Used Müller-Mitteltal Edu Trailers for sale (251)

Condition: new, maximum load weight: 6,110 kg, overall weight: 8,800 kg, axle configuration: 1 axle, Year of construction: 2025, * KWH 8.8 ML: * RDÜ Tire pressure monitoring system * EBS braking system * Drum brakes * BPW axle * Parabolic springs * Front landing gear * Rear square tube supports with spring assistance, base plate, and safety locking pins for multiple support heights * Drawbar with 40 mm bolt-type towing eye (height-adjustable mm) * 15-pin power connector * LED lighting * Flashing LED side marker lights * Chassis made of torsion-resistant square tubes and cross members * Enclosed steel fenders with splash guards * Enclosed side underrun protection, usable as advertising space * Plastic toolbox with base insert (installed lying down) approx. 500 x 350 x 400 mm * Swiveling cable drum frame, light width between drum arms 1,700 mm, with tension lock for securing the drum at the bearing arm ends and a central claw locking mechanism for securing the drum frame to the chassis * Motor-hydraulic drum drive with oil motor * Valves and adjustable, rubber-coated drive rollers * Hydraulic speed controller and brake for drum drive * Steel drum shaft with 76 mm diameter, including centering and rotatable ends * 1 pair of stepwise offset centering cones made of polyamide * Hydraulic pump unit with petrol engine including hand and electric starter * Fuel tank and hand starter * 13 HP with gear pump (150 bar) * 315/80 R 22.5 tires * 2,690 kg unladen weight * Vehicle is hot-dip galvanized Njdju I Iqfopfx Adwecp * New vehicle with full manufacturer's warranty * Subject to errors and prior sale * Immediately available ex Egestorf

Condition: new, maximum load weight: 10,660 kg, overall weight: 14,400 kg, axle configuration: 2 axles, loading space length: 5,000 mm, loading space width: 2,420 mm, loading space height: 600 mm, Year of construction: 2026, * KA-TA-R 14.4: * Wabco EBS (electronic braking system) * Emergency release device for spring brake cylinders * Tire pressure monitoring with display option in the truck via EBS signal – without requiring truck-side installation * Drum brakes * 2 x 7-ton Gigant axles * Parabolic springs with tandem equalizer assembly * Drawbar adjustable in height by approx. 300 mm with 40 mm flange towing eye * Jost mechanical landing gear at the front * 2 mechanical folding support legs at the rear * Plastic toolbox approx. 750 x 350 x 300 mm, mounted front right on the chassis * 15-pin electrical connector * LED rear lights, 12/24 V * Bolt-on underrun protection * Plastic quarter mudguards * Lashing hooks integrated into the central locking mounts as well as 2 on the front wall * Chassis made of high-tensile fine-grained steel * Steel pallet, 3-way tipper body with reinforced Strong side walls (continuous upper side walls with internal tube reinforcement – without center stanchions – foldable with wall spring assist) * Bolt-on rear stanchions Nsdpfx Adsx Hm Rijwocp * Combined steel double-wing rear doors – asymmetrically split, swiveling and lockable up to 270°, not foldable – with additional swing frame for automatic tailgate opening during tipping; locking via galvanized rotary bar lock at the rear and central locking; deactivation function for automatic tailgate during rearward tipping with open doors * Lashing rings: 1 x 5 tons lashing point in each corner; 4 x 3 tons lashing rings recessed in the outer frame on each side * 4 mm floor plate made of high-tensile steel * Rear mounting rail for loading ramps * Reinforced body with load securing certificate * 1 pair of aluminum loading ramps, approx. 3,570 x 410 mm (capacity 10 tons/pair), suitable for rubber-tired & tracked vehicles * Lockable storage compartment recessed below the load floor in the chassis at the rear for ramps * Drawbar, underrun guard, rear stake, rear folding supports hot-dip galvanized * Axles, springs, air tanks, and landing gear painted in black * Tires: 358/55 R 19.5 * Side wall coating in RAL 9010 pure white * Side wall painting in RAL color of your choice available for a surcharge * Subject to errors and prior sale * Available immediately from calendar week 10/2026 * Sample images

Condition: new, maximum load weight: 10,660 kg, overall weight: 14,400 kg, axle configuration: 2 axles, loading space length: 5,000 mm, loading space width: 2,420 mm, loading space height: 600 mm, Year of construction: 2026, * KA-TA-R 14.4: * Wabco EBS (electronic braking system) * Emergency release device for spring brake cylinders * Tire pressure monitoring with display possibility in the truck via EBS signal – no vehicle-side installation required * Drum brakes * 2 x 7 t Gigant axles * Parabolic springs with tandem equalizing unit * Height-adjustable drawbar, adjustable by 300 mm with 40 mm flange towing eye * Jost mechanical support leg at the front * Two mechanical folding supports at the rear * Plastic toolbox approx. 750 x 350 x 300 mm mounted on the right front side of the chassis * 15-pin electrical connector * LED tail lights 12/24 V * Bolt-on rear underrun protection * Plastic quarter mudguards * Lashing hooks at the central locking mounts and two units at the front wall * Chassis made of fine-grain steel * Steel pallet body, 3-way tipper with reinforced Strong side boards (continuous upper side walls with internal tube reinforcement – no center stanchions – foldable with board spring assist) * Rear stanchions bolted * Combination steel double wing doors, asymmetrically split at the rear, can swing and be locked at 270° – non-foldable – plus an additional swing frame for automatic rear tailgate opening during tipping, rear lock by galvanized rotary bar lock and central locking, deactivation function for auto tailgate during reverse tipping with an open wing door * In each corner 1 x 5 t lashing point, and in each side 4 x 3 t lashing rings recessed in the outer frame * 4 mm floor plate made of fine-grain steel * Rear mounting rail for loading ramps * Reinforced body with load securing certificate Ncsdpfx Adsx Hm Rcswep * 1 pair of aluminum ramps approx. 3570 x 410 mm (load capacity 10 t/pair), suitable for rubber-tired and tracked vehicles * Rear lockable storage box recessed under the loading area in the chassis for the ramps * Drawbar, underrun protection, rear stanchion, and rear folding supports hot-dip galvanized * Axles, springs, air tank, and support leg painted black * Tires: 358/55 R 19.5 * Side boards painted in RAL 9010 pure white * Painting of side walls in any RAL color available at extra charge * Subject to errors and prior sale * Available immediately from week 10/2026 * Sample images

Condition: used, axle configuration: 3 axles, suspension: parabolic leaf (spring), tire size: 235-75R17.5, Year of construction: 2010, 3-axle flatbed low-loader trailer. Permissible total weight 30,000 kg, payload 22,800 kg. Loading area approx. 8,800 x 2,550 mm, wide load warning package, amber beacon, 32 lashing rings and 4 stake pockets. Two-part hydraulic ramps approx. 2,150+2,000 x 650 mm, adjustable on ramp shaft. Toolboxes. Gigant axles, parabolic suspension, EBS, tires 235-75R17.5. Loading height approx. 940 mm. Cranked drawbar, 40 mm towing eye, 2-line air (Duomatic), 2-line hydraulics, 24 volt. Paintwork: red. = Further Information = Ncjdpfsyqm Ihjx Adwjp Tire size: 235-75R17.5 Suspension: Parabolic suspension Unladen weight: 7,200 kg Payload: 22,800 kg GVW: 30,000 kg Country of manufacture: DE Please contact Jan-Marc Schwickert for further information.

Condition: used, first registration: 06/2011, total width: 25,500 mm,

Condition: like new (used), functionality: fully functional, empty load weight: 4,120 kg, maximum load weight: 14,000 kg, overall weight: 18,000 kg, axle configuration: 2 axles, first registration: 11/2018, next inspection (TÜV): 05/2026, loading space length: 4,995 mm, loading space width: 2,380 mm, loading space height: 900 mm, loading space volume: 12 m³, suspension: air, tire size: 385/65/R22,5, tire condition: 80 %, maximum speed: 90 km/h, color: orange, trailer brake: trailer braked, Year of construction: 2018, Müller Mitteltal Tandem Three-Way Tipper Trailer – Reinforced & Certified Body – Single Ownership For sale is a Müller Mitteltal tandem three-way tipper trailer with a reinforced and certified body. The trailer is in very good overall condition, comes from first ownership, and has been rarely used – as can be seen from the interior paintwork. Technical Data & Features: - Three-way tipping function - Reinforced, certified body - 50 mm towing eye - ABS - EBS 2S/2M - Air suspension - Crank-operated support leg - Aluminum side panels - Spring-assisted side loading (left) - Automatic tailgate release - Folding underrun protection - Wheelbase: 1,000 mm - Gross weight (GVW): 18,000 kg Njdpfx Aoyrttgjdwocp - Payload: 13,820 kg - Tyres: 385/65 R22.5 – approx. 80% tread This tipper trailer impresses with its robust construction, reliable technology, and practical features. Ideally suited for use in construction, agriculture, or transport sectors. Condition: Very good, well maintained, both technically and visually faultless.

Condition: new, maximum load weight: 10,950 kg, overall weight: 14,400 kg, axle configuration: 2 axles, loading space length: 6,270 mm, loading space width: 2,470 mm, Year of construction: 2026, Equipment: ABS, tail-lift, Müller-Mitteltal ETÜ-TA-R 14.4 Tandem | Low Loader | Flatbed | Trailer Available immediately | Reference number for inquiries: 11611 | Delivery to your address possible * We are happy to offer you an individual quote * ---- * Gross weight: 14.4 t, Payload: 10.95 t * LED lighting system * GIGANT axles, EBS, twin tires 235/75R 17.5, parabolic springs * Tire pressure monitoring system (TPMS) * 6.27m x 2.47m flatbed with galvanized 400 mm front wall * Digger bucket support made of hardwood, bolted to the front wall * Platform height unladen: 930 mm / laden: 870 mm * One-piece ramps with hot-dip galvanized anti-slip grating, telescopic down to approx. 20 mm, secured with support bars and inclined bracing * Ramp assist with vertically mounted, adjustable springs for easy single-person operation * 4 UVV drop lashing rings (LC 6300 daN) * Perforated outer frame (45°-bent with perforation for lashings, lashing capacity per point LC 2000 daN at least 480 mm apart. Installation of drop lashing rings LC 3000 daN at approx. 600 mm spacing possible) with close-spaced transverse profiling, high-profile front and rear ends, rear loading ramp, hot-dip galvanized Nsdpfx Adsyndh Hswscp * 10 UVV lashing rings LC 3000 daN recessed in existing grid in the outer frame, additionally * Further lashing options via boreholes (Ø 50 mm, LC 1200 daN) in the front and rear crossmembers * Tool box in front of the front wall * Side marker lights with indicator function * 50 mm thick softwood floor, chassis hot-dip galvanized * Height-adjustable landing gear at the front, foldable supports at the rear * Retrofitting of 2 container twistlocks possible * Drawbar with 40 mm draw eye (hot-dip galvanized), height adjustable, 50 mm eye available on request * 1 removable LED marker lamp at the rear ---- * Leasing, hire purchase, financing, trade-in possible * e.g. from 510 euros over 60 months, no down payment, no residual value * ---- * Our opening hours: * Monday - Thursday: 08:00 - 17:00 * Friday: 08:00 - 15:00 Outside of opening hours we are available by appointment We speak German, English, Polish, and French Leasing, financing, and trade-in possible

Condition: used, empty load weight: 9,300 kg, maximum load weight: 14,700 kg, first registration: 02/2001, next inspection (TÜV): 10/2024, total width: 25,500 mm, suspension: steel, tire size: 235 / 75 R 17.5 / 10mm, front tire size: 235 / 75 R 17.5 / 10mm, operation weight: 24,000 kg,

Condition: used, maximum load weight: 5,900 kg, overall weight: 9,000 kg, axle configuration: 2 axles, first registration: 05/2020, loading space length: 5,370 mm, loading space width: 2,470 mm, loading space height: 400 mm, loading space volume: 5 m³, Equipment: ABS, * ABS * 5-chamber rear lights Nodpfxsyncyhj Adwjcp * Height-adjustable towing device * Gigant axles * Front landing gear ----Superstructure: Low-loader trailer, loading height approx. 870mm, rear sloped, access height approx. 780mm, spring-assisted steel side walls left and right, wooden floor, lashing eyes and lashing rings. Spring-assisted and laterally adjustable loading ramps with hot-dip galvanized grating, slip-resistant design (length approx. 2,600mm), automatic rear support coupled with ramp operation, plastic toolbox in front of the bulkhead. Chassis, front wall, drawbar, rear wall, ramps and stakes hot-dip galvanized. Sale to commercial customers only. FOR EXPORT, ONLY THE NET PRICE IS PAYABLE!!! ALL INFORMATION PROVIDED WITHOUT GUARANTEE, INCLUDING EQUIPMENT AND ACCESSORIES. The basis for all purchase contracts, invoices, proforma invoices, orders, and sales discussions are our General Terms and Conditions (see legal notice).

Condition: new, maximum load weight: 20,500 kg, overall weight: 27,000 kg, axle configuration: 3 axles, loading space length: 7,000 mm, loading space width: 2,470 mm, Year of construction: 2026, * ETÜ-TR 27.0 flatbed: * EBS (Electronic Braking System) * Emergency release device for spring brake cylinders * Drum brakes * 3 x 9 t BPW Eco axles * Air suspension with lifting and lowering system, with RTR function * 1st axle liftable * Rear axle with trailing steering function and electro-pneumatic steering lock via PIN reverse gear (trailing axle lock, operable from the tractor unit for maneuvering purposes – no truck-side installation required – assigned to PIN 10 in the 15-pin connector, for maneuvering only, not for public road use) * SmartBoard control box as infotool with pressure sensors for total axle load display * Tire pressure monitoring system with display option in the truck via EBS signal, no truck-side installation required Ncsdpfxor Dpz As Adwjp * Fixed center drawbar with 50 mm flange towing eye (loaded 900 mm, mm height adjustment at the head plate) * Mechanical landing gear at front, mechanical swing-down supports at rear of the chassis * Mechanically adjustable warning sign package at front and rear * Toolboxes made of galvanized sheet steel, powder-coated black, approx. 650 x 300 x 600 mm, mounted on right side * Hydraulic flow divider * Continuous side walls (without center stanchion) up to the beavertail * Folding rear stanchions * Steel rear wall slid in front of the rear stanchions * 15-pin electrical socket * LED tail lights * Removable LED beacon incl. bracket and installation * 2 x LED reversing lights at the rear of the vehicle (switched via reverse gear) * Flashing LED side marker lights * 60 mm larch/douglas fir wooden floor * 400 mm plug-in steel front wall * Perforated outer frame, approx. 45 degrees angled, with mounts for 3 t folding lashing brackets * Each corner fitted with 1 x 10 t lashing ring; additionally 2 x 10 t and 3 x 6.3 t lashing rings per side * Various holes in the front and rear cross members for 1.2 t lashing options * Hydraulic one-piece loading ramps, approx. 3,000 x 720 mm, mechanically adjustable laterally * 4-section hydraulic valve block for potential retrofitting of hydraulic ramp shift * Chassis, drawbar, front wall, mechanical rear supports, loading ramps, and tailgate hot-dip galvanized * Axles, air tanks, flange towing eye, and mechanical landing gear at front painted in black * Hydraulic flow divider in trailer (for hydraulic pump performance in truck from over 40 l/min up to 120 l/min) * New vehicle with manufacturer's warranty * Subject to errors and prior sale * Available from week 13/2026 * Sample images (pictures of the vehicle may differ due to special equipment)

Condition: new, maximum load weight: 16,400 kg, overall weight: 30,000 kg, axle configuration: 3 axles, Year of construction: 2024, * T3 Profile 30.0: * EBS-E (electronic braking system) * TPMS (tire pressure monitoring system) * Emergency release device for spring-loaded cylinders * Drum brakes * 3 x 11 t BPW Eco axles * Air suspension with lifting and lowering function * SmartBoard as infotool on the trailer, with pressure sensors for indicating total axle load per axle group * Side underrun protection * Mechanically adjustable warning sign sets at front and rear * Front axle closed plastic mudguards; rear axle straight galvanized steel skirts, both with splash guards * Folding lid (hot-dip galvanized) for the toolbox on the turntable platform * Toolbox made of galvanized steel sheet, approx. 650 x 300 x 600 mm (black powder-coated), mounted on right side * 15-pin electrical connector * LED lighting 12 / 24 V * Removable LED beacon at rear * Side marker lights with indicator control * Drawbar with 40 mm towing eye and height adjustment via draw spring and turnbuckle * Tire pressure monitoring system with display option inside truck via EBS signal (without installation on the truck side) * Rubber covering on the folding ramps and loading slope left and right (approx. 860 mm long) Nodpfx Aotplv Njdwscp * Rubber covering on the longitudinal beams from front end to rear end * Hardwood flooring on running surfaces of the low-bed platform * 4 stake pockets per side, each with 2 t lashing capacity * Load securing package consisting of: 5 pairs of UVV lashing rings, swingable and lowerable, loadable in all directions and embedded in the outer frame – 13.4 t capacity in the corners, otherwise 10 t * 6 pairs mechanical fold-out outriggers for 3 m total width (excluding the rear slope) * Plank holder under the loading area, longitudinally mounted * Roller stops raised in front of the front wall, with 1 x 6.4 t lashing eye each side * Hydraulic folding ramps (approx. 4,650 x 720 mm) with hydraulically extendable ramp tip and load-holding valves * Hydraulic lateral ramp adjustment * Rear hydraulic support (single-stage cylinder) * Hydraulic flow divider in trailer (for hydraulic pump capacity in truck from over 40 l/min up to max. 140 l/min) * Splash-proof hydraulic control block * Two-line hydraulic system * Loading area over turntable: approx. 1,960 x 2,520 mm * Rear loading area: approx. 6,500 x 2,520 mm (including 860 mm loading slope) * Loaded platform height approx. 890 mm +/- 20 mm air suspension * Chassis, turntable, roller stops, fold-out extensions & ramps hot-dip galvanized * Axles, turntable, drawbar, air tanks etc. painted in black * Loaded platform height: approx. 890 mm +/- 20 mm * New vehicle with manufacturer's warranty * Subject to errors and prior sale * Available from CW 20/2026

Condition: new, maximum load weight: 13,410 kg, overall weight: 18,000 kg, axle configuration: 2 axles, loading space length: 4,995 mm, loading space width: 2,380 mm, loading space height: 900 mm, loading space volume: 11 m³, Year of construction: 2026, * Wabco EBS-E (electronic braking system with RSS) * Emergency release device for spring brake cylinders * Drum brakes Nodpfx Asxl Nkgjdwecp * Tire pressure monitoring system with display option in the truck dashboard via EBS signal – without installation on the truck side * 2 x 9 t Gigant axles * Air suspension with level control during tipping operations * Drawbar with 50 mm flanged towing eye (adjustable by +77 mm and -33 mm using offset plate) * Jost landing gear at the front * Foldable, galvanized steel underrun protection for paver feeding * Enclosed plastic single mudguards * Standing platform at the front wall * Manual rolling tarpaulin * 15-pin electrical connector * LED tail lights with galvanized protective cover * Chassis made from fine-grain steel * Steel 3-way tipper body (side walls with MM profile – continuous without central stanchion – pivoting via manual central locking; left side foldable with tailgate spring assist) * Rolling tarpaulin similar to RAL 7038 agate grey, with tensioning by side ratchets and tensioning rubbers at front and rear * Front wall platform made of grating with climbing step at the drawbar and a hand grip on the front wall * Rear wall – made from HBW 400 steel – swinging with automatic 2-claw lock * 5 mm steel floor made of HBW 450 steel * 4 recessed and foldable 3 t lashing rings per side, integrated into the steel floor * Reinforced and certified body according to EN 12642 XL, including load securing certificate up to 19 t * Tipping platform and side walls painted in RAL 9010 pure white * Tailboard painted in RAL 9010 pure white * Sidewalls painting in any RAL color available at extra charge * Chassis painted in RAL 9011 graphite black * New vehicle with full manufacturer's warranty * Subject to errors and prior sale * Immediately available from Egestorf

Condition: new, maximum load weight: 20,500 kg, overall weight: 27,000 kg, axle configuration: 3 axles, loading space length: 7,000 mm, loading space width: 2,470 mm, Year of construction: 2026, * ETÜ-TR 27.0 Platform: * EBS (Electronic Braking System) * Emergency release device for spring-loaded cylinders * Drum brakes * 3 x 9 t BPW Eco axles * Air suspension with lift and lower system featuring RTR function * First axle liftable * Last axle as trailing steering axle with electro-pneumatic locking via reverse gear PIN (locking of the trailing axle from the tractor unit for maneuvering purposes – no truck-side installation required – assigned to PIN 10 in the 15-pin connector, for maneuvering purposes only, not for public road use) * SmartBoard control box as infotool with pressure sensors for total axle load display * Tire pressure monitoring with display option in the truck via EBS signal (no truck-side installation required) * Fixed central drawbar with 50 mm flange eye (loaded 900 mm, vertical adjustment at the head plate) * Mechanical landing gear at the front, mechanical swing-down supports at the rear of the chassis * Hydraulic flow divider * Continuous side walls (without central stanchion) up to the drive-on ramp * Folding rear stanchions * Steel rear wall inserted in front of the rear stanchions * Mechanically adjustable warning sign package at front and rear * Toolboxes made of galvanized sheet steel – black powder-coated – approx. 650 x 300 x 600 mm, right side * 15-pin electric connector * LED tail lights * Removable LED beacon, incl. bracket and installation * 2 x LED reverse lights at the rear of the vehicle (switched via reverse gear) Nodpfsr Dpzxsx Adwjcp * Flashing LED side marker lights * 60 mm larch / Douglas fir wooden floor * 400 mm slotted steel front wall * Perforated outer frame approx. 45° angled with devices to mount 3 t folding lashing rings * In each corner 1 x 10 t lashing ring, plus on each side 2 x 10 t and 3 x 6.3 t lashing rings * Various holes in the front and rear cross members for 1.2 t lashing options * Hydraulic one-piece loading ramps approx. 3,000 x 720 mm, mechanically adjustable sideways * 4-section hydraulic control block for possible retrofitting of hydraulic ramp shift * Chassis, drawbar, front wall, mechanical rear supports, loading ramps hot-dip galvanized * Axles, air tanks, flange drawbar eye and front landing gear painted in black * Hydraulic flow divider in the trailer (for hydraulic pump output in the truck from over 40 l/min up to 120 l/min) * New vehicle with manufacturer warranty * Errors and prior sale reserved * Available from CW 13/2026 * Sample images (Pictures may differ from the actual vehicle due to special equipment)

Condition: new, maximum load weight: 16,400 kg, overall weight: 30,000 kg, axle configuration: 3 axles, Year of construction: 2024, * T3 Profile 30.0: * EBS-E (electronic braking system) * TPMS (tire pressure monitoring system) * Emergency release device for spring-actuated cylinders * Drum brakes * 3 x 11 t BPW Eco axles * Air suspension with lift and lowering system * SmartBoard as an information tool on the trailer with pressure sensors to display total axle load per axle group * Side underrun protection * Mechanically adjustable warning sign packages, front and rear * Front axle closed plastic mudguards and rear axle straight galvanized steel splash guards, each with spray protection * Hinged lid (hot-dip galvanized) for the toolbox located on the turntable platform * Toolbox made of approx. 650 x 300 x 600 mm galvanized steel (black powder-coated), mounted on the right side * 15-pin power connector * LED lighting 12 / 24 V * Removable LED beacon at rear * Side marker lights with indicator control * Tow bar with 40 mm drawbar eye and height adjustment via draw spring & turnbuckle * Tire pressure monitoring system with indication in the truck via EBS signal (no truck-side installation required) * Rubber coating on the folding ramps and on the approach slope, left and right (approx. 860 mm long) * Rubber coating on longitudinal beams from front bulkhead to rear crossmember * Hardwood flooring on the running surfaces of the low-loader platform * Four stake pockets per side, each with 2 t lashing option * Load securing package consisting of: 5 pairs of UVV lashing rings, swivel and retractable, loadable in all directions and recessed in the outer frame – 13.4 t in the corners, otherwise 10 t * 6 pairs of mechanical swing-out extensions for 3 m total width (not available on the rear slope) * Board holder mounted longitudinally below the loading area * Roller stop raised in front of bulkhead, with one 6.4 t lashing ring per side * Hydraulic folding ramps (approx. 4,650 x 720 mm) with hydraulically extendable ramp tip and load-holding valves * Hydraulic lateral ramp displacement * Rear support hydraulically operated (single-stage cylinder) * Hydraulic flow divider in the trailer (for hydraulic pump output in truck from over 40 l/min up to max. 140 l/min) * Hydraulic control block splash-proof * Dual-circuit hydraulic system * Loading area above turntable: approx. 1,960 x 2,520 mm * Rear loading area: approx. 6,500 x 2,520 mm (including 860 mm approach slope) * Loaded deck height approx. 890 mm +/- 20 mm (air suspension) Nsdsq Dyvcopfx Adwecp * Chassis, turntable, roller stop, swing-out wideners and loading ramps hot-dip galvanized * Axles, turntable, drawbar, air reservoirs etc. painted in black * Loaded deck height: approx. 890 mm +/- 20 mm * New vehicle with manufacturer's warranty * Subject to errors and prior sale * Available from week 20/2026

Condition: new, maximum load weight: 10,500 kg, overall weight: 14,400 kg, axle configuration: 2 axles, loading space length: 6,270 mm, loading space width: 2,470 mm, loading space height: 400 mm, Year of construction: 2026, * ETÜ - TA -R 14.4 ----Braking system: * EBS braking system * Emergency release device for spring-loaded cylinders * Drum brakes ----Axles: * 2 x 7 t Gigant axles ----Suspension: * Parabolic springs with compensation unit ----Drawbar / Flange Eye: * Height-adjustable drawbar by 300 mm – drawbar extension by 250 mm to 2,250 mm * 40 mm flange towing eye ----Electrics / Lighting: * Tire pressure monitoring with display capability in the truck via EBS signal (no in-truck installation required) * 15-pin power connector * LED rear lights 12/24 V * Removable LED beacon at the rear ----General Accessories: * Support winch at the front * Externally mounted hot-dip galvanized folding supports at the rear * Plastic toolbox approx. 858 x 500 x 500 mm, front right outside on the front wall * Side underrun protection * Plastic quarter mudguards ----Lowbed Area: * Provision in front of the front wall for retrofitting container locks * Bolted front wall made of smooth sheet metal * Side walls made of profiled steel sheet, foldable with side wall spring lifters * Steel rear wall insertable between the ramps – storage bracket inside at the front wall when not in use * Removable bolted rear stanchions * Inclined access ramp at rear, approx. 860 mm ----Floor Covering: * 50 mm softwood floor * 12 mm thick and 270 mm wide rubber strips on the inside of the loading ramps * 12 mm thick and 210 mm wide rubber strips on the access slope and externally on the lowbed platform (from front to rear cross member) ----Load Securing: * Perforated outer frame, approx. 45° angled, with 2 t lashing capacity every 480 mm * Installation option for 3 t folding lashing rings every 600 mm * Each front and rear corner with 1 x 6.3 t lashing ring * Multiple holes in front and rear cross member for 1.2 t lashing options ----Ramps: * One-piece mechanical grating ramps with spring mechanism for one-person operation, approx. 2,750 x 870 mm (retractable to 20 mm) ----Paintwork: * Chassis, drawbar, front wall, tailgate and ramps hot-dip galvanized Ncodpsx Ipapofx Adwjp * Axles, springs, air tanks and flange towing eye painted in black * Side walls painted in RAL 9010 pure white ----Information: * --Reinforced and certified body according to EN 12642 XL including load securing certificate-- * Subject to errors and prior sale * New vehicle with manufacturer's warranty ----Delivery time: Vehicle is immediately available

Condition: new, maximum load weight: 10,500 kg, overall weight: 14,400 kg, axle configuration: 2 axles, loading space length: 6,270 mm, loading space width: 2,470 mm, loading space height: 400 mm, Year of construction: 2026, * ETÜ - TA -R 14.4 ----Brakes: * EBS braking system * Emergency release device for spring-loaded cylinders * Drum brakes ----Axles: * 2 x 7 t Gigant axles ----Suspension: * Parabolic springs with compensating aggregate ----Drawbar / Flange Eye: * Height-adjustable drawbar by 300 mm - drawbar extension by 250 mm to 2,250 mm total length * 40 mm flange towing eye ----Electrics / Lighting: * Tire pressure monitoring with in-cab display option via EBS signal (no installation on truck required) * 15-pin electrical connector * LED tail lights 12 / 24 V * Rear LED beacon (removable) ----General Attachments: * Support crank at the front * Externally mounted, hot-dip galvanized folding supports at rear * Plastic toolbox approx. 858 x 500 x 500 mm, mounted front right on bulkhead * Lateral underrun protection * Plastic quarter mudguards ----Low Bed Deck: * Fixture in front of bulkhead for retrofitting container locks * Bolted smooth-sheet bulkhead * Drop sides made of steel sheet, trapezoidal profile, foldable with drop side spring lifter * Steel tailgate, stowable between ramps - bracket for non-use inside, in front of bulkhead * Bolted rear stanchions * Rear incline approx. 860 mm ----Floor Covering: Njdpfx Aox Ipbaedwjcp * 50 mm softwood floor * 12 mm thick, 270 mm wide rubber strip on inner side of loading ramps * 12 mm thick, 210 mm wide rubber strips in the rear incline and outer area of low bed platform (from bulkhead to rear cross member) ----Load Securing: * Slotted external frame, approx. 45° bent, with 2 t lashing capacity every 480 mm * Option to install 3 t folding lashing rings every 600 mm * In the front and rear corners, 1 x 6.3 t lashing ring each * Various holes in the bulkhead and rear cross member for 1.2 t lashing options ----Ramps: * One-piece mechanical mesh loading ramps with spring mechanism for single-person operation, approx. 2,750 x 870 mm (adjustable down to 20 mm spacing) ----Paintwork: * Chassis, drawbar, bulkhead, tailgate, and loading ramps hot-dip galvanized * Axles, springs, air tanks, and flange towing eye painted in black * Sideboards painted RAL 9010 pure white ----Additional Information: * --Reinforced and certified bodywork to EN 12642 XL, including load securing certificate-- * Errors and prior sale excepted * New vehicle with manufacturer's warranty ----Lead Time: Vehicle available immediately ex Egestorf

Condition: new, maximum load weight: 10,950 kg, overall weight: 14,400 kg, axle configuration: 2 axles, loading space length: 6,270 mm, loading space width: 2,470 mm, Year of construction: 2026, Equipment: ABS, tail-lift, Müller-Mitteltal ETÜ-TA-R 14.4 Tandem | Low-loader | Flatbed | Trailer Ncedjyadz Repfx Adwep Available now. Reference number for inquiries: 27678. Delivery to your address possible free of charge. * We are happy to provide you with an individual quote * ---- * GVW: 14.4 t, Payload: 10.95 t * LED lighting system * GIGANT axles, EBS, twin tires 235/75R 17.5, parabolic springs * Tire pressure monitoring system (TPMS) * 6.27 m x 2.47 m platform with galvanized front wall, 400 mm high * Excavator bucket rest made of hardwood, bolted to front wall * Floor height unloaded 930 mm / loaded 870 mm * One-piece ramps with hot-dip galvanized anti-slip grating, adjustable down to approximately 20 mm, secured with support rods and angle bracing * Ramp assist with vertical, adjustable springs for easy one-person operation * 4 UVV drop lashing rings (LC 6300 daN) * Perforated outer frame (45°-angled with hole pattern for lashing equipment, lashing force per point LC 2000 daN at a minimum distance of 480 mm; option to fit drop lashing rings LC 3000 daN at approximately 600 mm spacing) with closely spaced cross members, high-profile front and rear end sections, rear drive-on ramp, hot-dip galvanized * 10 recessed UVV lashing rings LC 3000 daN in existing outer frame grid, additionally * Further lashing options via bores (Ø 50 mm, LC 1200 daN) in front and end cross members * Toolbox in front of front wall * Side marker lights with indicator control * Softwood flooring, 50 mm thick. Chassis hot-dip galvanized * 2 container locks recessed in front cross member * Height-adjustable landing gear at the front, folding supports at the rear * Drawbar with 40 mm towing eye (hot-dip galvanized), height adjustable; 50 mm towing eye available upon request * 1 removable LED marker light at the rear---- * Leasing, hire purchase, financing, trade-in possible * For example: €515 over 60 months with no down payment, no residual value * ---- * Our business hours * Monday - Thursday: 08:00 - 17:00 * Friday: 08:00 - 15:00 Outside business hours, appointments are available by arrangement We speak German, English, Polish, and French Leasing, financing, trade-in possible

Condition: used, axle configuration: 2 axles, first registration: 02/1992, Year of construction: 1992, Equipment: ABS, Empty weight: 3.140 kg Carrying capacity: 14.860 kg GVW: 18.000 kg Ncedpfx Aext Sd Sjdwsp Selling price: € 1.500, US$ 1.733 Purchase on credit is possible: Yes

Condition: used, axle configuration: 2 axles, first registration: 09/1993, Year of construction: 1993, Equipment: ABS, = Additional options and accessories = - EBS = More information = Empty weight: 4.600 kg Carrying capacity: 13.400 kg GVW: 18.000 kg Njdpfjxt Rw Rsx Adwecp Selling price: € 6.500, US$ 7.511 Tyre tread remainder on axle rear: 50% Make of axle rear: BPW Purchase on credit is possible: Yes

Condition: used, maximum load weight: 9,400 kg, overall weight: 11,900 kg, axle configuration: 2 axles, first registration: 07/2020, loading space length: 6,300 mm, loading space width: 2,480 mm, Ref. No.: ZANDT Very well-maintained tandem flatbed trailer ZANDT Cargo * TAT B 110 * Flatbed * Reinforced wooden floor * Heavy-duty lashing rails * 2-axle tandem * Wide tires * Adjustable drawbar * Perm. gross weight 11,900 kg * Very good condition Trade-in possible Financing from 3.99% Ncsdpsymuz Usfx Adwep Errors and prior sale excepted! The details in this ad are non-binding descriptions and do not constitute guaranteed characteristics. The seller assumes no liability for typographical or data transmission errors. Listed equipment must be verified separately. All information provided in the listings is non-binding! Delivery possible throughout Germany upon request Opening hours: Monday to Thursday from 9:00 a.m. to 5:00 p.m., Friday from 9:00 a.m. to 2:00 p.m., and by appointment!

Condition: used, maximum load weight: 9,400 kg, overall weight: 11,900 kg, axle configuration: 2 axles, first registration: 07/2020, loading space length: 6,300 mm, loading space width: 2,480 mm, Ref. No.: ZANDT Very well-maintained tandem flatbed trailer ZANDT Cargo * TAT B 110 * Flatbed * Reinforced wooden floor * Heavy-duty lashing rails * 2-axle tandem * Wide tires * Adjustable drawbar * Permissible total weight: 11,900 kg * Very good condition Trade-in possible Financing from 3.99% Errors and prior sale excepted! The information in this listing is non-binding descriptions and does not constitute guaranteed features. The seller assumes no liability for typing or data transmission errors. Listed equipment/features must be checked separately. All information in the advertisements is non-binding! Delivery throughout Germany upon request Ncedpfx Ajymuz Ijdwsp Business hours: Monday to Thursday from 9:00 am to 5:00 pm Friday from 9:00 am to 2:00 pm and by appointment!

Condition: new, maximum load weight: 8,750 kg, overall weight: 11,900 kg, axle configuration: 2 axles, loading space length: 5,000 mm, loading space width: 2,420 mm, loading space height: 500 mm, Year of construction: 2026, Equipment: ABS, tail-lift, Müller Mitteltal KA-TA-R 11.9 Tandem Low-Loader Three-Way Tipper Trailer with Ramps Reference number for enquiries: 11612 * NEW VEHICLE, available immediately in RAL 9016 (traffic white), no prior registration * Delivery to your door available for an additional charge! * Gross vehicle weight: 11,900 kg, Payload: 8,750 kg * Galvanized floor 5m x 2.42m x 0.5m, side walls pendulum-mounted, foldable, and removable, prepared for later retrofitting with side board extension kits * Bulkhead/h front wall hot-dip galvanized * Lockable compartment under tipping platform for loading ramp * Includes 3.31m loading ramps, 8t pair * 4 UVV tie-down rings LC 5000daN, located at front and rear * 8 recessed, foldable lashing eyes LC 3000daN in the tipper floor (centered) * Net hooks * Stepless height-adjustable drawbar, hot-dip galvanized, 40mm towing eye * Galvanized frame * Tyres: 235/75R 17.5 (4 units), BPW axles, parabolic springs * Tire pressure monitoring system * EBS (Electronic Braking System) * LED lighting system for 12V and 24V * Side marker lights with indicator activation * Bolted, galvanized rear stanchions Ncodpeyl Ebpjfx Adwep * Excavator bucket holder mounted on front wall ---- Please request a detailed offer; additional equipment available upon request Financing available from only €405 (net) per month, 72 months term, no down payment, no residual value. An offer from our partner 'FM LeasingPartner.' ---- Our office hours: Monday - Thursday: 08:00 - 17:00 Friday: 08:00 - 15:00 Outside of office hours, viewings by appointment. WhatsApp Leasing, financing, and trade-in possible----

Condition: used, overall weight: 11,900 kg, axle configuration: 2 axles, first registration: 02/2021, next inspection (TÜV): 08/2026, loading space length: 4,800 mm, loading space width: 2,430 mm, loading space height: 500 mm, Equipment: ABS, Müller-Mitteltal low-loader tipper - Low-loader and two-way tipper combined in a single vehicle - 40 mm towing eye - Air brake system - Support legs for loading and unloading - Gigant axles - Tyres: 235/75 R 17.5 - Drum brakes - Unladen weight: 3,620 kg - Height-adjustable drawbar - TÜV due: 08.2026 - Safety inspection (SP) due: 02.2026 - Loading area length: 4,800 mm - Loading area width: 2,430 mm Ncjdsyk Rfkopfx Adwjp - Side wall height: 0.5 m Errors and prior sale excepted. Internal vehicle number: 11349.

Condition: new, maximum load weight: 31,900 kg, overall weight: 40,000 kg, axle configuration: > 3 axles, Year of construction: 2026, Equipment: ABS, T 4 Profi 40.0 ----Brakes: * Wabco EBS-E (electronic braking system) * Emergency release device for spring brake cylinders * Drum brakes ----Axles: * 4 x 11 t Gigant axles ----Suspension: * Air suspension with lift/lower function and RtR valve ----Drawbar: * Straight drawbar with 50 mm towing eye and infinitely adjustable height setting ----Electrical / Lighting: * Tire pressure monitoring system with display option in the truck dashboard via EBS signal (no truck-side installation required) * SmartBoard as an infotool with pressure sensors for axle load indication by axle group * 15-pin power connector * LED tail lights * Removable LED beacon at the rear ----General Attachments: Njdpfx Ajylfvmsdwjcp * Warning sign packages front & rear * 2 x toolboxes made of galvanized and powder-coated steel approx. 650 x 300 x 600 mm, mounted on the right side * Front closed plastic single mudguards * Rear straight steel splash guards each with spray suppression * Side underrun protection ----Low-loader Platform: * Rotary-platform extension by 520 mm with 45° corners and 3 integrated storage compartments incl. lockable covers * Flooring over rotary-platform from 50 mm and on low-loader platform from 60 mm softwood * 20 mm rubber flooring instead of timber in the deck area, low-loader length 6,780 mm including access ramp * Rubber flooring on upper access slope left and right, approx. 860 mm long * Each side with 4 stake pockets (no stakes included), 2 t lashing option per pocket ----Chassis: * Chassis made of high-strength fine-grain steel ----Load Securing (Lashing Package): Rotary-platform: * 2 pairs 13.4 t lashing rings in the outer frame of the rotary-platform Low-bed: * Each side with 4 pairs 10 t retractable lashing rings on the outer frame, loadable in all directions * Each side rear with 2 pairs 13.4 t swing-away lashing rings ----Ramps: * Rubber surfacing on foldable loading ramps * Hydraulic folding ramps with hydraulically deployable ramp tips, approx. 4,650 x 720 mm * Hydraulic lateral ramp adjustment & load-holding valves ----Rear Support: * Hydraulic rear support ----Widening: * 8 pairs galvanized folding outriggers for 3 m overall width (not on rear ramp slope) * Extension planks stored in compartment on left side ----Excavator Arm Rest: * Excavator arm rest above rear axle to end of ramp, approx. L=2,100 mm x W=740 mm x H=190 mm * 2 pairs 6.4 t lashing rings on side of excavator arm rest ----Hydraulics: * Hydraulic flow divider in the trailer (for hydraulic pump output in truck over 40 up to max. 120 l/min) ----Loading dimensions: * Rear loading area: approx. 6,780 x 2,520 mm (incl. 860 mm ramp) * Area above turntable: approx. 2,990 x 2,520 mm ----Loading height: * Loaded: approx. 890 mm, +/- 20 mm ----Paintwork: * Reflective contour markings on sides and rear * Chassis, rotary-platform, ramps, and folding outriggers hot-dip galvanized * Axles, drawbar, air tanks, and turntable painted in black tone ----Info: * New vehicle with manufacturer's warranty * Errors and prior sale excepted * Sample images may show special equipment ----Delivery time: * Vehicle available from approx. week 23/2026

Condition: new, maximum load weight: 13,490 kg, overall weight: 18,000 kg, axle configuration: 2 axles, loading space length: 7,000 mm, loading space width: 2,480 mm, Year of construction: 2025, TRA-Kombi 18.0: 3 in 1 = Suitable for roll-off, skip containers and as a low-loader ----Brakes: * EBS-E (electronic braking system) * Emergency release device for spring brake cylinders * Drum brakes ----Axles: * 2 x 10.5-ton axles ----Suspension: * Air suspension with manual lowering function at the rear ----Drawbar: * Pneumatically lowerable drawbar, 2,100 mm long, with 40 mm towing eye and height adjustment ----Electrics / Lighting: * TPMS (tire pressure monitoring system), visualisation in the truck via EBS signal (no installation required on the truck side) * LED rear lights 12 / 24 V * 15-pin power connector ----General Attachments: * Toolbox made of powder-coated sheet steel * Spare wheel holder in basket design, mounted right side * Enclosed side underrun protection * Plastic quarter mudguards with spray protection * Rear plastic bumper guards * Foldable rear A-plate ----Loading Area: * Hot-dip galvanized main frame with raised outer frame to guide roll-off containers * Steel sheet floor with roller recesses in the bogie area * For roll-off container transport, suitable for container lengths of 5,500 - 7,000 mm * Pneumatic 4-point locking clamps and mechanical plug-in stops at the front along the guideway * Transport of up to 2 skip containers with a maximum volume of 10 m³ possible * Includes 8 movable skip guides for lateral centering, front 4 skip guides are plug-in type with swing-out stops * Weld beads as anti-slip coating in the ramp area * Mechanical drop-down supports at the rear ----Load Securing: * 3 pairs of 10 t UVV lashing rings on the sides for attaching securing elements to safely secure the skips, 4 lashing brackets each side in clover-leaf design * 1 pair of 13.4 t UVV lashing rings at the front * 4 x 8 t recessed lashing eyes on each side in the outer frame ----Ramps: Nsdpfsl Tld Isx Adwjcp * Aluminium approach ramps (10.6 t / pair) 2,800 x 470 mm, suitable for rubber-tyred and tracked vehicles (lockable storage compartment at the rear) ----Paintwork: * Reflective contour tape on sides and rear * Hot-dip galvanized frame * Axles and drawbar painted black ----Information: * Load securing certificates according to DIN 30722-1 * Load securing certificates according to DIN EN 12195-1, DIN EN 12640, DIN EN 12642 and VDI 2700 * --Permissible gross weight of 20,000 kg technically possible-- * New vehicle without initial registration, with manufacturer's warranty * Subject to errors and prior sale ----Delivery Time: * Immediately available ex Egstorf