraulic folding ramps with hydraulic extendable front section, approx. 4,650 x 720 mm * Hydraulic lateral ramp adjustment & load holding valves ----Rear Support: * Hydraulic rear support ----Width Extension: * 8 pairs of galvanized folding outriggers for 3 m overall width (however, not in the rear slope) * Width extension boards stored in a compartment on the left side ----Excavator Arm Rest: * Excavator arm rest above the rear axle to the end of the access ramp, approx. L=2,100 mm x W=740 x D=190 mm * 2 pairs of 6.4-ton lashing eyes on the side in the excavator arm rest ----Hydraulics: Nledpfsylfvgox Adhog * Hydraulic flow divider in the trailer (with hydraulic pump output in the truck of over 40 - max. 120 l/min.) ----Loading Dimensions: * Rear loading area: approx. 6,780 x 2,520 mm (incl. 860 mm access ramp) * Loading area above the turntable: approx. 2,990 x 2,520 mm ----Loading Height: * approx. 890 mm, +/- 20 mm ----Painting: * Reflective contour striping on the sides and at the rear * Chassis, turntable, access ramps, and folding outriggers hot-dip galvanized * Axles, drawbar, air tanks, and turntable painted in a black color ----Information: * New vehicle with manufacturer's warranty * Subject to errors and prior sale ----Delivery Time: * Immediately available from Egestorf

Condition: new, maximum load weight: 30,440 kg, overall weight: 40,000 kg, axle configuration: > 3 axles, Year of construction: 2026, Equipment: ABS, T 4 Profi 40.0 ----Brakes: * Wabco EBS-E (electronic braking system) * Emergency release system for spring brake cylinders * Drum brakes ----Axles: * 4 x 11 ton Gigant axles ----Suspension: * Air suspension with lifting and lowering system and rapid release valve (RtR valve) ----Drawbar: * Straight drawbar with 50 mm drawbar eye and stepless height adjustment ----Electrical System / Lighting: * Tire pressure monitoring system with display option in the truck display via EBS signal - without truck-side installation - * SmartBoard as an information tool with pressure sensors for axle load display per axle group * 15-pole power connector * LED tail lights * Detachable LED marker lights at the rear ----General Components: * Warning sign packages at the front and rear * 2 x toolboxes made of galvanized, powder-coated sheet steel, approx. 650 x 300 x 600 mm, on the right side * Closed plastic fender at the front * Straight steel splash guards at the rear, each with a spray guard (spray mist reduction) * Side impact protection ----Lowboy Platform: * Extension of the turntable platform by 520 mm with 45° corners and 3 recessed storage compartments incl. cover and lockable * Floor over the turntable platform made of 50 mm and in the lowboy platform made of 60 mm hardwood * 20 mm rubber coating instead of wooden floor in the running track area with a lowbed length of 6,780 mm including the ramp * Rubber coating on the ramp on the left and right sides, approx. 860 mm long * 4 lashing eye sockets on each side (but no lashing bars included) with simultaneous 2-ton lashing capability ----Chassis: * Chassis made of high-strength fine-grain steel ----Load Securing (Lasi Package): Turntable Platform: * 2 pairs of 13.4-ton lashing eyes in the outer frame of the turntable platform Lowbed: * 4 pairs of 10-ton lashing rings on each side in the outer frame, retractable and loadable in all directions * 2 pairs of 13.4-ton swiveling lashing rings at the rear on each side ----Ramps: * Rubber coating on the folding ramps * Hydraulic folding ramps with hydraulically extendable front section, approx. 4,650 x 720 mm * Hydraulic side ramp adjustment & load holding valves ----Rear Support: * Hydraulic rear support ----Widening: * 8 pairs of galvanized folding outriggers for a total width of 3 m (but not in the rear ramp) * Widening boards stored on the left side in a storage compartment ----Excavator Arm Rest: * Excavator arm rest above the rear axle to the end of the ramp, approx. L = 2,100 mm x W = 740 x D = 190 mm * 2 pairs of 6.4-ton lashing rings on the side in the excavator arm rest Nsdjylfvmjpfx Adhelg ----Hydraulics: * Hydraulic flow divider in the trailer (with hydraulic pump output in the truck of over 40 - max. 120 liters/min.) ----Loading Dimensions: * Rear loading area: approx. 6,780 x 2,520 mm (incl. 860 mm ramp) * Loading area over the turntable: approx. 2,990 x 2,520 mm ----Loading Height: * approx. 890 mm, +/- 20 mm ----Painting: * Reflective contour strip on the side and rear, * Chassis, turntable, ramps, and folding outriggers hot-dip galvanized * Axles, drawbar, air tanks, and turntable painted in a black tone ----Information: * New vehicle with manufacturer's warranty * Errors and prior sales are subject to change ----Delivery Time: * Immediately available from Egestorf

Condition: new, maximum load weight: 13,490 kg, overall weight: 18,000 kg, axle configuration: 2 axles, loading space length: 7,000 mm, loading space width: 2,480 mm, Year of construction: 2025, TRA-Kombi 18.0: * 3 in 1 = suitable for roll-off containers, skip loaders, and as a low-loader ----Brakes: * EBS-E (electronic braking system) * Emergency release system for spring brake cylinders * Drum brakes ----Axles: * 2 x 10.5-ton Gigant axles ----Suspension: * Air suspension with manual lowering at the rear Nlsdpfswb Rakex Adhsg ----Drawbar: * Pneumatically lowerable drawbar, 2,100 mm long, with 40 mm drawbar eye and height adjustment ----Electrical System / Lighting: * TPMS (tire pressure monitoring system), display option in the truck via EBS signal (without truck-side installation) * LED tail lights 12 / 24 V * 15-pole electrical connector ----General Components: * Tool box made of powder-coated sheet steel * Spare wheel holder in body construction on the right side * Closed side underrun protection * Plastic quarter fenders with splash guards * Plastic rear impact protection buffer * Foldable A-frame sign at the rear ----Loading Area: * Hot-dip galvanized main frame with raised outer frame for guiding roll containers * Sheet steel floor with recesses for rollers in the bogie area * With roll-off container transport, a continuous length of 5,500 - 7,000 mm is possible * Pneumatic 4-way clamp locking system as well as mechanical, plug-in stop angles at the front in the track * Transport of up to 2 skip loaders with a maximum volume of 10 m³ is possible * Including 8 repositionable container stops for lateral centering of the containers, the front 4 container stops are plugged in with pivoting stops * Weld bead as an anti-slip surface in the track area of the loading ramp * Mechanical support legs at the rear ----Load Securing: * 3 pairs of 10-ton UVV lashing rings on the side for attaching tensioning elements for positive and frictional securing of the containers, each with 4 lashing straps in a cloverleaf design (on the side) * 1 pair of 13.4-ton UVV lashing rings at the front * 4 x 8-ton lashing eyes embedded in the outer frame on each side ----Ramps: * Aluminum loading ramps (10.6 tons / pair), 2,800 x 470 mm, suitable for rubber-tired and tracked vehicles (lockable storage compartment from the rear) ----Painting: * Reflective contour striping on the side and rear * Frame hot-dip galvanized * Axles, drawbar painted black ----Information: * Load securing certificate according to DIN 30722-1 * Load securing certificate according to DIN EN 12195-1, DIN EN 12640, DIN EN 12642 and VDI 2700 * --Permissible total weight of 20,000 kg technically possible-- * New vehicle without initial registration with manufacturer's warranty * Errors and prior sale excepted ----Delivery Time: * Available immediately from Egstorf

Condition: new, maximum load weight: 12,200 kg, overall weight: 14,400 kg, axle configuration: 2 axles, Year of construction: 2026, * TM-TA 14.4: ----Brake system: * Wabco EBS braking system * Emergency release device for spring brake cylinders * Drum brakes ----Axles: * 2 x 7 t Gigant axles Nsdpfol Thyqex Adholg ----Suspension: * Parabolic springs with equalizer assembly ----Drawbar / Flange eye: * Height-adjustable, hot-dip galvanized drawbar, +/- 150 mm * 40 mm flange towing eye ----Electrics / Lighting: * 15-pin power connector * LED rear lights * RDÜ tire pressure monitoring system ----General equipment: * Jost landing leg at the front * 2 x external drop-down supports at the rear * Closed plastic single mudguards * Folding A-sign at the rear * Plastic underrun protection buffer * Hot-dip galvanized underrun protection bumper with integrated chain storage box (Dimensions: W= 370 mm x D= 420 mm x H= 480 mm) front left & right ----Load securing: * 2 x 5.3 t UVV lashing rings per side for attaching tensioning devices ----Skip stops: * 2 removable side stops for centering the skips laterally * Front skip stops can be positioned in 4 places with a swiveling stop ----Paintwork: * Hot-dip galvanized chassis * Axles, springs, air reservoir, and landing leg painted in black ----Notes: * Subject to errors and prior sale * New vehicle with manufacturer's warranty ----Delivery time: * Immediately available ex Egestorf

Condition: used, maximum load weight: 12,080 kg, overall weight: 14,400 kg, axle configuration: 2 axles, first registration: 06/2024, loading space length: 3,900 mm, loading space width: 1,920 mm, loading space height: 415 mm, Year of construction: 2022, Equipment: ABS, * ETM-TA 14.4: ----Brakes: * Wabco ABS braking system * Emergency release system for spring brake cylinders * Drum brakes ----Axles: * 2 x 7 t Gigant axles ----Suspension: * Parabolic springs with tandem equalization unit ----Drawbar / Coupling Eye: * Height-adjustable drawbar (+/- 150 mm) * 40 mm bolted coupling eye ----General Attachments: * Jost support winch at the front * Side underride protection * Foldable A-sign at the rear ----Electrics / Lighting: * 15-pin power connector * Multi-chamber tail lights ----Body: * Fixed steel front and side walls * Removable steel rear wall * Floor made of 50 mm softwood * 1 sliding steel plate (750 x 1,000 mm) at the front incl. 2 removable trough stops at the front, insertable in 2 positions * Rear cross member designed for aluminum loading ramps incl. 2 additional drop supports at the rear ----Loading Edge: * Unloaded loading edge approx. 710 mm ----Load Securing: * 4 removable trough stops, can be inserted in 2 positions for lateral centering of troughs * Each side with 1 x (13.5 t) UVV lashing point for securing devices * 2 ratchet tensioners (spindle adjustment) with compensation chain and quick shortener (tension force 6,300 kg) ----Tyres: * Tyre size: 285/70R19.5 ----Wheelbase: * Wheelbase: 1,140 mm ----Paintwork: * Chassis, front wall, side walls, mudguards, drawbar, rear drop supports hot-dip galvanized * Axles, springs, support winch, air tank painted in black ----General Information: * Vehicle has a single-day registration in 06/2024, due to missing tire pressure monitoring system and has not been loaded/used * Subject to errors and prior sale Nodpfx Asl Th Eyjdhelg ----Delivery Time: * Immediately available from Egestorf on the A7

Condition: used, maximum load weight: 12,080 kg, overall weight: 14,400 kg, axle configuration: 2 axles, first registration: 06/2024, loading space length: 3,900 mm, loading space width: 1,920 mm, loading space height: 415 mm, Year of construction: 2022, Equipment: ABS, * ETM-TA 14.4: ----Brakes: * Wabco ABS brake system * Emergency release mechanism for spring-loaded cylinders * Drum brakes ----Axles: * 2 x 7-ton Gigant axles ----Suspension: * Parabolic springs with tandem equalization unit ----Drawbar / Drawbar Eye: * Height-adjustable drawbar (+/- 150 mm) * 40 mm bolt-on drawbar eye ----General Attachments: * Jost landing gear at the front * Side underrun protection * Rear folding A-board ----Electrics / Lighting: * 15-pin power connector * Multi-chamber tail lights ----Body: Nedpfxol Th Dmo Adhelg * Fixed steel front and side walls * Removable steel rear wall * Floor made of 50 mm softwood * 1 sliding plate support 750 x 1,000 mm at the front section including 2 removable skip stops at the front, lockable in 2 positions * Rear traverse for attaching aluminium loading ramps, incl. 2 additional rear drop-down supports ----Loading Edge: * Unloaded loading edge approx. 710 mm ----Load Securing: * 4 removable skip stops, can be locked in 2 positions for side centering of skips * 1 x (13.5 t) UVV lashing point per side for attaching tie-down elements * 2 ratchet tensioners (spindle adjustment) with compensating chain and quick shortener (tensioning force 6,300 kg) ----Tyres: * Tyres: 285/70R19.5 ----Wheelbase: * Wheelbase: 1,140 mm ----Paintwork: * Chassis, front wall, side walls, mudguards, drawbar, rear drop-down supports hot-dip galvanized * Axles, springs, landing gear, and air reservoirs painted in black ----General Info: * Vehicle registered for one day in 06/2024, due to missing tyre pressure monitoring system; never loaded or used * Errors and prior sale excepted ----Delivery Time: * Immediately available ex Egestorf (A7)

Condition: used, maximum load weight: 31,000 kg, overall weight: 40,000 kg, axle configuration: > 3 axles, first registration: 07/2024, loading space length: 9,290 mm, loading space width: 2,520 mm, loading space height: 950 mm, * PT 40.0 Profi ----Brakes: * Wabco EBS-E (electronic braking system) * Emergency release system for spring brake cylinders * Drum brakes ----Axles: * 4 x 11-ton Gigant axles ----Suspension: * Air suspension with lifting and lowering system and rapid drop valve ----Drawbar: * Drawbar with 50 mm drawbar eye and height adjustment ----Lighting / Electrical: * EBS multi-voltage system with 12 & 24 V electrical system * 15-pole power connector * LED lighting system 12 / 24 V * LED rotating beacon (removable) at the rear * 2 LED reversing lights (switched via reverse gear) ----General attachments: * Manometer - pressure gauge for load weight determination (axles separated into 2 air suspension circuits) * Lateral impact guard * Swivel supports at the rear of the chassis frame * Mechanically adjustable warning sign packages at the front and rear * Front plastic quarter fenders with splash protection * Rear straight, galvanized steel splash guards with splash protection * Reflective contour strips on the sides and at the rear * Tool box made of galvanized steel sheet, black powder-coated, approx. 1,000 mm wide, 600 mm deep, 300 mm high ----Low-bed platform: * Extension in front of the turntable platform, approx. 490 mm long with 45° corners * ROBOTER welded anti-slip surface on the steel plate of the turntable platform * Hardwood flooring on the running surfaces of the low-bed platform ----Load securing (La-Si-package consisting of): * 1 x 13.4-ton UVV lashing eye on each side in front of the front bulkhead support * 4 holes on each side in the turntable platform, each with a lashing force of 2 tons * 1 pair of lashing eyes (13.4 tons) hanging at the rear on the left and right in front of the rear crossbeam * 4 pairs of UVV lashing rings (10 tons) on each side, swiveling and lowerable, loadable in all directions and recessed in the outer frame * 3 rung pockets on each side with simultaneous 2-ton lashing option ----Widening package: * Hot-dip galvanized mechanical folding outriggers for 3 m overall width (but not in the rear slope) * Beam holder for widening extensions under the chassis on the left in the longitudinal direction ----Excavator arm rest: * Excavator arm rest above the rear axle up to the end crossbeam, approx. 2,100 mm long and approx. 190 mm deep Nedpol Tlhrefx Adhslg * 2 pairs of 6.4-ton lashing eyes on each side in the excavator arm rest ----Ramps: * Hydraulic, one-piece ramps (approx. 3,000 x 720 mm) mechanically adjustable on the sides * Outer beams of the ramps made of hardwood * Steel construction as preparation for a 6-way control valve ----Loading height: * Loading edge unladen approx. 950 mm +/- 20 mm ----Tires: * Tires 235/75 R 17.5 ----Paint: * Chassis, turntable, folding outriggers, mechanical support legs, ramps hot-dip galvanized * --Axles, air tanks, drawbar painted in a black tone-- ----Info: * Vehicle has a temporary registration in 07/2024, due to a missing tire pressure monitoring system and has not been loaded/used * New vehicle with manufacturer's warranty * Errors and prior sale are subject to change ----Delivery time: * Immediately available from Egestorf

Condition: used, first registration: 06/1998, overall weight: 18,000 kg, empty load weight: 4,200 kg, color: beige, gearing type: other, emission class: none, operating hours: 8,640 h, maximum load weight: 13,800 kg, next inspection (TÜV): 09/2026, suspension: steel, loading space length: 7,100 mm, loading space width: 2,470 mm, tire size: 235/75 R17.5, front tire size: 235/75 R17.5, rear tire size: 235/75 R17.5, driver cabin: other, Equipment: additional headlights, chassis, compressed air brake, fog lights, lighting, truck registration, Müller Mitteltal 2-axle (formerly a container) platform/flatbed trailer TM 2 * SAF axles * Twin tires * Leaf spring suspension * Tires: 235/75 R17.5 * Excellent remaining tread depth * 2 toolboxes on the right * DUO-Matic connection * 50 mm drawbar eye * Side stops for containers * Various lashing points on the sides * Loading height: 1.04 m * Dimensions: L - 7.10 m, W - 2.47 m * Weights: GVWR - 18,000 kg, GAWR - 4,200 kg, Net weight - 13,800 kg * German vehicle with German documents!! * First owner!! * First registration: 19.06.1998 * MOT valid until 09/2026 * Inspection valid until 03/2026 * VIN: WMM00000W0042223 Subject to prior sale, errors and changes! Company logos have been partially removed from the images – please inquire! Functionality of extras without guarantee! Your contact person: Christoph Ott Njdpjzrh E Aefx Adhelg Tel. + WhatsApp:

Condition: used, empty load weight: 4,700 kg, overall weight: 18,000 kg, axle configuration: 2 axles, first registration: 11/2009, next inspection (TÜV): 11/2026, loading space length: 5,000 mm, loading space width: 2,380 mm, loading space height: 980 mm, loading space volume: 12 m³, suspension: air, tire size: 385/65 R22,5, wheelbase: 1,310 mm, color: red, Equipment: ABS, Drum brake EBS (Electronic Braking System) Payload 13,300 kg Steel sideboards Nljdezliu Eopfx Adhog Left side: swing-out and folding, with lifting springs BPW axles Foldable underrun protection Errors and omissions excepted.

Condition: used, maximum load weight: 7,850 kg, overall weight: 11,000 kg, axle configuration: 2 axles, first registration: 08/2010, total length: 8,000 mm, total width: 2,550 mm, total height: 3,500 mm, Errors and prior sales excepted! Internal number: A2. A0053979 – EQUIPMENT - Ex-German Armed Forces - Twin-axle - Loading ramps - Pintle hook (military) - Wooden floor - 11 tons gross vehicle weight Njdpfx Adez Emq Ujhslg - Storage box - Hand-operated spindle brake - UVV lashing rings ... and more ---- The vehicle is in original condition! Nationwide delivery possible for an extra charge. Errors and prior sales excepted. We will gladly accept your vehicle as a trade-in. Financing / leasing also possible without a down payment! Do you have any further questions? We would be happy to advise you!

Condition: new, maximum load weight: 18,900 kg, overall weight: 24,000 kg, axle configuration: 3 axles, loading space length: 7,000 mm, loading space width: 2,480 mm, Year of construction: 2026, * TRA-Kombi 24.0: ----Brakes: * Wabco EBS-E (electronic braking system) * Emergency release device for spring brake cylinders * Drum brakes ----Suspension: * Air suspension with manual lowering at the rear ----Axle: * 3 x 11 t Gigant axles * Center axle liftable ----Drawbar: * Pneumatically lowerable drawbar, 2,100 mm long with 40 mm towing eye and height adjustment system ----Electrics / Lighting: * LED tail lights * 15-pin electrical connector * Tire pressure monitoring system (TPMS) ----General attachments: * Toolbox made of powder-coated steel sheet (W: 1,000 mm x H: 300 mm x D: 450 mm) * Storage box for container nets made of galvanized steel sheet (W: 960 mm x H: 300 mm x D: 450 mm) * Side underrun protection * Plastic quarter mudguards with spray protection * Plastic rear impact protection buffers * Mechanical drop supports at the rear ----Container / Low loader platform: * Hot-dip galvanized main frame with raised outer frame (approx. 25 mm raised) to guide roll containers * Steel floor with roller recesses in the bogie area * Suitable for transport of roll-off containers with lengths from 5,500 to 7,000 mm * Pneumatic 4-point clamp locking and mechanically insertable stop angles at the front in the guide rails * Loading certificate according to DIN 30722-1 * Transport of up to 2 skip containers with a maximum volume of 10 m³ possible * Includes 8 adjustable skip stops for lateral centering; the front 4 stops are inserted with a pendulum stop ----Load securing: * 3 pairs of 10 t UVV lashing rings on the side for attaching tensioning elements for positive and frictional securing of skips * 4 cloverleaf lashing slots on each side and 1 pair of 13.4 t UVV lashing rings facing forward * Load securing certificate according to DIN EN 12195-1, DIN EN 12640, DIN EN 12642, and VDI 2700 ----Ramps: * Weld bead as anti-slip surface in the ramp track area * 1 pair of aluminum approach ramps (16 t / pair) 2,800 x 400 mm, suitable for rubber-tired and tracked vehicles (lockable storage compartment at the rear) ----Tyres: * Tyres: 235/75 R17.5 ----Ride height: * Loaded ride height approx. 1,003 mm ----Payload: Nodopk D Awjpfx Adholg * Payload 18,900 kg ----Paintwork: * Reflective contour tape on sides and rear * Axles, turntable, drawbar, and air tanks painted in black * Hot-dip galvanized main frame ----Information: * Technically permissible gross weight of 27,000 kg * New vehicle without initial registration, with manufacturer's warranty * Errors and prior sale reserved ----Delivery time: * Available from approx. calendar week 47/2026

Condition: new, maximum load weight: 18,900 kg, overall weight: 24,000 kg, axle configuration: 3 axles, loading space length: 7,000 mm, loading space width: 2,480 mm, Year of construction: 2026, * TRA-Kombi 24.0: ----Brakes: * Wabco EBS-E (electronic braking system) * Emergency release device for spring brake cylinders * Drum brakes ----Suspension: * Air suspension with manual lowering at the rear ----Axles: * 3 x 11 t Gigant axles * Centre axle liftable ----Drawbar: * Pneumatically lowerable drawbar, 2,100 mm long, with 40 mm draw eye & height adjustment ----Electrics / Lighting: * LED tail lights * 15-pin electrical connector * TPMS (Tire Pressure Monitoring System) ----General Accessories: * Toolbox made from powder-coated steel (W: 1,000 mm x H: 300 mm x D: 450 mm) * Storage box for container nets made of galvanized steel (W: 960 mm x H: 300 mm x D: 450 mm) * Side underrun protection * Plastic quarter mudguards with spray protection * Plastic rear bumper pads * Mechanical drop-down supports at the rear ----Container / Low Loader Platform: * Hot-dip galvanized main frame with raised outer frame (approx. 25 mm higher) for guiding roll-off containers * Steel floor with roller recesses in the bogie area * For roll-off container transport, container length from 5,500 - 7,000 mm possible * Pneumatic 4-point clamp locking and mechanical pin-in end stops at the front of the rails * Load certification to DIN 30722 - 1 * Transport of up to 2 skip containers with a max. volume of 10 m³ each possible * Includes 8 repositionable skip stops for lateral centring of the skips, front 4 stops with pendulum stops ----Load securing: * 3 pairs of 10 t UVV lashing rings on the sides for hooking in tensioning elements for both positive and non-positive securing of the skips * 4 lashing bars in cloverleaf design (on the sides) and 1 pair of 13.4 t UVV lashing rings to the front * Load securing certificate according to DIN EN 12195-1, DIN EN 12640, DIN EN 12642 and VDI 2700 ----Ramps: Nlodpfx Adepk D Iiehjg * Welded seam as anti-slip surface in the ramp track area * 1 pair of aluminium loading ramps (16 t / pair) 2,800 x 400 mm suitable for rubber-tyred and chain-driven vehicles (lockable storage compartment access from rear) ----Tyres: * Tyres: 235/75 R17.5 ----Ride height: * Loaded ride height approx. 1,003 mm ----Payload: * Payload: 18,900 kg ----Paintwork: * Reflective contour marking tape on the sides & rear * Axles, turntable, drawbar, and air tank painted in black * Hot-dip galvanized main frame ----Information: * Permissible gross weight of 27,000 kg technically possible * New vehicle without first registration, with manufacturer’s warranty * Subject to errors and prior sale ----Delivery time: * Available from approx. CW 47/2026

Condition: used, first registration: 03/2009, overall weight: 40,000 kg, empty load weight: 8,150 kg, color: blue, gearing type: other, emission class: none, maximum load weight: 31,850 kg, next inspection (TÜV): 09/2027, suspension: air, loading space length: 9,800 mm, loading space width: 2,510 mm, tire size: 235/75 R17.5, front tire size: 235/75 R17.5, rear tire size: 235/75 R17.5, driver cabin: other, Equipment: ABS, additional headlights, chassis, compressed air brake, fog lights, lighting, truck registration, Müller-Mitteltal T4 Compact Low-Loader * Swivel eye – 40 mm + 50 mm eyelets * Widens to 3 m, including side beams * Hydraulic ramps, manually adjustable in width * Reversing camera * Drum brakes * 1 revolving beacon at the rear * Air suspension * Twin tires * Gigant axles * ABS + DUO-Matic connections * Plates for overwidth indication at the front and rear * Tires: 235/75 R17.5 * Steel toolbox on platform * Ramp length: 2.90 m * Dimensions: internal: L- 9.80 m, W- 2.55 m * Platform loading height: 1.05 m, rear loading height: 0.85 m * Weights: GVW – 40,000 kg, unladen weight: 8,150 kg, payload: 31,850 kg * German vehicle with German documents!! * 2nd hand!! * First registration: 20.03.2009 * New TÜV (German technical inspection) valid until 09/2027 * New emissions test valid until 03/2027 * VIN: WMM000009052911 Subject to prior sale, errors and changes! Company logos have been partially removed from the images – please inquire! Functionality of extras without guarantee! Nedpoz Dv Iyefx Adhelg Your contact person: Christoph Ott Tel. + WhatsApp:

Condition: used, empty load weight: 3,510 kg, maximum load weight: 10,890 kg, overall weight: 14,400 kg, axle configuration: 2 axles, first registration: 08/2016, next inspection (TÜV): 01/2027, loading space length: 5,000 mm, loading space width: 2,420 mm, suspension: steel, tire size: 385/55R19,5 156J, color: other, gearing type: other, front tire size: 385/55R19,5 156J, rear tire size: 385/55R19,5 156J, driver cabin: other, emission class: none, Equipment: ABS, compressed air brake, Wide tires, combination ramp/tailgate, lashing eyes. Additional cost for ramps: €800. Subject to printing errors, errors and changes. Sample images. More details: ! Njdpjz Azkgofx Adhslg

Condition: new, maximum load weight: 31,630 kg, overall weight: 40,000 kg, axle configuration: > 3 axles, loading space length: 9,250 mm, loading space width: 2,520 mm, Year of construction: 2026, * T 4: * EBS * Emergency release system for spring accumulators * Drum brakes * 4 x 11 to. Gigant axles * Parabolic springs * Mech. axle compensation front and rear * Tire pressure monitoring with display option in the truck via EBS signal - without truck-side installation * Warning sign packages front & rear * Reflective contour striping on the sides and rear * EBS multi-voltage system for 12 & 24 V electrical systems * LED rotating beacon (removable) at the rear * 24 V - 15-pin and additionally 12 V - 7+4 pin power cable * Extended connection cables for agricultural and forestry tractors * LED lighting * Straight drawbar with 40 mm drawbar eye and stepless height adjustment Nlodpfjrczm Dex Adhjg * Toolbox made of powder-coated sheet steel and spare wheel holder in body design, located on the right side * Front, closed, plastic single mudguards * Rear, straight steel mud flaps each with splash protection (spray mist suppression) * Side underrun protection * Extended offset crank extended by 500 mm to the front * Extension of the turntable platform by 520 mm with 45° corners and 3 recessed storage compartments incl. lid and lockable * Chassis made of high-strength fine-grain steel * Floor over the turntable platform made of 50 mm and in the low-bed platform made of 60 mm needle wood * Outer planks of the ramps made of 50 mm bamboo wood * 4 pocket sleeves on each side (but no stanchions present) with simultaneous 2 to. lashing capability * Lasi package consisting of: 2 lashing eyes 6.4 to. at the front left and right on the main frame of the turntable platform, 1 pair of 13.4 to. lashing rings on the outer frame on the front and rear sides, and 4 pairs of 10 to. lashing rings on each side, pivotable and lowerable, loadable in all directions and embedded in the outer frame, 2 pairs of lashing rings 6.4 to. on each side in the excavator arm rest, 8 pairs of galvanized folding outriggers for 3 m total width (but not in the rear slope) * Extension planks stored on the left side in a storage compartment * Excavator arm rest above the rear axle to the end of the approach ramp approx. 2,300 x 740 x 190 mm * Mech. support legs at the rear * Hydr. hot-dip galvanized ramps approx. 3,000 x 720 mm * Hydr. lateral ramp displacement on sliding tube from the ramp shaft * Loading area above the slewing ring: approx. 2,990 x 2,520 mm * Rear loading area: approx. 6,280 x 2,520 mm * Loading height loaded approx. 860 mm (incl. 860 mm approach ramp) * Chassis, turntable, ramps, mech. folding supports at the rear hot-dip galvanized * Axles, springs, air tanks and slewing ring painted in a black tone * New vehicle with manufacturer's warranty * Errors and prior sale reserved * Immediately available from Egestorf

Condition: used, overall weight: 32,000 kg, axle configuration: 2 axles, first registration: 05/2009, total width: 2,550 mm, total height: 3,900 mm, Equipment: ABS, Vehicle identification number: WMM00090053007 Hydraulic drive Tare weight: 7,500 kg DE: Technical inspection due ----LIEBHERR TYPE HTM 1004 - Volume 10 m³ Water: 620 l BPW Eco Plus axles with drum brakes Stetter-Smart-Control LIFT AXLE Tires: 445/65 R 22.5 Changes, prior sale, and errors are expressly reserved. The description serves only for the general identification of the vehicle and does not constitute a guarantee in the legal sense of the term. The description in the purchase contract is the decisive factor. Our offer generally does not include a new TÜV (technical inspection) approval. If a new TÜV approval is desired, we will be happy to provide you with a quote from our partner workshops! The vehicle may be covered with and/or labeled with advertising. Our general terms and conditions of delivery and payment apply. Njdpfxszirhvo Adhjlg

Condition: new, maximum load weight: 27,940 kg, overall weight: 36,000 kg, axle configuration: 3 axles, Year of construction: 2026, * Wabco EBS-E (electronic braking system) * Emergency release device for spring brake cylinders * Drum brakes * 3 x 11 t axles * Air suspension with lift and lower function as well as RtR valve * Traction assistance for shunting, activated on the first axle via EBS – without truck-side installation – with lifted lift axle + 30 mm driving height * Smart-Board infotool mounted on the trailer, equipped with pressure sensors for total axle load display Nlodpfx Aewh Hdxodheg * Last axle as a trailing steering axle with electro-pneumatic steering lock * Locking of the trailing axle activated from the cab for maneuvering purposes via EBS (without truck-side installation) * 2" king pin * 1 liftable axle * Side underrun protection * Front aluminum drop-down supports and rear swivel supports on the chassis * Alcoa LVL One aluminum rims * 15-pin power connector * LED lighting 12 / 24 V * Rear removable LED rotating beacon * 2 additional LED reversing lights * 2 LED work lights mounted laterally on the trailer (without truck-side installation) * 7-pin socket at the rear for oversize load lighting * Side marker lights with indicator control * Tire pressure monitoring system with display capability in the truck via EBS signal (without truck-side installation) * Mechanically adjustable warning sign packages front and rear * Straight steel mudguards * Semi-trailer platform with 45° chamfered front corners and a front toolbox made of galvanized, powder-coated steel sheet (W = 2,480 x H = 500 x L = 665 mm) with top hinged lid and side doors in the chamfered corners * 400 mm high aluminum side walls (RAL 9010 pure white) on the sides of the semi-trailer platform, foldable and removable * Rear panel inserted, height 150 mm * Rear slope on the semi-trailer platform to the low bed, approx. 700 mm long with anti-slip tread plate surface and a perforated strip at the end for hanging on aluminum loading ramps * Semi-trailer platform and low loader platform with 50 mm clamped timber floorboards * Checker plate above the axles * Prepared for 3 slots underneath the semi-trailer platform for storage of optional aluminum loading ramps * Swivel arm as support for connection lines from the truck to the trailer * Load securing package (LaSi): perforated outer frame on the semi-trailer platform with 45° edge and hole pattern for lashing equipment (2 t lashing capacity per point at minimum spacing of 480 mm), each side with 2 x 6.3 t recessed lashing rings in the floor, each side with 1 x 16.5 t lashing ring in the incline from the low loader platform to the semi-trailer platform, 2 pairs of 16.5 t lashing rings in the low loader platform (1 x on the longitudinal beams after the step, 1 x above the center axle beside the longitudinal beam), each side with 3 x 13.4 t lashing rings on the outer frame (1 x at start of the semi-trailer step, 1 x at start of loading ramp slope, 1 x at end of loading ramp slope), each side with 3 x 10 t lashing rings (2 x between front wheel recess and first axle, 1 x between second and third axle), each side with 3 x 5 t lashing rings bolted to the outer frame of the wheel recesses (2 x at front, 1 x at rear wheel recess) * Extended excavator arm trough running from the end of the last fixed axle over the steering axle up to the rear crossmember, with internal reinforcement profile, approx. W = 770 mm x rear D = 270/front D = 170 mm, each side with 2 x 6.4 t lashing rings in the excavator arm trough * Each side with 2 wheel recesses, 390 mm deep and 640 mm wide, f