Used Müller-Mitteltal Open Flatbed Trailers for sale (257)

Condition: new, maximum load weight: 6,870 kg, overall weight: 9,900 kg, axle configuration: 1 axle, Year of construction: 2026, * KWH 9.9 ML: ----Brakes: * EBS braking system * Drum brake * Emergency release device for spring-loaded cylinders ----Axle: * BPW axle ----Suspension: * Parabolic springs ----Drawbar / Flange coupling: * Drawbar with 40 mm bolted coupling (height-adjustable, mm) ----Electrical system / Lighting: * 15-pin power connector * LED lighting * Flashing LED side marker lights * TPMS tire pressure monitoring system ----General components: * Front support jacks * Spring-supported square tube supports at the rear with base plate, safety locking pins for various support heights * Enclosed fenders made of sheet steel with splash guard * Enclosed side impact protection, can be used as an advertising space * Plastic toolbox with base insert (horizontal installation), approx. 500 x 350 x 400 mm Cjdpfx Aaou I Iqrjferi ----Superstructure: * Swivel cable drum superstructure, inner width between the drum arms 1,700 mm, with tensioning closure for securing the drum at the ends of the support arms, and a locking mechanism for the cable drum superstructure and the chassis via a centrally arranged claw lock * Motor-hydraulic drum drive with oil motor * Valves and sliding, rubber-coated drive rollers * Hydraulic speed control and brake for drum drive * Steel drum shaft with 76 mm diameter, with centering and rotatable ends * 1 pair of centering cones made of polyamide, stepped offset ----Chassis: * Chassis made of torsion-resistant square tubes and crossmembers ----Pump unit: * Hydraulic pump unit with Loncin gasoline engine including manual and electric starter * Fuel tank and manual starter * 13 hp with gear pump (150 bar) ----Tires: * 315/80 R 22.5 ----Unladen weight: * 2,690 kg unladen weight ----Painting: * Vehicle is hot-dip galvanized ----Information: * New vehicle with full manufacturer's warranty * Subject to errors and prior sale ----Delivery time: * Available from approximately week 49/2026

Condition: used, maximum load weight: 26,250 kg, overall weight: 36,000 kg, axle configuration: 3 axles, first registration: 06/1998, total length: 1,265 mm, * Müller Mitteltal TS3 3-axle low-loader * First registration: 1998 * 3rd axle with trailing steering * Air suspension * Drum brakes * SAF axles * Wheel recesses at 70 cm * Width extensions from 2.55 m to 3 m * Hydraulic ramps, folding and sliding * Overall length: 12.65 m * Length from kingpin: 12.10 m * Loading length: 9.0 m at 0.85 m * On the gooseneck: 3.50 m at 1.45 m width * Unladen weight: 9,750 kg Crodpfx Aaj Aa E Egsfei * Technical total weight: 47,000 kg * Permissible total weight: 36,000 kg * Payload: 26,250 - 37,250 kg * TÜV (technical inspection): 03/27 * SP (safety inspection): 09/27

Condition: used, empty load weight: 7,800 kg, overall weight: 30,000 kg, axle configuration: 3 axles, first registration: 07/2006, loading space length: 9,100 mm, loading space width: 2,750 mm, suspension: air, tire size: 235/75 R17,5, color: grey, Equipment: ABS, Drum brake Payload 22,200 kg Rubber floor Hydraulic double ramps and hydraulic lateral shift Gigant axles Subject to errors and omissions. Credpfewh Rwvsx Aafsi

Condition: new, maximum load weight: 6,900 kg, overall weight: 9,900 kg, axle configuration: 1 axle, Year of construction: 2026, * KWH 9.9 ML: ----Brakes: * EBS braking system * Drum brake ----Axle: * BPW axle ----Suspension: * Parabolic springs ----Electrical System / Lighting: * TPMS (Tire Pressure Monitoring System) * 15-pin electrical connector * LED lighting * Flashing LED side marker lights ----Drawbar / Flange Coupling: * Drawbar with 40 mm screw coupling (height adjustable in mm) ----General Components: * Front support jack * Spring-supported square tube supports at the rear with base plate, safety locking pins for different support heights * Closed steel sheet mudguards with splash protection * Closed side impact protection, usable as an advertising area * Plastic toolbox with floor insert (horizontal installation), approx. 500 x 350 x 400 mm ----Superstructure: * Swiveling cable drum superstructure, width between the drum arms 1,700 mm, with tensioning closure for securing the drum at the ends of the support arms, as well as a locking mechanism for the cable drum superstructure with the chassis via a centrally arranged claw lock * Motor-hydraulic drum drive with oil motor * Valves and adjustable rubber-coated drive rollers Crsdpfx Aajxyniwefsi * Hydraulic speed controller and brake for drum drive * Steel drum shaft with 76 mm diameter, with centering and rotatable ends * 1 pair of centering cones made of polyamide, stepped arrangement * Preparation of steel structure and hydraulics for retrofitting a separate motor ----Chassis: * Chassis made of torsion-resistant square tubes and cross members ----Hydraulics: * Hydraulic line for supply and return ----Tires: * 315/80 R 22.5 tires ----Painting: * Vehicle is hot-dip galvanized ----Information: * 2,690 kg unladen weight * New vehicle with full manufacturer warranty * Errors and prior sale excepted ----Delivery time: * Available for immediate delivery from Egestorf

Condition: used, empty load weight: 3,680 kg, maximum load weight: 10,720 kg, overall weight: 14,400 kg, axle configuration: 2 axles, first registration: 11/2021, loading space length: 5,000 mm, loading space width: 2,420 mm, suspension: steel, tire size: 385/55R19,5 156J, color: other, gearing type: other, front tire size: 385/55R19,5 156J, rear tire size: 385/55R19,5 156J, driver cabin: other, emission class: none, Equipment: ABS, compressed air brake, AS NEW, wide tyres, TIPPER BODY GALVANIZED, 12 lashing eyes, 600 mm side walls, surcharge for ramps 1,000 €, -- Subject to printing errors, mistakes and changes, sample images --, More data at: !, More details: ! Csdpfs Adq Sgsx Aaferi

Condition: used, axle configuration: 3 axles, first registration: 11/2005, Side-mounted, sliding access ramps (L x W) 3050 x 650 mm, with spring-assisted lifting mechanism. PA1776 Our offer generally does not include a new TÜV (German technical inspection) certificate. If a new TÜV certificate is desired, we will gladly provide you with a quote from our partner workshops! The vehicle may be covered with advertising and/or lettering. Our general terms and conditions of delivery and payment apply. We would be happy to prepare a financing or leasing offer for this vehicle. Crodpfx Asz I Hppsafei Please contact us!

Condition: new, maximum load weight: 30,440 kg, overall weight: 40,000 kg, axle configuration: > 3 axles, Year of construction: 2026, Equipment: ABS, T 4 Profi 40.0 ----Brakes: * Wabco EBS-E (electronic braking system) * Emergency release system for spring-loaded cylinders * Drum brakes ----Axles: * 4 x 11-ton Gigant axles ----Suspension: * Air suspension with lifting and lowering system and RtR valve ----Drawbar: * Straight drawbar with 50 mm drawbar eye and stepless height adjustment ----Electrical System / Lighting: * Tire pressure monitoring system with display option in the truck display via EBS signal - without truck-side installation - * SmartBoard as an information tool with pressure sensors for axle load display per axle group * 15-pin power connector * LED rear lights * LED marker lights (removable) at the rear ----General Components: * Warning sign packages at the front & rear * 2 x toolboxes made of galvanized, powder-coated steel sheet, approx. 650 x 300 x 600 mm, on the right side * Closed plastic fender at the front * Straight steel mudguards at the rear, each with splash protection (spray mist suppression) * Lateral impact protection ----Low-bed Platform: * Extension of the turntable platform by 520 mm with 45° corners and 3 recessed storage compartments incl. lids and locking mechanism * Floor over the turntable platform made of 50 mm needlewood, and in the low-bed platform made of 60 mm needlewood * Rubber coating 20 mm instead of wooden floor in the running area with a low-bed length of 6,780 mm including the access ramp * Rubber coating on the access ramp, left and right, approx. 860 mm long * 4 lashing eye pockets on each side (however, no lashing bars included) with simultaneous 2-ton lashing capability Codpjylfvgjfx Aafjri ----Chassis: * Chassis made of high-strength fine-grain steel ----Load Securing (Lasi - Package): Turntable Platform: * 2 pairs of 13.4-ton lashing eyes in the outer frame of the turntable platform Low-bed: * 4 pairs of 10-ton lashing eyes on each side of the outer frame, retractable and loadable in all directions * 2 pairs of 13.4-ton swiveling lashing eyes on each side at the rear ----Ramps: * Rubber coating on the folding access ramps * Hydraulic folding ramps with hydraulic extendable front section, approx. 4,650 x 720 mm * Hydraulic lateral ramp adjustment & load holding valves ----Rear Support: * Hydraulic rear support ----Width Extension: * 8 pairs of galvanized folding outriggers for 3 m overall width (however, not in the rear slope) * Width extension boards stored in a compartment on the left side ----Excavator Arm Rest: * Excavator arm rest above the rear axle to the end of the access ramp, approx. L=2,100 mm x W=740 x D=190 mm * 2 pairs of 6.4-ton lashing eyes on the side in the excavator arm rest ----Hydraulics: * Hydraulic flow divider in the trailer (with hydraulic pump output in the truck of over 40 - max. 120 l/min.) ----Loading Dimensions: * Rear loading area: approx. 6,780 x 2,520 mm (incl. 860 mm access ramp) * Loading area above the turntable: approx. 2,990 x 2,520 mm ----Loading Height: * approx. 890 mm, +/- 20 mm ----Painting: * Reflective contour striping on the sides and at the rear * Chassis, turntable, access ramps, and folding outriggers hot-dip galvanized * Axles, drawbar, air tanks, and turntable painted in a black color ----Information: * New vehicle with manufacturer's warranty * Subject to errors and prior sale ----Delivery Time: * Immediately available from Egestorf

Condition: new, maximum load weight: 30,440 kg, overall weight: 40,000 kg, axle configuration: > 3 axles, Year of construction: 2026, Equipment: ABS, T 4 Profi 40.0 ----Brakes: * Wabco EBS-E (electronic braking system) * Emergency release system for spring brake cylinders * Drum brakes ----Axles: * 4 x 11 ton Gigant axles ----Suspension: * Air suspension with lifting and lowering system and rapid release valve (RtR valve) ----Drawbar: * Straight drawbar with 50 mm drawbar eye and stepless height adjustment ----Electrical System / Lighting: * Tire pressure monitoring system with display option in the truck display via EBS signal - without truck-side installation - * SmartBoard as an information tool with pressure sensors for axle load display per axle group * 15-pole power connector * LED tail lights * Detachable LED marker lights at the rear Crjdpjylfvmjfx Aafoi ----General Components: * Warning sign packages at the front and rear * 2 x toolboxes made of galvanized, powder-coated sheet steel, approx. 650 x 300 x 600 mm, on the right side * Closed plastic fender at the front * Straight steel splash guards at the rear, each with a spray guard (spray mist reduction) * Side impact protection ----Lowboy Platform: * Extension of the turntable platform by 520 mm with 45° corners and 3 recessed storage compartments incl. cover and lockable * Floor over the turntable platform made of 50 mm and in the lowboy platform made of 60 mm hardwood * 20 mm rubber coating instead of wooden floor in the running track area with a lowbed length of 6,780 mm including the ramp * Rubber coating on the ramp on the left and right sides, approx. 860 mm long * 4 lashing eye sockets on each side (but no lashing bars included) with simultaneous 2-ton lashing capability ----Chassis: * Chassis made of high-strength fine-grain steel ----Load Securing (Lasi Package): Turntable Platform: * 2 pairs of 13.4-ton lashing eyes in the outer frame of the turntable platform Lowbed: * 4 pairs of 10-ton lashing rings on each side in the outer frame, retractable and loadable in all directions * 2 pairs of 13.4-ton swiveling lashing rings at the rear on each side ----Ramps: * Rubber coating on the folding ramps * Hydraulic folding ramps with hydraulically extendable front section, approx. 4,650 x 720 mm * Hydraulic side ramp adjustment & load holding valves ----Rear Support: * Hydraulic rear support ----Widening: * 8 pairs of galvanized folding outriggers for a total width of 3 m (but not in the rear ramp) * Widening boards stored on the left side in a storage compartment ----Excavator Arm Rest: * Excavator arm rest above the rear axle to the end of the ramp, approx. L = 2,100 mm x W = 740 x D = 190 mm * 2 pairs of 6.4-ton lashing rings on the side in the excavator arm rest ----Hydraulics: * Hydraulic flow divider in the trailer (with hydraulic pump output in the truck of over 40 - max. 120 liters/min.) ----Loading Dimensions: * Rear loading area: approx. 6,780 x 2,520 mm (incl. 860 mm ramp) * Loading area over the turntable: approx. 2,990 x 2,520 mm ----Loading Height: * approx. 890 mm, +/- 20 mm ----Painting: * Reflective contour strip on the side and rear, * Chassis, turntable, ramps, and folding outriggers hot-dip galvanized * Axles, drawbar, air tanks, and turntable painted in a black tone ----Information: * New vehicle with manufacturer's warranty * Errors and prior sales are subject to change ----Delivery Time: * Immediately available from Egestorf

Condition: new, maximum load weight: 23,700 kg, overall weight: 30,000 kg, axle configuration: 3 axles, Year of construction: 2026, T3 Profi 30.0: ----Brakes: * Wabco EBS-E (electronic braking system) * Emergency release system for spring brake cylinders * Drum brakes ----Axles: * 3 x 11 to BPW Eco axles ----Suspension: * Air suspension with raising and lowering function, controlled by an RtR valve ----Drawbar: * Drawbar with 40 mm drawbar eye and height adjustment via tension spring & locking mechanism ----Electrical system / Lighting: * TPMS tire pressure monitoring system * Smart-Board as an information tool * LED tail lights 12/24 V * Rotating beacon (removable) at the rear * 15-pin power connector ----General components: * Lateral underrun protection * Swivel supports at the rear on the chassis frame * Mechanically adjustable warning sign packages at the front and rear * Front axle: closed plastic fenders, rear axle: straight, galvanized steel mudguards, each with splash protection * Reflective contour strips on the sides and rear * Folding cover (hot-dip galvanized) for the tool box in the turntable platform ----Low-bed platform: * 4 lashing points on each side with simultaneous 2 to lashing capacity * 6 pairs of mechanical folding outriggers for a total width of 3 m (but not in the rear slope) * Extension boards stored in the center of the loading area * Hydraulic, one-piece ramps (approx. 3,000 x 720 mm) adjustable on the sides ----Load securing (La-Si package): * 2 lashing points (6.4 to) at the front left & right on the main frame of the turntable platform * 5 pairs of UVV lashing rings, swiveling and lowering, loadable in all directions and embedded in the outer frame - in the corners 13.4 to, otherwise 10 to. ----Excavator arm rest: * Over the rear axle up to the end crossmember, approx. 2,100 mm long (2 pairs of 6.4 to lashing rings on the sides in the excavator arm rest) ----Loading area: * Over the turntable: approx. 1,960 x 2,520 mm * Rear loading area: approx. 6,500 x 2,520 mm (incl. 860 mm approach slope) ----Loading height: * Unloaded approx. 1,070 mm * Loaded approx. 910 mm ----Tires: * 235/75 R 17.5 ----Paint finish: * Chassis, turntable, drawbar, folding extensions & ramps hot-dip galvanized * Axles, turntable, air tank, etc. painted in a black shade Crjdol Tpwyjpfx Aafoi ----Information: * New vehicle with manufacturer's warranty * Errors and prior sale excepted ----Delivery time: * Available for immediate delivery from Egestorf, near the A7 motorway

Condition: new, maximum load weight: 23,700 kg, overall weight: 30,000 kg, axle configuration: 3 axles, Year of construction: 2026, T3 Profi 30.0: ----Brakes: * Wabco EBS-E (electronic braking system) * Emergency release system for spring brake cylinders * Drum brakes ----Axles: * 3 x 11 to BPW Eco axles ----Suspension: * Air suspension with raising and lowering function, controlled by an RtR valve ----Drawbar: * Drawbar with 40 mm drawbar eye and height adjustment via tension spring & locking mechanism ----Electrical system / Lighting: * TPMS tire pressure monitoring system * Smart-Board as an information tool * LED tail lights 12/24 V * Rotating beacon (removable) at the rear * 15-pin power connector ----General components: * Lateral underrun protection * Swivel supports at the rear on the chassis frame * Mechanically adjustable warning sign packages at the front and rear * Front axle: closed plastic fenders, rear axle: straight, galvanized steel mudguards, each with splash protection * Reflective contour strips on the sides and rear * Folding cover (hot-dip galvanized) for the tool box in the turntable platform ----Low-bed platform: * 4 lashing points on each side with simultaneous 2 to lashing capacity * 6 pairs of mechanical folding outriggers for a total width of 3 m (but not in the rear slope) Crjdpel Tq Euofx Aafei * Extension boards stored in the center of the loading area * Hydraulic, one-piece ramps (approx. 3,000 x 720 mm) adjustable on the sides ----Load securing (La-Si package): * 2 lashing points (6.4 to) at the front left & right on the main frame of the turntable platform * 5 pairs of UVV lashing rings, swiveling and lowering, loadable in all directions and embedded in the outer frame - in the corners 13.4 to, otherwise 10 to. ----Excavator arm rest: * Over the rear axle up to the end crossmember, approx. 2,100 mm long (2 pairs of 6.4 to lashing rings on the sides in the excavator arm rest) ----Loading area: * Over the turntable: approx. 1,960 x 2,520 mm * Rear loading area: approx. 6,500 x 2,520 mm (incl. 860 mm approach slope) ----Loading height: * Unloaded approx. 1,070 mm * Loaded approx. 910 mm ----Tires: * 235/75 R 17.5 ----Paint finish: * Chassis, turntable, drawbar, folding extensions & ramps hot-dip galvanized * Axles, turntable, air tank, etc. painted in a black shade ----Information: * New vehicle with manufacturer's warranty * Errors and prior sale excepted ----Delivery time: * Available for immediate delivery from Egestorf, near the A7 motorway

Condition: used, maximum load weight: 36,750 kg, overall weight: 48,000 kg, axle configuration: 3 axles, first registration: 04/2014, next inspection (TÜV): 10/2027, loading space length: 11,500 mm, loading space height: 900 mm, total length: 12,600 mm, total width: 2,550 mm, Total weight: 46,000 kg / 48,000 kg Unladen weight: 11,250 kg Payload: 34,750 kg / 36,750 kg Codpfx Ae Agq A Dsafjri Overall length: 12,600 - 14,600 mm Loading length: Total approx. 11,500 mm / approx. 8,300 mm low-bed / approx. 3,200 mm gooseneck Width: 2,550 mm - 3,000 mm Loading height: approx. 900 mm Further information: - 2 m telescopic extension - Wheel recesses - Inserts for wheel recesses under the loading platform - Excavator arm recess - Container locking system - Follower axle - Air suspension - 3 m widening - Hydraulic ramps, split, with rubber surface - Rotating beacon - Warning signs - Foldable side panels, gooseneck, 400 mm - Stake pockets - Large lashing kit - Support legs at the rear, foldable - Twin tires

Condition: used, maximum load weight: 31,000 kg, overall weight: 40,000 kg, axle configuration: > 3 axles, first registration: 07/2024, loading space length: 9,290 mm, loading space width: 2,520 mm, loading space height: 950 mm, * PT 40.0 Profi ----Brakes: * Wabco EBS-E (electronic braking system) * Emergency release system for spring brake cylinders * Drum brakes ----Axles: * 4 x 11-ton Gigant axles ----Suspension: * Air suspension with lifting and lowering system and rapid drop valve ----Drawbar: * Drawbar with 50 mm drawbar eye and height adjustment ----Lighting / Electrical: * EBS multi-voltage system with 12 & 24 V electrical system * 15-pole power connector * LED lighting system 12 / 24 V * LED rotating beacon (removable) at the rear * 2 LED reversing lights (switched via reverse gear) ----General attachments: * Manometer - pressure gauge for load weight determination (axles separated into 2 air suspension circuits) * Lateral impact guard * Swivel supports at the rear of the chassis frame * Mechanically adjustable warning sign packages at the front and rear * Front plastic quarter fenders with splash protection * Rear straight, galvanized steel splash guards with splash protection * Reflective contour strips on the sides and at the rear * Tool box made of galvanized steel sheet, black powder-coated, approx. 1,000 mm wide, 600 mm deep, 300 mm high ----Low-bed platform: * Extension in front of the turntable platform, approx. 490 mm long with 45° corners * ROBOTER welded anti-slip surface on the steel plate of the turntable platform * Hardwood flooring on the running surfaces of the low-bed platform ----Load securing (La-Si-package consisting of): * 1 x 13.4-ton UVV lashing eye on each side in front of the front bulkhead support * 4 holes on each side in the turntable platform, each with a lashing force of 2 tons * 1 pair of lashing eyes (13.4 tons) hanging at the rear on the left and right in front of the rear crossbeam * 4 pairs of UVV lashing rings (10 tons) on each side, swiveling and lowerable, loadable in all directions and recessed in the outer frame * 3 rung pockets on each side with simultaneous 2-ton lashing option ----Widening package: * Hot-dip galvanized mechanical folding outriggers for 3 m overall width (but not in the rear slope) * Beam holder for widening extensions under the chassis on the left in the longitudinal direction ----Excavator arm rest: * Excavator arm rest above the rear axle up to the end crossbeam, approx. 2,100 mm long and approx. 190 mm deep * 2 pairs of 6.4-ton lashing eyes on each side in the excavator arm rest ----Ramps: * Hydraulic, one-piece ramps (approx. 3,000 x 720 mm) mechanically adjustable on the sides * Outer beams of the ramps made of hardwood * Steel construction as preparation for a 6-way control valve ----Loading height: Cedpfx Aol Tlhroaferi * Loading edge unladen approx. 950 mm +/- 20 mm ----Tires: * Tires 235/75 R 17.5 ----Paint: * Chassis, turntable, folding outriggers, mechanical support legs, ramps hot-dip galvanized * --Axles, air tanks, drawbar painted in a black tone-- ----Info: * Vehicle has a temporary registration in 07/2024, due to a missing tire pressure monitoring system and has not been loaded/used * New vehicle with manufacturer's warranty * Errors and prior sale are subject to change ----Delivery time: * Immediately available from Egestorf

Condition: new, maximum load weight: 17,650 kg, overall weight: 24,000 kg, axle configuration: 3 axles, loading space length: 9,230 mm, loading space width: 2,480 mm, Year of construction: 2026, * TP 30.0 with 3 cable cradles ----Brakes: * Wabco TEBS (electronic braking system) * Emergency release system for spring brake cylinders * Drum brakes ----Axles: Cjdpfox Nlkgex Aafori * 3 x 11-ton Gigant axles ----Suspension: * Air suspension 17.5" with lifting and lowering system ----Drawbar: * Drawbar, 1,800 mm long, with 40 mm drawbar eye ----Electrical System / Lighting: * Tire pressure monitoring system with display option on the truck display via EBS signal - without installation on the truck side * 15-pole power connector * 2 additional LED reversing lights (switched via reverse gear) * LED lighting ----General Components: * Aluminum air tank * Stainless steel tool box, approx. 1,000 x 300 x 600 mm, on the side * Side underrun protection * Plastic quarter fenders * Underrun protection ----Platform: * Lashing-fix outer frame, 45° angled, with hole pattern for lashing means, lashing force per lashing point 2,000 kg at a distance of 480 mm * Installation of 3,000 kg drop-side brackets possible at a distance of approx. 600 mm - the scope of delivery includes 12 pieces of 3,000 kg lashing brackets on each side * 5 sockets on each side for 100 x 50 mm tubes in the outer frame - the tubes are not included in the scope of delivery * 30 mm screen-printed floor ----Cable Cradles: * 3 galvanized cable cradles secured via continuous locking mechanisms, with side fork pockets, center to center 800 mm (width of the pockets 185 mm) * Drum diameter max. 2,600 mm and drum width max. 1,800 mm * Clear width between the support arms approx. 1,824 mm, with cross connection * 6,000 kg drum weight per cable cradle * Without drive and drum brake * Support arm with tension lock for securing the drum shaft * Steel drum shaft, 76 mm diameter, with centering and rotatable ends * 2 spacer rings * 2 centering cones made of polyamide with 2 handles * 4 pieces of 3.2 ton lashing eyes on the support arms for customer-side securing of the drum against rotation and unwinding ----Loading Height: * Approx. 1,040 mm under load ----Painting: * Chassis, bogie, drawbar, outer frame, underrun protection hot-dip galvanized * Axles painted in a black tone ----Information: * Increasing the permissible total weight to 30 tons is technically possible * New vehicle with manufacturer's warranty * Errors and prior sale excepted ----Delivery Time: * Available from approx. week 51/2026

Condition: new, maximum load weight: 8,600 kg, overall weight: 11,900 kg, axle configuration: 2 axles, loading space length: 5,000 mm, loading space width: 2,420 mm, loading space height: 500 mm, Year of construction: 2026, * KA-TA-R 11.9 Masterline: ----Brakes: * Wabco EBS * Emergency release system for spring brake cylinders * Drum brakes ----Axle: * 2 x 5.5 ton BPW axles ----Suspension: * Parabolic springs with tandem equalizer ----Drawbar / Flange coupling: * Height-adjustable, hot-dip galvanized drawbar by 300 mm with a 40 mm flange coupling ----Electrical system / Lighting: * TPMS tire pressure monitoring system * LED lighting * 15-pole electrical connector ----General components: * Tool box made of galvanized sheet steel on the right side * Bolted underrun protection * Plastic quarter fenders * Jost mechanical front support legs * 2 mechanical, hot-dip galvanized folding support legs at the rear ----Tipping bridge: * Net hooks on the side and at the rear in the bearings of the central locking system, as well as 3 pieces on the outside of the front wall * Hot-dip galvanized chassis * Steel 3-sided tipping body * Continuous side walls without a center rail, foldable with side board spring supports * Folding tailgate and pivoting over a manual central locking system * Hot-dip galvanized, bolted rear rail * 4 mm steel sheet floor * Mounting rail at the rear for loading ramps ----Load securing: * 1 x 5 ton recessed and foldable lashing points in each corner * As well as 4 x 3 ton lashing points on each side, recessed in the outer frame and foldable ----Ramps: Cjdjv Dz N Aspfx Aaferi * 1 pair of aluminum loading ramps approx. 3,310 x 400 mm (load capacity 8 tons / pair) suitable for vehicles with rubber tires and tracked vehicles * Lockable storage compartment at the rear under the loading area, integrated into the chassis ----Tires: * Tires 235/75 R 17.5 ----Painting: * Axles, springs, air tanks, drawbar and support legs painted in a black tone * Side board painted in RAL 9010 pure white * Painting of the side walls in an RAL color possible at an extra charge * Floor and front wall hot-dip galvanized ----Information: * Body reinforced with load securing certificate according to EN 12642 XL * New vehicle with manufacturer's warranty * Errors and prior sale reserved ----Delivery time: * Available from approximately week 45/2026

Condition: new, maximum load weight: 23,830 kg, overall weight: 30,000 kg, axle configuration: 3 axles, loading space length: 8,460 mm, loading space width: 2,520 mm, Year of construction: 2026, * T3 Profile 30.0: ----Brakes: * EBS braking system * Emergency release system for spring brake cylinders * Drum brakes ----Axles: * 3 x 11-ton BPW Eco axles ----Suspension: * Parabolic springs ----Drawbar: * Drawbar with 40 mm drawbar eye and height adjustment via tension spring & locking mechanism ----Electrical system / Lighting: * TPMS tire pressure monitoring system * Multi-voltage system * LED tail lights * Rotating beacon (removable) at the rear * 15-pin power connector ----General attachments: * Mechanical axle compensation at the rear * Side impact protection * Swivel supports at the rear on the chassis frame * Mechanically adjustable warning sign packages at the front and rear * Front mudguards made of molded plastic, and straight, galvanized steel splash guards at the rear, each with splash protection * Reflective contour strip on the sides and at the rear ----Low-loader platform: * Folding cover (hot-dip galvanized) for the tool compartment in the turntable platform * 4 lashing points on each side (but no lashing bars included) with simultaneous lashing option * 6 pairs of mechanical folding outriggers for a total width of 3 m (but not on the rear slope) * Extension boards stored in the center of the loading area ----Load securing (LaSi package): * 2 lashing points (6.4 tons) at the front left & right on the main frame of the turntable platform * 5 pairs of UVV lashing rings, swivel and lowerable, loadable in all directions and recessed in the outer frame - 13.4 tons in the corners, otherwise 10 tons ----Excavator arm rest: * Excavator arm rest over the rear axle up to the end beam, approx. 2,100 mm long (2 pairs of 6.4-ton lashing points on the side in the excavator arm rest) ----Ramps: * Hydraulically operated, one-piece ramps (approx. 3,000 x 720 mm) * Hydraulic side ramp shifting ----Loading area: * over the turntable: approx. 1,960 x 2,520 mm * rear loading area: approx. 6,500 x 2,520 mm (including 860 mm approach angle) ----Loading height: * unladen approx. 910 mm ----Tires: Codpfxox Ipbge Aafori * 235/75 R 17.5 twin tires ----Paint finish: * Chassis, turntable, drawbar and ramps hot-dip galvanized * Axles, springs, air tanks, etc. painted in a black hue * Vehicle is hot-dip galvanized ----Information: * --technically possible gross vehicle weight of 30,000 kg-- * New vehicle with manufacturer's warranty * Errors and prior sale reserved ----Delivery time: * Available for immediate delivery from Egestorf

Condition: new, maximum load weight: 23,830 kg, overall weight: 30,000 kg, axle configuration: 3 axles, loading space length: 8,460 mm, loading space width: 2,520 mm, Year of construction: 2026, * T3 Profile 30.0: ----Brakes: * EBS braking system * Emergency release system for spring brake cylinders * Drum brakes ----Axles: * 3 x 11-ton BPW Eco axles ----Suspension: * Parabolic springs ----Drawbar: * Drawbar with 40 mm drawbar eye and height adjustment via coil spring and tension lock ----Electrical System / Lighting: * TPMS (tire pressure monitoring system) * Multi-voltage system * LED taillights * Rotating beacon (removable) at the rear * 15-pin power connector ----General Components: * Mechanical axle equalization at the rear * Side underrun protection * Swivel supports at the rear on the chassis frame * Mechanically adjustable warning sign packages at the front and rear * Front mudguards made of molded plastic and straight, galvanized steel splash guards at the rear, each with splash protection * Reflective contour tape on the sides and rear ----Low-Loader Platform: * Folding cover (hot-dip galvanized) for the tool compartment in the turntable platform * 4 lashing points on each side (but no lashing bars included) with simultaneous lashing capability * 6 pairs of mechanical folding outriggers for a total width of 3 m (but not in the rear slope) * Extension planks stored in the center of the loading area ----Load Securing (LaSi Package): * 2 lashing eyes (6.4 tons) at the front left and right on the main frame of the turntable platform * 5 pairs of UVV lashing rings, swiveling and lowerable, loadable in all directions and embedded in the outer frame - 13.4 tons in the corners, otherwise 10 tons ----Excavator Arm Rest: * Excavator arm rest extending over the rear axle to the end carrier, approx. 2,100 mm long (2 pairs of 6.4-ton lashing rings on each side in the excavator arm rest) ----Ramps: * Hydraulically operated, one-piece ramps (approx. 3,000 x 720 mm) Credpfjx Ipb Hox Aafei * Hydraulic side ramp adjustment ----Loading Area: * Over the turntable: approx. 1,960 x 2,520 mm * Rear loading area: approx. 6,500 x 2,520 mm (including 860 mm approach slope) ----Loading Height: * Unladen: approx. 910 mm ----Tires: * 235/75 R 17.5 twin tires ----Paintwork: * Chassis, turntable, drawbar and ramps hot-dip galvanized * Axles, springs, air tanks, etc. painted in a black shade * Vehicle is hot-dip galvanized ----Information: * --Technically, a maximum permissible total weight of 30,000 kg is possible-- * New vehicle with manufacturer's warranty * Errors and prior sale excepted ----Delivery Time: * Available for immediate delivery from Egestorf

Condition: used, overall weight: 13,500 kg, axle configuration: 2 axles, first registration: 02/2018, loading space length: 5,060 mm, loading space width: 2,420 mm, loading space height: 500 mm, Year of construction: 2018, MUELLER MITTELTAL Anhänger ( KIPPER ) 5,06 m Imported / Accident-FREE IN VERY GOOD CONDITION! ? YEAR OF PRODUCTION: 2018 AIRSUSPENSION TIRE SIZE: 385/55R19,5 WHEELBASE: 115 PLATFORM: 506 x 242 x 50 m TOTAL WEIGHT: 13 500 kg CAPACITY: 10 000 kg TEL: KUBA - POLSKI, ENGLISH, DEUTSCH, ITALIANO SEBASTIAN - POLSKI, DEUTSCH, ITALIANO, ????? LASZLO - MAGYAR COSTEL - ROMÂN? (Romana facem toate formalitatile pt export inclusiv nr) RADEK - ????? Cedpfsy E Ecnsx Aafjri

Condition: used, maximum load weight: 31,000 kg, overall weight: 40,000 kg, axle configuration: > 3 axles, first registration: 07/2024, loading space length: 9,290 mm, loading space width: 2,520 mm, loading space height: 950 mm, * PT 40.0 Profi Crodpfjl Tnu Aex Aafei ----Brakes: * Wabco EBS-E (electronic braking system) * Emergency release system for spring brake cylinders * Drum brakes ----Axles: * 4 x 11 to. Gigant axles ----Suspension: * Air suspension with lifting and lowering system and rapid lowering valve ----Drawbar: * Drawbar with 50 mm drawbar eye and height adjustment ----Lighting / Electrical: * EBS multi-voltage system with 12 & 24 V electrical system * 15-pin electrical connector * LED lighting system 12 / 24 V * LED rotating beacon (removable) at the rear * 2 LED reversing lights (switched via reverse gear) ----General components: * Pressure gauge - pressure indicator for determining payload (axles separated into 2 air suspension circuits) * Side underrun protection * Swivel supports at the rear of the chassis frame * Mech. adjustable warning sign packages at the front and rear * Front plastic quarter fenders with splash guard * Rear straight, galvanized steel side skirts with splash guard * Reflective contour strip on the side and rear * Tool box made of galvanized steel sheet, black powder-coated, approx. 1,000 mm wide, 600 mm deep, 300 mm high ----Low-loader platform: * Extension in front of the turntable platform approx. 490 mm long with 45° corners * ROBOTER welded anti-slip coating on the steel plate of the turntable platform * Hardwood flooring on the running surfaces of the low-loader platform ----Load securing (La-Si package consisting of): * 1 x 13.4 to. UVV lashing eye to the left and right in front of the front bulkhead beam * 4 holes on each side in the turntable platform, each with a lashing force of 2 to. * 1 pair of lashing eyes (13.4 to.) hanging at the rear left and right in front of the rear beam * 4 pairs of UVV lashing rings (10 to.) on each side, swiveling and lowering, capable of withstanding loads in all directions and recessed in the outer frame * 3 rung pockets on each side with simultaneous 2 to. lashing option ----Widening package: * Hot-dip galvanized mech. folding outriggers for 3 m overall width (however, not in the rear slope) * Beam holder for widening under the chassis on the left in the longitudinal direction ----Excavator arm rest: * Excavator arm rest above the rear axle up to the end beam approx. 2,100 mm long and approx. 190 mm deep * 2 pairs of 6.4 to. lashing eyes on each side in the excavator arm rest ----Ramps: * Hydr. one-piece access ramps (approx. 3,000 x 720 mm) mech. adjustable on the side * Outer planks of the access ramps made of hardwood * Steel structure as preparation for a 6-way control valve ----Loading height: * Unladen loading edge approx. 950 mm +/+ 20 mm ----Tires: * Tires 235/75 R 17.5 ----Paintwork: * Chassis, turntable, folding outriggers, mech. support legs, access ramps hot-dip galvanized * Axles, air tank, drawbar painted in a black tone ----Information: * Vehicle has a day registration in 07/2024, due to the missing tire pressure monitoring system and has not been loaded/used * New vehicle with manufacturer's warranty * Errors and prior sale reserved ----Delivery time: * Available for immediate delivery from Egestorf

Condition: used, overall weight: 32,000 kg, axle configuration: 2 axles, first registration: 05/2009, total width: 2,550 mm, total height: 3,900 mm, Equipment: ABS, Vehicle identification number: WMM00090053007 Cedpfx Ajzirhvjafjri Hydraulic drive Unladen weight: 7,500 kg DE: next inspection due ----LIEBHERR TYPE HTM 1004 - Volume 10 m³ Water: 620 l BPW Eco Plus axles with drum brakes Stetter-Smart-Control LIFTING AXLE Tires: 445/65 R 22.5 Overall height: approx. 3,900 mm Changes, prior sale and errors expressly reserved. The description serves for the general identification of the vehicle and does not constitute a guarantee in the legal sense. The description in the purchase contract is decisive. Our offer generally does not include a new TÜV inspection. If a new TÜV inspection is desired, we will gladly provide you with an offer from our partner workshops! The vehicle may be covered with and/or labeled with advertising. Our general terms and conditions of delivery and payment apply.

Condition: new, maximum load weight: 8,900 kg, overall weight: 11,900 kg, axle configuration: 2 axles, loading space length: 6,270 mm, loading space width: 2,470 mm, Year of construction: 2026, * ETÜ-TA-ER 14.4 Platform: ----Brakes: * EBS (electronic braking system) * Emergency release system for spring brake cylinders * Drum brakes ----Axles: * 2 x 5.5 ton BPW axles ----Suspension: * Air suspension with lifting and lowering system ----Drawbar / Flange drawbar: * Height-adjustable drawbar by 300 mm * Drawbar shortened by approx. 200 mm to approx. 1,800 mm (resulting in a B-dimension of approx. 8,080 mm) * 40 mm flange drawbar ---- Electrical system / Lighting: * 15-pin power connector * LED lighting system 12 / 24 V * 2 LED reversing lights additional at the rear (switched via reverse gear) * 1 LED rotating beacon (removable incl. bracket) at the rear * TPMS (Tire Pressure Monitoring System) ----General components: Cjdpfey U A Elsx Aaferi * Mechanically adjustable 3 m warning sign package at the front and rear * Support winch at the front * Outboard folding supports at the rear * Plastic toolboxes approx. 750 x 350 x 300 mm each on the left & right sides * Side impact protection * Underrun protection * Plastic quarter fenders ----Loading area: * 400 mm high bolted front wall * 50 mm hardwood floor, * 2 pairs of container locking mechanisms (extendable to 3 m container outer width) and lockable, locking dimension when retracted according to ISO - DIN 15190 = 2,259 mm. Container locking mechanisms extended = 2,819 mm (this dimension is not according to DIN) with an absolute outer width of 3,000 mm ----Load securing: * Perforated outer frame approx. 45 degrees angled with 2 ton lashing force every 480 mm * Installation of 3 ton lashing eyelets every 600 mm possible - 5 x 3 ton UVV lashing eyelets installed on each side - * In the corners at the front and rear, each 1 x 6.3 ton lashing point (at the front directly behind the container locking mechanisms in the wooden floor and at the rear in the end beam) * Various drillings in the front and end beam for 1.2 ton lashing ----Ramps: * 1 pair of aluminum insert ramps approx. 3,310 x 410 mm (load capacity 8 tons / pair) suitable for rubber-tired and tracked vehicles * Storage compartment at the rear, recessed under the loading area in the chassis ----Painting: * ---Chassis, drawbar, front wall, underrun protection and rear supports hot-dip galvanized--- * Axles, air tank, support winch at the front and flange drawbar painted in a black tone ----Information: * New vehicle with manufacturer's warranty * Errors and prior sale are subject to change * Sample images ----Delivery time: * Available from approx. week 50/2026

Condition: new, maximum load weight: 17,650 kg, overall weight: 24,000 kg, axle configuration: 3 axles, loading space length: 9,230 mm, loading space width: 2,480 mm, Year of construction: 2026, * TP 30.0 with 3 cable supports ----Brakes: * Wabco TEBS (electronic braking system) * Emergency release device for spring brake cylinders * Drum brakes ----Axle: * 3 x 11-ton Gigant axles ----Suspension: * Air suspension 17.5" with lifting and lowering system ----Drawbar: * Drawbar 1,800 mm long with 40 mm drawbar eye ----Electrical system / Lighting: * Tire pressure monitoring with display option in the truck display via EBS signal - without truck-side installation * 15-pole power connector * 2 additional LED reversing lights (switched via reverse gear) * LED lighting ----General attachments: * Aluminum air tank * Stainless steel tool box, side-mounted, approx. 1,000 x 300 x 600 mm * Side underrun protection * Plastic quarter fenders * Underrun guard Csdpfxjx Nli Ns Aafsri ----Platform: * Lashing ring external frame, 45° angled, with hole pattern for lashing means, lashing force per lashing point 2,000 kg at a distance of 480 mm * Installation of 3,000 kg lashing eyes possible at a distance of approx. 600 mm - the scope of delivery includes 12 pieces of 3,000 kg lashing eyes on each side * 5 pockets on each side for pipe racks 100 x 50 mm in the external frame - the pipe racks are not included in the scope of delivery * 30 mm screen-printed floor ----Drum supports: * 3 pieces of galvanized drum supports, secured via continuous locking mechanisms, with side forklift pockets, center to center 800 mm (width of the pockets 185 mm) * Drum diameter max. 2,600 mm and drum width max. 1,800 mm * Clear width between the support arms approx. 1,824 mm, with cross connection * 6,000 kg drum weight per cable support * Without drive and drum brake * Support arm with tensioning lock for securing the drum shaft * Steel drum shaft, 76 mm diameter, with centering and rotatable ends * 2 spacer rings * 2 centering cones made of polyamide with 2 handle loops * 4 pieces of 3.2-ton lashing eyes on the support arms for securing the drum against rotation and unwinding on the customer side ----Loading height: * Loaded approx. 1,040 mm ----Painting: * Chassis, bogie, drawbar, external frame, underrun guard hot-dip galvanized * Axles painted in a black tone ----Information: * Increase to 30 tons gross vehicle weight technically possible * New vehicle with manufacturer's warranty * Errors and prior sale subject to change ----Delivery time: * Available from week 51/2026

Condition: new, maximum load weight: 17,650 kg, overall weight: 24,000 kg, axle configuration: 3 axles, loading space length: 9,230 mm, loading space width: 2,480 mm, Year of construction: 2026, * TP 30.0 with 3 cable reels ----Brakes: * Wabco TEBS (electronic braking system) * Emergency release device for spring accumulators * Drum brakes ----Axle: * 3 x 11 ton Gigant axles ----Suspension: * Air suspension 17.5" with lifting and lowering system ----Drawbar: * Drawbar, 1,800 mm long, with 40 mm drawbar eye ----Electrical system / Lighting: * Tire pressure monitoring with display option in the truck display via EBS signal - without truck-side installation * 15-pole power plug * 2 additional LED reversing lights (switched via reverse gear) * LED lighting ----General components: * Aluminum air reservoir * Stainless steel toolbox on the side, approx. 1,000 x 300 x 600 mm * Side impact protection * Plastic quarter fender * Underrun protection ----Platform: * Zurr-fix outer frame, 45° angled, with hole pattern for lashing straps, lashing force per lashing point 2,000 kg at a distance of 480 mm * Installation of 3,000 kg drop-side brackets possible at a distance of approx. 600 mm - the scope of supply includes 12 pieces of 3,000 kg lashing brackets on each side * 5 slots for tube supports 100 x 50 mm on each side in the outer frame - the supports are not included in the scope of supply * 30 mm screen-printed floor Cedpsx Nlkajfx Aaferi ----Cable reel supports: * 3 galvanized cable reel supports secured by container locks, with side forklift pockets, center to center 800 mm (width of the pockets 185 mm) * Reel diameter max. 2,600 mm and reel width max. 1,800 mm * Clear width between the support arms approx. 1,824 mm, with cross connection * 6,000 kg reel weight per cable reel support * Without drive and drum brake * Support arm with clamping device for securing the reel shaft * Steel reel shaft, 76 mm diameter, with centering and rotatable ends * 2 spacing rings * 2 centering cones made of polyamide * 4 pieces of 3.2 ton lashing rings on the support arms for customer-side securing of the reel against rotation and unwinding ----Loading height: * loaded approx. 1,040 mm ----Painting: * Chassis, bogie, drawbar, outer frame, underrun protection hot-dip galvanized * Axles painted in a black tone * TP 30.0 with 3 cable reels

Condition: used, empty load weight: 5,300 kg, maximum load weight: 18,700 kg, overall weight: 24,000 kg, axle configuration: 3 axles, first registration: 11/2014, loading space length: 9,400 mm, suspension: steel, tire size: 205/65R17,5, color: other, gearing type: other, front tire size: 205/65R17,5, rear tire size: 205/65R17,5, driver cabin: other, emission class: none, Equipment: ABS, compressed air brake, Loading height approx. 900 mm, loading area length approx. 9,400 mm, tie-down points. -- Subject to printing errors, errors and changes. Sample images. -- More data available at: !, More details: ! Crodpfxj Agt E Ij Aafji

Condition: used, maximum load weight: 12,080 kg, overall weight: 14,400 kg, axle configuration: 2 axles, first registration: 06/2024, loading space length: 3,900 mm, loading space width: 1,920 mm, loading space height: 415 mm, Year of construction: 2022, Equipment: ABS, * ETM-TA 14.4: ----Brakes: * Wabco ABS braking system * Emergency release system for spring brake cylinders * Drum brakes ----Axles: * 2 x 7 t Gigant axles ----Suspension: * Parabolic springs with tandem equalization unit ----Drawbar / Coupling Eye: * Height-adjustable drawbar (+/- 150 mm) * 40 mm bolted coupling eye ----General Attachments: * Jost support winch at the front * Side underride protection * Foldable A-sign at the rear ----Electrics / Lighting: * 15-pin power connector * Multi-chamber tail lights ----Body: * Fixed steel front and side walls * Removable steel rear wall * Floor made of 50 mm softwood * 1 sliding steel plate (750 x 1,000 mm) at the front incl. 2 removable trough stops at the front, insertable in 2 positions * Rear cross member designed for aluminum loading ramps incl. 2 additional drop supports at the rear ----Loading Edge: * Unloaded loading edge approx. 710 mm ----Load Securing: * 4 removable trough stops, can be inserted in 2 positions for lateral centering of troughs * Each side with 1 x (13.5 t) UVV lashing point for securing devices * 2 ratchet tensioners (spindle adjustment) with compensation chain and quick shortener (tension force 6,300 kg) ----Tyres: Credpfx Aael Th Eyofji * Tyre size: 285/70R19.5 ----Wheelbase: * Wheelbase: 1,140 mm ----Paintwork: * Chassis, front wall, side walls, mudguards, drawbar, rear drop supports hot-dip galvanized * Axles, springs, support winch, air tank painted in black ----General Information: * Vehicle has a single-day registration in 06/2024, due to missing tire pressure monitoring system and has not been loaded/used * Subject to errors and prior sale ----Delivery Time: * Immediately available from Egestorf on the A7

Condition: used, maximum load weight: 12,080 kg, overall weight: 14,400 kg, axle configuration: 2 axles, first registration: 06/2024, loading space length: 3,900 mm, loading space width: 1,920 mm, loading space height: 415 mm, Year of construction: 2022, Equipment: ABS, * ETM-TA 14.4: ----Brakes: * Wabco ABS brake system * Emergency release mechanism for spring-loaded cylinders * Drum brakes ----Axles: * 2 x 7-ton Gigant axles ----Suspension: * Parabolic springs with tandem equalization unit ----Drawbar / Drawbar Eye: * Height-adjustable drawbar (+/- 150 mm) * 40 mm bolt-on drawbar eye ----General Attachments: * Jost landing gear at the front * Side underrun protection * Rear folding A-board ----Electrics / Lighting: * 15-pin power connector * Multi-chamber tail lights ----Body: * Fixed steel front and side walls * Removable steel rear wall * Floor made of 50 mm softwood * 1 sliding plate support 750 x 1,000 mm at the front section including 2 removable skip stops at the front, lockable in 2 positions * Rear traverse for attaching aluminium loading ramps, incl. 2 additional rear drop-down supports ----Loading Edge: * Unloaded loading edge approx. 710 mm ----Load Securing: * 4 removable skip stops, can be locked in 2 positions for side centering of skips * 1 x (13.5 t) UVV lashing point per side for attaching tie-down elements * 2 ratchet tensioners (spindle adjustment) with compensating chain and quick shortener (tensioning force 6,300 kg) ----Tyres: * Tyres: 285/70R19.5 Cedpfxsl Th Dmo Aafsri ----Wheelbase: * Wheelbase: 1,140 mm ----Paintwork: * Chassis, front wall, side walls, mudguards, drawbar, rear drop-down supports hot-dip galvanized * Axles, springs, landing gear, and air reservoirs painted in black ----General Info: * Vehicle registered for one day in 06/2024, due to missing tyre pressure monitoring system; never loaded or used * Errors and prior sale excepted ----Delivery Time: * Immediately available ex Egestorf (A7)