Used Müller-Mitteltal Work Platform Trailers for sale (262)

Condition: new, maximum load weight: 31,630 kg, overall weight: 40,000 kg, axle configuration: > 3 axles, loading space length: 9,250 mm, loading space width: 2,520 mm, * T 4: * EBS (Electronic Braking System) Cpsdpfxerczm De Aa Rst * Emergency release device for spring brake cylinders * Drum brakes * 4 x 11-ton Gigant axles * Parabolic springs * Mechanical axle equalisation, front and rear * Tire pressure monitoring with in-cab readout via EBS signal – without truck-side installation * Warning panel kits at front and rear * Side and rear contour marking tape, reflective * EBS multi-voltage system for 12 & 24 V electrics * Removable rear LED beacon * 24 V 15-pin power cable and additional 12 V 7+4-pin power cable * Extended connection cables for agricultural and forestry tractors * LED lighting * Straight drawbar with 40 mm towing eye and infinitely adjustable height * Toolbox made of powder-coated sheet steel and spare wheel holder in basket design, right side * Front closed single plastic mudguard * Straight rear steel mudguards with spray suppression * Lateral underrun protection * Offset extension 500 mm forward * Turntable platform extended by 520 mm to front, with 45° corners, 3 recessed lockable storage compartments incl. lids * Chassis made of high-tensile fine-grained steel * Floor above turntable platform: 50 mm softwood; in low-loader platform: 60 mm softwood * Outer planks of ramps made from 50 mm bamboo * 4 stake pockets per side (no stakes included), each with 2-ton lashing capacity * Load securing package consisting of: 2 x 6.4-ton lashing rings at front left/right on main frame of turntable platform, 1 pair 13.4-ton lashing rings each at front and rear external frame, 4 pairs per side 10-ton pivoting and lowering lashing rings, loadable in all directions and embedded in external frame, 2 pairs 6.4-ton lashing rings in excavator arm rest, 8 pairs galvanized folding extensions for 3m total width (not at rear slope) * Side deck boards for width extension stored in left side storage compartment * Excavator arm rest above rear axle to end of approach slope approx. 2,300 x 740 x 190 mm * Mechanical drop-down supports at rear * Hydraulic, hot-dip galvanized ramps approx. 3,000 x 720 mm * Hydraulically lateral ramp shifting on sliding tube from ramp shaft * Loading area over slewing ring: approx. 2,990 x 2,520 mm * Rear loading area: approx. 6,280 x 2,520 mm * Loading height loaded: approx. 860 mm (incl. approach slope) * Chassis, turntable, ramps, rear mechanical support feet hot-dip galvanized * Axles, springs, air tanks, and slewing ring painted in black shade * New vehicle with manufacturer’s warranty * Subject to errors and prior sale * Available from calendar week 46 / 2025

Condition: new, maximum load weight: 23,500 kg, overall weight: 30,000 kg, axle configuration: 3 axles, loading space length: 8,380 mm, loading space width: 2,520 mm, Year of construction: 2024, * PT 30 profile: * EBS (electronic braking system) Cjdpfotplwijx Aa Rspt * Emergency release device for spring-loaded cylinders * Drum brakes * 3 x 11 tonne Gigant axles * Air suspension with lifting and lowering system and RtR valve * Smart board mounted on the trailer as an information tool (for axle load display - front and rear separately) * Tire pressure monitoring with display option in the truck via EBS signal without truck-side installation * Side impact protection * Swivel supports at the rear of the chassis frame * Mechanically adjustable warning sign packages at the front and rear * Front plastic quarter fender with splash guard * Rear straight galvanized. Sheet steel aprons with splash guard * Reflective contour tape on the side and rear * 15-pin power plug * LED lighting 12/24 V * LED rotating beacon (removable) at the rear * Pull scissors 1,200 mm long with 40 mm pull eye and height adjustment via tension spring & turnbuckle * Tool box made of galvanized sheet steel approx. 650 x 300 x 600 mm, black powder-coated on the right side * Box in the bogie for accessories with hinged lid, 2 cont. locks permanently installed (directly after the bogie platform) * ROBOT welded ANTI-SLIP coating on the steel plate of the bogie platform (protruding weld beads) * La-Si package consisting of: 2 lashing eyes (13.4 tonnes) at the front left & right on the bulkhead support, front & rear 1 pair of UVV lashing rings (13.4 to.) and 3 pairs of UVV lashing rings (10 to.) on the side, swiveling and lowerable, loadable in all directions and embedded in the outer frame, 3 stake pockets on the side with simultaneous 2 ton lashing option * 6 pairs of mechanical folding booms for 3 m total width (but not in the rear slope) * Widening planks placed in the middle of the loading area * Hydraulic one-piece loading ramps approx. 3,000 x 720 mm * Mechanically laterally adjustable * 4-way control block for later retrofitting of hydraulic. Ramp shift * Chassis, bogie, folding boom, drop supports and ramps hot-dip galvanized * Axles, slewing ring, air tank, drawbar painted in a black tone * Loading edge when loaded approx. 910 mm +/- 20 mm air suspension, * New vehicle with manufacturer's warranty * Errors and interim purchase subject to reservation * Available for immediate delivery from Egestorf

Condition: new, maximum load weight: 31,000 kg, overall weight: 40,000 kg, axle configuration: > 3 axles, loading space length: 9,290 mm, loading space width: 2,520 mm, loading space height: 950 mm, * PT 40.0 profile: * Wabco EBS-E (electronic braking system) * Emergency release device for spring-loaded cylinders * Drum brakes * 4 x 11 tonne Gigant axles * Air suspension with lifting and lowering system and RtR valve * Manometer pressure indicator for determining load weight (axles separated into 2 air suspension circuits) * Side impact protection * Swivel supports at the rear of the chassis frame * Mechanically adjustable warning sign packages at the front and rear * Front plastic quarter fender with splash guard * Rear straight galvanized. Sheet steel aprons with splash guard Cpsdpjl Tlhrofx Aa Rjt * Reflective contour tape on the side and rear * EBS multi-voltage system with 12 & 24 V electrics * 15-pin power plug * LED lighting system 12 / 24 V * LED rotating beacon (removable) at the rear * 2 LED reversing lights (switched via reverse gear) * Pull scissors with 50 mm pull eye and height adjustment * Tool box made of galvanized sheet steel, black powder-coated, approx. 1,000 mm wide, 600 mm deep, 300 mm high * Front section in front of the bogie platform approx. 490 mm long with 45° corners * ROBOT welded ANTI-SLIP coating for the steel plate of the bogie platform * La-Si package consisting of: in front of the front wall support on the left & right 1 x 13.4 ton each. UVV lashing eye, 4 holes on each side in the bogie platform with a lashing force of 2 tons each, 1 pair of lashing eyes (13.4 tons) hanging at the rear left and right in front of the rear carrier, 4 pairs of UVV lashing rings (10 tons) on each side, can be swiveled and lowered, can be loaded in all directions and embedded in the outer frame, 3 stake pockets on each side with a simultaneous 2 ton lashing option * Hot-dip galvanized mechanical folding boom for a total width of 3 meters (but not in the rear slope) * Plank holder for widening under the chassis on the left in the longitudinal direction * Excavator boom storage above the rear axle to the end carrier approx. 2,100 mm long and approx. 190 mm deep, 2 pairs of 6.4 tons on each side. Lashing rings in the excavator boom storage * Hardwood floor on the running surfaces of the low-loading platform * Hydraulic one-piece ramps (approx. 3,000 x 720 mm) mechanically laterally adjustable * Outer planks of the ramps made of hardwood * Steel construction in preparation for 6-way control slide * Loading edge unloaded approx. 950 mm +/+ 20 mm chassis * Bogie, folding boom, mechanical drop supports, ramps hot-dip galvanized * --Axles, air tank, pull scissors painted in a black tone-- * Tires 235/75 R 17.5 * Vehicle has a daily registration in 07/2024, due to missing tire pressure monitoring system and has not been loaded/used * New vehicle with manufacturer's warranty * Errors and prior sale subject to reservation * Available for immediate delivery from Egestorf

Condition: new, maximum load weight: 16,400 kg, overall weight: 30,000 kg, axle configuration: 3 axles, Year of construction: 2024, * T3 profile 30.0: * EBS-E (electronic braking system) * RDÜ tire pressure monitoring * Emergency release device for spring-loaded cylinders * Drum brakes * 3 x 11 ton BPW Eco axles * Air suspension with lifting and lowering system * SmartBoard as an information tool on the trailer with pressure sensors for pressure display for total axle load display for each axle group * Side impact protection * Mechanically adjustable warning sign packages at the front and rear * Front axle closed. Plastic fenders and rear straight galvanized sheet steel aprons, each with splash guard * Hinged lid (hot-dip galvanized) for the tool box in the bogie platform * Tool box made of galvanized sheet steel approx. 650 x 300 x 600 mm (black powder-coated) on the right side * 15-pin power plug * LED lighting 12 / 24 V * LED rotating beacon (removable) at the rear * Side marker lights with indicator control * Pull scissors with 40 mm pull eye and height adjustment via tension spring & turnbuckle * Tire pressure monitoring system with display option in the truck via EBS signal (without truck-side installation) * Rubber covering on the folding ramps and on the ramp on the left and right (approx. 860 mm long) Cpedpfx Aasq Dyvcj Rjt * Rubber covering on the longitudinal beams from the front to the end beam * Hardwood floor on the running surfaces of the low-loading platform * 4 stake pockets on each side with a simultaneous 2 ton. Lashing option * La-Si package consisting of: 5 pairs of UVV lashing rings that can be swiveled and lowered, can be loaded in all directions and are embedded in the outer frame - 13.4 tons in the corners, otherwise 10 tons * 6 pairs of mechanical folding booms for 3 m total width (but not in the rear slope) * Plank holder under the loading area in the longitudinal direction * Roller stop raised in front of the front beam with 1 x 6.4 ton lashing eye on each side * Hydraulic folding ramps (approx. 4,650 x 720 mm) with hydraulically extendable tip section and load holding valves * Hydraulic lateral ramp shifting * Hydraulic rear support (single-stage cylinder) * Hydraulic. Flow divider in the trailer (with hydraulic pump output in the truck of over 40 liters up to max. 140 liters/min.) * Hydraulic control block splash-proof * Two-line hydraulics * Loading area above the turntable: approx. 1,960 x 2,520 mm, * Rear loading area: approx. 6,500 x 2,520 mm (incl. 860 mm approach slope) * Loading height when loaded approx. 890 mm +/- 20 mm air suspension * Chassis, bogie, roller stop, folding extensions & ramps hot-dip galvanized. * Axles, turntable, pull scissors, air tank etc. painted in a black tone * Loading height when loaded: approx. 890mm +/- 20mm * New vehicle with manufacturer's warranty * Errors and prior sale subject to reservation * Available for immediate delivery from Egestorf

Condition: new, maximum load weight: 14,550 kg, overall weight: 19,000 kg, axle configuration: 2 axles, loading space length: 6,270 mm, loading space width: 2,470 mm, loading space height: 400 mm, Year of construction: 2024, * ETÜ-TA-R 19.0: * Wabco EBS-E (electronic braking system) * RDÜ (tire pressure monitoring) * Emergency release device for spring-loaded cylinders * Drum brakes * 2 x 11 tonnes Gigant axles * Air suspension, drawbar with 50 mm flanged drawbar eye and height-adjustable drawbar Cpedpopk D D Hjfx Aa Rjt * Jost landing gear at the front * External folding supports at the rear * Toolbox made of galvanized sheet steel, approx. 650 x 350 x 320 mm, on the right side (powder-coated in black) * Side impact protection * Plastic quarter fender * 15-pin power connector * LED taillights * Reinforcement package for drilling rig transport on the chassis - loading height + 20 mm * 50 mm clamped softwood floor * Device for retrofitting container locks in front of the bulkhead * Bolted bulkhead made of smooth sheet steel * Trapezoidal profiled sheet steel side walls, foldable with side wall spring jack * Steel rear wall retractable between the ramps - bracket inside in front of the bulkhead when not in use * Bolted rear stanchions * Perforated Outer frame angled at approximately 45 degrees with a 2-ton lashing capacity every 480 mm * Installation of 3-ton drop lashing brackets possible every 600 mm * 1 x 10-ton lashing ring in each of the front and rear corners, various holes in the front and end beams for 1.2-ton lashing capacity * One-piece mechanical Grating loading ramps with spring mechanism for one-person operation, approx. 2,750 x 620 mm (can be collapsed to within 20 mm) * Rear approach slope approx. 860 mm * Chassis, drawbar, bulkhead, tailgate, rear folding supports, and loading ramps hot-dip galvanized * Axles, springs, air chamber, and landing gear painted in a single black tone * Wheelbase: 1,310 mm * Tires: 235/75R17.5 * Side walls painted in RAL 9010 pure white * Side walls painted in a single RAL color available for an additional charge * New vehicle with manufacturer's warranty * Errors and prior sale subject to change * Available for immediate delivery from Egestorf

Condition: new, maximum load weight: 10,750 kg, overall weight: 14,400 kg, axle configuration: 2 axles, loading space length: 7,000 mm, loading space width: 2,470 mm, loading space height: 400 mm, Year of construction: 2025, * ETÜ-TA-R 14.4: * RDÜ tire pressure monitoring * EBS brake system * Emergency release device for spring-loaded cylinders * Drum brakes * 2 x 7 tonnes Gigant axles * Parabolic springs with compensating unit * Drawbar height adjustable by 300 mm - Drawbar extension by 250 mm to 2,250 mm * 15-pin power connector * LED lighting * Front landing gear * External folding supports at the rear * Plastic toolbox approx. 858 x 500 x 500 mm, front right outside on the bulkhead * Side impact protection * Plastic quarter fenders * 50 mm softwood floor * In front of the bulkhead and rear slope, provision for retrofitting container locks for transporting 20" containers Codpfx Aaev Eq Evo Rjpt * Bolted bulkhead made of smooth sheet metal * Trapezoidal sheet steel side walls, foldable, split in the middle once * Steel rear wall can be inserted between the ramp brackets when not in use * Bolted rear stanchions * Perforated outer frame Approx. 45-degree canted with a 2-ton lashing capacity every 480 mm, installation of 3-ton drop lashing rings possible every 600 mm, 1 x 6.3-ton lashing ring in each of the front and rear corners, various holes in the front and end beams for 1.2-ton lashing capacity * One-piece mechanical grating loading ramps with spring mechanism for one-person operation, approx. 2,750 x 600 mm (collapsible up to 20 mm) * Rear approach slope approx. 860 mm chassis * Drawbar, front wall, tailgate, folding supports, and loading ramps hot-dip galvanized * Axles, springs, air chamber, flanged drawbar eye, and landing gear painted in a single black tone -- * Reinforced and certified body according to EN 12642 XL including load securing certificate-- * Wheelbase 1,140 * Side walls painted in black RAL 9010 pure white * Side panels can be painted in a RAL color for an additional charge * New vehicle with manufacturer's warranty * Errors and prior sale subject to change * Available for immediate delivery from Egestorf

Condition: new, maximum load weight: 23,700 kg, overall weight: 30,000 kg, axle configuration: 3 axles, * T3 Profi 30.0: * Wabco EBS-E (electronic braking system) * RDÜ tire pressure monitoring * Emergency release device for spring-loaded cylinders * Drum brakes * 3 x 11 ton BPW Eco axles * Air suspension with manual lowering at the rear * Pressure gauge pressure display for determining the load weight (axles separated into 2 air suspension circuits), * Side impact protection * Swivel supports at the rear of the chassis frame * Mechanically adjustable warning sign packages at the front and rear * Front axle closed. Plastic fenders and rear straight galvanized sheet steel aprons, each with splash guard * Reflective contour tape on the side and rear * Hinged lid (hot-dip galvanized) for the toolbox in the bogie platform * LED tail lights * Rotating beacon (removable) at the rear * Pull scissors with 40 mm pull eye and height adjustment via tension spring & turnbuckle * 2 x 7-pin power plugs * 4 stake pockets on each side with simultaneous 2 ton lashing option * La-Si package consisting of: 2 lashing eyes (6.4 ton) at the front left & right on the main frame of the bogie platform, 5 pairs of UVV lashing rings that can be swiveled and lowered, can be loaded in all directions and are embedded in the outer frame - 13.4 ton in the corners, otherwise 10 ton * 6 pairs of mechanical folding booms for 3 mtr. Total width (but not in the rear slope) * Widening planks placed in the middle of the loading area * hydr. one-piece loading ramps (approx. 3,000 x 720 mm) laterally adjustable * Loading area above the turntable: approx. 1,960 x 2,520 mm * Loading height unloaded approx. 1,070 mm * Rear loading area: approx. 6,500 x 2,520 mm * Loading height unloaded approx. 910 mm (incl. 860 mm approach slope) * Chassis, bogie, drawbar, folding extensions & loading ramps hot-dip galvanized Cjdpfx Asl Tpwysa Rspt * Axles, turntable, air tank etc. painted in a black tone * Tires 235/75 R 17.5 * Payload approx. 24,000 kg with 30,000 kg total weight * New vehicle with manufacturer's warranty * Errors and prior sale subject to change * Available for immediate delivery from Egestorf

Condition: new, maximum load weight: 10,360 kg, overall weight: 14,400 kg, axle configuration: 2 axles, loading space length: 6,270 mm, loading space width: 2,470 mm, loading space height: 400 mm, Year of construction: 2025, * ETÜ-TA-ER 14.4: * RDÜ (tire pressure monitoring with display option in the truck via EBS signal without truck-side installation) * Electronic braking system EBS * Emergency release device for spring-loaded cylinders * Drum brakes * 2 x 5.5 tonnes Gigant axles * Air suspension with lifting and lowering system * Drawbar height adjustable by 300 mm * Jost landing gear at the front * External hot-dip galvanized folding supports at the rear * Plastic toolbox at the front right, outside the bulkhead * Side impact protection * Plastic quarter fenders * LED lighting system * 15-pin power connector * Hot-dip galvanized chassis, drawbar, bulkhead, and rear wall * 50 mm softwood floor * Provision for retrofitting 20" counterlocks at the front and rear * Bolted smooth sheet metal bulkhead Codpepk D Dqjfx Aa Rjpt * Trapezoidal steel sheet sidewalls, foldable with side wall spring jack * Bolted hot-dip galvanized rear stanchions * Perforated outer frame, angled at approximately 45 degrees, with a 2-ton lashing capacity every 480 mm, installation of 3-ton drop lashing brackets every 600 mm possible, 1 x 6.3 ton lashing ring in each of the front and rear corners, various holes in the front and end beams for 1.2 ton lashing options * 1 pair of aluminum loading ramps approx. 3,310 x 400 mm (load capacity 8 tonnes per pair) suitable for rubber-tired and tracked vehicles. Storage compartment recessed into the chassis below the loading area from the rear. * Vehicle hot-dip galvanized * New vehicle with manufacturer's warranty * Errors and prior sale subject to change * Available for immediate delivery from Egestorf

Condition: new, maximum load weight: 14,660 kg, overall weight: 18,000 kg, axle configuration: 2 axles, loading space length: 6,270 mm, loading space width: 2,470 mm, loading space height: 400 mm, Year of construction: 2025, * ETÜ-TA-R 19.0: * Wabco EBS braking system * RDÜ tire pressure monitoring system * Emergency release device for spring brake cylinders * Drum brakes * 2 x 10 t BPW Eco axles * Parabolic springs - 110 mm wide - with tandem compensation unit * Drawbar with 50 mm flange towing eye and height-adjustable drawbar * Jost landing gear at the front * External folding supports at the rear Cpjdpfxjl Th Hwe Aa Rjt * Lateral underrun protection * Plastic quarter mudguards * 15-pin electrical connector * LED tail lights * 50 mm softwood floor * Fixture in front of the bulkhead for retrofitting container locks * Bolted bulkhead made of smooth sheet metal * Trapezoidal-profiled steel side walls, foldable with tailgate spring assist * Rear steel wall, retractable between the ramps – with internal holder at the front bulkhead when not in use * Bolted rear stanchions * Perforated external frame, bent at approximately 45 degrees, with 2 t lashing capacity every 480 mm * Option to install 3 t folding lashing rings every 600 mm * One 10 t lashing ring in each front and rear corner, various holes in the bulkhead and rear cross member for 1.2 t lashing options * One-piece mechanical grating ramps with spring mechanism for single-person operation, approx. 2,750 x 620 mm (retractable to 20 mm) * Ramp gradient at the rear approx. 860 mm * Chassis, drawbar, bulkhead, rear wall, ramps, and folding supports hot-dip galvanized * Side wall coating in RAL 9010 pure white * Other RAL color options for side walls available at extra cost * Axles, springs, air tanks, flange towing eye, and landing gear painted in black * New vehicle with full manufacturer's warranty * Errors and prior sale reserved * Immediately available from Egestorf

Condition: new, maximum load weight: 14,400 kg, overall weight: 19,000 kg, axle configuration: 2 axles, loading space length: 6,270 mm, loading space width: 2,470 mm, loading space height: 400 mm, Year of construction: 2025, * ETÜ-TA-ER 19.0: * WabcoEBS-E (electronic braking system) * RDÜ tire monitoring system * Emergency release device for spring-loaded cylinders * Drum brakes * 2 x 11 t Gigant axles * Air suspension with lift and lowering system * Drawbar with 50 mm flange eyelet and height adjustment of 110 mm via offset plate * Jost landing gear at the front * Outward folding supports at the rear * Plastic toolbox approx. 750 x 350 x 300 mm on the right side * Side underrun protection * Plastic quarter mudguards * 15-pin power plug * Multi-chamber tail lights * Reinforcement package for drill rig transport on the chassis * 50 mm softwood floor in clamped version * Preparation in front of the front wall for subsequent installation of container locks * Bolted front wall made of smooth sheet metal * Split steel side walls - trapezoidal profile - foldable with center folding stanchion * Steel rear wall can be slid in between the ramps - holder for non-use inside in front of the front wall * Rear stakes bolted * Perforated outer frame bent at approx. 45 degrees with 2 t lashing capacity every 480 mm * Installation of 3 t quick-lash rings possible every 600 mm * Lasi package: in the corners at the front and rear each 1 x 10 t UVV lashing ring, on each side 2 x 8 t UVV retractable lashing rings in the outer frame, various holes in the front and end carrier for 1.2 t lashing options Cpedpfx Asmi Tmaja Rst * One-piece slide-in ramps approx. 2,750 x 620 mm * Approach angle at rear approx. 860 mm * Chassis, drawbar, front wall, tailgate, folding supports and drive-on ramps hot-dip galvanized * --- Axles, air tanks, flange eyelet and landing gear painted in a shade of black --- * Loading height unladen approx. 940 mm * Loading height laden approx. 910 mm * Wheelbase: 1,810 mm * Tires: 235/75R17.5 * Vehicle is hot-dip galvanized * New vehicle with manufacturer's warranty * Errors and interim sale excepted * Immediately available from Egestorf

Condition: new, maximum load weight: 14,200 kg, overall weight: 19,000 kg, axle configuration: 2 axles, loading space length: 7,000 mm, loading space width: 2,470 mm, loading space height: 400 mm, Year of construction: 2023, * ETÜ-TA-R 19.0: * Wabco EBS-E (electronic braking system) * Emergency release device for spring-loaded cylinders * Drum brakes * 2 x 11 ton Gigant axles * Air suspension * Drawbar with 50 mm flanged towing eye and height adjustment of 110 mm by offset plate * Jost support winch at the front * External folding supports at the rear * Plastic toolbox approx. 750 x 350 x 300 mm, mounted right side * Side underrun protection * Plastic quarter mudguards * 15-pin power plug * LED lights * Reinforcement package for drilling device transport on the chassis * 50 mm softwood floor in clamped design * Fixture in front of the bulkhead for retrofitting container locks * Bolted bulkhead made of smooth sheet metal * Split side walls made of steel sheet - trapezoidal profiled - folding down with folding stanchion in the middle * Steel rear wall, insertable between the ramps - holder for when not in use located inside in front of the bulkhead * Rear stanchions bolted * Perforated outer frame bent at approx. 45 degrees with 2 ton lashing capacity every 480 mm Cpjdpsl Tp Azsfx Aa Ret * Installation of 3 ton folding lashing brackets possible every 600 mm * Lashing package: in the corners at the front and rear 1 x 10 ton UVV lashing ring each, on each side 2 x 8 ton UVV lashing rings retractable in the outer frame, various holes in the front and end carrier for 1.2 ton lashing possibility * One-piece mechanical grating ramps with spring system for one-man operation, approx. 3,000 x 620 mm (can be pushed together to 20 mm) * Approach slope at the rear approx. 860 mm * Chassis, drawbar, bulkhead, tailgate, folding supports and ramps hot-dip galvanized * Axles, air tanks, flanged towing eye and support winch painted in a shade of black * Loading height unloaded approx. 940 mm * Loading height loaded approx. 910 mm * Wheelbase: 1,810 mm * Tires: 235/75R17.5 * Side walls painted in RAL 9010 pure white * Painting of the side walls in an RAL color for an additional charge possible * Vehicle has a day registration (without use) * Errors and prior sale reserved * Immediately available from Egestorf on the A7

Condition: new, maximum load weight: 10,900 kg, overall weight: 14,400 kg, axle configuration: 2 axles, loading space length: 6,270 mm, loading space width: 2,470 mm, loading space height: 400 mm, Year of construction: 2025, * ETÜ-TA-R 14.4: * RDÜ (Tire Pressure Monitoring) * EBS electronic brake system * Emergency release device for spring brake cylinders * Drum brakes * 2 x 7 t Gigant axles * Air suspension * Tow bar height adjustable by approx. 300 mm - tow bar extension by 250 mm to 2,250 mm * Jost support winch at front * LED rear lights * Exterior hot-dip galvanized folding supports at rear * Plastic toolbox front right outside at the front wall * Side underrun protection * Plastic quarter mudguards * Hot-dip galvanized chassis and tow bar, front wall, rear wall, tailgate, and loading ramps * 50 mm softwood floor * Mounting fixture in front wall for retrofitting container locks * Bolted front wall made of smooth sheet metal * Side walls made of profiled steel sheet - foldable with side wall spring loader * Steel rear wall insertable between ramp holders; when not in use, stored inside at the front wall * Bolted rear stanchions * Perforated outer frame approx. 45 degrees bent with 2 t lashing force every 480 mm, installation of 3 t folding lashing brackets every 600 mm possible, in front and rear corners 1 x 6.3 t lashing ring each, various holes in front and rear cross members for 1.2 t lashing options * One-piece mechanical grid ramp with spring mechanism for one-man operation approx. 2,750 x 600 mm (can be compressed down to 20 mm) * Rear approach angle approx. 860 mm * --Reinforced and certified body according to EN 12642 XL including load securing certificate-- * Side wall color in RAL 9010 pure white * Painting of side walls in other RAL colors possible at extra charge Cpedpfx Aasq Dyvye Rjt * New vehicle with manufacturer warranty * Errors and prior sale reserved * Immediately available from Egestorf

Condition: used, axle configuration: 3 axles, first registration: 09/2001, total length: 10,000 mm, total width: 2,510 mm, suspension: steel, Year of construction: 2001, Additional information : Brand: MÜLLER MITTELTAL Model: T 3 Structure: platform ( platform L=8400 / W=2510 / H=940 mm ) Year: 09.2001 Suspension: steel Brakes: drum Dimensions: L/W: 10000 mm / 2510mm Masses: full/empty: 24000 kg / 6100 kg = More information = Suspension: leaf suspension Cpedpfxsuwvbqe Aa Ret Empty weight: 6.100 kg Carrying capacity: 17.900 kg GVW: 24.000 kg Please contact Andrei Somov, Mark Ševtšenko, Alejandro Goyeneche or Deniss Urmaker for more information

Condition: new, suspension: other, color: other, gearing type: other, driver cabin: other, emission class: none, fuel: biodiesel, Storage compartment for aluminum ramps, price per storage compartment, length approx. 2.48 m, width approx. 1 m, height approx. 27 cm, , --  Misprints, errors and changes reserved, sample images --, More information at: !, More details: ! Cpsdpfexnx Rnjx Aa Rst

Condition: new, maximum load weight: 8,800 kg, overall weight: 11,900 kg, axle configuration: 2 axles, loading space length: 5,370 mm, loading space width: 2,470 mm, loading space height: 400 mm, Year of construction: 2025,

Condition: used, maximum load weight: 29,850 kg, overall weight: 32,000 kg, axle configuration: 2 axles, first registration: 07/2012, next inspection (TÜV): 01/2028, Year of construction: 2012, Internal vehicle number: G300402 German vehicle Immediately available at our premises in Kaufungen – Kassel, Germany Cpedpfxoxy Ul Se Aa Rot For more INFO, contact Luis Lucena Year of manufacture: 2012 Empty trailer weight: 6,530 kg LIEBHERR concrete mixer semi-trailer 10 m³ Errors and omissions excepted We are happy to take your used vehicle in part exchange. Financing available directly with us. GOLEC NUTZFAHRZEUGE GMBH We speak: German, English, Spanish, Polish, Ukrainian, Russian, Bulgarian.

Condition: used, empty load weight: 7,340 kg, maximum load weight: 22,660 kg, overall weight: 30,000 kg, axle configuration: 3 axles, first registration: 05/2012, loading space length: 9,200 mm, suspension: steel, tire size: 235/75 R 17,5, color: other, gearing type: other, front tire size: 235/75 R 17,5, rear tire size: 235/75 R 17,5, driver cabin: other, emission class: none, Equipment: ABS, compressed air brake, Loading area length approx. 9,200 mm, loading height approx. 900 mm, 16 x lashing eyes, , Vehicle is sold on order , , , -- Subject to misprints, errors and alterations, sample pictures --, More data under: !, More Details: ! Cpsdpfjx Rqquox Aa Rjt

Condition: new, maximum load weight: 8,870 kg, overall weight: 11,900 kg, axle configuration: 2 axles, loading space length: 6,270 mm, loading space width: 2,470 mm, loading space height: 400 mm, Year of construction: 2025,

Condition: used, empty load weight: 7,180 kg, maximum load weight: 22,820 kg, overall weight: 30,000 kg, axle configuration: 3 axles, first registration: 02/2018, next inspection (TÜV): 07/2026, loading space length: 9,000 mm, suspension: air, tire size: 235/75R17,5 ---/140J, color: other, gearing type: other, front tire size: 235/75R17,5 ---/140J, rear tire size: 235/75R17,5 ---/140J, driver cabin: other, emission class: none, Equipment: ABS, compressed air brake, Loading area length approx. 9,000 mm, loading height approx. 900 mm, insertable stakes, -- printing errors, mistakes and changes reserved, sample images --, More data at: !, More details: ! Cjdpsx Rqn Hsfx Aa Rept

Condition: new, maximum load weight: 8,780 kg, overall weight: 11,900 kg, axle configuration: 2 axles, loading space length: 5,000 mm, loading space width: 2,420 mm, loading space height: 500 mm, Year of construction: 2024, * KA-TA-R 11.9 Masterline: ----Brakes: * EBS braking system * Emergency release device for spring-loaded cylinders * Drum brakes ----Axle: * 2 x 5.5 t BPW axles ----Suspension: * Parabolic springs with tandem compensating unit ----Drawbar / Flange Eye: * Height-adjustable (up to 300 mm), hot-dip galvanized drawbar with 40 mm flange eye ----General Attachments: * Jost mechanical landing gear at the front * 2 mechanical, hot-dip galvanized folding support legs at the rear * Side-mounted toolbox made of galvanized sheet steel, on the right * Plastic quarter mudguards ----Electrics / Lighting: * RDÜ tire pressure monitoring system * 15-pin power connector * Bolted underrun protection with LED tail lights ----Tipper Body: * Mesh hooks on the sides and rear, integrated into the central locking mounts plus 3 external hooks on the front wall * Hot-dip galvanized chassis * Steel pal. three-way tipper body, fully galvanized * Continuous side walls, without central stanchion, foldable, with drop side spring supports * Tailboard can be folded down and used as a swinging gate, with manual central locking * Hot-dip galvanized, bolted rear stanchion ----Load Securing: * 1 x 5 t recessed, foldable lashing ring in each corner, plus 4 x 3 t recessed and foldable lashing rings integrated in the outer frame on each side * 4 mm steel floor, with slot rail at the rear for loading ramps ----Ramps: * 1 pair of aluminum loading ramps, approx. 3,570 x 400 mm (load capacity 8 t/pair), suitable for rubber-tired and tracked vehicles * Lockable storage compartment under the bed, integrated into the chassis, accessible from the rear ----Tyres: * Tyres 235/75 R 17.5 Cpedpfspk D D Ujx Aa Rjt ----Paintwork: * Axles, springs, air tanks, drawbar and landing gear painted in black * Vehicle is hot-dip galvanized ----Information: * Body reinforced, load securing certificate according to EN 12642 XL * New vehicle with manufacturer warranty * Subject to prior sale and errors ----Delivery time: * Immediately available ex Egestorf on the A7

Condition: used, empty load weight: 4,550 kg, maximum load weight: 13,450 kg, overall weight: 18,000 kg, axle configuration: 2 axles, first registration: 10/2016, loading space length: 6,540 mm, loading space width: 2,480 mm, suspension: air, tire size: 235 / 75 R 17,5, color: beige, gearing type: other, front tire size: 235 / 75 R 17,5, rear tire size: 235 / 75 R 17,5, driver cabin: other, emission class: none, fuel: biodiesel, Equipment: ABS, compressed air brake, 10 pairs of lashing eyes, loading height approx. 900 mm, , customer vehicle, , -- Misprints, errors and omissions excepted, sample pictures --, More data under: !, More Details: ! Cedpex Rqn Tjfx Aa Rjpt

Condition: new, maximum load weight: 8,780 kg, overall weight: 11,900 kg, axle configuration: 2 axles, loading space length: 5,000 mm, loading space width: 2,420 mm, loading space height: 500 mm, Year of construction: 2024, * KA-TA-R 11.9 Masterline: ----Brakes: * EBS braking system * Emergency release device for spring-loaded cylinders * Drum brakes ----Axle: * 2 x 5.5 t BPW axles ----Suspension: * Parabolic springs with tandem compensating unit ----Drawbar / Flange Eye: * Height-adjustable (up to 300 mm), hot-dip galvanized drawbar with 40 mm flange eye ----General Attachments: * Jost mechanical landing gear at the front * 2 mechanical, hot-dip galvanized folding support legs at the rear * Side-mounted toolbox made of galvanized sheet steel, on the right * Plastic quarter mudguards ----Electrics / Lighting: * RDÜ tire pressure monitoring system * 15-pin power connector * Bolted underrun protection with LED tail lights ----Tipper Body: * Mesh hooks on the sides and rear, integrated into the central locking mounts plus 3 external hooks on the front wall * Hot-dip galvanized chassis * Steel pal. three-way tipper body, fully galvanized * Continuous side walls, without central stanchion, foldable, with drop side spring supports * Tailboard can be folded down and used as a swinging gate, with manual central locking * Hot-dip galvanized, bolted rear stanchion ----Load Securing: * 1 x 5 t recessed, foldable lashing ring in each corner, plus 4 x 3 t recessed and foldable lashing rings integrated in the outer frame on each side * 4 mm steel floor, with slot rail at the rear for loading ramps ----Ramps: Codpfx Aaopk D Dmo Ropt * 1 pair of aluminum loading ramps, approx. 3,570 x 400 mm (load capacity 8 t/pair), suitable for rubber-tired and tracked vehicles * Lockable storage compartment under the bed, integrated into the chassis, accessible from the rear ----Tyres: * Tyres 235/75 R 17.5 ----Paintwork: * Axles, springs, air tanks, drawbar and landing gear painted in black * Vehicle is hot-dip galvanized ----Information: * Body reinforced, load securing certificate according to EN 12642 XL * New vehicle with manufacturer warranty * Subject to prior sale and errors ----Delivery time: * Immediately available ex Egestorf on the A7

Condition: used, empty load weight: 2,500 kg, maximum load weight: 7,500 kg, overall weight: 10,000 kg, axle configuration: 2 axles, first registration: 09/2003, loading space length: 5,200 mm, suspension: steel, tire size: 245/70R19,5 140/138J, wheelbase: 990 mm, color: other, gearing type: other, front tire size: 245/70R19,5 140/138J, rear tire size: 245/70R19,5 140/138J, driver cabin: other, emission class: none, Equipment: ABS, compressed air brake, 10 x lashing eyes, 600 mm drop sides, , -- Misprints, errors and omissions excepted, sample pictures --, More data under: !, More Details: ! Cpsdsx N Rtgjpfx Aa Rot

Condition: used, empty load weight: 6,500 kg, maximum load weight: 23,500 kg, overall weight: 30,000 kg, axle configuration: 3 axles, first registration: 06/2010, suspension: steel, tire size: 235 / 75 R 17,5, color: other, gearing type: other, front tire size: 235 / 75 R 17,5, rear tire size: 235 / 75 R 17,5, driver cabin: other, emission class: none, fuel: biodiesel, Equipment: ABS, compressed air brake, Vehicle is sold on behalf of a customer, partly wooden boards def., 17 pairs of lashing eyes, , loading height approx. 900 mm, , -- Misprints, errors and omissions excepted, sample pictures --, More data under: !, More Details: ! Cedox N Rr Aspfx Aa Rspt

Condition: new, suspension: other, color: other, gearing type: other, driver cabin: other, emission class: none, Leveling bracket for low-loader semi-trailer including container closures, price per leveling bracket, , --  Subject to printing errors, mistakes and changes, sample images --, More information at: !, More details: ! Cedpfxexpwh Ij Aa Rept