Low loader semitrailer

FAYMONVILLE MAX Trailer MAX510 Tiefbett 2x10 t

Condition: new, maximum load weight: 25,645 kg, overall weight: 38,000 kg, axle configuration: 2 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete stock of immediately and soon-to-be available vehicles on our website. Excerpt from equipment specification. Complete specification available on request. Load area: - Low-bed design with central beam, extendable version, approx. 6,750 mm in length - 5 pairs of fold-out external lashing rings (LC 5,000 daN) - 1 pair of fold-out external lashing rings (LC 10,000 daN) - 1 pair of flat-mounted lashing rings at the rear of the loading platform (LC 10,000 daN) Gooseneck: - Hydraulic lifting/lowering gooseneck, detachable Rear chassis: - Short rear chassis with closed outer frame and checker plate covering - Chassis with excavator trough, closed in the rear half for housing the air tanks - 2 pairs of fold-out external lashing rings (LC 5,000 daN) - 1 pair of fold-out external lashing rings (LC 10,000 daN) - 1 pair of flat-mounted lashing rings at the rear of the chassis (LC 10,000 daN) Axles: - BPW axles, hydro-mechanically forced steering - Air suspension with raise/lower control valve Tyres: - Tyres 245/70 R 17.5, 3PMSF - TPMS: Tyre Pressure Monitoring System according to ECE R 141 Brake system: - Wabco braking system in accordance with EU regulations with EBS-E (2S2M) Paintwork: - High-quality single-tone 2-component (2K) top coat in RAL 3000 Flame Red Including the following additional equipment: - 2 kingpins - Galvanised steel front wall, approx. 400 mm high - Remote steering from front and rear, operated by cable remote control with push buttons, including single tracking control for the axles (no installation in the tractor unit) - Electro-hydraulic unit - Axle load gauge including load diagram - On the gooseneck, removable aluminium side walls and rear wall, approx. 2,440 x 400 mm (L x H). Rear galvanised stake pockets are removable. (Body length approx. 2,560 mm) - Separate air connection with air gun on the gooseneck - 2 work lights with switch on the trailer, mounted on the left and right of the gooseneck platform Dedpfx Ahexf Silj Dekh - 1 INOX toolbox, approx. 1,350 x 400 x 400 mm, on the gooseneck - 6 pairs of stake pockets for insertable posts approx. 100 x 50 mm in the outer frame of the load area, 2 pairs in the chassis outer frame - Galvanised, extendable width extensions approx. 230 mm per side - Hydraulic connections from gooseneck to low bed with multi-coupling (instead of screw couplings). No seal guarantee included. - Central lubrication system with 2 BEKAMAX (Pico) pumps, standard NLGI-2 grease, with removable protection around the pump - 2 pairs of WADER container locks on the loading area, for 1x20' container - 1 removable galvanised intermediate table with 1 pair of WADER container locks - 1 pair of steel ramps for bridging the low bed’s hook mountings - Anti-slip sand-coated layer painted on the load area - HRM Metallisation (High Resistance Metallisation)

Condition: new, empty load weight: 17,250 kg, maximum load weight: 48,700 kg, overall weight: 66,000 kg, axle configuration: 3 axles, loading space length: 7,550 mm, loading space width: 2,480 mm, loading space height: 375 mm, tire size: 245/70 R 17.5, color: grey, operation weight: 17,250 kg, Equipment: ABS, Gooseneck: -Gooseneck in SNT design to optimize the loading area length, length approx. 3,750 mm -Gooseneck can be raised/lowered and removed hydraulically -For tractor units: 6 x 4 and 8 x 4 (or 6 x 4 with optional 1-axle dolly) Low bed: -Low bed with external supports, designed as a telescopic tank bridge in low construction with extension at the front -Length x width approx. 7,550 mm x 2,740 mm -Mechanical locking of the extension Chassis: -Chassis at the rear with closed outer frame -Checker plate covering and continuous prism excavator trough approx. 1,450/900 x 505 mm, open at the rear Axles, suspension and tires: -"PENDEL-AXLE", all axles hydromechanically forced steering -Hose rupture valve on the axle compensation cylinder with automatic RESET function -Hydraulic cylinder with shut-off valves and pins for securing in raised position -Final painting of axles with 2 layers of 2-component paint in a single color in "FAY-Gray-34-0260" -Technical axle load 12,000 kg -Hydraulic axle compensation -245/70 R 17.5 Accessories: -Steel bulkhead, plug-in, approx. 400 mm high -4 wheel chocks -Gooseneck in the rear upper area closed with a removable cover -1 pair of steel ramps with climbing strips and fastening bolts to bridge the hooks of the low bed -The ramps can be placed over or between the hooks -Fastening options for the steel ramps at the rear between the outer supports of the gooseneck -One Locking point approximately every 1,000 mm on the extension -1 lashing ring on the left and right on the front cross member -Connection strip for supply lines to the tractor unit, attached at the height of the outer frame profile -6 pairs of threaded blocks on the outside of the inner supports of the loading area for mounting screwable rings M24 -6 pairs of countersunk lashing rings on the outside of the outer supports of the loading area, foldable inwards and outwards -1 pair of threaded blocks at the front and rear of the outer supports of the loading area for mounting screwable rings M24 -Hanging strip for loose aluminum loading ramps on the vehicle's end cross member -Central lubrication system with 2 pumps, BEKAMAX brand -Steering from the front and rear, operated by cable remote control, with alignment control of the axles -3 kW electro-hydraulic unit for controlling the hydraulic processes, with the exception of hydraulic cable winches -Removable loading floor (galvanized) in 3 elements can be inserted between the outer supports with hardwood flooring -Foldable extensions, by approx. 230 mm per side -Extension planks, loose, framed in steel -4 warning signs approx. 423 x 423 mm -Radio remote control for operating the steering -3.5" king pin -Anti-slip sticker on the left bevel of the gooseneck Dodpfjh Hm Tzjx Ah Dokh -Hydraulic connections from the gooseneck to the low bed with multi-coupling instead of screw couplings -Guide plate from the gooseneck for the fifth wheel plate, approx. 800 mm wide -1 spare wheel with mounting adapter -Parking position on the gooseneck for the warning signs when not in use -2 pairs of stake pockets embedded in the outer frame of the chassis, for plug-in stakes approx. 100 x 50 mm -Dipper handle recess of the rear chassis closed at the back with a plug-in plate -Color of the trailer MB 7350 Novagrau

Condition: new, maximum load weight: 33,750 kg, overall weight: 47,000 kg, axle configuration: 2 axles, total width: 2,550 mm, Equipment: ABS, You can find our complete range of vehicles, including those available for immediate or short-term delivery, on our website. Excerpt from the equipment list. Full specification available upon request. Neck: - Gooseneck in SNT design to optimize load platform length, approx. length 3,750 mm - Gooseneck hydraulically raisable/lowerable and detachable - Technical kingpin load: 23,000 kg For tractor units: 4 x 2, 6 x 2, and 6 x 4 Low bed: - Low bed with external beams, extendable SUPER LOW design, approx. length 6,850 mm - Low bed with fixed hardwood floor (approx. 40 mm thick) and mechanical locking - Supply lines run protected inside the extendable beams and adjust automatically to the respective bed length - 5 pairs of fold-out lashing rings (LC 10,000 daN) - 6 pairs of threaded blocks on the inner beam for fitting bolted RUD rings Rear running gear: - Rear running gear with closed outer frame, checker plate surface, and continuous prism-shaped digger recess, approx. 1,250/700 x 505 mm, open at the rear - 2 pairs of fold-out lashing rings (LC 10,000 daN) - 1 pair of laying lashing rings in the recess LC 16,000 daN - 1 pair of laying lashing rings in the recess LC 10,600 daN - 2 pairs of stake pockets for plug-in stakes approx. 100 x 50 mm in the outer frame PENDLE-AXLE: - PENDLE-AXLE system, all axles forced-steered hydro-mechanically - Hose break valve on axle compensation cylinder with automatic RESET function - Hydraulic cylinders with shut-off valves and locking pins to secure in raised position - Axles finished with 2 layers of 2K paint, single-color painted in FAY-Grey-34-0260 - Technical axle load: 12,000 kg per axle, hydraulic axle compensation - Axle tools - Tyres: 245/70 R 17.5 3PMSF – Brand at our discretion. Load index (146/146F) TPMS: - TPMS tyre pressure monitoring system according to ECE R 141 Brake system: - Wabco braking system compliant with EU regulations, with EBS-E (2S2M), without connecting lines to the tractor unit Electrical system: - Electrical system per EU regulations, lighting 24 Volt ASPÖCK-NORDIK (ASS3) - All LED side marker lights flash with the turn signal - ASPÖCK-UNIBOX at the front connection panel with sockets 24N, 24S & 15-pin. Connection according to ISO: 24N ISO-1185, 24S ISO-3731, 15-pin ISO-12098 Steel structure: - Steel structure made of high-strength fine-grained steels - Steel grades: S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa) Painting: - Complete steel structure automatically shot-blasted after welding with a blast wheel system - Second blasting with corundum for optimal coating adhesion - HRM metallization of the entire vehicle chassis with ZINACOR 850 (85% zinc / 15% aluminum) for best corrosion protection - Final painting with 2 layers of 2K topcoat, single-color in RAL 3002 carmine red per RAL system 841GL Including the following additional equipment: - 2-inch kingpin - One galvanized steel front wall, approx. 400 mm high - Remote steering from front and rear via cable control with push buttons, including axle tracking control (without installation in tractor unit) - Electro-hydraulic power unit - 2 pairs of bolted container locks on the outer beams; includes 2 pairs of container locks for 1 x 20' or 1 x 40' container Dksdpoxbmn Usfx Ah Doh - On the gooseneck: removable aluminum side and rear walls, approx. 2,440 x 400 mm (L x H) - Rear galvanized plug-in stakes are removable

Condition: excellent (used), axle configuration: 2 axles, first registration: 06/2015, loading space length: 6,100 mm, loading space width: 2,540 mm, suspension: air, tire size: 235/75/17.5, color: red, Year of construction: 2015, Equipment: ABS, = Additional Options and Accessories = - Air suspension = Further Information = Axle configuration Tyre size: 235/75/17.5 Axle brand: SAF Brakes: Drum brakes Suspension: Air suspension Rear axle 1: Twin tires; Max. axle load: 10,000 kg; Steered Rear axle 2: Twin tires; Max. axle load: 10,000 kg; Steered Weights Unladen weight: 9,900 kg Payload: 35,100 kg Gross vehicle weight: 45,000 kg Functional Loading platform height: 55 cm Extendable superstructure: Yes Condition Technical condition: very good Visual condition: very good Dsdpfx Ahew Dqvwj Dokh FAYMONVILLE MEGAMAX F-S42-1ACA 2-AXLE LOWBED TRAILER SAF AXLES AIR SUSPENSION 1ST AND 2ND AXLES ARE STEERABLE LOAD CAPACITY 35.1 TONNES WABCO EBS-E LOADING PLATFORM LENGTH 610 CM + EXTENDABLE BY 250 CM PLATFORM WIDTH 254 CM PLATFORM THICKNESS 20 CM LOADING PLATFORM HEIGHT +/- 55 CM EXCAVATOR ARM WELL L=315 CM, W=75 CM, DEPTH=28 CM REAR SIDE-MARKER LIGHTS LOAD PLATFORM ANCHOR POINTS TOOLBOX RETURN ROLLER 4 X WHEEL CHOCKS

Condition: new, maximum load weight: 25,300 kg, overall weight: 38,000 kg, axle configuration: 2 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory, including vehicles available immediately or at short notice, on our website. Excerpt from the equipment details. Full specifications available upon request. Neck (Gooseneck) * Gooseneck in SNT design to optimize loading platform length * Approx. 3,750 mm long, hydraulically liftable/lowerable and detachable * Technical fifth wheel load: 25,000 kg For tractors: 4x2 and 6x2 Kessel Bridge (Tiefbett section) * Low bed designed as extendable Kessel bridge in SUPER LOW design * Approx. 6,850 mm length * With mechanical locking * Service lines routed protected inside the extendable beams, automatically adjusting to match the low bed’s length Rear Chassis * Short version with closed outer frame and checker plate cover * Chassis with excavator trough, closed at the rear half to accommodate air tanks Axles * BPW axles and suspension, all axles hydro-mechanically forced steered * Technical axle load: 12,000 kg per axle * Air suspension with lifting and lowering valve Tires * GOODYEAR KMAX T 3PMSF (M+S) 245/70 R 17.5 twin tires. Load index 143/141J (146/146F) Brake system * Brand: WABCO, EBS-E according to EU regulations, without connection cable to the tractor unit Paintwork * 6-Coat final treatment * All-steel construction shot-blasted after welding * 1 layer of zinc-based primer * 1 layer of adhesion primer. Final coating with 2 coats of 2-component acrylic paint in a single color, followed by cavity sealing with special wax Dodov Sw E Aepfx Ah Dskh Trailer color * RAL 3002 Carmine Red * Rim color: Silver grey * Drop side color: Natural aluminum Accessories included * Removable steel front wall, approx. 400 mm high * 3 kW electro-hydraulic unit for hydraulic operations (except for hydraulic winches). Without supply connection installed on tractor unit * Spare wheel carrier in front of the gooseneck front wall * Side beams of the gooseneck with fixing holes for bolted lashing rings; first hole approx. 200 mm from the front, then at approx. every 400 mm * 2 pairs of screw-in lashing rings included (LC 5,000 daN) * 1 lashing ring each left and right on the rear taper of the gooseneck (LC 6,000 daN) * 2" king pin * Hydraulic cross member for supporting the gooseneck on the tractor unit or a dolly * Air connection with air gun at the gooseneck * 1 pair of steel ramps with climbing strips and securing pins to bridge the mountings of the low bed * 1 lashing ring each left and right on the front cross member (LC 10,000 daN) * Outer side beams of the loading area prepared for removable loading floor * Lashing rings with retaining spring at approx. every 1,200–1,300 mm on the inside carrier’s exterior of the loading area * Lashing rings with retaining spring at approx. every 1,200–1,300 mm on the outer carrier’s exterior of the loading area (LC 10,000 daN) * Cut-outs above the lashing rings in the outer carrier’s upper flange * Mechanical pin-tab coupling from low bed to rear chassis, for swapping the loading floor or installing extension beams, with electro-pneumatic-hydraulic couplings * The outer carriers of the low bed coated with anti-slip sand finish for slip resistance * 2nd ride height for high ride position, max. ± 50 mm from normal ride position, without installation of controls from the tractor unit * 1 pair lashing rings with retaining spring at the transition from the low bed to the excavator trough (LC 10,000 daN) * Front and rear tapers

Condition: used, empty load weight: 10,730 kg, maximum load weight: 38,770 kg, overall weight: 49,500 kg, axle configuration: 3 axles, first registration: 07/2024, loading space length: 9,300 mm, loading space width: 2,540 mm, loading space height: 860 mm, suspension: air, tire size: 235/75 R 17,5 3PMSF, color: grey, Year of construction: 2024, Equipment: ABS, Gooseneck: -Gooseneck with beveled corners at the front 45° and with rear bevel of approx. 750 mm x 10° -3 pairs of lashing rings -Hardwood decking 30 mm thick Loading area in extendable version: -Loading surface in extendable version with rear slope of approx. 1,000 mm x 8° -6 pairs of lashing rings can be folded outwards -3 pairs of lashing rings can be folded outwards -1 pair of lashing rings lying in the front of the cargo bed Cut-outs in the outer frame of the cargo bed for attaching lashing straps -Hardwood flooring approx. 48 mm thick, checker plate flooring over the axles Two-part steel ramps: -A pair of galvanized, two-part steel ramps, approx. 2,750 + 1,400 x 800 mm with approx. 48 mm thick hardwood decking -Ramp with hydraulically folding and unfolding ramp sections, hydraulic lifting gear and hydraulically movable -Maximum load per pair: approx. 40,000 kg Axles and tires: -BPW axles and suspension, 2 axles rigid, 1 axle self-steering -Technical axle load: 12,000 kg -Electro-magnetic reverse lock via reverse gear and can be activated manually -Air suspension with lifting and lowering valve -axle tool -235/75 R 17.5 3PMSF -TPMS tire pressure monitoring system Paint finish: -First-class and long-lasting corrosion protection of the standard shot-blasted welded frame guaranteed by a 2-component zinc dust primer A high-quality 2-component top coat in one color in MB 7350 nova grey Accessories included: -One spare wheel with holder in front of the bulkhead -2" kingpin -One galvanized steel bulkhead approx. 400 mm high -Yellow-red air couplings on the galvanized connection strip at the front -4 wheel chocks with holder on the bulkhead -One bracket for rotating beacon at the rear of the trailer -Mounting in the rear area of the gooseneck for ALU trailer lights -Galvanized folding supports under the bevel of the cargo bed -Cover plates to bridge the space between the ramps and the cargo bed -White reflective tape in accordance with EU regulations on the sides, on the extension and red at the rear -Electric hydraulic unit at the rear, under the cargo bed -On the gooseneck and on the ramps on the left and right a holder for the warning signs including socket -Control valves for the ramps mounted on the right-hand side of the trailer -ALU drop sides and rear wall can be plugged onto the gooseneck, approx. 2,440 x 400 mm -The rear, galvanized stanchions are removable Length of the body approx. 2,560 mm -Four warning signs, extendable by approx. 400 mm, approx. 423 x 423 mm with one position light -3 pairs of WADER container pockets in the loading area for a 20ft, 30ft or 40ft container -6 pairs of stake pockets approx. 100x50 mm in the outer frame of the cargo bed -Galvanized extensions, extendable by approx. 230 mm per side Dkodpfxovcpagj Ah Doh -Square climbing rails 20 x 20 mm every 200 mm on the outer frame of the loading area slope -A layer of sand painted onto the chequer plates, above the kingpin and the cargo bed to prevent slipping -On the warning plates a holder for rotating beacon -European reflector plates (red/yellow) at the rear of the trailer -Speed stickers 80 km/h at the rear and on both sides -Load manometer to determine the axle loads including load diagram -HRM metallization (High Resistance Metallization) of the outer frame -Complete steel construction shot-peened, then the defined visible surfaces coated in Metallization with ZINACOR 850 (zinc 85% - aluminium 15%) hot-finished

Condition: used, color: green, Year of construction: 2019, Broshuis 2 ABD-PL. Year of manufacture: 2019. 12 ton Broshuis Pendel X axles. Empty weight: 16,860 kg. Payload capacity: 30,140 kg. Gross vehicle weight: 47,000 kg. Kingpin load: 23,000 kg. Extendable by 5.5 meters. Hydraulic functions from trailer operate via NATO connection. Hydraulically detachable gooseneck. Galvanized (zinc coated). Aluminium sideboards + toolbox on gooseneck. 2 x spare tires. Hydraulic suspension. Power steering. Excavator recess: 2,700 x 490 mm. Radio remote control. Dimensions: Gooseneck: Length: 3,750 mm Width: 2,480 mm Height: 1,550 mm Kingpin height: 1,200 mm Load floor: Length: 8,000 mm Width: 2,550 mm Height: 420 mm Floor thickness: 220 mm Rear section: Length: 2,700 mm Width: 2,520 mm Height: 1,200 mm Tyres: 285/70R19.5 60% tread remaining. German trailer! ID No: 544. The General Terms and Conditions of Heinhuis apply to all advertisements, offers and quotations issued by Heinhuis, as well as to all agreements entered into by Heinhuis and their preceding negotiations. By responding in any manner, you accept the applicability of the General Terms and Conditions of Heinhuis and acknowledge that you have taken note of these terms. Our prices are net export prices. = Further information = Year of manufacture: 2019 Unladen weight: 16,860 kg Payload: 30,140 kg GVW: 47,000 kg Extendable body: Yes Dkodpfx Ahexyyb Es Dsh Price: On request = Company information = For more information: WhatsApp:

Condition: used, functionality: fully functional, empty load weight: 9,000 kg, maximum load weight: 29,000 kg, overall weight: 38,000 kg, first registration: 08/2020, color: red, Year of construction: 2020, ES-GE 2-axle low-bed, non-telescopic, Tridec steering Total weight: 38,000 kg Aggregate load (2 x 10,000 kg): 20,000 kg Fifth wheel load: 18,000 kg Unladen weight +/- manufacturer's tolerance: approx. 9,000 kg Payload: approx. 29,000 kg Overall length: approx. 13,650 mm Overall width: approx. 2,540 mm Length of loading area: approx. 13,200 mm Width of loading area: approx. 2,540 mm Front overhang: approx. 1,200 mm Front radius: approx. 1,750 mm Swing-through radius SZM: approx. 2,100 mm Saddle height: approx. 1,150 mm B dimension: approx. 12,000 mm Length of high bed: approx. 3,700 mm Loading height high bed: approx. 1,480 mm Length of low bed: approx. 6,500 mm Loading height low bed: approx. 250 mm Ground clearance low bed: approx. 100 mm Loading height above axle unit: approx. 3,000 mm Specification SZM A dimension: approx. 4,500 mm Semi-mounted height: approx. 1,150 mm Swing-through radius: approx. 2,100 mm Chassis: - Chassis made from high-quality fine-grained steels - Drop deck in rigid design - Axle unit cannot be lowered - Without excavator trough King pin -2" kingpin Supports - without front jacks Axles - 2 x 10,000 kg axles (17.5"), techn. 12,000 kg each - Gigant make - Closed drum brake. Asbestos-free brake linings - Automatic slack adjusters. Center centering - Center distance approx. 1,360 mm Suspension - Air suspension with lifting and lowering - 2nd ride height for air suspension (+ approx. 30 mm) Steering - Hydraulic stub axle steering - All axles are steered. Make "Tridec" Tires - 9 tires 245/70 R 17.5 with load index 146/146 F - Continental tires - Steel rims Brake - Dual-circuit air brakes in accordance with EC directive, make "Knorr" - Automatic load-dependent brake force control - Controlled via standard red/yellow air clutches in accordance with ISO 1726 - Electronic brake, "EBS", 7-pin socket in accordance with ISO 7638, mounted at the front, in accordance with EU directives. WITH ABS 4S/2M - With RSS (Roll Stability Support) - Parking brake by means of spring-loaded cylinder - 4 wheel chocks with holder - Without connecting hoses (reversible flex) to the tractor unit - Aluminum air reservoir - TIMG2 (Trailer Information Module) fitted to read out the current axle loads Dsdpfx Aeu U Np Tsh Dekh Underride guard - Integrated in the rear end plate Side frame - Side frame made of UNP steel approx. 200 mm Load securing - 13 lashing points per side with 13,400 kg tensile force, can be folded outwards, mounted in the outer frame - 1 pair of lashing rings with approx. 13,400 kg lashing force in the rear area of the gooseneck, approx. 400 mm from the floor - 1 pair of lashing rings with a tensile force of approx. 13,400 kg at the rear in the low bed on the vertical neck - 7 stake pockets per side on the inside of the outer frame, for stakes approx. 80x50x4 mm, evenly distributed in the outer frame over the entire length of the cargo bed - 6 stake pockets welded to the outside of the side member on each side Floor - Approx. 28 mm thick hardwood floor with omega profiles, laid between the side members - Tear plate (approx. 8/10 mm) over the axle unit Front wall - Designed as a storage box with lid, approx. D 400 x H 450 mm, across the entire width of the loading area, beveled corners Drop sides - 3 plug-in anodized drop sides on the gooseneck, approx. 2,440 x 400 mm - Rear stanchions, galvanized Galvanization - Steel blasting of all iron parts - Galvanizing of the chassis Painting - Priming and single-color painting in RAL 3002 chi

Condition: used, Year of construction: 2010, operating hours: 8,049 h, Equipment: all wheel drive, Serial number: VATZ1111LZB024460 Year of manufacture: 2010 - Operating hours: 8,048 h Djdpfeuz Nc Aox Ah Dskh Road registration Permitted total weight: 6,500 kg Hydraulic quick coupler 3rd and 4th control circuit Bucket - Cutting width: 1,900 mm Pallet fork - Fork length: 1,200 mm Tyres: 405/70 R 20 Modifications, prior sale and errors excepted. The description is intended for general vehicle identification only and does not constitute a warranty in the legal sense. The decisive factor is the description in the sales contract. Our offer generally does not include a new roadworthiness (TÜV) inspection. If a new inspection is required, we will be happy to provide you with an offer from our partner workshops! The vehicle may be fitted with advertising decals and/or lettering. Our general terms and conditions of delivery and payment apply.

Condition: new, maximum load weight: 38,140 kg, overall weight: 48,000 kg, axle configuration: 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory, including vehicles available immediately and at short notice, on our website. Excerpt from equipment. Full equipment details available on request. Gooseneck: - Gooseneck with front corners chamfered approx. 45° and rear bevel approx. 750 mm x 10° - 3 pairs of lashing rings (LC 5,000 daN) - Hardwood flooring, approx. 30 mm thick Loading area: Dkjdpfx Asw Tpq Doh Doh - Telescopic loading area with rear incline approx. 1,000 mm x 8° - Between 1st and 2nd axle: one pair of fixed wheel recesses, approx. 1,610 x 970 x 400 mm (L x W x D) - Incl. 3-piece removable galvanized cover over wheel recesses (width approx. 670 mm – max. point load 5 t / pc.) - 1 pair of flat lashing rings at the front of the loading area (LC 10,000 daN) - 4 pairs of outward folding lashing rings (LC 5,000 daN) - 3 pairs of outward folding lashing rings (LC 10,000 daN) - Cutouts in the outer frame for attaching tie-down straps (LC 2,000 daN) Landing legs: - JOST landing legs (manual) with 2-speed gearbox for 24 t lifting capacity (50 t test load) Tyres: - Tyres 235/75 R17.5 3PMSF, make at our discretion - TPMS tyre pressure monitoring system in accordance with ECE R 141 - Data transfer to the towing vehicle via standardised EBS interface as per ISO 11992 - For correct display, the towing vehicle must be able to receive and display this data Axles: - BPW axles and suspension, 2 axles rigid, 3rd axle self-steering - Technical axle load: 12,000 kg - Electromagnetic reverse lockout activated automatically when reversing and manually - Air suspension with lifting and lowering valve. Axle tools Braking system: - WABCO braking system according to EU regulations with EBS-E (2S2M) without piping to the tractor unit Electrical system: - Electrical system per EU regulations - LED lighting 24 Volt ASPÖCK-NORDIK (ASS3) - All LED side marker lights flash with the indicator - ASPÖCK-UNIBOX at front connection strip with 24N, 24S & 15-pin sockets, according to ISO; 24N ISO-1185, 24S ISO-3731, 15-pin ISO-12098 Steel construction: - Steel structure made of high-strength fine-grained steels - Steel qualities: S355J2+N/S355MC (yield strength 355 MPa), S690QL/S700MC (yield strength 690 MPa) Paintwork: - Complete steel structure automatically shot-blasted after welding in a wheel-blasting system - Second shot-blasting with corundum for optimum coating adhesion - HRM metallization of entire chassis with ZINACOR 850 (85% zinc/15% aluminium) for maximum corrosion protection - Final painting with 2 layers of 2K topcoat, single-colour in RAL 3002 Carmine Red, rear section metallized and painted in RAL 9010 Pure White - Metallic finish not available - Paint structure tested in salt spray test according to ISO 9227-NSS - Internal cavities sealed with special wax Including the following accessories: - On the gooseneck and rear, left and right, one holder for warning signs each, including socket - Spare wheel holder in front of the front wall (without spare wheel) - 2-inch king pin - Galvanized steel front wall, approx. 400 mm high - Yellow-red air couplings on the galvanized front connection bar - Galvanized folding supports under the inclination at the rear of the loading area - A hardwood crash protection strip at the rear wall from gooseneck to the loading area - 1 pair of recessed lashing rings along the central beam at the rear inclination (LC 10,000 daN) - Aluminium drop sides and tailgate on the gooseneck