Used Faymonville Standard Body Trailers for sale (205)

Condition: new, empty load weight: 12,900 kg, maximum load weight: 34,100 kg, overall weight: 47,000 kg, axle configuration: 2 axles, loading space length: 6,850 mm, loading space width: 2,540 mm, loading space height: 350 mm, suspension: other, tire size: 245/70 R 17,5, color: grey, operation weight: 12,900 kg, Equipment: ABS, Gooseneck: -Gooseneck in SNT design to optimize the loading area length, length approx. 3,750 mm -Gooseneck can be raised/lowered hydraulically and removed -Technical fifth wheel load: 23,000 kg -For tractor units: 4 x 2, 6 x 2 and 6 x 4 Loading area: -Low bed with external supports in extendable "SUPER LOW" design, length approx. 6,850 mm -Low bed with solid hardwood floor approx. 40 mm thick and mechanical locking Rear chassis: -Rear chassis with closed external frame, checker plate covering and continuous prism excavator trough approx. 1,250/700 x 505 mm, open at the rear -2 pairs of lashing rings that can be folded outwards -1 pair of lashing rings lying in the trough -2 pairs of stake pockets for plug-in stakes 100 x 50 mm in the outer frame Pendulum axle and tires: -"PENDEL-AXLE", all axles hydromechanically forced steered -Hose rupture valve on the axle compensation cylinder with automatic RESET function -Hydraulic cylinder with shut-off valves and pins for securing in raised position -Final painting of axles with 2 layers of 2-component paint, painted in a single color in "FAY-Gray-34-0260" -Technical axle load: 12,000 kg -Hydraulic axle compensation -Tires 245/70 R 17.5 -TPMS tire pressure monitoring system in accordance with ECE R 141 Accessories: -Preparation for screw-on container positioning for 1x 20ft or 1x40ft container on the outer supports -2" kingpins -A galvanized steel front wall approx. 400 mm high -One spare wheel -Yellow-red air couplings on the galvanized connection strip at the front -4 wheel chocks -Steering from the front and rear can be operated using a cable remote control via push buttons, with alignment control of the axles -Hydraulic connections from the gooseneck to the low bed with multi-coupling instead of screw couplings -Electro-hydraulic unit -White reflector tape in accordance with EU regulations on the side, on the extension and at the rear -European reflector signs (red-yellow) on the rear of the trailer -One holder for the warning signs including a socket on the gooseneck and on the rear panel on the left and right -6 pairs of threaded blocks between the lashing rings under the top strap on the outer support for mounting screwable RUD rings VLBG-4 -ALU side walls and rear wall can be plugged into the gooseneck approx. 2,440 x 400 mm -The rear galvanized plug-in stanchions are removable (Length of the body approx. 2,560 mm) -Gooseneck in the rear upper area closed with a removable cover -5 pairs of stake pockets for 100 x 50 mm stakes in the outer frame of the loading area -Foldable extensions, approx. 230 mm per side -2 pairs of screwable RUD rings VLBG-4 M24 (LC 8,000 daN) Hsdpfxehlz R Se Aaaenk -1 pair of steel ramps to bridge the hooks of the low bed -A painted layer of sand on the loading area as anti-slip protection -Speed sticker 80 km/h at the rear and on both sides -Dipper handle recess of the rear chassis closed at the rear with a plug-in plate -Four warning signs extendable by approx. 400 mm, approx. 423 x 423 mm -Radio remote control for the steering in addition to the cable remote control, with indicator lights on the receiver as Alignment control -Central lubrication system with 2 BEKAMAX (Pico) pumps with NLGI-2 normal grease -Load pressure gauge for determining axle loads -HRM metallization (High Resistance Metallization) of the outer frame -Complete steel construction shot blasted, then the defined visible surfaces are hot-finished in metallization with ZINACOR 850 (zinc 85% - aluminum 15%)

Condition: new, empty load weight: 17,250 kg, maximum load weight: 48,700 kg, overall weight: 66,000 kg, axle configuration: 3 axles, loading space length: 7,550 mm, loading space width: 2,480 mm, loading space height: 375 mm, tire size: 245/70 R 17.5, color: grey, operation weight: 17,250 kg, Equipment: ABS, Gooseneck: -Gooseneck in SNT design to optimize the loading area length, length approx. 3,750 mm -Gooseneck can be raised/lowered and removed hydraulically -For tractor units: 6 x 4 and 8 x 4 (or 6 x 4 with optional 1-axle dolly) Low bed: -Low bed with external supports, designed as a telescopic tank bridge in low construction with extension at the front -Length x width approx. 7,550 mm x 2,740 mm -Mechanical locking of the extension Chassis: -Chassis at the rear with closed outer frame -Checker plate covering and continuous prism excavator trough approx. 1,450/900 x 505 mm, open at the rear Axles, suspension and tires: -"PENDEL-AXLE", all axles hydromechanically forced steering -Hose rupture valve on the axle compensation cylinder with automatic RESET function -Hydraulic cylinder with shut-off valves and pins for securing in raised position -Final painting of axles with 2 layers of 2-component paint in a single color in "FAY-Gray-34-0260" -Technical axle load 12,000 kg -Hydraulic axle compensation -245/70 R 17.5 Accessories: -Steel bulkhead, plug-in, approx. 400 mm high -4 wheel chocks -Gooseneck in the rear upper area closed with a removable cover -1 pair of steel ramps with climbing strips and fastening bolts to bridge the hooks of the low bed -The ramps can be placed over or between the hooks -Fastening options for the steel ramps at the rear between the outer supports of the gooseneck -One Locking point approximately every 1,000 mm on the extension Hedpoh Hm Tzefx Aaaenk -1 lashing ring on the left and right on the front cross member -Connection strip for supply lines to the tractor unit, attached at the height of the outer frame profile -6 pairs of threaded blocks on the outside of the inner supports of the loading area for mounting screwable rings M24 -6 pairs of countersunk lashing rings on the outside of the outer supports of the loading area, foldable inwards and outwards -1 pair of threaded blocks at the front and rear of the outer supports of the loading area for mounting screwable rings M24 -Hanging strip for loose aluminum loading ramps on the vehicle's end cross member -Central lubrication system with 2 pumps, BEKAMAX brand -Steering from the front and rear, operated by cable remote control, with alignment control of the axles -3 kW electro-hydraulic unit for controlling the hydraulic processes, with the exception of hydraulic cable winches -Removable loading floor (galvanized) in 3 elements can be inserted between the outer supports with hardwood flooring -Foldable extensions, by approx. 230 mm per side -Extension planks, loose, framed in steel -4 warning signs approx. 423 x 423 mm -Radio remote control for operating the steering -3.5" king pin -Anti-slip sticker on the left bevel of the gooseneck -Hydraulic connections from the gooseneck to the low bed with multi-coupling instead of screw couplings -Guide plate from the gooseneck for the fifth wheel plate, approx. 800 mm wide -1 spare wheel with mounting adapter -Parking position on the gooseneck for the warning signs when not in use -2 pairs of stake pockets embedded in the outer frame of the chassis, for plug-in stakes approx. 100 x 50 mm -Dipper handle recess of the rear chassis closed at the back with a plug-in plate -Color of the trailer MB 7350 Novagrau

Condition: new, maximum load weight: 49,000 kg, overall weight: 60,800 kg, axle configuration: > 3 axles, loading space length: 9,300 mm, loading space width: 2,540 mm, loading space height: 860 mm, suspension: air, tire size: 235/75 r 17.5, color: grey, Equipment: ABS, Gooseneck: -Gooseneck with beveled corners at the front 45° and with rear bevel of approx. 750 mm x 10° -3 pairs of lashing rings (LC 5,000 daN) -Hardwood decking 30 mm thick Loading area in extendable version: -Loading surface in extendable version with rear bevel of approx. 1,000 mm x 8° -5 pairs of lashing rings can be folded outwards (LC 5,000 daN) -3 pairs of lashing rings can be folded outwards (LC 10,000 daN) -1 pair of lashing rings lying in the front of the cargo bed (LC 10,000 daN) Cut-outs in the outer frame of the cargo bed for attaching lashing straps. (LC 2,000 daN) -Hardwood flooring approx. 48 mm thick, checker plate flooring over the axles Removable two-part ramps: -A pair of galvanized two-part steel ramps approx. 2,750 + 1,400 x 800 mm with approx. 48 mm thick hardwood decking -Ramp with hydraulically folding and unfolding ramp sections, hydraulic lifting gear and hydraulically movable -Maximum load per pair: 40,000 kg Seat posts: -JOST fifth wheels (mechanical) with 2-speed gearbox for 24 t lifting load (50 t test load) Axles and tires: -BPW axles, two axles rigid two axles self-steering, air-suspended, with drum brake, with lifting/lowering function The self-steering axles with electro-magnetic reverse lock can be activated via reverse gear or manually -axle tool -235/75 R 17.5 tires Brake system: -brake system in accordance with EU regulations with EBS-E (4S3M) Steel construction: -steel construction made of high-strength fine-grained steels -Steel grades: -S355J2+N/S355MC (yield strength 355MPa) -S690QL/S700MC (yield strength 690MPa) Coating: -First-class and durable corrosion protection of the standard shot-peened welded frame guaranteed by a 2-component (2K) zinc dust primer A high-quality 2-component (2K) top coat in a single color in nova grey Electrical system: -Electrical system in accordance with EU regulations, 24 volt ASPÖCK-NORDIK lighting (ASS3) Hedpfxoh Etf Rj Aaaonk ASPÖCK-UNIBOX on the front connection strip with 24N, 24S & 15-pin sockets Accessories included: -2" kingpin -One galvanized steel bulkhead approx. 400 mm high -One spare wheel with holder in front of the bulkhead -Yellow-red air couplings on the galvanized connection strip at the front -4 wheel chocks with holder on the bulkhead -Mounting in the rear area of the gooseneck for ALU docking ramps -Galvanized folding supports under the bevel of the cargo bed -One bracket for a rotating beacon -Cover plates to bridge the gap between ramps and cargo bed -White reflector tape in accordance with EU regulations on the sides, on the extension and red at the rear -Electric hydraulic unit -On the gooseneck and on the ramps on the left and right a holder for the warning signs including socket -Control valves for the ramps mounted on the right-hand side of the trailer -One mud flap at the rear of the trailer -Manual and description on USB stick -ALU drop sides and rear wall can be plugged onto the gooseneck approx. 2,440 x 400 mm -The rear galvanized stanchions are removable (length of the body approx. 2,560 mm) -4 pairs of WADER container pockets in the loading area for one 20ft, 2x 20ft or one 40ft container -7 pairs of stanchion pockets for 100 x 50 mm stanchions in the outer frame of the cargo bed -Galvanized extensions, extendable by approx. 230 mm per side -Lift axle on the front axle with controls -Square climbing rails 20 x 20 mm -BEKAMAX central lubrication system -Four warning signs extendable by approx. 400 mm approx. 423 x 423 mm

Condition: new, empty load weight: 17,500 kg, maximum load weight: 43,500 kg, overall weight: 61,000 kg, axle configuration: 3 axles, loading space length: 7,550 mm, loading space width: 2,750 mm, loading space height: 400 mm, tire size: 245/70 R 17.5, color: grey, Equipment: ABS, Gooseneck: -Gooseneck in SNT design to optimize the loading area length, length approx. 3,750 mm -Gooseneck can be raised/lowered and lowered hydraulically -For tractor units: 6x4 or 8x4 Drop deck: -Low bed with external beams in extendable design, "SUPER LOW" design, length approx. 7,550 mm -Low bed with solid hardwood floor approx. 40 mm thick and mechanical locking mechanism The supply lines are protected in the pull-out supports and automatically adjust to the respective drop-down bed length Rear chassis: -Rear chassis with closed outer frame, checker plate covering and continuous Prisma excavator trough approx. 1,450/900 x 505 mm, open at the rear -2 pairs of stanchion pockets for 100 x 50 mm stanchions in the outer frame Axles and tires: -"PENDEL-AXLE", all axles with hydromechanical forced steering -Hose rupture valve on the axle compensation cylinder with automatic RESET function -Hydraulic cylinder with stopcocks and locking pin for securing in raised position -Technical axle load: 12,000 kg -Hydraulic axle compensation -245/70 R 17.5 / 3PMSF tires Accessories included: -Preparation for mounting bolt-on container positioners for 1x 20ft or 1x 40ft container on the outer beams -2" kingpin -One galvanized steel end wall approx. 400 mm high -One spare wheel with holder -Yellow-red air couplings on the galvanized connection strip at the front -4 wheel chocks -Steering can be operated from the front and rear by remote control cable via pushbuttons, with axle tracking control -Hydraulic connections from the gooseneck to the low bed with multi-coupling instead of screw coupling -Electric hydraulic unit -White reflector tape in accordance with EU regulations on the side, on the extension and red at the rear -2 wooden blocks 500x250x200 mm -European reflector plates (red/yellow) at the rear of the trailer -On the gooseneck and on the rear plate on the left and right, one holder each for the warning signs including socket -Central lubrication system with 2 BEKAMAX (Pico) pumps with NLGI-2 standard grease -Load manometer for determining the axle loads including load diagram -ALU drop sides and rear wall can be plugged onto the gooseneck approx. 2,000 x 400 mm Hnsdpeh Hm Thefx Aaask -The rear galvanized stanchions are removable (length of the body approx. 2,120 mm) -Separate air connection with air gun on the gooseneck -Duomatic air coupling from gooseneck to low bed -Gooseneck closed in the rear upper area with a removable cover -1 pair of steel ramps for bridging the mounting hooks of the low bed -Four warning panels approx. 423 x 423 mm, extendable by approx. 400 mm -Radio remote control for steering in addition to the cable remote control, with indicator lights on the receiver for tracking control 6 pairs of threaded blocks between the lashing rings under the top chord on the outer beam for mounting screw-on RUD rings VLBG-4 -7 pairs of stanchion pockets for 100 x 50 mm stanchions in the outer frame of the cargo bed -folding extensions, approx. 230 mm on each side -A layer of sand painted onto the loading surface to prevent slipping Dipper arm recess of the rear chassis closed at the front and rear with a plug-in plate -HRM metallization (High Resistance Metallization) of the outer frame -Complete steel construction shot-blasted, then the defined visible surfaces hot-finished with ZINACOR 850 metallization (zinc 85% - aluminium 15%)

Condition: new, empty load weight: 15,420 kg, maximum load weight: 61,080 kg, overall weight: 76,500 kg, axle configuration: > 3 axles, loading space length: 8,600 mm, loading space width: 2,540 mm, loading space height: 900 mm, tire size: 235/75/r17,5, color: grey, Equipment: ABS, Gooseneck: Gooseneck with rear bevel of approx. 750 mm x 10° 3 pairs of lashing rings Hardwood decking 30 mm thick Loading platform: Loading area in extendable design with rear bevel of approx. 500 mm x 8° 8 pairs of lashing rings can be folded outwards 1 pair of lashing rings lying in the front of the cargo bed Cut-outs in the outer frame of the cargo bed for attaching lashing straps Hardwood flooring approx. 48 mm thick, checker plate flooring over the axles Two-part steel ramps: A pair of galvanized two-part steel ramps approx. 2,750 + 1,400 x 800 mm with approx. 48 mm thick hardwood decking. Ramp with hydraulically folding and unfolding ramp sections, hydraulic lifting gear and hydraulically movable. Maximum load per pair: 50,000 kg. Seat posts: - JOST fifth wheels (mechanical) with 2-speed gearbox for 24t lifting load (50t test load). Axles and tires: BPW axles and suspension, 4th + 5th axle self-steering Technical axle load: 12,000 kg 4th and 5th axles with electro-magnetic reverse lock via reverse gear and manual activation Tires 235/75 R 17.5 3PMSF Brake system: Brake system in accordance with EU regulations with EBS-E (4S3M) Sockets and lighting: Electrical system in accordance with EU regulations, 24 volt lighting ASPÖCK-NORDIK (ASS3) ASPÖCK-UNIBOX on the front connection strip with 24N, 24S & 15-pin sockets Connection according to ISO 24N ISO-1185 24S ISO-3731 15 pole ISO-12098 Paint finish: First-class and durable corrosion protection of the standard shot-peened welded frame guaranteed by a 2-component (2K) zinc dust primer A high-quality 2-component (2K) top coat in a single color in MB 7350 nova grey Rear section metallized and painted in RAL 9010 (pure white) No metallic paint finish possible Steel construction: Steel construction made from high-strength fine-grained steels Steel grades: S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa) Accessories: One spare wheel with holder in front of the bulkhead 2" kingpin One galvanized steel bulkhead approx. 400 mm high Hnodpjl Sl Izsfx Aaask Yellow-red air couplings on the galvanized connection strip at the front 2 restraining shoes with holder on the bulkhead Mounting in the rear area of the gooseneck for ALU docking lights A bracket for a rotating beacon at the rear of the trailer Galvanized supports under the bevel of the loading area White reflective tape in accordance with EU regulations on the sides, on the extension and red at the rear Electro-hydraulic unit at the rear under the cargo bed A holder for the warning signs, including a socket, on the gooseneck and on the rear panel on the left and right respectively Control valves for the ramps mounted on the right-hand side of the trailer A mud flap at the rear of the trailer Manual and description on USB stick 3.5" kingpin supplied loose ALU drop sides and rear wall can be plugged onto the gooseneck approx. 2,440 x 400 mm (LxH) The rear galvanized stanchions are removable (length of the body approx. 2,560 mm) 3 pairs of WADER container pockets in the loading area for a 20' (30') or a 40' container 6 pairs of stanchion pockets for 100 x 50 mm stanchions in the outer frame of the cargo bed Galvanized extensions, extendable by approx. 230 mm per side Lift axle on the front axle with control by TEBS E depending on the current axle load and the current load status Square climbing rails 20 x 20 mm every 200 mm on the outer frame of the loading area slope On the chequer plates, above the kingpin and the load floor

Condition: new, empty load weight: 9,500 kg, maximum load weight: 35,500 kg, overall weight: 45,000 kg, axle configuration: 3 axles, loading space length: 13,500 mm, loading space width: 2,540 mm, suspension: air, tire size: 435/50 R 19.5, color: grey, operation weight: 9,500 kg, Equipment: ABS, Extendable loading area: Loading area with hardwood planks with rear slope of approx. 1,000 mm x 8°    1 pair of permanently installed wheel recesses, approx. 1,610 x 970 x 400 mm     2 pairs of lashing rings (LC 5,000 daN)    Hnodpfx Aaek Eammoaok 1 pair of lashing rings (LC 10,000 daN)    6 pairs of lashing rings that can be folded outwards (LC 5,000 daN)    2 pairs of lashing rings that can be folded outwards (LC 10,000 daN)    Cut-outs in the outer frame of the loading area for attaching tensioning straps. (LC 2,000 daN)     Braking system:    Braking system in accordance with EU regulations with EBS-E (2S2M) Painting:    First-class and long-lasting corrosion protection of the standard shot-blasted welded frame guaranteed by a 2-component (2K) zinc dust primer     A high-quality 2-component (2K) top coat in a single color in Nova gray Rear section metallized and painted in RAL 9010 (pure white)     No metallic painting possible     Seatposts:     JOST seatposts (mechanical) with 2-speed gearbox for 24t lifting load (50t test load)     Steel construction:     Steel construction made of high-strength fine-grain steels     Steel qualities:     S355J2+N/S355MC (yield point 355MPa)    S690QL/S700MC (yield point 690MPa)    Electrical system:    Electrical system in accordance with EU regulations, lighting 24 volts    Sockets 24N, 24S & 15-pin    Axles and tires:    BPW axles, air-suspended, with disc brakes (377 mm), with lifting/lowering function    The self-steering axles with electromagnetic reversing lock can be activated via reverse gear or manually    Axle tool    Tires 435/50 R 19.5    Accessories included:    Yellow-red air couplings on the galvanized connection strip at the front    4 wheel chocks with brackets    2" kingpins    A galvanized steel bulkhead approx. 1600 mm high. EN12642-XL    White reflective tape in accordance with EU regulations on the side, on the extension and at the rear Red    Loading area with strong hardwood floor    9 pairs of stake pockets for 100 x 50 mm stakes in the outer frame of the loading area    1 spare wheel holder under the loading area on the right in the direction of travel    Galvanized folding supports under the slope of the loading area    Sliding hanging rails for aluminum loading ramps at the rear of the vehicle    European reflector signs (red-yellow) at the rear of the trailer    A mud flap at the rear of the trailer    A bracket for a rotating beacon at the rear of the trailer    On the gooseneck and on the rear panel on the left and right, a bracket for the warning signs including a socket    A tool box HDPE 620x360x610 under the loading area on the left in the direction of travel    4 pairs of WADER container pockets in the loading area, for 1x 20ft container or 1 x 40ft container, an additional locking point is provided in the extension for a 45ft container 3 pairs of stake pocket strips, mounted transversely in the loading area, for 100 x 50 mm stakes Lift axle on the front axle with control by TEBS E depending on the current axle load and the current loading condition Speed sticker 80 km/h at the rear and on both sides Four warning signs extendable by approx. 400 mm, approx. 423 x 423 mm with an LED position light. A holder for a rotating beacon on the warning signs Load gauge for determining the axle loads including load diagram HRM metallization (high resistance metallization) of the outer frame Complete steel construction shot blasted, then the defined visible areas in metallization

Condition: new, empty load weight: 10,600 kg, maximum load weight: 35,400 kg, overall weight: 45,000 kg, axle configuration: 3 axles, loading space length: 13,500 mm, loading space width: 2,540 mm, loading space height: 940 mm, suspension: air, tire size: 235/75 R 17,5, color: grey, Equipment: ABS, Loading area: -Loading area in extendable design -Loading area with hardwood planks with rear bevel of approx. 500 mm x 8° -2 pairs of lashing rings (LC 5,000 daN) -1 pair of lashing rings (LC 10,000 daN) -6 pairs of lashing rings that can be folded outwards (LC 5,000 daN) -3 pairs of lashing rings that can be folded outwards (LC 10,000 daN) -Cutouts in the outer frame of the loading area for attaching tensioning straps Braking system: -Braking system in accordance with EU regulations with EBS-E (2S2M) Paintwork: -First-class and long-lasting corrosion protection of the standard shot-blasted welded frame guaranteed by a 2-component (2K) zinc dust primer -A high-quality 2-component (2K) top coat in a single color in Nova gray -Rear section metallized and in Painted RAL 9010 (pure white) -No metallic paint possible Seatposts: -JOST seatposts (mechanical) with 2-speed gearbox for 24t lifting load (50t test load) Steel construction: -Steel construction made of high-strength fine-grain steel -Steel grades: -S355J2+N/S355MC (yield strength 355MPa) -S690QL/S700MC (yield strength 690MPa) Electrical system: -Electrical system in accordance with EU regulations, LED lighting 24 volts Hnedpfx Aol Ux Rwjaaok -2x 7-pin & 15-pin sockets Axles and tires: -BPW axles, air-sprung, with disc brakes (377 mm), with lifting/lowering function -Hydro-mechanical forced steering -Axle tool -Twin tires 235/75 R 17.5 Accessories included: -Yellow-red air couplings on the galvanized connection strip at the front -4 wheel chocks with bracket -2" king pins -A galvanized steel front wall approx. 1600 mm high -White reflector tape in accordance with EU regulations on the side, on the extension and red at the rear -Loading area with strong hardwood floor -Steering from the front and rear using a cable -Remote control operated via push buttons, with alignment control of the axles -With radio remote control for the steering -9 pairs of stake pockets for 100 x 50 mm stakes in the outer frame of the loading area. -Galvanized folding supports under the slope of the loading area -Movable mounting rail for aluminum docking ramps at the rear of the vehicle -European reflector signs (red-yellow) at the rear of the trailer -A mud flap at the rear of the trailer -A bracket for a rotating beacon at the rear of the trailer -A bracket for the warning signs including a socket on the gooseneck and on the rear panel on the left and right -A tool box INOX 1,500x390x810 under the loading area on the right in the direction of travel -Central lubrication system BEKAMAX (Pico) with normal grease NLHI-2 and removable protection around the pump -6 pairs of WADER container pockets in the loading area, for 1x 20ft container, 2 x 20ft container or 1 x 40ft container, an additional locking point is provided in the pull-out for a 45ft container -4 pairs Stake pocket strips, mounted transversely in the loading area, for 100 x 50 mm stakes -Lift axle on the front axle with control by TEBS -A dependency on the current axle load and the current loading status -Speed sticker 80 km/h at the rear and on both sides -Four warning signs extendable by approx. 400 mm, approx. 423 x 423 mm with an LED position light -A holder for a rotating beacon on the warning signs -Load pressure gauge for determining the axle loads including load diagram -HRM metallization (high resistance metallization) of the outer frame -Complete steel construction shot blasted, then the defined visible surfaces are hot-finished in metallization with ZIN

Condition: new, empty load weight: 11,300 kg, maximum load weight: 36,700 kg, overall weight: 48,000 kg, axle configuration: 3 axles, loading space length: 13,600 mm, loading space width: 2,540 mm, loading space height: 1,250 mm, suspension: air, tire size: 385/65 r 22,5, color: grey-black, Equipment: ABS, Cargo bed: Loading platform in extendable design with pneumatically operated locking mechanism There is an approx. 250 mm wide fixed intermediate table on the middle carrier 8 pairs of lashing rings can be folded outwards (LC 5,000 daN) 3 pairs of lashing rings can be folded outwards (LC 10,000 daN) Cut-outs in the outer frame of the cargo bed for attaching lashing straps (LC 2,000 daN) Axles and tires: BPW axles and suspension, all axles with hydro-mechanical forced steering Disc brakes, technical axle load: 10,000 kg Air suspension with lifting and lowering valve Axle tool 6-wheel tires 385/65 R 22.5 Brake system: Brake system in accordance with EU regulations with EBS-E (2S2M) Seat posts: JOST seat posts (mechanical) with 2-speed gearbox for 24 tons lifting load (50 tons test load) Steel construction: Steel construction made of high-strength fine-grained steels Steel grades: S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa) Electrical system: Electrical system in accordance with EU regulations, 24 volt lighting ASPÖCK-NORDIK (ASS3) ASPÖCK-UNIBOX on the front connection strip with 24N, 24S & 15-pin sockets Connection according to ISO: 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Paint finish: First-class and durable corrosion protection of the standard shot-peened welded frame guaranteed by a 2-component (2K) zinc dust primer A high-quality 2-component (2K) top coat in a single color in nova grey Rear section metallized and painted in RAL 9010 (pure white) No metallic paint finish possible Accessories included: A bracket for the warning signs on the gooseneck and on the rear panel on the left and right, including socket Re-steering can be operated from the front and rear using a cable remote control via pushbuttons, with toe-in control for the axles Electro-hydraulic unit Hnedpfx Aashlz Sheaok 4 wheel chocks with holder on the bulkhead 2" kingpin One galvanized steel bulkhead approx. 2,200 mm high Yellow-red air couplings on the galvanized connection strip at the front White reflector tape in accordance with EU regulations on the side, on the pull-out and at the rear Red European reflector plates (red/yellow) at the rear of the trailer A mud flap at the rear of the trailer Manual and description A bracket for a rotating beacon at the rear of the trailer Loading area with approx. 30 mm thick wooden floor edged in omega profiles 10 pairs of stanchion pockets for 100 x 50 mm stanchions in the outer frame of the cargo bed 1 spare wheel holder under the cargo bed on the right in the direction of travel 6 pairs of WADER container pockets in the cargo bed, for 1x 20ft container, 2x 20ft containers or 1x 40ft container, an additional locking point is provided in the pull-out for a 45ft container 5 pairs of stanchion pocket rails, mounted transversely in the loading area, for 100 x 50 mm stanchions One galvanized bracket transversely under the cargo bed (2,390 x 720 x 400 mm) Access ladder mounted on the right in the direction of travel One HDPE 1,200 x 500 x 480 mm toolbox at the front under the cargo bed on the left in the direction of travel Lift axle on the front axle with control by TEBS E depending on the current axle load and the current load status Central lubrication system with 2 BEKAMAX (Pico) pumps with NLGI-2 standard grease and removable protection around the pump Red/white reflective tape in the load platform extension A layer of sand painted onto the central beam to prevent slipping Radio remote control for the steer

Condition: new, empty load weight: 9,600 kg, maximum load weight: 53,400 kg, overall weight: 63,000 kg, axle configuration: > 3 axles, loading space length: 12,400 mm, loading space width: 2,540 mm, loading space height: 1,340 mm, suspension: air, tire size: 385/65 R22.5, color: grey, Equipment: ABS, Loading area: -Loading area with approx. 30 mm thick hardwood floor -10 pairs of lashing rings can be folded outwards Seat posts: Hnjdpsrq Dlfefx Aaaok -JOST seat posts with 2-speed gearbox for 24 t lifting load Axles and tires: -BPW axles, techn. 10,000 kg, first axle rigid, all other axles hydro-mechanically forced steered, mounted on turntable -Air-sprung with lifting and lowering valve -axle tool -385/65 R22.5 tires Brake system: -WABCO brake system in accordance with EU regulations with EBS-E (4S3M) Steel construction: -steel construction made of high-strength fine-grained steels -Steel grades: -S355J2+N/S355MC -S690QL/S700MC Electrical system: -Electrical system in accordance with EU regulations, 24 volt lighting -ASPÖCK UNIBOX on the front connection strip with 24N, 24S & 15-pin sockets Connection in accordance with ISO: 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Paintwork: -First-class and durable corrosion protection of the standard shot-blasted welded frame guaranteed by a 2-component zinc dust primer A high-quality 2-component top coat in a single color in nova grey -Rear part metallized and painted in RAL 9010 Accessories included: -Loading area with approx. 30 mm thick hardwood floor -2" kingpin -One galvanized steel end wall approx. 1,200 mm high EN12642-XL -Yellow-red air couplings on the galvanized connection strip at the front -4 restraining shoes with holder on the front wall -Storage for 1,000 mm stanchions in the rear central support -On the gooseneck and on the rear panel on the left and right, one bracket each for the warning signs including socket -Reverse steering can be operated from the front and rear via cable remote control using pushbuttons, with tracking control of the axles -Electric hydraulic unit -White reflective tape in accordance with EU regulations on the side of the trailer and red at the rear -12 pairs of stanchion pockets for 100 x 50 mm stanchions in the outer frame of the cargo bed -European reflector plates at the rear of the trailer -One bracket for a rotating beacon at the rear of the trailer -One mud flap at the rear of the trailer -Manual and description on USB stick -BEKAMAX (Pico) central lubrication system with NLGI-2 standard grease and removable protection around the pump -TPMS tire pressure monitoring system: -For correct display, the motor vehicle must be able to transmit and display this data -Lift axle on the front axle with control by TEBS E depending on the current axle load and the current load status -Radio remote control for steering in addition to the cable remote control, with indicator lights on the receiver for tracking control -5 pairs of stanchion pocket rails, mounted transversely in the cargo bed, for 100 x 50 mm stanchions -Speed stickers 80 km/h at the rear and on both sides -Adjustable access ladder mounted on the left and right in the direction of travel -2 reversing lights mounted on the rear panel -Load manometer for determining the axle loads including load diagram HRM metallization of the outer frame Complete steel construction shot-blasted, then the defined visible surfaces hot-finished in metallization with ZINACOR 850 (zinc 85% - aluminium 15%)

Condition: used, color: yellow, Year of construction: 2013,

Condition: used, empty load weight: 14,100 kg, maximum load weight: 33,900 kg, overall weight: 48,000 kg, axle configuration: > 3 axles, first registration: 11/1999, suspension: air, tire size: 235/75 17,5, tire condition: 50 %, color: green, Year of construction: 1999, front tire size: 235/75 17,5, rear tire size: 235/75 17,5, driver cabin: day cab, emission class: none, Equipment: truck registration, Reference number for inquiries: 68574 Hnsdpfxoyib Aho Aaaok Faymonville, Flatbed Trailer * Year of manufacture: 1999 * Air suspension * Steering axle * Forced-steered axle * Compressed air coupling head (red + yellow) * Connection plug: 2x7-pin * Lift and lower device * Extendable - telescopic semi-trailer * Suspension: Air * Gross vehicle weight: 48,000 kg * Unladen weight: 14,100 kg * Payload: 33,900 kg * Permissible total weight: 48,000 kg * Axle manufacturer: SAF * Tyre condition, 1st axle: 50% -- 50% - Tyre size: 235/75 R17.5 * Tyre condition, 2nd axle: 50% -- 50% - Tyre size: 235/75 R17.5 * Tyre condition, 3rd axle: 50% -- 50% - Tyre size: 235/75 R17.5 * Tyre size: 235/75 R17.5 * Manufacturer: ES-GE * Extension faulty * Steering axles not functional * Mobile Disclaimer: Subject to alterations, prior sale, and errors excepted. More photos and videos are available on our website. Our comprehensive services include, for example: * Purchase/sale/rental of commercial vehicles * Fast and hassle-free financing * Arranging all (export) documentation * Order of export/customs number plates * Vehicle preparation: new tarpaulins, lettering, painting, etc. * Professional loading and load securing * TÜV inspections, registration services * Transfer/transport of commercial vehicles Contact our trained staff for advice—we are happy to assist you.

Condition: new, maximum load weight: 30,190 kg, overall weight: 43,000 kg, axle configuration: 2 axles, Equipment: ABS, You can find our complete vehicle inventory, including immediately and short-term available vehicles, on our website. Extract from the equipment list. Full equipment details available on request. Loading Platform: - Lowbed with external beams in extendable SUPER LOW design, length approx. 6,850 mm - Lowbed with fixed hardwood floor approx. 40 mm thick and mechanical locking mechanism - Supply lines protected inside the extendable side rails, automatically adjusting to the current bed length - 5 pairs of lashing rings, foldable outward (LC 10,000 daN) - 6 pairs of threaded blocks on the inner beam for attaching RUD screw-on rings Gooseneck: - Gooseneck in SNT design for optimized platform length, length approx. 3,750 mm - Gooseneck hydraulically liftable/lowerable and detachable - Technical fifth wheel load: 23,000 kg - For tractors: 4x2, 6x2 Rear Chassis: - Rear chassis in short version with closed external frame and checker plate cover - Running gear with excavator recess, closed in the rear half to accommodate the air tanks - 2 pairs of lashing rings, foldable outward (LC 5,000 daN) - 1 pair of lashing rings, foldable outward (LC 10,000 daN) - 1 pair of lashing rings horizontal, front & rear of the chassis (LC 10,000 daN) Axles: - BPW axles, hydro-mechanically forced steering - Technical axle load per axle: 12,000 kg - Air suspension with lift and lower valve Tyres: - Tyres 245/70 R 17.5 3PMSF - Manufacturer of our choice - Load index (146/146F) - TPMS tyre pressure monitoring system in accordance with ECE R 141 - Data transmission to the truck via the standardized EBS interface in accordance with ISO 11992 - The truck must be capable of processing and displaying this data for correct operation Braking System: - Braking system according to EU regulations with EBS-E (2S2M) Electrical System: - Electrical system according to EU regulations, lighting 24 Volt ASPÖCK-NORDIK (ASS3) - All LED side marker lights flash with indicators - ASPÖCK-UNIBOX at the front connection point with 24N, 24S, and 15-pin sockets as per standards: - 24N ISO-1185 - 24S ISO-3731 - 15-pin ISO-12098 Steel Construction: - Steel construction from high-strength fine-grained steels - Steel grades: S355J2+N/S355MC (yield strength 355 MPa) S690QL/S700MC (yield strength 690 MPa) Paintwork: - Complete steel structure is automatically shot-blasted after welding using a blasting turbine system - Second blasting process with corundum for optimal adhesion of coating system - HRM metallization of complete chassis with ZINACOR 850 (85% zinc / 15% aluminum) to ensure maximum corrosion protection - Final paint finish with 2 coats of 2K topcoat, single color in RAL 3002 Carmine Red, as per RAL system 841GL - Rims in silver Hedpfsxarl Nsx Aaajnk - Rear section metallized and painted RAL 9010 (Pure White) - Metallic paint not possible - Paint system tested in salt spray test as per ISO 9227-NSS - Cavities sealed with special wax Including the following additional equipment: - 2" King pin - One galvanized steel front wall, approx. 400 mm high - Remote steering of front and rear axles by cable remote control with pushbuttons, including single track axle monitoring (without installation in the tractor unit) - Hydraulic connections from gooseneck to lowbed with multi-coupling instead of screw couplings - Electro-hydraulic power pack - Preparation for mounting container locks for 1x 20' or 1x 40' container on the external beams - Without container locks

Condition: new, maximum load weight: 45,820 kg, overall weight: 58,000 kg, axle configuration: > 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete range of vehicles, including those available for immediate or short-term delivery, on our website. Excerpt from the equipment list. Full equipment details available upon request. Gooseneck: * Gooseneck with front chamfered corners approx. 45° and rear bevel approx. 750 mm x 10° * 3 pairs of lashing rings (LC 5,000 daN) * Hardwood flooring approx. 30 mm thick Extendable loading platform: * Loading platform in extendable design with rear bevel approx. 1,000 mm x 8° Hsdpexbmpfofx Aaaenk * 5 pairs of fold-out lashing rings (LC 5,000 daN) * 3 pairs of fold-out lashing rings (LC 10,000 daN) * 1 pair of flush-mounted lashing rings at the front of the loading platform (LC 10,000 daN) * Cut-outs in the outer frame of the platform for attaching tie-down straps (LC 2,000 daN) * Hardwood flooring approx. 48 mm thick, over the axles with checker plate Axles: * BPW axles and suspension * 1st axle rigid, all other axles hydromechanically forced-steered * Technical axle load: 12,000 kg each * Air suspension with lifting and lowering valve * Axle tools Tyres: * 245/70 R 17.5 3PMSF tyres, load index (146/146 F) * Brand of our choice * TPMS tyre pressure monitoring system in accordance with ECE R 141 * Data transmission to the tractor unit via standardized EBS interface according to ISO 11992 * For correct display, the tractor unit must be able to transmit and display this data Landing legs: * JOST landing legs (mechanical) with 2-speed gearbox, approx. 24 t lifting load (approx. 50 t test load) Brake system: * Wabco brake system in accordance with EU regulations with EBS-E (4S3M), without connection lines to the tractor unit Paintwork: * Entire steel construction automatically blast cleaned after welding with shot blasting system * Second abrasive blasting with corundum for optimal adhesion of the coating system * Final coating with 2 layers of 2K topcoat, single color in RAL 3002 Carmine Red according to RAL system 841GL * Rims in silver grey * Rear section metallized and painted in RAL 9010 (Pure White) * Metallic paint not available * Paint system tested in salt spray test according to ISO 9227-NSS * Cavity sealing with special wax Steel construction: * Steel construction made from high-strength fine-grained steels * Steel grades: S355J2+N/S355MC (yield strength 355MPa), S690QL/S700MC (yield strength 690MPa) Electrical system: * Electrical system in accordance with EU regulations * 24 volt lighting ASPÖCK-NORDIK (ASS3) * All LED side marker lights flash with the indicator * ASPÖCK-UNIBOX at the front connection panel with 24N, 24S & 15-pin sockets in accordance with ISO * 24N ISO-1185, 24S ISO-3731, 15-pin ISO-12098 Including the following additional equipment: * 2 inch king pin * One galvanized steel front wall, approx. 400 mm high * Yellow-red air couplings on the galvanized connection panel at the front * Electro-hydraulic unit * Rear axle steering from both front and rear, operated via cable remote control with pushbuttons, including single-track control of the axles (without installation in the tractor) * Galvanized folding supports under the rear platform bevel * 1 pair of recessed lashing rings along the rear central beam in the bevel (LC 10,000 daN) * On the gooseneck, plug-in aluminum side walls and rear wall, approx. 2,440 x 400 mm (L x H) * The rear galvanized plug-in stanchions are removable. (Body length approx. 2,560 mm) * One galvanized toolbox integrated in the chamfered gooseneck * 3 pairs of WADER container locks in t

Condition: new, maximum load weight: 39,670 kg, overall weight: 50,960 kg, axle configuration: > 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete range of immediately and short-term available vehicles on our website. Extract from the equipment list. Full equipment details available on request. Gooseneck: * Gooseneck with hardwood flooring approx. 30 mm thick * Rear of gooseneck in straight design * 3 pairs of lashing rings (LC 5,000 daN) Loading Area: * Extendable loading area * 5 pairs of fold-out lashing rings to the outside (LC 5,000 daN) Hnodpfx Aasxarlvoask * 3 pairs of fold-out lashing rings to the outside (LC 10,000 daN) * 1 pair of recessed lashing rings at the front of the loading area (LC 10,000 daN) * Cutouts in the outer frame of the loading area for attaching tension straps (LC 2,000 daN) * Hardwood flooring approx. 48 mm thick, checker plate covering over the axles Landing Legs: JOST landing legs (mechanical) with 2-speed gearbox for approx. 24 t lifting capacity (approx. 50 t test load) Axles: * BPW axles, two rigid axles, two self-steering axles * Air suspension with lift/lower function * Self-steering axles with electromagnetic reverse lock, activated via reverse gear or manually * Drum brakes * Axle tool kit Tyres: * 205/65 R 17.5 * Brand of our choice * TPMS tyre pressure monitoring system according to ECE R 141 * Data transfer to the tractor unit via the standardised EBS interface as per ISO 11992 * For correct display, the tractor unit must be able to transmit and display these data Brake System: * Brake system in accordance with EU regulations with EBS-E (4S3M) without connection lines to the tractor unit Steel Structure: * Steel construction made of high-strength fine-grain steels * Steel grades: S355J2+N/S355MC (yield strength 355 MPa) S690QL/S700MC (yield strength 690 MPa) Paintwork: * Complete steel structure automatically blasted after welding using a shot blast system * Second blasting with corundum for optimal coating adhesion * HRM metallization of the entire chassis with ZINACOR 850 (85% zinc/15% aluminum) for best corrosion protection * Final coating with 2 x 2K topcoat, solid colour in RAL 3002 Carmine Red, according to RAL system 841GL * Wheels in silver * Rear section metallised and painted in RAL 9010 (Pure White) * Metallic paint not available * Paint finish tested with salt spray test according to ISO 9227-NSS * Cavities sealed with special wax Electrical System: * Electrical system in compliance with EU regulations, 24 Volt ASPÖCK-NORDIK (ASS3) lighting * All LED side marker lights blink together with the indicator * ASPÖCK-UNIBOX at the front connection strip with 24N, 24S & 15-pin sockets according to ISO; 24N ISO-1185, 24S ISO-3731, 15-pin ISO-12098 Accessories included: * 2-inch king pin * One spare wheel holder in front of the bulkhead * Yellow-red air couplings at the galvanised connection strip up front * Galvanised folding supports beneath the loading area bevel * One galvanised steel bulkhead (EN12642-XL), approx. 1,600 mm high * On the gooseneck, plug-in aluminium side and rear boards, approx. 2,440 x 400 mm (L x H) * The rear galvanised plug-in stanchions are removable (body length approx. 2,560 mm) * Support bracket with 1 pair of WADER container locks. Fifth-wheel load approx. 20,000 kg * 7 pairs of WADER container locks for 1x 20' container in the loading area * 1x 40' container in the loading area, 1x 40' container on the gooseneck, 2x 20' container * 7 pairs of stake pockets for 100 x 50 mm plug-in stanchions in the outer frame of the loading area * One galvanised bracket running across under...

Condition: new, maximum load weight: 36,360 kg, overall weight: 48,000 kg, axle configuration: 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete range of vehicles, including those available immediately or at short notice, on our website. Excerpt from the equipment list. Full equipment details available upon request. Gooseneck: * Gooseneck with front corners beveled approx. 45° and rear chamfer approx. 750 mm x 10° * 3 pairs of lashing rings (LC 5,000 daN) * Hardwood flooring approx. 30 mm thick Loading Platform: * Telescopic loading platform with rear slope approx. 1,000 mm x 8° * 1 pair of fixed wheel recesses in front of the axles, approx. 2,850 x 970 x 400 mm (L x W x D) * Wheel recesses with square climbing laths approx. 15 x 15 mm, including extensions at the bottom * Between the 1st and 2nd axle, one pair of fixed wheel recesses, approx. 1,610 x 970 x 400 mm (L x W x D) * Incl. 3-piece removable galvanized covers over the wheel recesses (width approx. 670 mm) – max. point load 5 t each * Recess in the slope and extending into the platform for accommodating an excavator dipper stick (approx. 2,900 x 750 x 210/290 mm (L x W x H)) * 1 pair of horizontal lashing rings at the front of the platform (LC 10,000 daN) * 5 pairs of fold-out lashing rings (LC 5,000 daN) * 2 pairs of fold-out lashing rings (LC 10,000 daN) * 2 pairs of lashing rings in the excavator stick recess (LC 5,000 daN) * Cut-outs in the platform's outer frame for attaching tie-down straps (LC 2,000 daN) Hnsdpfx Aeyhkq Ujaask Two-Piece Steel Ramps: * One pair of galvanized, two-piece steel ramps, approx. 2,750 + 1,400 x 800 mm, with approx. 48 mm thick hardwood covering * Ramps with hydraulically folding ramp sections and hydraulic lifting system, hydraulically adjustable * Maximum load per pair: 40,000 kg Landing Gear: JOST landing gear (mechanical) with 2-speed gearbox, lift capacity approx. 24 t (test load approx. 50 t) Axles: * BPW axles and suspension, 2 rigid axles, 1 trailing steering axle * Technical axle load: 12,000 kg each * Electromagnetic reverse lock, activated automatically by reverse gear and manually * Air suspension with lift and lower valve Tyres: * 235/75 R 17.5 3PMSF tyres – manufacturer of our choice TPMS: * TPMS tyre pressure monitoring system in accordance with ECE R 141 Brake System: * WABCO brake system according to EU regulations with EBS-E (2S2M) Paintwork: * HRM metallization of the entire vehicle chassis with ZINACOR 850 (85% zinc / 15% aluminum) for optimum corrosion protection * Final paintwork with two coats of 2K topcoat, solid RAL 3002 Carmine Red, in accordance with RAL System 841GL * Wheel rims in silver grey Incl. the following additional equipment: * 2-inch king pin * One galvanized steel front wall, approx. 400 mm high * 3 pairs of recessed lashing rings along the central beam (LC 5,000 daN) * Electro-hydraulic power unit at the rear, under the loading platform * On the gooseneck: plug-in aluminum drop sides and tail board, approx. 2,440 x 400 mm (L x H). The rear galvanized stakes are removable (body length approx. 2,560 mm). * One galvanized toolbox integrated in the gooseneck chamfer * 2 pairs of WADER container pockets on the loading platform for a 20' or 30' container * 3 pairs of stake pockets for plug-in stakes approx. 100 x 50 mm in the outer frame of the platform * 3 additional pairs of removable galvanized covers over the wheel recess – max. point load 3.5 t each * One removable galvanized intermediate table with 1 pair of WADER container pockets * 1 additional, hook-on intermediate table, approx. 300 mm wide * Intermediate table with offset load ar

Condition: new, maximum load weight: 51,780 kg, overall weight: 65,000 kg, axle configuration: > 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory, including immediately and short-term available units, on our website. Excerpt of Features. Full equipment list available upon request. GOOSENECK: * Gooseneck in SNT design for optimized loading platform length, approx. 3,700 mm in length, with rear bevel approx. 1,000 mm x 10° * For tractor units: 4 x 2, 6 x 2, and 6 x 4 * Plug-in steel bulkhead, approx. 400 mm high * ASPÖCK-UNIBOX on the front connector panel with 24N, 24S & 15-pin sockets * 3 kW electro-hydraulic power unit for hydraulic operations (excluding hydraulic winches) * Gooseneck outer beam with fixture boreholes for screw-in lashing rings * One mounting hole in the upper rear area of the gooseneck outer beam for a screw-in lashing ring * 1 pair of screw-in lashing rings included (LC 10,000 daN) * On the gooseneck: 1 pair of plug-in anodized aluminum side walls, approx. 400 mm high * On the gooseneck: 1 plug-in anodized aluminum rear wall, approx. 400 mm high * Heavy-duty hardwood flooring, approx. 40 mm over the gooseneck * 2-inch kingpin * 1 crosswise stake pocket rail in the gooseneck floor in front of the bevel, for plug-in stakes approx. 100 x 50 mm Hsdpfeyhkrlsx Aaaonk LOADING PLATFORM: * Extendable loading platform, approx. 8,800 mm long, with rear bevel approx. 500 mm x 10° * Recess in the loading platform, extending into the bevel, for excavator dipper stick, approx. 2,490 x 750 x 210/290 mm (L x W x H) * TPMS tire pressure monitoring system per ECE R 141 * BPW axles and suspension, 1st and 2nd axles fixed, 3rd and 4th axles steered * 3rd and 4th axles with electromagnetic reverse lock, activated via reverse gear and manually * Axle load capacity: 12,000 kg each, air suspension with raise/lower valve * Mechanical landing legs with 2-speed gearbox and crank * Hardwood flooring, approx. 50 mm thick, continuous and interrupted between axles (increases friction coefficient) * 1 intermediate table with recessed platform, approx. 300 mm wide, for the large-diameter extension tube with steel treadplate * 1 pair of lashing rings on the front cross-member (LC 10,000 daN) * 6 pairs of recessed, fold-out lashing rings in the outer frame (LC 10,000 daN) * Additional 1 pair of external lashing rings on the front cross-member, rotated approx. 90° towards the loading platform (LC 10,000 daN) * Extendable (galvanized) width extensions approx. 230 mm per side (without wood planks) * 1 pair of permanently installed open wheel recesses up to the extension, approx. 700 x 410 mm (W x D), in the deck ahead of the 1st axle * Between 2nd and 3rd axles, 1 pair of fixed wheel recesses approx. 1,695 x 700 x 410 mm (L x W x D) * 1 pair mechanical rear supports * 245/70 R 17.5 3PMSF twin tires – manufacturer of our choice HYDRAULIC LOADING RAMPS: * DR-15/60-900-4350-HB-HV-M * One pair of two-section steel ramps, approx. 4,350 mm long and 900 mm wide * Hardwood-covered hydraulically foldable ramp ends * Each ramp hydraulically adjustable approx. 235 mm outwards and 215 mm inwards * Hardwood decking on loading platform bevel * Ramps with hardwood overlay BRAKE SYSTEM: * WABCO EBS-E brake system compliant with EU regulations SURFACE TREATMENT: * HRM metallization of the entire chassis with ZINACOR 850 (85% zinc/15% a...

Condition: new, maximum load weight: 50,400 kg, overall weight: 65,000 kg, axle configuration: > 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle fleet, including vehicles available immediately and at short notice, on our website. Excerpt from the equipment. Full equipment details available upon request. GOOSENECK: * Gooseneck in SNT design for optimization of loading platform length, approx. 3,700 mm long, with rear chamfer approx. 1,000 mm x 10° * For tractor units: 4 x 2, 6 x 2, and 6 x 4 * Plug-in steel front wall, approx. 400 mm high * ASPÖCK UNIBOX at the front connection rail with 24N, 24S & 15-pin sockets * 3 kW electro-hydraulic unit for controlling hydraulic operations, except hydraulic winches * On the gooseneck: 1 pair of plug-in aluminum side walls, approx. 400 mm high, anodized finish * On the gooseneck: 1 plug-in aluminum rear wall, approx. 400 mm high, anodized finish * Gooseneck covered with approx. 40 mm thick hardwood, king pin area with checker plate * 2" king pin LOADING AREA: * Extendable loading platform, approx. 8,800 mm long, with rear chamfer approx. 500 mm x 10° Hodpfx Aaoyhkrfjajnk * A depression in the platform and chamfer to take up excavator dipper sticks, approx. 3,850 x 750 x 210/290 mm (L x W x H) * TPMS tire pressure monitoring system according to ECE R 141. Data transmission to the truck via standard EBS interface in line with ISO 11992. For correct display, the truck must be able to transmit and display this data. * TPMS tire pressure sensors mounted on all wheels * BPW axles and suspension, 1st axle steered, all other axles hydro-mechanically forced-steered * 1st axle with electromagnetic reverse lock, activated by reverse gear and manually * Technical axle load: 12,000 kg each * Air suspension with lift and lower valve * Axle tools * Mechanical landing legs with 2-speed gearbox and crank, JOST Modul B, static test load = approx. 50,000 kg * 245/70 R 17.5 3PMSF twin tires. Brand at our discretion. Load index 143/141J (146/146F) * Loading area with continuous (between the axles interrupted) 50 mm thick hardwood floor (provides increased coefficient of friction) * Platform locked using welded-on conical locking profiles, every approx. 250 mm; includes pre-tensioning plate * 1 intermediate platform, approx. 300 mm wide, for large-diameter sliding tube * Intermediate platform with recessed loading area and extendable suspension bars for aluminum bridging elements * 1 pair of lashing rings on the front cross-member (LC 10,000 daN) * 8 pairs of recessed lashing rings in the outer frame of the loading area, fold-out to the outside (LC 10,000 daN) * Extendable (galvanized) platform wideners, approx. 230 mm each side (without wooden planks) * Wheel recesses with square climbing strips, approx. 15 x 15 mm in front of the axles, fully open to the gooseneck cross-member, approx. 700 x 410 mm (W x D) * ALU covers for the wheel recesses that can also be used as bridging elements for the extension OR as platform widening planks (if the vehicle is equipped with extendable wideners) * Wheel recesses with square climbing strips, approx. 15 x 15 mm between 1st and 2nd axle, approx. 1,480 x 700 x 410 mm (L x W x D) * 1 pair of mechanical rear supports * Steering from front and rear via cable remote control, with single-track control of the axles HYDRAULIC LOADING RAMPS: * DR-15/60-900-4350-KG-HV-M: One pair of two-piece steel ramps, approx. 4,350 mm long and approx. 900 mm wide

Condition: new, maximum load weight: 37,075 kg, overall weight: 48,000 kg, axle configuration: 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete range of vehicles, including immediately available and short-term delivery vehicles, on our website. Sample of the equipment. Full equipment details available on request. Neck (Gooseneck): * Gooseneck with front corners bevelled approx. 45° and rear bevel approx. 750 mm x 10° * 3 pairs of lashing rings (LC 5,000 daN) * Hardwood flooring approx. 30 mm thick Loading Platform: * Loading area behind the gooseneck hydraulically liftable and lowerable, length approx. 2,800 mm, with rear bevel approx. 1,000 mm x 8° * 6 pairs of external foldable lashing rings (LC 5,000 daN) * 2 pairs of external foldable lashing rings (LC 10,000 daN) * 1 pair of internal foldable lashing rings at the central beam front (LC 10,000 daN) * Cut-outs in the outer frame of the platform for hooking in tensioning straps (LC 2,000 daN) * Grating flooring C40/4 (point load approx. 2.3 t over an area of approx. 20 x 20 cm), treadplate flooring over the axles Two-piece Steel Ramps: * One pair of galvanized two-piece steel ramps, approx. 2,750 + 1,400 x 800 mm, with grating surface C40/4 (point load approx. 2.2 t over an area of approx. 20 x 20 cm) * Ramp with hydraulically folding ramp sections * Hydraulic lift unit, hydraulically adjustable * Maximum load per pair: approx. 40,000 kg Landing Legs: * JOST landing legs (mechanical) with 2-speed gearbox for approx. 24 t lift capacity (approx. 50 t test load) Axles: * BPW axles and suspension, 2 fixed axles, 1 self-steering axle * Technical axle load: 12,000 kg each * Electromagnetic reversing lock automatic via reverse gear and manual activation * Air suspension with lift and lower valve Braking System: * WABCO braking system in compliance with EU regulations with EBS-E (2S2M) Tyres: Tyres 235/75 R 17.5 3PMSF – make at our discretion TPMS: * TPMS tyre pressure monitoring system according to ECE R 141 Paintwork: * HRM metallisation of the complete vehicle chassis with ZINACOR 850 (85% zinc / 15% aluminium) to ensure maximum corrosion protection * Final coating with 2 layers of 2K topcoat, single-coloured in RAL 3002 Carmine Red as per RAL System 841GL * Rims in silver grey Hedpfx Aajyhkrreasnk Accessories included: * 2-inch king pin * Galvanized steel front wall approx. 400 mm high * Grating in the gooseneck bevel C30/3 (point load approx. 2 t over an area of approx. 20 x 20 cm) * Grating in the platform bevel C40/4 (point load approx. 3.4 t over an area of approx. 20 x 20 cm) * Electric-hydraulic unit at the rear under the platform * Plug-in aluminium side and rear boards on the gooseneck, approx. 2,440 x 400 mm (L x H). Rear galvanized insert stanchions removable. (Body length approx. 2,560 mm) * Electric winch with radio remote control, approx. 5,400 kg lifting capacity, including approx. 9.5 mm thick steel cable, approx. 24 m long, with cable guide roller * Bolted approx. 5 t ring for winch cable loop on the neck without deflection pulley * One galvanized toolbox integrated in the sloped gooseneck with opening for a winch * Grating on the gooseneck C30/3 (point load approx. 2 t over an area of approx. 20 x 20 cm) * 7 pairs of stanchion sockets for plug-in stanchions, approx. 100 x 50 mm, in the outer frame of the platform * Lift axle on the front axle, controlled by TEBS E depending on actual axle load and current loading status * 7 pairs of recessed lashing rings along the central beam (LC 5,000 daN): 2 pairs in the lift bed, 5 pairs in the rear section of the platform

Condition: new, overall weight: 55,000 kg, axle configuration: 3 axles, total width: 2,540 mm, Year of construction: 2025, Equipment: ABS, You can find our complete vehicle inventory with immediately and short-term available vehicles on our website. Extract from the equipment. Full specification available on request. LOAD AREA: * Gooseneck, length approx. 4,300 mm, with central beam * Load floor in double-extendable design, length approx. 9,300 mm * A support plate approx. 200 mm wide is permanently welded to the center beam * Pneumatic locking system with conical locking pin and reinforced locking positions, supply lines are protected within the extendable beams and automatically adjust to each load floor length (except for the supply to the first lock) * Technical fifth wheel load: 25,000 kg For tractor units: 4x2, 6x2 and 6x4 * TPMS tire pressure monitoring system in accordance with ECE R 141 * BPW axles and suspension, all axles hydro-mechanically forced-steered, mounted on turntables * Technical axle load: 12,000 kg each * Air suspension with lift and lowering valve * 275/70 R 22.5 3PMSF twin tires. Brand of our choice * ASPÖCK-UNIBOX on the front connection panel with 24N, 24S & 15-pin sockets * 3 kW electro-hydraulic unit for hydraulic operations. Without installation of supply connectors on the tractor unit * 4 pairs of recessed lashing rings in the outer frame of the gooseneck, foldable outwards * At the kingpin 1 pair of lashing rings (LC 10,000 daN), all other lashing rings (LC 5,000 daN) * 4 pairs of stake pockets recessed in the outer frame of the gooseneck, for plug-in stakes approx. 100 x 50 mm * 1 transverse stake pocket rail mounted in the load floor of the gooseneck, for plug-in stakes approx. 100 x 50 mm. 1x rear of the gooseneck * 2" kingpin * Mechanical landing legs with 2-speed gearbox and crank * Approx. 32 mm hardwood floor on gooseneck and load area enclosed in ALU-omega profiles Hnodpfx Aexc Axxsaask * 10 pairs of recessed lashing rings in the outer frame of the load area, foldable outwards: - one pair in front of the last axle and at the rear cross member of the trailer (LC 10,000 daN each), all other lashing rings (LC 5,000 daN) * 8 pairs of stake pockets recessed in the outer frame of the load area, for plug-in stakes approx. 100 x 50 mm * 1 lockable stainless steel toolbox, approx. 1,250 x 500 x 550 mm (L x W x H), mounted under the load floor on the left in direction of travel * Remote steering (front and rear) operable via cable remote control, with single-track tracking of the axles, without installation in the tractor unit * Steel front wall, approx. 1,800 mm high, certified version according to EN12642:2016 XL * Round NATO socket on the front connection panel (Maeler & Kaege VG 96 917) * 1 LED work light each left and right at the landing legs, wired to the tractor unit connector * 3 transverse stake pocket rails mounted in load floor of load area, for plug-in stakes approx. 100 x 50 mm * 1 additional removable platform, approx. 500 mm wide, for large cross-section sliding tube, with hardwood covering * 1 additional lockable stainless steel toolbox, approx. 1,250 x 500 x 550 mm (L x W x H), mounted under the load floor on the right in direction of travel * 1 additional lockable stainless steel toolbox, approx. 1,250 x 500 x 550 mm (L x W x H), mounted under the load floor on the left in direction of travel * WADER container pockets in the load area for transport of: 1x 20' container at weight center, 2x 20' containers, 1x 40' container * 1 LED work light each left and right in front of the axles

Condition: new, maximum load weight: 37,075 kg, overall weight: 48,000 kg, axle configuration: 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete range of vehicles, including those available immediately or at short notice, on our website. Excerpt from the equipment list. Full equipment details available on request. Gooseneck: * Gooseneck with front corners beveled approx. 45° and rear taper approx. 750 mm x 10° * 3 pairs of lashing rings (LC 5,000 daN). Hardwood floor approx. 30 mm thick Loading area: * Loading area after the gooseneck hydraulically liftable/lowerable, length approx. 2,800 mm, with rear taper approx. 1,000 mm x 8° * 6 pairs of folding outward lashing rings (LC 5,000 daN) * 2 pairs of folding outward lashing rings (LC 10,000 daN) * 1 pair of inward folding lashing rings at the front central beam (LC 10,000 daN) * Cutouts in the external frame of the loading area for attaching tension belts (LC 2,000 daN) * Grating surface C40/4 (point load approx. 2.3 t on an area of approx. 20 x 20 cm), over the axles checker plate Two-piece steel ramps: * One pair of galvanized two-piece steel ramps, approx. 2,750 + 1,400 x 800 mm, with C40/4 grating (point load approx. 2.2 t on an area of approx. 20 x 20 cm) * Ramp with hydraulically folding in/out ramp sections. Hydraulic lift system, hydraulically adjustable * Maximum load per pair: approx. 40,000 kg Landing gear: * JOST landing gear (mechanical) with 2-speed gearbox for approx. 24 t lifting capacity (approx. 50 t test load) Axles: * BPW axles and suspension, 2 rigid axles, 1 self-steering axle * Technical axle load: 12,000 kg each * Electromagnetic reverse lock via reverse gear and manual activation Hsdpoyhkqzofx Aaaonk * Air suspension with lift and lower valve Brake system: * WABCO brake system according to EU regulations with EBS-E (2S2M) Tyres: 235/75 R 17.5 3PMSF – Manufacturer of our choice TPMS: * TPMS tire pressure monitoring system in accordance with ECE R 141 Paintwork: * HRM metalizing of the entire vehicle chassis with ZINACOR 850 (85% zinc / 15% aluminum) for optimal corrosion protection * Final paint in 2 coats of 2K topcoat, solid color in RAL 3002 Carmine Red in accordance with RAL system 841GL * Rims in silver grey Including accessories: * 2-inch kingpin * One galvanized steel front wall, approx. 400 mm high * Grating in the gooseneck taper C30/3 (point load approx. 2 t on an area of approx. 20 x 20 cm) * Grating in rear taper of the loading area C40/4 (point load approx. 3.4 t on an area of approx. 20 x 20 cm) * Non-slip sand paint on the checker plates above kingpin and loading area * Electro-hydraulic unit at the rear under the loading area * On the gooseneck: plug-in aluminium side walls and rear wall, approx. 2,440 x 400 mm (L x H). The rear galvanized drop-in stakes are removable. (Body length approx. 2,560 mm) * An electric cable winch with radio remote control, approx. 5,400 kg pulling force, including approx. 9.5 mm thick steel cable, approx. 24 m long, with cable guide pulley * Bolted 5 t ring for cable winch deflection on the neck without deflection pulley * One galvanized toolbox integrated in the beveled gooseneck with opening for a winch * Grating on the gooseneck C30/3 (point load approx. 2 t on an area of approx. 20 x 20 cm) * 7 pairs of stake pockets for plug-in stakes approx. 100 x 50 mm in the outer frame of the loading area * Lift axle on the front axle with control via TEBS E depending on current axle load and loading condition * 7 pairs comple...

Condition: new, maximum load weight: 48,300 kg, overall weight: 71,000 kg, axle configuration: > 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory, including units available for immediate and short-term delivery, on our website. Extract from the equipment features. Full specification available on request. GOOSENECK: * Gooseneck with integrated 1-axle running gear (pendulum axle) in detachable design * Gooseneck hydraulically liftable and lowerable, including hydraulic coupling connected with the hydraulic axle compensation of the first axles * Length: approx. 5,200 mm, with a front taper of approx. 60° * Saddle load according to data sheet: W25-DSR2700-12/22.7 * For tractor units: 6 x 4 or 8 x 4 * Front bulkhead made of steel, detachable, approx. 400 mm high, with chamfered design * 1 pair of mechanical supports at the front of the gooseneck * ASPÖCK-UNIBOX on the front connection panel with 24N, 24S & 15-pin sockets * 1 spare wheel holder inside on the front bulkhead of the gooseneck with lifting arm * 2 pairs of recessed lashing rings on the gooseneck (LC 2,500 daN) * 2 pairs of recessed lashing rings in the outer frame of the front chassis, foldable outwards (LC 10,000 daN) * 1 pair of lashing rings at the transition between chassis and loading platform (LC 10,600 daN) * On the gooseneck, 1 pair of plug-in side aluminium drop sides, approx. 400 mm high, anodized finish * On the gooseneck, 1 plug-in aluminium tailboard, approx. 400 mm high, anodized finish * 3.5-inch king pin * TPMS tire pressure monitoring system compliant with ECE R 141 * Round NATO socket on the front connection panel (Maeler & Kaege VG 96 917) * 1 INOX toolbox with 1 lid, mounted on top of the gooseneck on the right in the direction of travel near the aluminium drop side, approx. 1,350 x 400 x 400 mm (L x W x H) LOADING AREA: * Lowbed with external main beams, designed as a telescopic loading platform in low-profile layout with front extension including a fixed approx. 50 mm hardwood floor * Length x width approx. 8,000 mm x 2,740 mm * Mechanical pin-lug coupling from the lowbed to the chassis to exchange the platform or install extension beams * 1 locking position every approx. 500 mm in the extension section * 4 pairs of recessed lashing rings arranged lengthwise on the loading area, distributed along the outer frame/main beam (LC 10,000 daN) * 1 lashing ring per side on the outside of the rear crossmember (LC 10,000 daN) * Foldable widening sections, approx. 230 mm per side (WITHOUT timber planks) * Detachable widening planks, steel-edged * Preparation for installation of bolt-on container positioning devices for 1x 20' or 1x 40' container on the main beams. Container locks not included * 6 pairs of threaded blocks between the lashing rings under the upper flange on the main beam for mounting screw-type M24 rings (LC 8,000 daN) Hnjdeyhkqnepfx Aaaok * 2 pairs of M24 screw rings (LC 8,000 daN) included REAR RUNNING GEAR: * Rear running gear with closed external frame, checker plate decking and continuous prism-shaped excavator recess, approx. 1,450 x 900 x 505 mm, open at rear * Pendulum axle, all axles hydro-mechanically forced steered * Hose burst valve on the axle compensation cylinders with automatic reset function * Hydraulic cylinders with shut-off cocks and pre-insertion facility for securing in raised position * Final paint on axles in 2 coats of 2-pack paint, solid colour DB 7350 Novagrau * Technical axle load: 12,000 kg each * Hydraulic axle compensation * 245/70 R 17.5 3PMSF. Brand at our discretion * Remote steering from front and rear via cable-control, with axle alig

Condition: new, maximum load weight: 36,400 kg, overall weight: 48,000 kg, axle configuration: 3 axles, total width: 2,540 mm, Equipment: ABS, You will find our complete vehicle inventory, including immediately and soon-to-be available vehicles, on our website. Excerpt from the equipment. Full equipment details available upon request. - Gooseneck in SNT design to optimize load platform length, approx. 3,700 mm long, with a rear taper approx. 1,000 mm x 6° - For tractors: 4 x 2 and 6 x 2 - ASPÖCK-UNIBOX at the front connection panel with 24N, 24S & 15-pin sockets - 3 kW electro-hydraulic power pack for hydraulic operations (excluding hydraulic winches). Without supply line installation on the tractor unit - Outer beams of the gooseneck with mounting holes for boltable lashing rings. First hole approx. 200 mm from the front, subsequent holes approx. every 400 mm. 2 pairs of screw-in lashing rings included (LC 5,000 daN) - One mounting hole at the rear upper part of the gooseneck’s outer beams for a boltable lashing ring - 1 pair of screw-in lashing rings included (LC 10,000 daN) - 3 pairs of recessed lashing rings inside the gooseneck’s outer beams (LC 5,000 daN) - 3 pairs of recessed lashing rings in the center of the gooseneck (LC 5,000 daN) - 1 pair of recessed lashing rings at the rear center of the gooseneck (LC 5,000 daN) - Grating covering on the gooseneck and rear taper with 5 mm steel reinforcement - 2" kingpin - Round NATO socket at the front connection panel (Maeler & Kaege VG 96 917) - Spiral cable for powering the electro-hydraulic unit and/or electric winch (approx. 35 mm², approx. 3.5 m long) between trailer and tractor unit, with plug (NATO-NATO) - 1 pair of detachable aluminum side boards on the gooseneck, approx. 400 mm high, anodized finish CARGO AREA: - Cargo area, approx. 9,600 mm long, with rear taper approx. 900 mm x 6° - Cargo area behind the gooseneck hydraulically liftable and lowerable, approx. 3,000 mm long, load capacity up to approx. 9,000 kg - TPMS (Tire Pressure Monitoring System) according to ECE R 141 - BPW axles and suspension, 1st and 2nd axles fixed, 3rd axle with trailing steering. 3rd axle with electromagnetic reverse lock via reverse gear and manual activation - Technical axle load: 12,000 kg each - Air suspension with lift and lower valve - 235/75 R 17.5 3PMSF twin tires. Brand of our choice, load index 143/141J (144/144F) - Mechanical landing legs with 2-speed gearbox and crank Hnedsyhkquepfx Aaaok - Continuous grating flooring with approx. 5 mm steel plating for additional reinforcement, designed for point loads: on the lift bed and cargo area - Painted sand coating on the gooseneck cover plates as well as transition areas between neck and lift bed, lift bed and cargo area, and cargo area and ramps - 1 spare wheel mounting bracket under the cargo area to the right in front of the axles - Cut-outs in the outer frame of the cargo area and lift bed for attaching tie-down straps (LC 2,000 daN) - 11 pairs of recessed, fold-out lashing rings in the outer frame of the cargo area (LC 10,000 daN): 3 pairs in the lift bed outer frame, 8 pairs in the cargo area outer frame - 11 pairs of recessed lashing rings along the central beam (LC 5,000 daN): 3 pairs in the lift bed, 8 pairs in the rear cargo area - Control valves for the hydraulic ramps located on the right side of the vehicle - 1 pair of foldable mechanical rear supports, single-hand operation HYDRAULIC LOADING RAMPS: - 1 pair of two-part AXS steel ramps, approx. 4,920 mm long, and a

Condition: new, empty load weight: 9,450 kg, maximum load weight: 35,550 kg, overall weight: 45,000 kg, axle configuration: 3 axles, loading space length: 9,500 mm, loading space width: 1,560 mm, total width: 2,550 mm, tire size: 385/65 R 22,5, color: grey, Equipment: ABS, Gooseneck: - Gooseneck designed as a loading deck, fitted with aluminum chequer plate - Front tapered approx. 45° - Hydraulic lifting arm, lift/lower range approx. -280/+250 mm - Two kingpin positions at 2,300 mm and 2,000 mm from DSR - Suitable for tractor units: 4x2, 6x2, or 6x4 Hnsdsygvc Hjpfx Aaaok Loading Bay: - Loading bay, length approx. 9,500 mm, with bottom-mounted angle profiles for pallet mounting (distance from kingpin to center of axle assembly approx. 8,000 mm) Axles, Suspension and Tyres: - BPW stub axles, with drum brakes and independent wheel suspension, hydraulic axle compensation with lift and lower function - Axle lowering lock in case of suspension airbag failure, designed for max. pallet height 150 mm - Tyres: 385/65 R 22.5 - TPMS tyre pressure sensors installed in all wheels including the spare - TPMS tyre pressure monitoring system compliant with ECE R 141 Surface Treatment: - Entire steel structure automatically shot-blasted after welding using a turbine blasting system - Second blasting with corundum to optimise coating adhesion - HRM metallisation of the complete vehicle chassis with ZINACOR 850 (85% zinc/15% aluminium) for maximum corrosion protection - Final coat with two layers of 2K topcoat, single colour in Novagrau (DB 7350) - Paint system tested in salt spray test to ISO 9227-NSS; cavity sealing with special wax Included Accessories: - Removable steel front wall, approx. 400 mm high - Tool box with lid, integrated in the rear section of the gooseneck, approx. 640 x 700 x 215 mm - Removable aluminium rear wall on the gooseneck, approx. 400 mm high, anodised - One pair of folding aluminium sideboards on the gooseneck, approx. 400 mm high, anodised - 2" kingpin - 3 pairs of recessed lashing rings on the gooseneck (LC 6,300 daN) - At the front connection rail, yellow-red air couplings; operation lighting for the gooseneck, suspension, and hydraulic load restraints with on/off switch - Mechanical drop tube supports for approx. 48,000 kg support load - Access ladder mounted front right with 2 detachable handrails - WABCO Roll Stability Support (RSS) - 9 pairs of lashing rings (LC 6,300 daN) mounted on the longitudinal beams - Grating platform, level with the guiding rails for load securing, fitted to the longitudinal beams - Hydraulic preparation, including control unit, for mounting 3 pairs of our hydraulic load restraints - First and last axle manually liftable on left and right - Storage box behind axle assembly, left and right, splash-proof - Tapered rear edge for easier pallet loading - Rear lashing eyes mounted on the tail crossmember for mechanical bracing - 7-pin socket on the tail crossmember - Electro-hydraulic power unit - 4 wheel chocks with holders - 2 axle load gauges mounted on the left side incl. axle load diagram - 3 pairs of hydraulic load restraints with swivel arms, moveably mounted to longitudinal beams - Rear door with cross bracing, hinged left and hydraulically locked right, can be secured horizontally at 90°, 105°, and 270° - Folding underride guard for transporting up to 4 empty standard pallets - 1 spare wheel - Number plate holder including lighting, rear left on the trailer - Round NATO socket on front connection rail (Maeler & Kaege VG 96 917) - Central lubrication system with 1 pump, brand BEKAMAX, standard grease version

Condition: used, empty load weight: 9,600 kg, maximum load weight: 30,400 kg, overall weight: 40,000 kg, axle configuration: > 3 axles, first registration: 12/2011, loading space length: 13,200 mm, loading space width: 2,500 mm, loading space height: 800 mm, suspension: air, tire size: 205/65R17.5, color: green, mileage: 1,001 km, gearing type: other, driver cabin: other, Equipment: ABS, Vehicle location: Bovenden, 4 axles, SAF axles, air suspension, lifting and lowering function, 3rd and 4th axles self-steering, ABS (anti-lock braking system), extendable, lashing eyes, drive-on ramps can be fitted, front support legs, rear support legs, lateral aluminium side guard, storage box. Hedpfx Ajxxkqzeaaonk Body: 4-axle low-bed semi-trailer with attachable drive-on ramps, SAF axles, 3rd and 4th axles self-steering, 13 pairs of lashing rings, 10 pairs of preparations for plug-in stanchions, 13,200 mm loading length fully retracted, 16,800 mm loading length fully extended, 800 mm loading height in the low-bed area, low-bed length approx. 9,500 mm retracted, next technical inspection (TÜV) due, aluminium ramps available at extra cost of €1,500. ACCESSORY DETAILS WITHOUT GUARANTEE, subject to change, prior sale and errors excepted. - .

Condition: used, color: red, Year of construction: 2012, Faymonville STBZ-4VA. Year of manufacture: 2012. 10-ton SAF axles. Unladen weight: 22,500 kg. Payload capacity: 57,500 kg. Gross vehicle weight: 80,000 kg. Kingpin load: 40,000 kg. EBS, ABS, ALB. Trailer hydraulics compatible with NATO electrical system. Hydraulically detachable gooseneck. Extendable by 5 meters. 2 x spare tyres. Galvanised (zinc coated)! Air suspension. Excavator bridge: 5,600 x 950 mm. Wired remote control. Dimensions: Gooseneck: Length: 4,500 mm Width: 2,550 mm Height: 1,750 mm Kingpin height: 1,250 mm Loading platform: Length: 7,550 mm Width: 2,750 mm Height: 530 mm Floor thickness: 350 mm Rear section of trailer: Length: 5,600 mm Width: 2,750 mm Height: 1,000 mm Tyres: 235/75R17.5, 80% remaining tread. Dolly D-2: Year of manufacture: 2012. 10-ton SAF axles. Unladen weight: 4,300 kg. Gross vehicle weight: 38,000 kg. Kingpin load: 18,000 kg. Air suspension. Tyres: 235/75R17.5, 70% remaining tread. German trailer! Hnsdeyfn H Iepfx Aaajk ID No.: 589. The General Terms and Conditions of Heinhuis apply to all advertisements, offers, and quotations by Heinhuis, all agreements entered into by Heinhuis, and the negotiations preceding them. By responding in any form, you accept the applicability of the General Terms and Conditions of Heinhuis and declare that you have taken note of them. Our prices are net export prices. = Further information = Year of manufacture: 2012 Unladen weight: 22,500 kg Payload: 57,500 kg Gross vehicle weight: 80,000 kg Extendable body: Yes Price: On request = Company information = For more information: WhatsApp: