Used Faymonville Max Semitrailers for sale (180)

Condition: new, maximum load weight: 36,040 kg, overall weight: 53,000 kg, axle configuration: 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory with vehicles available immediately and in the short term on our website. Excerpt from the equipment list. Complete equipment list available upon request. Gooseneck: * Gooseneck in SNT design to optimize the loading area length, length approx. 3,750 mm * Gooseneck hydraulically raisable/lowerable and extendable * For tractor unit: 6 x 4 or 8 x 4 Low-bed: * Low-bed with external beams in an extendable SUPER LOW design, length approx. 8,000 mm * Low-bed with a fixed hardwood floor approx. 40 mm thick and mechanical locking system * The supply lines are protected in the extendable beams and automatically adjust to the respective low-bed length * 7 pairs of lashing rings that can be folded outwards (LC 10,000 daN) * 6 pairs of threaded blocks on the inner beam for mounting screw-on RUD rings Rear chassis: * Rear chassis with closed outer frame and diamond plate cover * Chassis with excavator bucket, which is closed in the rear half to accommodate the air tanks * 3 pairs of lashing rings that can be folded outwards (LC 5,000 daN) * 1 pair of lashing rings that can be folded outwards (LC 10,000 daN) * 1 pair of lashing rings, horizontally, at the front and rear of the chassis (LC 10,000 daN) Axles: * BPW axles and suspension, all axles hydro-mechanically forced-steered * Technical axle load: 12,000 kg each * Air suspension with lifting and lowering valve Tires: * Tires 245/70 R 17.5 3PMSF - at the manufacturer's choice. Load index (146/146F) Braking system: * WABCO braking system in accordance with EU regulations with EBS-E (2S2M) Gksdsy Uwu Iepfx Apqsa Paint: * HRM metallization of the entire vehicle chassis with ZINACOR 850 (85% zinc/15% aluminum) to ensure the best corrosion protection * Topcoat with 2 layers of 2K topcoat, solid color in RAL 3002 carmine red, according to the RAL 841GL system Includes accessories: * 2-inch kingpin * One galvanized steel front bulkhead, approx. 400 mm high * Yellow-red air couplings on the galvanized connection strip at the front * Trailer steering, operable from the front and rear via cable remote control with push buttons, with single-axle steering control (without installation in the tractor unit) * Preparation for mounting screw-on container positioning for 1 x 20', 1 x 40' or 1 x 45' containers on the outer beams. Without container locking mechanisms * Hydraulic connections from the gooseneck to the low-bed with multi-coupling instead of screw couplings * Electro-hydraulic unit * Spiral cable for supplying the electro-hydraulic unit and/or the electric winch (approx. 35 mm², approx. 3.5 m long, max. 250A) between the semi-trailer and the tractor unit with plug connection (NATO-NATO) * Yellow reflector tape according to EU regulations on the side, on the extension and at the rear of the semi-trailer * On the gooseneck and at the rear, left and right, one bracket each for the warning signs, including a socket * Manual and description on a USB stick * Central lubrication system with 2 BEKAMAX (Pico) pumps with standard grease NLGI-2 and removable protection around the pumps * 7 pairs of threaded blocks between the lashing rings under the top chord on the outer beam for mounting screw-on RUD VLBG-4 rings * 2nd driving height, approx. 50 mm above the normal driving position, by means of manual operation * On the gooseneck, plug-in aluminum side panels and rear panel, approx. 2,440 x 400 mm (L x H). The rear, galvanized plug-in frames are removable (length of the superstructure

Condition: good (used), machine/vehicle number: YAFTL6002R0035345, loading space length: 14,800 mm, loading space width: 2,500 mm, loading space height: 9,000 mm, Year of construction: 2024, = Additional options and accessories = - Rear air suspension - Front air suspension Gsdpfxox Rtiaj Apqeka - Drum brake system = Further information = Payload: 81,100 kg Gross Vehicle Weight (GVW): 81,100 kg Technical condition: good Visual condition: good Front tyre condition: 60 Front tyres: 245/70 R17.5 Rear tyres: 245/70 R17.5 Last inspection: 2025-12-28 Contact Lastas Sales for further information.

Condition: good (used), axle configuration: 3 axles, permissible axle load (axle 1): 10,700 kg, permissible axle load (axle 2): 10,700 kg, permissible axle load (axle 3): 10,700 kg, first registration: 03/2013, suspension: air, tire size: 235/75R17.5, color: red, Year of construction: 2013, = Additional Options and Equipment = - Air suspension = Notes = Faymonville Euro low-loader with detachable gooseneck for sale Specifications 4 wheel recesses, each 2 meters Width: 2.55 m Extensions: 0.25 m Low bed: 8 meters Deck above the axles: 4.30 m Gooseneck top: 3.10 m Loading height (driving position): 0.50 m German registration Tires at 80 percent SAF axles Gkedpfx Apeyw Sxtsqoa 3 steering axles Robust and well-maintained low-loader, immediately ready for heavy-duty transport. = Further Information = Axle configuration Tire size: 235/75R17.5 Axle brand: SAF Suspension: Air suspension Rear axle 1: twin tires; max. axle load: 10,700 kg; steered; tire tread left inner: 70%; left outer: 70%; right inner: 70%; right outer: 70% Rear axle 2: twin tires; max. axle load: 10,700 kg; steered; tire tread left inner: 70%; left outer: 70%; right inner: 70%; right outer: 70% Rear axle 3: twin tires; max. axle load: 10,700 kg; steered; tire tread left inner: 70%; left outer: 70%; right inner: 70%; right outer: 70% Weights Unladen weight: 14,700 kg Payload: 17,400 kg Gross vehicle weight: 32,100 kg Condition Technical condition: good Visual condition: good Product Safety Manufacturer: Faymonville BE Additional Information Contact Gerrit Haverhoek for further information.

Condition: excellent (used), first registration: 09/2015, loading space length: 20,180 mm, loading space width: 3,000 mm, color: other, Year of construction: 2015, Damages: none YAFTL2007F0017329 = More information = Empty weight: 13.600 kg Carrying capacity: 28.400 kg GVW: 42.000 kg Technical condition: very good Visual appearance: very good Price: On request Registration number: DW205AH = Dealer information = Gkjdpeymrb Ssfx Apqsa Do you have any questions or suggestions? Please feel free to contact us. We guarantee a response within 8 hours. Prices do not include VAT. No rights may be derived from the information provided. Office phone number: Mobile: Dutch - English - German - French - Spanish - Italian) Available via WhatsApp and Viber. Mobile: Available via WhatsApp and Viber. When paying by bank transfer, the funds must be transferred to our bank account listed below. Always verify the payment details on our website. Please contact us if you have received different information. If in doubt, please call us so we can verify the invoice and/or payment. Bank details: Bank name: ING Bank address: Bijlmerdreef 106 1102 CT Amsterdam IBAN number: NL97INGB0117176699 EORI/VAT/TAX: NL810574901B(01) BIC/SWIFT: INGBNL2A

Condition: new, empty load weight: 15,550 kg, maximum load weight: 47,450 kg, overall weight: 63,000 kg, axle configuration: 3 axles, loading space length: 8,800 mm, loading space width: 2,540 mm, loading space height: 860 mm, suspension: air, tire size: 235/75 R 17,5, color: grey, Equipment: ABS, Gooseneck: -Gooseneck in SNT design for optimized loading area length, approximately 3,700 mm long -Gooseneck with rear bevel approximately 1,000 mm x 10° Loading Platform: -Loading platform in extendable design, approximately 8,800 mm long, with bevel at the rear approximately 500 mm x 10° -Recess in the loading platform and into the bevel for accommodating the excavator arm -Pneumatic locking system with tapered locking pins and reinforced locking positions -Hardwood decking on the bevel of the loading platform Ramps: -1 pair of two-part steel ramps with a length of approximately 4,350 mm and a width of approximately 900 mm -Ramps with hardwood decking -Hydraulically folding ramp ends -Ramps can be individually hydraulically moved outwards by approximately 235 mm and inwards by approximately 215 mm -Square ladder strips 20 x 30 mm, approximately every 200 mm on the outer frame of the ramp Axles and Suspension: -BPW axles and suspension, 1st axle with steering knuckle, all other axles with hydromechanical forced steering -Technical axle load: 12,000 kg -1st axle with electromagnetic reverse lock via reverse gear and can be activated manually -Air suspension with lifting and lowering valve -Tires 235/75 R 17.5, twin tires -TPMS tire monitoring system according to ECE R141 -TPMS tire monitoring sensors mounted in all wheels including spare wheel Included accessories: -Steel front wall, plug-in, approximately 400 mm high -3kW electro-hydraulic unit for controlling the hydraulic operations, with the exception of hydraulic winches -Parking position on the gooseneck for the warning signs when not in use -1 spare wheel -On the gooseneck, 1 pair of plug-in aluminum sideboards, approximately 400 mm high, anodized -On the gooseneck, 1 plug-in aluminum rear wall, approximately 400 mm high, anodized -Approximately 40 mm thick hardwood decking above the gooseneck, checkered plate decking above the kingpin -2" kingpin -Guide plate from the gooseneck for the fifth wheel plate, approximately 500 mm wide -4 chock blocks -Mechanical landing gear with 2-speed gearbox and crank Godpfx Apok Aht Usqoka -JOST Module B – static test load = 50,000 kg -1 intermediate table, approximately 300 mm wide -Extensions (galvanized), extendable by approximately 230 mm on each side -Wheel recesses with square ladder strips -Aluminum covers for the wheel recesses -1 pair of mechanical rear supports -Steering assistance at the front and rear, operable via cable remote control, with single-axle monitoring -1st axle with automatic lift axle function -Central lubrication system with 1 pump, brand BEKAMAX -Wireless remote control for operating the steering assistance, in addition to the cable remote control, with 2 indicator lights on the receiver for single-axle monitoring -Wabco Smart Board system -4 warning signs, approximately 423 x 423 mm, extendable by approximately 400 mm, incl. 2 position lights and mounts for rotating beacon

Condition: new, empty load weight: 12,300 kg, maximum load weight: 37,200 kg, overall weight: 49,500 kg, axle configuration: 3 axles, loading space length: 9,300 mm, loading space width: 2,480 mm, loading space height: 860 mm, suspension: air, tire size: 235/75 R17.5, color: grey, Equipment: ABS, Gooseneck: -Gooseneck with rear bevel of approx. 750 mm x 10° -Hardwood covering 30 mm thick Two-piece steel ramps: -A pair of galvanized two-part steel ramps approx. 3,185x1,420x1,250 mm with grating decking -Ramp with hydraulically folding and unfolding ramp sections, hydraulic lifting gear Gooseneck: -Gooseneck with rear bevel of approx. 750 mm x 10° -3 pairs of lashing rings -Hardwood decking 30 mm thick Two-part steel ramps: -One pair of galvanized two-part steel ramps approx. 3,185x1,420x1,250 mm with grating covering -Ramp with hydraulically folding and unfolding ramp sections, hydraulic lifting gear -Maximum load per pair: 30,000 kg Loading area: -Loading surface with rear slope of approx. 1,000 mm x 8° -Hardwood flooring approx. 48 mm thick, checker plate flooring over the axles Axles and tires: -BPW axles and suspension, two axles rigid, one axle self-steering -Air suspension with lifting and lowering valve The self-steering axles with electro-magnetic reverse lock can be activated via reverse gear or manually -235/75 R17.5 3PMSF tires Accessories included: -1 Spare wheel with holder -TPMS tire pressure monitoring system according to ECE R 141 -2" kingpin -Galvanized steel bulkhead -Yellow-red air couplings on the galvanized front connecting strip -4 restraining shoes with holder on the bulkhead -Mounting in the rear area of the gooseneck for ALU docking ramps -3 height aluminum boards -Galvanized folding supports under the bevel of the cargo bed Height-adjustable tarpaulin superstructure (3,960 mm) -Galvanized bulkhead with a tensioning mechanism for the sliding curtain -Height-adjustable by approx. 400 mm -"EDSCHA" brand roof can be moved forwards on ALU roof rail profiles bolted to the front and rear wall -3 pairs of sliding stanchions in the loading area -The body can be hydraulically widened at the rear to the left and right by approx. 750 mm -Sliding roof with pivoting portal support -Sliding tarpaulin with 700 mm reserve in length, with tension belts at approx. 600 mm intervals -Height top edge of body approx. 3,960 mm -Driving with the sliding tarpaulin open is not permitted and will damage the tarpaulin -Cover plates to bridge the free space between ramps and loading area -Electric hydraulic unit at the rear, under the cargo bed -On the gooseneck and on the ramps on the left and right, one bracket each for the warning signs including socket -Control valves for the ramps mounted on the right-hand side of the trailer -6 pairs of stanchion pockets for 100 x 50 mm stanchions in the outer frame of the cargo bed Gedpfotvfkfsx Apqjka -Lift axle on the front axle -Grating in the bevel of the loading area C40/4 (point load 3.4 tons on an area of 20 x 20 cm) -One INOX toolbox 565 x 290 x 810 mm in the direction of travel on the right between the axles -A layer of sand painted onto the chequer plates on the gooseneck and on the loading area to prevent slipping -BEKAMAX (Pico) central lubrication system with NLGI-2 standard grease and removable protection around the pump -Four warning panels approx. 423 x 423 mm, extendable by approx. 400 mm, with a position light -Load manometer for determining the axle loads including load diagram -HRM metallization (High Resistance Metallization) of the outer frame -Complete steel construction shot-blasted, then the defined visible surfaces hot-finished in metallization with ZINACOR 850 (zinc 85% - aluminium 15%)

Condition: new, empty load weight: 29,600 kg, maximum load weight: 72,400 kg, overall weight: 102,000 kg, axle configuration: > 3 axles, loading space length: 6,650 mm, loading space width: 2,840 mm, loading space height: 550 mm, tire size: 285/70 R19.5, color: grey, operation weight: 29,600 kg, Equipment: ABS, Gooseneck: -Hydraulic gooseneck Raisable/lowerable and removable -Length approx. 3,650 mm -For tractor units: 6 x 4 or 8 x 4 2-axle chassis at the front: -Hook attachments at the front and rear -Chassis length x chassis width approx. 2,200 mm x 2,850 mm Excavator bridge "BB-A": -Telescopic excavator bridge "BB-A" with drive-over bridge hooks at the front and with bolt-and-link coupling at the rear -Length x base width approx. 6,650 mm x 2,850 mm -Beam height x beam width approx. 400 mm x 1,350 mm -Loading height 550 mm with ground clearance 150 mm 4-axle chassis at the rear: -Mechanical bolt-and-link coupling for attaching a low bed at the front, end cross member at the rear -Chassis length x Chassis width approx. 5,480 mm x 2,850 mm - Extensive lashing positions Pendulum axle and tires (front and rear chassis): - "Pendulum axle", all axles hydromechanically steered - Hose rupture valve on the axle compensation cylinder with automatic reset function - Hydraulic cylinder with shut-off valves and pins for securing in the raised position - Final axle paint finish with two coats of 2-component paint in MB 7350 Nova Gray - Technical axle load: 12,000 kg - Hydraulic axle compensation - Tires 285/70 R19.5 Steering: - Front and rear steering can be operated via cable remote control using push buttons, with axle alignment control - Power socket for operating the steering system on the chassis Gooseneck -Cable remote control with pushbuttons including axle alignment control Accessories included: -Yellow-red air couplings on the galvanized connection strip at the front -Steel bulkhead, approx. 400 mm high -4 wheel chocks -3.5" kingpins -One 7-pin socket on the left and right rear of the gooseneck for the warning sign -Gallows with winch for spare wheel on the front of the gooseneck -Truck hydraulic connection with flow regulator (40 l/min), including a boom for suspending the supply lines. The tractor unit's tank must hold at least 80 liters with couplings -Aluminum side walls and rear wall that can be attached to the gooseneck, approx. 400 mm high, anodized -Control lever on the gooseneck protected by a hinged cover -A separate air connection with air gun on the gooseneck -Bekamax central lubrication system, 1x on the Gooseneck, 1x on the 2-axle chassis and 1x on the 4-axle chassis - Variomax tool kit - Multi-coupling hydraulic connections on the gooseneck and in the area of the low-loader hook attachment - 2 spare wheels - One 7-pin socket on the left and right, front and rear of the rear chassis for the warning sign - Front chassis with a separate air connection for pneumatic screwdrivers - Foldable extensions with steel mattresses, adjustable in width from approx. 2,850 mm to approx. 3,250 mm - The steel mattresses can be inserted in two positions to create a lowered loading area - Steel mattresses with rubber flooring, approx. 12 mm thick - Screw-in option (⌀ 40 mm) every approx. 500 mm outside on the upper chord of the outer tube of the excavator bridge for screw rings - One locking point every approx. 500 mm on the extension with mechanical locking Locking mechanism -A socket on the rear chassis for the cable remote control of the self-steering system Gedpfx Ajwcmhaspqoka -Two reversing lights on the rear panel -Four warning signs, approximately 423 x 423 mm, extendable by approximately 2,000 mm, with a position light -One work light, left and right, on the rear panel of the gooseneck with separate on/off switches -Two stainless steel tool boxes, approxim

Condition: new, empty load weight: 10,900 kg, maximum load weight: 37,100 kg, overall weight: 48,000 kg, axle configuration: 3 axles, loading space length: 9,600 mm, loading space width: 2,540 mm, loading space height: 890 mm, suspension: air, tire size: 235/75 R 17.5, color: grey, operation weight: 10,900 kg, Equipment: ABS, Gooseneck: -Gooseneck in SNT design to optimize the loading area length, length approx. 3,700 mm, with a bevel at the rear of approx. 1,000 mm x 6° -Technical fifth wheel load: 18,000 kg -For tractor units: 4 x 2 and 6 x 2 Loading area: -Loading area, length approx. 9,600 mm with a bevel at the rear of approx. 900 mm x 6° -Loading area can be raised and lowered hydraulically after the gooseneck, length approx. 3,000 mm, load capacity up to approx. 9,000 kg Gksdpfx Apouadk Noqsa -Grating and sheet metal floor approx. 5 mm as additional reinforcement on the bevel of the loading area Ramps: -A pair of two-part AXS steel ramps with a length of approx. 4,675 mm and a width of approx. 900 mm -Grating floor -Hydraulically hinged ramp tips -Ramps can be moved hydraulically by approx. 235 mm outwards and approx. 365 mm inwards -Painted sand coating on the outer frame of the ramp and on the ramp tip -Flashlights on the outside of the ramp tips with switch next to the ramp controls -Ramp secured in driving position using a quick release Axles, suspension and tires: -BPW axles and suspension, 1st and 2nd axle rigid, 3rd axle with self-steering -1st Axle with traction aid -Operation via the brake pedal in the tractor unit -Technical axle load: 12,000 kg -Air suspension with lifting and lowering valve -235/75 R 17.5 -TPMS tire pressure monitoring system in accordance with ECE R 141 -TPMS tire pressure monitoring sensors mounted in all wheels including spare wheels Braking system: -WABCO EBS-E brand braking system in accordance with EU regulations Paintwork: -Semi-trailer MB 7350 Nova gray Accessories included: -Bulkhead made of steel, plug-in, approx. 400 mm high -3 kW electro-hydraulic unit for controlling the hydraulic processes, with the exception of hydraulic cable winches -Guide plate from the gooseneck for the fifth wheel plate, approx. 500 mm wide -JOST module B - static test load = 50,000 kg -Continuous grating with 5 mm sheet metal underlay as additional reinforcement -Painted sand coating -Cutouts in the outer frame of the loading area and the lifting bed for hanging control valves for the hydraulic ramps on the right of the vehicle -2" kingpin -Central lubrication system with 1 pump, brand BEKAMAX -On the gooseneck 1 pair of plug-in aluminum side walls, approx. 400 mm high, anodized -Electric cable winch, approx. 5,400 kg pulling force, with radio remote control -Wire cable approx. 24 m long, cable ø approx. 9.5 mm, including cable pressure roller -WABCO Smart Board System -4 extendable warning signs, approx. 423 x 423 mm, extendable by approx. 400 mm

Condition: new, empty load weight: 13,500 kg, maximum load weight: 51,500 kg, overall weight: 69,500 kg, axle configuration: > 3 axles, loading space length: 8,800 mm, loading space width: 2,540 mm, loading space height: 860 mm, suspension: air, tire size: 235/75 r17.5, color: grey, Equipment: ABS, Gooseneck: Gooseneck in SNT design for optimizing the loading area length, length approx. 3,700 mm Rear gooseneck with bevel, approx. 1,000 mm x 10° Loading area: Telescoping loading area, length approx. 8,800 mm, with rear bevel approx. 500 mm x 10° Recess in the bevel and extending into the loading area for accommodating the excavator boom foot Pneumatic locking system with tapered pin and reinforced locking positions The supply lines are protected in the extendable beam and adapt to the respective loading area length Ramps: 1 pair of two-part steel ramps, approx. 4,350 mm x 900 mm Hydraulically folding ramp ends Ramps can be individually hydraulically moved outwards by approx. 235 mm and inwards by approx. 215 mm Axles and Suspension: BPW axles and suspension, two axles fixed, two axles with trailing arm steering Electromagnetic parking brake activated via reverse gear and manually Air suspension with raising and lowering valve Axle tool Tires: 235/75 R17.5 3PMSF, dual tires Load index: 143/141J (144/144F) Braking System: Braking system from WABCO, EBS-E according to EU regulations Lighting System: 24-volt lighting system in "ASPÖCK-NORDIK full LED" Metallization: Standard HRM metallization of the outer frame Complete steel construction shot-blasted, then the defined visible surfaces hot-dip metallized with ZINACOR 850 (Zinc 85% - Aluminum 15%) Steel Construction: Steel qualities: S355J2+N/S355MC (yield strength 355 MPa) S690QL/S700MC (yield strength 690 MPa) Welders certified according to DIN-EN 287-1 Welding process MAG according to EN ISO 4063 Shielding gas M21 according to EN ISO 14175 Included Accessories: Steel front wall, pluggable, height approx. 400 mm ASPÖCK-UNIBOX on the connection strip at the front with sockets 24N, 24S & 15-pin 24N connection according to ISO-1185, 24S connection according to ISO-3731, 15-pin connection according to ISO-12098 Round NATO socket on the connection strip at the front Cable for supplying the electro-hydraulic unit and/or the electric winch (35 mm2, 3.5 m long) between the semi-trailer and the drawbar trailer with plug (NATO-NATO) 3 kW electro-hydraulic unit for controlling the hydraulic operations, with the exception of hydraulic winches 1 spare wheel with mounting adapter Outer beam of the gooseneck with mounting holes for screwable lashing rings, the first hole approx. 200 mm from the front, then approx. every 400 mm 2 pairs of screwable lashing rings included One mounting hole in the rear upper area of the outer beam of the gooseneck for a screwable lashing ring 1 pair of screwable lashing rings Approx. 40 mm thick hardwood flooring above the gooseneck On the gooseneck, 1 pair of pluggable aluminum side panels, approx. 400 mm high, anodized On the gooseneck, one pluggable aluminum rear panel, approx. 400 mm high, anodized 2" kingpin Guide plate of the gooseneck for the saddle plate, approx. 500 mm wide 4 support wedges with holder Mounting for aluminum approach ramps Mechanical saddle supports with 2-speed gearbox and crank On the loading area, a continuous and interrupted between the axles hardwood flooring, approx. 50 mm thick Gsdpfxok Ahugj Apqoka Locking of the loading area with tapered welded locking profiles every 250 mm incl. pre-tensioning plate Elongated holes for hanging and adjustable bridging elements on the loading area at the front 1 intermediate table with recessed loading area, approx. 300 mm wide for the extension tube with large cross-section with sheet metal covering At the front and

Condition: new, empty load weight: 17,250 kg, maximum load weight: 48,700 kg, overall weight: 66,000 kg, axle configuration: 3 axles, loading space length: 7,550 mm, loading space width: 2,480 mm, loading space height: 375 mm, tire size: 245/70 R 17.5, color: grey, operation weight: 17,250 kg, Equipment: ABS, Gooseneck: -Gooseneck in SNT design for optimizing the loading platform length, length approx. 3,750 mm -Gooseneck hydraulically extendable/retractable and lowerable -For semi-trailer tractors: 6 x 4 and 8 x 4 (or 6 x 4 with optional 1-axle dolly) Lowboy: -Lowboy with external beams, designed as a telescoping boiler bridge with low construction and front extension -Length x width approx. 7,550 mm x 2,740 mm -Mechanical locking of the extension Chassis: -Rear chassis with closed outer frame -Diamond-plate surface and continuous prism-shaped excavator well approx. 1,450/900 x 505 mm, open at the rear Axles, suspension and tires: -“PENDEL-AXLE”, all axles hydromechanically forced steered -Hose rupture valve on the axle equalizing cylinder with automatic RESET function -Hydraulic cylinders with shut-off valves and quick-release couplings for securing in the raised position -Final coat of axles with 2 layers of 2-component paint in a single color, painted in “FAY-Gray-34-0260” -Technical axle load 12,000 kg -Hydraulic axle equalization -245/70 R 17.5 Accessories: -Steel front wall, plug-in type, approx. 400 mm high Gksdpjh Hm Tzsfx Apqja -4 pieces of chock blocks -Gooseneck with a removable cover closed at the rear upper area -1 pair of steel ramps with cleats and fastening bolts for bridging the pick-up hooks of the lowboy -The ramps can be positioned above or between the hooks -Mounting options for the steel access ramps at the rear between the outer beams of the gooseneck -A locking point approx. every 1,000 mm on the extension -1 lashing ring on the left and right on the front crossbeam -Connection bar for supply lines to the semi-trailer tractor, mounted at the height of the outer frame profile -6 pairs of threaded blocks on the outside of the inner beams of the loading platform for mounting screw-on rings M24 -6 pairs of recessed lashing rings on the outside of the outer beams of the loading platform, foldable inwards and outwards -1 pair of threaded blocks at the front and rear on the outer beams of the loading platform for mounting screw-on rings M24 -Mounting rail for loose ALU ramps on the end cross member of the vehicle -Central lubrication system with 2 pumps, brand BEKAMAX -Trailing steering from the front and rear, operable via cable remote control, with single-axle steering control -3 kW electro-hydraulic unit for controlling the hydraulic operations, with the exception of hydraulic winches -Removable loading floor (galvanized) can be inserted in 3 elements between the outer beams with hardwood surface -Folding widening elements, approx. 230 mm per side -Widening boards, loose, with steel edging -4 warning signs approx. 423 x 423 mm -Radio remote control for operating the trailing steering -3.5" kingpin -Anti-slip strips on the left slope of the gooseneck -Hydraulic connections from the gooseneck to the lowboy with multi-coupling instead of screw couplings -Guide plate from the gooseneck for the fifth wheel plate, approx. 800 mm wide -1 spare wheel with mounting adapter -Parking position on the gooseneck for the warning signs when not in use -2 pairs of pole pockets embedded in the outer frame of the chassis, for plug-in poles approx. 100 x 50 mm -Bucket arm recess of the rear chassis closed at the rear with a plug-in plate -Color of the semi-trailer MB 7350 Novagrau

Condition: new, empty load weight: 15,450 kg, maximum load weight: 65,550 kg, overall weight: 80,000 kg, axle configuration: > 3 axles, loading space length: 21,900 mm, loading space width: 2,540 mm, loading space height: 925 mm, suspension: air, tire size: 235/75 R 17.5, color: grey, Equipment: ABS, Gooseneck: Gooseneck in SNT design to optimize the loading area length, length approx. 3,700 mm, rear with bevel approx. 1,000 mm x 10° Technical fifth wheel load: 30,000 kg. For tractor units: 4x2, 6x2 and 6x4 Loading area: Loading area in double-extendable design, length approx. 8,800 mm with bevel at the rear approx. 500 mm x 10°. A support table approx. 300 mm wide with long holes at the front and rear for optional bridging elements that can be hung and moved is welded to the middle support. Pneumatic locking with conical locking bolt and reinforced locking positions, the supply lines are protected in the extendable supports and automatically adjust to the respective loading area length. Axles and tires: BPW axles and suspension, 1st axle with pre-steering, all other axles with hydro-mechanical forced steering. 1st axle with electro-magnetic reversing lock that can be activated via reverse gear and manually. Technical axle load: 12,000 kg Air suspension with lifting and lowering valve Manufacture of our choice Sockets and lighting: 24-volt lighting system Design in accordance with EU regulations ASPÖCK-UNIBOX on the front connection strip with 24N, 24S & 15-pin sockets Complete HRM metallization Complete steel construction shot blasted, then hot-finished with ZINACOR 850 Paint: 6-K final treatment: Complete steel construction shot blasted after welding 1 layer of zinc-based base paint, 1 layer of adhesion primer. Final painting with 2 layers of 2-K paint in one color in DB 7350 Nova gray, then sealing of the cavities with special wax Accessories: Godporigw Rjfx Apqoka Bulkhead made of steel, pluggable, approx. 400 mm high Connection strip for supply lines to the tractor unit, attached at the height of the outer frame profile ASPÖCK-UNIBOX on the front connection strip with sockets 24N, 24S & 15-pin. If your pin assignment differs from the ISO connection standard, please let us know 3 kW electro-hydraulic unit for controlling the hydraulic processes, with the exception of hydraulic cable winches On the gooseneck 1 pair of plug-in aluminum side walls, approx. 400 mm high, in anodized design. 3.5" kingpin. Gooseneck guide plate for the fifth wheel plate, approx. 500 mm wide 2 brake shoes with bracket in front of the bulkhead. Mechanical seat supports with 2-speed gearbox and crank. Control valves for the hydraulic ramps on the right of the vehicle 1 pair of mechanical rear supports. Central lubrication system with 1 pump, brand BEKAMAX, with normal grease according to NLGI-2 Removable protection around the central lubrication pump(s) Steering from the front and rear can be operated using a cable remote control via push buttons, with alignment control of the axles, without installation in the tractor unit Under the gooseneck, as well as on the end cross member, left and right, one 7-pin socket with bracket for the warning signs A 7-pin socket on the end cross member Manual and description One INOX storage box, one-piece, approx. 2,480 x 340 x 390 mm in a straight design Please note that Special equipment and accessories generally increase the dead weight and reduce the payload accordingly Warning package: 4 warning signs, approx. 423 x 423 mm, extendable by approx. 1,000 mm, including 2 LED position lights and brackets for rotating beacon.

Condition: new, empty load weight: 14,350 kg, maximum load weight: 53,450 kg, overall weight: 67,800 kg, axle configuration: > 3 axles, loading space length: 8,800 mm, loading space width: 2,540 mm, loading space height: 860 mm, suspension: air, tire size: 235/75 R 17,5, color: grey, Equipment: ABS, tail-lift, Gooseneck: - Gooseneck in SNT design for optimization of loading platform length, length approx. 3,700 mm - Rear gooseneck with bevel, approx. 1,000 mm x 10° - For tractor units: 6x2, 6x4, 8x4 short Loading Platform: - Extendable loading platform, length approx. 8,800 mm, with rear bevel approx. 500 mm x 10° - A recess in the loading platform and into the bevel to accommodate the excavator bucket arm, approx. 3,850 x 750 x 210/290 mm Two-Part Steel Ramps: - One pair of two-part steel ramps, length approx. 4,350 mm, width approx. 900 mm - Ramps with rubber covering - Ramps individually hydraulically movable approx. 235 mm outwards and approx. 215 mm inwards - "Super Grip" 25 mm rubber floor and steel plate floor approx. 5 mm as additional reinforcement on the platform bevel - Square climbing strips 20 x 30 mm, approx. every 200 mm on the outer frame of the ramp Gksdpfx Aoya E A Nepqsa Axles, Suspension, and Tires: - BPW axles and suspension, 1st axle steerable, all other axles hydromechanically forced-steered - Technical axle load: 12,000 kg - 1st axle with electromagnetic reversing lock, activatable via reverse gear and manually - Air suspension with lift and lower valve - Tires 235/75 R 17.5 - TPMS tire monitoring system according to ECE R141 - TPMS tire pressure sensors installed in all wheels including spare wheels Surface Treatment: - Complete steel construction blasted automatically with a shot blast machine after welding - Second shot blasting with corundum for optimal coating adhesion - HRM metallization of the entire vehicle chassis with ZINACOR 850 (85% zinc / 15% aluminum) to ensure best corrosion protection - Final painting with 2 coats of 2K topcoat, single color in MB 7350 Novagrau Accessories Included: - Removable steel front wall, approx. 400 mm high - 3kW electro-hydraulic unit for controlling hydraulic operations, except for hydraulic winches - 1 spare wheel - Outer beam on gooseneck with mounting holes for bolted lashing rings - First hole approx. 200 mm from the front, then approx. every 400 mm - 2 pairs of screw-in lashing rings included - 1 pair of lying lashing rings at the rear of the gooseneck - 1 pair of removable ALU side walls on the gooseneck, approx. 400 mm high, anodized - 1 removable ALU rear wall on the gooseneck, approx. 400 mm high, anodized - Approx. 40 mm thick hardwood floor over the gooseneck, tread plate covering over the king pin - 2" king pin - Round NATO socket on the front connector strip - 4 wheel chocks - 1 intermediate table, approx. 300 mm wide - 1 pair of lashing rings on the front crossmember - 8 pairs of recessed lashing rings in the outer frame of the loading area, foldable outwards - Extensions (galvanized) extendable by approx. 230 mm per side - Wheel recesses with square climbing strips, 15 x 15 mm in front of the axles, continuously open up to the gooseneck crossmember, approx. 700 x 410 mm - Wheel recesses with square climbing strips, 15 x 15 mm between the first and second axles, approx. 1,480 x 700 x 410 mm - ALU covers for the wheel recesses, which can also be used as bridging elements for the extension or as extension beams - 1 pair of mechanical rear supports - Radio and cable remote control - Lift axle at the front axle - Square climbing strips 20 x 30 mm, approx. every 200 mm - Central lubrication system with 1 pump - Wabco Smart Board System - 4 warning signs, approx. 423 x 423 mm, extendable by approx. 400 mm

Condition: new, empty load weight: 22,700 kg, maximum load weight: 79,300 kg, overall weight: 102,000 kg, axle configuration: > 3 axles, loading space length: 11,000 mm, loading space width: 2,850 mm, loading space height: 920 mm, tire size: 245/70 R 17.5, color: grey, operation weight: 22,700 kg, Equipment: ABS, Gooseneck: -Gooseneck in SNT design to optimize the loading platform length, length approx. 3,750 mm, with a rear slope of approx. 850 mm x 10° -Hydraulically extendable and retractable, stroke +- 250 mm incl. hydraulic connection connected to the hydraulic axle compensation of the first two axles -Open in the rear third -For semi-trailer tractors: 6 x 4 and 8 x 4 Loading platform: -Loading platform in extendable design, length approx. 11,000 mm with a slope at the rear of approx. 500 mm x 10°. -A recess in the loading platform and into the slope to accommodate the excavator arm, approx. 4,240 x 900 x 440 mm -Pneumatic locking with tapered locking pin and reinforced locking positions, the supply lines are protected in the extendable beams and automatically adapt to the respective loading platform length Ramps: -A pair of two-part steel ramps with a length of approx. 4,650 mm and a width of approx. 900 mm -Hydraulically folding ramp tips. -Ramps can be individually hydraulically shifted outwards by approx. 235 mm and inwards by approx. 215 mm -Rubber flooring "Super Grip" 25 mm and sheet metal flooring approx. 5 mm as additional reinforcement on the slope of the loading platform -Square climbing strips 20x30 mm, approx. every 200 mm on the outer frame of the ramp Axles, suspension and tires: Gkodpfxsk Af Svo Apqea -PA-X axle system, all axles hydro-mechanically forced steering -The steering behavior of the two front axles can be optimally adjusted both mechanically and hydraulically to the loading platform length. -Hose rupture valve on the axle compensation cylinders with automatic RESET function. -Hydraulic cylinders with shut-off valves and quick-release couplings to secure in the raised position. -245/70 R 17.5 3PMSF Included accessories: -Steel headboard, pluggable, approx. 400 mm high -Connection strip for supply lines to the semi-trailer tractor, mounted at the height of the outer frame profile -1 spare wheel -Outer carrier of the gooseneck with mounting holes for screwable lashing rings -The first hole approx. 200 mm from the front, then approx. every 400 mm -2 pairs of screw-in lashing rings included -Diamond plate flooring above the gooseneck -On the gooseneck, 1 pair of pluggable aluminum sideboards, approx. 400 mm high, anodized -On the gooseneck, a pluggable aluminum rear panel, approx. 400 mm high, anodized -3.5" kingpin / 2" kingpin mounted -Guide plate of the gooseneck for the turntable, approx. 500 mm wide -4 wheel chocks -4 axle load manometers -Mechanical outrigger supports at the front -1 INOX toolbox, one-piece, approx. 2,480 x 340 x 390 mm -Mechanical outrigger supports at the front -Continuous sheet metal flooring on the loading platform with a sand coating as an anti-slip measure -1 intermediate table, approx. 500 mm wide, for the extension, with elongated holes for attaching and adjustable bridging elements -Sand coating on the support surfaces of the intermediate table -Mechanical locking to lock the intermediate table to the extension -8 pairs of pocket rails in the outer frame -Extensions (galvanized), extendable by approx. 230 mm on each side -1 pair of hydraulic rear supports -Central lubrication system -1 reversing light on the left and right at the rear of the vehicle -3 kW electric-hydraulic unit -Extension planks, loose, in reinforced steel U-profile -Wireless and cable remote control -4 warning signs, approx. 423 x 423 mm

Condition: new, empty load weight: 12,800 kg, maximum load weight: 36,200 kg, overall weight: 49,000 kg, axle configuration: 2 axles, loading space length: 6,850 mm, loading space width: 2,550 mm, loading space height: 375 mm, tire size: 245/70 R 17.5, color: grey, operation weight: 12,800 kg, Equipment: ABS, Gooseneck: - Gooseneck in SNT design to optimize the loading area length, length approx. 3,750 mm - Gooseneck hydraulically raised/lowered and removable - Technical fifth wheel load: 25,000 kg - For tractor units: 4 x 2, 6 x 2, and 6 x 4 Loading area: - Low bed with external supports, designed as a telescopic tank bridge in a low construction with a front extension - Length 6,850 mm x Width 2,540 mm - One locking point approximately every 1,000 mm on the extension Rear chassis: - Rear chassis with closed outer frame with checker plate cover and continuous prism excavator trough approx. 1,250/700 x 505 mm, open at the rear Axles, suspension, and tires: - "PENDEL-AXLE", all Hydro-mechanically forced-steered axles - Hose rupture valve on the axle balancing cylinder with automatic reset function - Hydraulic cylinder with shut-off valves and pins for securing in the raised position - Final axle painting with two coats of 2-component acrylic paint in a single color "FAY-Gray-34-0260" - Technical axle load: 12,000 kg - Hydraulic axle balancing - Tires: 245/70 R 17.5 - TPMS tire pressure monitoring system in accordance with ECE R 14 - TPMS tire pressure monitoring sensors installed in all wheels, including spare tires Accessories included: - Steel bulkhead, plug-in, approx. 400 mm high - 3 kW electro-hydraulic unit for controlling the hydraulic processes, with the exception of hydraulic cable winches - One spare tire with mounting adapter - Gooseneck outer support with mounting holes for screwable lashing rings Gkodpfxsvy Edco Apqea -Slidable aluminum side walls on the gooseneck, approx. 400 mm high, anodized -Slidable aluminum rear wall on the gooseneck, approx. 400 mm high, anodized -Checker plate covering above the gooseneck -Gooseneck guide plate for the fifth wheel plate, approx. 500 mm wide -Illuminated control panel on the gooseneck with on/off switch -Hydraulic crossbar for supporting the gooseneck on the tractor unit or a dolly -2" kingpin -Anti-slip sticker on the left slope of the gooseneck -Gooseneck closed at the rear upper area with a removable cover -4 chocks with brackets -Hydraulic connections from the gooseneck to the drop bed with multi-coupling instead of screw couplings -1 pair of steel ramps with climbing rails and fastening bolts for bridging the drop bed's hooks -The Ramps can be installed over or between the hooks. -Attachment option for the steel loading ramps at the rear between the outer supports of the gooseneck. -Prepared for screw-on container holders for 1x20f on the outer support. -Mechanical bolt-and-lug coupling from the low bed to the chassis, for replacing the loading area or installing extension supports. -With electro-pneumatic-hydraulic couplings. -The outer supports of the low bed are provided with a painted layer of sand as a slip protection. -Removable loading floor (galvanized) in 3 elements, insertable between the outer supports with hardwood flooring. -Foldable extensions, by approximately 230 mm per side. -Hanging rail at the front of the rear chassis to the low bed for loose loading ramps. -2 pairs of stake pockets recessed into the outer frame of the chassis, for plug-in stakes approx. 100 x 50 mm. -Hanging rail for loose Aluminum docking ramps on the vehicle's end crossbar -Central lubrication system with 2 pumps -Wireless and cable remote control -4 warning signs, approximately 423 mm x 423 mm extendable -Extensive lashing positions

Condition: new, empty load weight: 15,900 kg, maximum load weight: 63,500 kg, overall weight: 68,000 kg, axle configuration: > 3 axles, loading space length: 12,700 mm, loading space width: 2,740 mm, loading space height: 860 mm, suspension: air, tire size: 235/75/r17,5, color: grey, operation weight: 52,100 kg, Equipment: ABS, Gooseneck: Gooseneck in SNT design to optimize the loading area length, length approx. 3,300 mm, rear with bevel approx. 1,000 mm x 10° Technical fifth-wheel load: 23,000 kg For SZM: 6x2, 6x4 and 8x4 Cargo bed: Loading area in extendable design, length approx. 9,400 mm with bevel at the rear approx. 500 mm x 10° A recess in the loading area and protruding into the chamfer to accommodate the excavator dipper stick approx. 3,850 x 950 x 210/290 mm Pneumatic locking with conical locking bolt and reinforced locking positions, the supply lines are protected in the extendable beams and automatically adjust to the respective loading area length Axles and tires: BPW axles and suspension, 1st axle rigid, all other axles hydro-mechanically forced steered Technical axle load: 12,000 kg Air suspension with lifting and lowering valve Axle tool 235/75 R 17.5 3PMSF dual tires Load index 143/141J (144/144F) Two-piece steel ramps: A pair of two-piece steel ramps with a length of approx. 4,350 mm and a width of approx. 900 mm Hardwood decking Hydraulically hinged ramp tips Ramps can be moved individually hydraulically by approx. 235 mm outwards and approx. 215 mm inwards Brake system: WABCO EBS-E brake system in accordance with EU regulations Sockets and lighting: 24-volt lighting system Full metallization: Complete HRM metallization with ZINACOR 850 to ensure the best corrosion protection Surface treatment: Complete steel structure automatically blasted after welding with wheel blast cleaning Second blasting with corundum for optimum adhesion of the coating system Final coating with 2 layers of 2-component paint in a single color in nova grey, followed by sealing of the cavities with special wax Rims in silver gray Steel construction: Steel construction made from high-strength fine-grain steels Steel grades: S355J2+N/S355MC S690QL/S700MC Gjdpfjmfqi Iox Apqeka Accessories: Steel end wall, pluggable, approx. 400 mm high Connection strip for supply lines to the SZM Spiral cable for supplying the electro-hydraulic unit and/or the electric cable winch between the trailer and SZM with plug Electro-hydraulic unit for controlling the hydraulic processes, with the exception of hydraulic cable winches Outer beam of the gooseneck with fastening holes for screwable lashing rings The first hole approx. 200 mm from the front, then approx. every 400 mm One fastening hole in the rear upper area of the gooseneck outer beam for a screwable lashing ring Approx. 40 mm thick hardwood covering over the gooseneck, checker plate covering over the kingpin Guide plate from the gooseneck for the fifth wheel plate, approx. 500 mm wide Continuous, approx. 50 mm thick hardwood planking on the loading area, interrupted between the axles Locking of the cargo bed with conically welded locking profiles every 250 mm, including pretensioning plate Slotted holes for attachable and movable bridging elements: on the fixed part behind the gooseneck on the front of the cargo bed 1 movable intermediate table, for the large cross-section extension tube Control valves for the hydraulic ramps on the right-hand side of the vehicle Central lubrication system with 1 pump, with standard grease according to NLGI-2 Radio remote control for operating the steering, in addition to the cable remote control, with 2 indicator lights on the receiver as single-track control

Condition: new, empty load weight: 10,000 kg, maximum load weight: 41,600 kg, overall weight: 51,600 kg, axle configuration: 3 axles, loading space length: 13,600 mm, loading space width: 2,540 mm, suspension: air, tire size: 235/75 R 17,5, color: grey, Equipment: ABS, Load area: - Gooseneck, length approx. 4,100 mm with central beam - Extendable load area, length approx. 9,500 mm with a slope at the rear of approx. 350 mm x 10° and integrated mounting rail for attaching loose aluminum approach ramps - Pneumatic locking with tapered locking bolts and reinforced locking positions - The supply lines are protected in the extendable beams and automatically adjust to the respective load area length Axles, suspension, and tires: - BPW axles and suspension, all axles hydro-mechanically forced steering - Mounted on a turntable - Technical axle load: 12,000 kg - Air suspension with lifting and lowering valve - Tires 235/75 R17.5, dual tires Painting: - 6-layer finish - Complete steel construction blasted after welding - One layer of zinc-based primer, one layer of adhesion primer - Final coat with 2 layers of 2-component paint (acrylic), solid color in MB 7350 Novagrau, followed by sealing of cavities with special wax Steel structure: - Steel structure made of high-strength fine-grained steels - Steel grades: - S355J2+N/S355MC (yield strength 355MPa) - S690QL/S700MC (yield strength 690MPa) - Welders certified according to DIN-EN 287-1 - Welding process MAG according to EN ISO 4063, shielding gas M21 according to EN ISO 14175 Accessories: - Front panel made of steel, approx. 1,600 mm high - Round NATO socket on the connection strip at the front - 3 kW electric-hydraulic unit for controlling the hydraulic operations - 4 pairs of recessed lashing rings in the outer frame of the gooseneck - 4 pairs of stake pockets recessed in the outer frame of the gooseneck, for stakes approx. 100x50 mm - 1 stake pocket strip mounted transversely in the load bed of the gooseneck, for stakes approx. 100x50 mm (1x at the rear of the gooseneck) - 2” kingpin - Mechanical landing gear with 2-speed gearbox and crank - JOST Module B – static test load = 50,000 kg - On the gooseneck and load area, approx. 32 mm wooden floor edged with aluminum omega profiles - A locking point on the extension, approx. every 500 mm - 10 pairs of recessed lashing rings lying in the outer frame of the load area, can be folded outwards - 6 pairs of stake pockets recessed in the outer frame of the load area, for stakes approx. 100x50 mm Gedpoiuy Nljfx Apqjka - 2 stake pocket strips mounted transversely in the load bed of the load area, for stakes approx. 100x50 mm - Tool box INOX approx. 1,250 x 500 x 550 mm - Slope on the end crossbar of the vehicle, approx. 350 mm 10° - Integrated mounting rail for loose aluminum approach ramps on the end crossbar of the vehicle - 1 pair of outrigger supports at the end crossbar - Fenders on all axles - Central lubrication system with 1 pump - Steering from the front and rear via cable remote control, operable via push buttons, with single-axle control - Under the gooseneck and at the rear on the end crossbar, one 7-pole socket each for warning signs - One 7-pole socket on the end crossbar - Container locks “TWIST-LOCKS” in the load area for the transport of 2x 20ft and 1x 40ft containers - Radio remote control for the steering, in addition to the cable remote control, with 2 indicator lights on the receiver for single-axle control - 2 axle load gauges + axle load diagram - 4 warning signs approx. 423 x 423 mm, extendable by approx. 400 mm - Standard HRM metallization (High Resistance Metallization) of the outer frame - Complete steel construction blasted, then the defined visible surfaces hot-dip galvanized with ZINACOR 850 (zinc 85% - alu

Condition: used, machine/vehicle number: YAFTL410000011078, axle configuration: > 3 axles, first registration: 01/2010, total length: 18,200 mm, total width: 2,750 mm, total height: 2,550 mm, suspension: air, color: other, Year of construction: 2010, Special Transport Length above axes: 560 cm Length of loading floor: 750 cm Length of swan neck: 500 cm Lowloader: ✓ Max width: 313 cm Expandable: ✓ Gkedjwid Dlopfx Apqoa Extendable: ✓ = More information = Make axles: Saf Brakes: drum brakes Suspension: air suspension Front axle: Double wheels; Steering; Tyre profile left outer: 80%; Tyre profile right outer: 75% Middle axle 1: Double wheels; Steering; Tyre profile left outer: 80%; Tyre profile right outer: 75% Middle axle 2: Double wheels; Steering; Tyre profile left outer: 90%; Tyre profile right outer: 90% Rear axle: Double wheels; Steering; Tyre profile left outer: 90%; Tyre profile right outer: 90% GVW: 80.000 kg Registration number: Y0101796 = Dealer information = For more information on this unit please call: or e-mail: . A full stock overview can be found at: . Please do not forget to subscribe to our newsletter for weekly updates on our stock.

Condition: used, machine/vehicle number: YAFTL413000014309, axle configuration: > 3 axles, first registration: 01/2013, total length: 18,600 mm, total width: 2,750 mm, total height: 3,250 mm, suspension: hydraulics, tire size: 285/70 R19.5, color: other, Year of construction: 2013, = Additional options and accessories = - Drum brakes - Steering Axle = Remarks = Chassis Diameter coupling pin / coupling plate: 2 inch Drum brake: ✓ Gkjdsxtp Rvepfx Apqsa Structure Construction year: 2013 Special Transport Detachable swan neck: ✓ Length above axes: 540 cm Length of loading floor: 665 cm Lowloader: ✓ Max width: 3 cm (275 cm ) Expandable: ✓ NON-EU VEHICLE, REQUIRES CUSTOMS CLEARANCE // 4-axle lowloader with forced steering, Max weight 88.000 kg, Removable neck, Load bed lenght 665 cm, Load bed width 275 cm, Max load bed widht 3 cm (275 cm), Load bed height 65 cm, Axle plateau lenght 540 cm, Axle plateau height 105 cm, Saf axles, Hydraulic suspension, ABS, Forced steering, 4 steering axles, Drum brakes, Tires 285/70R19.5, Shipment dimensions 1860x275x3 cm = More information = Tyre size: 285/70 R19.5 Make axles: Saf Brakes: drum brakes Suspension: hydraulic suspension Front axle: Double wheels; Steering; Tyre profile left outer: 50%; Tyre profile right outer: 65% Middle axle 1: Double wheels; Steering; Tyre profile left inner: 15%; Tyre profile right outer: 15% Middle axle 2: Double wheels; Steering; Tyre profile left outer: 20%; Tyre profile right outer: % Rear axle: Double wheels; Steering; Tyre profile left inner: 45%; Tyre profile right outer: % Make of bodywork: Faymonville STBZ-4VA = Dealer information = For more information on this unit please call: or e-mail: . A full stock overview can be found at: . Please do not forget to subscribe to our newsletter for weekly updates on our stock.

Condition: used, machine/vehicle number: YAMT14XX5K0104637, axle configuration: > 3 axles, first registration: 01/2020, total length: 14,100 mm, total width: 2,550 mm, total height: 3,350 mm, suspension: air, tire size: 235/75 R17.5, color: other, Year of construction: 2020, Chassis Chassis height: 90 cm Diameter coupling pin / coupling plate: 2 inch Structure Dish height: 120 cm Special Transport 2-piece driving plates: ✓ Hydraulic ramps: ✓ Length above axes: 90 cm Length of loading floor: 930 cm Length of ramps: 405 cm Length of swan neck: 430 cm Max width: 305 cm (20 cm + 20 cm) Max. length: 930 cm Expandable: ✓ Tank Fuel: ✓ 3-axle semi lowbed trailer with hydraulic ramps, ABS, Air suspension, 1st axle lifting axle, 3rd and 4th axles passive steering axles, Drum brakes, Saf axles, Tyres 235/75R17.5, Double tyres, Kingpin diameter 2 inch // DIMENSIONS // 60800 kg max weight, Load bed lenght 930 cm, Load bed width 255 cm, Max load bed width 305 cm, Load bed height 90 cm, Gooseneck lenght 430 cm, Gooseneck height 160 cm, Kingping height 120 cm, Ramp lenght 405 cm, Shipment dimensions: 1410x255x335 cm = More information = Axle configuration Tyre size: 235/75 R17.5 Make axles: Saf Brakes: drum brakes Suspension: air suspension Gkodpfx Apsu H D Tajqea Axle 1: Double wheels; Lift axle; Tyre profile left outer: 15%; Tyre profile right outer: 80% Axle 2: Double wheels; Tyre profile left outer: 60%; Tyre profile right outer: 50% Axle 3: Double wheels; Steering; Tyre profile left outer: 70%; Tyre profile right outer: 70% Axle 4: Double wheels; Steering; Tyre profile left outer: 75%; Tyre profile right outer: 65% Weights Empty weight: 11.480 kg Carrying capacity: 49.320 kg GVW: 60.800 kg Functional Make of bodywork: Faymonville Height of cargo floor: 90 cm Identification Registration number: C525073 = Dealer information = For more information on this unit please call: or e-mail: . A full stock overview can be found at: . Please do not forget to subscribe to our newsletter for weekly updates on our stock.

Condition: used, machine/vehicle number: YAFTL408100008968, axle configuration: > 3 axles, first registration: 01/2008, total length: 13,400 mm, total width: 2,750 mm, total height: 3,400 mm, suspension: air, tire size: 245/70 R17.5, color: other, Year of construction: 2008, = Additional options and accessories = Gsdjxhgirepfx Apqska - Drum brakes - Steering Axle = Remarks = Chassis Diameter coupling pin / coupling plate: 2 inch Height of coupling pin / drawbar: 120 cm Drum brake: ✓ Structure Construction year: 2008 Faymonville extendable 4-axle semi-lowbed trailer type STN 4AU, Gross weight 65000 kg, Load bed lenght 910 cm, Max load bed lenght when extended..... cm, Max load bed width 3 cm (275 cm), Load bed height 90 cm, Hydraulic ramps, Ramp width 85 cm, Air suspension, 2 passive steering axles, Gigant axles, Drum brakes, ABS, Tire size 245/70R17.5, Double tires, Shipment dimensions 1340x275x340 cm = More information = Axle configuration Make axles: Gigant Brakes: drum brakes Suspension: air suspension Front axle: Tyre size: 245/70 R17.5; Tyre profile left: 60%; Tyre profile right: 35% Middle axle: Tyre size: 245/70 R22.5; Tyre profile left: %; Tyre profile right: 50% Rear axle 1: Tyre size: 245/70 R17.5; Steering; Tyre profile left: 45%; Tyre profile right: 20% Rear axle 2: Tyre size: 245/70 R17.5; Steering; Tyre profile left: 50%; Tyre profile right: 60% Weights Empty weight: 17.500 kg Carrying capacity: 47.500 kg GVW: 65.000 kg Functional Make of bodywork: Faymonville = Dealer information = For more information on this unit please call: or e-mail: . A full stock overview can be found at: . Please do not forget to subscribe to our newsletter for weekly updates on our stock.

Condition: used, machine/vehicle number: ***YAMT13XX6K0104043, axle configuration: 3 axles, first registration: 01/2019, total length: 13,800 mm, total width: 2,550 mm, total height: 3,410 mm, suspension: air, tire size: 235/75 R17.5, color: other, Year of construction: 2019, Chassis Chassis height: 87 cm Diameter coupling pin / coupling plate: 2 inch Height of coupling pin / drawbar: 120 cm Special Transport 2-piece driving plates: ✓ Hydraulic ramps: ✓ Length of loading floor: 930 cm Length of ramps: 395 cm Length of swan neck: 415 cm Lowbed trailer: ✓ Max width: 300 cm (25 cm per side) Max. length: 1380 cm Expandable: ✓ Tank Fuel: ✓ NON-EU VEHICLE, REQUIRES CUSTOMS CLEARANCE // 3-axle semi-lowbed trailer with hydraulic ramps, Max design weights 49500 kg, ABS, Air suspension, Drum brakes, SAF axles, Tyres 235/75R17.5, 3rd axle steering axle. // Dimensions // Load bed lenght 930 cm, Load bed width 250 cm, Load bed height 87 cm, Gooseneck lenght 415 cm, Gooseneck floor height 148 cm, Kingpin height 120 cm, Kingpin diameter 2 inches, Ramp lenght 395 cm, Ramp width 80 cm // Shipment dimensions 1380x255x341 cm = More information = Axle configuration Tyre size: 235/75 R17.5 Make axles: Saf Brakes: drum brakes Suspension: air suspension Axle 1: Double wheels; Tyre profile left outer: 60%; Tyre profile right outer: 60% Axle 2: Double wheels; Tyre profile left outer: 20%; Tyre profile right outer: 30% Axle 3: Double wheels; Steering; Tyre profile left outer: 55%; Tyre profile right outer: 50% Weights Empty weight: 10.040 kg Carrying capacity: 30.960 kg GVW: 41.000 kg Functional Make of bodywork: Faymonville Height of cargo floor: 87 cm Identification Registration number: C505325 = Dealer information = Gksdpou H D R Ejfx Apqja For more information on this unit please call: or e-mail: . A full stock overview can be found at: . Please do not forget to subscribe to our newsletter for weekly updates on our stock.

Condition: excellent (used), axle configuration: 3 axles, first registration: 07/2016, suspension: air, Year of construction: 2016, Equipment: tail-lift, Suspension: Air suspension Gedsvvwzrepfx Apqeka Rear axle 1: Steered Rear axle 2: Steered Rear axle 3: Steered Gross vehicle weight: 48,000 kg Technical condition: Very good Visual condition: Very good Price: On request Please contact David F Middelman for further information.

Condition: excellent (used), axle configuration: 2 axles, first registration: 09/2020, color: red, Year of construction: 2020, Equipment: ABS, Rear axle 1: Twin tires Rear axle 2: Twin tires; Steered Unladen weight: 8,060 kg Loading platform height: 86 cm Extendable body: Yes Technical condition: Very good Visual condition: Very good Price: On request FAYMONVILLE F-S42-111A SEMI LOWLOADER 2x SAF axles 1x steering axle (trailing) Tire size Extendable loading platform Size: 680 cm + 420 cm extendable / Total platform length: 1,100 cm Platform width: 254 cm Platform height: approx. 86 cm Gooseneck length: 330 cm Lashing eyes, stanchion sockets, twistlocks Follow us on Instagram: GEURTSTRUCKS Lowloader is year 2016 but sold new in 2020 Gsdpfex Upxxex Apqska We speak German Hablamos Español We speak English

Condition: new, overall weight: 49,500 kg, axle configuration: 3 axles, loading space length: 9,700 mm, loading space width: 2,540 mm, loading space height: 890 mm, suspension: air, tire size: 235/75 R 17.5, color: grey, Equipment: ABS, Gooseneck: - Gooseneck in SNT design to optimize the loading deck length, approx. 3,700 mm long, rear end with chamfer approx. 1,000 mm x 6° - For tractor units: 4 x 2 and 6 x 2 Loading Deck: - Loading deck, approx. 9,700 mm long with hydraulically folding and lowering rear section, plus hydraulically liftable front section for driving onto the gooseneck Axles and Tyres: - BPW axles and suspension, 1st and 2nd axles fixed, 3rd axle self-steering - 3rd axle with electro-magnetic reverse lock, activated via reverse gear and manual switch - Technical axle load: 12,000 kg - Air suspension with lift and lower valve - 235/75 R 17.5 3PMSF, twin tyres - TPMS tyre pressure monitoring system according to ECE R 141 BPW Auto Reverse Control: - Electrohydraulic auxiliary steering for self-steering axle of 3-axle assembly - Automatic control of the self-steering axle when reversing using a gyroscope sensor - Manual control for steering in forwards and reverse, via separate radio remote control Gkjdpfxsyw Sakj Apqsa - Manual operation enabled up to 10 km/h - System supplied via a separate electro-hydraulic unit Included Accessories: - Removable steel front wall, approx. 400 mm high - 3 kW electro-hydraulic power unit - Outer beams on the gooseneck with mounting holes for bolted lashing rings - First hole approx. 200 mm from the front, then every 400 mm - One mounting hole in the upper rear area of the outer beams for a bolted lashing ring - On the gooseneck and rear chamfer: grating floor with 5 mm steel reinforcement - 2" kingpin - Guide plate on the gooseneck for the fifth wheel, approx. 500 mm wide - Round NATO socket on the front interface (Maeler & Kaege VG 96 917) - On the gooseneck: 1 pair of removable ALU sidewalls, approx. 400 mm high, anodized - 4 wheel chocks - Electric cable winch, approx. 5,400 kg pulling force, with radio remote control - Wire rope approx. 24 m long, rope ø approx. 9.5 mm, incl. rope press roller - Winch mounted front inside the gooseneck - Continuous grating floor with 5 mm steel plate reinforcement for additional strength, designed for point load: - on the lift bed - on the loading deck - on the hydraulically lowerable rear section - Painted sand coating on the gooseneck cover plates and in the transition areas between neck and lift bed, lift bed and loading deck, and loading deck and ramps - 1 spare wheel - Hydraulic lift bed, approx. 2,500 mm long, load capacity in raised position while driving: 9,000 kg - Hydraulic cylinders equipped with load-holding valves - Cut-outs in the outer frame of the loading deck and lift bed for inserting tensioning straps - Extensive lashing points - Hydraulic rear section lowerable for loading/unloading and liftable for reducing overall length - Load capacity when horizontal while driving: 10,000 kg - Reduction of overall length when raised: 2,350 mm - Painted sand coating on the complete ramp except extendable galvanized part - Hydraulically extendable rear extensions for loading/unloading - Radio remote control: - Operation of the hydraulic lift bed - Operation of the hydraulic lift of the rear extension - Operation of the hydraulic extension of the rear extension - 1st axle with starting aid - Central lubrication system with 1 pump - 4 extendable warning panels, approx. 423 x 423 mm

Condition: new, overall weight: 49,500 kg, axle configuration: 3 axles, loading space length: 9,700 mm, loading space width: 2,540 mm, loading space height: 890 mm, suspension: air, tire size: 235/75 R 17.5, color: grey, Equipment: ABS, Gooseneck: - Gooseneck in SNT design for optimizing the loading platform length, approximately 3,700 mm long, with a rear chamfer approximately 1,000 mm x 6° - For tractor units: 4 x 2 and 6 x 2 Loading Platform: - Loading platform, approximately 9,700 mm long, with hydraulically folding and tilting rear, including a hydraulically liftable front section for access onto the gooseneck Axles and Tyres: - BPW axles and suspension, 1st and 2nd axles fixed, 3rd axle steered - 3rd axle with electro-magnetic reversing lock, activated via reverse gear and manually - Technical axle load: 12,000 kg - Air suspension with lift and lower valve - 235/75 R 17.5 3PMSF twin tyres - TPMS tyre pressure monitoring system according to ECE R 141 Gkedoyw R Srspfx Apqea Included Accessories: - Removable steel front wall, approx. 400 mm high - Yellow-red air couplings on the front connection panel - 3 kW electro-hydraulic unit for hydraulic operations, except for hydraulic winches - External gooseneck beams with mounting holes for bolted lashing rings - First hole approx. 200 mm from the front, then every approx. 400 mm - 2 pairs of screw-in lashing rings included - One mounting hole in the rear upper area of the external gooseneck beams for a bolted lashing ring - Grating surface with 5 mm steel reinforcement on the gooseneck and rear chamfer - 2" kingpin - Gooseneck guide plate for fifth wheel, approx. 500 mm wide - Round NATO socket on front connection panel (Maeler & Kaege VG 96 917) - 1 pair of removable ALU side boards, approx. 400 mm high, anodized, mounted on the gooseneck - 4 wheel chocks - Electric winch, approx. 5,400 kg pulling force, with radio remote control - Steel cable approx. 24 m long, cable diameter approx. 9.5 mm, including cable pressure roller - Winch installed at the front inside the gooseneck - Plastic cover for the winch - Mechanical landing legs with 2-speed gearbox and crank - JOST Modul B – static test load = 50,000 kg - Continuous grating surface with 5 mm steel backing as additional reinforcement, designed for point loads: - on the lift bed - on the loading platform - on the hydraulically lowerable rear section - Painted sand coating on the cover plates of the gooseneck, as well as in transition areas between neck and lift bed, lift bed and loading platform, and loading platform and ramps - 1 spare wheel with mounting adapter under the loading platform, right side in front of the axles - Hydraulic lift bed, approximately 2,500 mm long, load capacity while driving in raised position: 9,000 kg - Hydraulic cylinders fitted with load-holding valves - Cut-outs in the outer frame of the loading platform and lift bed for attaching lash straps - Extensive lashing positions - Hydraulic rear section lowerable for loading and unloading and raisable for shortening overall train length - Load capacity while driving in horizontal position: 10,000 kg - Reduction of overall train length in raised position: 2,350 mm - Painted sand coating on the entire ramp, except the extendable galvanized part of the ramp - Hydraulically extendable rear extension for loading and unloading Radio Remote Control: - Operation of the hyd. lift bed - Operation of the hyd. lifting mechanism for the rear extension - Operation of the hyd. sliding function of the rear extension - 1st axle with traction aid - Central lubrication system with 1 pump - 4 warning signs, approx. 423 x 423 mm, extendable