Used Faymonville Semitrailers for sale (204)

Condition: used, overall weight: 80,000 kg, empty load weight: 16,500 kg, maximum load weight: 63,500 kg, operation weight: 16,500 kg, axle configuration: > 3 axles, loading space length: 8,800 mm, loading space width: 2,540 mm, first registration: 02/2024, suspension: air, color: grey, tire size: 235/75 R 17.5, Year of construction: 2024, Equipment: ABS, You will receive a current and complete inspection and functional report for every used trailer. Gooseneck: -Gooseneck in SNT design to optimize the loading area length, length approx. 3,700 mm, with a bevel at the rear of approx. 1,000 mm x 10° -Technical fifth wheel load: 30,000 kg -For tractor units: 4x2, 6x2 and 6x4 Loading area: -Loading area in double-extendable design, length approx. 8,800 mm with a bevel at the rear of approx. 500 mm x 10° -An approx. 300 mm wide support table with long holes at the front and rear for optional bridging elements that can be attached and moved is welded to the middle support -Pneumatic locking with conical locking bolt and reinforced locking positions, the supply lines are protected in the extendable supports and automatically adjust to the respective loading area length Axles and tires: -BPW axles and Suspension, 1st axle with leading steering, all other axles with hydro-mechanical forced steering -1. Axle with electro-magnetic reversing lock, can be activated via reverse gear and manually -Technical axle load: 12,000 kg air suspension with lifting and lowering valve -235/75 R 17.5 3PMSF twin tires -Load index 143/141J Accessories: -Steel bulkhead, pluggable, approx. 400 mm high -Connection strip for supply lines to the tractor unit, installed at the height of the outer frame profile -Spiral cable to supply the electro-hydraulic unit and/or the electric cable winch (35 mm2, 3.5 m long) between the trailer and tractor unit with plug -3 kW electro-hydraulic unit to control the hydraulic processes, with the exception of hydraulic cable winches -Parking position on the gooseneck for the warning signs when not in use -1 spare wheel -1 pair of pluggable aluminum side walls on the gooseneck side, approx. 400 mm high, anodized -On the gooseneck a plug-in aluminum rear wall, approx. 400 mm high, anodized -Hardwood covering on the slope of the loading area -3.5" kingpin (optional 2") -Guide plate from the gooseneck for the fifth wheel plate, approx. 500 mm wide -2 brake shoes with bracket -Mechanical saddle supports with 2-speed gearbox and crank -JOST module B - static test load = 50,000 kg -On the loading area, continuous hardwood covering, approx. 50 mm thick, interrupted between the axles -Locking of the loading area with conical welded locking profiles, on the first 3,000 mm extension of the extension tube with a large cross-section, a locking point every 500 mm -Elongated holes for hanging and movable bridging elements: on the loading area front -Extensions (galvanized) extendable by approx. 230 mm per side Ibodpev Aun Aofx Abljc -1 pair of mechanical rear supports -Central lubrication system with 1 pump -One single-piece INOX storage box, approx. 2,480 x 340 x 390 mm -Radio remote control for operating the steering, in addition to the cable remote control, with 2 indicator lights on the receiver as a lane control -2 axle load gauges mounted on the left side including axle load diagram -1st axle with automatic lifting axle function -4 warning signs, approx. 423 x 423 mm, extendable -Complete HRM metallization (High Resistance Metallization) -Complete steel construction shot blasted, then hot-finished with ZINACOR 850 (zinc 85% - aluminum 15%)

Condition: used, overall weight: 85,000 kg, empty load weight: 17,450 kg, maximum load weight: 68,650 kg, axle configuration: > 3 axles, loading space length: 9,400 mm, loading space width: 2,740 mm, loading space height: 850 mm, first registration: 03/2024, color: grey, tire size: 245/70 R 17.5, Year of construction: 2024, Equipment: ABS, Gooseneck: -Gooseneck in SNT design to optimize the loading area length, length approx. 3,700 mm, rear with bevel approx. 1,000 mm x 10° Cargo bed: -Loading area in extendable design with Super-Grip rubber coating over the axles, length approx. 9,400 mm with bevel at the rear approx. 500 mm x 10° -One recess in the loading area and protruding into the chamfer to accommodate the excavator dipper stick approx. 3950 x 780 x 370/450 mm -Pneumatic locking with conical locking pin and reinforced locking positions Axles and tires: Semi-axles type TWINAXLE II, independent wheel suspension, 1st axle self-steering, all other axles hydro-mechanically forced steered -1st axle with electro-magnetic reverse lock via reverse gear and manual activation -Technical axle load: 12,000 kg -Hydraulic axle compensation -Hydraulic cylinder with shut-off valves -Tires: 245/70 R 17.5 3PMSF dual tires Two-piece steel ramps: -A pair of two-piece steel ramps with a length of approx. 4,650 mm and a width of approx. 900 mm -With Super-Grip rubber coating -Hydr. folding ramp tips -Ramps can be moved individually hydraulically by approx. 235 mm outwards and approx. 215 mm inwards Fully metallized: -Complete HRM metallization (High Resistance Metallization) -Complete steel construction shot-blasted, then hot-finished with ZINACOR 850 (zinc 85% - aluminum 15%) Accessories: -steel front panel, pluggable, approx. 400 mm high Ijdpfx Ajt Dpiyoblsbc -1 INOX tool box, one-piece, approx. 2,480 x 340 x 390 mm -Round NATO socket on the front connection strip (Maeler & Kaege VG 96 917) -3 kW electro-hydraulic unit for controlling the hydraulic processes, with the exception of hydraulic cable winches -1 Spare wheel -On the gooseneck 1 pair of plug-in ALU side panels, approx. 400 mm high, anodized -One plug-in ALU rear panel on the gooseneck, approx. 400 mm high, anodized -Approx. 40 mm thick hardwood covering over the gooseneck, checker plate covering over the kingpin -Guide plate from the gooseneck for the saddle plate, approx. 500 mm wide -4 brake shoes -Mechanical seat posts with 2-speed gearbox and crank -JOST module B - static test load = 50,000 kg -Approx. 50 mm thick hardwood flooring on the loading area, checker plate flooring over the axles -Locking of the cargo bed with conically welded locking profiles every 250 mm, including pretensioning plate -1 Sliding intermediate table, approx. 300 mm wide -Widenings extendable by approx. 230 mm per side -1 Pair of hydraulic rear supports -Central lubrication system -Cable remote control operated via pushbuttons, with track-in control of the axles -Radio remote control Rubber floor "Super Grip" 25 mm and sheet metal floor Square climbing rails 20 x 30 mm WABCO Smart Board System Square climbing rails 20 x 30 mm, approx. every 200 mm on the outer frame of the ramp 4 warning signs, approx. 423 x 423 mm, extendable by approx. 1,000 mm, incl. 2 position lights and brackets for rotating beacon

Condition: new, overall weight: 49,000 kg, empty load weight: 12,800 kg, maximum load weight: 36,200 kg, operation weight: 12,800 kg, axle configuration: 2 axles, loading space length: 6,850 mm, loading space width: 2,550 mm, loading space height: 375 mm, color: grey, tire size: 245/70 R 17.5, Equipment: ABS, Gooseneck: - Gooseneck in SNT design to optimize the loading area length, length approx. 3,750 mm - Gooseneck hydraulically raised/lowered and removable - Technical fifth wheel load: 25,000 kg - For tractor units: 4 x 2, 6 x 2, and 6 x 4 Loading area: - Low bed with external supports, designed as a telescopic tank bridge in a low construction with a front extension - Length 6,850 mm x Width 2,540 mm - One locking point approximately every 1,000 mm on the extension Rear chassis: - Rear chassis with closed outer frame with checker plate cover and continuous prism excavator trough approx. 1,250/700 x 505 mm, open at the rear Axles, suspension, and tires: - "PENDEL-AXLE", all Hydro-mechanically forced-steered axles - Hose rupture valve on the axle balancing cylinder with automatic reset function - Hydraulic cylinder with shut-off valves and pins for securing in the raised position - Final axle painting with two coats of 2-component acrylic paint in a single color "FAY-Gray-34-0260" - Technical axle load: 12,000 kg - Hydraulic axle balancing - Tires: 245/70 R 17.5 - TPMS tire pressure monitoring system in accordance with ECE R 14 - TPMS tire pressure monitoring sensors installed in all wheels, including spare tires Accessories included: - Steel bulkhead, plug-in, approx. 400 mm high - 3 kW electro-hydraulic unit for controlling the hydraulic processes, with the exception of hydraulic cable winches - One spare tire with mounting adapter - Gooseneck outer support with mounting holes for screwable lashing rings -Slidable aluminum side walls on the gooseneck, approx. 400 mm high, anodized -Slidable aluminum rear wall on the gooseneck, approx. 400 mm high, anodized -Checker plate covering above the gooseneck -Gooseneck guide plate for the fifth wheel plate, approx. 500 mm wide -Illuminated control panel on the gooseneck with on/off switch -Hydraulic crossbar for supporting the gooseneck on the tractor unit or a dolly -2" kingpin -Anti-slip sticker on the left slope of the gooseneck -Gooseneck closed at the rear upper area with a removable cover -4 chocks with brackets -Hydraulic connections from the gooseneck to the drop bed with multi-coupling instead of screw couplings -1 pair of steel ramps with climbing rails and fastening bolts for bridging the drop bed's hooks -The Ramps can be installed over or between the hooks. -Attachment option for the steel loading ramps at the rear between the outer supports of the gooseneck. -Prepared for screw-on container holders for 1x20f on the outer support. -Mechanical bolt-and-lug coupling from the low bed to the chassis, for replacing the loading area or installing extension supports. -With electro-pneumatic-hydraulic couplings. -The outer supports of the low bed are provided with a painted layer of sand as a slip protection. Ijdpfjvy Edcjx Ablebc -Removable loading floor (galvanized) in 3 elements, insertable between the outer supports with hardwood flooring. -Foldable extensions, by approximately 230 mm per side. -Hanging rail at the front of the rear chassis to the low bed for loose loading ramps. -2 pairs of stake pockets recessed into the outer frame of the chassis, for plug-in stakes approx. 100 x 50 mm. -Hanging rail for loose Aluminum docking ramps on the vehicle's end crossbar -Central lubrication system with 2 pumps -Wireless and cable remote control -4 warning signs, approximately 423 mm x 423 mm extendable -Extensive lashing positions

Condition: new, overall weight: 76,500 kg, empty load weight: 14,800 kg, maximum load weight: 61,700 kg, axle configuration: > 3 axles, loading space length: 9,300 mm, loading space width: 2,540 mm, loading space height: 900 mm, color: grey, tire size: 235/75/r17,5, Equipment: ABS, Gooseneck: -gooseneck with rear bevel of approx. 750 mm x 10° -3 pairs of lashing rings -Hardwood decking 30 mm thick Loading area: -Loading area in extendable design with rear bevel of approx. 500 mm x 8° -9 pairs of lashing rings can be folded outwards -1 pair of lashing rings lying in the front of the cargo bed Cut-outs in the outer frame of the cargo bed for attaching lashing straps -Hardwood flooring approx. 48 mm thick, checker plate flooring over the axles Seat posts: -JOST fifth-wheel supports (mechanical) with 2-speed gearbox for 24 t lifting load (50 t test load) Axles and tires: -BPW axles and suspension, 1st axle self-steering, 2nd + 3rd axle rigid, 4th + 5th axle self-steering. -Technical axle load: 12,000 kg -1.4th and 5th axle with electro-magnetic reverse lock via reverse gear and manual activation -235/75 R 17.5 3PMSF tires Brake system: -WABCO brake system in accordance with EU regulations with EBS-E (4S3M) Paint finish: -First-class and long-lasting corrosion protection of the standard shot-peened welded frame guaranteed by a 2-component (2K) zinc dust primer A high-quality 2-component (2K) top coat in a single color in MB 7350 nova grey -Rear part metallized and painted in RAL 9010 (pure white) Steel construction: -steel construction made from high-strength fine-grained steels -Steel qualities: -S355J2+N/S355MC (yield strength 355MPa) -S690QL/S700MC (yield strength 690MPa) Accessories: -One spare wheel with holder in front of the bulkhead -2" kingpin -One galvanized steel bulkhead approx. 400 mm high -Yellow-red air couplings on the galvanized connection strip at the front -2 pieces of restraining shoes with holder on the bulkhead -Mounting in the rear area of the gooseneck for ALU docking ramps -Galvanized extensions, extendable by approx. 230 mm on each side -One bracket for a rotating beacon at the rear of the trailer -Galvanized supports under the bevel of the loading area -White reflector tape in accordance with EU regulations on the sides, on the pull-out and red at the rear -On the gooseneck and on the rear plate on the left and right, one holder each for the warning signs including socket -ALU drop sides and rear wall can be plugged onto the gooseneck approx. 2,440 x 400 mm -The rear galvanized stanchions are removable (length of the body approx. 2,560 mm) -3 pairs of WADER container pockets in the loading area for a 20ft (30ft) or a 40ft container -7 pairs of stanchion pockets for 100 x 50 mm stanchions in the outer frame of the cargo bed -Lift axle on the front axle with control by TEBS E depending on the current axle load and the current load status -Sliding suspension rails for ALU docking ramps at the rear of the vehicle -Square climbing rails 20 x 20 mm every 200 mm on the outer frame of the sloping loading area -BEKAMAX (Pico) central lubrication system with NLGI-2 standard grease and removable protection around the pump -Four warning signs approx. 423 x 423 mm, extendable by approx. 400 mm, with a position light -One bracket for rotating beacon on the warning signs -European reflector plates (red/yellow) at the rear of the trailer -Speed stickers 80 km/h at the rear and on both sides -Load manometer to determine the axle loads including load diagram Ibedpfxsma Hf Re Ablec -HRM metallization (High Resistance Metallization) of the outer frame -Complete steel construction shot-blasted, then the defined visible surfaces hot-finished in metallization with ZINACOR 850 (zinc 85% - aluminium 15%)

Condition: new, overall weight: 68,000 kg, empty load weight: 15,900 kg, maximum load weight: 63,500 kg, operation weight: 52,100 kg, axle configuration: > 3 axles, loading space length: 12,700 mm, loading space width: 2,740 mm, loading space height: 860 mm, suspension: air, color: grey, tire size: 235/75/r17,5, Equipment: ABS, Gooseneck: Gooseneck in SNT design to optimize the loading area length, length approx. 3,300 mm, rear with bevel approx. 1,000 mm x 10° Technical fifth-wheel load: 23,000 kg For SZM: 6x2, 6x4 and 8x4 Cargo bed: Loading area in extendable design, length approx. 9,400 mm with bevel at the rear approx. 500 mm x 10° A recess in the loading area and protruding into the chamfer to accommodate the excavator dipper stick approx. 3,850 x 950 x 210/290 mm Pneumatic locking with conical locking bolt and reinforced locking positions, the supply lines are protected in the extendable beams and automatically adjust to the respective loading area length Axles and tires: BPW axles and suspension, 1st axle rigid, all other axles hydro-mechanically forced steered Technical axle load: 12,000 kg Air suspension with lifting and lowering valve Axle tool 235/75 R 17.5 3PMSF dual tires Load index 143/141J (144/144F) Ijdpfx Aemfqi Isblobc Two-piece steel ramps: A pair of two-piece steel ramps with a length of approx. 4,350 mm and a width of approx. 900 mm Hardwood decking Hydraulically hinged ramp tips Ramps can be moved individually hydraulically by approx. 235 mm outwards and approx. 215 mm inwards Brake system: WABCO EBS-E brake system in accordance with EU regulations Sockets and lighting: 24-volt lighting system Full metallization: Complete HRM metallization with ZINACOR 850 to ensure the best corrosion protection Surface treatment: Complete steel structure automatically blasted after welding with wheel blast cleaning Second blasting with corundum for optimum adhesion of the coating system Final coating with 2 layers of 2-component paint in a single color in nova grey, followed by sealing of the cavities with special wax Rims in silver gray Steel construction: Steel construction made from high-strength fine-grain steels Steel grades: S355J2+N/S355MC S690QL/S700MC Accessories: Steel end wall, pluggable, approx. 400 mm high Connection strip for supply lines to the SZM Spiral cable for supplying the electro-hydraulic unit and/or the electric cable winch between the trailer and SZM with plug Electro-hydraulic unit for controlling the hydraulic processes, with the exception of hydraulic cable winches Outer beam of the gooseneck with fastening holes for screwable lashing rings The first hole approx. 200 mm from the front, then approx. every 400 mm One fastening hole in the rear upper area of the gooseneck outer beam for a screwable lashing ring Approx. 40 mm thick hardwood covering over the gooseneck, checker plate covering over the kingpin Guide plate from the gooseneck for the fifth wheel plate, approx. 500 mm wide Continuous, approx. 50 mm thick hardwood planking on the loading area, interrupted between the axles Locking of the cargo bed with conically welded locking profiles every 250 mm, including pretensioning plate Slotted holes for attachable and movable bridging elements: on the fixed part behind the gooseneck on the front of the cargo bed 1 movable intermediate table, for the large cross-section extension tube Control valves for the hydraulic ramps on the right-hand side of the vehicle Central lubrication system with 1 pump, with standard grease according to NLGI-2 Radio remote control for operating the steering, in addition to the cable remote control, with 2 indicator lights on the receiver as single-track control

Condition: new, overall weight: 78,000 kg, empty load weight: 14,650 kg, maximum load weight: 63,350 kg, axle configuration: > 3 axles, loading space length: 8,800 mm, loading space width: 2,540 mm, loading space height: 850 mm, color: green, tire size: 245/70 R 17.5, Equipment: ABS, Gooseneck: -Gooseneck in SNT design to optimize the loading area length, length approx. 3,700 mm -Rear gooseneck with bevel approx. 1,000 mm x 10° Cargo bed: -Telescopic loading area, length approx. 8,800 mm, with rear chamfer approx. 500 mm x 10° -Depression in the chamfer and protruding into the loading area to accommodate the excavator dipper arm -Pneumatic locking with conical bolts and reinforced locking positions Ramps: -1 Pair of two-part steel ramps with a length of approx. 4,350 mm and a width of approx. 900 mm -Hydraulically folding ramp tips. -Ramps can be moved individually hydraulically by approx. 235 mm outwards and approx. 215 mm inwards Axles, suspension and tires: Ibjdpsrvw U Sefx Ablec -SAF ∗∗TWINAXLE II∗∗ with independent wheel suspension, 1st axle with self-tracking steering, all other axles with hydro-mechanical forced steering -1st axle with electro-magnetic reverse lock via reverse gear and can be activated manually -Hydraulic axle compensation, hydraulic cylinders with shut-off valves -Twin tires 245/70 R 17.5 3PMSF Surface treatment: -Complete steel construction automatically blasted after welding with blast wheel system -second blasting with corundum for optimum adhesion of the coating system -HRM metallization of the entire vehicle chassis with ZINACOR 850 (85% zinc/15% aluminium) to ensure the best corrosion protection -Finishing coat with 2 layers of 2K top coat, single color in nova grey -Paint structure tested in the salt spray test according to ISO 9227-NSS -Sealing of wooden areas with special wax Accessories included: -steel front wall, plug-in, approx. 400 mm high -3 kW electro-hydraulic unit for controlling the hydraulic processes, with the exception of hydraulic cable winches -On the gooseneck 1 pair of plug-in ALU side panels, approx. 400 mm high, anodized -On the gooseneck, one plug-in ALU rear panel, approx. 400 mm high, anodized -Over the gooseneck approx. 40 mm thick hardwood covering, checker plate covering over the kingpin -Guide plate from the gooseneck for the saddle plate, approx. 500 mm wide -Continuous 8/10 checker plate covering on the loading area -Locking of the cargo bed with conically welded locking profiles every 250 mm -Widenings (galvanized) extendable by approx. 230 mm per side -1 pair of fixed wheel recesses open up to the extension in the cargo bed in front of the 1st axle -Wheel recesses with sheet metal covering and square climbing strips 15 x 15 mm, approx. every 200 mm -1 pair of fixed wheel recesses in the cargo bed between the 1st and 2nd axle -Wheel recesses with square climbing strips 15 x 15 mm and widenings in the lower area -ALU covers for the wheel recesses between the 1st and 2nd axles, which can also be used as widening planks -Aluminum elements designed to lock onto the extension tubes of the extensions -Control valves for the hydraulic ramps on the right-hand side of the vehicle -1 pair of mechanical rear supports -Central lubrication system with 1 pump, BEKAMAX brand -Steering can be operated from the front and rear by remote control cable via pushbuttons, with toe-in control of the axles -Hardwood covering on the bevel of the loading area -Radio remote control for post-steering, in addition to the cable remote control, with 2 LED indicator lights on the receiver as toe-in control. -WABCO Smart Board System. -4 warning signs, approx. 423 x 423 mm, extendable by approx. 1,000 mm, incl. 2 position lights and brackets for rotating beacon

Condition: new, overall weight: 48,000 kg, empty load weight: 10,900 kg, maximum load weight: 37,100 kg, operation weight: 10,900 kg, axle configuration: 3 axles, loading space length: 9,600 mm, loading space width: 2,540 mm, loading space height: 890 mm, suspension: air-lift, color: grey, tire size: 235/75 R 17.5, Equipment: ABS, Gooseneck: -Gooseneck in SNT design to optimize the loading area length, length approx. 3,700 mm, with a bevel at the rear of approx. 1,000 mm x 6° Ibodsuadk Nopfx Ablec -Technical fifth wheel load: 18,000 kg -For tractor units: 4 x 2 and 6 x 2 Loading area: -Loading area, length approx. 9,600 mm with a bevel at the rear of approx. 900 mm x 6° -Loading area can be raised and lowered hydraulically after the gooseneck, length approx. 3,000 mm, load capacity up to approx. 9,000 kg -Grating and sheet metal floor approx. 5 mm as additional reinforcement on the bevel of the loading area Ramps: -A pair of two-part AXS steel ramps with a length of approx. 4,675 mm and a width of approx. 900 mm -Grating floor -Hydraulically hinged ramp tips -Ramps can be moved hydraulically by approx. 235 mm outwards and approx. 365 mm inwards -Painted sand coating on the outer frame of the ramp and on the ramp tip -Flashlights on the outside of the ramp tips with switch next to the ramp controls -Ramp secured in driving position using a quick release Axles, suspension and tires: -BPW axles and suspension, 1st and 2nd axle rigid, 3rd axle with self-steering -1st Axle with traction aid -Operation via the brake pedal in the tractor unit -Technical axle load: 12,000 kg -Air suspension with lifting and lowering valve -235/75 R 17.5 -TPMS tire pressure monitoring system in accordance with ECE R 141 -TPMS tire pressure monitoring sensors mounted in all wheels including spare wheels Braking system: -WABCO EBS-E brand braking system in accordance with EU regulations Paintwork: -Semi-trailer MB 7350 Nova gray Accessories included: -Bulkhead made of steel, plug-in, approx. 400 mm high -3 kW electro-hydraulic unit for controlling the hydraulic processes, with the exception of hydraulic cable winches -Guide plate from the gooseneck for the fifth wheel plate, approx. 500 mm wide -JOST module B - static test load = 50,000 kg -Continuous grating with 5 mm sheet metal underlay as additional reinforcement -Painted sand coating -Cutouts in the outer frame of the loading area and the lifting bed for hanging control valves for the hydraulic ramps on the right of the vehicle -2" kingpin -Central lubrication system with 1 pump, brand BEKAMAX -On the gooseneck 1 pair of plug-in aluminum side walls, approx. 400 mm high, anodized -Electric cable winch, approx. 5,400 kg pulling force, with radio remote control -Wire cable approx. 24 m long, cable ø approx. 9.5 mm, including cable pressure roller -WABCO Smart Board System -4 extendable warning signs, approx. 423 x 423 mm, extendable by approx. 400 mm

Condition: new, overall weight: 47,000 kg, empty load weight: 12,900 kg, maximum load weight: 34,100 kg, operation weight: 12,900 kg, axle configuration: 2 axles, loading space length: 6,850 mm, loading space width: 2,540 mm, loading space height: 350 mm, suspension: other, color: grey, tire size: 245/70 R 17,5, Equipment: ABS, Gooseneck: -Gooseneck in SNT design to optimize the loading area length, length approx. 3,750 mm -Gooseneck can be raised/lowered hydraulically and removed -Technical fifth wheel load: 23,000 kg -For tractor units: 4 x 2, 6 x 2 and 6 x 4 Loading area: -Low bed with external supports in extendable "SUPER LOW" design, length approx. 6,850 mm -Low bed with solid hardwood floor approx. 40 mm thick and mechanical locking Rear chassis: -Rear chassis with closed external frame, checker plate covering and continuous prism excavator trough approx. 1,250/700 x 505 mm, open at the rear -2 pairs of lashing rings that can be folded outwards -1 pair of lashing rings lying in the trough -2 pairs of stake pockets for plug-in stakes 100 x 50 mm in the outer frame Pendulum axle and tires: -"PENDEL-AXLE", all axles hydromechanically forced steered -Hose rupture valve on the axle compensation cylinder with automatic RESET function -Hydraulic cylinder with shut-off valves and pins for securing in raised position -Final painting of axles with 2 layers of 2-component paint, painted in a single color in "FAY-Gray-34-0260" -Technical axle load: 12,000 kg -Hydraulic axle compensation -Tires 245/70 R 17.5 -TPMS tire pressure monitoring system in accordance with ECE R 141 Accessories: -Preparation for screw-on container positioning for 1x 20ft or 1x40ft container on the outer supports Iedpjhlz R Ssfx Ablebc -2" kingpins -A galvanized steel front wall approx. 400 mm high -One spare wheel -Yellow-red air couplings on the galvanized connection strip at the front -4 wheel chocks -Steering from the front and rear can be operated using a cable remote control via push buttons, with alignment control of the axles -Hydraulic connections from the gooseneck to the low bed with multi-coupling instead of screw couplings -Electro-hydraulic unit -White reflector tape in accordance with EU regulations on the side, on the extension and at the rear -European reflector signs (red-yellow) on the rear of the trailer -One holder for the warning signs including a socket on the gooseneck and on the rear panel on the left and right -6 pairs of threaded blocks between the lashing rings under the top strap on the outer support for mounting screwable RUD rings VLBG-4 -ALU side walls and rear wall can be plugged into the gooseneck approx. 2,440 x 400 mm -The rear galvanized plug-in stanchions are removable (Length of the body approx. 2,560 mm) -Gooseneck in the rear upper area closed with a removable cover -5 pairs of stake pockets for 100 x 50 mm stakes in the outer frame of the loading area -Foldable extensions, approx. 230 mm per side -2 pairs of screwable RUD rings VLBG-4 M24 (LC 8,000 daN) -1 pair of steel ramps to bridge the hooks of the low bed -A painted layer of sand on the loading area as anti-slip protection -Speed sticker 80 km/h at the rear and on both sides -Dipper handle recess of the rear chassis closed at the rear with a plug-in plate -Four warning signs extendable by approx. 400 mm, approx. 423 x 423 mm -Radio remote control for the steering in addition to the cable remote control, with indicator lights on the receiver as Alignment control -Central lubrication system with 2 BEKAMAX (Pico) pumps with NLGI-2 normal grease -Load pressure gauge for determining axle loads -HRM metallization (High Resistance Metallization) of the outer frame -Complete steel construction shot blasted, then the defined visible surfaces are hot-finished in metallization with ZINACOR 850 (zinc 85% - aluminum 15%)

Condition: new, overall weight: 42,000 kg, axle configuration: > 3 axles, loading space length: 8,600 mm, loading space width: 2,540 mm, loading space height: 860 mm, suspension: air, tire size: 235/75 r 17.5 3pmsf, color: grey, Equipment: ABS, Loading area: Cranked loading surface with rear chamfer of approx. 500 mm x 8° Recess in the chamfer and protruding into the loading area to accommodate the excavator dipper stick (approx. 2365 x 750 x 235/290 mm (L x W x H)). 4 pairs of lashing rings can be folded outwards (LC 5,000 daN) 2 pairs of lashing rings can be folded outwards (LC 10,000 daN) 2 pairs of lashing rings lying in the front of the cargo bed (LC 5,000 daN) 1 pair of lashing rings lying in the front of the cargo bed (LC 10,000 daN) Cut-outs in the outer frame of the cargo bed for attaching lashing straps (LC 2,000 daN) Hardwood flooring approx. 48 mm thick, above the axles Checker plate covering Brake system: Brake system in accordance with EU regulations with EBS-E (2S2M) with EBS coiled cable to the tractor unit Steel construction: Steel construction made of high-strength fine-grained steels Steel grades: S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa) Coating: First-class and durable corrosion protection of the standard shot-peened welded frame guaranteed by a 2-component (2K) zinc dust primer A high-quality 2-component (2K) top coat in a single color in nova grey Rear section metallized and painted in RAL 9010 (pure white) No metallic paint finish possible Electrical system: Electrical system in accordance with EU regulations, 24 volt lighting ASPÖCK-NORDIK (ASS3) ASPÖCK-UNIBOX with 24N, 24S & 15-pin sockets Connection according to ISO 24N ISO-1185 24S ISO-3731 15 pole ISO-12098 Axles and tires: BPW axles, air-sprung, with drum brake, with lifting/lowering function Axle tool Tires 235/75 R 17.5 3PMSF One-piece steel ramps: A pair of galvanized one-piece steel ramps approx. 3,000 x 800 mm with approx. 48 mm thick hardwood decking Ramp with hydraulic lifting gear and hydraulically movable Maximum load per pair: 40,000 kg Accessories included: Bogie with a +/- 1750 mm long towing fork, with a towing eye (50 mm diameter) Coupling height 830-1,010 mm loaded Spiral cable 15/ 2x7 poles Yellow-red air couplings One mud flap at the rear of the trailer Manual and description on USB stick A bracket for a rotating beacon at the rear of the trailer European reflector plates (red/yellow) at the rear of the trailer White reflective tape in accordance with EU regulations on the side of the trailer and red at the rear Operating valves for the ramps fitted on the right-hand side of the trailer Galvanized supports under the sloping loading area Electro-hydraulic unit at the rear under the cargo bed Cover plates to bridge the free space between ramps and cargo bed 4 restraining shoes with bracket 6 pairs of stanchion pockets for 100 x 50 mm stanchions in the outer frame of the cargo bed Four warning signs approx. 423 x 423 mm, extendable by approx. 400 mm, with an LED position light A bracket for rotating beacon on the warning signs A layer of sand painted onto the central support to prevent slipping Speed sticker 80 km/h at the rear and on both sides Mounting of the individual ramps on the trailer HRM metallization (High Resistance Metallization) of the outer frame Complete steel construction shot-blasted, then the defined visible surfaces hot-finished in metallization with ZINACOR 850 (zinc 85% - aluminium 15%) Galvanized extensions, extendable by approx. 230 mm on each side 2 load manometers to determine the axle loads including load diagram Ibodpfx Ajiziatoblec

Condition: new, overall weight: 49,500 kg, empty load weight: 12,300 kg, maximum load weight: 37,200 kg, axle configuration: 3 axles, loading space length: 9,300 mm, loading space width: 2,480 mm, loading space height: 860 mm, suspension: air-lift, color: grey, tire size: 235/75 R17.5, Equipment: ABS, Gooseneck: -Gooseneck with rear bevel of approx. 750 mm x 10° -Hardwood covering 30 mm thick Two-piece steel ramps: -A pair of galvanized two-part steel ramps approx. 3,185x1,420x1,250 mm with grating decking -Ramp with hydraulically folding and unfolding ramp sections, hydraulic lifting gear Gooseneck: -Gooseneck with rear bevel of approx. 750 mm x 10° -3 pairs of lashing rings -Hardwood decking 30 mm thick Two-part steel ramps: -One pair of galvanized two-part steel ramps approx. 3,185x1,420x1,250 mm with grating covering -Ramp with hydraulically folding and unfolding ramp sections, hydraulic lifting gear -Maximum load per pair: 30,000 kg Loading area: -Loading surface with rear slope of approx. 1,000 mm x 8° -Hardwood flooring approx. 48 mm thick, checker plate flooring over the axles Axles and tires: -BPW axles and suspension, two axles rigid, one axle self-steering -Air suspension with lifting and lowering valve The self-steering axles with electro-magnetic reverse lock can be activated via reverse gear or manually -235/75 R17.5 3PMSF tires Ibsdpfxetvfkfj Ablec Accessories included: -1 Spare wheel with holder -TPMS tire pressure monitoring system according to ECE R 141 -2" kingpin -Galvanized steel bulkhead -Yellow-red air couplings on the galvanized front connecting strip -4 restraining shoes with holder on the bulkhead -Mounting in the rear area of the gooseneck for ALU docking ramps -3 height aluminum boards -Galvanized folding supports under the bevel of the cargo bed Height-adjustable tarpaulin superstructure (3,960 mm) -Galvanized bulkhead with a tensioning mechanism for the sliding curtain -Height-adjustable by approx. 400 mm -"EDSCHA" brand roof can be moved forwards on ALU roof rail profiles bolted to the front and rear wall -3 pairs of sliding stanchions in the loading area -The body can be hydraulically widened at the rear to the left and right by approx. 750 mm -Sliding roof with pivoting portal support -Sliding tarpaulin with 700 mm reserve in length, with tension belts at approx. 600 mm intervals -Height top edge of body approx. 3,960 mm -Driving with the sliding tarpaulin open is not permitted and will damage the tarpaulin -Cover plates to bridge the free space between ramps and loading area -Electric hydraulic unit at the rear, under the cargo bed -On the gooseneck and on the ramps on the left and right, one bracket each for the warning signs including socket -Control valves for the ramps mounted on the right-hand side of the trailer -6 pairs of stanchion pockets for 100 x 50 mm stanchions in the outer frame of the cargo bed -Lift axle on the front axle -Grating in the bevel of the loading area C40/4 (point load 3.4 tons on an area of 20 x 20 cm) -One INOX toolbox 565 x 290 x 810 mm in the direction of travel on the right between the axles -A layer of sand painted onto the chequer plates on the gooseneck and on the loading area to prevent slipping -BEKAMAX (Pico) central lubrication system with NLGI-2 standard grease and removable protection around the pump -Four warning panels approx. 423 x 423 mm, extendable by approx. 400 mm, with a position light -Load manometer for determining the axle loads including load diagram -HRM metallization (High Resistance Metallization) of the outer frame -Complete steel construction shot-blasted, then the defined visible surfaces hot-finished in metallization with ZINACOR 850 (zinc 85% - aluminium 15%)

Condition: new, overall weight: 80,000 kg, empty load weight: 15,450 kg, maximum load weight: 65,550 kg, axle configuration: > 3 axles, loading space length: 21,900 mm, loading space width: 2,540 mm, loading space height: 925 mm, suspension: air-lift, color: grey, tire size: 235/75 R 17.5, Equipment: ABS, Gooseneck: Gooseneck in SNT design to optimize the loading area length, length approx. 3,700 mm, rear with bevel approx. 1,000 mm x 10° Technical fifth wheel load: 30,000 kg. For tractor units: 4x2, 6x2 and 6x4 Loading area: Loading area in double-extendable design, length approx. 8,800 mm with bevel at the rear approx. 500 mm x 10°. A support table approx. 300 mm wide with long holes at the front and rear for optional bridging elements that can be hung and moved is welded to the middle support. Pneumatic locking with conical locking bolt and reinforced locking positions, the supply lines are protected in the extendable supports and automatically adjust to the respective loading area length. Axles and tires: BPW axles and suspension, 1st axle with pre-steering, all other axles with hydro-mechanical forced steering. 1st axle with electro-magnetic reversing lock that can be activated via reverse gear and manually. Technical axle load: 12,000 kg Air suspension with lifting and lowering valve Manufacture of our choice Sockets and lighting: Iodperigw Rsfx Ablsbc 24-volt lighting system Design in accordance with EU regulations ASPÖCK-UNIBOX on the front connection strip with 24N, 24S & 15-pin sockets Complete HRM metallization Complete steel construction shot blasted, then hot-finished with ZINACOR 850 Paint: 6-K final treatment: Complete steel construction shot blasted after welding 1 layer of zinc-based base paint, 1 layer of adhesion primer. Final painting with 2 layers of 2-K paint in one color in DB 7350 Nova gray, then sealing of the cavities with special wax Accessories: Bulkhead made of steel, pluggable, approx. 400 mm high Connection strip for supply lines to the tractor unit, attached at the height of the outer frame profile ASPÖCK-UNIBOX on the front connection strip with sockets 24N, 24S & 15-pin. If your pin assignment differs from the ISO connection standard, please let us know 3 kW electro-hydraulic unit for controlling the hydraulic processes, with the exception of hydraulic cable winches On the gooseneck 1 pair of plug-in aluminum side walls, approx. 400 mm high, in anodized design. 3.5" kingpin. Gooseneck guide plate for the fifth wheel plate, approx. 500 mm wide 2 brake shoes with bracket in front of the bulkhead. Mechanical seat supports with 2-speed gearbox and crank. Control valves for the hydraulic ramps on the right of the vehicle 1 pair of mechanical rear supports. Central lubrication system with 1 pump, brand BEKAMAX, with normal grease according to NLGI-2 Removable protection around the central lubrication pump(s) Steering from the front and rear can be operated using a cable remote control via push buttons, with alignment control of the axles, without installation in the tractor unit Under the gooseneck, as well as on the end cross member, left and right, one 7-pin socket with bracket for the warning signs A 7-pin socket on the end cross member Manual and description One INOX storage box, one-piece, approx. 2,480 x 340 x 390 mm in a straight design Please note that Special equipment and accessories generally increase the dead weight and reduce the payload accordingly Warning package: 4 warning signs, approx. 423 x 423 mm, extendable by approx. 1,000 mm, including 2 LED position lights and brackets for rotating beacon.

Condition: new, overall weight: 102,000 kg, empty load weight: 22,700 kg, maximum load weight: 79,300 kg, operation weight: 22,700 kg, axle configuration: > 3 axles, loading space length: 11,000 mm, loading space width: 2,850 mm, loading space height: 920 mm, color: grey, tire size: 245/70 R 17.5, Equipment: ABS, Gooseneck: -Gooseneck in SNT design to optimize the length of the loading area, length approx. 3,750 mm, with a bevel at the rear of approx. 850 mm x 10° -Can be raised and lowered hydraulically, stroke +- 250 mm including hydraulic connection connected to the hydraulic axle compensation of the first two axles -Open in the rear third -For tractor units: 6 x 4 and 8 x 4 Loading area: -Loading area in extendable design, length approx. 11,000 mm with a bevel at the rear of approx. 500 mm x 10°. -A recess in the loading area and in the bevel to accommodate the excavator bucket handle approx. 4,240 x 900 x 440 mm -Pneumatic locking with conical locking bolt and reinforced locking positions, the supply lines are protected in the extendable supports and automatically adjust to the respective loading area length Ramps: -A pair of two-part steel ramps with a length of approx. 4,650 mm and a width of approx. 900 mm -Hydraulically foldable ramp tips. -Ramps can be moved individually hydraulically by approx. 235 mm outwards and approx. 215 mm inwards -25 mm "Super Grip" rubber floor and approx. 5 mm sheet metal floor as additional reinforcement on the slope of the loading area -20x30 mm square climbing rails, approx. every 200 mm on the outer frame of the ramp Axles, suspension and tires: Iedpfx Abjk Af Svslobc -PA-X axle system, all axles hydro-mechanically forced steered -The steering behavior of the first two axles can be optimally adjusted to the length of the loading area both mechanically and hydraulically. -Hose rupture valve on the axle compensation cylinder with automatic RESET function. -Hydraulic cylinder with shut-off valves and pins for securing in the raised position. -245/70 R 17.5 3PMSF Accessories included: -Steel bulkhead, pluggable, approx. 400 mm high -Connection strip for supply lines to the tractor unit, mounted at the height of the outer frame profile -1 spare wheel -Outer support of the gooseneck with mounting holes for screwable lashing rings -The first hole approx. 200 mm from the front, then approx. every 400 mm -2 pairs of screwable lashing rings included -Checker plate covering above the gooseneck -On the gooseneck 1 pair of pluggable aluminum side walls on the side, approx. 400 mm high, anodized -On the gooseneck a pluggable aluminum rear wall, approx. 400 mm high, anodized -3.5" kingpin / 2" kingpin mounted -Guide plate from the gooseneck for the fifth wheel plate, approx. 500 mm wide -4 Brake shoes -4 axle load gauges -Mechanical downpipe supports at the front -1 one-piece INOX tool box, approx. 2,480 x 340 x 390 mm -Mechanical downpipe supports at the front -Continuous sheet metal covering on the loading area with a painted layer of sand to prevent slipping -1 intermediate table, approx. 500 mm wide, for the pull-out, with long holes for hanging and movable bridging elements -Painted sand coating on the support surfaces of the intermediate table -Mechanical locking for locking the intermediate table to the pull-out -8 pairs of stake pockets in the outer frame -Extensions (galvanized) extendable by approx. 230 mm per side -1 pair of hydraulic. Rear supports -Central lubrication system -1 reversing light on the left and right at the rear of the vehicle -3 kW electro-hydraulic unit -Widening planks, loose, in reinforced steel U-frame -Radio and cable remote control -4 warning signs, approx. 423 x 423 mm

Condition: new, overall weight: 49,500 kg, empty load weight: 7,900 kg, maximum load weight: 41,600 kg, operation weight: 7,900 kg, axle configuration: 3 axles, loading space length: 8,600 mm, loading space width: 2,540 mm, loading space height: 860 mm, suspension: air-lift, color: grey, tire size: 235/75 R 17,5, Equipment: ABS, Gooseneck: -Gooseneck with rear bevel of approx. 750 mm x 10° -3 pairs of lashing rings (LC 5,000 daN) -Hardwood decking 30 mm thick Loading area: -Loading surface with rear slope of approx. 1,000 mm x 8° -Recess in the chamfer and protruding into the loading surface to accommodate the excavator dipper stick approx. 2,900 x 750 x 210/290 mm Cut-outs in the outer frame of the cargo bed for attaching tensioning straps -Hardwood flooring approx. 48 mm thick, checker plate flooring over the axles Seat posts: -JOST fifth-wheel supports (mechanical) with 2-speed gearbox for 24 t lifting load (50 t test load) Axles and tires: -BPW axles and suspension, 2 axles rigid, 1 axle self-steering -Technical axle load: 12,000 kg -Electromagnetic reverse lock via reverse gear and can be activated manually -Air suspension with lifting and lowering valve -TPMS tire pressure monitoring system in accordance with ECE R 141 -235/75 R 17.5 tires Paint finish: -Complete steel construction automatically blasted after welding with blast wheel system -second blasting with corundum for optimum adhesion of the coating system -Finishing coat with 2 layers of 2K top coat, single color in RAL MB 7350 nova grey -Rims painted in silver -Rear section metallized and painted in RAL 9010 (pure white) -Sealing of cavities with special wax Electrical system: -Electrical system in accordance with EU regulations, lighting 24 volt ASPÖCK-NORDIK (ASS3) ASPÖCK-UNIBOX at the front connection strip with sockets 2x 7-pin & 1x15-pin Accessories included: -Extensive lashing positions -2" kingpin -One galvanized steel end wall approx. 400 mm high -Yellow-red air couplings on the galvanized connection strip at the front -4 restraining shoes with holder on the bulkhead -Mounting in the rear area of the gooseneck for ALU docking ramps -Galvanized folding supports under the bevel of the cargo bed -One bracket for a rotating beacon at the rear of the trailer -Galvanized extensions, extendable by approx. 230 mm per side Ibjdpfxjunrapj Abljc -White reflector tape in accordance with EU regulations on the sides and red at the rear -On the gooseneck and on the rear plate on the left and right, one bracket each for the warning signs including socket -ALU drop sides and rear panel can be plugged onto the gooseneck approx. 2,440 x 400 mm -The rear, galvanized stanchions are removable -2 pairs of WADER container pockets in the loading area for a 20ft container -6 pairs of stanchion pockets for 100 x 50 mm stanchions in the outer frame of the cargo bed -Sliding attachment strip for ALU docking ramps at the rear of the vehicle -Square climbing rails 20 x 20 mm every 200 mm on the outer frame of the loading area slope -a layer of sand painted onto the chequer plates on the gooseneck and on the cargo bed to prevent slipping -Four warning signs that can be extended by approx. 400 mm, approx. 423 x 423 mm with a position light -One bracket for rotating beacon on the warning signs -Speed sticker 80 km/h at the rear and on both sides -European reflector plates (red/yellow) at the rear of the trailer -Manual and description on USB stick -HRM metallization (High Resistance Metallization) of the outer frame -Complete steel construction shot-blasted, then the defined visible surfaces hot-finished in metallization with ZINACOR 850 (zinc 85% - aluminium 15%)

Condition: new, overall weight: 50,960 kg, empty load weight: 10,600 kg, maximum load weight: 39,400 kg, operation weight: 10,600 kg, axle configuration: > 3 axles, loading space length: 9,300 mm, loading space width: 2,540 mm, loading space height: 760 mm, suspension: air-lift, color: grey, tire size: 205/65 R17.5, Equipment: ABS, Gooseneck: -Gooseneck with hardwood covering, 30 mm thick -Gooseneck at the rear, straight design -3 pairs of lashing rings (LC 5,000 daN) Loading area in extendable design: -Loading area in extendable design -5 pairs of lashing rings that can be folded outwards -3 pairs of lashing rings that can be folded outwards -1 pair of lashing rings lying in the front of the loading area -Cutouts in the outer frame of the loading area for hanging tensioning straps -Hardwood covering, approx. 48 mm thick, checkered sheet covering over the axles Seatposts: -JOST seatposts (mechanical) with 2-speed gearbox for 24t lifting load (50t test load) Axles and tires: -BPW axles, two axles rigid, two axles with self-steering -Air suspension, with drum brake, with lifting/lowering- Function -The self-steering axles with electro-magnetic reversing lock can be activated via reverse gear or manually -Axle tool -Tires 205/65 R17.5 Braking system: -Braking system in accordance with EU regulations with EBS-E (4S3M) Steel construction: -Steel construction made of high-strength fine-grain steels -Steel qualities: -S355J2+N/S355MC (yield strength 355MPa) -S690QL/S700MC (yield strength 690MPa) Electrical system: -Electrical system in accordance with EU regulations, lighting 24 volts, ASPÖCK-NORDIK (ASS3) -ASPÖCK-UNIBOX on the front connection strip with 24N, 24S & 15-pin sockets -Connection in accordance with ISO: -24N ISO-1185 -24S ISO-3731 -15-pin ISO-12098 Painting: -First-class and long-lasting corrosion protection of the standard shot-blasted welded frame guaranteed by a 2-component (2K) zinc dust primer -A high-quality 2-component (2K) top coat in a single color in Nova gray -Rear section metallized and painted in RAL 9010 (pure white) Accessories included: -A spare wheel with holder in front of the bulkhead -2" kingpins -A galvanized steel bulkhead approx. 400 mm high -Yellow-red air couplings on the galvanized connection strip at the front -4 brake shoes with holder on the bulkhead -Galvanized folding supports under the bevel of the loading area Ibedjt Ag Uwspfx Ablsc -A bracket for a rotating beacon at the rear of the trailer -Galvanized extensions, extendable by approx. 230 mm on each side -White Reflective tape in accordance with EU regulations on the side, on the extension and at the rear, red -On the gooseneck and on the rear panel on the left and right, a holder for the warning signs including a socket -European reflector signs (red-yellow) on the rear of the trailer -TPMS tire pressure monitoring system in accordance with ECE R 141 -ALU side walls and rear wall can be plugged into the gooseneck, approx. 2,440 x 400 mm -The rear, galvanized plug-in stanchions are removable, length of the structure approx. 2,560 mm -7 pairs of WADER container bags -1x 20ft container in the loading area; 1x 40ft container in the loading area; 1x 40ft container above the gooseneck; 2x 20ft containers -7 pairs of stake pockets for 100 x 50 mm stakes in the outer frame of the loading area -Lift axle on the front axle with control by TEBS E depending on the current axle load and the current loading status -Movable mounting rail for aluminum loading ramps at the rear of the vehicle -A painted layer of sand on the checker plates on the gooseneck and on the loading area to prevent slipping -Four warning signs, approx. 423 x 423 mm, extendable by approx. 400 mm, with a position light -A holder for a rotating beacon on the warning signs -Speed sticker 80 km/h at the rear and on both sides -L

Condition: new, overall weight: 49,500 kg, empty load weight: 10,700 kg, maximum load weight: 38,800 kg, axle configuration: 3 axles, loading space length: 9,300 mm, loading space width: 2,540 mm, loading space height: 860 mm, suspension: air, color: grey-black, tire size: 235/75 r 17,5, Equipment: ABS, Gooseneck: •Gooseneck with bevelled corners at the front 45° and with a rear bevel of approx. 750 mm x 10° •3 pairs of lashing rings •Hardwood flooring 30 mm thick Loading area in extendable version: •Loading area in extendable version with rear bevel of approx. 1,000 mm x 8° •Cutouts in the outer frame of the loading area for hanging tensioning straps •Hardwood flooring approx. 48 mm thick, checkered sheet covering over the axles Two-part steel ramps: •One pair of galvanised, two-part steel ramps with approx. 48 mm thick hardwood flooring •Ramp with hydraulically foldable and unfoldable ramp parts, hydraulic lifting mechanism and hydraulically movable •Maximum load per pair: approx. 40,000 kg Axles and Tires: •BPW axles and suspension, 2 axles rigid, 1 axle with self-steering •Technical axle load: 12,000 kg •Electro-magnetic reversing lock can be activated via reverse gear and manually •Air suspension with lifting and lowering valve •Axle tool •235/75 R 17.5 3PMSF Brake system: •WABCO brake system in accordance with EU regulations with EBS-E Paintwork: •First-class and long-lasting corrosion protection of the standard shot-blasted welded frame guaranteed by a 2-component zinc dust primer •A high-quality 2-component top coat in one color in MB 7350 Nova gray •Rear section metallized and painted in RAL 9010 Seatposts: •JOST seatposts with 2-speed gearbox for 24t lifting load (50t test load). Steel construction: •Steel construction made of high-strength fine-grain steel •Steel qualities: •S355J2+N/S355MC •S690QL/S700MC Electrical system: •Electrical system in accordance with EU regulations, 24 volt lighting •ASPÖCK-UNIBOX on the front connection panel with 24N, 24S & 15-pin sockets Accessories included: •A spare wheel with holder •A galvanized steel bulkhead approx. 400 mm high •Yellow-red air couplings on the galvanized front connection panel •4 wheel chocks •A bracket for a rotating beacon at the rear of the trailer •Mounting in the rear area of the gooseneck for aluminum docking ramps •Galvanized folding supports under the bevel of the loading area •Cover plates to bridge the space between the ramps and the loading area •White Reflective tape in accordance with EU regulations on the side, on the extension and at the rear, red •Electro-hydraulic unit at the rear, under the loading area •A holder for the warning signs including a socket on the gooseneck and on the ramps on the left and right •Control valves for the ramps attached to the right-hand side of the trailer •ALU side walls and rear wall on the gooseneck, approx. 2,440 x 400 mm •The rear, galvanized plug-in stanchions are removable (length of the structure approx. 2,560 mm) •Four warning signs extendable by approx. 400 mm with a position light •3 pairs of WADER container pockets in the loading area for a 20ft, 30ft or 40ft container •6 pairs of stanchion pockets (100x50 mm) in the outer frame of the loading area •Galvanized extensions, extendable by approx. 230 mm each Page •Square climbing rails 20 x 20 mm every 200 mm on the outer frame of the loading area bevel •A painted layer of sand on the checker plates, above the kingpin and the loading area as anti-slip protection Iedpfx Ajhlz S Njblebc •Load pressure gauge for determining the axle loads including load diagram •HRM metallization (High Resistance Metallization) of the outer frame •Complete steel construction shot blasted, then the defined visible surfaces are hot-finished in metallization with ZINACOR 850 (zinc 85% - aluminum 15%)

Condition: new, overall weight: 48,000 kg, empty load weight: 11,400 kg, maximum load weight: 36,600 kg, axle configuration: 3 axles, loading space length: 13,100 mm, loading space width: 2,540 mm, loading space height: 860 mm, suspension: air, color: grey-black, tire size: 235/75 r 17,5, Equipment: ABS, Gooseneck: - Gooseneck in SNT design to optimize the loading area length, length approx. 3,700 mm - Rear gooseneck with bevel approx. 1,000 mm x 6°. - Technical fifth wheel load: 18,000 kg - For SZM: 4 x 2 or 6 x 2 Loading area: - Loading area, length approx. 9,400 mm, with rear chamfer approx. 900 mm x 6°. - Loading platform after the gooseneck, can be raised and lowered hydraulically. - Loading platform length approx. 3,000 mm. Loadable up to approx. 9,000 kg Ramps: - 1 pair of two-part hydraulic steel ramps, approx. 4,350 x 900 mm. - Hardwood decking. - Hydraulically folding ramp tips. - Ramps can be moved individually hydraulically by approx. 235 mm outwards and approx. 365 mm inwards. Axles and suspension: - BPW axles and suspension, two axles rigid, one axle self-steering. - Technical axle load: 12,000 kg - Electromagnetic reverse lock via reverse gear and manual activation. - Air suspension with lifting and lowering valve. - Axle tool. Tires: - 235/75 R 17.5 3PMSF dual tires. - Load index 143/141J (144/144F) Brake system: - WABCO EBS-E braking system in accordance with EU regulations. Lighting system: - 24-volt lighting system in "ASPÖCK-NORDIK full LED" (ASS 3) - Design in accordance with EU regulations. Metallization: - Standard HRM metallization (High Resistance Metallization) of the outer frame. - Complete steel construction shot-peened, then the defined visible surfaces metallized with - metallization with ZINACOR 850 (zinc 85% - aluminium 15%). Painting: Ibodpfjiuy Npox Ablec - 6-K final treatment: - Complete steel construction shot-blasted after welding. - One coat of zinc-based primer, one coat of adhesion primer. - Final coat with 2 layers of 2-component paint (acrylic) in one color in nova grey, followed by sealing of the cavities with special wax. Rims in silver. Steel construction: - Steel construction made of high-strength fine-grain steels. - Steel grades: S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa) Welder DIN-EN 287-1 tested. MAG welding process according to EN ISO 4063. Shielding gas M21 according to EN ISO 14175 Accessories included: - Steel end wall, pluggable, approx. 400 mm high. - Connection strip for supply lines to the SZM, attached at the height of the outer frame profile. - ASPÖCK-UNIBOX on the connection strip at the front with 24N, 24S & 15-pin sockets. 24N connection in accordance with ISO-1185 24S connection in accordance with ISO 3731 15-pin connection in accordance with ISO-12098 - 1 spare wheel with mounting adapter under the cargo bed on the right in front of the axles. - Parking position on the gooseneck for the warning signs when not in use. - Outer support of the gooseneck with fastening holes for screwable lashing rings. The first hole approx. 200 mm from the front, then approx. every 400 mm. 2 pairs of screw-in lashing rings included (LC 5,000 daN). - One fastening hole in the rear upper area of the outer beams of the gooseneck for a screw-in lashing ring. 1 pair of screw-in lashing rings included (LC 10,000 daN). - 1 pair of recessed lashing rings at the rear in the middle of the gooseneck (LC 5,000 daN). - 3 pairs of recessed lashing rings inside on the outer beam of the gooseneck (LC 5,000 daN) - 3 pairs of lashing rings in the middle of the gooseneck for (LC 5,000 daN). - Approx. 40 mm hardwood planking above the gooseneck. - 2" kingpin - On the gooseneck, 1 pair of plug-in aluminium side plates, approx. 400 mm high, in anodized finish. - On the gooseneck, one plug-in aluminum

Condition: new, overall weight: 60,800 kg, maximum load weight: 49,000 kg, axle configuration: > 3 axles, loading space length: 9,300 mm, loading space width: 2,540 mm, loading space height: 860 mm, suspension: air, color: grey, tire size: 235/75 r 17.5, Equipment: ABS, Gooseneck: -Gooseneck with beveled corners at the front 45° and with rear bevel of approx. 750 mm x 10° -3 pairs of lashing rings (LC 5,000 daN) -Hardwood decking 30 mm thick Loading area in extendable version: -Loading surface in extendable version with rear bevel of approx. 1,000 mm x 8° -5 pairs of lashing rings can be folded outwards (LC 5,000 daN) -3 pairs of lashing rings can be folded outwards (LC 10,000 daN) -1 pair of lashing rings lying in the front of the cargo bed (LC 10,000 daN) Cut-outs in the outer frame of the cargo bed for attaching lashing straps. (LC 2,000 daN) -Hardwood flooring approx. 48 mm thick, checker plate flooring over the axles Removable two-part ramps: -A pair of galvanized two-part steel ramps approx. 2,750 + 1,400 x 800 mm with approx. 48 mm thick hardwood decking -Ramp with hydraulically folding and unfolding ramp sections, hydraulic lifting gear and hydraulically movable -Maximum load per pair: 40,000 kg Seat posts: -JOST fifth wheels (mechanical) with 2-speed gearbox for 24 t lifting load (50 t test load) Axles and tires: -BPW axles, two axles rigid two axles self-steering, air-suspended, with drum brake, with lifting/lowering function The self-steering axles with electro-magnetic reverse lock can be activated via reverse gear or manually -axle tool -235/75 R 17.5 tires Brake system: -brake system in accordance with EU regulations with EBS-E (4S3M) Steel construction: -steel construction made of high-strength fine-grained steels -Steel grades: -S355J2+N/S355MC (yield strength 355MPa) -S690QL/S700MC (yield strength 690MPa) Coating: -First-class and durable corrosion protection of the standard shot-peened welded frame guaranteed by a 2-component (2K) zinc dust primer A high-quality 2-component (2K) top coat in a single color in nova grey Electrical system: -Electrical system in accordance with EU regulations, 24 volt ASPÖCK-NORDIK lighting (ASS3) ASPÖCK-UNIBOX on the front connection strip with 24N, 24S & 15-pin sockets Accessories included: -2" kingpin -One galvanized steel bulkhead approx. 400 mm high -One spare wheel with holder in front of the bulkhead -Yellow-red air couplings on the galvanized connection strip at the front -4 wheel chocks with holder on the bulkhead -Mounting in the rear area of the gooseneck for ALU docking ramps -Galvanized folding supports under the bevel of the cargo bed -One bracket for a rotating beacon -Cover plates to bridge the gap between ramps and cargo bed -White reflector tape in accordance with EU regulations on the sides, on the extension and red at the rear -Electric hydraulic unit -On the gooseneck and on the ramps on the left and right a holder for the warning signs including socket -Control valves for the ramps mounted on the right-hand side of the trailer -One mud flap at the rear of the trailer -Manual and description on USB stick -ALU drop sides and rear wall can be plugged onto the gooseneck approx. 2,440 x 400 mm -The rear galvanized stanchions are removable (length of the body approx. 2,560 mm) -4 pairs of WADER container pockets in the loading area for one 20ft, 2x 20ft or one 40ft container -7 pairs of stanchion pockets for 100 x 50 mm stanchions in the outer frame of the cargo bed -Galvanized extensions, extendable by approx. 230 mm per side -Lift axle on the front axle with controls -Square climbing rails 20 x 20 mm -BEKAMAX central lubrication system Isdpjh Etf Rsfx Ablebc -Four warning signs extendable by approx. 400 mm approx. 423 x 423 mm

Condition: new, overall weight: 49,500 kg, empty load weight: 10,300 kg, maximum load weight: 39,200 kg, axle configuration: 3 axles, loading space length: 9,300 mm, loading space width: 2,540 mm, loading space height: 860 mm, suspension: air, color: grey, tire size: 235/75 R 17.5, Equipment: ABS, Gooseneck: -gooseneck with rear bevel of approx. 750 mm x 10° -3 pairs of lashing rings (LC 5,000 daN) Ibedpsu Hp Hrsfx Ablsc -Hardwood decking 30 mm thick Loading area: -Loading surface can be raised and lowered hydraulically after the gooseneck Length approx. 2,800 mm, with rear slope of approx. 1,000 mm x 8° Cut-outs in the outer frame of the cargo bed for attaching tensioning straps (LC 2,000 daN) -Hardwood flooring approx. 48 mm thick, checker plate flooring over the axles Two-part steel ramps: -One pair of galvanized two-part steel ramps approx. 2,750 + 1,400 x 800 mm with approx. 48 mm thick hardwood decking -Ramp with hydraulically folding and unfolding ramp sections, hydraulic lifting gear and hydraulically movable -Maximum load per pair: 40,000 kg Axles, suspension and tires: -BPW axles and suspension, 2 axles rigid, 1 axle self-steering -Technical axle load: 12,000 kg -Electromagnetic reverse lock via reverse gear and can be activated manually -Air suspension with lifting and lowering valve -axle tool -235/75 R 17.5 3PMSF tires -TPMS tire pressure monitoring system in accordance with ECE R 141 Accessories included: -One spare wheel with holder in front of the bulkhead -2" kingpin -One galvanized steel bulkhead approx. 400 mm high -Yellow-red air couplings on the galvanized connection strip at the front -4 pieces of restraining shoes -Galvanized folding supports under the bevel of the cargo bed -A bracket for a rotating beacon at the rear of the trailer -Cover plates to bridge the space between the ramps and the cargo bed -White reflective tape in accordance with EU regulations on the side of the trailer and red at the rear -Electric hydraulic unit at the rear, under the cargo bed -One bracket for the warning signs on the gooseneck and on the ramps on the left and right, including socket -Control valves for the ramps fitted on the right-hand side of the trailer -European reflector signs (red/yellow) at the rear of the trailer -Manual and description on USB stick -ALU drop sides and rear wall can be plugged onto the gooseneck approx. 2,440 x 400 mm -The rear, galvanized stanchions are removable (length of the body approx. 2,560 mm) -An electric cable winch with radio remote control approx. 5,400 kg lifting force, including 9.5 mm thick wire rope 24 m long with rope guide roller -Screwed 5to ring for reeving the cable winch cable on the neck without deflection pulley -2 pairs of WADER container pockets in the loading area for a 20ft container -6 pairs of stanchion pockets for 100 x 50 mm stanchions in the outer frame of the cargo bed -Lift axle on the front axle with control by TEBS E depending on the current axle load and the current loading condition -7 pairs of recessed lashing rings along the central beam (LC 5,000 daN) -1 pair of recessed lashing rings along the central beam at the rear of the bevel (LC 10,000 daN) -A layer of sand painted onto the chequer plates on the gooseneck and on the cargo bed to prevent slipping -BEKAMAX (Pico) central lubrication system with NLGI-2 standard grease and removable protection around the pump -Four warning signs extendable by approx. 400 mm approx. 423 x 423 mm -Speed sticker 80 km/h at the rear and on both sides -Load manometer to determine the axle loads including load diagram -HRM metallization (High Resistance Metallization) of the outer frame -Complete steel construction shot-blasted, then the defined visible surfaces hot-finished in metallization with ZINACOR 850 (zinc 85% - aluminium 15%)

Condition: new, overall weight: 48,000 kg, empty load weight: 9,300 kg, maximum load weight: 38,700 kg, axle configuration: 3 axles, loading space length: 13,600 mm, loading space width: 2,540 mm, loading space height: 1,200 mm, suspension: air, color: grey-black, tire size: 385/65 R 22,5, Equipment: ABS, Cargo bed: - Load surface in extendable design with pneumatically operated locking mechanism - Loading area with approx. 30 mm thick wooden floor - 7 pairs of lashing rings can be folded outwards (LC 5,000 daN) - 3 pairs of lashing rings can be folded outwards (LC 10,000 daN) - Cut-outs in the outer frame of the cargo bed for attaching lashing straps. (LC 2,000 daN) Axles and tires: - BPW axles and suspension, all axles with hydro-mechanical forced steering - With disk brakes - Technical axle load: 10,000 kg - Air suspension with lifting and lowering valve - Axle tool - Tires: 385/65 R 22.5 - TPMS tire pressure monitoring system in accordance with ECE R 141 Brake system: - WABCO braking system in accordance with EU regulations with EBS-E (2S2M) Electrical system: Ibodpfoiu Etrsx Abloc - Electrical system in accordance with EU regulations, 24 volt ASPÖCK-NORDIK lighting (ASS3) - ASPÖCK-UNIBOX on the front connection strip with 24N, 24S & 15-pin sockets - Connection according to ISO - 24N ISO-1185 - 24S ISO-3731 - 15-pin ISO-12098 Accessories included: - Re-steering can be operated from the front and rear by cable remote control via pushbuttons, with toe-in control of the axles - 4 wheel chocks with holder on the front wall - 2" kingpin - One galvanized steel bulkhead approx. 1,600 mm high - Yellow-red air couplings on the galvanized connection strip at the front - White reflector tape in accordance with EU regulations on the side, on the extension and at the rear of the trailer in red - European reflector plates (red/yellow) at the rear of the trailer - A mud flap at the rear of the trailer - Manual and description - A bracket for a rotating beacon at the rear of the trailer - Loading area with approx. 30 mm thick wooden floor edged in omega profiles - 10 pairs of stanchion pockets for 100 x 50 mm stanchions in the outer frame of the cargo bed - 1 spare wheel holder under the cargo bed on the right in the direction of travel - Electro-hydraulic unit - On the gooseneck and on the rear panel on the left and right, one holder each for the warning signs including socket - A layer of sand painted onto the central beam to prevent slipping - 6 pairs of WADER container pockets in the loading area, for 1x20ft, 2x 20ft or 1x 40ft container, an additional locking point is provided in the pull-out for a 45ft container - 4 pairs of stanchion pocket rails, mounted transversely in the cargo bed, for 100 x 50 mm stanchions - Access ladder mounted on the right in the direction of travel - One HDPE tool box approx. 1,200 x 500 x 480 mm at the front under the cargo bed on the left in the direction of travel - Central lubrication system BEKAMAX (Pico) with removable protection around the pump - Lift axle on the front axle with control by TEBS E depending on the current axle load and the current load status - Radio remote control for steering in addition to the cable remote control, with indicator lights on the receiver for tracking control - Four warning signs extendable by approx. 400 mm approx. 423 x 423 mm with a position light - A holder for rotating beacon on the warning signs - Speed sticker 80 km/h at the rear and on both sides - Load manometer to determine the axle loads including load diagram - HRM metallization (High Resistance Metallization) of the outer frame - Complete steel construction shot-blasted, then the defined visible surfaces hot-finished in metallization with ZINACOR 850 (zinc 85% - aluminium 15%)

Condition: new, overall weight: 61,000 kg, empty load weight: 17,500 kg, maximum load weight: 43,500 kg, axle configuration: 3 axles, loading space length: 7,550 mm, loading space width: 2,750 mm, loading space height: 400 mm, color: grey, tire size: 245/70 R 17.5, Equipment: ABS, Gooseneck: -Gooseneck in SNT design to optimize the loading area length, length approx. 3,750 mm -Gooseneck can be raised/lowered and lowered hydraulically -For tractor units: 6x4 or 8x4 Drop deck: -Low bed with external beams in extendable design, "SUPER LOW" design, length approx. 7,550 mm -Low bed with solid hardwood floor approx. 40 mm thick and mechanical locking mechanism The supply lines are protected in the pull-out supports and automatically adjust to the respective drop-down bed length Rear chassis: -Rear chassis with closed outer frame, checker plate covering and continuous Prisma excavator trough approx. 1,450/900 x 505 mm, open at the rear Iodpoh Hm Thsfx Ablsbc -2 pairs of stanchion pockets for 100 x 50 mm stanchions in the outer frame Axles and tires: -"PENDEL-AXLE", all axles with hydromechanical forced steering -Hose rupture valve on the axle compensation cylinder with automatic RESET function -Hydraulic cylinder with stopcocks and locking pin for securing in raised position -Technical axle load: 12,000 kg -Hydraulic axle compensation -245/70 R 17.5 / 3PMSF tires Accessories included: -Preparation for mounting bolt-on container positioners for 1x 20ft or 1x 40ft container on the outer beams -2" kingpin -One galvanized steel end wall approx. 400 mm high -One spare wheel with holder -Yellow-red air couplings on the galvanized connection strip at the front -4 wheel chocks -Steering can be operated from the front and rear by remote control cable via pushbuttons, with axle tracking control -Hydraulic connections from the gooseneck to the low bed with multi-coupling instead of screw coupling -Electric hydraulic unit -White reflector tape in accordance with EU regulations on the side, on the extension and red at the rear -2 wooden blocks 500x250x200 mm -European reflector plates (red/yellow) at the rear of the trailer -On the gooseneck and on the rear plate on the left and right, one holder each for the warning signs including socket -Central lubrication system with 2 BEKAMAX (Pico) pumps with NLGI-2 standard grease -Load manometer for determining the axle loads including load diagram -ALU drop sides and rear wall can be plugged onto the gooseneck approx. 2,000 x 400 mm -The rear galvanized stanchions are removable (length of the body approx. 2,120 mm) -Separate air connection with air gun on the gooseneck -Duomatic air coupling from gooseneck to low bed -Gooseneck closed in the rear upper area with a removable cover -1 pair of steel ramps for bridging the mounting hooks of the low bed -Four warning panels approx. 423 x 423 mm, extendable by approx. 400 mm -Radio remote control for steering in addition to the cable remote control, with indicator lights on the receiver for tracking control 6 pairs of threaded blocks between the lashing rings under the top chord on the outer beam for mounting screw-on RUD rings VLBG-4 -7 pairs of stanchion pockets for 100 x 50 mm stanchions in the outer frame of the cargo bed -folding extensions, approx. 230 mm on each side -A layer of sand painted onto the loading surface to prevent slipping Dipper arm recess of the rear chassis closed at the front and rear with a plug-in plate -HRM metallization (High Resistance Metallization) of the outer frame -Complete steel construction shot-blasted, then the defined visible surfaces hot-finished with ZINACOR 850 metallization (zinc 85% - aluminium 15%)

Condition: new, overall weight: 63,000 kg, empty load weight: 15,550 kg, maximum load weight: 47,450 kg, axle configuration: 3 axles, loading space length: 8,800 mm, loading space width: 2,540 mm, loading space height: 860 mm, suspension: air, color: grey, tire size: 235/75 R 17,5, Equipment: ABS, Gooseneck: -Gooseneck in SNT design to optimize the loading area length, length approx. 3,700 mm -Rear gooseneck with bevel approx. 1,000 mm x 10° Loading area: -Loading area in extendable design, length approx. 8,800 mm, with bevel at the rear approx. 500 mm x 10° -One recess protruding into the loading surface and into the chamfer to accommodate the excavator dipper arm -Pneumatic locking with conical locking pins and reinforced locking positions -Hardwood covering on the bevel of the loading area Ibedpjk Aht Uefx Abloc Ramps: -1 Pair of two-part steel ramps with a length of approx. 4,350 mm and a width of approx. 900 mm -Ramps with hardwood decking -Hydraulically folding ramp tips -Ramps can be moved individually hydraulically by approx. 235 mm outwards and approx. 215 mm inwards -Square climbing ledges 20 x 30 mm, approx. every 200 mm on the outer frame of the ramp Axles and suspension: -BPW axles and suspension, 1st axle with preload steering, all other axles with forced hydromechanical steering -Technical axle load: 12,000 kg -1st axle with electromagnetic reverse lock via reverse gear and can be activated manually -Air suspension with lifting and lowering valve -235/75 R 17.5 twin tires -TPMS tire monitoring system in accordance with ECE R141 -TPMS tire monitoring sensors mounted in all wheels including spare wheels Accessories included: -steel front wall, pluggable, approx. 400 mm high -3 kW electro-hydraulic unit for controlling the hydraulic processes, with the exception of hydraulic cable winches -Parking position on the gooseneck for the warning signs when not in use -1 Spare wheel -On the gooseneck 1 pair of plug-in ALU side panels, approx. 400 mm high, anodized -One plug-in ALU rear panel on the gooseneck, approx. 400 mm high, anodized -Approx. 40 mm thick hardwood covering over the gooseneck, checker plate covering over the kingpin -2" kingpin -Guide plate from the gooseneck for the saddle plate, approx. 500 mm wide -4 wheel chocks -Mechanical seat posts with 2-speed gearbox and crank -JOST module B - static test load = 50,000 kg -1 Intermediate table, approx. 300 mm wide -Widenings (galvanized) extendable by approx. 230 mm per side -Wheel recesses with square climbing rails -ALU covers for the wheel recesses -1 pair of mechanical rear supports -Steering can be operated from the front and rear by cable remote control, with tracking control of the axles -1st axle with automatic lift axle function -Central lubrication system with 1 pump, BEKAMAX brand -Radio remote control for operating the self-steering, in addition to the cable remote control, with 2 indicator lights on the receiver as toe-in control -Wabco Smart Board System -4 warning signs, approx. 423 x 423 mm, extendable by approx. 400 mm, incl. 2 position lights and brackets for rotating beacon

Condition: new, overall weight: 69,500 kg, empty load weight: 13,500 kg, maximum load weight: 51,500 kg, axle configuration: > 3 axles, loading space length: 8,800 mm, loading space width: 2,540 mm, loading space height: 860 mm, suspension: air, color: grey, tire size: 235/75 r17.5, Equipment: ABS, Gooseneck: Gooseneck in SNT design to optimize the loading area length, length approx. 3,700 mm Rear gooseneck with bevel approx. 1,000 mm x 10° Cargo bed: Telescopic cargo bed, length approx. 8,800 mm, with rear chamfer approx. 500 mm x 10° Recess in the chamfer and protruding into the loading area to accommodate the excavator dipper arm Pneumatic locking with conical pin and reinforced locking positions The supply lines are protected in the extendable carrier and adapt to the respective loading area length Ramps: 1 pair of two-part steel ramps, approx. 4,350 mm x 900 mm Hydraulically folding ramp tips Ramps can be moved individually hydraulically outwards by approx. 235 mm and inwards by approx. 215 mm Axles and suspension: BPW axles and suspension, two axles rigid, two axles self-steering Electromagnetic reverse lock via reverse gear and can be activated manually Air suspension with lifting and lowering valve Axle tool Tires: 235/75 R17.5 3PMSF dual tires Load index: 143/141J (144/144F) Brake system: WABCO brake system, EBS-E in accordance with EU regulations Lighting system: 24-volt lighting system in "ASPÖCK-NORDIK full LED" Metallization: Standard HRM metallization of the outer frame Complete steel construction shot-peened, then the defined visible surfaces hot-finished with ZINACOR 850 (zinc 85% - aluminum 15%) metallization Steel construction: Steel grades: S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa) Welder DIN-EN 287-1 tested MAG welding process according to EN ISO 4063 Shielding gas M21 according to EN ISO 14175 Accessories included: Steel front wall, pluggable, height approx. 400 mm ASPÖCK-UNIBOX on the front connection strip with 24N, 24S & 15-pin sockets 24N connection in accordance with ISO-118524S connection in accordance with ISO-373115-pin connection in accordance with ISO-12098 Round NATO socket on the front connection strip Cable to supply the electro-hydraulic unit and/or the electric cable winch (35 mm2, 3.5 m long) between trailer and SZM with plug (NATO-NATO) Ibsdpfxok Ahugj Ablec 3 kW electro-hydraulic unit for controlling the hydraulic processes, with the exception of hydraulic cable winches 1 spare wheel with mounting adapter Outer support of the gooseneck with fastening holes for screw-in lashing ringsThe first hole approx. 200 mm from the front, then approx. every 400 mm 2 pairs of screw-in lashing rings included One fastening hole in the rear upper area of the outer beams of the gooseneck for a screw-in lashing ring 1 pair of screw-in lashing rings Approx. 40 mm thick hardwood covering above the gooseneck On the gooseneck 1 pair of plug-in aluminium drop sides on the side, approx. 400 mm high, anodized One plug-in aluminium rear panel on the gooseneck, approx. 400 mm high, anodized 2" kingpin Guide plate from the gooseneck for the saddle plate, approx. 500 mm wide 4 wheel chocks with holder Holder for ALU docking lights Mech. Saddle supports with 2-speed gearbox and crank Continuous hardwood covering on the cargo bed, interrupted between the axles, approx. 50 mm thick Locking of the cargo bed with conically welded locking profiles every 250 mm incl. pretensioning plate Slotted holes for attachable and movable bridging elements on the front of the cargo bed 1 intermediate table with stepped loading surface, approx. 300 mm wide for the pull-out tube with large cross-section with sheet metal covering Front and rear with Langl

Condition: new, overall weight: 49,500 kg, maximum load weight: 38,800 kg, axle configuration: 3 axles, loading space length: 9,300 mm, loading space width: 2,540 mm, loading space height: 860 mm, suspension: air, color: grey, tire size: 235/75 R 17,5 3PMSF, Equipment: ABS, Gooseneck: -Gooseneck with beveled corners at the front 45° and with rear bevel of approx. 750 mm x 10° -3 pairs of lashing rings (LC 5,000 daN) -Hardwood decking 30 mm thick Loading area in extendable version: -Loading surface in extendable version with rear slope of approx. 1,000 mm x 8° -6 pairs of lashing rings can be folded outwards (LC 5,000 daN) -3 pairs of lashing rings can be folded outwards (LC 10,000 daN) -1 pair of lashing rings lying in the front of the cargo bed (LC 10,000 daN) Cut-outs in the outer frame of the cargo bed for attaching lashing straps (LC 2,000 daN) -Hardwood flooring approx. 48 mm thick, checker plate flooring over the axles Axles and tires: -PW axles and suspension, 2 axles rigid, 1 axle self-steering -Technical axle load: 12,000 kg -Electro-magnetic reverse lock via reverse gear and can be activated manually -Air suspension with lifting and lowering valve -axle tool -235/75 R 17.5 3PMSF Brake system: Ibsdpfouqlmnsx Ablec -WABCO brake system in accordance with EU regulations with EBS-E (2S2M) Seat posts: -JOST seat posts (mechanical) with 2-speed gearbox for 24t lifting load (50t test load) Accessories included: -One spare wheel with holder in front of the bulkhead -2" kingpin -One galvanized steel bulkhead approx. 400 mm high -Yellow-red air couplings on the galvanized connection strip at the front -4 wheel chocks with holder on the bulkhead -One bracket for rotating beacon at the rear of the trailer -Mounting in the rear area of the gooseneck for ALU trailer lights -Galvanized folding supports under the bevel of the cargo bed -Cover plates to bridge the space between the ramps and the cargo bed -White reflective tape in accordance with EU regulations on the sides, on the extension and red at the rear -Electric hydraulic unit at the rear, under the cargo bed -On the gooseneck and on the ramps on the left and right a holder for the warning signs including socket -Control valves for the ramps mounted on the right-hand side of the trailer -One mud flap at the rear of the trailer -Manual and description on USB stick -ALU drop sides and rear wall approx. 2,440 x 400 mm on the gooseneck -The rear, galvanized stanchions are removable (length of the body approx. 2,560 mm) -Four warning signs approx. 423 x 423 mm with one position light, extendable by approx. 400 mm -3 pairs of WADER container pockets in the loading area for a 20ft, 30ft or 40ft container -6 pairs of stanchion pockets 100x50 mm in the outer frame of the cargo bed -Galvanized extensions, extendable by approx. 230 mm per side -Square climbing rails 20 x 20 mm every 200 mm on the outer frame of the loading area slope -A layer of sand painted onto the chequer plates, above the kingpin and the cargo bed to prevent slipping -On the warning plates a holder for rotating beacon -European reflector plates (red/yellow) at the rear of the trailer -Speed stickers 80 km/h at the rear and on both sides -Load manometer to determine the axle loads including load diagram -HRM metallization (High Resistance Metallization) of the outer frame -Complete steel construction shot-blasted, then the defined visible surfaces hot-finished in metallization with ZINACOR 850 (zinc 85% - aluminium 15%)

Condition: new, overall weight: 49,500 kg, empty load weight: 11,000 kg, maximum load weight: 38,500 kg, axle configuration: 3 axles, loading space length: 9,300 mm, loading space width: 2,540 mm, loading space height: 860 mm, suspension: air-lift, color: grey, tire size: 235/75 R 17,5, Gooseneck: -Gooseneck with rear bevel of approx. 750 mm x 10° -3 pairs of lashing rings (LC 5,000 daN) -Hardwood decking 30 mm thick Loading area: -telescopic loading area with rear slope approx. 1,000 mm x 8° -1 pair of fixed wheel recesses in front of the axles approx. 2,850 x 970 x 400 mm -Wheel recesses with square climbing strips 15 x 15 mm and widenings in the lower area -A pair of fixed wheel recesses with cover between the 1st and 2nd axle, approx. 1,610 x 970 x 400 mm -Recess in the chamfer and protruding into the loading area to accommodate the excavator dipper stick, approx. 2,900 x 750 x 210/290 mm -1 pair of lashing rings lying in the front of the cargo bed (LC 10,000 daN) -5 pairs of lashing rings foldable outwards (LC 5,000 daN) -2 pairs of lashing rings can be folded outwards (LC 10,000 daN) Cut-outs in the outer frame of the cargo bed for attaching lashing straps. (LC 2,000 daN) -incl. 3 removable galvanized covers over the wheel recesses - max. point load 3.5 to / pc. Hydr. two-part steel ramps: -One pair of galvanized two-part steel ramps approx. 2,750 + 1,400 x 800 mm with approx. 48 mm thick hardwood decking -Ramp with hydraulically folding and unfolding ramp sections, hydraulic lifting gear and hydraulically movable Axles and tires: -PW axles and suspension, 2 axles rigid, 1 axle self-steering -Technical axle load: 12,000 kg Ibodeup U Hzopfx Ablsc -Electromagnetic reverse lock via reverse gear and can be activated manually -Air suspension with lifting and lowering valve -axle tool -235/75 R 17.5 tires Accessories included: -2" kingpin -One galvanized steel bulkhead approx. 400 mm high -One spare wheel with holder in front of the bulkhead -Yellow-red air couplings on the galvanized connection strip at the front -4 wheel chocks with holder on the bulkhead -Mounting in the rear area of the gooseneck for ALU docking lights -Galvanized extensions, extendable by approx. 230 mm per side -Galvanized folding supports under the bevel of the cargo bed -One bracket for a rotating beacon at the rear of the trailer -White reflector tape in accordance with EU regulations on the sides, on the pull-out and red at the rear -One bracket for the warning signs including socket on the gooseneck and on the left and right rear plate -One mud flap at the rear of the trailer -European reflector plates (red/yellow) at the rear of the trailer -ALU drop sides and rear wall pluggable onto the gooseneck approx. 2,440 x 400 mm -The rear galvanized stanchions are removable (length of the body approx. 2,560 mm) -2 pairs of WADER container pockets in the loading area for a 20ft or 30ft container -3 pairs of stanchion pockets for 100 x 50 mm stanchions in the outer frame of the cargo bed -One removable galvanized intermediate table with 1 pair of WADER container pockets -Square climbing rails 20 x 20 mm every 200 mm on the outer frame of the loading area slope -Four warning signs approx. 423 x 423 mm, extendable by approx. 400 mm, with a position light -One bracket for rotating beacon on the warning signs -Speed sticker 80 km/h at the rear and on both sides -Load manometer for determining the axle loads including load diagram -HRM metallization (High Resistance Metallization) of the outer frame. -Complete steel construction shot-blasted, then the defined visible surfaces hot-finished in metallization with ZINACOR 850 (zinc 85% - aluminium 15%) Optionally available: -A toolbox on the gooseneck

Condition: new, overall weight: 49,500 kg, empty load weight: 10,350 kg, maximum load weight: 39,150 kg, axle configuration: 3 axles, loading space length: 9,300 mm, loading space width: 2,540 mm, loading space height: 860 mm, suspension: air/air, color: grey, tire size: 235/75 R 17,5, Equipment: ABS, Gooseneck: -Gooseneck with rear bevel of approx. 750 mm x 10° -3 pairs of lashing rings (LC 5,000 daN) -Hardwood decking 30 mm thick Loading area: -telescopic loading area with rear slope approx. 1,000 mm x 8° Ibsdpfxjiu Er Ao Abljc -1 pair of fixed wheel recesses in front of the axles approx. 2,850 x 970 x 400 mm -Wheel recesses with square climbing strips 15 x 15 mm and widenings in the lower area -A pair of fixed wheel recesses between the 1st and 2nd axles, approx. 1,610 x 970 x 400 mm -3-piece removable galvanized covers over the wheel recesses (W 670 mm) - max. point load 5 to / pc. -Recess in the chamfer and protruding into the loading area to accommodate the excavator dipper stick approx. 2,900 x 750 x 210/290 mm -1 pair of lashing rings lying in the front of the loading area (LC 10,000 daN) -5 pairs of lashing rings foldable outwards (LC 5,000 daN) -2 pairs of lashing rings can be folded outwards (LC 10,000 daN) -2 pairs of lashing rings in the excavator trough (LC 5,000 daN) Cut-outs in the outer frame of the cargo bed for attaching lashing straps (LC 2,000 daN) One-piece ALU ramps: -One pair of one-piece ALU ramps approx. 2,500 x 600 mm -Ramp with spring lifting mechanism and manually adjustable -Maximum load per pair: 24,000 kg Axles and tires: -BPW axles and suspension, 2 axles rigid, 1 axle self-steering -Technical axle load: 12,000 kg -Electromagnetic reverse lock via reverse gear and can be activated manually -Air suspension with lifting and lowering valve -axle tool -235/75 R 17.5 tires -TPMS tire pressure monitoring system in accordance with ECE R 141 Accessories included: -One spare wheel with holder in front of the bulkhead -2" kingpin -One galvanized steel bulkhead approx. 400 mm high -Yellow-red air couplings on the galvanized connection strip at the front -4 wheel chocks with holder on the bulkhead -Mounting in the rear area of the gooseneck for ALU docking lights -Galvanized extensions, extendable by approx. 230 mm per side -Galvanized folding supports under the bevel of the cargo bed -One bracket for a rotating beacon at the rear of the trailer -White reflector tape in accordance with EU regulations on the sides, on the pull-out and red at the rear -One bracket for the warning signs including socket on the left and right of the gooseneck and on the rear panel -ALU drop sides and rear wall can be plugged onto the gooseneck approx. 2,440 x 400 mm -The rear galvanized stanchions are removable (length of the body approx. 2,560 mm) -2 pairs of WADER container pockets in the loading area for a 20ft or 30ft container -3 pairs of stanchion pockets for 100 x 50 mm stanchions in the outer frame of the cargo bed -One removable galvanized intermediate table with 1 pair of WADER container pockets -Square climbing rails 20 x 20 mm every 200 mm on the outer frame of the loading area slope -a layer of sand painted onto the chequer plates on the gooseneck and on the loading area to prevent slipping -Four warning signs approx. 423 x 423 mm, extendable by approx. 400 mm, with a position light -A bracket for a rotating beacon on the warning signs -Speed sticker 80 km/h at the rear and on both sides -Load manometer for determining the axle loads including load diagram -HRM metallization (High Resistance Metallization) of the outer frame -Complete steel construction shot-blasted, then the defined visible surfaces hot-finished in metallization with ZINACOR 850 (zinc 85% - aluminium 15%)