Used Faymonville Lowbed Semitrailers for sale (185)

Condition: new, maximum load weight: 42,900 kg, overall weight: 55,000 kg, axle configuration: 3 axles, loading space length: 29,000 mm, total width: 2,540 mm, Equipment: ABS, You will find our complete vehicle inventory, including vehicles available immediately and at short notice, on our website. Excerpt from the equipment list. Full specification available on request. LOADING PLATFORM: * Gooseneck, length approx. 3,900 mm with central beam * Loading platform with double-extension, length approx. 9,300 mm * A support table approx. 200 mm wide is permanently welded to the central beam * Pneumatic locking with conical locking pin and reinforced locking positions; supply lines are protected inside the extendable beams and automatically adjust to the respective loading platform length (except for the supply to the first and second lock) * Technical fifth wheel load: 25,000 kg for tractor units: 4x2, 6x2 and 6x4 * TPMS tire pressure monitoring system according to ECE R 141 * BPW axles and suspension, all axles forced steered hydro-mechanically, mounted on turntables * Technical axle load: 12,000 kg each. Air suspension with lifting and lowering valve * 275/70 R 22.5 3PMSF twin tyres. Brand of our choice * ASPÖCK-UNIBOX at the front connection bar with 24N, 24S & 15-pin sockets * 3 kW electro-hydraulic unit for hydraulic operations * 3 pairs of recessed lashing rings in the outer frame of the gooseneck, foldable outward * At the king pin 1 pair of lashing rings (LC 10,000 daN) – all other lashing rings (LC 5,000 daN) * 3 pairs of stake pockets integrated in the outer frame of the gooseneck, for plug-in stakes approx. 100 x 50 mm * 1 crosswise stake pocket bar mounted in the floor of the gooseneck, for plug-in stakes approx. 100 x 50 mm * 1 at the rear of the gooseneck * 2" king pin Kjdpfxjyvnd Ne Abnsdp * Mechanical landing gear with 2-speed gearbox and crank * 8 pairs of stake pockets integrated in the outer frame of the loading platform, for plug-in stakes approx. 100 x 50 mm * 10 pairs of recessed lashing rings lying in the outer frame of the loading platform, foldable outward * Rear and front steering operable via cable remote control, with single-track axle control, no installation in the tractor unit required * Last axle with air suspension venting activated when the parking brake is applied * Steel front wall, approx. 1,600 mm high, certified according to EN 12642: 2016 XL * Round NATO socket at the front connection bar (Maeler & Kaege VG 96 917) * 1 LED work light each left and right at the landing gear, wired to the tractor unit connection * Wooden floor approx. 32 mm thick on the gooseneck and loading platform * At the extension tube with large cross-section, one locking position every approx. 500 mm * At the extension tube with small cross-section, one locking position every approx. 1,000 mm, allowing for locking every approx. 500 mm * Cut-outs in the outer frame of the loading platform for hooking lashing straps (LC 2,500 daN) * 4 crosswise stake pocket bars mounted in the loading platform floor, for plug-in stakes approx. 100 x 50 mm * 4 wheel chocks with holder under the loading platform * 1 lockable INOX toolbox, approx. 2,390 x 800 x 500 mm (L x W x H), mounted under the loading platform on the left in direction of travel * 1 additional lockable INOX toolbox, approx. 1,250 x 500 x 550 mm (L x W x H), mounted under the loading platform on the right in direction of travel * 1 LED work light each left and right in front of the axles, with wiring * 2 axle load gauges mounted on the left side including axle load diagram * 1st axle with automatic lift axle function as well as starting...

Condition: new, maximum load weight: 96,500 kg, overall weight: 126,000 kg, axle configuration: > 3 axles, loading space length: 26,900 mm, total width: 2,750 mm, Equipment: ABS, You can find our complete vehicle inventory, including vehicles available for immediate and short-term delivery, on our website. Excerpt from the equipment list. Complete equipment list available upon request. Gooseneck: * Hydraulically extendable/retractable and lowerable gooseneck. Length approx. 3,650 mm * For semi-trailer with multiple axles (SZMs): 6 x 4 or 8 x 4 * Truck hydraulic connection with flow control (20 l/min), incl. gantry for suspending the supply lines, the SZM tank must have a minimum capacity of 80 l * With MAX Trailer coupling parts, otherwise coupling parts must be supplied by the customer * Gantry with winch for spare wheel on the front of the gooseneck * 3.5-inch kingpin * Steel front panel approx. 400 mm high * Plug-in aluminum side and rear panels on the gooseneck, approx. 400 mm high, in anodized finish * Control levers on the gooseneck protected by a folding cover * Lighting for the controls on the gooseneck with on/off switch * A 7-pin socket on the left and right at the rear of the gooseneck for the warning sign * BEKA-MAX central lubrication system for a gooseneck with standard grease NLGI-2 * Hydraulic connections from the gooseneck to the low-bed with screw couplings * Access to the gooseneck * Four warning signs that can be extended by approx. 1,000 mm, approx. 423 x 423 mm, with an LED position light and a mounting bracket for a rotating beacon * Mounting adapter for 2 spare wheels * 1-cylinder Hatz diesel engine (Silent Pack) with electric starter and starter battery. Power: 9.5 kW (12.9 hp) at 3000 rpm * Hydraulic connection lines between the power pack and the connector plate on the gooseneck * 1 LED work light on the left and right at the rear of the gooseneck with separate on/off switch * Radio remote control: - Operation of the power pack, start/stop of the diesel engine. - Operation of the trailing axle steering, in addition to the cable remote control, with 2 LED indicator lights on the receiver as a single-axle control. - Operation of raising/lowering the gooseneck - Operation of raising/lowering the suspension of the chassis 2-axle front bogie: * Bolt-on coupling at the front and rear. Length: approx. 2,970 mm. Chassis width: approx. 2,750 mm * BEKA-MAX central lubrication system for a 2-axle chassis with standard grease NLGI-2. (not connected to the track rods) * A 7-pin socket on the left and right at the rear of the front bogie for the warning signs Kedpjzahp Sjfx Abnodp * Surface of the chassis with a sand-blasted coating for slip resistance * Yellow reflector tape according to EU regulations on the side, on the extension, and at the rear of the trailer * A 7-pin socket for the warning signs, on the left and right on the front chassis, in the area of the axles * Extendable widening elements by approx. 230 mm on each side for a 2-axle chassis * 1 pair of M42 threaded blocks between the axles of the front bogie * 1 pair of brackets for the warning signs for insertion into the pocket recesses in the outer frame of the loading platform Loading platform: * 6-axle double-extendable loading platform with bolt-on coupling at the front and a slope of approx. 500 mm x 8° at the rear * Loading platform length: approx. 11,000 mm * Technically extendable by: approx. 8,200 + 7,700 mm * Axle spacing: approx. 1,500 mm * Basic width: approx. 2,750 mm * Hydraulic coupling pin * BEKA-MAX central lubrication system for the loading platform with standard grease NLGI-2 * Surface of the loading platform with a sand-blasted coati

Condition: new, maximum load weight: 36,500 kg, overall weight: 48,000 kg, axle configuration: 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory, including vehicles available for immediate and short-term delivery, on our website. A selection of features is listed below. Complete equipment upon request. GOOSENECK: * Gooseneck in SNT design to optimize the bed length, approximately 3,700 mm long, with a rear bevel of approximately 1,000 mm x 6° * For SZM (tractor unit): 4 x 2 and 6 x 2 * ASPÖCK-UNIBOX * The gooseneck and the rear bevel have a grid flooring with a 5 mm sheet metal reinforcement * 2-inch King Pin * Guide plate on the gooseneck for the turntable, approximately 500 mm wide * Round NATO socket on the connection strip at the front (Maeler & Kaege VG 96 917) * On the gooseneck, one pair of plug-in aluminum sideboards, approximately 400 mm high, in an anodized finish * One LED work light each on the left and right at the top of the front wall, with operation via an on/off switch (operation of the work lights from the SZM is not possible in this case) LOADING AREA: * Loading area, approximately 9,600 mm long, with a rear bevel of approximately 900 mm x 6° * The loading area behind the gooseneck can be hydraulically raised and lowered, approximately 3,000 mm long, with a load capacity of up to approximately 9,000 kg * Continuous grid flooring on the lifting platform and loading area with approximately 5 mm sheet metal underneath as additional reinforcement, designed for point loads TIRES: * 235/75 R 17.5 3PMSF, twin tires. Brand of our choice * TPMS tire pressure monitoring system in accordance with ECE R 141 AXLES: * BPW axles and suspension, 1st and 2nd axles rigid, 3rd axle trailing * 3rd axle with electro-magnetic reversing lock, activated via reverse gear and manually * 1st axle with starting assist * Technical axle load: 12,000 kg each * Air suspension with lift and lower valve HYDRAULIC LOADING RAMPS: * One pair of two-part AXS steel ramps with grid flooring, approximately 4,920 mm long and approximately 900 mm wide * Hydraulically foldable ramp tips * Ramps can be hydraulically shifted outwards by approximately 235 mm and inwards by approximately 365 mm individually * Strobe lights on the outside of the ramp tips, with a switch next to the ramp operation control * Ramp locking in the driving position by means of a quick-release fastener * Painted sand coating on the outer frame of the ramp and on the ramp tip * Mechanical supports in downpipe design on the sides of the ramps to provide support when docking with loading ramps * Control valves for the hydraulic ramps on the right side of the vehicle BRAKE SYSTEM: Kodpfxsy Auhhj Abnsdp * Brake system from WABCO EBS-E, in accordance with EU regulations SURFACE TREATMENT: * HRM metallization of the entire vehicle chassis with ZINACOR 850 (85% zinc/15% aluminum) to ensure the best corrosion protection PAINTING: * Trailer: Carmine Red (RAL 3002) * Rims: Silver-grey * Sideboards: Aluminum, natural finish * Wheel hubs: According to axle manufacturer * Lamp panel: Pure white (RAL 9010) EQUIPMENT: * Front wall made of steel, plug-in, approximately 1,600 mm high, including connection strip for supply lines to the SZM, mounted approximately 1,000 mm from the bottom edge of the outer frame profile * Attachment option for lashing chains on the inside of the front wall on the left and right, including aluminum trough underneath on the left and right for storing chains or lashing straps * Approximately 12 mm thick DELIGNIT flooring screwed to the back of the front wall * Two pairs of screwable lashing

Condition: new, maximum load weight: 30,190 kg, overall weight: 43,000 kg, axle configuration: 2 axles, Equipment: ABS, You can find our complete vehicle inventory, including immediately and short-term available vehicles, on our website. Extract from the equipment list. Full equipment details available on request. Kdjdpfjxarl Njx Abnjp Loading Platform: - Lowbed with external beams in extendable SUPER LOW design, length approx. 6,850 mm - Lowbed with fixed hardwood floor approx. 40 mm thick and mechanical locking mechanism - Supply lines protected inside the extendable side rails, automatically adjusting to the current bed length - 5 pairs of lashing rings, foldable outward (LC 10,000 daN) - 6 pairs of threaded blocks on the inner beam for attaching RUD screw-on rings Gooseneck: - Gooseneck in SNT design for optimized platform length, length approx. 3,750 mm - Gooseneck hydraulically liftable/lowerable and detachable - Technical fifth wheel load: 23,000 kg - For tractors: 4x2, 6x2 Rear Chassis: - Rear chassis in short version with closed external frame and checker plate cover - Running gear with excavator recess, closed in the rear half to accommodate the air tanks - 2 pairs of lashing rings, foldable outward (LC 5,000 daN) - 1 pair of lashing rings, foldable outward (LC 10,000 daN) - 1 pair of lashing rings horizontal, front & rear of the chassis (LC 10,000 daN) Axles: - BPW axles, hydro-mechanically forced steering - Technical axle load per axle: 12,000 kg - Air suspension with lift and lower valve Tyres: - Tyres 245/70 R 17.5 3PMSF - Manufacturer of our choice - Load index (146/146F) - TPMS tyre pressure monitoring system in accordance with ECE R 141 - Data transmission to the truck via the standardized EBS interface in accordance with ISO 11992 - The truck must be capable of processing and displaying this data for correct operation Braking System: - Braking system according to EU regulations with EBS-E (2S2M) Electrical System: - Electrical system according to EU regulations, lighting 24 Volt ASPÖCK-NORDIK (ASS3) - All LED side marker lights flash with indicators - ASPÖCK-UNIBOX at the front connection point with 24N, 24S, and 15-pin sockets as per standards: - 24N ISO-1185 - 24S ISO-3731 - 15-pin ISO-12098 Steel Construction: - Steel construction from high-strength fine-grained steels - Steel grades: S355J2+N/S355MC (yield strength 355 MPa) S690QL/S700MC (yield strength 690 MPa) Paintwork: - Complete steel structure is automatically shot-blasted after welding using a blasting turbine system - Second blasting process with corundum for optimal adhesion of coating system - HRM metallization of complete chassis with ZINACOR 850 (85% zinc / 15% aluminum) to ensure maximum corrosion protection - Final paint finish with 2 coats of 2K topcoat, single color in RAL 3002 Carmine Red, as per RAL system 841GL - Rims in silver - Rear section metallized and painted RAL 9010 (Pure White) - Metallic paint not possible - Paint system tested in salt spray test as per ISO 9227-NSS - Cavities sealed with special wax Including the following additional equipment: - 2" King pin - One galvanized steel front wall, approx. 400 mm high - Remote steering of front and rear axles by cable remote control with pushbuttons, including single track axle monitoring (without installation in the tractor unit) - Hydraulic connections from gooseneck to lowbed with multi-coupling instead of screw couplings - Electro-hydraulic power pack - Preparation for mounting container locks for 1x 20' or 1x 40' container on the external beams - Without container locks

Condition: used, empty load weight: 14,995 kg, maximum load weight: 50,805 kg, overall weight: 65,800 kg, axle configuration: > 3 axles, first registration: 10/2023, loading space length: 9,300 mm, loading space width: 2,540 mm, loading space height: 900 mm, suspension: air, tire size: 235/75 R17.5, color: grey, Year of construction: 2023, operation weight: 14,995 kg, Equipment: ABS, You will receive a current and complete inspection and functional report for every used trailer. Gooseneck: -Gooseneck with rear bevel of approx. 750 mm x 10° -3 pairs of lashing rings (LC 5,000 daN) -Hardwood covering 30 mm thick Loading area: -Loading area in extendable version with rear bevel of approx. 500 mm x 8° -6 pairs of lashing rings that can be folded outwards (LC 5,000 daN) -4 pairs of lashing rings that can be folded outwards (LC 10,000 daN) -1 pair of lashing rings lying in the front of the loading area (LC 10,000 daN) -1 intermediate table 250 mm -Cutouts in the outer frame of the loading area for hanging tensioning straps (LC 2,000 daN) -Hardwood covering approx. 48 mm thick, checkered sheet covering above the axles Axles and Tires: -BPW axles with hydro-mechanical forced steering -Technical axle load: 12,000 kg -Air suspension with lifting and lowering valve -Axle tool -Tires 235/75 R17.5 Braking system: -Braking system in accordance with EU regulations with EBS-E (4S3M) Accessories included: -2" kingpins -A galvanized steel bulkhead approx. 400 mm high -Yellow-red air couplings on the galvanized connection strip at the front -4 brake shoes with holder on the bulkhead -A spare wheel with holder in front of the bulkhead -Electro-hydraulic unit -Steering from the front and rear can be operated using a cable remote control via push buttons, with alignment control of the axles -Mounting in the rear area of the gooseneck for aluminum docking ramps -Galvanized extensions, extendable by approx. 230 mm on each side -European reflector signs (red-yellow) on the rear of the trailer -White reflector tape in accordance with EU regulations on the side, on the extension and at the rear, red -On the gooseneck and on the rear panel, left and right, a bracket for the warning signs including a socket -Galvanized folding supports under the slope of the loading area -A bracket for a rotating beacon at the rear of the trailer -Central lubrication system with 2 BEKAMAX (Pico) pumps with normal grease NLGI-2 and removable protection around the pump -A mud flap at the rear of the trailer -Manual and description -ALU side walls and rear wall can be plugged into the gooseneck, approx. 2,440 x 400 mm -The rear galvanized plug-in stanchions are removable (length of the body approx. 2,560 mm) -4 pairs of WADER container pockets in the loading area for a 20ft, 2x 20ft, 40ft or a 45ft container -8 pairs of stake pockets for 100 x 50 mm stakes in the outer frame of the loading area -Movable mounting rails for aluminum ramps at the rear of the vehicle -Lift axle on the front axle with control by TEBS E depending on the current axle load and the current loading status -Four warning signs, approx. 423 x 423 mm, extendable by approx. 400 mm, with a position light -A holder for a rotating beacon on the warning signs -Radio remote control for the steering in addition to the cable remote control, with indicator lights on the receiver as a lane control -A painted layer of sand on the checker plates, above the kingpin and the loading area as a slip protection device -Speed sticker 80 km/h at the rear -Load pressure gauge for determining the axle loads including load diagram Kdedpfxsv Hr Axs Abnjp

Condition: new, maximum load weight: 36,040 kg, overall weight: 53,000 kg, axle configuration: 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory with vehicles available immediately and in the short term on our website. Excerpt from the equipment list. Complete equipment list available upon request. Gooseneck: Kdedpsy Uwu Ijfx Abnep * Gooseneck in SNT design to optimize the loading area length, length approx. 3,750 mm * Gooseneck hydraulically raisable/lowerable and extendable * For tractor unit: 6 x 4 or 8 x 4 Low-bed: * Low-bed with external beams in an extendable SUPER LOW design, length approx. 8,000 mm * Low-bed with a fixed hardwood floor approx. 40 mm thick and mechanical locking system * The supply lines are protected in the extendable beams and automatically adjust to the respective low-bed length * 7 pairs of lashing rings that can be folded outwards (LC 10,000 daN) * 6 pairs of threaded blocks on the inner beam for mounting screw-on RUD rings Rear chassis: * Rear chassis with closed outer frame and diamond plate cover * Chassis with excavator bucket, which is closed in the rear half to accommodate the air tanks * 3 pairs of lashing rings that can be folded outwards (LC 5,000 daN) * 1 pair of lashing rings that can be folded outwards (LC 10,000 daN) * 1 pair of lashing rings, horizontally, at the front and rear of the chassis (LC 10,000 daN) Axles: * BPW axles and suspension, all axles hydro-mechanically forced-steered * Technical axle load: 12,000 kg each * Air suspension with lifting and lowering valve Tires: * Tires 245/70 R 17.5 3PMSF - at the manufacturer's choice. Load index (146/146F) Braking system: * WABCO braking system in accordance with EU regulations with EBS-E (2S2M) Paint: * HRM metallization of the entire vehicle chassis with ZINACOR 850 (85% zinc/15% aluminum) to ensure the best corrosion protection * Topcoat with 2 layers of 2K topcoat, solid color in RAL 3002 carmine red, according to the RAL 841GL system Includes accessories: * 2-inch kingpin * One galvanized steel front bulkhead, approx. 400 mm high * Yellow-red air couplings on the galvanized connection strip at the front * Trailer steering, operable from the front and rear via cable remote control with push buttons, with single-axle steering control (without installation in the tractor unit) * Preparation for mounting screw-on container positioning for 1 x 20', 1 x 40' or 1 x 45' containers on the outer beams. Without container locking mechanisms * Hydraulic connections from the gooseneck to the low-bed with multi-coupling instead of screw couplings * Electro-hydraulic unit * Spiral cable for supplying the electro-hydraulic unit and/or the electric winch (approx. 35 mm², approx. 3.5 m long, max. 250A) between the semi-trailer and the tractor unit with plug connection (NATO-NATO) * Yellow reflector tape according to EU regulations on the side, on the extension and at the rear of the semi-trailer * On the gooseneck and at the rear, left and right, one bracket each for the warning signs, including a socket * Manual and description on a USB stick * Central lubrication system with 2 BEKAMAX (Pico) pumps with standard grease NLGI-2 and removable protection around the pumps * 7 pairs of threaded blocks between the lashing rings under the top chord on the outer beam for mounting screw-on RUD VLBG-4 rings * 2nd driving height, approx. 50 mm above the normal driving position, by means of manual operation * On the gooseneck, plug-in aluminum side panels and rear panel, approx. 2,440 x 400 mm (L x H). The rear, galvanized plug-in frames are removable (length of the superstructure

Condition: used, overall weight: 44,000 kg, axle configuration: 2 axles, first registration: 04/2018, Unladen weight: 11,800 kg W = 12,000 mm Extendable forward for front loading of the attached flatbed trailer - Gooseneck in a compact design - L x W: 3,900 x 2,480 mm - Interchangeable 2" kingpin - Integrated hydromechanical steering - Hydraulic lifting and lowering function, including support cylinders - Designed for a technical fifth-wheel load of up to 24 tons - Aluminum side walls, 4-sided - Turning radius: 2,200 mm Flatbed trailer - Low-bed with external tubes - Flatbed length: 6,750 mm, telescoping to 12,250 mm (extension of 5,500 mm) - Flatbed width: 2,550 mm - Height: 200 mm - Loaded height: approx. 300 mm with 100 mm ground clearance, or approx. 350 mm with 150 mm ground clearance - Coupling jaws at the front for connection to the gooseneck 2-axle chassis - Chassis in a compact design - Air-suspended chassis (L x W): approx. 2,750 x 2,550 mm including lifting and lowering valve, with 2 forced-steered axles, manufacturer BPW, track width 1,330 mm - Chassis with kingpin recess Braking system - Two-line, all-wheel air brake system - Progressive central lubrication system - Remote control Ksdpsy U Df Hofx Abnsdp - Loaded fifth-wheel height: 1,250 mm - All 2 axles hydraulically forced-steered

Condition: used, maximum load weight: 36,100 kg, overall weight: 49,000 kg, axle configuration: 2 axles, first registration: 10/2024, next inspection (TÜV): 10/2026, total width: 2,550 mm, Equipment: ABS, You can find our complete vehicle inventory with vehicles available immediately and in the short term on our website. Excerpt from the equipment list. Complete equipment available upon request. Gooseneck: * Gooseneck in SNT design to optimize the loading area length, approximately 3,750 mm long, hydraulically extendable/retractable and adjustable. * Technical saddle load: 25,000 kg * For semi-trailer tractor: 4 x 2, 6 x 2, and 6 x 4 Low-bed: * Low-bed designed as a telescoping bolster bridge in a low-profile design with an extension at the front and a mechanical locking mechanism. * Length x width approximately 6,850 mm x 2,540 mm * The supply lines are protected in the extendable beams and automatically adjust to the respective low-bed length. Axles and Suspension: * PENDEL-AXLE * All axles are hydro-mechanically force-steered. * Hose burst valve on the axle equalization system. * Cylinders with automatic RESET function. * Hydraulic cylinders with shut-off valves and a connector for securing in the raised position. * Technical axle load: 12,000 kg each. * Hydraulic axle equalization. * Tires: 245/70 R 17.5 * Rear chassis: rear chassis with a closed outer frame, with a diamond-plate cover and a continuous prismatic excavator well, approximately 1,250/700 x 505 mm, open at the rear. Braking System: * Braking system from WABCO EBS-E, in accordance with EU regulations, without a connecting cable to the semi-trailer tractor. Paintwork: * Color of the semi-trailer: RAL 3002 carmine red. Included Accessories: * Steel front wall, plug-in, approximately 400 mm high. * 3 kW electric-hydraulic unit for controlling the hydraulic operations, with the exception of hydraulic winches, without installation of the supply connections on the semi-trailer tractor. * Outer beam of the gooseneck with mounting holes for screw-on lashing rings. The first hole is approximately 200 mm from the front, then every approximately 400 mm. 2 pairs of screw-on lashing rings included (LC 5,000 daN). * 1 lashing ring on the left and right sides on the rear slope of the gooseneck (LC 6,000 daN). Kedox Uvllspfx Abnodp * 2-inch kingpin. * One locking point every approximately 500 mm on the extension. * 1 pair of steel ramps with climbing strips and fastening bolts for bridging the mounting hooks of the low-bed. * 1 lashing ring on the left and right sides on the front cross member (LC 10,000 daN). * Lashing rings with retaining spring every approximately 1,200 - 1,300 mm on the outside of the inner beams of the loading area. * Lashing rings with retaining spring every approximately 1,200 - 1,300 mm on the outside of the outer beams of the loading area (LC 10,000 daN) on the upper chord of the outer beams. * Recesses above the lashing rings. * 1 lashing ring hanging on the outside on the left and right sides on the rear cross member (LC 10,000 daN) on the outer beams of the loading area. * Preparation for the removable loading floor. * Mounting rail at the front of the rear chassis for the low-bed for loose loading ramps. * Chassis with beveled corners at the rear. * Mounting rail for loose aluminum loading ramps on the end cross member of the vehicle. * Steerable from the front and rear via cable remote control with push buttons, with single-axle control, without installation in the semi-trailer tractor. * Mechanical pin-tab coupling from the low-bed to the chassis, for changing the loading area or installing extension beams, with electric-pneumatic-hydraulic couplings. * Round NATO socket

Condition: new, axle configuration: > 3 axles, permissible axle load (axle 1): 12,000 kg, permissible axle load (axle 2): 12,000 kg, permissible axle load (axle 3): 12,000 kg, total length: 9,300 mm, total width: 2,540 mm, suspension: air, tire size: 245/70 R17.5, wheelbase: 1,360 mm, color: blue, Year of construction: 2023, Equipment: tail-lift, Colour: Blue Payload weight: 54,465 kg Main Features: Manufacturer: Faymonville Model: MAX 110-Z-4AA-9.30-U Chassis number: YAMT14XX4N0107629 Year: New and unused Weights/Loading Capacity: King-pin load: 23,000 kg Axle load: 12,000 kg Total axle load: 48,000 kg GVW: 71,000 kg Empty weight: 16,535 kg Loading capacity: 54,465 kg Axles: Axle brand: BPW Hydraulic steering Pneumatic suspension with lifting/lowering valve WABCO braking system Tyres: 245 / 70 R17.5 – Michelin (Load index 146/146 F) 1st lift axle Dimensions: Loading length: 9,300 mm Extensions: 6,500 + 6,800 mm Loading floor width: 2,540 mm Loading height: 900 mm Additional Information: Loading floor, double extendable Container locks Outriggers in width + outriggers (wood) for extension in width Lashing rings Set of double folding loading ramps Central lubrication 1x spare wheel + holder JOST landing gear Electric system 24 Volt King-pin 2.0″ One galvanised steel headboard Electrically operated hydraulic pump Manual steering Twist locks = Further Information = General Information Year of construction: 2023 Axle configuration Kdjdjuu Hcfepfx Abnsp Tyre size: 245/70 R17.5 Suspension: Air suspension Rear axle 1: Twin tyres; Lift axle; Max. axle load: 12,000 kg; Steered; Axle brand: BPW; Tyre tread depth left inside: 100%; Tyre tread depth left outside: 100%; Tyre tread depth right inside: 100%; Tyre tread depth right outside: 100% Rear axle 2: Twin tyres; Max. axle load: 12,000 kg; Steered; Tyre tread depth left inside: 100%; Tyre tread depth left outside: 100%; Tyre tread depth right inside: 100%; Tyre tread depth right outside: 100% Rear axle 3: Twin tyres; Max. axle load: 12,000 kg; Steered; Tyre tread depth left inside: 100%; Tyre tread depth left outside: 100%; Tyre tread depth right inside: 100%; Tyre tread depth right outside: 100% Rear axle 4: Twin tyres; Max. axle load: 12,000 kg; Steered; Tyre tread depth left inside: 100%; Tyre tread depth left outside: 100%; Tyre tread depth right inside: 100%; Tyre tread depth right outside: 100% Weights Empty weight: 16,535 kg Payload: 54,465 kg GVW: 71,000 kg Functional Height of loading platform: 65,535 cm Extendable structure: Yes Condition General condition: very good Technical condition: very good Optical condition: very good Financial information Price: On request

Condition: good (used), machine/vehicle number: YAFTL6002R0035345, loading space length: 14,800 mm, loading space width: 2,500 mm, loading space height: 9,000 mm, Year of construction: 2024, = Additional options and accessories = - Rear air suspension - Front air suspension - Drum brake system Kdjdpfox Rtiasx Abnsp = Further information = Payload: 81,100 kg Gross Vehicle Weight (GVW): 81,100 kg Technical condition: good Visual condition: good Front tyre condition: 60 Front tyres: 245/70 R17.5 Rear tyres: 245/70 R17.5 Last inspection: 2025-12-28 Contact Lastas Sales for further information.

Condition: good (used), axle configuration: 3 axles, permissible axle load (axle 1): 10,700 kg, permissible axle load (axle 2): 10,700 kg, permissible axle load (axle 3): 10,700 kg, first registration: 03/2013, suspension: air, tire size: 235/75R17.5, color: red, Year of construction: 2013, = Additional Options and Equipment = - Air suspension = Notes = Faymonville Euro low-loader with detachable gooseneck for sale Specifications 4 wheel recesses, each 2 meters Width: 2.55 m Extensions: 0.25 m Low bed: 8 meters Deck above the axles: 4.30 m Gooseneck top: 3.10 m Loading height (driving position): 0.50 m German registration Tires at 80 percent SAF axles 3 steering axles Robust and well-maintained low-loader, immediately ready for heavy-duty transport. = Further Information = Axle configuration Tire size: 235/75R17.5 Kdjdpfxoyw Sxto Abnsp Axle brand: SAF Suspension: Air suspension Rear axle 1: twin tires; max. axle load: 10,700 kg; steered; tire tread left inner: 70%; left outer: 70%; right inner: 70%; right outer: 70% Rear axle 2: twin tires; max. axle load: 10,700 kg; steered; tire tread left inner: 70%; left outer: 70%; right inner: 70%; right outer: 70% Rear axle 3: twin tires; max. axle load: 10,700 kg; steered; tire tread left inner: 70%; left outer: 70%; right inner: 70%; right outer: 70% Weights Unladen weight: 14,700 kg Payload: 17,400 kg Gross vehicle weight: 32,100 kg Condition Technical condition: good Visual condition: good Product Safety Manufacturer: Faymonville BE Additional Information Contact Gerrit Haverhoek for further information.

Condition: new, empty load weight: 9,600 kg, maximum load weight: 53,400 kg, overall weight: 63,000 kg, axle configuration: > 3 axles, loading space length: 12,400 mm, loading space width: 2,540 mm, loading space height: 1,340 mm, suspension: air, tire size: 385/65 R22.5, color: grey, Equipment: ABS, Loading area: -Loading area with approx. 30 mm thick hardwood floor -10 pairs of lashing rings can be folded outwards Seat posts: -JOST seat posts with 2-speed gearbox for 24 t lifting load Axles and tires: -BPW axles, techn. 10,000 kg, first axle rigid, all other axles hydro-mechanically forced steered, mounted on turntable -Air-sprung with lifting and lowering valve Kdsdpfxjrq Dlfj Abnjp -axle tool -385/65 R22.5 tires Brake system: -WABCO brake system in accordance with EU regulations with EBS-E (4S3M) Steel construction: -steel construction made of high-strength fine-grained steels -Steel grades: -S355J2+N/S355MC -S690QL/S700MC Electrical system: -Electrical system in accordance with EU regulations, 24 volt lighting -ASPÖCK UNIBOX on the front connection strip with 24N, 24S & 15-pin sockets Connection in accordance with ISO: 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Paintwork: -First-class and durable corrosion protection of the standard shot-blasted welded frame guaranteed by a 2-component zinc dust primer A high-quality 2-component top coat in a single color in nova grey -Rear part metallized and painted in RAL 9010 Accessories included: -Loading area with approx. 30 mm thick hardwood floor -2" kingpin -One galvanized steel end wall approx. 1,200 mm high EN12642-XL -Yellow-red air couplings on the galvanized connection strip at the front -4 restraining shoes with holder on the front wall -Storage for 1,000 mm stanchions in the rear central support -On the gooseneck and on the rear panel on the left and right, one bracket each for the warning signs including socket -Reverse steering can be operated from the front and rear via cable remote control using pushbuttons, with tracking control of the axles -Electric hydraulic unit -White reflective tape in accordance with EU regulations on the side of the trailer and red at the rear -12 pairs of stanchion pockets for 100 x 50 mm stanchions in the outer frame of the cargo bed -European reflector plates at the rear of the trailer -One bracket for a rotating beacon at the rear of the trailer -One mud flap at the rear of the trailer -Manual and description on USB stick -BEKAMAX (Pico) central lubrication system with NLGI-2 standard grease and removable protection around the pump -TPMS tire pressure monitoring system: -For correct display, the motor vehicle must be able to transmit and display this data -Lift axle on the front axle with control by TEBS E depending on the current axle load and the current load status -Radio remote control for steering in addition to the cable remote control, with indicator lights on the receiver for tracking control -5 pairs of stanchion pocket rails, mounted transversely in the cargo bed, for 100 x 50 mm stanchions -Speed stickers 80 km/h at the rear and on both sides -Adjustable access ladder mounted on the left and right in the direction of travel -2 reversing lights mounted on the rear panel -Load manometer for determining the axle loads including load diagram HRM metallization of the outer frame Complete steel construction shot-blasted, then the defined visible surfaces hot-finished in metallization with ZINACOR 850 (zinc 85% - aluminium 15%)

Condition: used, empty load weight: 15,550 kg, maximum load weight: 47,450 kg, overall weight: 63,000 kg, axle configuration: > 3 axles, first registration: 11/2024, loading space length: 8,800 mm, loading space width: 2,540 mm, loading space height: 860 mm, suspension: air, tire size: 235/75 R 17,5, Year of construction: 2024, Equipment: ABS, With every used semi-trailer, you receive a current and complete inspection and function report. Gooseneck: - Gooseneck in SNT design to optimize loading platform length, approx. 3,700 mm long - Gooseneck rear with tapering, approx. 1,000 mm x 10° Loading Area: - Extendable loading area, length approx. 8,800 mm, with rear tapering approx. 500 mm x 10° - Recess in the loading area, extending into the beveled section to accommodate the excavator’s bucket arm - Pneumatic locking with conical locking bolts and reinforced locking positions - Hardwood decking on the beveled section of the loading area Ramps: - 1 pair of two-piece steel ramps, approx. 4,350 mm long and 900 mm wide - Ramps with hardwood decking - Hydraulically folding ramp tips - Ramps hydraulically adjustable individually by approx. 235 mm outward and 215 mm inward - Square climbing bars 20 x 30 mm, spaced approx. every 200 mm along the outer frame of the ramp Axles and Suspension: - BPW axles and suspension, 1st axle self-steering, all other axles hydromechanically forced steering - Technical axle load: 12,000 kg - Air suspension - Tires 235/75 R 17.5 - TPMS Tire Pressure Monitoring System - TPMS Tire sensors Accessories included: - Removable steel front wall, approx. 400 mm high - 3 kW electro-hydraulic power unit for hydraulic operations - 1 spare wheel Ksdpfx Aboypb Akenodp - Outer beams of the gooseneck with mounting holes for bolt-on lashing rings - First hole approx. 200 mm from the front, then at approx. 400 mm intervals - 2 pairs of screw-in lashing rings included - 1 pair of horizontal lashing rings at the rear of the gooseneck - 1 pair of removable anodized ALU side boards, approx. 400 mm high, on the gooseneck - 1 removable anodized ALU rear board, approx. 400 mm high, on the gooseneck - 2" kingpin - Round NATO socket on the front connection strip - 4 wheel chocks - Mechanical landing legs with 2-speed gearbox and crank - 1 intermediate table, approx. 300 mm wide - 1 pair of lashing rings on the front crossmember - 8 pairs of recessed, fold-out lashing rings in the loading area outer frame - Extendable (galvanized) widening elements, approx. 230 mm per side - Wheel recesses with square climbing bars, 15 x 15 mm, continuous in front of the axles up to the gooseneck crossmember, approx. 700 x 410 mm - ALU covers for the wheel recesses - Lockable aluminium elements on the extension tubes of the widening sections - Widenable U-profiles for ALU covers - Wheel recesses with square climbing bars, 15 x 15 mm, between 1st and 2nd axle, approx. 1,480 x 700 x 410 mm - Lockable aluminium elements on the extension tubes of the widening sections - 1 pair of mechanical rear supports - Remote steering from front and rear via cable remote control, with axle single-wheel tracking control - 1st axle with automatic lift axle function and starting aid compliant with EU Regulation 2021/535 - Under the gooseneck and on the rear crossmember, left and right, each with a 7-pin socket and holder for warning signs - Square climbing bars 20 x 30 mm, approx. every 200 mm on the outer frame of the beveled part of the loading area - Central lubrication system with 1 BEKAMAX brand pump - Radio remote control for remote steering, in addition to the cable remote - Wabco Smart Board System - 4 warning boards, approx. 423 x 423 mm, extendable by approx. 400 mm

Condition: new, empty load weight: 15,550 kg, maximum load weight: 47,450 kg, overall weight: 63,000 kg, axle configuration: 3 axles, loading space length: 8,800 mm, loading space width: 2,540 mm, loading space height: 860 mm, suspension: air, tire size: 235/75 R 17,5, color: grey, Equipment: ABS, Gooseneck: Kdsdpsk Aht Usfx Abnep -Gooseneck in SNT design for optimized loading area length, approximately 3,700 mm long -Gooseneck with rear bevel approximately 1,000 mm x 10° Loading Platform: -Loading platform in extendable design, approximately 8,800 mm long, with bevel at the rear approximately 500 mm x 10° -Recess in the loading platform and into the bevel for accommodating the excavator arm -Pneumatic locking system with tapered locking pins and reinforced locking positions -Hardwood decking on the bevel of the loading platform Ramps: -1 pair of two-part steel ramps with a length of approximately 4,350 mm and a width of approximately 900 mm -Ramps with hardwood decking -Hydraulically folding ramp ends -Ramps can be individually hydraulically moved outwards by approximately 235 mm and inwards by approximately 215 mm -Square ladder strips 20 x 30 mm, approximately every 200 mm on the outer frame of the ramp Axles and Suspension: -BPW axles and suspension, 1st axle with steering knuckle, all other axles with hydromechanical forced steering -Technical axle load: 12,000 kg -1st axle with electromagnetic reverse lock via reverse gear and can be activated manually -Air suspension with lifting and lowering valve -Tires 235/75 R 17.5, twin tires -TPMS tire monitoring system according to ECE R141 -TPMS tire monitoring sensors mounted in all wheels including spare wheel Included accessories: -Steel front wall, plug-in, approximately 400 mm high -3kW electro-hydraulic unit for controlling the hydraulic operations, with the exception of hydraulic winches -Parking position on the gooseneck for the warning signs when not in use -1 spare wheel -On the gooseneck, 1 pair of plug-in aluminum sideboards, approximately 400 mm high, anodized -On the gooseneck, 1 plug-in aluminum rear wall, approximately 400 mm high, anodized -Approximately 40 mm thick hardwood decking above the gooseneck, checkered plate decking above the kingpin -2" kingpin -Guide plate from the gooseneck for the fifth wheel plate, approximately 500 mm wide -4 chock blocks -Mechanical landing gear with 2-speed gearbox and crank -JOST Module B – static test load = 50,000 kg -1 intermediate table, approximately 300 mm wide -Extensions (galvanized), extendable by approximately 230 mm on each side -Wheel recesses with square ladder strips -Aluminum covers for the wheel recesses -1 pair of mechanical rear supports -Steering assistance at the front and rear, operable via cable remote control, with single-axle monitoring -1st axle with automatic lift axle function -Central lubrication system with 1 pump, brand BEKAMAX -Wireless remote control for operating the steering assistance, in addition to the cable remote control, with 2 indicator lights on the receiver for single-axle monitoring -Wabco Smart Board system -4 warning signs, approximately 423 x 423 mm, extendable by approximately 400 mm, incl. 2 position lights and mounts for rotating beacon

Condition: new, empty load weight: 15,420 kg, maximum load weight: 61,080 kg, overall weight: 76,500 kg, axle configuration: > 3 axles, loading space length: 8,600 mm, loading space width: 2,540 mm, loading space height: 900 mm, tire size: 235/75/r17,5, color: grey, Equipment: ABS, Gooseneck: Gooseneck with rear bevel of approx. 750 mm x 10° 3 pairs of lashing rings Hardwood decking 30 mm thick Loading platform: Loading area in extendable design with rear bevel of approx. 500 mm x 8° 8 pairs of lashing rings can be folded outwards 1 pair of lashing rings lying in the front of the cargo bed Cut-outs in the outer frame of the cargo bed for attaching lashing straps Hardwood flooring approx. 48 mm thick, checker plate flooring over the axles Two-part steel ramps: A pair of galvanized two-part steel ramps approx. 2,750 + 1,400 x 800 mm with approx. 48 mm thick hardwood decking. Ramp with hydraulically folding and unfolding ramp sections, hydraulic lifting gear and hydraulically movable. Maximum load per pair: 50,000 kg. Seat posts: - JOST fifth wheels (mechanical) with 2-speed gearbox for 24t lifting load (50t test load). Axles and tires: BPW axles and suspension, 4th + 5th axle self-steering Technical axle load: 12,000 kg 4th and 5th axles with electro-magnetic reverse lock via reverse gear and manual activation Tires 235/75 R 17.5 3PMSF Brake system: Brake system in accordance with EU regulations with EBS-E (4S3M) Sockets and lighting: Electrical system in accordance with EU regulations, 24 volt lighting ASPÖCK-NORDIK (ASS3) ASPÖCK-UNIBOX on the front connection strip with 24N, 24S & 15-pin sockets Connection according to ISO 24N ISO-1185 24S ISO-3731 15 pole ISO-12098 Paint finish: First-class and durable corrosion protection of the standard shot-peened welded frame guaranteed by a 2-component (2K) zinc dust primer A high-quality 2-component (2K) top coat in a single color in MB 7350 nova grey Rear section metallized and painted in RAL 9010 (pure white) No metallic paint finish possible Steel construction: Ksdpfol Sl Izox Abnjdp Steel construction made from high-strength fine-grained steels Steel grades: S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa) Accessories: One spare wheel with holder in front of the bulkhead 2" kingpin One galvanized steel bulkhead approx. 400 mm high Yellow-red air couplings on the galvanized connection strip at the front 2 restraining shoes with holder on the bulkhead Mounting in the rear area of the gooseneck for ALU docking lights A bracket for a rotating beacon at the rear of the trailer Galvanized supports under the bevel of the loading area White reflective tape in accordance with EU regulations on the sides, on the extension and red at the rear Electro-hydraulic unit at the rear under the cargo bed A holder for the warning signs, including a socket, on the gooseneck and on the rear panel on the left and right respectively Control valves for the ramps mounted on the right-hand side of the trailer A mud flap at the rear of the trailer Manual and description on USB stick 3.5" kingpin supplied loose ALU drop sides and rear wall can be plugged onto the gooseneck approx. 2,440 x 400 mm (LxH) The rear galvanized stanchions are removable (length of the body approx. 2,560 mm) 3 pairs of WADER container pockets in the loading area for a 20' (30') or a 40' container 6 pairs of stanchion pockets for 100 x 50 mm stanchions in the outer frame of the cargo bed Galvanized extensions, extendable by approx. 230 mm per side Lift axle on the front axle with control by TEBS E depending on the current axle load and the current load status Square climbing rails 20 x 20 mm every 200 mm on the outer frame of the loading area slope On the chequer plates, above the kingpin and the load floor

Condition: new, empty load weight: 10,700 kg, maximum load weight: 38,800 kg, overall weight: 49,500 kg, axle configuration: 3 axles, loading space length: 9,300 mm, loading space width: 2,540 mm, loading space height: 860 mm, suspension: air, tire size: 235/75 r 17,5, color: grey-black, Equipment: ABS, Gooseneck: •Gooseneck with angled front corners at 45° and rear taper of approximately 750 mm x 10° •3 pairs of lashing rings •Hardwood decking, 30 mm thick Extendable platform: •Extendable platform with rear taper of approximately 1,000 mm x 8° •Cutouts in the outer frame of the platform for attaching lashing straps •Hardwood decking approximately 48 mm thick, with chequered plate decking over the axles Ksdpfjhlz S Nex Abnodp Two-piece steel ramps: •One pair of galvanized, two-piece steel ramps with approximately 48 mm thick hardwood decking •Ramp with hydraulically folding ramp sections, hydraulic lifting mechanism and hydraulically adjustable •Maximum load per pair: approximately 40,000 kg Axles and tires: •BPW axles and suspension, 2 fixed axles, 1 steered axle •Technical axle load: 12,000 kg •Electro-magnetic reversing lock activated via reverse gear and manually •Air suspension with lifting and lowering valve •Axle tool •235/75 R 17.5 3PMSF Braking system: •WABCO braking system according to EU regulations with EBS-E Paint finish: •First-class and durable corrosion protection of the standard bead-blasted welded frame is guaranteed by a 2-component zinc dust primer •High-quality 2-component topcoat, single-color in MB 7350 Novagrau •Rear section metallized and painted in RAL 9010 Kingpin: •JOST kingpin with 2-speed gearbox for 24t lifting capacity (50t test load). Steel structure: •Steel structure made of high-strength fine-grain steels •Steel grades: •S355J2+N/S355MC •S690QL/S700MC Electrical system: •Electrical system according to EU regulations, lighting 24 volts •ASPÖCK-UNIBOX on the connection strip at the front with 24N, 24S and 15-pole sockets Included accessories: •One spare wheel with holder •One galvanized steel front bulkhead, approximately 400 mm high •Yellow-red air couplings on the galvanized connection strip at the front •4 chocks •One holder for a rotating beacon at the rear of the semi-trailer •Mounting in the rear area of the gooseneck for aluminum support ramps •Galvanized folding supports under the taper of the platform •Cover plates to bridge the gap between ramps and platform •White reflector tape according to EU regulations on the side, on the extension and at the rear in red •Electro-hydraulic unit at the rear, under the platform •On the gooseneck and on the ramps, one holder each on the left and right for warning signs including socket •Control valves for the ramps mounted on the right side of the semi-trailer •Aluminum side and rear walls on the gooseneck, approximately 2,440 x 400 mm •The rear, galvanized stake pockets are removable (length of the superstructure approximately 2,560 mm) •Four warning signs that extend by approximately 400 mm with a position light •3 pairs of WADER container pockets in the platform for a 20ft, 30ft or 40ft container •6 pairs of stake pockets (100x50 mm) in the outer frame of the platform •Extensions, galvanized, extendable by approximately 230 mm on each side •Square ladder rails 20 x 20 mm every 200 mm on the outer frame of the platform taper •A lacquered sand layer as an anti-slip coating on the chequered plates, over the kingpin and the platform •Load manometer for determining axle loads, including load diagram •HRM metallization (High Resistance Metallization) of the outer frame •Complete steel structure bead-blasted, then the defined visible surfaces hot-dip metallized with ZINACOR 850 (zinc 85% - aluminum 15%)

Condition: new, empty load weight: 11,000 kg, maximum load weight: 38,500 kg, overall weight: 49,500 kg, axle configuration: 3 axles, loading space length: 9,300 mm, loading space width: 2,540 mm, loading space height: 860 mm, suspension: air, tire size: 235/75 R 17,5, color: grey, Gooseneck: - Gooseneck with rear chamfer approx. 750 mm x 10° - 3 pairs of lashing rings (LC 5,000 daN) - 30 mm thick hardwood flooring Loading Area: - Telescopic loading area with rear bevel approx. 1,000 mm x 8° - 1 pair of permanently installed wheel recesses in front of the axles, approx. 2,850 x 970 x 400 mm - Wheel recesses fitted with 15 x 15 mm square anti-slip bars and widened at the lower section - Between the 1st and 2nd axle, one pair of permanently installed wheel recesses with cover, approx. 1,610 x 970 x 400 mm - Recess in the rear slope projecting into the loading area for excavator dipper arm storage, approx. 2,900 x 750 x 210/290 mm - 1 pair of horizontal lashing rings at the front of the loading area (LC 10,000 daN) - 5 pairs of fold-out lashing rings to the outside (LC 5,000 daN) - 2 pairs of fold-out lashing rings to the outside (LC 10,000 daN) - 2 pairs of lashing rings in the excavator arm recess (LC 5,000 daN) - Cut-outs in the outer frame of the loading area for securing straps (LC 2,000 daN) - Including 3-piece removable galvanized covers over the wheel recesses – max. point load 3.5 t per section Two-part Steel Ramps: - One pair of galvanized two-part steel ramps, approx. 2,750 + 1,400 x 800 mm, with 48 mm thick hardwood surfacing - Ramps with hydraulically foldable ramp sections, hydraulic lifting gear, and hydraulically transverse-adjustable Axles and Tires: - BPW axles and suspension, 2 rigid axles, 1 self-steering trailing axle - Technical axle load: 12,000 kg - Electromagnetic reverse lock, activated via reverse gear or manually - Air suspension with raise/lower valve - Axle tool kit - Tires: 235/75 R 17.5 - TPMS tire pressure monitoring system according to ECE R 141 Accessories Included: - At the gooseneck and at the rear, left and right, each with a holder for warning signs, including socket - One spare wheel - 2" king pin - One galvanized steel front wall approx. 400 mm high - Yellow-red air couplings on the galvanized front connection panel - 4 wheel chocks - Galvanized extensions, extendable by approx. 230 mm each side - Galvanized folding supports under the sloped rear of the loading area - Holder for rotating beacon at the rear of the trailer - Cover plates to bridge the gap between the ramps and loading area - White reflective tape in accordance with EU regulations on the sides and on the extension, red at the rear - Rear-mounted electro-hydraulic power unit underneath the loading area - Ramp control valves mounted on the right-hand side of the trailer - European reflective signs (red-yellow) at the rear of the trailer - Four extendable warning signs, about 423 x 423 mm, each with a position light (extendable about 400 mm) - Mounting for rotating beacon on the warning signs - On the gooseneck, plug-in aluminium side walls and rear wall ca. 2,440 x 400 mm - The rear, galvanized plug-in posts are removable (body length approx. 2,560 mm) - 2 pairs of WADER container pockets in the loading area for one 20ft or 30ft container - 3 pairs of stake pockets for 100 x 50 mm plug-in stakes in the outer frame of the loading area Kjdpeup U Hzofx Abnodp - One removable, galvanized intermediate table with 1 pair of WADER container pockets - Square anti-slip bars 20 x 20 mm every 200 mm on the outer frame of the rear slope - Painted sand grip layer as anti-slip protection on the checker plates on the gooseneck and loading area - 80 km/h speed stickers at the rear and on both sides - Ax

Condition: new, empty load weight: 9,450 kg, maximum load weight: 35,550 kg, overall weight: 45,000 kg, axle configuration: 3 axles, loading space length: 9,500 mm, loading space width: 1,560 mm, total width: 2,550 mm, tire size: 385/65 R 22,5, color: grey, Equipment: ABS, Gooseneck: - Gooseneck designed as a loading deck, fitted with aluminum chequer plate - Front tapered approx. 45° - Hydraulic lifting arm, lift/lower range approx. -280/+250 mm - Two kingpin positions at 2,300 mm and 2,000 mm from DSR - Suitable for tractor units: 4x2, 6x2, or 6x4 Loading Bay: - Loading bay, length approx. 9,500 mm, with bottom-mounted angle profiles for pallet mounting (distance from kingpin to center of axle assembly approx. 8,000 mm) Axles, Suspension and Tyres: - BPW stub axles, with drum brakes and independent wheel suspension, hydraulic axle compensation with lift and lower function - Axle lowering lock in case of suspension airbag failure, designed for max. pallet height 150 mm - Tyres: 385/65 R 22.5 - TPMS tyre pressure sensors installed in all wheels including the spare - TPMS tyre pressure monitoring system compliant with ECE R 141 Surface Treatment: - Entire steel structure automatically shot-blasted after welding using a turbine blasting system - Second blasting with corundum to optimise coating adhesion - HRM metallisation of the complete vehicle chassis with ZINACOR 850 (85% zinc/15% aluminium) for maximum corrosion protection - Final coat with two layers of 2K topcoat, single colour in Novagrau (DB 7350) - Paint system tested in salt spray test to ISO 9227-NSS; cavity sealing with special wax Included Accessories: - Removable steel front wall, approx. 400 mm high Kodpeygvc Hefx Abnsdp - Tool box with lid, integrated in the rear section of the gooseneck, approx. 640 x 700 x 215 mm - Removable aluminium rear wall on the gooseneck, approx. 400 mm high, anodised - One pair of folding aluminium sideboards on the gooseneck, approx. 400 mm high, anodised - 2" kingpin - 3 pairs of recessed lashing rings on the gooseneck (LC 6,300 daN) - At the front connection rail, yellow-red air couplings; operation lighting for the gooseneck, suspension, and hydraulic load restraints with on/off switch - Mechanical drop tube supports for approx. 48,000 kg support load - Access ladder mounted front right with 2 detachable handrails - WABCO Roll Stability Support (RSS) - 9 pairs of lashing rings (LC 6,300 daN) mounted on the longitudinal beams - Grating platform, level with the guiding rails for load securing, fitted to the longitudinal beams - Hydraulic preparation, including control unit, for mounting 3 pairs of our hydraulic load restraints - First and last axle manually liftable on left and right - Storage box behind axle assembly, left and right, splash-proof - Tapered rear edge for easier pallet loading - Rear lashing eyes mounted on the tail crossmember for mechanical bracing - 7-pin socket on the tail crossmember - Electro-hydraulic power unit - 4 wheel chocks with holders - 2 axle load gauges mounted on the left side incl. axle load diagram - 3 pairs of hydraulic load restraints with swivel arms, moveably mounted to longitudinal beams - Rear door with cross bracing, hinged left and hydraulically locked right, can be secured horizontally at 90°, 105°, and 270° - Folding underride guard for transporting up to 4 empty standard pallets - 1 spare wheel - Number plate holder including lighting, rear left on the trailer - Round NATO socket on front connection rail (Maeler & Kaege VG 96 917) - Central lubrication system with 1 pump, brand BEKAMAX, standard grease version

Condition: new, empty load weight: 12,300 kg, maximum load weight: 37,200 kg, overall weight: 49,500 kg, axle configuration: 3 axles, loading space length: 9,300 mm, loading space width: 2,480 mm, loading space height: 860 mm, suspension: air, tire size: 235/75 R17.5, color: grey, Equipment: ABS, Gooseneck: -Gooseneck with rear bevel of approx. 750 mm x 10° -Hardwood covering 30 mm thick Two-piece steel ramps: -A pair of galvanized two-part steel ramps approx. 3,185x1,420x1,250 mm with grating decking -Ramp with hydraulically folding and unfolding ramp sections, hydraulic lifting gear Gooseneck: -Gooseneck with rear bevel of approx. 750 mm x 10° -3 pairs of lashing rings -Hardwood decking 30 mm thick Two-part steel ramps: -One pair of galvanized two-part steel ramps approx. 3,185x1,420x1,250 mm with grating covering -Ramp with hydraulically folding and unfolding ramp sections, hydraulic lifting gear -Maximum load per pair: 30,000 kg Kdjdpfxetvfkfj Abnsp Loading area: -Loading surface with rear slope of approx. 1,000 mm x 8° -Hardwood flooring approx. 48 mm thick, checker plate flooring over the axles Axles and tires: -BPW axles and suspension, two axles rigid, one axle self-steering -Air suspension with lifting and lowering valve The self-steering axles with electro-magnetic reverse lock can be activated via reverse gear or manually -235/75 R17.5 3PMSF tires Accessories included: -1 Spare wheel with holder -TPMS tire pressure monitoring system according to ECE R 141 -2" kingpin -Galvanized steel bulkhead -Yellow-red air couplings on the galvanized front connecting strip -4 restraining shoes with holder on the bulkhead -Mounting in the rear area of the gooseneck for ALU docking ramps -3 height aluminum boards -Galvanized folding supports under the bevel of the cargo bed Height-adjustable tarpaulin superstructure (3,960 mm) -Galvanized bulkhead with a tensioning mechanism for the sliding curtain -Height-adjustable by approx. 400 mm -"EDSCHA" brand roof can be moved forwards on ALU roof rail profiles bolted to the front and rear wall -3 pairs of sliding stanchions in the loading area -The body can be hydraulically widened at the rear to the left and right by approx. 750 mm -Sliding roof with pivoting portal support -Sliding tarpaulin with 700 mm reserve in length, with tension belts at approx. 600 mm intervals -Height top edge of body approx. 3,960 mm -Driving with the sliding tarpaulin open is not permitted and will damage the tarpaulin -Cover plates to bridge the free space between ramps and loading area -Electric hydraulic unit at the rear, under the cargo bed -On the gooseneck and on the ramps on the left and right, one bracket each for the warning signs including socket -Control valves for the ramps mounted on the right-hand side of the trailer -6 pairs of stanchion pockets for 100 x 50 mm stanchions in the outer frame of the cargo bed -Lift axle on the front axle -Grating in the bevel of the loading area C40/4 (point load 3.4 tons on an area of 20 x 20 cm) -One INOX toolbox 565 x 290 x 810 mm in the direction of travel on the right between the axles -A layer of sand painted onto the chequer plates on the gooseneck and on the loading area to prevent slipping -BEKAMAX (Pico) central lubrication system with NLGI-2 standard grease and removable protection around the pump -Four warning panels approx. 423 x 423 mm, extendable by approx. 400 mm, with a position light -Load manometer for determining the axle loads including load diagram -HRM metallization (High Resistance Metallization) of the outer frame -Complete steel construction shot-blasted, then the defined visible surfaces hot-finished in metallization with ZINACOR 850 (zinc 85% - aluminium 15%)

Condition: new, empty load weight: 29,600 kg, maximum load weight: 72,400 kg, overall weight: 102,000 kg, axle configuration: > 3 axles, loading space length: 6,650 mm, loading space width: 2,840 mm, loading space height: 550 mm, tire size: 285/70 R19.5, color: grey, operation weight: 29,600 kg, Equipment: ABS, Gooseneck: -Hydraulic gooseneck Raisable/lowerable and removable -Length approx. 3,650 mm -For tractor units: 6 x 4 or 8 x 4 2-axle chassis at the front: Kdodowcmhajpfx Abnep -Hook attachments at the front and rear -Chassis length x chassis width approx. 2,200 mm x 2,850 mm Excavator bridge "BB-A": -Telescopic excavator bridge "BB-A" with drive-over bridge hooks at the front and with bolt-and-link coupling at the rear -Length x base width approx. 6,650 mm x 2,850 mm -Beam height x beam width approx. 400 mm x 1,350 mm -Loading height 550 mm with ground clearance 150 mm 4-axle chassis at the rear: -Mechanical bolt-and-link coupling for attaching a low bed at the front, end cross member at the rear -Chassis length x Chassis width approx. 5,480 mm x 2,850 mm - Extensive lashing positions Pendulum axle and tires (front and rear chassis): - "Pendulum axle", all axles hydromechanically steered - Hose rupture valve on the axle compensation cylinder with automatic reset function - Hydraulic cylinder with shut-off valves and pins for securing in the raised position - Final axle paint finish with two coats of 2-component paint in MB 7350 Nova Gray - Technical axle load: 12,000 kg - Hydraulic axle compensation - Tires 285/70 R19.5 Steering: - Front and rear steering can be operated via cable remote control using push buttons, with axle alignment control - Power socket for operating the steering system on the chassis Gooseneck -Cable remote control with pushbuttons including axle alignment control Accessories included: -Yellow-red air couplings on the galvanized connection strip at the front -Steel bulkhead, approx. 400 mm high -4 wheel chocks -3.5" kingpins -One 7-pin socket on the left and right rear of the gooseneck for the warning sign -Gallows with winch for spare wheel on the front of the gooseneck -Truck hydraulic connection with flow regulator (40 l/min), including a boom for suspending the supply lines. The tractor unit's tank must hold at least 80 liters with couplings -Aluminum side walls and rear wall that can be attached to the gooseneck, approx. 400 mm high, anodized -Control lever on the gooseneck protected by a hinged cover -A separate air connection with air gun on the gooseneck -Bekamax central lubrication system, 1x on the Gooseneck, 1x on the 2-axle chassis and 1x on the 4-axle chassis - Variomax tool kit - Multi-coupling hydraulic connections on the gooseneck and in the area of the low-loader hook attachment - 2 spare wheels - One 7-pin socket on the left and right, front and rear of the rear chassis for the warning sign - Front chassis with a separate air connection for pneumatic screwdrivers - Foldable extensions with steel mattresses, adjustable in width from approx. 2,850 mm to approx. 3,250 mm - The steel mattresses can be inserted in two positions to create a lowered loading area - Steel mattresses with rubber flooring, approx. 12 mm thick - Screw-in option (⌀ 40 mm) every approx. 500 mm outside on the upper chord of the outer tube of the excavator bridge for screw rings - One locking point every approx. 500 mm on the extension with mechanical locking Locking mechanism -A socket on the rear chassis for the cable remote control of the self-steering system -Two reversing lights on the rear panel -Four warning signs, approximately 423 x 423 mm, extendable by approximately 2,000 mm, with a position light -One work light, left and right, on the rear panel of the gooseneck with separate on/off switches -Two stainless steel tool boxes, approxim

Condition: new, empty load weight: 10,300 kg, maximum load weight: 39,200 kg, overall weight: 49,500 kg, axle configuration: 3 axles, loading space length: 9,300 mm, loading space width: 2,540 mm, loading space height: 860 mm, suspension: air, tire size: 235/75 R 17.5, color: grey, Equipment: ABS, Gooseneck: -gooseneck with rear bevel of approx. 750 mm x 10° -3 pairs of lashing rings (LC 5,000 daN) -Hardwood decking 30 mm thick Loading area: -Loading surface can be raised and lowered hydraulically after the gooseneck Length approx. 2,800 mm, with rear slope of approx. 1,000 mm x 8° Cut-outs in the outer frame of the cargo bed for attaching tensioning straps (LC 2,000 daN) -Hardwood flooring approx. 48 mm thick, checker plate flooring over the axles Two-part steel ramps: -One pair of galvanized two-part steel ramps approx. 2,750 + 1,400 x 800 mm with approx. 48 mm thick hardwood decking -Ramp with hydraulically folding and unfolding ramp sections, hydraulic lifting gear and hydraulically movable -Maximum load per pair: 40,000 kg Axles, suspension and tires: -BPW axles and suspension, 2 axles rigid, 1 axle self-steering -Technical axle load: 12,000 kg -Electromagnetic reverse lock via reverse gear and can be activated manually -Air suspension with lifting and lowering valve -axle tool -235/75 R 17.5 3PMSF tires -TPMS tire pressure monitoring system in accordance with ECE R 141 Accessories included: -One spare wheel with holder in front of the bulkhead -2" kingpin -One galvanized steel bulkhead approx. 400 mm high -Yellow-red air couplings on the galvanized connection strip at the front -4 pieces of restraining shoes -Galvanized folding supports under the bevel of the cargo bed -A bracket for a rotating beacon at the rear of the trailer -Cover plates to bridge the space between the ramps and the cargo bed -White reflective tape in accordance with EU regulations on the side of the trailer and red at the rear -Electric hydraulic unit at the rear, under the cargo bed -One bracket for the warning signs on the gooseneck and on the ramps on the left and right, including socket -Control valves for the ramps fitted on the right-hand side of the trailer -European reflector signs (red/yellow) at the rear of the trailer -Manual and description on USB stick -ALU drop sides and rear wall can be plugged onto the gooseneck approx. 2,440 x 400 mm -The rear, galvanized stanchions are removable (length of the body approx. 2,560 mm) -An electric cable winch with radio remote control approx. 5,400 kg lifting force, including 9.5 mm thick wire rope 24 m long with rope guide roller -Screwed 5to ring for reeving the cable winch cable on the neck without deflection pulley -2 pairs of WADER container pockets in the loading area for a 20ft container -6 pairs of stanchion pockets for 100 x 50 mm stanchions in the outer frame of the cargo bed -Lift axle on the front axle with control by TEBS E depending on the current axle load and the current loading condition -7 pairs of recessed lashing rings along the central beam (LC 5,000 daN) -1 pair of recessed lashing rings along the central beam at the rear of the bevel (LC 10,000 daN) -A layer of sand painted onto the chequer plates on the gooseneck and on the cargo bed to prevent slipping -BEKAMAX (Pico) central lubrication system with NLGI-2 standard grease and removable protection around the pump -Four warning signs extendable by approx. 400 mm approx. 423 x 423 mm Kdsdpfxju Hp Hre Abnep -Speed sticker 80 km/h at the rear and on both sides -Load manometer to determine the axle loads including load diagram -HRM metallization (High Resistance Metallization) of the outer frame -Complete steel construction shot-blasted, then the defined visible surfaces hot-finished in metallization with ZINACOR 850 (zinc 85% - aluminium 15%)

Condition: new, empty load weight: 10,900 kg, maximum load weight: 37,100 kg, overall weight: 48,000 kg, axle configuration: 3 axles, loading space length: 9,600 mm, loading space width: 2,540 mm, loading space height: 890 mm, suspension: air, tire size: 235/75 R 17.5, color: grey, operation weight: 10,900 kg, Equipment: ABS, Gooseneck: -Gooseneck in SNT design to optimize the loading area length, length approx. 3,700 mm, with a bevel at the rear of approx. 1,000 mm x 6° -Technical fifth wheel load: 18,000 kg -For tractor units: 4 x 2 and 6 x 2 Loading area: -Loading area, length approx. 9,600 mm with a bevel at the rear of approx. 900 mm x 6° -Loading area can be raised and lowered hydraulically after the gooseneck, length approx. 3,000 mm, load capacity up to approx. 9,000 kg -Grating and sheet metal floor approx. 5 mm as additional reinforcement on the bevel of the loading area Ramps: -A pair of two-part AXS steel ramps with a length of approx. 4,675 mm and a width of approx. 900 mm -Grating floor -Hydraulically hinged ramp tips -Ramps can be moved hydraulically by approx. 235 mm outwards and approx. 365 mm inwards -Painted sand coating on the outer frame of the ramp and on the ramp tip -Flashlights on the outside of the ramp tips with switch next to the ramp controls -Ramp secured in driving position using a quick release Axles, suspension and tires: -BPW axles and suspension, 1st and 2nd axle rigid, 3rd axle with self-steering -1st Axle with traction aid -Operation via the brake pedal in the tractor unit -Technical axle load: 12,000 kg -Air suspension with lifting and lowering valve -235/75 R 17.5 -TPMS tire pressure monitoring system in accordance with ECE R 141 -TPMS tire pressure monitoring sensors mounted in all wheels including spare wheels Braking system: -WABCO EBS-E brand braking system in accordance with EU regulations Paintwork: -Semi-trailer MB 7350 Nova gray Accessories included: -Bulkhead made of steel, plug-in, approx. 400 mm high -3 kW electro-hydraulic unit for controlling the hydraulic processes, with the exception of hydraulic cable winches -Guide plate from the gooseneck for the fifth wheel plate, approx. 500 mm wide -JOST module B - static test load = 50,000 kg -Continuous grating with 5 mm sheet metal underlay as additional reinforcement -Painted sand coating -Cutouts in the outer frame of the loading area and the lifting bed for hanging control valves for the hydraulic ramps on the right of the vehicle -2" kingpin -Central lubrication system with 1 pump, brand BEKAMAX -On the gooseneck 1 pair of plug-in aluminum side walls, approx. 400 mm high, anodized -Electric cable winch, approx. 5,400 kg pulling force, with radio remote control -Wire cable approx. 24 m long, cable ø approx. 9.5 mm, including cable pressure roller -WABCO Smart Board System -4 extendable warning signs, approx. 423 x 423 mm, extendable by approx. 400 mm Kedpfx Abeuadk Njnsdp

Condition: new, empty load weight: 13,500 kg, maximum load weight: 51,500 kg, overall weight: 69,500 kg, axle configuration: > 3 axles, loading space length: 8,800 mm, loading space width: 2,540 mm, loading space height: 860 mm, suspension: air, tire size: 235/75 r17.5, color: grey, Equipment: ABS, Gooseneck: Gooseneck in SNT design for optimizing the loading area length, length approx. 3,700 mm Rear gooseneck with bevel, approx. 1,000 mm x 10° Loading area: Telescoping loading area, length approx. 8,800 mm, with rear bevel approx. 500 mm x 10° Recess in the bevel and extending into the loading area for accommodating the excavator boom foot Pneumatic locking system with tapered pin and reinforced locking positions The supply lines are protected in the extendable beam and adapt to the respective loading area length Ramps: 1 pair of two-part steel ramps, approx. 4,350 mm x 900 mm Hydraulically folding ramp ends Ramps can be individually hydraulically moved outwards by approx. 235 mm and inwards by approx. 215 mm Axles and Suspension: BPW axles and suspension, two axles fixed, two axles with trailing arm steering Electromagnetic parking brake activated via reverse gear and manually Air suspension with raising and lowering valve Axle tool Tires: 235/75 R17.5 3PMSF, dual tires Load index: 143/141J (144/144F) Kodpfx Aok Ahugjbnjdp Braking System: Braking system from WABCO, EBS-E according to EU regulations Lighting System: 24-volt lighting system in "ASPÖCK-NORDIK full LED" Metallization: Standard HRM metallization of the outer frame Complete steel construction shot-blasted, then the defined visible surfaces hot-dip metallized with ZINACOR 850 (Zinc 85% - Aluminum 15%) Steel Construction: Steel qualities: S355J2+N/S355MC (yield strength 355 MPa) S690QL/S700MC (yield strength 690 MPa) Welders certified according to DIN-EN 287-1 Welding process MAG according to EN ISO 4063 Shielding gas M21 according to EN ISO 14175 Included Accessories: Steel front wall, pluggable, height approx. 400 mm ASPÖCK-UNIBOX on the connection strip at the front with sockets 24N, 24S & 15-pin 24N connection according to ISO-1185, 24S connection according to ISO-3731, 15-pin connection according to ISO-12098 Round NATO socket on the connection strip at the front Cable for supplying the electro-hydraulic unit and/or the electric winch (35 mm2, 3.5 m long) between the semi-trailer and the drawbar trailer with plug (NATO-NATO) 3 kW electro-hydraulic unit for controlling the hydraulic operations, with the exception of hydraulic winches 1 spare wheel with mounting adapter Outer beam of the gooseneck with mounting holes for screwable lashing rings, the first hole approx. 200 mm from the front, then approx. every 400 mm 2 pairs of screwable lashing rings included One mounting hole in the rear upper area of the outer beam of the gooseneck for a screwable lashing ring 1 pair of screwable lashing rings Approx. 40 mm thick hardwood flooring above the gooseneck On the gooseneck, 1 pair of pluggable aluminum side panels, approx. 400 mm high, anodized On the gooseneck, one pluggable aluminum rear panel, approx. 400 mm high, anodized 2" kingpin Guide plate of the gooseneck for the saddle plate, approx. 500 mm wide 4 support wedges with holder Mounting for aluminum approach ramps Mechanical saddle supports with 2-speed gearbox and crank On the loading area, a continuous and interrupted between the axles hardwood flooring, approx. 50 mm thick Locking of the loading area with tapered welded locking profiles every 250 mm incl. pre-tensioning plate Elongated holes for hanging and adjustable bridging elements on the loading area at the front 1 intermediate table with recessed loading area, approx. 300 mm wide for the extension tube with large cross-section with sheet metal covering At the front and

Condition: new, empty load weight: 17,500 kg, maximum load weight: 43,500 kg, overall weight: 61,000 kg, axle configuration: 3 axles, loading space length: 7,550 mm, loading space width: 2,750 mm, loading space height: 400 mm, tire size: 245/70 R 17.5, color: grey, Equipment: ABS, Gooseneck: -Gooseneck in SNT design to optimize the platform length, length approx. 3,750 mm -Gooseneck can be hydraulically raised/lowered and extended/retracted -For semi-trailer tractors: 6x4 or 8x4 Drop deck: -Drop deck with external beams in an extendable design, "SUPER LOW" design, length approx. 7,550 mm -Drop deck with a fixed hardwood floor approx. 40 mm thick and mechanical locking -The supply lines are protected in the extendable beams and automatically adjust to the respective drop deck length Rear chassis: -Rear chassis with a closed outer frame, non-slip steel plate surface, and continuous prism excavator well approx. 1,450/900 x 505 mm, open at the rear -2 pairs of pocket slots for plug-in cross members 100 x 50 mm in the outer frame Axles and tires: -"PENDEL-AXLE", all axles hydromechanically steered -Hose rupture valve on the axle equalization cylinder with automatic RESET function -Hydraulic cylinder with shut-off valves and quick-release coupling to secure in the raised position -Technical axle load: 12,000 kg -Hydraulic axle equalization -Tires 245/70 R 17.5 / 3PMSF Included accessories: -Preparation for attaching screw-on container positioning for 1x 20ft or 1x 40ft container on the outer beams -2" kingpin -A galvanized steel front bulkhead approx. 400 mm high -A spare wheel with holder -Yellow-red air couplings on the galvanized connection strip at the front -4 wheel chocks -Rear steering from the front and rear, operable via cable remote control with push buttons, with single-axle control -Hydraulic connections from the gooseneck to the drop deck with multi-coupling instead of screw coupling -Electro-hydraulic power unit -White reflector tape according to EU regulations on the sides, on the extension and red at the rear -2 wooden blocks 500x250x200 mm Kdodpfx Aeh Hm Thobnep -European reflector signs (red-yellow) at the rear of the trailer -On the gooseneck and on the rear plate, one holder each on the left and right for the warning signs including socket -Central lubrication system with 2 BEKAMAX (Pico) pumps with normal grease NLGI-2 -Load gauge to determine the axle loads including load diagram -On the gooseneck, aluminum side and rear panels that can be plugged in, approx. 2,000 x 400 mm -The rear galvanized plug-in cross members are removable (length of the superstructure approx. 2,120 mm) -On the gooseneck, a separate air connection with air gun -Duomatik air coupling from gooseneck to drop deck -Gooseneck in the rear upper area closed with a removable cover -1 pair of steel ramps to bridge the lifting hooks of the drop deck -Four warning signs, extendable by approx. 400 mm, approx. 423 x 423 mm -Radio remote control for rear steering in addition to the cable remote control, with indicator lights on the receiver for single-axle control -6 pairs of threaded blocks between the lashing rings under the top chord on the outer beam for mounting screw-on RUD rings VLBG-4 -7 pairs of pocket slots for plug-in cross members 100 x 50 mm in the outer frame of the loading platform -Foldable widening extensions, approx. 230 mm each side -A painted sand layer on the loading platform as an anti-slip coating -Bucket stick recess of the rear chassis closed at the front and rear with a plug-in plate -HRM metallization (High Resistance Metallization) of the outer frame -Complete steel construction blasted with shot, then the defined visible surfaces hot-dip galvanized with ZINACOR 850 (Zinc 85% - Aluminum 15%)

Condition: new, empty load weight: 13,250 kg, maximum load weight: 47,550 kg, overall weight: 60,800 kg, axle configuration: > 3 axles, suspension: air, tire size: 245/70 r17.5, color: grey, Equipment: ABS, Gooseneck: Gooseneck with rear bevel of approx. 750 mm x 10°. 3 pairs of lashing rings Hardwood decking 30 mm thick Loading platform in extendable version: Loading area in extendable version with rear bevel of approx. 1,000 mm x 8° 5 pairs of lashing rings can be folded outwards 3 pairs of lashing rings can be folded outwards 1 pair of lashing rings lying in the front of the cargo bed Cut-outs in the outer frame of the cargo bed for attaching lashing straps Hardwood flooring approx. 48 mm thick, checker plate flooring over the axles Two-part steel ramps: A pair of galvanized two-part steel ramps approx. 2,750 + 1,400 x 800 mm with approx. 48 mm thick hardwood decking. Ramp with hydraulically folding and unfolding ramp sections, hydraulic lifting gear and hydraulically movable. Maximum load per pair: 40,000 kg Seat posts: JOST fifth wheels (mechanical) with 2-speed gearbox for 24t lifting load (50t test load) Axles and tires: BPW axles and suspension, 1st axle rigid, all other axles hydro-mechanically forced steered Technical axle load: 12,000 kg Air suspension with lifting and lowering valve Axle tool Kedjl Uxdkepfx Abnedp Tires 245/70 R 17.5 Brake system: Brake system in accordance with EU regulations with EBS-E (4S3M) without connecting lines to the tractor unit Steel construction: Steel construction made of high-strength fine-grained steels Steel grades: S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa) Coating: First-class and durable corrosion protection of the standard shot-peened welded frame guaranteed by a 2-component (2K) zinc dust primer A high-quality 2-component (2K) top coat in a single color in nova grey Rear section metallized and painted in RAL 9010 (pure white) No metallic paint finish possible Electrical system: Electrical system in accordance with EU regulations, 24 volt lighting ASPÖCK-NORDIK (ASS3) ASPÖCK-UNIBOX on the front connection strip with 24N, 24S & 15-pin sockets Connection according to ISO 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Accessories included: 2" kingpin One galvanized steel end wall approx. 400 mm high Yellow-red air couplings on the galvanized connection strip at the front 4 restraining shoes with holder on the bulkhead One spare wheel with holder in front of the bulkhead Electro-hydraulic unit Re-steering from the front and rear by means of cable remote control operated via pushbuttons with tracking control of the axles Mounting in the rear area of the gooseneck for ALU docking lights European reflector plates (red/yellow) at the rear of the trailer White reflective tape in accordance with EU regulations on the side, on the extension and at the rear Red On the gooseneck and on the ramps on the left and right, a holder for the warning signs including a socket A bracket for a rotating beacon at the rear of the trailer Galvanized folding supports under the sloping loading area Operating valves for the ramps fitted on the right-hand side of the trailer Cover plates to bridge the gap between the ramps and the cargo bed A mud flap at the rear of the trailer Manual and description on USB stick BEKAMAX (Pico) central lubrication system with NLGI-2 standard grease and removable protection around the pump ALU drop sides and rear wall can be plugged onto the gooseneck approx. 2,440 x 400 mm The rear galvanized stanchions are removable Length of the body approx. 2,560 mm One tool box INOX 1,350 x 400 x 400 on the gooseneck Box covered oil filler plug 4 pairs of WADER container pockets in t