Used Müller-Mitteltal Low Loader / Lowbed Trailers for sale (255)

Condition: new, maximum load weight: 23,830 kg, overall weight: 30,000 kg, axle configuration: 3 axles, loading space length: 8,460 mm, loading space width: 2,520 mm, Year of construction: 2026, * T3 Profile 30.0: ----Brakes: * EBS braking system * Emergency release system for spring brake cylinders * Drum brakes ----Axles: * 3 x 11-ton BPW Eco axles ----Suspension: * Parabolic springs ----Drawbar: * Drawbar with 40 mm drawbar eye and height adjustment via coil spring and tension lock ----Electrical System / Lighting: * TPMS (tire pressure monitoring system) * Multi-voltage system * LED taillights * Rotating beacon (removable) at the rear * 15-pin power connector ----General Components: * Mechanical axle equalization at the rear * Side underrun protection * Swivel supports at the rear on the chassis frame * Mechanically adjustable warning sign packages at the front and rear * Front mudguards made of molded plastic and straight, galvanized steel splash guards at the rear, each with splash protection * Reflective contour tape on the sides and rear ----Low-Loader Platform: * Folding cover (hot-dip galvanized) for the tool compartment in the turntable platform * 4 lashing points on each side (but no lashing bars included) with simultaneous lashing capability * 6 pairs of mechanical folding outriggers for a total width of 3 m (but not in the rear slope) * Extension planks stored in the center of the loading area ----Load Securing (LaSi Package): * 2 lashing eyes (6.4 tons) at the front left and right on the main frame of the turntable platform * 5 pairs of UVV lashing rings, swiveling and lowerable, loadable in all directions and embedded in the outer frame - 13.4 tons in the corners, otherwise 10 tons ----Excavator Arm Rest: * Excavator arm rest extending over the rear axle to the end carrier, approx. 2,100 mm long (2 pairs of 6.4-ton lashing rings on each side in the excavator arm rest) ----Ramps: Ledpfx Adox Ipb Hjhsrt * Hydraulically operated, one-piece ramps (approx. 3,000 x 720 mm) * Hydraulic side ramp adjustment ----Loading Area: * Over the turntable: approx. 1,960 x 2,520 mm * Rear loading area: approx. 6,500 x 2,520 mm (including 860 mm approach slope) ----Loading Height: * Unladen: approx. 910 mm ----Tires: * 235/75 R 17.5 twin tires ----Paintwork: * Chassis, turntable, drawbar and ramps hot-dip galvanized * Axles, springs, air tanks, etc. painted in a black shade * Vehicle is hot-dip galvanized ----Information: * --Technically, a maximum permissible total weight of 30,000 kg is possible-- * New vehicle with manufacturer's warranty * Errors and prior sale excepted ----Delivery Time: * Available for immediate delivery from Egestorf

Condition: new, maximum load weight: 10,360 kg, overall weight: 14,400 kg, axle configuration: 2 axles, loading space length: 6,270 mm, loading space width: 2,470 mm, loading space height: 400 mm, Year of construction: 2025, * ETÜ-TA-ER 14.4: ----Brakes: * Electronic braking system (EBS) * Emergency release device for spring-loaded cylinders * Drum brakes ----Axles: * GIGANT axles ----Suspension: * Air suspension with lift and lowering system ----Drawbar / Flange drawbar eye: * Height-adjustable drawbar (adjustable by 300 mm) * 40 mm flange drawbar eye ----Electrics / Lighting: * TPMS (Tire Pressure Monitoring System with display option in the truck via EBS signal—no truck-side installation required) * LED lighting system * 15-pin power connector ----General attachments: * Jost landing gear at the front * Externally mounted, hot-dip galvanized folding support legs at the rear * Plastic toolbox mounted on the front wall, right-hand side * Side underrun protection * Plastic quarter mudguards ----Lowbed platform: * 50 mm softwood floor * Preparation for subsequent installation of 20" container locks at the front and rear * Bolted front wall, smooth sheet steel * Drop sides made of trapezoidal-profile sheet steel, foldable with sideboard spring assist * Bolted, hot-dip galvanized rear stakes ----Load securing: * Perforated outer frame, approx. 45° angled, with 2 t lashing capacity every 480 mm * Option to fit 3 t folding lashing rings every 600 mm * One 6.3 t lashing point at each front and rear corner Lredpspk D Dqefx Adhot * Various holes in the front wall and end crossmember for 1.2 t lashing options ----Ramps: * 1 pair of aluminum loading ramps approx. 3,310 x 400 mm (load capacity 8 t per pair), suitable for rubber-tired and tracked vehicles; storage compartment underneath the loading platform integrated in the chassis for rear access ----Paintwork: * Chassis, drawbar, front wall, and rear wall hot-dip galvanized * Entire vehicle hot-dip galvanized ----Info: * New vehicle with manufacturer's warranty * Errors and prior sale excepted ----Delivery time: * Immediately available ex Egestorf

Condition: used, maximum load weight: 13,700 kg, overall weight: 18,000 kg, axle configuration: 2 axles, first registration: 03/2026, next inspection (TÜV): 03/2027, loading space length: 7,000 mm, loading space width: 2,480 mm, Year of construction: 2026, * TRA 18.0: Lsdpfxszihcpj Adhsrt * 2 in 1 = suitable for roll-off containers and as a low-loader ----Brakes: * EBS electronic braking system * Emergency release device for spring brake cylinders * Drum brakes ----Axles: * 2 x 10-ton Gigant axles ----Suspension: * Air suspension with lifting and lowering system and RTR valve ----Drawbar: * Curved drawbar 2,000 mm long with pivoting drawbar eye 40 / 50 mm (without 8° eye) * GHD height adjustment device instead of drawbar spring ----Electrical System / Lighting: * Tire pressure monitoring with display option in the truck via EBS signal - without truck-side installation - * LED tail lights 12 / 24 V * 15-pole power socket ----General Components: * Toolbox made of powder-coated steel sheet approx. 1,000 x 300 x 600 mm * Spare wheel holder on the right side * Reflective contour strip on the side and rear * Side impact protection * Plastic quarter fenders with splash guard * Plastic impact protection buffer at the rear * Folding A-frame sign at the rear ----Loading Platform: * Main frame with raised outer frames to guide the roll-off containers * Steel sheet floor with recesses for rollers in the bogie area * Continuous length of 5,500 - 7,000 mm possible * Pneumatic 4-point clamp locking system and mech. plug-in stop angles at the front in the track, load securing certificate according to DIN 30722 - 1 * Welded bead as anti-slip surface in the track area of the ramp * Mech. rear support legs ----Load Securing: * 1 pair of 10-ton UVV lashing rings at the front on the end wall cross member * 3 pairs of 10-ton UVV lashing rings on the side in the outer frame * 4 x 2-ton lashing eyes in cloverleaf design on each side * 4 x 8-ton lashing brackets recessed in the outer frame ----Ramps: * 1 pair of aluminum loading ramps (10.6 tons / pair) 2,800 x 470 mm suitable for rubber-tired and tracked vehicles (lockable storage compartment from the rear) ----Painting: * Chassis, bogie, locking parts, rear support legs hot-dip galvanized * but the drawbar, axles, air tank painted in a black tone ----Information: * Vehicle has full manufacturer warranty until 03.2027 * Errors and prior sale excepted * The trailer is in new condition and has only been used a maximum of 5 times ----Delivery Time: * Available for immediate delivery from Egestorf on the A7

Condition: new, maximum load weight: 14,550 kg, overall weight: 18,000 kg, axle configuration: 2 axles, loading space length: 7,000 mm, Year of construction: 2026, RA-T 18.0: Loadable from the front and rear ----Brakes: * Wabco EBS-E (electronic braking system) * Emergency release system for spring brake cylinders * Disc brakes 19.5" * Automatic braking when the transverse locking units are opened ----Axles: * 2 x 10-ton BPW wide-track axles ----Suspension: * Air suspension (automatic lowering when the brake is released) ----Electrical system / Lighting: * Tire pressure monitoring system with display option in the truck via EBS signal – without truck-side installation * 15-pin power connector * LED lighting system with protective cover * 2 LED reversing lights (switched via reverse gear) ----Drawbar: * Pneumatically lowerable drawbar, 1,800 mm long, with 40 mm drawbar eye and height adjustment via tension spring & locking clamp ----General components: * Plastic tool box 858 x 500 x 500 mm on the right side * Storage box for container nets made of galvanized perforated sheet metal, 1,000 x 500 x 500 mm on the side * Closed plastic wheel arches, front and rear * Closed side impact protection (RAL 9010 pure white) as an advertising area * Underrun protection at the rear * Plastic impact protection buffer at the rear * Foldable A-frame sign * Hazardous goods sign with accompanying document pocket and reflective parking warning sign at the rear ----Container area: * Loading possible from the front with lowering of the roller track at the rear and plug-in stops * Roller recesses in the area of the swivel ring with mechanically adjustable stop angles (2 positions) at the front left and right on the roller tracks * Roller track length approx. 6,830 mm * Pneumatic 4-point clamping lock * For the transport of external roll-off containers according to DIN 30722 Part 1 - Dekra load securing certificate available ----Loading height: * When loaded, approx. 1,130 mm ----Painting: * Chassis and locking parts hot-dip galvanized * Air tank, axles, swivel ring and drawbar painted in a black tone ----Information: * --Technically possible gross vehicle weight of 20,000 kg-- * New vehicle without initial registration with manufacturer's warranty * Errors and prior sale excepted * Sample images ----Delivery time: Lsdpjl Tn U Rsfx Adhsrt * Available for immediate delivery from Egestorf

Condition: new, maximum load weight: 8,850 kg, overall weight: 11,900 kg, axle configuration: 2 axles, loading space length: 5,000 mm, loading space width: 2,420 mm, loading space height: 500 mm, Year of construction: 2024, * KA-TA-R 11.9 'Masterline' ----Brakes: * EBS braking system * Emergency release device for spring brake cylinders * Drum brakes ----Axles: * 2 x 5.5 t BPW axles ----Suspension: * Parabolic springs with tandem equalizing unit ----Drawbar / Flange Eye: * Height-adjustable drawbar (approx. 300 mm adjustment) with 40 mm flange towing eye ----General Attachments: * Jost mechanical landing leg at the front * Two mechanical, hot-dip galvanized rear folding support legs * Plastic toolbox approx. 750 x 350 x 300 mm, mounted on the right side * Bolted underrun protection * Plastic quarter mudguards ----Electrics / Lighting: * 15-pin power connector * LED lighting * RDÜ tire pressure monitoring system ----Tipper Body: * Net hooks on sides and rear in the central locking bearings as well as 2 on the front wall * Steel pallet 3-way tipper body (continuous side walls, without center posts), foldable with drop side spring assistors * Rear corner posts bolted * Combination rear steel swing doors, double-leaf, asymmetrically split, can be swung and locked at 270° (not foldable), plus additional swinging frame for automatic tailgate opening during tipping; locking via galvanized rotary bar lock and central locking system * Deactivation function for the automatic tailgate feature when reversing with an open swing door * 4 mm steel floor plate * Rear ramp mounting rail ----Load Securing: * 1 x 5 t lashing ring in each corner * 4 x 3 t recessed lashing eyes in the outer frame on each side ----Ramps: * 1 pair aluminum drive-on ramps, approx. 3,310 x 400 mm (capacity 8 t/pair), suitable for rubber-tired and tracked vehicles * Lockable storage compartment for ramps, mounted under the load area, integrated into the chassis ----Painting: * Drawbar, front wall, tipper body, rear posts, underrun protection, and mechanical support legs, hot-dip galvanized * Side walls and tailgate painted in RAL 9010 pure white * Side wall paint finish in a RAL color of your choice available at extra cost * Axles, springs, flange towing eye, air tank, and landing leg painted in black ----Additional Information: * Reinforced body with EN 12642 XL load securing certificate Ledpfel Thyxox Adhsrt * New vehicle, never registered, with manufacturer's warranty * Subject to errors and prior sale ----Availability: * Available immediately from Egestorf on the A7

Condition: new, maximum load weight: 37,390 kg, overall weight: 48,000 kg, axle configuration: 3 axles, Year of construction: 2026, * TS 3 RM ML 30.0: Lrjdpfx Adetpta Dshet ----Brakes: * Wabco EBS-E (electronic braking system) * Emergency release device for spring brake cylinders * Drum brakes ----Axles: * 3 x 11 t BPW axles * Start-up aid for shunting purposes on the first axle, activated via EBS (no truck-side installation required) * Rear axle as trailing steering axle with electro-pneumatic steering lock * Locking of the trailing axle from the cab for shunting purposes, activated via EBS (no truck-side installation required) ----Suspension: * Air suspension with lifting and lowering system as well as RtR valve ----Electrics / Lighting: * Smart-Board mounted on the trailer as an infotool, with pressure sensors for total axle load display * 15-pin power connector * LED lighting 12 / 24 V * Removable LED beacon at the rear * 2 additional LED reversing lights * 7-pin socket at the rear for oversize lighting * Side marker lights with indicator function * Tire pressure monitoring system with display option in the truck via EBS signal (no truck-side installation required) ----General attachments: * Side underrun protection * Landing legs at the front and swing-down supports at the rear of the chassis * Straight steel sheet fenders * Spare wheel holder in front of the front wall cross member (spare wheel not included) * Mechanically adjustable warning sign packages front and rear * Pivoting arm as a carrier for connection lines from the truck to the semi-trailer ----Low loader deck: * 2nd king pin position * Fifth wheel platform with front corners beveled at 45°, front toolbox of galvanized, powder-coated steel sheet (W = 2,480 x H = 500 x L = 665 mm) with folding lid * 400 mm aluminum drop sides (in RAL color of your choice), foldable and removable, on the sides of the fifth wheel platform * Rear board -150 mm- plugged in high * Rear beveled section at the fifth wheel platform leading to the low bed, approx. 700 mm long with checker plate cover; at the end, a perforated strip for hanging aluminum drive-on ramps * Fifth wheel platform with 50 mm clamped wooden planks, low bed platform with 60 mm clamped wooden planks * Tread plate over the axles * 9x mechanical folding extensions to 3 m overall width, except in the rear bevel (extension planks available with closed storage compartment running transverse to the driving direction under the loading area) * 3 recesses under the fifth wheel platform for storing optional aluminum drive-on ramps or wooden planks for wheel recess covers ----Load securing (LaSi package): Fifth wheel platform: * Perforated outer frame with 45° edges, hole pattern for lashing equipment (2 t lashing force per lashing point at minimum spacing of 480 mm) * 3x 13.4 t lashing rings recessed in the floor on each side (1x on the fifth wheel platform, 1x on the side members after the step, 1x above the middle axle next to the side member) Low loader platform: * 3x 13.4 t lashing rings on the outer frame on each side (1x at start of step on the fifth wheel platform, 1x at start of the ramp, 1x at end of the ramp) * 2x 10 t lashing rings on each side (1x between front wheel well and 1st axle, 1x between 2nd and 3rd axle) * 3x 5 t lashing rings on each side, bolted to the external frames of the wheel wells (2 at the front, 1 at the rear wheel well) ----Excavator arm trough: * Extended excavator arm trough from the end of the last rigid axle over the steering axle to the rear cross member, continuous, with internal reinforcement profile approx. W = 770 mm x dept

Condition: used, maximum load weight: 13,700 kg, overall weight: 18,000 kg, axle configuration: 2 axles, first registration: 03/2026, next inspection (TÜV): 03/2027, loading space length: 7,000 mm, loading space width: 2,480 mm, Year of construction: 2026, * TRA 18.0: * 2 in 1 = for roll-off containers and as a low-bed trailer ----Brakes: * EBS electronic braking system * Emergency release system for spring brake cylinders * Drum brakes ----Axles: * 2 x 10-ton Gigant axles ----Suspension: * Air suspension with lifting and lowering system and RTR valve ----Drawbar: * Curved drawbar, 2,000 mm long, with pivoting drawbar eye 40 / 50 mm (without 8° eye) * GHD height adjustment system instead of drawbar spring ----Electrical system / Lighting: * Tire pressure monitoring with display option in the truck via EBS signal - without truck-side installation - * LED tail lights 12 / 24 V * 15-pole power socket ----General components: * Toolbox made of powder-coated sheet steel, approx. 1,000 x 300 x 600 mm * Spare wheel holder on the right side * Reflective contour marking on the sides and rear * Side impact protection * Plastic quarter fender with splash guard * Plastic impact protection buffer at the rear * Foldable A-frame sign at the rear ----Loading area: * Main frame with raised outer frame for guiding the roll-off containers * Sheet steel floor with recesses for the rollers in the bogie area * Continuous length of 5,500 - 7,000 mm possible * Pneumatic 4-point clamping locking system and mechanical plug-in stop angles at the front in the track, load securing certificate according to DIN 30722 - 1 * Welded bead as anti-slip coating in the track area of the ramp * Mechanical support legs at the rear ----Load securing: * 1 pair of 10-ton UVV lashing rings at the front on the end wall support * 3 pairs of 10-ton UVV lashing rings on the sides in the outer frame * 4 x 2-ton lashing eyes in cloverleaf design on each side * 4 x 8-ton lashing brackets embedded in the outer frame ----Ramps: * 1 pair of aluminum loading ramps (10.6 tons / pair) 2,800 x 470 mm, suitable for vehicles with rubber tires and tracked vehicles (lockable storage compartment from the rear) ----Painting: * Chassis, bogie, locking parts, rear support legs hot-dip galvanized * but the drawbar, axles and air tank are painted in a black tone ----Information: * Vehicle has full manufacturer's warranty until 03/2027 * Errors and prior sale are subject to change * The trailer is in new condition and has only been used a maximum of 5 times Lodpfx Adszihcijhort ----Delivery time: * Available for immediate delivery from Egestorf near the A7

Condition: new, maximum load weight: 6,870 kg, overall weight: 9,900 kg, axle configuration: 1 axle, Year of construction: 2026, * KWH 9.9 ML: ----Brakes: * EBS braking system * Drum brake * Emergency release device for spring-loaded cylinders Lsdsu I Iq Eepfx Adhert ----Axle: * BPW axle ----Suspension: * Parabolic springs ----Drawbar / Flange drawbar: * Drawbar with 40 mm threaded drawbar eye (height-adjustable in mm) ----Electrical system / Lighting: * 15-pole electrical connector * LED lighting * Flashing LED side marker lights * TPMS (Tire Pressure Monitoring System) ----General components: * Front support winch * Spring-assisted square tube supports at the rear with base plate, safety locking pins for various support heights * Enclosed fenders made of sheet steel with splash guard * Enclosed side impact protection, can be used as an advertising surface * Plastic toolbox with bottom insert (horizontal installation), approx. 500 x 350 x 400 mm ----Superstructure: * Swiveling cable drum superstructure, width between the drum arms 1,700 mm, with clamping mechanism for securing the drum at the ends of the support arms, as well as a locking mechanism of the cable drum superstructure to the chassis by means of a centrally arranged claw lock * Motor-hydraulic drum drive with oil motor * Valves and sliding, rubber-coated drive rollers * Hydraulic speed control and brake for drum drive * Steel drum shaft with 76 mm diameter, centering and rotatable ends * 1 pair of centering cones made of polyamide, stepped ----Chassis: * Chassis made of torsion-resistant square tubes and cross members ----Pump unit: * Hydraulic pump unit with diesel engine * Fuel tank and manual starter * 6.5 HP with gear pump (150 bar) ----Tires: * 315/80 R 22.5 ----Unladen weight: * 2,690 kg unladen weight ----Paint finish: * Vehicle is hot-dip galvanized ----Information: * New vehicle with full manufacturer's warranty * Errors and prior sale excepted ----Delivery time: * Immediately available from Egestorf

Condition: new, maximum load weight: 6,870 kg, overall weight: 8,800 kg, axle configuration: 1 axle, Year of construction: 2026, * KWH 9.9 ML: ----Brakes: * EBS braking system * Drum brake * Emergency release device for spring-loaded cylinders ----Axle: * BPW axle ----Suspension: * Parabolic springs ----Drawbar / Flange coupling: * Drawbar with 40 mm screwed coupling (height-adjustable, in mm) ----Electrical system / Lighting: * 15-pole power connector * LED lighting * Flashing LED side marker lights * TPMS (Tire Pressure Monitoring System) ----General components: * Front support jack * Spring-assisted square tube supports at the rear with base plate, safety locking pins for various support heights * Closed steel sheet fenders with splash guards * Closed side impact protection, usable as an advertising space * Plastic toolbox with base insert (horizontal installation), approx. 500 x 350 x 400 mm ----Superstructure: * Swiveling cable drum superstructure, width between the drum arms 1,700 mm with a clamping mechanism to secure the drum at the end of the support arms, and a locking mechanism for the cable drum superstructure with the chassis by means of a centrally arranged claw lock * Motor-hydraulic drum drive with oil motor * Valves and adjustable rubber-coated drive rollers * Hydraulic speed control and brake for drum drive * Steel drum shaft with 76 mm diameter, centering and rotatable ends * 1 pair of centering cones made of polyamide, stepped ----Chassis: * Chassis made of torsionally rigid square tubes and cross members ----Pump - Unit: * Hydraulic pump unit with diesel engine * Fuel tank and manual starter * 6.5 HP with gear pump (150 bar) ----Tires: * 315/80 R 22.5 ----Unladen weight: * 2,690 kg unladen weight ----Paintwork: * Vehicle is hot-dip galvanized Lrsdpou I Iqlsfx Adhjt ----Information: * New vehicle with full manufacturer's warranty * Errors and prior sale are subject to change ----Delivery time: * Available for immediate delivery from Egestorf

Condition: new, maximum load weight: 6,870 kg, overall weight: 9,900 kg, axle configuration: 1 axle, Year of construction: 2026, * KWH 9.9 ML: ----Brakes: * EBS braking system * Drum brake * Emergency release device for spring-loaded cylinders ----Axle: * BPW axle ----Suspension: * Parabolic springs ----Drawbar / Flange drawbar: * Drawbar with 40 mm threaded drawbar coupling (height-adjustable in mm) ----Electrical system / Lighting: * 15-pole power plug * LED lighting * Flashing LED side marker lights * TPMS tire pressure monitoring system ----General components: * Front support jack * Spring-supported square tube supports at the rear with base plate, safety locking pins for different support heights * Closed mudguards made of sheet steel with splash protection * Closed side impact protection, can be used as an advertising space * Plastic tool box with base insert (horizontal installation) approx. 500 x 350 x 400 mm ----Superstructure: * Swiveling cable drum superstructure, width between the drum arms 1,700 mm with a clamping device to secure the drum at the ends of the support arms, and a locking mechanism for the cable drum superstructure with the chassis using a centrally arranged claw lock * Motor-hydraulic drum drive with oil motor * Valves and sliding, rubber-coated drive rollers * Hydraulic speed regulator and brake for drum drive Lredpfx Adju I Iqxshot * Steel drum shaft with 76 mm diameter, centering, and rotatable ends * 1 pair of centering cones made of polyamide, stepped ----Chassis: * Chassis made of torsion-resistant square tubes and cross members ----Pump unit: * Hydraulic pump unit with diesel engine * Fuel tank and manual starter * 6.5 HP with gear pump (150 bar) ----Tires: * 315/80 R 22.5 ----Unladen weight: * 2,690 kg unladen weight ----Painting: * Vehicle is hot-dip galvanized ----Information: * New vehicle with full manufacturer's warranty * Errors and prior sale excepted ----Delivery time: * Immediately available from Egestorf

Condition: used, maximum load weight: 4,960 kg, overall weight: 10,500 kg, first registration: 04/1993, next inspection (TÜV): 01/2026, loading space length: 6,260 mm, loading space width: 2,430 mm, loading space height: 2,430 mm, loading space volume: 37 m³, Equipment: ABS, tail-lift, 2-axle tandem refrigerated trailer 7 m with 1-ton tail lift. * THERMOKING LND-II MAX (diesel engine) and standby cooling 380 V ELECTRIC * Vehicle number for customer inquiries: 4593 * Tail lift * Air suspension * EBS * Anti-lock braking system (ABS) No liability for typographical or printing errors. Sales to business customers only. Subject to prior sale and errors. Changes, interim sale, and mistakes expressly reserved. The description is provided for vehicle identification purposes and does not constitute a warranty in the legal sense. The purchase contract description is binding. * TOP SERVICE + QUALITY * We are happy to provide you with a LEASING-FINANCING-HIRE PURCHASE offer Warranty insurance available on request from the insurer * TÜV / UVV LBW / Tachograph inspection and installation of OBU device by our local partners * Customs plates valid for 30 days All export customs documentation possible, but must be requested separately * Toll for Toll-Collect can be arranged in-house * Free transfer from Stuttgart Airport or Metzingen (Württ) train station Lrjdpfeykxflox Adhot * TRAIN STATION FOR ARRIVAL: 72555 METZINGEN/WÜRTT. * FOR ENGLISH * Andreas Pittas * Thomas Pittas * Alexander Pittas * Robin Pittas WHATSAPP Number * * ---- Visit our website at * Always over 200 vehicles in stock

Condition: new, maximum load weight: 13,490 kg, overall weight: 18,000 kg, axle configuration: 2 axles, loading space length: 7,000 mm, loading space width: 2,480 mm, Year of construction: 2025, TRA-Kombi 18.0: * 3 in 1 = suitable for roll-off containers, skip loaders, and as a low-loader ----Brakes: * EBS-E (electronic braking system) * Emergency release system for spring brake cylinders * Drum brakes ----Axles: * 2 x 10.5-ton Gigant axles ----Suspension: * Air suspension with manual lowering at the rear ----Drawbar: * Pneumatically lowerable drawbar, 2,100 mm long, with 40 mm drawbar eye and height adjustment ----Electrical System / Lighting: * TPMS (tire pressure monitoring system), display option in the truck via EBS signal (without truck-side installation) * LED tail lights 12 / 24 V * 15-pole electrical connector ----General Components: * Tool box made of powder-coated sheet steel * Spare wheel holder in body construction on the right side * Closed side underrun protection * Plastic quarter fenders with splash guards * Plastic rear impact protection buffer * Foldable A-frame sign at the rear ----Loading Area: * Hot-dip galvanized main frame with raised outer frame for guiding roll containers Ljdpfx Aewb Rakodhsrt * Sheet steel floor with recesses for rollers in the bogie area * With roll-off container transport, a continuous length of 5,500 - 7,000 mm is possible * Pneumatic 4-way clamp locking system as well as mechanical, plug-in stop angles at the front in the track * Transport of up to 2 skip loaders with a maximum volume of 10 m³ is possible * Including 8 repositionable container stops for lateral centering of the containers, the front 4 container stops are plugged in with pivoting stops * Weld bead as an anti-slip surface in the track area of the loading ramp * Mechanical support legs at the rear ----Load Securing: * 3 pairs of 10-ton UVV lashing rings on the side for attaching tensioning elements for positive and frictional securing of the containers, each with 4 lashing straps in a cloverleaf design (on the side) * 1 pair of 13.4-ton UVV lashing rings at the front * 4 x 8-ton lashing eyes embedded in the outer frame on each side ----Ramps: * Aluminum loading ramps (10.6 tons / pair), 2,800 x 470 mm, suitable for rubber-tired and tracked vehicles (lockable storage compartment from the rear) ----Painting: * Reflective contour striping on the side and rear * Frame hot-dip galvanized * Axles, drawbar painted black ----Information: * Load securing certificate according to DIN 30722-1 * Load securing certificate according to DIN EN 12195-1, DIN EN 12640, DIN EN 12642 and VDI 2700 * --Permissible total weight of 20,000 kg technically possible-- * New vehicle without initial registration with manufacturer's warranty * Errors and prior sale excepted ----Delivery Time: * Available immediately from Egstorf

Condition: new, maximum load weight: 37,560 kg, overall weight: 48,000 kg, axle configuration: 3 axles, Year of construction: 2026, * TS 3 RM ML 30.0: ----Brakes: * Wabco EBS-E (electronic braking system) * Emergency release device for spring brake cylinders * Drum brakes ----Axles: * 3 x 11 t BPW axles * Start assist for maneuvering purposes on the first axle, activated via EBS (no truck-side installation required) * Last axle is a trailing steering axle with electro-pneumatic steering lock * Lock for the trailing axle, actuated from the driver's cab for maneuvering purposes via EBS (no truck-side installation required) ----Suspension: * Air suspension with raise/lower system and RtR valve ----Electrical / Lighting: * Smart-Board installed as an information tool on the trailer, with pressure sensors for total axle load display * 15-pin power connector * LED lighting 12/24 V * Removable rear LED beacon * 2 additional LED reverse lights * 7-pin socket at rear for overlength lighting * Side marker lights with indicator actuation * Tire pressure monitoring with display option in the truck via EBS signal (no truck-side installation required) ----General Attachments: * Side underrun protection * Landing gears at the front and swing-out supports at the rear * Straight steel fenders * Spare wheel carrier in front of the bulkhead crossmember (without spare wheel) * Mechanically adjustable warning panel sets at front and rear * Pivoting arm as a carrier for connection lines from the truck to the trailer ----Low Loader Bed: * Second kingpin position * Fifth-wheel platform with 45° chamfered front corners and front toolbox made of galvanized, powder-coated steel plate (W = 2,480 mm x H = 500 mm x L = 665 mm) with hinged lid * 400 mm high aluminum sideboards (RAL color of choice), foldable and removable on the fifth-wheel platform * 150 mm high plug-in rear wall * Rear slope on the fifth-wheel platform towards the low-bed, approx. 700 mm long with tread plate covering and a perforated bar at the end for hooking on aluminum ramps * Fifth-wheel platform with 50 mm clamped timber planks, and low-loader deck with 60 mm clamped timber planks * Tear plate over the axles * 9 mechanical swing-out extensions for total width of 3 m (not on rear slope), extension boards available with a transverse storage compartment under the loading area Lsdoykx Nqopfx Adhert * Prepared for 3 insertion shafts under the fifth-wheel platform for storing either aluminum ramps or timber planks for wheel recess covers * Preparation for container locks on the swan neck ----Load Securing (LaSi Package): Fifth-wheel Platform: * Perforated outer frame, bent at 45°, with hole pattern for lashing equipment (2 t lashing force per lashing point at a minimum spacing of 480 mm) * On each side, 3 x 13.4 t recessed lashing rings in the floor (1 on the fifth-wheel platform, 1 on the longitudinal member after the neck step, 1 above the middle axle next to the longitudinal member) Low Loader Platform: * On each side, 3 x 13.4 t lashing rings on the outer frame (1 at the neck step of the fifth-wheel platform, 1 at the start of the ramp, 1 at the end of the ramp) * On each side, 2 x 10 t lashing rings (1 between the front wheel recess and the first axle, 1 between the 2nd and 3rd axle) * On each side, 3 x 5 t lashing rings bolted to the outer frame of the wheel recesses (2 at the front, 1 at the rear wheel recess) ----Excavator Arm Rest: * Extended excavator arm rest from the end of the last fixed axle over the steering axle up to the rear crossmember, continuous with internal reinforcement profile, approx. 770 mm wide x T at t

Condition: used, empty load weight: 3,250 kg, maximum load weight: 10,250 kg, overall weight: 13,500 kg, axle configuration: 2 axles, first registration: 09/2004, loading space length: 4,500 mm, loading space width: 2,420 mm, loading space height: 600 mm, total length: 6,500 mm, total width: 2,550 mm, total height: 1,900 mm, suspension: steel, tire size: 385/55R19.5, color: orange, mileage: 1,001 km, gearing type: other, front tire size: 385/55R19,5 160J, rear tire size: 385/55R19,5 160J, driver cabin: other, Vehicle location: Bovenden, steel structure, leaf spring suspension, 2 axles, BPW axles, tandem axle, underbody protection, front supports, rear supports, swing-out tailgates, adjustable drawbar. Lodpfxjznldus Adhort Body: 3-sided tipping trailer, 2x BPW axles, drum brakes! Loading height approx. 1200mm! ACCESSORY INFORMATION WITHOUT GUARANTEE, subject to changes, prior sale and errors!

Condition: new, maximum load weight: 23,210 kg, overall weight: 30,000 kg, axle configuration: 3 axles, Year of construction: 2026, Equipment: ABS, * T 3: * EBS braking system * Emergency release device for spring accumulators * Drum brakes * 3 x 11 tons BPW Eco axles * Parabolic springs * Mechanical axle compensation at the rear * Side impact protection * Swivel supports at the rear on the chassis frame Ledjq Dyv Ispfx Adhort * Mechanically adjustable warning sign packages at the front and rear * Front axle with closed plastic fenders and rear axle with straight, galvanized steel splash guards, each with splash protection * Reflective contour strip on the sides and rear * Hinged cover (hot-dip galvanized) for the toolbox in the turntable platform * Toolbox made of galvanized sheet steel, approx. 650 x 300 x 600 mm - black powder coated - mounted on the side under the chassis * 15-pole power connector * LED lighting 12 / 24 V * LED rotating beacon (removable) at the rear * Drawbar with 40 mm towing eye and height adjustment via coil spring and tension lock * 4 lashing pockets on each side (but no lashing bars included) with simultaneous lashing capability * La-Si package consisting of: 2 lashing eyes (6.4 tons) at the front left and right on the main frame of the turntable platform * 5 pairs of UVV lashing rings, swivel and lowerable * Loadable in all directions and embedded in the outer frame in the corners, 13.4 tons, otherwise 10 tons * 6 pairs of mechanical folding outriggers for a total width of 3 m (but not in the rear slope) * Extension boards under the loading area, stored in a storage compartment * Excavator arm support over the rear axle up to the end member, approx. 2,100 mm long (2 pairs of 6.4 tons lashing rings on the side in the excavator arm support) * Hydraulic folding ramps (approx. 4,650 x 720 mm) with hydraulically extendable front section and load-holding check valves, hydraulic side ramp adjustment * Hydraulic flow divider in the trailer (for hydraulic pump output in the truck of over 40 liters up to max. 140 liters / min), dual-line hydraulics * Loading area above the slewing ring: approx. 1,960 x 2,520 mm * Rear loading area: approx. 6,500 x 2,520 mm (incl. 860 mm approach ramp) * Loading height when loaded approx. 860 mm +/- 30 mm compensating unit * Chassis, turntable, folding outriggers, rear support legs and loading ramps hot-dip galvanized. * Axles, springs, drawbar, air tank, etc. painted in a black tone * New vehicle with manufacturer's warranty * Errors and prior sale are subject to change * Available for immediate delivery from Egestorf

Condition: new, maximum load weight: 6,900 kg, overall weight: 9,900 kg, axle configuration: 1 axle, Year of construction: 2026, * KWH 9.9 ML: ----Brakes: * EBS braking system * Drum brake ----Axle: * BPW axle ----Suspension: * Parabolic springs ----Electrical System / Lighting: * TPMS (Tire Pressure Monitoring System) * 15-pin electrical connector * LED lighting * Flashing LED side marker lights ----Drawbar / Flange Coupling: * Drawbar with 40 mm screw coupling (height adjustable in mm) ----General Components: * Front support jack * Spring-supported square tube supports at the rear with base plate, safety locking pins for different support heights * Closed steel sheet mudguards with splash protection * Closed side impact protection, usable as an advertising area * Plastic toolbox with floor insert (horizontal installation), approx. 500 x 350 x 400 mm ----Superstructure: * Swiveling cable drum superstructure, width between the drum arms 1,700 mm, with tensioning closure for securing the drum at the ends of the support arms, as well as a locking mechanism for the cable drum superstructure with the chassis via a centrally arranged claw lock * Motor-hydraulic drum drive with oil motor * Valves and adjustable rubber-coated drive rollers * Hydraulic speed controller and brake for drum drive * Steel drum shaft with 76 mm diameter, with centering and rotatable ends * 1 pair of centering cones made of polyamide, stepped arrangement * Preparation of steel structure and hydraulics for retrofitting a separate motor ----Chassis: * Chassis made of torsion-resistant square tubes and cross members ----Hydraulics: * Hydraulic line for supply and return ----Tires: * 315/80 R 22.5 tires ----Painting: * Vehicle is hot-dip galvanized ----Information: * 2,690 kg unladen weight * New vehicle with full manufacturer warranty * Errors and prior sale excepted ----Delivery time: * Available for immediate delivery from Egestorf Lodpfjxyniwsx Adhsrt

Condition: used, empty load weight: 4,500 kg, maximum load weight: 13,500 kg, overall weight: 18,000 kg, axle configuration: 2 axles, first registration: 08/2015, next inspection (TÜV): 07/2025, loading space length: 4,800 mm, loading space width: 2,400 mm, loading space height: 1,000 mm, color: blue, Year of construction: 2015, gearing type: other, driver cabin: other, Equipment: ABS, * German trailer * Condition, see photos * Müller-Mitteltal 3-way tipper, type KA-TA-R 18.0 tandem * Tipper dimensions: 4,800 x 2,400 x 1,000 mm * Roll tarp * Air suspension * Disc brakes * Platform * Jost support leg * Payload 13,500 kg If a new TÜV inspection is required, we are happy to provide you with an offer from our partner workshops. Our offer generally does NOT include a new TÜV inspection, new DGUV, new SP, or new UVV. You can find more trucks on our homepage at We speak the following languages: German, English, Polish, Turkish Lredpfxowz H Nbj Adhjt Note: We offer and strongly recommend a viewing and inspection of the goods to ensure the buyer does not have any misconceptions regarding condition or suitability. Viewings and inspections are possible at any time by appointment and are expressly encouraged. All information provided without guarantee. We are not liable for errors or incorrect information in the offer. The buyer is obliged to independently verify the condition and features of the goods/vehicles. Subject to alterations, prior sale, and errors.

Condition: new, maximum load weight: 29,850 kg, overall weight: 38,000 kg, axle configuration: 2 axles, loading space length: 8,000 mm, loading space width: 2,520 mm, Year of construction: 2026, TS 2 ML ----Brakes: * EBS-E (electronic braking system) * Emergency release device for spring brake cylinders * Drum brakes ----Axles: * 2 x 10 t axles * Rear axle as a trailing steering axle with electro-pneumatic steering lock activated by PIN when reverse gear is selected * Additional lock for the trailing axle, operated from the driver's cab for maneuvering purposes – no truck-side installation required – assigned to PIN 10. The lock must be deactivated before driving on public roads ----Suspension: * Air suspension with lifting and lowering function as well as RtR (Ride to Recover) function ----Electrics / Lighting: * Tire pressure monitoring system with display option in the truck dashboard via EBS signal – no truck-side installation required * LED tail lights 12 / 24 V * Flashing side marker lights * LED reversing lights switched via reverse gear * SmartBoard installed as info tool with pressure sensors exclusively for total axle load display * 7-pin socket at the rear for overlength lighting * Removable LED rotating beacon at the rear ----General attachments: * Aluminum air tanks * Mechanical crank landing legs * Galvanized steel mudguards * Swivel arm as a carrier for connection lines mounted in front of the front panel ----Warning package: * Mechanically adjustable warning sign package ----Low-bed platform: * 50 mm flooring made of larch / Douglas fir instead of spruce / fir * Rear slope – 700 mm long – on the gooseneck deck to the low-bed with checker plate covering, and perforated strip at the end for attaching aluminum approach ramps * Tread plate cover over wheels * SP-Combo package: toolbox with 45° corners, made of galvanized sheet steel, additionally powder-coated in RAL 9006 white aluminum, mounted on the platform approx. 2,480 x 500 mm * Flip-top lid as well as side doors in the slanted corners * Folding aluminum side walls 500 mm high on the platform, incl. folding and removable rear stanchions * Plug-in aluminum rear wall 150 mm high * Second kingpin position * Preparation for container lock * Preparation for 3 insert pockets in the inclined ramp from low-bed to gooseneck * Preparation for retrofitting folding outriggers for 3 m widening by welding the mounting brackets into the outer frame ----Load securing: Fifth wheel platform: * In the front corners and at the front, 50 mm holes for 1.2 t lashing force per hole * 2 x 16.5 t lashing rings recessed in the floor on the side at the approach slope * Perforated and bent 45° outer frame with hole pattern for lashing equipment (2 t lashing points every 480 mm) * On each side: 2 x 6.3 t retractable lashing rings recessed into the outer frame Lrodpeykx I Tjfx Adhjt Low-bed platform: * 2 x 16.5 t lashing rings recessed centrally directly in front of the approach slope to the gooseneck * On each side: 3 pairs of 13.5 t and 5 pairs of 10 t retractable lashing rings recessed into the outer frame * On each side: 4 stanchion pockets recessed into the outer frame * Profifix lashing rail centered in the longitudinal axis (lashing point 3 t per securing circle) ----Excavator arm trough: * From the end of the last rigid axle to the end cross member B = 770 mm, D = 270 mm (on each side 2 x 6.4 t lashing rings for the excavator arm trough, permanently welded) ----Ramp: * Hydraulic one-piece "ALLTEC" aluminum approach ramps approx. 3,200 x 750 mm * Load capacity 13 t per ramp (26 t per pair) * Hydraulic ramp shifting on sliding pipe of the ramp shaft ----Hydraulics: * Hydraulic flow

Condition: used, empty load weight: 3,100 kg, maximum load weight: 7,400 kg, overall weight: 10,500 kg, axle configuration: 2 axles, first registration: 10/2004, loading space length: 5,000 mm, loading space width: 2,420 mm, loading space height: 400 mm, suspension: steel, tire size: 235/75R17.5, color: orange, mileage: 1,001 km, gearing type: other, driver cabin: other, Equipment: ABS, Vehicle location: Bovenden, steel body, 2 axles, BPW axles, tandem, leaf spring suspension, ABS (anti-lock braking system), lashing eyes, underride guard, front supports, rear supports, storage box, swing-open tailgates, drawbar with adjustable height. Ljdpjztrw Sjfx Adhjrt Body: Tandem 3-sided tipper trailer with loading ramps, 2x BPW axles, drum brakes! Loading ramps available for an additional charge of €990.00 net! Loading height approx. 900mm! ACCESSORY INFORMATION WITHOUT GUARANTEE, subject to changes, prior sale and errors!

Condition: used, maximum load weight: 6,760 kg, overall weight: 10,000 kg, axle configuration: 2 axles, first registration: 10/2024, loading space length: 5,000 mm, loading space width: 2,420 mm, loading space height: 500 mm, loading space volume: 6 m³, Equipment: ABS, * 1874 - Vehicle ID for telephone inquiries * Type: KA-TA-R 11.9 * BPW axles, galvanized, leaf spring suspension, drawbar height-adjustable, rear support, 12 tie-down points, drum brakes, side panels fold down with spring support, ramps slide in, pendulum movements * Trailer derated without technical modification to a total weight of 10,000 kg * Tire 1st axle: 235/75R17.5 (10/10 mm) * Tire 2nd axle: 235/75R17.5 (9/9 mm) ----Our email address: Our service for you: - Procurement of short-term or customs license plates Lredpfx Adjzz Eumshst - Transportation/delivery throughout the EU - Customs clearance of vehicles to third countries WhatsApp for English, German, Russian and other languages:

Condition: used, maximum load weight: 8,750 kg, overall weight: 11,900 kg, axle configuration: 2 axles, first registration: 06/2024, total width: 2,550 mm, Year of construction: 2023, Müller Mitteltal KA-TA-R 11.9 tandem 3-way tipper with lots of extras. Total weight: 11,900kg Standard payload approx.: 8,750kg Clear dimensions: 5,000x2,420x500mm Tires: 385/55R19.5 4-layer paintwork, single color Wheels: silver Chassis/underbody protection: hot-dip galvanized Platform with bulkhead: hot-dip galvanized Axles/springs/fuel tank etc.: black Side and rear wall: RAL 2011 deep orange Reinforced and certified structure in accordance with EN 12642 XL including load securing certificate. (Only in conjunction with 500mm high steel side walls). Rear stanchions screwed, hot-dip galvanized, without top coat. Lashing points LC 5,000 daN recessed at the front. Net hooks integrated at the side and rear in the bearings of the central locking system to the base side wall and 2 additional pieces on the front wall. BPW axles instead of GIANT tipping platform with permanently attached front wall in hot-dip galvanized design, with screwed, galvanized rear stanchions, without additional coating (not with HARDOX floor). Due to the system, the formation of waves during hot-dip galvanization, especially with the large floor panel, cannot be ruled out; complaints in this regard are excluded from the warranty. Tires 385/55R19.5 instead of 235/75R17.5 (floor and coupling height + approx. 110 mm, Code 08.940 ramp length 3,570 mm required). 1 plastic tool box, black, lockable, W=750xH=350xD=300mm (45kg payload with even load), arrangement: on the chassis frame on the right in the direction of travel. 1 pair of aluminum docking ramps without fairway (8 t/pair), 3,570x400x105mm, suitable for rubber-tired and tracked vehicles, 55 kg/each. Two-step access in front of the front wall, on the left in the direction of travel (hot-dip galvanized). Extended connecting lines for agricultural and forestry tractors. Lsdezwa Imopfx Adhjrt Further information New: No

Condition: used, maximum load weight: 13,450 kg, overall weight: 18,000 kg, axle configuration: 2 axles, first registration: 03/2014, next inspection (TÜV): 05/2027, loading space length: 4,950 mm, loading space width: 2,370 mm, loading space height: 900 mm, loading space volume: 10 m³, Equipment: ABS, * 3-way tipper with side tipper system Lredszkfguepfx Adhot * Gigant axles * Drum brakes * ABS * Air suspension * Support legs All information is subject to change without notice / subject to prior sale.

Condition: new, maximum load weight: 8,870 kg, overall weight: 11,900 kg, axle configuration: 2 axles, loading space length: 6,270 mm, loading space width: 2,470 mm, loading space height: 400 mm, Year of construction: 2026, * ETÜ-TA-R 11.9: ----Brakes: * EBS braking system * Emergency release device for spring brake cylinders * Drum brakes ----Axle: * 2 x 5.5 ton BPW axles ----Suspension: * Parabolic springs with compensating unit ----Drawbar / Flange coupling: * Drawbar with 300 mm height adjustment * 40 mm flange coupling ----General components: Lodpfxoq Ra D Es Adhert * Jost landing gear at the front * External, hot-dip galvanized folding supports at the rear * Plastic quarter fenders * Plastic toolbox on the front right side, on the front panel ----Electrical system / Lighting: * TPMS tire pressure monitoring system * LED lighting ----Loading platform: * Loading platform 6.27 m * Suitable for container transport * 50 mm hardwood floor * Provision on the front panel for retrofitting container locking mechanisms * Bolted front panel made of smooth sheet metal * Side walls made of trapezoidal steel sheet, foldable with side board spring lifts * Steel rear wall can be slid in between the ramp supports when not in use, positioned inside in front of the front panel * Rear crossbars bolted on ----Load securing: * Perforated outer frame angled at approximately 45 degrees with a lashing force of 2 tons every 480 mm * Installation of 3-ton drop-side lashing eyes possible every 600 mm * 1 x 6.3-ton lashing eye at each front and rear corner * Various holes in the front and end beams for 1.2-ton lashing options ----Ramps: * One-piece mechanical loading ramps with spring mechanism for single-person operation, approx. 2,750 x 600 mm (can be telescoped together to 20 mm) * Approach angle at the rear approx. 860 mm ----Tires: * Tires: 235/75R17.5 ----Wheelbase: * Wheelbase: 990 mm ----Paintwork: * Hot-dip galvanized chassis, drawbar, front panel, rear wall, rear crossbars, and loading ramps * Painting of the side boards in RAL 9010 pure white * Painting of the side walls in a RAL color possible at an extra charge ----Information: * Subject to errors and prior sale * New vehicle with manufacturer's warranty ----Delivery time: * Available for immediate delivery from Egestorf

Condition: used, empty load weight: 2,910 kg, maximum load weight: 7,590 kg, overall weight: 10,500 kg, axle configuration: 2 axles, first registration: 09/2009, next inspection (TÜV): 04/2025, loading space length: 4,500 mm, loading space width: 2,200 mm, loading space height: 450 mm, suspension: steel, tire size: 235/75R17.5, color: blue, mileage: 1,001 km, gearing type: other, driver cabin: other, Equipment: ABS, Vehicle location: Bovenden, steel body, 2 axles, BPW axles, tandem, leaf spring suspension, ABS (anti-lock braking system), lashing eyes, underbody protection, front support, rear support, swing flaps. Construction: Tandem 3-way tipping trailer with ramp shaft. Loading ramps available for an additional charge of €900.00 net! ACCESSORIES INFORMATION IS PROVIDED WITHOUT GUARANTEE. Subject to changes, prior sale, and errors! Lsdpfxjv S H Sfs Adhert - .

Condition: new, maximum load weight: 9,130 kg, overall weight: 11,900 kg, axle configuration: 2 axles, loading space length: 5,500 mm, loading space width: 2,010 mm, loading space height: 325 mm, Year of construction: 2026, * ETS-TA-B 11.9: * Wabco EBS (electronic braking system) * TPMS (tire pressure monitoring system) * Drum brakes, 2 x 5.5 t Gigant axles Lrsdpfx Adswyhzpshjt * Parabolic springs with compensating unit * Height-adjustable drawbar, approx. 300 mm * BPW landing gear * Mechanical drop supports at the rear * Plastic toolbox at the front right on the bulkhead * Side underrun protection * LED lighting * 50 mm softwood floor * One 6.3 t lashing point in the corners at the front bulkhead and rear end member, plus two 6.3 t UVV-compliant lashing rings recessed in the outer frame on each side * One-piece mechanical grating ramps with spring mechanism for single-person operation, approx. 2,350 x 870 mm (20 mm inner spacing, ramps fixed and not movable) * Bulkhead, side walls, mudguards, and drawbar hot-dip galvanized * Axles, springs, air reservoir, and front landing gear painted in black * New vehicle with full manufacturer's warranty * Subject to errors and prior sale * Available immediately from Egestorf