Used Faymonville Lowbed Semitrailers for sale (220)

Condition: used, maximum load weight: 42,700 kg, overall weight: 58,600 kg, axle configuration: 3 axles, first registration: 07/2013, Equipment: ABS, Vehicle identification number: YAFTL313000014137 First registered: July 18, 2013 DE HU due Own weight: 15,900 kg Total length: 16,700 mm Gooseneck 3,700 mm Steering radius of kingpin to the rear approx. 2,700 mm Kingpin standard 3.5 inches - fifth wheel height: 1,320 - 1,350 mm Low bed length: 8,500 mm - Loading height: approx. 500 mm TELESCOPIC by 4,250 mm Chassis frame: 4,500 mm - Loading height: approx. 900 mm Suspension travel (with air suspension) approx.: -80/+160 mm Excavator trough - Dipper stick trough Hydraulic support feet Fjdpfx Aasrtlxhe Reft Fifth wheel load technically up to 25,000 kg Axle loads 3 x 11,200 kg Axle spacing: 1,360 mm SAF axles with drum brakes 3 x hydraulically forced-steered axles with RADIO + cable remote control Tires: 235/75 R 17.5

Condition: new, empty load weight: 12,300 kg, maximum load weight: 37,200 kg, overall weight: 49,500 kg, axle configuration: 3 axles, loading space length: 9,300 mm, loading space width: 2,480 mm, loading space height: 860 mm, suspension: air, tire size: 235/75 R17.5, color: grey, Equipment: ABS, Gooseneck: -Gooseneck with rear bevel of approx. 750 mm x 10° -Hardwood covering 30 mm thick Two-piece steel ramps: -A pair of galvanized two-part steel ramps approx. 3,185x1,420x1,250 mm with grating decking -Ramp with hydraulically folding and unfolding ramp sections, hydraulic lifting gear Gooseneck: -Gooseneck with rear bevel of approx. 750 mm x 10° -3 pairs of lashing rings -Hardwood decking 30 mm thick Two-part steel ramps: -One pair of galvanized two-part steel ramps approx. 3,185x1,420x1,250 mm with grating covering -Ramp with hydraulically folding and unfolding ramp sections, hydraulic lifting gear -Maximum load per pair: 30,000 kg Loading area: -Loading surface with rear slope of approx. 1,000 mm x 8° -Hardwood flooring approx. 48 mm thick, checker plate flooring over the axles Axles and tires: -BPW axles and suspension, two axles rigid, one axle self-steering -Air suspension with lifting and lowering valve The self-steering axles with electro-magnetic reverse lock can be activated via reverse gear or manually -235/75 R17.5 3PMSF tires Accessories included: -1 Spare wheel with holder -TPMS tire pressure monitoring system according to ECE R 141 -2" kingpin -Galvanized steel bulkhead -Yellow-red air couplings on the galvanized front connecting strip -4 restraining shoes with holder on the bulkhead -Mounting in the rear area of the gooseneck for ALU docking ramps -3 height aluminum boards -Galvanized folding supports under the bevel of the cargo bed Height-adjustable tarpaulin superstructure (3,960 mm) Fsdpotvfkfefx Aa Rjft -Galvanized bulkhead with a tensioning mechanism for the sliding curtain -Height-adjustable by approx. 400 mm -"EDSCHA" brand roof can be moved forwards on ALU roof rail profiles bolted to the front and rear wall -3 pairs of sliding stanchions in the loading area -The body can be hydraulically widened at the rear to the left and right by approx. 750 mm -Sliding roof with pivoting portal support -Sliding tarpaulin with 700 mm reserve in length, with tension belts at approx. 600 mm intervals -Height top edge of body approx. 3,960 mm -Driving with the sliding tarpaulin open is not permitted and will damage the tarpaulin -Cover plates to bridge the free space between ramps and loading area -Electric hydraulic unit at the rear, under the cargo bed -On the gooseneck and on the ramps on the left and right, one bracket each for the warning signs including socket -Control valves for the ramps mounted on the right-hand side of the trailer -6 pairs of stanchion pockets for 100 x 50 mm stanchions in the outer frame of the cargo bed -Lift axle on the front axle -Grating in the bevel of the loading area C40/4 (point load 3.4 tons on an area of 20 x 20 cm) -One INOX toolbox 565 x 290 x 810 mm in the direction of travel on the right between the axles -A layer of sand painted onto the chequer plates on the gooseneck and on the loading area to prevent slipping -BEKAMAX (Pico) central lubrication system with NLGI-2 standard grease and removable protection around the pump -Four warning panels approx. 423 x 423 mm, extendable by approx. 400 mm, with a position light -Load manometer for determining the axle loads including load diagram -HRM metallization (High Resistance Metallization) of the outer frame -Complete steel construction shot-blasted, then the defined visible surfaces hot-finished in metallization with ZINACOR 850 (zinc 85% - aluminium 15%)

Condition: excellent (used), axle configuration: 2 axles, first registration: 02/2022, loading space length: 7,550 mm, loading space width: 2,540 mm, total length: 11,200 mm, total width: 2,540 mm, suspension: air, tire size: 245/70/17.5, color: red, Year of construction: 2022, Equipment: ABS, = Additional Options and Accessories = - Air suspension Fjdpfewffibex Aa Rsft = Further Information = Axle configuration Tire size: 245/70/17.5 Axle manufacturer: BPW ECO PLUS Brakes: Drum brakes Suspension: Air suspension Rear axle 1: Twin tires; Max. axle load: 12,000 kg Rear axle 2: Twin tires; Max. axle load: 12,000 kg; Steering axle Weights Unladen weight: 8,250 kg Payload: 40,750 kg Gross vehicle weight (GVW): 49,000 kg Functional Features Loading platform height: 85 cm Extendable body: Yes Condition Technical condition: Very good Optical condition: Very good FAYMONVILLE F-S42-1BBA 2-AXLE LOWBED TRAILER 2x axles with air suspension 2nd axle is steering 12,000 kg technically permitted maximum axle weight Technically permitted total weight 49,000 kg WABCO EBS-E system Tire size 245/70 R17.5 Extendable loading platform Loading platform length 755 cm + extendable by 500 cm up to 1,255 cm Platform width 254 cm Platform height approx. 85 cm Coupling height approx. 120 cm Lashing eyes and round pockets Warning boards front and rear

Condition: used, maximum load weight: 37,535 kg, overall weight: 48,000 kg, axle configuration: 3 axles, first registration: 08/2024, next inspection (TÜV): 08/2026, total width: 2,540 mm, Equipment: ABS, You can find our entire vehicle inventory, including immediately and soon-available vehicles, on our website. The following is an excerpt from the equipment specification. Full equipment details available on request. Loading Platform: * Extendable loading platform with pneumatically operated locking mechanism * 7 pairs of fold-out lashing rings (LC 5,000 daN) * 3 pairs of fold-out lashing rings (LC 10,000 daN) * Cut-outs in the outer frame of the loading platform for attaching tension straps (LC 2,000 daN) Landing Legs: * JOST landing legs (mechanical) with 2-speed gearbox for approx. 24 t lifting capacity (approx. 50 t test load) Axles: Fedpfx Aasxgk U Ns Roft * BPW axles, air-suspended, with disc brakes (approx. 430 mm), fitted with lift/lower function. Technical axle load: 10,000 kg each (ET0) * Self-steering axle with electromagnetic reverse lock, activated via reverse gear or manually * Axle tool Tyres: * Tyres 385/65 R 22.5 Brake System: * Brake system compliant with EU regulations with EBS-E (2S2M), without connecting lines to tractor unit Steel Construction: * Steel construction made of high-strength fine-grained steels * Steel grades: S355J2+N/S355MC (yield strength 355 MPa), S690QL/S700MC (yield strength 690 MPa) Paintwork: * Premium and durable corrosion protection of the standard shot-blasted welded frame by a two-component (2K) zinc dust primer * High-quality single-color topcoat (2K) in RAL 3002 carmine red * Rims in silver * Rear section metallised and painted in RAL 9010 (pure white) Including the following additional equipment: * Yellow-red air couplings on galvanised front connector bar * 4 wheel chocks with holders * 2" king pin * Yellow reflective tape compliant with EU-standard on sides, extension and trailer rear * European reflector boards (red-yellow) on rear of trailer * Loading platform with approx. 30 mm thick wooden floor encased in Omega profiles * 10 pairs of stake pockets for insertable stanchions approx. 100 x 50 mm in the outer frame of the loading platform * Storage for up to 9 pairs of insertable stanchions approx. 100 x 50 mm bolted to the inside of the front wall * 1 spare wheel holder under the loading platform on the left in the driving direction, without spare wheel * One mudflap at the rear of the trailer * Manual and documentation on USB stick * Bracket for rotating beacon at the rear of the trailer * On gooseneck and rear panel, left and right, one holder each for warning signs, including socket * Speed stickers 80 km/h, rear and both sides * Load gauge for axle load determination including load chart * Galvanised steel front wall (EN12642-XL), approx. 1,600 mm high * 6 pairs of WADER container pockets on loading platform, for 1x 20' container, 2x 20' containers or 1x 40' container flush with the rear * INOX toolbox, approx. 600 x 350 x 600 mm, under the platform on the left in the driving direction * 4 pairs of longitudinal stake pocket rails for 80 x 50 mm insertable stanchions mounted on the loading platform * Lift axle on the front axle with control via TEBS E depending on current axle load and loading condition * 2 LED reversing lights mounted on rear panel * HRM metallisation (High Resistance Metallisation)

Condition: used, maximum load weight: 42,700 kg, overall weight: 58,600 kg, axle configuration: 3 axles, first registration: 07/2013, Equipment: ABS, Vehicle identification number: YAFTL313000014136 First registered: July 18, 2013 DE HU due Own weight: 15,900 kg Total length: 16,700 mm Gooseneck 3,700 mm Steering radius of kingpin to the rear approx. 2,700 mm Kingpin standard 3.5 inches - fifth wheel height: 1,320 - 1,350 mm Ffedpfjr Dplmox Aa Rot Low bed length: 8,500 mm - Loading height: approx. 500 mm TELESCOPIC by 4,250 mm Chassis frame: 4,500 mm - Loading height: approx. 900 mm Suspension travel (with air suspension) approx.: -80/+160 mm Excavator trough - Dipper stick trough Hydraulic support feet Fifth wheel load technically up to 25,000 kg Axle loads 3 x 11,200 kg Axle spacing: 1,360 mm SAF axles with drum brakes 3 x hydraulically forced-steered axles with RADIO + cable remote control Tires: 235/75 R 17.5

Condition: new, empty load weight: 9,500 kg, maximum load weight: 35,500 kg, overall weight: 45,000 kg, axle configuration: 3 axles, loading space length: 13,500 mm, loading space width: 2,540 mm, suspension: air, tire size: 435/50 R 19.5, color: grey, operation weight: 9,500 kg, Equipment: ABS, Extendable loading area: Loading area with hardwood planks with rear slope of approx. 1,000 mm x 8°    1 pair of permanently installed wheel recesses, approx. 1,610 x 970 x 400 mm     2 pairs of lashing rings (LC 5,000 daN)    1 pair of lashing rings (LC 10,000 daN)    6 pairs of lashing rings that can be folded outwards (LC 5,000 daN)    2 pairs of lashing rings that can be folded outwards (LC 10,000 daN)    Cut-outs in the outer frame of the loading area for attaching tensioning straps. (LC 2,000 daN)     Braking system:    Braking system in accordance with EU regulations with EBS-E (2S2M) Painting:    First-class and long-lasting corrosion protection of the standard shot-blasted welded frame guaranteed by a 2-component (2K) zinc dust primer     A high-quality 2-component (2K) top coat in a single color in Nova gray Rear section metallized and painted in RAL 9010 (pure white)     No metallic painting possible     Seatposts:     JOST seatposts (mechanical) with 2-speed gearbox for 24t lifting load (50t test load)     Steel construction:     Steel construction made of high-strength fine-grain steels     Steel qualities:     S355J2+N/S355MC (yield point 355MPa)    S690QL/S700MC (yield point 690MPa)    Electrical system:    Electrical system in accordance with EU regulations, lighting 24 volts    Sockets 24N, 24S & 15-pin    Axles and tires:    BPW axles, air-suspended, with disc brakes (377 mm), with lifting/lowering function    The self-steering axles with electromagnetic reversing lock can be activated via reverse gear or manually    Axle tool    Tires 435/50 R 19.5    Ffodek Eammopfx Aa Rst Accessories included:    Yellow-red air couplings on the galvanized connection strip at the front    4 wheel chocks with brackets    2" kingpins    A galvanized steel bulkhead approx. 1600 mm high. EN12642-XL    White reflective tape in accordance with EU regulations on the side, on the extension and at the rear Red    Loading area with strong hardwood floor    9 pairs of stake pockets for 100 x 50 mm stakes in the outer frame of the loading area    1 spare wheel holder under the loading area on the right in the direction of travel    Galvanized folding supports under the slope of the loading area    Sliding hanging rails for aluminum loading ramps at the rear of the vehicle    European reflector signs (red-yellow) at the rear of the trailer    A mud flap at the rear of the trailer    A bracket for a rotating beacon at the rear of the trailer    On the gooseneck and on the rear panel on the left and right, a bracket for the warning signs including a socket    A tool box HDPE 620x360x610 under the loading area on the left in the direction of travel    4 pairs of WADER container pockets in the loading area, for 1x 20ft container or 1 x 40ft container, an additional locking point is provided in the extension for a 45ft container 3 pairs of stake pocket strips, mounted transversely in the loading area, for 100 x 50 mm stakes Lift axle on the front axle with control by TEBS E depending on the current axle load and the current loading condition Speed sticker 80 km/h at the rear and on both sides Four warning signs extendable by approx. 400 mm, approx. 423 x 423 mm with an LED position light. A holder for a rotating beacon on the warning signs Load gauge for determining the axle loads including load diagram HRM metallization (high resistance metallization) of the outer frame Complete steel construction shot blasted, then the defined visible areas in metallization

Condition: excellent (used), axle configuration: 2 axles, first registration: 06/2015, loading space length: 6,100 mm, loading space width: 2,540 mm, suspension: air, tire size: 235/75/17.5, color: red, Year of construction: 2015, Equipment: ABS, = Additional Options and Accessories = - Air suspension = Further Information = Axle configuration Tyre size: 235/75/17.5 Axle brand: SAF Brakes: Drum brakes Suspension: Air suspension Rear axle 1: Twin tires; Max. axle load: 10,000 kg; Steered Rear axle 2: Twin tires; Max. axle load: 10,000 kg; Steered Weights Unladen weight: 9,900 kg Payload: 35,100 kg Gross vehicle weight: 45,000 kg Functional Loading platform height: 55 cm Extendable superstructure: Yes Condition Technical condition: very good Visual condition: very good FAYMONVILLE MEGAMAX F-S42-1ACA 2-AXLE LOWBED TRAILER SAF AXLES AIR SUSPENSION 1ST AND 2ND AXLES ARE STEERABLE LOAD CAPACITY 35.1 TONNES WABCO EBS-E LOADING PLATFORM LENGTH 610 CM + EXTENDABLE BY 250 CM PLATFORM WIDTH 254 CM Ffjdjw Dqvwjpfx Aa Rot PLATFORM THICKNESS 20 CM LOADING PLATFORM HEIGHT +/- 55 CM EXCAVATOR ARM WELL L=315 CM, W=75 CM, DEPTH=28 CM REAR SIDE-MARKER LIGHTS LOAD PLATFORM ANCHOR POINTS TOOLBOX RETURN ROLLER 4 X WHEEL CHOCKS

Condition: used, maximum load weight: 38,080 kg, overall weight: 48,000 kg, axle configuration: 3 axles, first registration: 02/2025, next inspection (TÜV): 02/2026, total width: 2,540 mm, Equipment: ABS, You can find our complete inventory of immediately and short-term available vehicles on our website. Excerpt from the equipment list. Full specifications available upon request. Loading Platform: * Extending loading platform with pneumatically operated locking mechanism * Loading platform with approx. 30 mm thick wooden floor framed in omega profiles * 7 pairs of folding external lashing rings (LC 5,000 daN) * 3 pairs of folding external lashing rings (LC 10,000 daN) * Cut-outs in the outer frame of the platform for attaching tension belts (LC 2,000 daN) Landing Legs: * JOST landing legs (mechanical) with 2-speed gearbox, approx. 24 t lifting capacity (approx. 50 t test load) Axles: * BPW axles and suspension * All axles hydro-mechanically forced-steered * Equipped with disc brakes * Technical axle load: 10,000 kg each (ET 0) * Air suspension with lift and lower valve * Axle tools Tyres: * Tyres: 385/65 R 22.5 Braking System: * Braking system according to EU regulations with EBS-E (2S2M), without connecting lines to the tractor Warning Signs: * Mountings on the gooseneck and rear panel left and right for warning signs, including socket Electrical System: * Electrical system according to EU regulations * Lighting 24 Volt ASPÖCK-NORDIK (ASS3) * ASPÖCK-UNIBOX on the front connection strip with sockets 24N, 24S & 15-pin, connection according to ISO 24N ISO-1185, 24S ISO-3731, 15-pin ISO-12098 Steel Construction: * Steel structure made of high-strength fine-grained steels * Steel grades S355J2+N/S355MC (yield strength 355 MPa), S690QL/S700MC (yield strength 690 MPa) Paintwork: * First-class, durable corrosion protection for the standard grit-blasted welded frame, guaranteed by a two-component zinc dust primer * High-quality, single-colour two-component topcoat in RAL 3002 carmine red * Rims in silver, add-on parts as per manufacturer's choice * Rear section metallized and painted in RAL 9010 pure white Included Accessories: Ffsdpsxf Sifofx Aa Rot * 2-inch kingpin * 4 wheel chocks with brackets on the front wall * Remote steering, front and rear, cable-operated by push buttons, with single-track control of the axles (without installation in the tractor) * Manual and description on USB stick * Electro-hydraulic unit * Galvanized connection strip at front, yellow-red air couplings * Yellow reflective tape according to EU regulations on the sides, extension and rear of the trailer * European reflective panels (red-yellow) on the rear of the trailer * One mud flap at the rear of the trailer * Mounting for rotating beacon at the rear of the trailer * 10 pairs of pocket sockets for plug-in stanchions 100 x 50 mm in the outer frame of the loading platform * 1 spare wheel holder under the platform on the right-hand side * Speed stickers 80 km/h on the rear and on both sides * Load manometer for determining axle loads including load chart * Galvanized steel front wall (EN12642-XL), approx. 1,600 mm high * 6 pairs of WADER container pockets in the platform for: 1 x 20' container, 2 x 20' container or 1 x 40' container; an additional locking point is provided in the extension for a 45' container * 4 pairs of transverse stanchion strip pockets for plug-in stanchions approx. 100 x 50 mm * Storage for plug-in stanchions on the inside of the front wall * Access ladder installed on both left and right side in the direction of travel * One INOX toolbox, approx. 1,200 x 460 x 550 mm, mounted under the loading platform at the front left in the direction of travel * One add

Condition: new, empty load weight: 11,300 kg, maximum load weight: 36,700 kg, overall weight: 48,000 kg, axle configuration: 3 axles, loading space length: 13,600 mm, loading space width: 2,540 mm, loading space height: 1,250 mm, suspension: air, tire size: 385/65 r 22,5, color: grey-black, Equipment: ABS, Cargo bed: Loading platform in extendable design with pneumatically operated locking mechanism There is an approx. 250 mm wide fixed intermediate table on the middle carrier 8 pairs of lashing rings can be folded outwards (LC 5,000 daN) 3 pairs of lashing rings can be folded outwards (LC 10,000 daN) Cut-outs in the outer frame of the cargo bed for attaching lashing straps (LC 2,000 daN) Axles and tires: BPW axles and suspension, all axles with hydro-mechanical forced steering Disc brakes, technical axle load: 10,000 kg Air suspension with lifting and lowering valve Axle tool 6-wheel tires 385/65 R 22.5 Brake system: Brake system in accordance with EU regulations with EBS-E (2S2M) Seat posts: JOST seat posts (mechanical) with 2-speed gearbox for 24 tons lifting load (50 tons test load) Steel construction: Steel construction made of high-strength fine-grained steels Fodpfx Aashlz She Reft Steel grades: S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa) Electrical system: Electrical system in accordance with EU regulations, 24 volt lighting ASPÖCK-NORDIK (ASS3) ASPÖCK-UNIBOX on the front connection strip with 24N, 24S & 15-pin sockets Connection according to ISO: 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Paint finish: First-class and durable corrosion protection of the standard shot-peened welded frame guaranteed by a 2-component (2K) zinc dust primer A high-quality 2-component (2K) top coat in a single color in nova grey Rear section metallized and painted in RAL 9010 (pure white) No metallic paint finish possible Accessories included: A bracket for the warning signs on the gooseneck and on the rear panel on the left and right, including socket Re-steering can be operated from the front and rear using a cable remote control via pushbuttons, with toe-in control for the axles Electro-hydraulic unit 4 wheel chocks with holder on the bulkhead 2" kingpin One galvanized steel bulkhead approx. 2,200 mm high Yellow-red air couplings on the galvanized connection strip at the front White reflector tape in accordance with EU regulations on the side, on the pull-out and at the rear Red European reflector plates (red/yellow) at the rear of the trailer A mud flap at the rear of the trailer Manual and description A bracket for a rotating beacon at the rear of the trailer Loading area with approx. 30 mm thick wooden floor edged in omega profiles 10 pairs of stanchion pockets for 100 x 50 mm stanchions in the outer frame of the cargo bed 1 spare wheel holder under the cargo bed on the right in the direction of travel 6 pairs of WADER container pockets in the cargo bed, for 1x 20ft container, 2x 20ft containers or 1x 40ft container, an additional locking point is provided in the pull-out for a 45ft container 5 pairs of stanchion pocket rails, mounted transversely in the loading area, for 100 x 50 mm stanchions One galvanized bracket transversely under the cargo bed (2,390 x 720 x 400 mm) Access ladder mounted on the right in the direction of travel One HDPE 1,200 x 500 x 480 mm toolbox at the front under the cargo bed on the left in the direction of travel Lift axle on the front axle with control by TEBS E depending on the current axle load and the current load status Central lubrication system with 2 BEKAMAX (Pico) pumps with NLGI-2 standard grease and removable protection around the pump Red/white reflective tape in the load platform extension A layer of sand painted onto the central beam to prevent slipping Radio remote control for the steer

Condition: new, empty load weight: 11,000 kg, maximum load weight: 38,500 kg, overall weight: 49,500 kg, axle configuration: 3 axles, loading space length: 9,300 mm, loading space width: 2,540 mm, loading space height: 860 mm, suspension: air, tire size: 235/75 R 17,5, color: grey, Gooseneck: -Gooseneck with rear bevel of approx. 750 mm x 10° -3 pairs of lashing rings (LC 5,000 daN) -Hardwood decking 30 mm thick Fodpfx Aaoup U Hzs Reft Loading area: -telescopic loading area with rear slope approx. 1,000 mm x 8° -1 pair of fixed wheel recesses in front of the axles approx. 2,850 x 970 x 400 mm -Wheel recesses with square climbing strips 15 x 15 mm and widenings in the lower area -A pair of fixed wheel recesses with cover between the 1st and 2nd axle, approx. 1,610 x 970 x 400 mm -Recess in the chamfer and protruding into the loading area to accommodate the excavator dipper stick, approx. 2,900 x 750 x 210/290 mm -1 pair of lashing rings lying in the front of the cargo bed (LC 10,000 daN) -5 pairs of lashing rings foldable outwards (LC 5,000 daN) -2 pairs of lashing rings can be folded outwards (LC 10,000 daN) Cut-outs in the outer frame of the cargo bed for attaching lashing straps. (LC 2,000 daN) -incl. 3 removable galvanized covers over the wheel recesses - max. point load 3.5 to / pc. Hydr. two-part steel ramps: -One pair of galvanized two-part steel ramps approx. 2,750 + 1,400 x 800 mm with approx. 48 mm thick hardwood decking -Ramp with hydraulically folding and unfolding ramp sections, hydraulic lifting gear and hydraulically movable Axles and tires: -PW axles and suspension, 2 axles rigid, 1 axle self-steering -Technical axle load: 12,000 kg -Electromagnetic reverse lock via reverse gear and can be activated manually -Air suspension with lifting and lowering valve -axle tool -235/75 R 17.5 tires Accessories included: -2" kingpin -One galvanized steel bulkhead approx. 400 mm high -One spare wheel with holder in front of the bulkhead -Yellow-red air couplings on the galvanized connection strip at the front -4 wheel chocks with holder on the bulkhead -Mounting in the rear area of the gooseneck for ALU docking lights -Galvanized extensions, extendable by approx. 230 mm per side -Galvanized folding supports under the bevel of the cargo bed -One bracket for a rotating beacon at the rear of the trailer -White reflector tape in accordance with EU regulations on the sides, on the pull-out and red at the rear -One bracket for the warning signs including socket on the gooseneck and on the left and right rear plate -One mud flap at the rear of the trailer -European reflector plates (red/yellow) at the rear of the trailer -ALU drop sides and rear wall pluggable onto the gooseneck approx. 2,440 x 400 mm -The rear galvanized stanchions are removable (length of the body approx. 2,560 mm) -2 pairs of WADER container pockets in the loading area for a 20ft or 30ft container -3 pairs of stanchion pockets for 100 x 50 mm stanchions in the outer frame of the cargo bed -One removable galvanized intermediate table with 1 pair of WADER container pockets -Square climbing rails 20 x 20 mm every 200 mm on the outer frame of the loading area slope -Four warning signs approx. 423 x 423 mm, extendable by approx. 400 mm, with a position light -One bracket for rotating beacon on the warning signs -Speed sticker 80 km/h at the rear and on both sides -Load manometer for determining the axle loads including load diagram -HRM metallization (High Resistance Metallization) of the outer frame. -Complete steel construction shot-blasted, then the defined visible surfaces hot-finished in metallization with ZINACOR 850 (zinc 85% - aluminium 15%) Optionally available: -A toolbox on the gooseneck

Condition: new, empty load weight: 10,900 kg, maximum load weight: 37,100 kg, overall weight: 48,000 kg, axle configuration: 3 axles, loading space length: 9,600 mm, loading space width: 2,540 mm, loading space height: 890 mm, suspension: air, tire size: 235/75 R 17.5, color: grey, operation weight: 10,900 kg, Equipment: ABS, Gooseneck: -Gooseneck in SNT design to optimize the loading area length, length approx. 3,700 mm, with a bevel at the rear of approx. 1,000 mm x 6° -Technical fifth wheel load: 18,000 kg -For tractor units: 4 x 2 and 6 x 2 Loading area: -Loading area, length approx. 9,600 mm with a bevel at the rear of approx. 900 mm x 6° -Loading area can be raised and lowered hydraulically after the gooseneck, length approx. 3,000 mm, load capacity up to approx. 9,000 kg -Grating and sheet metal floor approx. 5 mm as additional reinforcement on the bevel of the loading area Ramps: -A pair of two-part AXS steel ramps with a length of approx. 4,675 mm and a width of approx. 900 mm -Grating floor -Hydraulically hinged ramp tips -Ramps can be moved hydraulically by approx. 235 mm outwards and approx. 365 mm inwards -Painted sand coating on the outer frame of the ramp and on the ramp tip -Flashlights on the outside of the ramp tips with switch next to the ramp controls -Ramp secured in driving position using a quick release Axles, suspension and tires: -BPW axles and suspension, 1st and 2nd axle rigid, 3rd axle with self-steering -1st Axle with traction aid -Operation via the brake pedal in the tractor unit -Technical axle load: 12,000 kg -Air suspension with lifting and lowering valve -235/75 R 17.5 -TPMS tire pressure monitoring system in accordance with ECE R 141 -TPMS tire pressure monitoring sensors mounted in all wheels including spare wheels Braking system: -WABCO EBS-E brand braking system in accordance with EU regulations Paintwork: -Semi-trailer MB 7350 Nova gray Accessories included: -Bulkhead made of steel, plug-in, approx. 400 mm high -3 kW electro-hydraulic unit for controlling the hydraulic processes, with the exception of hydraulic cable winches -Guide plate from the gooseneck for the fifth wheel plate, approx. 500 mm wide -JOST module B - static test load = 50,000 kg -Continuous grating with 5 mm sheet metal underlay as additional reinforcement -Painted sand coating -Cutouts in the outer frame of the loading area and the lifting bed for hanging control valves for the hydraulic ramps on the right of the vehicle -2" kingpin -Central lubrication system with 1 pump, brand BEKAMAX -On the gooseneck 1 pair of plug-in aluminum side walls, approx. 400 mm high, anodized -Electric cable winch, approx. 5,400 kg pulling force, with radio remote control -Wire cable approx. 24 m long, cable ø approx. 9.5 mm, including cable pressure roller Fedpfjuadk Njx Aa Rjft -WABCO Smart Board System -4 extendable warning signs, approx. 423 x 423 mm, extendable by approx. 400 mm

Condition: new, empty load weight: 29,600 kg, maximum load weight: 72,400 kg, overall weight: 102,000 kg, axle configuration: > 3 axles, loading space length: 6,650 mm, loading space width: 2,840 mm, loading space height: 550 mm, tire size: 285/70 R19.5, color: grey, operation weight: 29,600 kg, Equipment: ABS, Gooseneck: -Hydraulic gooseneck Raisable/lowerable and removable -Length approx. 3,650 mm -For tractor units: 6 x 4 or 8 x 4 2-axle chassis at the front: -Hook attachments at the front and rear -Chassis length x chassis width approx. 2,200 mm x 2,850 mm Excavator bridge "BB-A": -Telescopic excavator bridge "BB-A" with drive-over bridge hooks at the front and with bolt-and-link coupling at the rear Ffsdpfx Aowcmhasa Rot -Length x base width approx. 6,650 mm x 2,850 mm -Beam height x beam width approx. 400 mm x 1,350 mm -Loading height 550 mm with ground clearance 150 mm 4-axle chassis at the rear: -Mechanical bolt-and-link coupling for attaching a low bed at the front, end cross member at the rear -Chassis length x Chassis width approx. 5,480 mm x 2,850 mm - Extensive lashing positions Pendulum axle and tires (front and rear chassis): - "Pendulum axle", all axles hydromechanically steered - Hose rupture valve on the axle compensation cylinder with automatic reset function - Hydraulic cylinder with shut-off valves and pins for securing in the raised position - Final axle paint finish with two coats of 2-component paint in MB 7350 Nova Gray - Technical axle load: 12,000 kg - Hydraulic axle compensation - Tires 285/70 R19.5 Steering: - Front and rear steering can be operated via cable remote control using push buttons, with axle alignment control - Power socket for operating the steering system on the chassis Gooseneck -Cable remote control with pushbuttons including axle alignment control Accessories included: -Yellow-red air couplings on the galvanized connection strip at the front -Steel bulkhead, approx. 400 mm high -4 wheel chocks -3.5" kingpins -One 7-pin socket on the left and right rear of the gooseneck for the warning sign -Gallows with winch for spare wheel on the front of the gooseneck -Truck hydraulic connection with flow regulator (40 l/min), including a boom for suspending the supply lines. The tractor unit's tank must hold at least 80 liters with couplings -Aluminum side walls and rear wall that can be attached to the gooseneck, approx. 400 mm high, anodized -Control lever on the gooseneck protected by a hinged cover -A separate air connection with air gun on the gooseneck -Bekamax central lubrication system, 1x on the Gooseneck, 1x on the 2-axle chassis and 1x on the 4-axle chassis - Variomax tool kit - Multi-coupling hydraulic connections on the gooseneck and in the area of the low-loader hook attachment - 2 spare wheels - One 7-pin socket on the left and right, front and rear of the rear chassis for the warning sign - Front chassis with a separate air connection for pneumatic screwdrivers - Foldable extensions with steel mattresses, adjustable in width from approx. 2,850 mm to approx. 3,250 mm - The steel mattresses can be inserted in two positions to create a lowered loading area - Steel mattresses with rubber flooring, approx. 12 mm thick - Screw-in option (⌀ 40 mm) every approx. 500 mm outside on the upper chord of the outer tube of the excavator bridge for screw rings - One locking point every approx. 500 mm on the extension with mechanical locking Locking mechanism -A socket on the rear chassis for the cable remote control of the self-steering system -Two reversing lights on the rear panel -Four warning signs, approximately 423 x 423 mm, extendable by approximately 2,000 mm, with a position light -One work light, left and right, on the rear panel of the gooseneck with separate on/off switches -Two stainless steel tool boxes, approxim

Condition: new, empty load weight: 10,300 kg, maximum load weight: 39,200 kg, overall weight: 49,500 kg, axle configuration: 3 axles, loading space length: 9,300 mm, loading space width: 2,540 mm, loading space height: 860 mm, suspension: air, tire size: 235/75 R 17.5, color: grey, Equipment: ABS, Gooseneck: -gooseneck with rear bevel of approx. 750 mm x 10° -3 pairs of lashing rings (LC 5,000 daN) -Hardwood decking 30 mm thick Loading area: -Loading surface can be raised and lowered hydraulically after the gooseneck Length approx. 2,800 mm, with rear slope of approx. 1,000 mm x 8° Cut-outs in the outer frame of the cargo bed for attaching tensioning straps (LC 2,000 daN) -Hardwood flooring approx. 48 mm thick, checker plate flooring over the axles Two-part steel ramps: -One pair of galvanized two-part steel ramps approx. 2,750 + 1,400 x 800 mm with approx. 48 mm thick hardwood decking -Ramp with hydraulically folding and unfolding ramp sections, hydraulic lifting gear and hydraulically movable -Maximum load per pair: 40,000 kg Axles, suspension and tires: -BPW axles and suspension, 2 axles rigid, 1 axle self-steering -Technical axle load: 12,000 kg Fsdju Hp Hropfx Aa Rjft -Electromagnetic reverse lock via reverse gear and can be activated manually -Air suspension with lifting and lowering valve -axle tool -235/75 R 17.5 3PMSF tires -TPMS tire pressure monitoring system in accordance with ECE R 141 Accessories included: -One spare wheel with holder in front of the bulkhead -2" kingpin -One galvanized steel bulkhead approx. 400 mm high -Yellow-red air couplings on the galvanized connection strip at the front -4 pieces of restraining shoes -Galvanized folding supports under the bevel of the cargo bed -A bracket for a rotating beacon at the rear of the trailer -Cover plates to bridge the space between the ramps and the cargo bed -White reflective tape in accordance with EU regulations on the side of the trailer and red at the rear -Electric hydraulic unit at the rear, under the cargo bed -One bracket for the warning signs on the gooseneck and on the ramps on the left and right, including socket -Control valves for the ramps fitted on the right-hand side of the trailer -European reflector signs (red/yellow) at the rear of the trailer -Manual and description on USB stick -ALU drop sides and rear wall can be plugged onto the gooseneck approx. 2,440 x 400 mm -The rear, galvanized stanchions are removable (length of the body approx. 2,560 mm) -An electric cable winch with radio remote control approx. 5,400 kg lifting force, including 9.5 mm thick wire rope 24 m long with rope guide roller -Screwed 5to ring for reeving the cable winch cable on the neck without deflection pulley -2 pairs of WADER container pockets in the loading area for a 20ft container -6 pairs of stanchion pockets for 100 x 50 mm stanchions in the outer frame of the cargo bed -Lift axle on the front axle with control by TEBS E depending on the current axle load and the current loading condition -7 pairs of recessed lashing rings along the central beam (LC 5,000 daN) -1 pair of recessed lashing rings along the central beam at the rear of the bevel (LC 10,000 daN) -A layer of sand painted onto the chequer plates on the gooseneck and on the cargo bed to prevent slipping -BEKAMAX (Pico) central lubrication system with NLGI-2 standard grease and removable protection around the pump -Four warning signs extendable by approx. 400 mm approx. 423 x 423 mm -Speed sticker 80 km/h at the rear and on both sides -Load manometer to determine the axle loads including load diagram -HRM metallization (High Resistance Metallization) of the outer frame -Complete steel construction shot-blasted, then the defined visible surfaces hot-finished in metallization with ZINACOR 850 (zinc 85% - aluminium 15%)

Condition: new, empty load weight: 34,500 kg, maximum load weight: 106,700 kg, overall weight: 141,200 kg, axle configuration: > 3 axles, loading space length: 7,150 mm, loading space width: 2,850 mm, loading space height: 580 mm, tire size: 285/70 R19.5, color: grey, operation weight: 34,500 kg, Equipment: ABS, Gooseneck: -Gooseneck hydraulically raises/lowers and can be removed -Length approx. 3,650 mm -Extensive lashing positions -For tractor units: 6 x 4 or 8 x 4 3-axle compact front chassis: -Hook attachments at the front and rear -Chassis length x chassis width approx. 3,560 mm x 2,850 mm -Extensive lashing positions Excavator bridge "BB-A": -Telescopic excavator bridge "BB-A" with drive-over bridge hooks at the front and with bolt-and-link coupling at the rear -Length x base width approx. 7,150 mm x 2,850 mm -Beam height x beam width approx. 430 mm x 1,350 mm -Loading height 580 mm with ground clearance 150 mm -5 pairs Hanging lashing rings (LC 10,600 daN) -4 pairs of M30 threaded blocks on the inner beam for mounting screwable rings 5-axle rear chassis: -Mechanical bolt-on coupling for attaching a drop-bed at the front, end cross member at the rear -Chassis length x chassis width approx. 6,840 mm x 2,850 mm -Extensive lashing positions Pendulum axle and tires (front and rear chassis): -"PENDULUM AXLE", all axles hydromechanically forced steered -Hose rupture valve on the axle compensation cylinder with automatic RESET function -Hydraulic cylinder with shut-off valves and cotter pins for securing in the raised position -Final painting of the axles with two coats of 2-component paint, painted in MB 7350 Nova Gray Ffjdpfowhywfsx Aa Ret -Technical axle load: 14,640 kg (62) km/h) -Hydraulic axle compensation -Axle tool -Tires 285/70 R19.5 Steering: -Steering can be operated from the front and rear using a cable remote control with push buttons, with axle alignment control -Socket for operating the steering on the gooseneck -Cable remote control with push buttons including axle alignment control Accessories included: -Yellow-red air couplings on the galvanized connection strip at the front -Steel bulkhead, approx. 400 mm high -4 wheel chocks with brackets -2 spare wheels 285/70 R19.5 -3.5" kingpin -Gallows with winch for spare wheel on the front of the gooseneck -Truck hydraulic connection with flow regulator (40 l/min), including a boom for suspending the supply lines. The tractor unit's tank must have a capacity of at least 80 liters. Couplings -White reflective tape in accordance with EU regulations on the sides and extension, red at the rear -Aluminum side walls and rear wall, approximately 400 mm high, anodized, attachable to the gooseneck -Operating lever on the gooseneck protected by a hinged cover -A separate air connection with an air gun on the gooseneck -Bekamax central lubrication system with NLGI-2 grease, 1x on the gooseneck, 1x on the 3-axle chassis, and 1x on the 5-axle chassis -Variomax tool kit -Multi-coupling hydraulic connections in the area of the low-bed hook receptacle -Front chassis with a separate air connection for pneumatic screwdrivers -Screw-in option (ø 40 mm) every approximately 500 mm on the outside of the upper chord of the outer tube of the excavator bridge for screw rings -Foldable extensions with steel mattresses, adjustable in width from approximately 2,850 mm to approx. 3,250 mm -Steel mattresses with rubber flooring, approx. 12 mm thick -Two stainless steel toolboxes (855 x 340 x 390 mm) -Radio remote control for the steering in addition to the cable remote control -Painted sand layer as anti-slip protection -1-cylinder Hatz diesel engine (Silent Pack) with electric starter and starter battery

Condition: used, empty load weight: 16,500 kg, maximum load weight: 63,500 kg, overall weight: 80,000 kg, axle configuration: > 3 axles, first registration: 02/2024, loading space length: 8,800 mm, loading space width: 2,540 mm, suspension: air, tire size: 235/75 R 17.5, color: grey, Year of construction: 2024, operation weight: 16,500 kg, Equipment: ABS, You will receive a current and complete inspection and functional report for every used trailer. Gooseneck: -Gooseneck in SNT design to optimize the loading area length, length approx. 3,700 mm, with a bevel at the rear of approx. 1,000 mm x 10° -Technical fifth wheel load: 30,000 kg -For tractor units: 4x2, 6x2 and 6x4 Loading area: -Loading area in double-extendable design, length approx. 8,800 mm with a bevel at the rear of approx. 500 mm x 10° -An approx. 300 mm wide support table with long holes at the front and rear for optional bridging elements that can be attached and moved is welded to the middle support -Pneumatic locking with conical locking bolt and reinforced locking positions, the supply lines are protected in the extendable supports and automatically adjust to the respective loading area length Axles and tires: -BPW axles and Suspension, 1st axle with leading steering, all other axles with hydro-mechanical forced steering -1. Axle with electro-magnetic reversing lock, can be activated via reverse gear and manually -Technical axle load: 12,000 kg air suspension with lifting and lowering valve -235/75 R 17.5 3PMSF twin tires -Load index 143/141J Accessories: -Steel bulkhead, pluggable, approx. 400 mm high -Connection strip for supply lines to the tractor unit, installed at the height of the outer frame profile -Spiral cable to supply the electro-hydraulic unit and/or the electric cable winch (35 mm2, 3.5 m long) between the trailer and tractor unit with plug -3 kW electro-hydraulic unit to control the hydraulic processes, with the exception of hydraulic cable winches -Parking position on the gooseneck for the warning signs when not in use -1 spare wheel -1 pair of pluggable aluminum side walls on the gooseneck side, approx. 400 mm high, anodized -On the gooseneck a plug-in aluminum rear wall, approx. 400 mm high, anodized -Hardwood covering on the slope of the loading area -3.5" kingpin (optional 2") -Guide plate from the gooseneck for the fifth wheel plate, approx. 500 mm wide -2 brake shoes with bracket -Mechanical saddle supports with 2-speed gearbox and crank Fodpfx Ajv Aun Aoa Rjft -JOST module B - static test load = 50,000 kg -On the loading area, continuous hardwood covering, approx. 50 mm thick, interrupted between the axles -Locking of the loading area with conical welded locking profiles, on the first 3,000 mm extension of the extension tube with a large cross-section, a locking point every 500 mm -Elongated holes for hanging and movable bridging elements: on the loading area front -Extensions (galvanized) extendable by approx. 230 mm per side -1 pair of mechanical rear supports -Central lubrication system with 1 pump -One single-piece INOX storage box, approx. 2,480 x 340 x 390 mm -Radio remote control for operating the steering, in addition to the cable remote control, with 2 indicator lights on the receiver as a lane control -2 axle load gauges mounted on the left side including axle load diagram -1st axle with automatic lifting axle function -4 warning signs, approx. 423 x 423 mm, extendable -Complete HRM metallization (High Resistance Metallization) -Complete steel construction shot blasted, then hot-finished with ZINACOR 850 (zinc 85% - aluminum 15%)

Condition: new, empty load weight: 15,450 kg, maximum load weight: 65,550 kg, overall weight: 80,000 kg, axle configuration: > 3 axles, loading space length: 21,900 mm, loading space width: 2,540 mm, loading space height: 925 mm, suspension: air, tire size: 235/75 R 17.5, color: grey, Equipment: ABS, Gooseneck: Gooseneck in SNT design to optimize the loading area length, length approx. 3,700 mm, rear with bevel approx. 1,000 mm x 10° Technical fifth wheel load: 30,000 kg. For tractor units: 4x2, 6x2 and 6x4 Loading area: Loading area in double-extendable design, length approx. 8,800 mm with bevel at the rear approx. 500 mm x 10°. A support table approx. 300 mm wide with long holes at the front and rear for optional bridging elements that can be hung and moved is welded to the middle support. Pneumatic locking with conical locking bolt and reinforced locking positions, the supply lines are protected in the extendable supports and automatically adjust to the respective loading area length. Axles and tires: BPW axles and suspension, 1st axle with pre-steering, all other axles with hydro-mechanical forced steering. 1st axle with electro-magnetic reversing lock that can be activated via reverse gear and manually. Technical axle load: 12,000 kg Air suspension with lifting and lowering valve Manufacture of our choice Sockets and lighting: 24-volt lighting system Design in accordance with EU regulations ASPÖCK-UNIBOX on the front connection strip with 24N, 24S & 15-pin sockets Complete HRM metallization Complete steel construction shot blasted, then hot-finished with ZINACOR 850 Paint: 6-K final treatment: Complete steel construction shot blasted after welding 1 layer of zinc-based base paint, 1 layer of adhesion primer. Final painting with 2 layers of 2-K paint in one color in DB 7350 Nova gray, then sealing of the cavities with special wax Accessories: Bulkhead made of steel, pluggable, approx. 400 mm high Connection strip for supply lines to the tractor unit, attached at the height of the outer frame profile ASPÖCK-UNIBOX on the front connection strip with sockets 24N, 24S & 15-pin. If your pin assignment differs from the ISO connection standard, please let us know 3 kW electro-hydraulic unit for controlling the hydraulic processes, with the exception of hydraulic cable winches On the gooseneck 1 pair of plug-in aluminum side walls, approx. 400 mm high, in anodized design. 3.5" kingpin. Gooseneck guide plate for the fifth wheel plate, approx. 500 mm wide 2 brake shoes with bracket in front of the bulkhead. Mechanical seat supports with 2-speed gearbox and crank. Control valves for the hydraulic ramps on the right of the vehicle 1 pair of mechanical rear supports. Central lubrication system with 1 pump, brand BEKAMAX, with normal grease according to NLGI-2 Removable protection around the central lubrication pump(s) Steering from the front and rear can be operated using a cable remote control via push buttons, with alignment control of the axles, without installation in the tractor unit Fedpferigw Rjx Aa Reft Under the gooseneck, as well as on the end cross member, left and right, one 7-pin socket with bracket for the warning signs A 7-pin socket on the end cross member Manual and description One INOX storage box, one-piece, approx. 2,480 x 340 x 390 mm in a straight design Please note that Special equipment and accessories generally increase the dead weight and reduce the payload accordingly Warning package: 4 warning signs, approx. 423 x 423 mm, extendable by approx. 1,000 mm, including 2 LED position lights and brackets for rotating beacon.

Condition: new, maximum load weight: 38,100 kg, overall weight: 50,000 kg, axle configuration: > 3 axles, loading space length: 13,100 mm, loading space width: 2,480 mm, loading space height: 760 mm, suspension: air, tire size: 205/65 R17.5 3PMSF, color: grey, Equipment: ABS, Gooseneck: Gooseneck with rear bevel of approx. 750 mm x 10° 3 pairs of lashing rings Hardwood decking 30 mm thick Loading area: 5 pairs of lashing rings can be folded outwards 3 pairs of lashing rings can be folded outwards 1 pair of lashing rings lying in the front of the cargo bed Cut-outs in the outer frame of the cargo bed for attaching lashing straps Hardwood flooring approx. 48 mm thick, checker plate flooring over the axles Seat posts: JOST seat posts with 2-speed gearbox for 24 t lifting capacity Axles and tires: BPW axles, two axles rigid two axles self-steering, air-sprung, with drum brake, with raise/lower function The self-steering axles with electromagnetic reverse lock can be activated via reverse gear or manually Axle tool Tires 205/65 R17.5 3PMSF Brake system: WABCO brake system in accordance with EU regulations with EBS-E Steel construction: Steel construction made from high-strength fine-grained steels Steel grades: S355J2+N/S355MC S690QL/S700MC Electrical equipment: Electrical system in accordance with EU regulations, 24 volt lighting ASPÖCK-NORDIK ASPÖCK-UNIBOX on the front connection strip with 24N, 24S & 15-pin sockets Connection according to ISO Paintwork: First-class and durable corrosion protection of the standard shot-peened welded frame guaranteed by a 2-component zinc dust primer A high-quality 2-component Top coat single color in MB 7350 nova grey No metallic paint finish possible Rear section metallized and painted in RAL 9010 Accessories included: 1 spare wheel 205/65 R 17.5 TPMS tire pressure monitoring system in accordance with ECE R 141 Yellow-red air couplings on the galvanized connection strip at the front 4 brake shoes with holder on the bulkhead Mounting in the rear area of the gooseneck for ALU docking lights Galvanized folding supports under the bevel of the cargo bed A holder for a rotating beacon at the rear of the trailer Height-adjustable tarpaulin body Galvanized bulkhead with a tensioning mechanism for the sliding curtains Height-adjustable by approx. 400 mm "EDSCHA" brand roof can be moved forwards on ALU roof rail profiles bolted to the front and rear wall 3 pairs of sliding stanchions in the loading area The body can be hydraulically widened at the rear to the left and right by approx. 750 mm Sliding roof with pivoting portal support Sliding tarpaulin with 700 mm reserve in length, with tension belts at approx. 600 mm intervals Height top edge of body approx. 3,960 mm Driving with the sliding tarpaulin open is not permitted and will damage the tarpaulin Suspension strip for ALU docking lights at the rear of the vehicle A holder for the warning signs including socket on the gooseneck and on the rear panel on the left and right respectively A mud flap at the rear of the trailer European reflector plates at the rear of the trailer 7 pairs of stanchion pockets for 100 x 50 mm stanchions in the outer frame of the cargo bed Lift axle on the front axle with control by TEBS E depending on the current axle load and the current load condition Rear body closed with ALU hinged doors Fsdpfxstphtmj Aa Reft A layer of sand painted onto the chequer plates on the gooseneck and on the cargo bed to prevent slipping BEKAMAX central lubrication system with NLGI-2 standard grease and removable protection around the pump Speed sticker 80 km/h at the rear and on both sides Load manometer to determine the axle loads including load diagram

Condition: new, empty load weight: 9,300 kg, maximum load weight: 38,700 kg, overall weight: 48,000 kg, axle configuration: 3 axles, loading space length: 13,600 mm, loading space width: 2,540 mm, loading space height: 1,200 mm, suspension: air, tire size: 385/65 R 22,5, color: grey-black, Equipment: ABS, Cargo bed: - Load surface in extendable design with pneumatically operated locking mechanism - Loading area with approx. 30 mm thick wooden floor - 7 pairs of lashing rings can be folded outwards (LC 5,000 daN) - 3 pairs of lashing rings can be folded outwards (LC 10,000 daN) - Cut-outs in the outer frame of the cargo bed for attaching lashing straps. (LC 2,000 daN) Axles and tires: - BPW axles and suspension, all axles with hydro-mechanical forced steering - With disk brakes - Technical axle load: 10,000 kg - Air suspension with lifting and lowering valve - Axle tool - Tires: 385/65 R 22.5 - TPMS tire pressure monitoring system in accordance with ECE R 141 Brake system: - WABCO braking system in accordance with EU regulations with EBS-E (2S2M) Electrical system: - Electrical system in accordance with EU regulations, 24 volt ASPÖCK-NORDIK lighting (ASS3) - ASPÖCK-UNIBOX on the front connection strip with 24N, 24S & 15-pin sockets - Connection according to ISO - 24N ISO-1185 - 24S ISO-3731 - 15-pin ISO-12098 Accessories included: - Re-steering can be operated from the front and rear by cable remote control via pushbuttons, with toe-in control of the axles - 4 wheel chocks with holder on the front wall - 2" kingpin - One galvanized steel bulkhead approx. 1,600 mm high - Yellow-red air couplings on the galvanized connection strip at the front - White reflector tape in accordance with EU regulations on the side, on the extension and at the rear of the trailer in red - European reflector plates (red/yellow) at the rear of the trailer Ffsdpfxsiu Etrs Aa Ret - A mud flap at the rear of the trailer - Manual and description - A bracket for a rotating beacon at the rear of the trailer - Loading area with approx. 30 mm thick wooden floor edged in omega profiles - 10 pairs of stanchion pockets for 100 x 50 mm stanchions in the outer frame of the cargo bed - 1 spare wheel holder under the cargo bed on the right in the direction of travel - Electro-hydraulic unit - On the gooseneck and on the rear panel on the left and right, one holder each for the warning signs including socket - A layer of sand painted onto the central beam to prevent slipping - 6 pairs of WADER container pockets in the loading area, for 1x20ft, 2x 20ft or 1x 40ft container, an additional locking point is provided in the pull-out for a 45ft container - 4 pairs of stanchion pocket rails, mounted transversely in the cargo bed, for 100 x 50 mm stanchions - Access ladder mounted on the right in the direction of travel - One HDPE tool box approx. 1,200 x 500 x 480 mm at the front under the cargo bed on the left in the direction of travel - Central lubrication system BEKAMAX (Pico) with removable protection around the pump - Lift axle on the front axle with control by TEBS E depending on the current axle load and the current load status - Radio remote control for steering in addition to the cable remote control, with indicator lights on the receiver for tracking control - Four warning signs extendable by approx. 400 mm approx. 423 x 423 mm with a position light - A holder for rotating beacon on the warning signs - Speed sticker 80 km/h at the rear and on both sides - Load manometer to determine the axle loads including load diagram - HRM metallization (High Resistance Metallization) of the outer frame - Complete steel construction shot-blasted, then the defined visible surfaces hot-finished in metallization with ZINACOR 850 (zinc 85% - aluminium 15%)

Condition: used, empty load weight: 17,450 kg, maximum load weight: 68,650 kg, overall weight: 85,000 kg, axle configuration: > 3 axles, first registration: 03/2024, loading space length: 9,400 mm, loading space width: 2,740 mm, loading space height: 850 mm, tire size: 245/70 R 17.5, color: grey, Year of construction: 2024, Equipment: ABS, Gooseneck: -Gooseneck in SNT design to optimize the loading area length, length approx. 3,700 mm, rear with bevel approx. 1,000 mm x 10° Cargo bed: -Loading area in extendable design with Super-Grip rubber coating over the axles, length approx. 9,400 mm with bevel at the rear approx. 500 mm x 10° -One recess in the loading area and protruding into the chamfer to accommodate the excavator dipper stick approx. 3950 x 780 x 370/450 mm -Pneumatic locking with conical locking pin and reinforced locking positions Axles and tires: Semi-axles type TWINAXLE II, independent wheel suspension, 1st axle self-steering, all other axles hydro-mechanically forced steered -1st axle with electro-magnetic reverse lock via reverse gear and manual activation -Technical axle load: 12,000 kg Fjdot Dpiyopfx Aa Roft -Hydraulic axle compensation -Hydraulic cylinder with shut-off valves -Tires: 245/70 R 17.5 3PMSF dual tires Two-piece steel ramps: -A pair of two-piece steel ramps with a length of approx. 4,650 mm and a width of approx. 900 mm -With Super-Grip rubber coating -Hydr. folding ramp tips -Ramps can be moved individually hydraulically by approx. 235 mm outwards and approx. 215 mm inwards Fully metallized: -Complete HRM metallization (High Resistance Metallization) -Complete steel construction shot-blasted, then hot-finished with ZINACOR 850 (zinc 85% - aluminum 15%) Accessories: -steel front panel, pluggable, approx. 400 mm high -1 INOX tool box, one-piece, approx. 2,480 x 340 x 390 mm -Round NATO socket on the front connection strip (Maeler & Kaege VG 96 917) -3 kW electro-hydraulic unit for controlling the hydraulic processes, with the exception of hydraulic cable winches -1 Spare wheel -On the gooseneck 1 pair of plug-in ALU side panels, approx. 400 mm high, anodized -One plug-in ALU rear panel on the gooseneck, approx. 400 mm high, anodized -Approx. 40 mm thick hardwood covering over the gooseneck, checker plate covering over the kingpin -Guide plate from the gooseneck for the saddle plate, approx. 500 mm wide -4 brake shoes -Mechanical seat posts with 2-speed gearbox and crank -JOST module B - static test load = 50,000 kg -Approx. 50 mm thick hardwood flooring on the loading area, checker plate flooring over the axles -Locking of the cargo bed with conically welded locking profiles every 250 mm, including pretensioning plate -1 Sliding intermediate table, approx. 300 mm wide -Widenings extendable by approx. 230 mm per side -1 Pair of hydraulic rear supports -Central lubrication system -Cable remote control operated via pushbuttons, with track-in control of the axles -Radio remote control Rubber floor "Super Grip" 25 mm and sheet metal floor Square climbing rails 20 x 30 mm WABCO Smart Board System Square climbing rails 20 x 30 mm, approx. every 200 mm on the outer frame of the ramp 4 warning signs, approx. 423 x 423 mm, extendable by approx. 1,000 mm, incl. 2 position lights and brackets for rotating beacon

Condition: new, empty load weight: 12,800 kg, maximum load weight: 36,200 kg, overall weight: 49,000 kg, axle configuration: 2 axles, loading space length: 6,850 mm, loading space width: 2,550 mm, loading space height: 375 mm, tire size: 245/70 R 17.5, color: grey, operation weight: 12,800 kg, Equipment: ABS, Gooseneck: - Gooseneck in SNT design to optimize the loading area length, length approx. 3,750 mm - Gooseneck hydraulically raised/lowered and removable - Technical fifth wheel load: 25,000 kg - For tractor units: 4 x 2, 6 x 2, and 6 x 4 Loading area: - Low bed with external supports, designed as a telescopic tank bridge in a low construction with a front extension - Length 6,850 mm x Width 2,540 mm - One locking point approximately every 1,000 mm on the extension Rear chassis: - Rear chassis with closed outer frame with checker plate cover and continuous prism excavator trough approx. 1,250/700 x 505 mm, open at the rear Axles, suspension, and tires: - "PENDEL-AXLE", all Hydro-mechanically forced-steered axles - Hose rupture valve on the axle balancing cylinder with automatic reset function - Hydraulic cylinder with shut-off valves and pins for securing in the raised position - Final axle painting with two coats of 2-component acrylic paint in a single color "FAY-Gray-34-0260" - Technical axle load: 12,000 kg - Hydraulic axle balancing - Tires: 245/70 R 17.5 - TPMS tire pressure monitoring system in accordance with ECE R 14 - TPMS tire pressure monitoring sensors installed in all wheels, including spare tires Accessories included: - Steel bulkhead, plug-in, approx. 400 mm high - 3 kW electro-hydraulic unit for controlling the hydraulic processes, with the exception of hydraulic cable winches - One spare tire with mounting adapter - Gooseneck outer support with mounting holes for screwable lashing rings -Slidable aluminum side walls on the gooseneck, approx. 400 mm high, anodized -Slidable aluminum rear wall on the gooseneck, approx. 400 mm high, anodized -Checker plate covering above the gooseneck -Gooseneck guide plate for the fifth wheel plate, approx. 500 mm wide -Illuminated control panel on the gooseneck with on/off switch -Hydraulic crossbar for supporting the gooseneck on the tractor unit or a dolly -2" kingpin -Anti-slip sticker on the left slope of the gooseneck -Gooseneck closed at the rear upper area with a removable cover -4 chocks with brackets -Hydraulic connections from the gooseneck to the drop bed with multi-coupling instead of screw couplings -1 pair of steel ramps with climbing rails and fastening bolts for bridging the drop bed's hooks -The Ramps can be installed over or between the hooks. -Attachment option for the steel loading ramps at the rear between the outer supports of the gooseneck. -Prepared for screw-on container holders for 1x20f on the outer support. -Mechanical bolt-and-lug coupling from the low bed to the chassis, for replacing the loading area or installing extension supports. -With electro-pneumatic-hydraulic couplings. Ffjdpfovy Edcsx Aa Ret -The outer supports of the low bed are provided with a painted layer of sand as a slip protection. -Removable loading floor (galvanized) in 3 elements, insertable between the outer supports with hardwood flooring. -Foldable extensions, by approximately 230 mm per side. -Hanging rail at the front of the rear chassis to the low bed for loose loading ramps. -2 pairs of stake pockets recessed into the outer frame of the chassis, for plug-in stakes approx. 100 x 50 mm. -Hanging rail for loose Aluminum docking ramps on the vehicle's end crossbar -Central lubrication system with 2 pumps -Wireless and cable remote control -4 warning signs, approximately 423 mm x 423 mm extendable -Extensive lashing positions

Condition: new, empty load weight: 10,600 kg, maximum load weight: 39,400 kg, overall weight: 50,960 kg, axle configuration: > 3 axles, loading space length: 9,300 mm, loading space width: 2,540 mm, loading space height: 760 mm, suspension: air, tire size: 205/65 R17.5, color: grey, operation weight: 10,600 kg, Equipment: ABS, Gooseneck: -Gooseneck with hardwood covering, 30 mm thick -Gooseneck at the rear, straight design -3 pairs of lashing rings (LC 5,000 daN) Loading area in extendable design: -Loading area in extendable design -5 pairs of lashing rings that can be folded outwards -3 pairs of lashing rings that can be folded outwards -1 pair of lashing rings lying in the front of the loading area -Cutouts in the outer frame of the loading area for hanging tensioning straps -Hardwood covering, approx. 48 mm thick, checkered sheet covering over the axles Seatposts: -JOST seatposts (mechanical) with 2-speed gearbox for 24t lifting load (50t test load) Axles and tires: -BPW axles, two axles rigid, two axles with self-steering -Air suspension, with drum brake, with lifting/lowering- Function -The self-steering axles with electro-magnetic reversing lock can be activated via reverse gear or manually -Axle tool -Tires 205/65 R17.5 Braking system: -Braking system in accordance with EU regulations with EBS-E (4S3M) Steel construction: -Steel construction made of high-strength fine-grain steels -Steel qualities: -S355J2+N/S355MC (yield strength 355MPa) -S690QL/S700MC (yield strength 690MPa) Electrical system: -Electrical system in accordance with EU regulations, lighting 24 volts, ASPÖCK-NORDIK (ASS3) -ASPÖCK-UNIBOX on the front connection strip with 24N, 24S & 15-pin sockets -Connection in accordance with ISO: -24N ISO-1185 -24S ISO-3731 -15-pin ISO-12098 Painting: -First-class and long-lasting corrosion protection of the standard shot-blasted welded frame guaranteed by a 2-component (2K) zinc dust primer -A high-quality 2-component (2K) top coat in a single color in Nova gray -Rear section metallized and painted in RAL 9010 (pure white) Accessories included: -A spare wheel with holder in front of the bulkhead -2" kingpins -A galvanized steel bulkhead approx. 400 mm high -Yellow-red air couplings on the galvanized connection strip at the front -4 brake shoes with holder on the bulkhead -Galvanized folding supports under the bevel of the loading area -A bracket for a rotating beacon at the rear of the trailer -Galvanized extensions, extendable by approx. 230 mm on each side -White Reflective tape in accordance with EU regulations on the side, on the extension and at the rear, red -On the gooseneck and on the rear panel on the left and right, a holder for the warning signs including a socket -European reflector signs (red-yellow) on the rear of the trailer -TPMS tire pressure monitoring system in accordance with ECE R 141 -ALU side walls and rear wall can be plugged into the gooseneck, approx. 2,440 x 400 mm -The rear, galvanized plug-in stanchions are removable, length of the structure approx. 2,560 mm -7 pairs of WADER container bags -1x 20ft container in the loading area; 1x 40ft container in the loading area; 1x 40ft container above the gooseneck; 2x 20ft containers -7 pairs of stake pockets for 100 x 50 mm stakes in the outer frame of the loading area -Lift axle on the front axle with control by TEBS E depending on the current axle load and the current loading status -Movable mounting rail for aluminum loading ramps at the rear of the vehicle -A painted layer of sand on the checker plates on the gooseneck and on the loading area to prevent slipping -Four warning signs, approx. 423 x 423 mm, extendable by approx. 400 mm, with a position light -A holder for a rotating beacon on the warning signs -Speed sticker 80 km/h at the rear and on both sides Ffjdot Ag Uwepfx Aa Ret -L

Condition: new, maximum load weight: 38,800 kg, overall weight: 49,500 kg, axle configuration: 3 axles, loading space length: 9,300 mm, loading space width: 2,540 mm, loading space height: 860 mm, suspension: air, tire size: 235/75 R 17,5 3PMSF, color: grey, Equipment: ABS, Gooseneck: Ffjdpfx Aaeuqlmnj Rjt -Gooseneck with beveled corners at the front 45° and with rear bevel of approx. 750 mm x 10° -3 pairs of lashing rings (LC 5,000 daN) -Hardwood decking 30 mm thick Loading area in extendable version: -Loading surface in extendable version with rear slope of approx. 1,000 mm x 8° -6 pairs of lashing rings can be folded outwards (LC 5,000 daN) -3 pairs of lashing rings can be folded outwards (LC 10,000 daN) -1 pair of lashing rings lying in the front of the cargo bed (LC 10,000 daN) Cut-outs in the outer frame of the cargo bed for attaching lashing straps (LC 2,000 daN) -Hardwood flooring approx. 48 mm thick, checker plate flooring over the axles Axles and tires: -PW axles and suspension, 2 axles rigid, 1 axle self-steering -Technical axle load: 12,000 kg -Electro-magnetic reverse lock via reverse gear and can be activated manually -Air suspension with lifting and lowering valve -axle tool -235/75 R 17.5 3PMSF Brake system: -WABCO brake system in accordance with EU regulations with EBS-E (2S2M) Seat posts: -JOST seat posts (mechanical) with 2-speed gearbox for 24t lifting load (50t test load) Accessories included: -One spare wheel with holder in front of the bulkhead -2" kingpin -One galvanized steel bulkhead approx. 400 mm high -Yellow-red air couplings on the galvanized connection strip at the front -4 wheel chocks with holder on the bulkhead -One bracket for rotating beacon at the rear of the trailer -Mounting in the rear area of the gooseneck for ALU trailer lights -Galvanized folding supports under the bevel of the cargo bed -Cover plates to bridge the space between the ramps and the cargo bed -White reflective tape in accordance with EU regulations on the sides, on the extension and red at the rear -Electric hydraulic unit at the rear, under the cargo bed -On the gooseneck and on the ramps on the left and right a holder for the warning signs including socket -Control valves for the ramps mounted on the right-hand side of the trailer -One mud flap at the rear of the trailer -Manual and description on USB stick -ALU drop sides and rear wall approx. 2,440 x 400 mm on the gooseneck -The rear, galvanized stanchions are removable (length of the body approx. 2,560 mm) -Four warning signs approx. 423 x 423 mm with one position light, extendable by approx. 400 mm -3 pairs of WADER container pockets in the loading area for a 20ft, 30ft or 40ft container -6 pairs of stanchion pockets 100x50 mm in the outer frame of the cargo bed -Galvanized extensions, extendable by approx. 230 mm per side -Square climbing rails 20 x 20 mm every 200 mm on the outer frame of the loading area slope -A layer of sand painted onto the chequer plates, above the kingpin and the cargo bed to prevent slipping -On the warning plates a holder for rotating beacon -European reflector plates (red/yellow) at the rear of the trailer -Speed stickers 80 km/h at the rear and on both sides -Load manometer to determine the axle loads including load diagram -HRM metallization (High Resistance Metallization) of the outer frame -Complete steel construction shot-blasted, then the defined visible surfaces hot-finished in metallization with ZINACOR 850 (zinc 85% - aluminium 15%)

Condition: new, empty load weight: 7,900 kg, maximum load weight: 41,600 kg, overall weight: 49,500 kg, axle configuration: 3 axles, loading space length: 8,600 mm, loading space width: 2,540 mm, loading space height: 860 mm, suspension: air, tire size: 235/75 R 17,5, color: grey, operation weight: 7,900 kg, Equipment: ABS, Gooseneck: -Gooseneck with rear bevel of approx. 750 mm x 10° -3 pairs of lashing rings (LC 5,000 daN) -Hardwood decking 30 mm thick Loading area: Ffedpfounrapjx Aa Ret -Loading surface with rear slope of approx. 1,000 mm x 8° -Recess in the chamfer and protruding into the loading surface to accommodate the excavator dipper stick approx. 2,900 x 750 x 210/290 mm Cut-outs in the outer frame of the cargo bed for attaching tensioning straps -Hardwood flooring approx. 48 mm thick, checker plate flooring over the axles Seat posts: -JOST fifth-wheel supports (mechanical) with 2-speed gearbox for 24 t lifting load (50 t test load) Axles and tires: -BPW axles and suspension, 2 axles rigid, 1 axle self-steering -Technical axle load: 12,000 kg -Electromagnetic reverse lock via reverse gear and can be activated manually -Air suspension with lifting and lowering valve -TPMS tire pressure monitoring system in accordance with ECE R 141 -235/75 R 17.5 tires Paint finish: -Complete steel construction automatically blasted after welding with blast wheel system -second blasting with corundum for optimum adhesion of the coating system -Finishing coat with 2 layers of 2K top coat, single color in RAL MB 7350 nova grey -Rims painted in silver -Rear section metallized and painted in RAL 9010 (pure white) -Sealing of cavities with special wax Electrical system: -Electrical system in accordance with EU regulations, lighting 24 volt ASPÖCK-NORDIK (ASS3) ASPÖCK-UNIBOX at the front connection strip with sockets 2x 7-pin & 1x15-pin Accessories included: -Extensive lashing positions -2" kingpin -One galvanized steel end wall approx. 400 mm high -Yellow-red air couplings on the galvanized connection strip at the front -4 restraining shoes with holder on the bulkhead -Mounting in the rear area of the gooseneck for ALU docking ramps -Galvanized folding supports under the bevel of the cargo bed -One bracket for a rotating beacon at the rear of the trailer -Galvanized extensions, extendable by approx. 230 mm per side -White reflector tape in accordance with EU regulations on the sides and red at the rear -On the gooseneck and on the rear plate on the left and right, one bracket each for the warning signs including socket -ALU drop sides and rear panel can be plugged onto the gooseneck approx. 2,440 x 400 mm -The rear, galvanized stanchions are removable -2 pairs of WADER container pockets in the loading area for a 20ft container -6 pairs of stanchion pockets for 100 x 50 mm stanchions in the outer frame of the cargo bed -Sliding attachment strip for ALU docking ramps at the rear of the vehicle -Square climbing rails 20 x 20 mm every 200 mm on the outer frame of the loading area slope -a layer of sand painted onto the chequer plates on the gooseneck and on the cargo bed to prevent slipping -Four warning signs that can be extended by approx. 400 mm, approx. 423 x 423 mm with a position light -One bracket for rotating beacon on the warning signs -Speed sticker 80 km/h at the rear and on both sides -European reflector plates (red/yellow) at the rear of the trailer -Manual and description on USB stick -HRM metallization (High Resistance Metallization) of the outer frame -Complete steel construction shot-blasted, then the defined visible surfaces hot-finished in metallization with ZINACOR 850 (zinc 85% - aluminium 15%)

Condition: used, maximum load weight: 34,100 kg, overall weight: 47,000 kg, axle configuration: 2 axles, first registration: 05/2021, loading space length: 6,850 mm, loading space width: 25,400 mm, loading space height: 350 mm, tire size: 245/70 R 17.5, color: grey, Year of construction: 2021, Equipment: ABS, Gooseneck: - Gooseneck in SNT design for optimized loading area length, approx. 3,785 mm long - Gooseneck hydraulically liftable/lowerable as well as detachable - Technical kingpin load: 23,000 kg - For tractor units: 4x2, 6x2, and 6x4 Loading Area: - Low-bed with external beams in extendable “SUPER LOW” design, approx. 6,850 mm in length - Low-bed section with fixed hardwood floor, approx. 40 mm thick, and pneumatically actuated locking mechanism - Supply lines are protected inside the extendable beams and automatically adapt to the respective length of the low-bed - 6 pairs of threaded blocks on the inner beam for mounting bolted RUD lashing rings Rear Chassis: - Rear chassis with closed outer frame, checker plate covering, and continuous prism-shaped excavator trough approx. 1,250/700 x 505 mm, open at the rear Axles and Tyres: - Pendulum axles, all axles hydro-mechanically forcibly steered - Hose rupture valve on the axle compensation cylinder with automatic RESET function - Hydraulic cylinders with shut-off valves and positioning pins for securing in raised position - Technical axle load: 12,000 kg - Hydraulic axle compensation - Axle tool kit - Tyres: 245/70 R 17.5 Braking System: - Braking system compliant with EU regulations with EBS-E, without connection lines to the tractor unit Paintwork: - First-class and durable corrosion protection of the standard shot-blasted welded frame, ensured by a 2-component zinc dust primer - Rear section metallized and painted in RAL 9010 Included Accessories: - Prepared for bolted container locks for 1x 20' or 1x 40' containers on the external beams - One galvanized steel front wall approx. 400 mm high - At the galvanized front connection bar, yellow and red air couplings - 2 wheel chocks with holder on the front wall - Rear steering from front and rear via cable remote control with push buttons, including single-track control of the axles Fsdpsrtqylefx Aa Rjft - Hydraulic connections from gooseneck to low-bed with multi-coupling instead of threaded couplings - Electro-hydraulic unit - On the gooseneck and on the rear plate, left and right, a holder for warning panels incl. socket - On the gooseneck, plug-in ALU side walls and rear wall, approx. 2,440 x 400 mm - The rear galvanized stakes are removable - 5 pairs of stake pockets for 100 x 50 mm stakes in the outer frame of the loading area, 2 pairs in the outer frame of the chassis - Folding extensions, approx. 230 mm per side - 1 pair of steel ramps for bridging the low-bed mounting hooks - 80 km/h speed stickers at the rear and on both sides - On the warning boards, a mount for a revolving beacon - Radio remote control for rear steering in addition to the cable remote, with LED indicators on the receiver as single-track control - Central lubrication system with 2 BEKAMAX (Pico) pumps with standard grease NLGI-2 and removable protection around the pump - Excavator dipper trough at the rear chassis closed at the rear with a plug-in plate

Condition: used, empty load weight: 13,600 kg, maximum load weight: 56,200 kg, overall weight: 69,800 kg, axle configuration: > 3 axles, first registration: 11/2024, loading space length: 8,800 mm, loading space width: 2,540 mm, loading space height: 860 mm, suspension: air, tire size: 235/75 R17.5, color: grey, Equipment: ABS, Gooseneck: -Gooseneck in SNT design to optimize the loading area length, length approx. 3,700 mm -Rear gooseneck with bevel approx. 1,000 mm x 10° Cargo bed: -Telescopic loading area, length approx. 8,800 mm, with rear chamfer approx. 500 mm x 10° -Depression in the chamfer and protruding into the loading area to accommodate the excavator dipper arm -Pneumatic locking with conical pin and reinforced locking positions Ramps: -1 Pair of two-part steel ramps, approx. 4,350 mm x 900 mm Ffedpfx Aovitawea Rjt -Hydraulic folding ramp tips -Individual hydraulic ramps can be moved outwards by approx. 235 mm and inwards by approx. 215 mm Axles and suspension: -PW axles and suspension, two axles rigid, two axles self-steering -Electromagnetic reverse lock via reverse gear and can be activated manually -Air suspension with lifting and lowering valve -axle tool -Tires: 235/75 R17.5 3PMSF dual tires Accessories included: -steel front wall, plug-in, height approx. 400 mm -3 kW electro-hydraulic unit for controlling the hydraulic processes, with the exception of hydraulic cable winches -1 Spare wheel with mounting adapter -Outer support of the gooseneck with fastening holes for screwable lashing rings -The first hole approx. 200 mm from the front, then approx. every 400 mm -One fastening hole in the rear upper area of the gooseneck outer support for a screwable lashing ring -above the gooseneck approx. 40 mm thick hardwood covering -1 pair of plug-in aluminum side panels on the side of the gooseneck and a plug-in aluminum rear panel -2" kingpin -Guide plate of the gooseneck for the saddle plate approx. 500 mm wide -Mounting for ALU docking lights -Mech. Saddle supports with 2-speed gearbox and crank -Continuous hardwood flooring on the cargo bed, interrupted between the axles, approx. 50 mm thick -Locking of the cargo bed with conically welded locking profiles every 250 mm incl. pretensioning plate -elongated holes for hook-in and movable bridging elements on the front of the cargo bed -1 Intermediate table with stepped loading surface, approx. 300 mm wide for the pull-out tube with large cross-section with sheet metal covering -Front and rear with slotted holes for hook-in and movable bridging elements: -Removable cover at the same height as the loading area -Widenings extendable by approx. 230 mm per side -1 pair of fixed wheel recesses open up to the pull-out, approx. 700 x 410 mm, in the cargo bed in front of the 1st axle -Wheel recesses with sheet metal covering and square climbing ledges 15 x 15 mm each approx. 200 mm -A pair of fixed wheel recesses between the 2nd and 3rd axles in the loading area -Hardwood covering on the bevel of the cargo bed -Control valves for the hydraulic ramps on the right-hand side of the vehicle -1 pair of mechanical rear supports -Central lubrication system -Galvanized stands for the extendable extensions in the wheel recesses, for widening the wheel recess covers -Square climbing rails 20 x 30 mm, approx. every 200 mm -WABCO Smartboard System -1st axle with automatic lift axle function and collision aid -Square climbing ledges 20 x 30 mm -4 warning boards approx. 423 x 423 mm extendable by approx. 1,000 mm -1 Intermediate table with offset loading surface, approx. 300 mm wide for the pull-out tube with large cross-section with sheet metal covering -With slotted holes at the front and rear for attachable and movable bridging elements -Removable cover at the same height as the loading surface