Used Müller-Mitteltal Semitrailers for sale (246)

Condition: new, overall weight: 11,900 kg, maximum load weight: 8,620 kg, axle configuration: 2 axles, loading space length: 5,500 mm, loading space width: 2,420 mm, loading space height: 500 mm, Year of construction: 2024, * KA-TA-R 11.9: * 5.5-meter-long bridge completely finished in RAL 9010 white * Tire pressure monitoring (RDÜ) * Electronic braking system (EBS) * Emergency release device for spring-loaded cylinders * Drum brakes * 2 x 5.5-ton Gigant axles * Parabolic springs with tandem compensating unit * 300 mm height-adjustable, hot-dip galvanized drawbar with 40 mm flange drawbar eye * Jost mechanical landing gear at the front Knjdpjl Thx Ejfx Ablsc * 2 mechanical landing gears at the rear Hot-dip galvanized folding supports * Toolbox made of galvanized sheet steel on the right side * 15-pin power connector * LED taillights * Hot-dip galvanized bolted underride protection * Toolbox made of galvanized sheet steel on the right side * Plastic quarter fenders * Net hooks on the sides and rear in the central locking bearings, as well as 3 on the front wall * Hot-dip galvanized chassis * Steel pallet, 3-way tipping body * Continuous side walls without center stanchions, foldable with side wall spring lift * Tailgate foldable and swinging via manual central locking * Hot-dip galvanized bolted rear stanchions * 1 x 5 ton lashing ring in each corner and 4 x 3 ton lashing rings on each side Lashing eyes embedded in the outer frame * 4 mm sheet steel floor * Rear mounting rail for the docking ramps * Preparation for later retrofitting of side wall extensions * Reinforced body with load securing certificate according to EN 12642 XL * 1 pair of aluminum docking ramps approx. 3,310 x 400 mm (load capacity 8 tons per pair) suitable for rubber-tired and tracked vehicles * Rear-locking storage compartment embedded in the chassis below the loading area * Axles, springs, air tank, drawbar, and landing gear painted in a black tone * Body color: RAL 9010 pure white * Side walls and tipping body painted in a RAL color available for an additional charge * Tires: 235/75R17.5 * Wheelbase: 990 mm * New vehicle, not registered, with manufacturer's warranty * Errors and prior sale subject to change * Available immediately Egestorf on the A7

Condition: used, overall weight: 24,000 kg, axle configuration: 3 axles, first registration: 05/2008, Year of construction: 2008, Equipment: ABS, * Müller Miteltal T 30.0 compact * Year of construction : 2008 * Leaf suspension * : 24.000 Kg * Ramps Knsdpfxsuz I Rrj Abljc * 3 axles Internal number : 24A039

Condition: used, overall weight: 18,000 kg, axle configuration: 2 axles, loading space length: 9,500 mm, loading space width: 2,550 mm, loading space height: 1,250 mm, first registration: 10/2006, * Combi trailer for roll-off & set-down containers * Pneumatic container locking system * Lowerable drawbar * BPW axles air/air As viewed or offered, without further services / accessories. Our offer is generally without new TÜV approval. If a new TÜV inspection is required, we will be happy to make you an offer from our partner workshops! The vehicle may have advertising stickers and/or lettering. Our general terms of delivery and payment apply. We support you with export, preparation of export documents, procurement of license plates, supplier's declaration, etc.! Knsdpfx Ajizy Nysblsc The information provided in advertisements, the Internet, price tags and pictures are non-binding descriptions and do not serve as guaranteed characteristics. The seller accepts no liability/warranty for typing and data transmission errors. Any equipment listed must be checked separately. We expressly reserve the right to prior sale, as we also offer this item on other portals. Accessories details without guarantee. Subject to alterations, prior sale or errors excepted. We offer and strongly recommend a viewing and inspection to ensure that the buyer has no misconceptions about the condition and suitability of the item. Viewings and inspections are possible at any time by appointment and are expressly desired.

Condition: used, overall weight: 10,000 kg, empty load weight: 2,700 kg, maximum load weight: 7,300 kg, axle configuration: 2 axles, loading space length: 5,020 mm, loading space width: 2,460 mm, loading space height: 400 mm, first registration: 02/2007, suspension: steel, tire size: 235/75R17.5, color: orange, mileage: 1,001 km, gearing type: other, driver cabin: other, Equipment: ABS, Vehicle location: Bovenden, 2-axle, BPW axles, tandem, leaf suspension, ABS (anti-lock braking system), lashing eyes, mechan. Ramps, front support, storage box, height-adjustable drawbar Body: Tandem low loader trailer with mechanical ramps 2x BPW axles, drum brakes! Kjdpfx Abjwvikqjlenc Loading height approx. 930mm! Ramp length approx. 2600mm! ACCESSORIES WITHOUT WARRANTY, subject to alterations, prior sale and errors excepted! - .

Condition: used, overall weight: 32,000 kg, maximum load weight: 25,230 kg, axle configuration: 2 axles, first registration: 06/2012, Equipment: ABS, Müller Mitteltal 2-axle concrete semi-trailer type SF32 BM/BT Body type: HTM 1004 Liebherr 10 m³ from year of construction 2012, BPW axles, drum brakes, air suspension, lift axle, underride guard, EBS, ABS 1st hand inspection book Permissible total weight: 32000 KG Unladen weight: 6770 KG Kedpfxerdt H Es Abljnc

Condition: new, overall weight: 11,900 kg, maximum load weight: 8,850 kg, axle configuration: 2 axles, loading space length: 5,000 mm, loading space width: 2,420 mm, loading space height: 500 mm, Year of construction: 2024, * KA-TA-R 11.9 "Masterline": * Hot-dip galvanized floor and bulkhead * EBS braking system * Emergency release device for spring-loaded cylinders * Tire pressure monitoring system * Drum brakes * 2 x 5.5 ton BPW axles * Parabolic springs with tandem compensating unit * 300 mm height-adjustable drawbar with 40 mm flange drawbar eye * Jost mechanical landing gear at the front * 2 mechanical landing gears at the rear Hot-dip galvanized folding supports * Plastic toolbox approx. 750 x 350 x 300 mm on the right side Ksdpsl Thymsfx Ablenc * 15-pin power connector * LED lighting * Bolted underride protection * Plastic quarter fender * Net hooks on the sides and rear in the central locking bearings, as well as two on the front wall * Steel pallet 3-way tipping body (continuous side walls - without center stanchions - foldable with side wall spring lifter) * Bolted rear stanchions * Combination steel wing doors, rear wall with two asymmetrical wings, divided by 270°, pivoting and locking, not foldable, and with additional pendulum frames for automatic rear wall opening during tipping. Locking via galvanized espagnolette and central locking * Deactivation function for automatic rear wall function when tipping backwards with the wing door open * 1 x 5 ton lashing ring in each corner and on the sides 4 x 3-ton lashing eyes embedded in the outer frame, 4 mm sheet steel floor, rear mounting rail for the landing ramps * Reinforced body with load securing certificate according to EN 12642 XL * 1 pair of aluminum landing ramps approx. 3,310 x 400 mm (load capacity 8 tons per pair) suitable for rubber-tired and tracked vehicles * Rear-lockable storage compartment embedded in the chassis below the loading area * Front wall, tipping platform, rear stanchions, underrun protection, mechanical Hot-dip galvanized drop legs * Side walls and tailgate painted in RAL 9010 pure white * Side walls can be painted in a RAL color for an additional charge * Axles, springs, flanged towing eye, air chamber, and landing gear painted in a black color * New vehicle, not registered, with manufacturer's warranty * Errors and prior sale subject to change * Available for immediate delivery from Egestorf on the A7

Condition: used, overall weight: 11,900 kg, empty load weight: 3,100 kg, maximum load weight: 8,800 kg, axle configuration: 2 axles, loading space length: 5,000 mm, loading space width: 2,420 mm, loading space height: 500 mm, first registration: 04/2018, suspension: steel, tire size: 235/75R17.5, color: yellow, mileage: 1,001 km, gearing type: other, driver cabin: other, Equipment: ABS, Vehicle location: Bovenden, 2-axle, tandem, leaf spring suspension, ABS (anti-lock braking system), lashing eyes, under-tubing, front and rear outriggers, pendulum tailgates, height-adjustable drawbar. Construction: Tandem tipping trailer with loading ramps. Currently rated at 10,000 kg, can be increased to 11,900 kg. Galvanized frame, Gigant axles, drum brakes! Knodpfswa Dwyjx Ablec Loading height approx. 950 mm! Loading ramps available for an additional charge of €1,000.00 net! ACCESSORIES INFORMATION WITHOUT GUARANTEE, subject to change, prior sale, and errors! - .

Condition: new, overall weight: 11,900 kg, maximum load weight: 8,870 kg, axle configuration: 2 axles, loading space length: 6,270 mm, loading space width: 2,470 mm, loading space height: 400 mm, Year of construction: 2025, * ETÜ-TA-R 11.9: * Loading area 6.27 m * Suitable for container transport * RDÜ tire pressure monitoring * EBS braking system * Emergency release device for spring-loaded cylinders * Drum brakes, 2 x 5.5 tonnes. BPW axles * Parabolic springs with compensating unit * Drawbar height adjustable by 300 mm * Jost landing gear at the front * External hot-dip galvanized folding supports at the rear * Plastic quarter fenders * LED lighting * Hot-dip galvanized chassis, drawbar, bulkhead, rear wall, rear stanchions, and loading ramps * 50 mm softwood floor * Device for retrofitting container locks in front of the bulkhead * Bolted smooth sheet metal bulkhead * Foldable trapezoidal steel side walls with side wall spring lifter * Steel rear wall can be inserted between the ramp brackets when not in use, inside the bulkhead * Bolted rear stanchions * Perforated outer frame, angled at approximately 45 degrees with a 2-ton lashing capacity every 480 mm * Installation of 3-ton Drop lashing rings available every 600 mm * 1 x 6.3 ton lashing ring in each of the front and rear corners * Various holes in the front and end beams for 1.2 ton lashing options * One-piece mechanical loading ramps with spring mechanism for one-person operation, approx. 2,750 x 600 mm (can be collapsed to within 20 mm) * Rear approach slope approx. 860 mm * Wheelbase: 990 mm * Tires: 235/75R17.5 * Side walls painted in RAL 9010 pure white * Side walls painted in a RAL color available for an additional charge * Plastic toolbox * Subject to errors and prior sale * Available for immediate delivery from Egestorf Knodjq Ra D Njpfx Abljc

Condition: used, overall weight: 10,500 kg, empty load weight: 2,910 kg, maximum load weight: 7,590 kg, axle configuration: 2 axles, loading space length: 4,500 mm, loading space width: 2,200 mm, loading space height: 450 mm, first registration: 09/2009, next inspection (TÜV): 04/2025, suspension: steel, tire size: 235/75R17.5, color: blue, mileage: 1,001 km, gearing type: other, driver cabin: other, Equipment: ABS, Vehicle location: Bovenden, steel body, 2 axles, BPW axles, tandem, leaf spring suspension, ABS (anti-lock braking system), lashing eyes, underbody protection, front support, rear support, swing flaps. Construction: Tandem 3-way tipping trailer with ramp shaft. Loading ramps available for an additional charge of €900.00 net! ACCESSORIES INFORMATION IS PROVIDED WITHOUT GUARANTEE. Subject to changes, prior sale, and errors! Knedpfx Abjv S H Sfolec - .

Condition: new, overall weight: 14,400 kg, maximum load weight: 10,950 kg, axle configuration: 2 axles, loading space length: 6,270 mm, loading space width: 2,470 mm, Year of construction: 2024, * ETÜ-TA-ER 14.4 Plateau: * RDÜ (tire pressure monitoring) * EBS (electronic braking system), * Emergency release device for spring-loaded cylinders * Drum brakes * 2 x 7 ton BPW axles * Air suspension with lifting and lowering system * mechanically adjustable 3 mtr. Warning sign packages at the front and rear * Drawbar height adjustable by 300 mm with 40 mm flange drawbar eye * Drawbar shortened by approx. 200 mm to approx. 1,800 mm (thus B dimension of approx. 8,080 mm) * Support winch at the front * External folding supports at the rear * Plastic tool boxes approx. 750 x 350 x 300 mm on the left and right sides * Side impact protection * Underrun protection * Plastic quarter fender * 15-pin power plug * LED lighting system 12 / 24 V * 2 additional LED reversing lights. at the rear (switched via reverse gear) Kodpfx Abom Tgxwjljnc * 1 LED rotating beacon (removable incl. holder) at the rear * 50 mm softwood floor * 2 pairs of container locks (extendable to 3 mtr. Cont. external width) and lockable * Locking dimension pushed in according to ISO - DIN 15190 = 2,259 mm. Cont. locks pulled out = 2,819 mm (this dimension is not according to DIN) with an absolute external width of 3,000 mm * Perforated external frame bent at approx. 45 degrees with 2 ton. lashing force every 480 mm, installation of 3 ton. drop lashing brackets every 600 mm possible - 5 x 3 ton. UVV lashing brackets installed on the sides -, 1 x 6.3 ton in the corners at the front and rear. Lashing ring (at the front directly behind the cont. locks in the wooden floor and at the back in the end beam) in the front and end beam various holes for 1.2 ton lashing option * 1 pair of aluminum slide-in ramps approx. 3,570 x 410 mm (load capacity 10 ton / pair) suitable for rubber-tired and tracked vehicles * storage compartment below the loading area in the chassis from the rear * ---Chassis, drawbar, front wall, underrun protection and rear supports hot-dip galvanized--- * Axles, air tank, front support winch and flange drawbar eye painted in a black tone * New vehicle with manufacturer's warranty * Errors and prior sale subject to reservation * Available immediately from Egestorf on the A7

Condition: new, overall weight: 30,000 kg, maximum load weight: 23,500 kg, axle configuration: 3 axles, loading space length: 8,380 mm, loading space width: 2,520 mm, Year of construction: 2024, * PT 30 profile: * EBS (electronic braking system) * Emergency release device for spring-loaded cylinders * Drum brakes * 3 x 11 tonne Gigant axles * Air suspension with lifting and lowering system and RtR valve * Smart board mounted on the trailer as an information tool (for axle load display - front and rear separately) * Tire pressure monitoring with display option in the truck via EBS signal without truck-side installation * Side impact protection Knodstplwijpfx Abloc * Swivel supports at the rear of the chassis frame * Mechanically adjustable warning sign packages at the front and rear * Front plastic quarter fender with splash guard * Rear straight galvanized. Sheet steel aprons with splash guard * Reflective contour tape on the side and rear * 15-pin power plug * LED lighting 12/24 V * LED rotating beacon (removable) at the rear * Pull scissors 1,200 mm long with 40 mm pull eye and height adjustment via tension spring & turnbuckle * Tool box made of galvanized sheet steel approx. 650 x 300 x 600 mm, black powder-coated on the right side * Box in the bogie for accessories with hinged lid, 2 cont. locks permanently installed (directly after the bogie platform) * ROBOT welded ANTI-SLIP coating on the steel plate of the bogie platform (protruding weld beads) * La-Si package consisting of: 2 lashing eyes (13.4 tonnes) at the front left & right on the bulkhead support, front & rear 1 pair of UVV lashing rings (13.4 to.) and 3 pairs of UVV lashing rings (10 to.) on the side, swiveling and lowerable, loadable in all directions and embedded in the outer frame, 3 stake pockets on the side with simultaneous 2 ton lashing option * 6 pairs of mechanical folding booms for 3 m total width (but not in the rear slope) * Widening planks placed in the middle of the loading area * Hydraulic one-piece loading ramps approx. 3,000 x 720 mm * Mechanically laterally adjustable * 4-way control block for later retrofitting of hydraulic. Ramp shift * Chassis, bogie, folding boom, drop supports and ramps hot-dip galvanized * Axles, slewing ring, air tank, drawbar painted in a black tone * Loading edge when loaded approx. 910 mm +/- 20 mm air suspension, * New vehicle with manufacturer's warranty * Errors and interim purchase subject to reservation * Available for immediate delivery from Egestorf

Condition: new, overall weight: 14,400 kg, maximum load weight: 10,800 kg, axle configuration: 2 axles, loading space length: 6,270 mm, loading space width: 2,470 mm, Year of construction: 2025, * ETÜ-TA-R 14.4: * EBS braking system Kodpfx Aorwc R Rjblonc * Emergency release device for spring-loaded cylinders * Drum brakes * 2 x 7 tonnes Gigant axles * Parabolic springs with compensating unit * Drawbar height adjustable by 300 mm * Drawbar extension by 250 mm to 2,250 mm * Tire pressure monitoring with display option in the truck via EBS signal - no truck-side installation required * Front landing gear * External folding supports at the rear * 15-pin power connector * 12/24 V LED lighting system * EBS multi-voltage system for towing vehicles with 12 and 24 V electrical systems * Plastic toolbox approx. 858 x 500 x 500 mm, front right outside on the bulkhead * Side impact protection * Plastic quarter fenders * 50 mm softwood floor * Device for retrofitting control locks in front of the bulkhead * Bolted 400 mm bulkhead made of smooth sheet metal * Bolted rear stanchions * Side walls with Spring jack * Perforated outer frame, approximately 45 degrees angled, with a 2-ton lashing capacity every 480 mm, installation of 3-ton drop lashing brackets possible every 600 mm, 1 x 6.3-ton lashing ring in each of the front and rear corners, various holes in the front and end beams for 1.2-ton lashing capacity * One-piece hydraulic grating loading ramps, approximately 2,750 x 600 mm (can be collapsed to within 20 mm) * Hydraulic flow divider in the trailer (for hydraulic pump output in the truck of over 40 liters/min. up to a maximum of 140 liters/min.) * Chassis, drawbar, front wall, mechanical Hot-dip galvanized drop legs and ramps * Axles, springs, air chamber, front landing gear, and flanged towing eye painted in a black shade * Side walls painted in RAL 9010 pure white * Side walls painted in a RAL color available for an additional charge * New vehicle with manufacturer's warranty * Errors and prior sale subject to change * Available from week 15 of 2025 * Sample images

Condition: new, overall weight: 30,000 kg, maximum load weight: 16,400 kg, axle configuration: 3 axles, Year of construction: 2024, * T3 profile 30.0: * EBS-E (electronic braking system) * RDÜ tire pressure monitoring * Emergency release device for spring-loaded cylinders * Drum brakes * 3 x 11 ton BPW Eco axles * Air suspension with lifting and lowering system * SmartBoard as an information tool on the trailer with pressure sensors for pressure display for total axle load display for each axle group * Side impact protection * Mechanically adjustable warning sign packages at the front and rear * Front axle closed. Plastic fenders and rear straight galvanized sheet steel aprons, each with splash guard * Hinged lid (hot-dip galvanized) for the tool box in the bogie platform * Tool box made of galvanized sheet steel approx. 650 x 300 x 600 mm (black powder-coated) on the right side * 15-pin power plug * LED lighting 12 / 24 V * LED rotating beacon (removable) at the rear * Side marker lights with indicator control * Pull scissors with 40 mm pull eye and height adjustment via tension spring & turnbuckle * Tire pressure monitoring system with display option in the truck via EBS signal (without truck-side installation) * Rubber covering on the folding ramps and on the ramp on the left and right (approx. 860 mm long) * Rubber covering on the longitudinal beams from the front to the end beam * Hardwood floor on the running surfaces of the low-loading platform * 4 stake pockets on each side with a simultaneous 2 ton. Lashing option Knedpfxoq Dyvcj Abljc * La-Si package consisting of: 5 pairs of UVV lashing rings that can be swiveled and lowered, can be loaded in all directions and are embedded in the outer frame - 13.4 tons in the corners, otherwise 10 tons * 6 pairs of mechanical folding booms for 3 m total width (but not in the rear slope) * Plank holder under the loading area in the longitudinal direction * Roller stop raised in front of the front beam with 1 x 6.4 ton lashing eye on each side * Hydraulic folding ramps (approx. 4,650 x 720 mm) with hydraulically extendable tip section and load holding valves * Hydraulic lateral ramp shifting * Hydraulic rear support (single-stage cylinder) * Hydraulic. Flow divider in the trailer (with hydraulic pump output in the truck of over 40 liters up to max. 140 liters/min.) * Hydraulic control block splash-proof * Two-line hydraulics * Loading area above the turntable: approx. 1,960 x 2,520 mm, * Rear loading area: approx. 6,500 x 2,520 mm (incl. 860 mm approach slope) * Loading height when loaded approx. 890 mm +/- 20 mm air suspension * Chassis, bogie, roller stop, folding extensions & ramps hot-dip galvanized. * Axles, turntable, pull scissors, air tank etc. painted in a black tone * Loading height when loaded: approx. 890mm +/- 20mm * New vehicle with manufacturer's warranty * Errors and prior sale subject to reservation * Available for immediate delivery from Egestorf

Condition: new, overall weight: 40,000 kg, maximum load weight: 31,000 kg, axle configuration: > 3 axles, loading space length: 9,290 mm, loading space width: 2,520 mm, loading space height: 950 mm, * PT 40.0 profile: * Wabco EBS-E (electronic braking system) * Emergency release device for spring-loaded cylinders * Drum brakes * 4 x 11 tonne Gigant axles * Air suspension with lifting and lowering system and RtR valve * Manometer pressure indicator for determining load weight (axles separated into 2 air suspension circuits) * Side impact protection * Swivel supports at the rear of the chassis frame * Mechanically adjustable warning sign packages at the front and rear * Front plastic quarter fender with splash guard * Rear straight galvanized. Sheet steel aprons with splash guard * Reflective contour tape on the side and rear * EBS multi-voltage system with 12 & 24 V electrics * 15-pin power plug * LED lighting system 12 / 24 V * LED rotating beacon (removable) at the rear * 2 LED reversing lights (switched via reverse gear) * Pull scissors with 50 mm pull eye and height adjustment * Tool box made of galvanized sheet steel, black powder-coated, approx. 1,000 mm wide, 600 mm deep, 300 mm high * Front section in front of the bogie platform approx. 490 mm long with 45° corners * ROBOT welded ANTI-SLIP coating for the steel plate of the bogie platform * La-Si package consisting of: in front of the front wall support on the left & right 1 x 13.4 ton each. UVV lashing eye, 4 holes on each side in the bogie platform with a lashing force of 2 tons each, 1 pair of lashing eyes (13.4 tons) hanging at the rear left and right in front of the rear carrier, 4 pairs of UVV lashing rings (10 tons) on each side, can be swiveled and lowered, can be loaded in all directions and embedded in the outer frame, 3 stake pockets on each side with a simultaneous 2 ton lashing option * Hot-dip galvanized mechanical folding boom for a total width of 3 meters (but not in the rear slope) * Plank holder for widening under the chassis on the left in the longitudinal direction * Excavator boom storage above the rear axle to the end carrier approx. 2,100 mm long and approx. 190 mm deep, 2 pairs of 6.4 tons on each side. Lashing rings in the excavator boom storage * Hardwood floor on the running surfaces of the low-loading platform * Hydraulic one-piece ramps (approx. 3,000 x 720 mm) mechanically laterally adjustable * Outer planks of the ramps made of hardwood * Steel construction in preparation for 6-way control slide * Loading edge unloaded approx. 950 mm +/+ 20 mm chassis * Bogie, folding boom, mechanical drop supports, ramps hot-dip galvanized * --Axles, air tank, pull scissors painted in a black tone-- * Tires 235/75 R 17.5 * Vehicle has a daily registration in 07/2024, due to missing tire pressure monitoring system and has not been loaded/used Knodpfx Abel Tlhrslsc * New vehicle with manufacturer's warranty * Errors and prior sale subject to reservation * Available for immediate delivery from Egestorf

Condition: new, overall weight: 14,400 kg, maximum load weight: 12,080 kg, axle configuration: 2 axles, loading space length: 3,900 mm, loading space width: 1,920 mm, loading space height: 415 mm, Year of construction: 2022, Equipment: ABS, tail-lift, * ETM-TA 14.4: * Wabco ABS braking system * Emergency release device for spring-loaded cylinders * Drum brakes, 2 x 7 tonnes. Gigant axles * Parabolic springs with tandem compensation unit * Height-adjustable drawbar (+/- 150 mm) with 40 mm screw drawbar eye * Jost support winch at the front, side impact protection * Foldable A-plate at the rear * 15-pin power plug, multi-chamber tail lights * Fixed steel front and side walls * Plug-in steel rear wall * Floor made of 50 mm softwood * 1 sliding plate support 750 x 1,000 mm in the front area including 2 trough stops at the front that can be plugged into 2 positions * 4 reversible trough stops that can be plugged into 2 positions for laterally centering the troughs * 1 x (13.5 ton) UVV lashing ring on each side for hanging tensioning elements * 2 ratchet tensioners (spindle adjustment) with compensation chain and quick shortener (tension force 6,300 kg) * Rear cross member for attaching aluminum ramps including 2 additional rear fall supports * Loading edge unloaded approx. 710 mm * Chassis, bulkhead, side walls, fender, drawbar, rear fall supports hot-dip galvanized * the axles, springs, support winch, air tank painted in a black tone * Tires: 285/70R19.5, wheelbase: 1,140 mm * Loading edge unloaded: approx. 710 mm, sold without container * Color hot-dip galvanized Kedsq Euarspfx Ablenc * Vehicle has a daily registration in 06/2024, due to missing tire pressure monitoring system and has not been loaded/used * New vehicle with manufacturer warranty * Errors and prior sale subject to reservation * available immediately from Egestorf on the A7

Condition: new, overall weight: 19,000 kg, maximum load weight: 14,550 kg, axle configuration: 2 axles, loading space length: 6,270 mm, loading space width: 2,470 mm, loading space height: 400 mm, Year of construction: 2024, * ETÜ-TA-R 19.0: * Wabco EBS-E (electronic braking system) * RDÜ (tire pressure monitoring) * Emergency release device for spring-loaded cylinders * Drum brakes * 2 x 11 tonnes Gigant axles * Air suspension, drawbar with 50 mm flanged drawbar eye and height-adjustable drawbar * Jost landing gear at the front * External folding supports at the rear * Toolbox made of galvanized sheet steel, approx. 650 x 350 x 320 mm, on the right side (powder-coated in black) * Side impact protection * Plastic quarter fender * 15-pin power connector Kedpfxopk D D He Abljnc * LED taillights * Reinforcement package for drilling rig transport on the chassis - loading height + 20 mm * 50 mm clamped softwood floor * Device for retrofitting container locks in front of the bulkhead * Bolted bulkhead made of smooth sheet steel * Trapezoidal profiled sheet steel side walls, foldable with side wall spring jack * Steel rear wall retractable between the ramps - bracket inside in front of the bulkhead when not in use * Bolted rear stanchions * Perforated Outer frame angled at approximately 45 degrees with a 2-ton lashing capacity every 480 mm * Installation of 3-ton drop lashing brackets possible every 600 mm * 1 x 10-ton lashing ring in each of the front and rear corners, various holes in the front and end beams for 1.2-ton lashing capacity * One-piece mechanical Grating loading ramps with spring mechanism for one-person operation, approx. 2,750 x 620 mm (can be collapsed to within 20 mm) * Rear approach slope approx. 860 mm * Chassis, drawbar, bulkhead, tailgate, rear folding supports, and loading ramps hot-dip galvanized * Axles, springs, air chamber, and landing gear painted in a single black tone * Wheelbase: 1,310 mm * Tires: 235/75R17.5 * Side walls painted in RAL 9010 pure white * Side walls painted in a single RAL color available for an additional charge * New vehicle with manufacturer's warranty * Errors and prior sale subject to change * Available for immediate delivery from Egestorf

Condition: new, overall weight: 14,400 kg, maximum load weight: 10,750 kg, axle configuration: 2 axles, loading space length: 7,000 mm, loading space width: 2,470 mm, loading space height: 400 mm, Year of construction: 2025, * ETÜ-TA-R 14.4: * RDÜ tire pressure monitoring * EBS brake system * Emergency release device for spring-loaded cylinders * Drum brakes * 2 x 7 tonnes Gigant axles * Parabolic springs with compensating unit * Drawbar height adjustable by 300 mm - Drawbar extension by 250 mm to 2,250 mm * 15-pin power connector * LED lighting * Front landing gear * External folding supports at the rear * Plastic toolbox approx. 858 x 500 x 500 mm, front right outside on the bulkhead * Side impact protection * Plastic quarter fenders * 50 mm softwood floor * In front of the bulkhead and rear slope, provision for retrofitting container locks for transporting 20" containers * Bolted bulkhead made of smooth sheet metal * Trapezoidal sheet steel side walls, foldable, split in the middle once * Steel rear wall can be inserted between the ramp brackets when not in use * Bolted rear stanchions * Perforated outer frame Approx. 45-degree canted with a 2-ton lashing capacity every 480 mm, installation of 3-ton drop lashing rings possible every 600 mm, 1 x 6.3-ton lashing ring in each of the front and rear corners, various holes in the front and end beams for 1.2-ton lashing capacity * One-piece mechanical grating loading ramps with spring mechanism for one-person operation, approx. 2,750 x 600 mm (collapsible up to 20 mm) * Rear approach slope approx. 860 mm chassis Kodpfxsv Eq Evo Abljnc * Drawbar, front wall, tailgate, folding supports, and loading ramps hot-dip galvanized * Axles, springs, air chamber, flanged drawbar eye, and landing gear painted in a single black tone -- * Reinforced and certified body according to EN 12642 XL including load securing certificate-- * Wheelbase 1,140 * Side walls painted in black RAL 9010 pure white * Side panels can be painted in a RAL color for an additional charge * New vehicle with manufacturer's warranty * Errors and prior sale subject to change * Available for immediate delivery from Egestorf

Condition: new, overall weight: 11,900 kg, maximum load weight: 8,870 kg, axle configuration: 2 axles, loading space length: 6,270 mm, loading space width: 2,470 mm, loading space height: 400 mm, Year of construction: 2025, * ETÜ-TA-R 11.9: * Loading area 6.27 m * Suitable for container transport * RDÜ tire pressure monitoring * EBS braking system * Emergency release device for spring-loaded cylinders * Drum brakes, 2 x 5.5 tonnes. BPW axles * Parabolic springs with compensating unit * Drawbar height adjustable by 300 mm Kjdpfxeq Ra D Ej Ablsnc * Jost landing gear at the front * External hot-dip galvanized folding supports at the rear * Plastic quarter fenders * LED lighting * Hot-dip galvanized chassis, drawbar, bulkhead, rear wall, rear stanchions, and loading ramps * 50 mm softwood floor * Device for retrofitting container locks in front of the bulkhead * Bolted smooth sheet metal bulkhead * Foldable trapezoidal steel side walls with side wall spring lifter * Steel rear wall can be inserted between the ramp brackets when not in use, inside the bulkhead * Bolted rear stanchions * Perforated outer frame, angled at approximately 45 degrees with a 2-ton lashing capacity every 480 mm * Installation of 3-ton Drop lashing rings available every 600 mm * 1 x 6.3 ton lashing ring in each of the front and rear corners * Various holes in the front and end beams for 1.2 ton lashing options * One-piece mechanical loading ramps with spring mechanism for one-person operation, approx. 2,750 x 600 mm (can be collapsed to within 20 mm) * Rear approach slope approx. 860 mm * Wheelbase: 990 mm * Tires: 235/75R17.5 * Side walls painted in RAL 9010 pure white * Side walls painted in a RAL color available for an additional charge * Plastic toolbox * Subject to errors and prior sale * Available for immediate delivery from Egestorf

Condition: new, overall weight: 30,000 kg, maximum load weight: 23,700 kg, axle configuration: 3 axles, * T3 Profi 30.0: * Wabco EBS-E (electronic braking system) * RDÜ tire pressure monitoring * Emergency release device for spring-loaded cylinders * Drum brakes * 3 x 11 ton BPW Eco axles * Air suspension with manual lowering at the rear Ksdpfjl Tpwyox Ablonc * Pressure gauge pressure display for determining the load weight (axles separated into 2 air suspension circuits), * Side impact protection * Swivel supports at the rear of the chassis frame * Mechanically adjustable warning sign packages at the front and rear * Front axle closed. Plastic fenders and rear straight galvanized sheet steel aprons, each with splash guard * Reflective contour tape on the side and rear * Hinged lid (hot-dip galvanized) for the toolbox in the bogie platform * LED tail lights * Rotating beacon (removable) at the rear * Pull scissors with 40 mm pull eye and height adjustment via tension spring & turnbuckle * 2 x 7-pin power plugs * 4 stake pockets on each side with simultaneous 2 ton lashing option * La-Si package consisting of: 2 lashing eyes (6.4 ton) at the front left & right on the main frame of the bogie platform, 5 pairs of UVV lashing rings that can be swiveled and lowered, can be loaded in all directions and are embedded in the outer frame - 13.4 ton in the corners, otherwise 10 ton * 6 pairs of mechanical folding booms for 3 mtr. Total width (but not in the rear slope) * Widening planks placed in the middle of the loading area * hydr. one-piece loading ramps (approx. 3,000 x 720 mm) laterally adjustable * Loading area above the turntable: approx. 1,960 x 2,520 mm * Loading height unloaded approx. 1,070 mm * Rear loading area: approx. 6,500 x 2,520 mm * Loading height unloaded approx. 910 mm (incl. 860 mm approach slope) * Chassis, bogie, drawbar, folding extensions & loading ramps hot-dip galvanized * Axles, turntable, air tank etc. painted in a black tone * Tires 235/75 R 17.5 * Payload approx. 24,000 kg with 30,000 kg total weight * New vehicle with manufacturer's warranty * Errors and prior sale subject to change * Available for immediate delivery from Egestorf

Condition: new, overall weight: 14,400 kg, maximum load weight: 10,360 kg, axle configuration: 2 axles, loading space length: 6,270 mm, loading space width: 2,470 mm, loading space height: 400 mm, Year of construction: 2025, * ETÜ-TA-ER 14.4: * RDÜ (tire pressure monitoring with display option in the truck via EBS signal without truck-side installation) * Electronic braking system EBS * Emergency release device for spring-loaded cylinders Knsdpfx Aspk D Dqeblec * Drum brakes * 2 x 5.5 tonnes Gigant axles * Air suspension with lifting and lowering system * Drawbar height adjustable by 300 mm * Jost landing gear at the front * External hot-dip galvanized folding supports at the rear * Plastic toolbox at the front right, outside the bulkhead * Side impact protection * Plastic quarter fenders * LED lighting system * 15-pin power connector * Hot-dip galvanized chassis, drawbar, bulkhead, and rear wall * 50 mm softwood floor * Provision for retrofitting 20" counterlocks at the front and rear * Bolted smooth sheet metal bulkhead * Trapezoidal steel sheet sidewalls, foldable with side wall spring jack * Bolted hot-dip galvanized rear stanchions * Perforated outer frame, angled at approximately 45 degrees, with a 2-ton lashing capacity every 480 mm, installation of 3-ton drop lashing brackets every 600 mm possible, 1 x 6.3 ton lashing ring in each of the front and rear corners, various holes in the front and end beams for 1.2 ton lashing options * 1 pair of aluminum loading ramps approx. 3,310 x 400 mm (load capacity 8 tonnes per pair) suitable for rubber-tired and tracked vehicles. Storage compartment recessed into the chassis below the loading area from the rear. * Vehicle hot-dip galvanized * New vehicle with manufacturer's warranty * Errors and prior sale subject to change * Available for immediate delivery from Egestorf

Condition: new, overall weight: 18,000 kg, maximum load weight: 14,660 kg, axle configuration: 2 axles, loading space length: 6,270 mm, loading space width: 2,470 mm, loading space height: 400 mm, Year of construction: 2025, * ETÜ-TA-R 19.0: * Wabco EBS braking system * RDÜ tire pressure monitoring system * Emergency release device for spring brake cylinders * Drum brakes * 2 x 10 t BPW Eco axles * Parabolic springs - 110 mm wide - with tandem compensation unit * Drawbar with 50 mm flange towing eye and height-adjustable drawbar * Jost landing gear at the front * External folding supports at the rear * Lateral underrun protection * Plastic quarter mudguards * 15-pin electrical connector * LED tail lights * 50 mm softwood floor * Fixture in front of the bulkhead for retrofitting container locks * Bolted bulkhead made of smooth sheet metal * Trapezoidal-profiled steel side walls, foldable with tailgate spring assist * Rear steel wall, retractable between the ramps – with internal holder at the front bulkhead when not in use * Bolted rear stanchions * Perforated external frame, bent at approximately 45 degrees, with 2 t lashing capacity every 480 mm * Option to install 3 t folding lashing rings every 600 mm * One 10 t lashing ring in each front and rear corner, various holes in the bulkhead and rear cross member for 1.2 t lashing options * One-piece mechanical grating ramps with spring mechanism for single-person operation, approx. 2,750 x 620 mm (retractable to 20 mm) * Ramp gradient at the rear approx. 860 mm * Chassis, drawbar, bulkhead, rear wall, ramps, and folding supports hot-dip galvanized * Side wall coating in RAL 9010 pure white * Other RAL color options for side walls available at extra cost Kjdpfxsl Th Hwj Ablsnc * Axles, springs, air tanks, flange towing eye, and landing gear painted in black * New vehicle with full manufacturer's warranty * Errors and prior sale reserved * Immediately available from Egestorf

Condition: new, overall weight: 11,900 kg, maximum load weight: 8,800 kg, axle configuration: 2 axles, loading space length: 5,370 mm, loading space width: 2,470 mm, loading space height: 400 mm, Year of construction: 2025, * ETÜ-TA-R 11.9: * Loading area 5.37 m * TPMS (Tire Pressure Monitoring System) * EBS braking system * Emergency release device for spring brake cylinders * Drum brakes, 2 x 5.5 t Gigant axles Knsdjl Th Nrjpfx Ablec * Parabolic springs with compensating unit * Height-adjustable drawbar by 300 mm * Jost landing leg at the front * External folding support legs at the rear * Plastic toolbox on the front right exterior of the front wall * Side underrun protection * LED lighting * Plastic quarter mudguards * 50 mm softwood floor * Bolted smooth sheet metal front wall * Drop-down trapezoidal steel side walls with sideboard-lifting spring * Steel rear wall can be slid in between ramp holders when not in use, stored inside in front of the front wall * Bolted rear stakes * Perforated outer frame approx. 45-degree angled with 2 t lashing capacity every 480 mm * Installation of 3 t drop lashing rings possible every 600 mm * Each front and rear corner with 1 x 6.3 t lashing ring * Various boreholes in the front and rear cross members for 1.2 t lashing possibilities * One-piece mechanical grid ramps with spring mechanism for single-person operation approx. 2,750 x 600 mm (can be pushed together to 20 mm) * Rear approach angle approx. 860 mm chassis * Drawbar, front wall, tailgate, folding supports, and ramps hot-dip galvanized * Axles, springs, air tanks, and 40 mm flanged towing eye painted in black * Wheelbase: 990 mm * Tyres 235/75R17.5 * Sideboard paintwork in RAL2011 deep orange * Side wall painting in RAL color available at extra charge * New vehicle with manufacturer's warranty * Errors and prior sale reserved * Available for immediate delivery from Egestorf

Condition: new, axle configuration: 2 axles, overall weight: 18,000 kg, maximum load weight: 14,650 kg, Year of construction: 2024, * RS-T 18.0 / 018: * Wabco EBS-E (electronic braking system) * RDÜ tire pressure monitoring * Emergency release device for spring-loaded cylinders * Disc brakes * Duomatic brake connection * 2 x 10 ton SAF axles * Air suspension with automatic lowering when the brake is uncoupled * Pull scissors 2,300 mm long with 40 mm towing eye and height adjustment via tension spring & spindle * Plastic tool box on the right side, closed. Plastic fenders * closed side impact protection as advertising space * underrun protection with 2 impact buffers * foldable A-sign at the rear for waste disposal * LED tail lights with protective roof * 2 x 7-pin power plugs * hot-dip galvanized chassis (without air tank, axles, pull scissors, etc.) * roller track length approx. 6,950 mm * roller container is clamped by pneumatic 4-way claw locking * there are 2 plug-in container stops at the front with 2 additional plug-in positions Knjdpfx Ael Tpy Hsbljc * driving height unloaded approx. 1,165 mm * -- permissible total weight of 20,000 kg technically possible-- * suitable for 5,000 - 7,000 mm container lengths * new vehicle with manufacturer's warranty * errors and prior sale subject to reservation * available immediately from Egestorf

Condition: new, axle configuration: 2 axles, overall weight: 21,000 kg, maximum load weight: 16,500 kg, loading space length: 4,995 mm, loading space width: 2,380 mm, loading space height: 1,000 mm, * KA-TA-R 21.0: * Chassis in black (not galvanized) * 2 axle tandem agricultural * Steel 3 side tipper. with Bordmatik * EBS (electrical braking system with RSS) * RDÜ tire control monitoring system * Emergency release device for spring-loaded cylinders * Drum brakes * Gigant axles * Air suspension with level control during tipping * Starting aid for maneuvering purposes on the 1st axle (switched via EBS) * Support winch at the front * EBS multi-voltage system for towing vehicles with 12 & 24V electrics * 13-pin 12V power plug * Drawbar with ball head coupling K80 (adjustable mm coupling height approx. 440 - 550 mm loaded) with raised gallows for connecting cables * Bolted steel underrun protection Knodpfx Absv D Tb Rjloc * Plastic quarter fenders in front of the first and after the last axle * Chassis made of fine-grain steel * Steel 3-side tipping structure, fixed front wall, continuous side walls - without center stanchions -, right side wall swings via central locking and folds down with Side wall spring lift, left side wall foldable with side wall hydromatics, tailgate swings via automatic hook lock * 5mm sheet steel floor made of HARDOX-450 steel or equivalent * 4 x 3 ton UVV lashing rings embedded in the outer frame on each side, * Support load 3 ton * Tires 600/55/R22.5 * New vehicle with manufacturer's warranty * Errors and prior sale subject to change * Delivery time on request

Condition: new, axle configuration: 2 axles, overall weight: 14,400 kg, maximum load weight: 12,080 kg, loading space length: 3,900 mm, loading space width: 1,920 mm, loading space height: 415 mm, Year of construction: 2022, Equipment: ABS, * ETM-TA 14.4: * Wabco ABS braking system * Emergency release device for spring-loaded cylinders * Drum brakes, 2 x 7 tonnes. Gigant axles * Parabolic springs with tandem compensation unit * Height-adjustable drawbar (+/- 150 mm) with 40 mm screw drawbar eye * Jost support winch at the front, side impact protection * Foldable A-plate at the rear * 15-pin power plug, multi-chamber tail lights * Fixed steel front and side walls * Plug-in steel rear wall * Floor made of 50 mm softwood * 1 sliding plate support 750 x 1,000 mm in the front area including 2 trough stops at the front that can be plugged into 2 positions * 4 reversible trough stops that can be plugged into 2 positions for laterally centering the troughs * 1 x (13.5 ton) UVV lashing ring on each side for hanging tensioning elements * 2 ratchet tensioners (spindle adjustment) with compensation chain and quick shortener (tension force 6,300 kg) * Rear cross member for attaching aluminum ramps including 2 additional rear fall supports * Loading edge unloaded approx. 710 mm * Chassis, bulkhead, side walls, fender, drawbar, rear fall supports hot-dip galvanized * the axles, springs, support winch, air tank painted in a black tone * Tires: 285/70R19.5, wheelbase: 1,140 mm * Loading edge unloaded: approx. 710 mm, sold without container Knodpfxsl Th Dms Abljc * Color hot-dip galvanized * Vehicle has a daily registration in 06/2024, due to missing tire pressure monitoring system and has not been loaded/used * New vehicle with manufacturer warranty * Errors and prior sale subject to reservation * available immediately from Egestorf on the A7