Used Faymonville Trailers for sale (146)

Condition: new, maximum load weight: 36,020 kg, overall weight: 48,000 kg, axle configuration: 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our full vehicle inventory, including immediately and short-term available vehicles, on our website. Excerpts from the equipment. Complete equipment details available on request. Gooseneck: * Gooseneck with rear bevel approx. 750 mm x 10° * 3 pairs of lashing rings (LC 5,000 daN) * Hardwood flooring approx. 30 mm thick Loading area: * Loading area with rear bevel approx. 1,000 mm x 8° * 5 pairs of fold-out lashing rings to the outside (LC 5,000 daN) Lsdjy Auhuepfx Akkshn * 3 pairs of fold-out lashing rings to the outside (LC 10,000 daN) * 1 pair of horizontal lashing rings at the front of the loading area (LC 10,000 daN) * Hardwood flooring approx. 48 mm thick, checker plate above the axles Two-piece steel ramps: * One pair of galvanized two-piece steel ramps, approx. 3,185 + 1,420 x 1,250 mm, with grating covering C40/5 (point load approx. 2.8 t on a surface of approx. 20 x 20 cm) * Ramp with hydraulically foldable ramp sections and hydraulic lifting system * Maximum load per pair: 30,000 kg Landing legs: * JOST landing legs (mechanical) with 2-speed gearbox for approx. 24 t lifting capacity (approx. 50 t test load) Axles: * BPW axles and suspension, 2 rigid axles, 1 steering trailing axle * Technical axle load: 12,000 kg each * Electromagnetic reverse lock activated via reverse gear and manually * Air suspension with raise/lower valve Tyres: * Tyres 235/75 R 17.5 3PMSF – brand at our discretion TPMS: * TPMS tyre pressure monitoring system according to ECE R 141 Brake system: * WABCO brake system compliant with EU regulations, with EBS-E (2S2M), without connection lines to the tractor unit Steel construction: * Steel construction made of high-strength fine-grain steels * Steel grades: S355J2+N/S355MC (yield strength 355 MPa), S690QL/S700MC (yield strength 690 MPa) Electrical system: * Electrical system according to EU regulations, LED lighting 24V ASPÖCK-NORDIK (ASS3) * All LED side marker lights flash with the indicator * ASPÖCK-UNIBOX on the front connection bar with 24N, 24S & 15-pin sockets according to ISO. 24N ISO-1185, 24S ISO-3731, 15-pin ISO-12098 Paintwork: * HRM metallisation of the entire vehicle chassis with ZINACOR 850 (85% zinc/15% aluminum) to guarantee optimum corrosion protection * Finishing coat: 2 layers 2K topcoat, solid colour RAL 3002 carmine red as per RAL system 841GL * Rear section metallised and painted RAL 9010 (pure white) * Rims in silver Included accessories: * One bracket for warning signs on the gooseneck and at the rear left and right, including socket * 1 spare wheel holder under the loading area, right in the direction of travel * 2" kingpin * One galvanized steel front wall * Yellow-red air couplings on the galvanized front connection bar * 4 wheel chocks with brackets on the bulkhead * 3 height wooden boards * Galvanized folding supports under the loading area bevel * Bracket for rotating beacon at rear of trailer * Height-adjustable tarpaulin structure – approx. 3,960 mm * Galvanized front wall with tensioning system for sliding curtains, height adjustable by approx. 400 mm * EDSCHA roof, sliding forward on aluminum roof girder profiles (screwed to front and rear wall) * 3 pairs of sliding stakes in the loading area * The body is hydraulically extendable to the left and right at the rear by approx. 750 mm * Sliding roof with pivoting portal crossbeam * Sliding curtain with approx. 700 mm reserve length, ratchet straps at approx. 600 mm intervals. Height O

Condition: new, empty load weight: 14,350 kg, maximum load weight: 53,450 kg, overall weight: 67,800 kg, axle configuration: > 3 axles, loading space length: 8,800 mm, loading space width: 2,540 mm, loading space height: 860 mm, suspension: air, tire size: 235/75 R 17,5, color: grey, Equipment: ABS, tail-lift, Gooseneck: - Gooseneck in SNT design for optimization of loading platform length, length approx. 3,700 mm - Rear gooseneck with bevel, approx. 1,000 mm x 10° - For tractor units: 6x2, 6x4, 8x4 short Loading Platform: - Extendable loading platform, length approx. 8,800 mm, with rear bevel approx. 500 mm x 10° - A recess in the loading platform and into the bevel to accommodate the excavator bucket arm, approx. 3,850 x 750 x 210/290 mm Two-Part Steel Ramps: Lhsdeya E A Nopfx Akkon - One pair of two-part steel ramps, length approx. 4,350 mm, width approx. 900 mm - Ramps with rubber covering - Ramps individually hydraulically movable approx. 235 mm outwards and approx. 215 mm inwards - "Super Grip" 25 mm rubber floor and steel plate floor approx. 5 mm as additional reinforcement on the platform bevel - Square climbing strips 20 x 30 mm, approx. every 200 mm on the outer frame of the ramp Axles, Suspension, and Tires: - BPW axles and suspension, 1st axle steerable, all other axles hydromechanically forced-steered - Technical axle load: 12,000 kg - 1st axle with electromagnetic reversing lock, activatable via reverse gear and manually - Air suspension with lift and lower valve - Tires 235/75 R 17.5 - TPMS tire monitoring system according to ECE R141 - TPMS tire pressure sensors installed in all wheels including spare wheels Surface Treatment: - Complete steel construction blasted automatically with a shot blast machine after welding - Second shot blasting with corundum for optimal coating adhesion - HRM metallization of the entire vehicle chassis with ZINACOR 850 (85% zinc / 15% aluminum) to ensure best corrosion protection - Final painting with 2 coats of 2K topcoat, single color in MB 7350 Novagrau Accessories Included: - Removable steel front wall, approx. 400 mm high - 3kW electro-hydraulic unit for controlling hydraulic operations, except for hydraulic winches - 1 spare wheel - Outer beam on gooseneck with mounting holes for bolted lashing rings - First hole approx. 200 mm from the front, then approx. every 400 mm - 2 pairs of screw-in lashing rings included - 1 pair of lying lashing rings at the rear of the gooseneck - 1 pair of removable ALU side walls on the gooseneck, approx. 400 mm high, anodized - 1 removable ALU rear wall on the gooseneck, approx. 400 mm high, anodized - Approx. 40 mm thick hardwood floor over the gooseneck, tread plate covering over the king pin - 2" king pin - Round NATO socket on the front connector strip - 4 wheel chocks - 1 intermediate table, approx. 300 mm wide - 1 pair of lashing rings on the front crossmember - 8 pairs of recessed lashing rings in the outer frame of the loading area, foldable outwards - Extensions (galvanized) extendable by approx. 230 mm per side - Wheel recesses with square climbing strips, 15 x 15 mm in front of the axles, continuously open up to the gooseneck crossmember, approx. 700 x 410 mm - Wheel recesses with square climbing strips, 15 x 15 mm between the first and second axles, approx. 1,480 x 700 x 410 mm - ALU covers for the wheel recesses, which can also be used as bridging elements for the extension or as extension beams - 1 pair of mechanical rear supports - Radio and cable remote control - Lift axle at the front axle - Square climbing strips 20 x 30 mm, approx. every 200 mm - Central lubrication system with 1 pump - Wabco Smart Board System - 4 warning signs, approx. 423 x 423 mm, extendable by approx. 400 mm

Condition: good (used), Year of construction: 2004, Extras Single extension Toolbox made of stainless steel Lashing points Spare wheel with bracket Mechanical landing gear Rear bumper with lighting Toolbox mounted on the gooseneck Lhjdpfxjzym T Uo Akksn Warning signs for overwidth Twist-lock for containers Kingpin 2.0 inches = Further information = Year of manufacture: 2004 Unladen weight: 10,800 kg Payload: 47,200 kg GVW: 58,000 kg Technical condition: good Visual condition: good Price: On request

Condition: new, maximum load weight: 45,115 kg, overall weight: 53,000 kg, axle configuration: 3 axles, Equipment: ABS, More vehicles can be found at [website address]. Excerpt from the equipment list. Complete equipment list available upon request. Loading area: Loading area with approximately 30 mm thick hardwood flooring. 8 pairs of lashing rings that can be folded outwards (LC 10,000 daN). Kingpin: JOST kingpins (mechanical) with a 2-speed gearbox for an approximate lifting capacity of 24 tons (approx. 50 tons test load). Tires: 385/65 R 22.5. TPMS tire pressure monitoring system according to ECE R 141. Data transmission to the tractor unit is via the standardized EBS interface according to ISO 11992. For correct display, the tractor unit must be able to transmit and display this data. Axles and suspension: BPW axles, technically rated at 10,000 kg each. 1st and 3rd axles are hydro-mechanically forced-steered and mounted on a turntable. 2nd axle is fixed. Air-suspended with lifting and lowering valve. Axle spanner. Braking system: Wabco braking system in accordance with EU regulations with EBS-E (4S3M) without connecting lines to the tractor unit. Lhjdpfj Ad Tdlsx Akken Electrical system: Electrical system in accordance with EU regulations, lighting 24 Volt ASPÖCK-NORDIK (ASS3). ASPÖCK-UNIBOX on the front connection bar with 24N, 24S & 15-pin sockets according to ISO. 24N ISO-1185 24S ISO-3731 15-pin ISO-12098. Steel structure: Steel structure made of high-strength fine-grain steels. Steel grades: S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa). Painting: Complete steel structure automatically blasted with a shot blasting system after welding. Second blasting with corundum for optimal adhesion of the coating system. Final coating with 2 layers of 2K topcoat, solid color in RAL 3002 Carmine Red according to the RAL 841GL system. Rear part is metallic and painted in RAL 9010 (pure white). Rims in silver. Coating tested in a salt spray test according to ISO 9227-NSS. Sealing of cavities with special wax. Accessories: Loading area with approximately 30 mm thick hardwood flooring. 2-inch kingpin. One galvanized steel front panel (EN12642-XL), approximately 1,200 mm high. Yellow-red air couplings on the galvanized front connection bar. 4 pieces of wheel chocks with holders on the front panel. Storage for approximately 1,000 mm lashing bars in the rear central beam. On the gooseneck and rear panel, one holder each on the left and right sides for warning signs including a socket. Yellow reflector tape according to EU regulations on the side and rear of the trailer. 10 pairs of lashing bar pockets for lashing bars approximately 100 x 50 mm in the outer frame of the loading area. European reflector signs (red-yellow) on the rear of the trailer. One holder for a rotating beacon on the rear of the trailer. One mud flap on the rear of the trailer. Manual and description on a USB stick. Speed stickers 80 km/h on the rear and both sides. Electro-hydraulic unit. 1 maneuvering coupling with reinforcement bolted to the end cross member. Load manometer for determining the axle loads including a load diagram. Central lubrication system BEKAMAX (Pico) with standard grease NLGI-2 and a removable guard around the pump. Follow-up steering from the front and rear using a cable remote control via push buttons, with single-axle steering control (without installation in the tractor unit). 7 pairs of galvanized lashing bars approximately 100 x 50 mm, approximately 1,000 mm high. 4 pairs of lashing bar strip rails, mounted transversely in the loading area, for las

Condition: used, axle configuration: 3 axles, first registration: 12/2005, loading space length: 8,700 mm, loading space width: 2,550 mm, suspension: air, tire size: 235/75/r17,5, wheelbase: 1,350 mm, Drivetrain Drive: Wheel Axle configuration Tyre size: 235/75/r17,5 Suspension: air suspension Rear axle 1: Double wheels Rear axle 2: Double wheels Rear axle 3: Double wheels; Steering Weights Empty weight: 10.280 kg Carrying capacity: 52.220 kg Ljdpfez Tqvxex Akkjhn GVW: 62.500 kg Functional Make of bodywork: FAYMONVILLE Dieplader Height of cargo floor: 90 cm

Condition: new, maximum load weight: 36,410 kg, overall weight: 48,000 kg, axle configuration: 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory with immediately and short-term available vehicles on our website. Extract from the equipment. Full equipment details available on request. GOOSENECK: * Gooseneck in SNT design for optimized loading platform length, length approx. 3,700 mm, rear with taper approx. 1,000 mm x 10° * For tractor units: 4 x 2, 6 x 2, and 6 x 4 * Steel front wall, removable, approx. 400 mm high * ASPÖCK-UNIBOX * 3 kW electro-hydraulic power unit for hydraulic functions, excluding hydraulic winches * Approx. 40 mm thick hardwood decking above the gooseneck * 2-inch kingpin * Gooseneck guide plate for the fifth-wheel plate, approx. 500 mm wide * Bracket at the rear of the gooseneck for ALU loading ramps * Round NATO socket on the front connection panel (Maeler & Kaege VG 96 917) * 4 wheel chocks with holders in front of the front wall * 1 pair of stake pockets recessed on the gooseneck for plug-in stakes approx. 100 x 50 mm (located on the inside of the chassis rail) EQUIPMENT: * Loading platform length approx. 8,800 mm, extendable version approx. 4,100 mm, with rear taper approx. 500 mm x 10° * A recess in the loading platform, extending into the tapered section to accommodate the excavator dipper stick, approx. 2,490 x 750 x 210/290 mm (L x W x H) * Pneumatic locking with conical locking bolts and reinforced locking positions, supply lines are protected inside the extendable beams and automatically adapt to the selected loading platform length * TPMS tire pressure monitoring system in accordance with ECE R 141 * BPW axles and suspension, 1st and 2nd axles rigid, 3rd axle steered * 3rd axle with electro-magnetic reverse lock, activated via reverse gear and manually * Technical axle load: each 12,000 kg with air suspension and raise/lower valve * 235/75 R 17.5 3PMSF twin tires. Manufacturer at our discretion * Mechanical landing legs with 2-speed gearbox and crank. JOST Module B – static test load = approx. 50,000 kg * Throughout the loading platform and between the axles, interrupted approx. 50 mm thick hardwood decking (increases coefficient of friction) * 1 intermediate table, approx. 300 mm wide, for the telescopic tube with large cross-section. Intermediate table with offset loading platform and extendable mounting rails for aluminum bridging elements * Platform locking with conically welded locking profiles every approx. 250 mm. Includes pre-tensioning plate * 1 pair of lashing rings on the front cross member (LC 10,000 daN) * 9 pairs of recessed lashing rings in the outer frame of the loading area, foldable outwards (LC 10,000 daN) * 1 pair of fixed wheel recesses in front of the axles, open up to the gooseneck cross member, approx. 700 x 410 mm (W x D) * Wheel recesses with 15 x 15 mm square climbing strips and widenings at the bottom (in case vehicle is equipped with extendable widenings) * 1 pair of fixed wheel recesses, approx. 1,480 x 700 x 410 mm (L x W x D), in the platform between 1st and 2nd axle Lodoy Auh Ijpfx Akkjhn * Wheel recesses with 15 x 15 mm square climbing strips and widenings at the bottom * Aluminum covers for the wheel recesses in front of the axles and between the 1st and 2nd axle, which can also be used as widening planks (if vehicle is equipped with extendable widenings) * Lockable aluminum elements installed on the extension tubes of the widenings * 1 pair of mechanical rear supports * 1st axle with traction aid * Sandblasting painted...

Condition: new, axle configuration: > 3 axles, permissible axle load (axle 1): 12,000 kg, permissible axle load (axle 2): 12,000 kg, permissible axle load (axle 3): 12,000 kg, total length: 17,700 mm, total width: 2,990 mm, total height: 3,810 mm, suspension: hydraulics, tire size: 245/70 R17.5 Double Fitted (143/141J), color: red, Equipment: tail-lift, Color: Red Payload: 100,250 kg Weights: King-Pin load: 38,000 kg Axle load: 12,000 kg Total axle load: 96,000 kg GVW: 134,000 kg Empty weight: 33,750 kg Loading capacity: 100,250 kg Axles: Axle brand: BPW ECO PLUS Hydraulic suspension 7-axle steering (Axle 2 rigid) First two axles liftable Drum brakes Brake SN 3020 for ABS, with sensors Tires: 245 / 70 R17.5 Double fitted Load index 143/141J Measurements: Length: 17,700 mm Lhedpjuu E Tiofx Akkon Extensions: 19,500 mm Max extended length: 37,900 mm Loading floor width: 3,990 / 3,450 mm Loading floor height: 1,050 mm +/- 150 mm Height: 3,815 mm Additional information: NATO plug Hydraulic foldable ramps Outriggers + planks for widening loading floor Electro-hydraulic pump for trailer functions Spare wheel + holder Working lamps Rear bumper with lights King-pin 2.0” Central lubrication Lashing rings Wooden loading floor Marker boards for oversize load Remote control = Further information = General information: Year of construction: 2024 Design year: 2024 Axle configuration: Tire size: 245/70 R17.5 Double Fitted (143/141J) Axle brand: BPW ECO PLUS Brakes: Drum brakes Suspension: Hydraulic suspension Rear axle 1: Double tires; Lift axle; Max. axle load: 12,000 kg; Steered; Tire tread depth left inside: 100%; Tire tread depth left outside: 100%; Tire tread depth right inside: 100%; Tire tread depth right outside: 100% Rear axle 2: Double tires; Lift axle; Max. axle load: 12,000 kg; Tire tread depth left inside: 100%; Tire tread depth left outside: 100%; Tire tread depth right inside: 100%; Tire tread depth right outside: 100% Rear axle 3: Double tires; Max. axle load: 12,000 kg; Steered; Tire tread depth left inside: 100%; Tire tread depth left outside: 100%; Tire tread depth right inside: 100%; Tire tread depth right outside: 100% Rear axle 4: Double tires; Max. axle load: 12,000 kg; Steered; Tire tread depth left inside: 100%; Tire tread depth left outside: 100%; Tire tread depth right inside: 100%; Tire tread depth right outside: 100% Rear axle 5: Double tires; Max. axle load: 12,000 kg; Steered; Tire tread depth left inside: 100%; Tire tread depth left outside: 100%; Tire tread depth right inside: 100%; Tire tread depth right outside: 100% Rear axle 6: Double tires; Max. axle load: 12,000 kg; Steered; Tire tread depth left inside: 100%; Tire tread depth left outside: 100%; Tire tread depth right inside: 100%; Tire tread depth right outside: 100% Rear axle 7: Double tires; Max. axle load: 12,000 kg; Steered; Tire tread depth left inside: 100%; Tire tread depth left outside: 100%; Tire tread depth right inside: 100%; Tire tread depth right outside: 100% Rear axle 8: Double tires; Max. axle load: 12,000 kg; Steered; Tire tread depth left inside: 100%; Tire tread depth left outside: 100%; Tire tread depth right inside: 100%; Tire tread depth right outside: 100% Weights: Empty weight: 33,750 kg Payload: 100,250 kg GVW: 134,000 kg Functional: Loading floor height: 105 cm Extendable superstructure: Yes Condition: Overall condition: very good Technical condition: very good Optical condition: very good Financial information: Price: On request

Condition: used, axle configuration: 3 axles, first registration: 09/2014, total length: 13,900 mm, total width: 2,540 mm, suspension: air, Additional information : Brand: FAYMONVILLE Model: Telemax Structure: platform ( platform L=13758 - 25258 mm extendable ) Year: 09.2014 VIN: YAFSR314000015733 Suspension: air Brakes: drum Dimensions: L/W: 13900 mm / 2540 mm Masses: full/empty: 75000 kg / 15810 kg EXTENDABLE / ALL AXLES STEERED Model year : 2014 Suspension type : air Brakes : Drum Liftable axle : Liftable axle Suspension type : air Brakes : Drum Steering : Steering Suspension type : air Brakes : Drum Steering : Steering = More information = Lsdpfx Akezwkp Iokjhn Year of construction: 2014 Suspension: air suspension Front axle: Lift axle Middle axle: Steering Rear axle: Steering Empty weight: 12.500 kg Carrying capacity: 46.500 kg GVW: 59.000 kg Please contact Deniss Urmaker, Mark Ševtšenko, Alejandro Goyeneche or Hesham Haddad for more information

Condition: new, maximum load weight: 48,930 kg, overall weight: 63,000 kg, axle configuration: > 3 axles, Equipment: ABS, You can find our complete vehicle inventory, including vehicles available immediately and in the short term, on our website. Excerpt from the equipment list. Complete equipment list available upon request. Gooseneck * with beveled front corners, approximately 45° and with rear bevel approximately 750 mm x 10° * 3 pairs of lashing rings (LC 5,000 daN) * Hardwood flooring, approximately 30 mm thick Loading platform * in a double-extendable design with rear bevel approximately 500 mm x 8° * 5 pairs of lashing rings, foldable outwards (LC 5,000 daN) * 4 pairs of lashing rings, foldable outwards (LC 10,000 daN) * 1 pair of lashing rings, horizontally at the front of the loading platform (LC 10,000 daN) * 1 intermediate table, approximately 250 mm * Recesses in the outer frame of the loading platform for attaching tension straps (LC 2,000 daN) * Hardwood flooring, approximately 48 mm thick, with diamond plate flooring over the axles Axles * BPW axles, hydro-mechanically forced steering * Technical axle load: 12,000 kg each * Air suspension with lifting and lowering valve Tires * 245/70 R 17.5 3PMSF, load index (146/146 F) * TPMS tire pressure monitoring system according to ECE R 141 Kingpin * JOST kingpins (mechanical) with a 2-speed gearbox for approximately 24 t lifting capacity (approximately 50 t test load) Braking system * according to EU regulations with EBS-E (4S3M) Steel structure * made of high-strength fine-grained steel * Steel grades: S355J2+N/S355MC (yield strength 355 MPa) * S690QL/S700MC (yield strength 690 MPa) Electrical system * according to EU regulations, lighting 24 Volt ASPÖCK-NORDIK (ASS3) * All LED side marker lights flash with the turn signal Lodpfxszlwm As Akkohn * ASPÖCK-UNIBOX on the connection strip at the front with 24N, 24S & 15-pin sockets according to ISO. 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Painting * Complete steel structure automatically blasted after welding using a blasting wheel system * Second blasting with corundum for optimal adhesion of the coating system * HRM metallization of the entire vehicle chassis with ZINACOR 850 (85% zinc/15% aluminum) to ensure the best corrosion protection * Final coating with 2 layers of 2K topcoat, solid color in RAL 3002 carmine red, according to the RAL 841GL system * Rims in silver. Rear part metallized and painted in RAL 9010 (pure white) * Metallic paint is not possible * Paint structure tested in the salt spray test according to ISO 9227-NSS * Sealing of cavities with special wax Including the following additional equipment 2 inch kingpin * Electro-hydraulic unit (± 45 kg) * Follow-up steering from the front and rear, controllable by means of a cable remote control via push buttons, with single-axle control (without installation in the central control unit) * One bracket for warning signs on the left and right of the gooseneck and on the rear panel, including socket * One bracket for a rotating beacon on the rear of the trailer * Aluminum side panels and rear panel on the gooseneck, pluggable, approximately 2,440 x 400 mm (L x H) * The rear galvanized stake pockets are removable. (Length of the superstructure approximately 2,560 mm) (± 46 kg) * A tool box, galvanized, integrated into the beveled gooseneck (± 47 kg) * 4 pairs of WADER container pockets in the loading platform for a 20', 2x 20', 40 or a 45' container (± 40 kg) * 7 pairs of stake pocket for stake pockets approximately 100 x 50 mm in the outer frame of the loading platform (± 21 kg) * Extensions, galvanized

Condition: new, maximum load weight: 47,300 kg, overall weight: 58,000 kg, axle configuration: > 3 axles, loading space length: 8,600 mm, total width: 2,540 mm, Equipment: ABS, You can find our complete range of vehicles, including those available immediately and at short notice, on our website. Excerpt from the equipment list. Full specifications available on request. Gooseneck: * Gooseneck with beveled front corners (approx. 45°) and rear bevel (approx. 750 mm x 10°) * 3 pairs of lashing rings (LC 5,000 daN) * Hardwood flooring approx. 30 mm thick Loading area: * Extendable loading platform with rear bevel (approx. 1,000 mm x 8°) * 5 pairs of outward-folding lashing rings (LC 5,000 daN) * 3 pairs of outward-folding lashing rings (LC 10,000 daN) * 1 pair of recessed lashing rings at the front of the loading platform (LC 10,000 daN) * Cutouts in the outer frame of the loading area for hooking tensioning straps (LC 2,000 daN) * Hardwood flooring approx. 48 mm thick; over the axles, diamond plate surface Landing legs: Lodpfjyvnfgsx Akkehn * JOST landing legs (mechanical) with 2-speed gearbox, 24t lifting capacity (50t test load) Tyres: * 235/75 R 17.5 3PMSF tyres, brand at our discretion Axles: * BPW axles, two rigid axles, two trailing steering axles, air-suspended, with drum brakes, lifting/lowering function * Steering axles with electromagnetically-activated reverse lock (via reverse gear or manually) * Axle tools Brake system: * WABCO brake system in accordance with EU regulations with EBS-E (4S3M), no connecting lines to the tractor unit Steel structure: * Steel construction from high-strength fine-grained steels * Steel grades: S355J2+N/S355MC (yield 355 MPa) S690QL/S700MC (yield 690 MPa) Electrical system: * Electrical system compliant with EU regulations, lighting 24 Volt ASPÖCK-NORDIK (ASS3) * ASPÖCK-UNIBOX on the front connection bar with 24N, 24S & 15-pin sockets (ISO standard: 24N - ISO 1185, 24S - ISO 3731, 15-pin - ISO 12098) Paintwork: * Premium and long-lasting corrosion protection of the standard shot-blasted welded frame guaranteed by a 2-component (2K) zinc-rich primer * High-quality 2-component (2K) single-color topcoat RAL 3002 Carmine Red * Rear section metallized and painted in RAL 9010 (Pure White) * Rims in silver Accessories: * Spare wheel holder in front of the bulkhead (without spare wheel) * 2 inch kingpin * Galvanized steel front wall approx. 400 mm high * Yellow-red air couplings on the galvanized front connection bar * Receptacle at the rear of the gooseneck for ALU loading ramps * Galvanized drop-down supports under the loading area bevel * Bracket for a revolving beacon at the rear of the trailer * Brackets left and right on the gooseneck and rear plate for warning signs including socket * TPMS tire pressure monitoring system compliant with ECE R 141 * Removable ALU sideboards and rear wall on the gooseneck, approx. 2,440 x 400 mm (L x H); rear galvanized insert posts are removable (body length approx. 2,560 mm) * Galvanized toolbox integrated in the beveled gooseneck * 3 pairs of WADER container locks in the loading platform for one 20' (30') or one 40' container * Sliding hook-in rails for ALU loading ramps at the rear of the vehicle * 6 pairs of pockets for plug-in posts, approx. 100 x 50 mm in the outer frame of the loading area * Galvanized extensions, extendable by approx. 230 mm per side * Lift axle on the front axle with TEBS E control based on current axle load and load status * 2 LED reversing lights mounted on the rear plate * 2 pairs of ferry-

Condition: new, axle configuration: 3 axles, permissible axle load (axle 1): 10,000 kg, permissible axle load (axle 2): 10,000 kg, permissible axle load (axle 3): 10,000 kg, loading space length: 29,000 mm, loading space width: 2,540 mm, loading space height: 2,850 mm, total length: 29,000 mm, total width: 2,540 mm, total height: 2,850 mm, suspension: air, tire size: 385/65-R22.5, Equipment: ABS, - BPW axles - EBS - Air suspension - Disc brakes - Central lubrication system NEW MAX210-Z-3AA-13.60-22.5-2.54, available directly from stock Technical data MAX210-Z-3AA-13.60-22.5-2.54 Total weight: 48,000 kg / Coupling pressure: 18,000 kg / Axle load: 30,000 kg / Tare weight: 11,456 kg / Payload approx.: 36,544 kg / Coupling height (laden): 1150–1250 mm / Turning radius: 2300 mm Loading area length: 13,600 mm / 2-way extendable (2 x 770 mm) to 2900 mm / Wheelbase: 1810 mm Technical description: Extendable loading area with pneumatic locking / A fixed intermediate table of ± 250 mm is located in the central box structure. / 8 pairs of lashing eyes that fold outwards (LC 5,000 daN) / 3 pairs of lashing eyes that fold outwards (LC 10,000 daN) / Recesses in the outer frame for attaching lashing straps (LC 2,000 daN) Tires: Tires 385/65 R22.5 (Brand: Goodyear) Tire pressure monitoring system (TPMS): TPMS according to ECE R 141 Axles: BPW axles with disc brakes, air-suspended with raising and lowering valve. All axles are hydromechanically steered. Technical axle load: 10,000 kg (ET 0) Braking system: WABCO braking system according to EU regulations with EBS-E system (2S2M), without connecting cable to the tractor. Steel structure: Steel structure made of high-quality fine-grain steel. Steel grades: S355J2+N/S355MC (Yield strength 355 MPa) / S690QL/S700MC (Yield strength 690 MPa) Electrical system: Electrical system according to EU regulations, lighting 24 V ASPÖCK-NORDIK (ASS3). ASPÖCK-UNIBOX on the galvanized connection strip at the front with 24N, 24S and 15-pin sockets. Connections according to ISO / 24N ISO-1185 / 24S ISO-3731 / 15-pin ISO-12098 Warning signs: Below the gooseneck and at the rear, left and right, holder for warning signs with socket. Options: • Maneuverability at the front and rear via cable remote control with PDC light control for axle alignment. (without mounting on the tractor) • Electro-hydraulic unit (approx. 45 kg) • 2 wheel chocks with holder on the partition wall • Kingpin 2" • Galvanized steel partition, approx. 1600 mm high. EN12642-XL • White reflector tape according to EU regulations over the entire length and width. Red at the rear. • EU marking plates (red-yellow) at the rear of the vehicle. • Holder for a rotating beacon at the rear of the vehicle. • Loading floor made of 30 mm thick hardwood, reinforced with omega profiles (approx. 298 kg). • 10 pairs of stake holder, approx. 100 x 50 mm, in the outer frame of the loading floor. • 1 spare wheel holder under the loading floor on the right. • BEKAMAX (Pico) central lubrication system with 2 pumps. Lhodpfe Aba Irjx Akken • 6 pairs of recesses in the loading floor for WADER container locks, for 1 x 20', 2 x 20', 1 x 40' or 1 x 45' container. • 5 pairs of stake profiles, mounted across in the loading floor, for stakes 100 x 50 mm • Galvanized storage compartment under the loading floor (2390 x 720 x 400 mm) • Rope hooks (8 mm), every approx. 500 mm below the edge profile of the gooseneck and the loading floor • Ladder, mounted on the left in the direction of travel • Stainless steel toolbox • LED lighting • 10 pairs of twist locks (100 x 50 mm, length 1000 mm) • 8 container General information Year of manufacture: 2026...

Condition: new, maximum load weight: 36,040 kg, overall weight: 53,000 kg, axle configuration: 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory with vehicles available immediately and in the short term on our website. Excerpt from the equipment list. Complete equipment list available upon request. Gooseneck: * Gooseneck in SNT design to optimize the loading area length, length approx. 3,750 mm * Gooseneck hydraulically raisable/lowerable and extendable * For tractor unit: 6 x 4 or 8 x 4 Low-bed: * Low-bed with external beams in an extendable SUPER LOW design, length approx. 8,000 mm * Low-bed with a fixed hardwood floor approx. 40 mm thick and mechanical locking system * The supply lines are protected in the extendable beams and automatically adjust to the respective low-bed length * 7 pairs of lashing rings that can be folded outwards (LC 10,000 daN) * 6 pairs of threaded blocks on the inner beam for mounting screw-on RUD rings Rear chassis: * Rear chassis with closed outer frame and diamond plate cover * Chassis with excavator bucket, which is closed in the rear half to accommodate the air tanks * 3 pairs of lashing rings that can be folded outwards (LC 5,000 daN) * 1 pair of lashing rings that can be folded outwards (LC 10,000 daN) * 1 pair of lashing rings, horizontally, at the front and rear of the chassis (LC 10,000 daN) Axles: * BPW axles and suspension, all axles hydro-mechanically forced-steered * Technical axle load: 12,000 kg each * Air suspension with lifting and lowering valve Tires: * Tires 245/70 R 17.5 3PMSF - at the manufacturer's choice. Load index (146/146F) Braking system: * WABCO braking system in accordance with EU regulations with EBS-E (2S2M) Paint: * HRM metallization of the entire vehicle chassis with ZINACOR 850 (85% zinc/15% aluminum) to ensure the best corrosion protection * Topcoat with 2 layers of 2K topcoat, solid color in RAL 3002 carmine red, according to the RAL 841GL system Includes accessories: Lhjdpfxsy Uwu Io Akkjn * 2-inch kingpin * One galvanized steel front bulkhead, approx. 400 mm high * Yellow-red air couplings on the galvanized connection strip at the front * Trailer steering, operable from the front and rear via cable remote control with push buttons, with single-axle steering control (without installation in the tractor unit) * Preparation for mounting screw-on container positioning for 1 x 20', 1 x 40' or 1 x 45' containers on the outer beams. Without container locking mechanisms * Hydraulic connections from the gooseneck to the low-bed with multi-coupling instead of screw couplings * Electro-hydraulic unit * Spiral cable for supplying the electro-hydraulic unit and/or the electric winch (approx. 35 mm², approx. 3.5 m long, max. 250A) between the semi-trailer and the tractor unit with plug connection (NATO-NATO) * Yellow reflector tape according to EU regulations on the side, on the extension and at the rear of the semi-trailer * On the gooseneck and at the rear, left and right, one bracket each for the warning signs, including a socket * Manual and description on a USB stick * Central lubrication system with 2 BEKAMAX (Pico) pumps with standard grease NLGI-2 and removable protection around the pumps * 7 pairs of threaded blocks between the lashing rings under the top chord on the outer beam for mounting screw-on RUD VLBG-4 rings * 2nd driving height, approx. 50 mm above the normal driving position, by means of manual operation * On the gooseneck, plug-in aluminum side panels and rear panel, approx. 2,440 x 400 mm (L x H). The rear, galvanized plug-in frames are removable (length of the superstructure

Condition: new, maximum load weight: 92,045 kg, overall weight: 126,000 kg, axle configuration: > 3 axles, Equipment: ABS, Excerpt from the equipment list Complete equipment upon request * 1 x Gooseneck MAX710-Neck-V-30-2.70 * Gooseneck with hydraulic lifting/lowering and extendable function * Length approx. 3,650 mm. For SZM 6x4 or 8x4 * Steel front panel, approx. 400 mm high * Plug-in aluminum side and rear panels on the gooseneck, approx. 400 mm high, in anodized finish * 3.5-inch kingpin * Truck hydraulic connection with flow control (20 l/min) * Incl. gantry for suspending the supply lines * The SZM tank must contain at least 80 l with MAX trailer couplings, otherwise the customer must provide the couplings ex works * BEKA-MAX central lubrication system for a gooseneck with standard grease NLGI-2 * TPMS tire pressure monitoring system * Two toolboxes INOX, approx. 855 x 340 x 390 mm, on the gooseneck, left and right (± 48 kg) * 1-cylinder Hatz diesel engine (Silent Pack) with electric starter and starter battery * Hydraulic connection lines between the power pack and the connection plate on the gooseneck * Radio remote control: operation of the power pack, start/stop of the diesel engine * Operation of the trailing axle, in addition to the cable remote control * with 2 LED indicator lights on the receiver for single-lane operation * Operation of raising/lowering the gooseneck * Operation of raising/lowering the suspension of the axle assemblies * Multicoupling hydraulic connections on the gooseneck * 1 LED work light, left and right, on the rear panel of the gooseneck, with separate on/off switch * Four warning boards, extendable by ± 2,000 mm, approx. 423 x 423 mm, with an LED position light and a mounting for a rotating beacon. (± 122 kg) Lhsdpfx Ajzzhfnekken * 1 x 3-axle compact front axle * MAX710 axle PA-F-3-19.5-1.36-2.85 * Hook connection at the front and rear * Length: approx. 3,560 mm * Axle width: approx. 2,850 mm * Front axle with a separate air connection for air suspension * BEKA-MAX central lubrication system for a 3-axle axle assembly with standard grease NLGI-2. * A 7-pole socket, left and right, at the rear of the front axle for the warning boards * TPMS tire pressure monitoring system according to ECE R 1411 * LED work lights, left and right, at the rear of the front axle with a separate on/off switch * Surface of the front axle with a sand-coated paint finish for slip resistance * Multicoupling hydraulic connections on the front axle * 1 x Low loader bridge: MAX710-Low-loader-BB-A-7.15-(430)-2.85 * Telescopic low loader bridge BB-A with drivable bridge hooks at the front and a bolt-on coupling at the rear * Basic width: approx. 2,850 mm Length: approx. 7,150 mm * Beam height: approx. 430 mm Beam width: approx. 1,350 mm * Loading height approx. 580 mm with ground clearance approx. 150 mm * 6 pairs of steel chequered plate with rubber matting approx. 1,000 mm, 1 pair approx. 500 mm (± 1,660 kg) * Possibility to screw in (ø approx. 40 mm) every approx. 500 mm on the outside of the top chord of the outer tube of the low loader bridge for screw rings (LC 16,000 daN) * Possibility to screw in M30 every approx. 1,000 - 1,200 mm on the outside of the inner tube of the low loader bridge for mounting screw rings (LC 10,000 daN) * Folding widening extensions with steel chequered plate, adjustable in width from approx. 2,850 mm to approx. 3,250 mm * TPMS tire pressure monitoring system * Pair of loose HeProLen plastic wheel chocks with climbing strips approx. 1,200 x 450 x 50/400 mm. (± 130 kg) * 2 pairs of screwable lashing rings M30 (LC 12,000 daN). (± 13 kg) * Ce

Condition: used, maximum load weight: 33,300 kg, overall weight: 42,000 kg, axle configuration: 3 axles, first registration: 09/2003, next inspection (TÜV): 01/2027, loading space length: 13,500 mm, loading space width: 2,500 mm, loading space height: 1,500 mm, total length: 13,600 mm, total width: 2,550 mm, total height: 3,200 mm, Equipment: ABS, Extendable semi-trailer, overall length adjustable from 7700 mm to 21300 mm, 9 stake pockets per side, 9 lashing points per side, all-round warning light / rear and center, extendable warning signs, JOST support jacks, central lubrication system, continuous underfloor box, ABS, EBS, SAF axle(s), last axle steered, drum brake system, air suspension with lifting and lowering mechanism, vehicle can be covered with advertising and/or lettering. SI86996 Our offer generally does not include a new TÜV inspection. If a new TÜV inspection is desired, we will be happy to provide you with a quote from our partner workshops! The vehicle can be covered with advertising and/or lettering. Our general terms and conditions of delivery and payment apply. We would be happy to prepare a financing or leasing offer for this item. Lhsdpfxezw Sgbo Akkjn Please contact us!

Condition: used, maximum load weight: 33,300 kg, overall weight: 42,000 kg, axle configuration: 3 axles, first registration: 09/2003, next inspection (TÜV): 01/2027, loading space length: 13,500 mm, loading space width: 2,500 mm, loading space height: 1,500 mm, total length: 13,600 mm, total width: 2,550 mm, total height: 3,200 mm, Equipment: ABS, Extendable semi-trailer, overall length adjustable from 7700 mm to 21300 mm, 9 stake pockets per side, 9 lashing points per side, all-round warning light / rear and center, extendable warning signs, JOST support jacks, central lubrication system, continuous underfloor box, ABS, EBS, SAF axle(s), last axle steered, drum brake system, air suspension with lifting and lowering mechanism, vehicle can be covered with advertising and/or lettering. SI86996 Our offer generally does not include a new TÜV inspection. If a new TÜV inspection is desired, we will be happy to provide you with a quote from our partner workshops! The vehicle can be covered with advertising and/or lettering. Our general terms and conditions of delivery and payment apply. Ljdezw Sguepfx Akkshn We would be happy to prepare a financing or leasing offer for this item. Please contact us!

Condition: new, empty load weight: 10,900 kg, maximum load weight: 37,100 kg, overall weight: 48,000 kg, axle configuration: 3 axles, loading space length: 9,600 mm, loading space width: 2,540 mm, loading space height: 890 mm, suspension: air, tire size: 235/75 R 17.5, color: grey, operation weight: 10,900 kg, Equipment: ABS, Gooseneck: -Gooseneck in SNT design to optimize the loading area length, length approx. 3,700 mm, with a bevel at the rear of approx. 1,000 mm x 6° -Technical fifth wheel load: 18,000 kg -For tractor units: 4 x 2 and 6 x 2 Loading area: -Loading area, length approx. 9,600 mm with a bevel at the rear of approx. 900 mm x 6° -Loading area can be raised and lowered hydraulically after the gooseneck, length approx. 3,000 mm, load capacity up to approx. 9,000 kg -Grating and sheet metal floor approx. 5 mm as additional reinforcement on the bevel of the loading area Ramps: -A pair of two-part AXS steel ramps with a length of approx. 4,675 mm and a width of approx. 900 mm -Grating floor Lhjdpouadk Njfx Akkon -Hydraulically hinged ramp tips -Ramps can be moved hydraulically by approx. 235 mm outwards and approx. 365 mm inwards -Painted sand coating on the outer frame of the ramp and on the ramp tip -Flashlights on the outside of the ramp tips with switch next to the ramp controls -Ramp secured in driving position using a quick release Axles, suspension and tires: -BPW axles and suspension, 1st and 2nd axle rigid, 3rd axle with self-steering -1st Axle with traction aid -Operation via the brake pedal in the tractor unit -Technical axle load: 12,000 kg -Air suspension with lifting and lowering valve -235/75 R 17.5 -TPMS tire pressure monitoring system in accordance with ECE R 141 -TPMS tire pressure monitoring sensors mounted in all wheels including spare wheels Braking system: -WABCO EBS-E brand braking system in accordance with EU regulations Paintwork: -Semi-trailer MB 7350 Nova gray Accessories included: -Bulkhead made of steel, plug-in, approx. 400 mm high -3 kW electro-hydraulic unit for controlling the hydraulic processes, with the exception of hydraulic cable winches -Guide plate from the gooseneck for the fifth wheel plate, approx. 500 mm wide -JOST module B - static test load = 50,000 kg -Continuous grating with 5 mm sheet metal underlay as additional reinforcement -Painted sand coating -Cutouts in the outer frame of the loading area and the lifting bed for hanging control valves for the hydraulic ramps on the right of the vehicle -2" kingpin -Central lubrication system with 1 pump, brand BEKAMAX -On the gooseneck 1 pair of plug-in aluminum side walls, approx. 400 mm high, anodized -Electric cable winch, approx. 5,400 kg pulling force, with radio remote control -Wire cable approx. 24 m long, cable ø approx. 9.5 mm, including cable pressure roller -WABCO Smart Board System -4 extendable warning signs, approx. 423 x 423 mm, extendable by approx. 400 mm

Condition: new, empty load weight: 17,250 kg, maximum load weight: 48,700 kg, overall weight: 66,000 kg, axle configuration: 3 axles, loading space length: 7,550 mm, loading space width: 2,480 mm, loading space height: 375 mm, tire size: 245/70 R 17.5, color: grey, operation weight: 17,250 kg, Equipment: ABS, Gooseneck: -Gooseneck in SNT design for optimizing the loading platform length, length approx. 3,750 mm -Gooseneck hydraulically extendable/retractable and lowerable -For semi-trailer tractors: 6 x 4 and 8 x 4 (or 6 x 4 with optional 1-axle dolly) Lowboy: -Lowboy with external beams, designed as a telescoping boiler bridge with low construction and front extension -Length x width approx. 7,550 mm x 2,740 mm -Mechanical locking of the extension Chassis: -Rear chassis with closed outer frame -Diamond-plate surface and continuous prism-shaped excavator well approx. 1,450/900 x 505 mm, open at the rear Axles, suspension and tires: Lsdpfoh Hm Tzox Akkehn -“PENDEL-AXLE”, all axles hydromechanically forced steered -Hose rupture valve on the axle equalizing cylinder with automatic RESET function -Hydraulic cylinders with shut-off valves and quick-release couplings for securing in the raised position -Final coat of axles with 2 layers of 2-component paint in a single color, painted in “FAY-Gray-34-0260” -Technical axle load 12,000 kg -Hydraulic axle equalization -245/70 R 17.5 Accessories: -Steel front wall, plug-in type, approx. 400 mm high -4 pieces of chock blocks -Gooseneck with a removable cover closed at the rear upper area -1 pair of steel ramps with cleats and fastening bolts for bridging the pick-up hooks of the lowboy -The ramps can be positioned above or between the hooks -Mounting options for the steel access ramps at the rear between the outer beams of the gooseneck -A locking point approx. every 1,000 mm on the extension -1 lashing ring on the left and right on the front crossbeam -Connection bar for supply lines to the semi-trailer tractor, mounted at the height of the outer frame profile -6 pairs of threaded blocks on the outside of the inner beams of the loading platform for mounting screw-on rings M24 -6 pairs of recessed lashing rings on the outside of the outer beams of the loading platform, foldable inwards and outwards -1 pair of threaded blocks at the front and rear on the outer beams of the loading platform for mounting screw-on rings M24 -Mounting rail for loose ALU ramps on the end cross member of the vehicle -Central lubrication system with 2 pumps, brand BEKAMAX -Trailing steering from the front and rear, operable via cable remote control, with single-axle steering control -3 kW electro-hydraulic unit for controlling the hydraulic operations, with the exception of hydraulic winches -Removable loading floor (galvanized) can be inserted in 3 elements between the outer beams with hardwood surface -Folding widening elements, approx. 230 mm per side -Widening boards, loose, with steel edging -4 warning signs approx. 423 x 423 mm -Radio remote control for operating the trailing steering -3.5" kingpin -Anti-slip strips on the left slope of the gooseneck -Hydraulic connections from the gooseneck to the lowboy with multi-coupling instead of screw couplings -Guide plate from the gooseneck for the fifth wheel plate, approx. 800 mm wide -1 spare wheel with mounting adapter -Parking position on the gooseneck for the warning signs when not in use -2 pairs of pole pockets embedded in the outer frame of the chassis, for plug-in poles approx. 100 x 50 mm -Bucket arm recess of the rear chassis closed at the rear with a plug-in plate -Color of the semi-trailer MB 7350 Novagrau

Condition: new, maximum load weight: 25,645 kg, overall weight: 38,000 kg, axle configuration: 2 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete stock of immediately and soon-to-be available vehicles on our website. Excerpt from equipment specification. Complete specification available on request. Load area: - Low-bed design with central beam, extendable version, approx. 6,750 mm in length - 5 pairs of fold-out external lashing rings (LC 5,000 daN) - 1 pair of fold-out external lashing rings (LC 10,000 daN) - 1 pair of flat-mounted lashing rings at the rear of the loading platform (LC 10,000 daN) Gooseneck: - Hydraulic lifting/lowering gooseneck, detachable Rear chassis: - Short rear chassis with closed outer frame and checker plate covering - Chassis with excavator trough, closed in the rear half for housing the air tanks - 2 pairs of fold-out external lashing rings (LC 5,000 daN) - 1 pair of fold-out external lashing rings (LC 10,000 daN) - 1 pair of flat-mounted lashing rings at the rear of the chassis (LC 10,000 daN) Axles: - BPW axles, hydro-mechanically forced steering - Air suspension with raise/lower control valve Tyres: Lodoxf Silepfx Akkohn - Tyres 245/70 R 17.5, 3PMSF - TPMS: Tyre Pressure Monitoring System according to ECE R 141 Brake system: - Wabco braking system in accordance with EU regulations with EBS-E (2S2M) Paintwork: - High-quality single-tone 2-component (2K) top coat in RAL 3000 Flame Red Including the following additional equipment: - 2 kingpins - Galvanised steel front wall, approx. 400 mm high - Remote steering from front and rear, operated by cable remote control with push buttons, including single tracking control for the axles (no installation in the tractor unit) - Electro-hydraulic unit - Axle load gauge including load diagram - On the gooseneck, removable aluminium side walls and rear wall, approx. 2,440 x 400 mm (L x H). Rear galvanised stake pockets are removable. (Body length approx. 2,560 mm) - Separate air connection with air gun on the gooseneck - 2 work lights with switch on the trailer, mounted on the left and right of the gooseneck platform - 1 INOX toolbox, approx. 1,350 x 400 x 400 mm, on the gooseneck - 6 pairs of stake pockets for insertable posts approx. 100 x 50 mm in the outer frame of the load area, 2 pairs in the chassis outer frame - Galvanised, extendable width extensions approx. 230 mm per side - Hydraulic connections from gooseneck to low bed with multi-coupling (instead of screw couplings). No seal guarantee included. - Central lubrication system with 2 BEKAMAX (Pico) pumps, standard NLGI-2 grease, with removable protection around the pump - 2 pairs of WADER container locks on the loading area, for 1x20' container - 1 removable galvanised intermediate table with 1 pair of WADER container locks - 1 pair of steel ramps for bridging the low bed’s hook mountings - Anti-slip sand-coated layer painted on the load area - HRM Metallisation (High Resistance Metallisation)

Condition: excellent (used), axle configuration: 2 axles, permissible axle load (axle 1): 11,200 kg, permissible axle load (axle 2): 11,200 kg, first registration: 02/2019, total length: 13,050 mm, total width: 2,540 mm, total height: 3,650 mm, suspension: air, tire size: 235/75R17,5, color: green, = Additional options and accessories = - Air suspension = Notes = Faymonville F-S42-1AAA. Year of manufacture: 2019. 11.2-ton SAF axles. Tare weight: 10,400 kg. Payload: 37,000 kg. Max. total weight: 47,400 kg. Kingpin load: 25,000 kg. Hydraulic connection according to NATO standard. EBS, ABS, ALB. Winch (defective). Toolbox on the gooseneck. Hydraulic bridge (connection between loading platform and gooseneck): - Length: 3000 mm. Floor with longitudinal slots. Forced steering (2 steering axles). Air suspension. Hydraulic ramps (2-part): - Length: 2800 + 1700 mm. - Hydraulic width adjustment (left/right). Hydraulic rear support (2-point). Tires: 235/75R17.5 (tread depth 80 %). Dimensions: Gooseneck: Ljdpjz Av Efjfx Akkjhn L: 3700 mm. W: 2500 mm. H: 1400 mm. Kingpin height: 1150 mm. Loading platform: L: 9150 mm. W: 2550 mm. H: 900 mm. Overall dimensions of the semi-trailer: L: 13,050 mm. W: 2550 mm. H: 3650 mm. German semi-trailer! ID No.: 677. Heinhuis's general terms and conditions apply to all advertisements, offers, and quotations from Heinhuis, as well as to all contracts concluded by Heinhuis and the negotiations preceding them. By making any form of contact, you accept the validity of Heinhuis's general terms and conditions and declare that you have taken note of these conditions. Our prices are net export prices. = Further information = General information Year of construction: 2019 Axle configuration Tire size: 235/75R17.5 Suspension: Air suspension Rear axle 1: Twin tires; Max. axle load: 11,200 kg; Steered; Tire tread depth left inside: 80%; Tire tread depth left outside: 80%; Tire tread depth right inside: 80%; Tire tread depth right outside: 80% Rear axle 2: Twin tires; Max. axle load: 11,200 kg; Steered; Tire tread depth left inside: 80%; Tire tread depth left outside: 80%; Tire tread depth right inside: 80%; Tire tread depth right outside: 80% Weights Tare weight: 10,400 kg Payload: 37,000 kg GVW: 47,400 kg Functional Height of loading platform: 90 cm Condition Technical condition: very good Optical condition: very good = Company information = For more information:

Condition: new, empty load weight: 12,800 kg, maximum load weight: 36,200 kg, overall weight: 49,000 kg, axle configuration: 2 axles, loading space length: 6,850 mm, loading space width: 2,550 mm, loading space height: 375 mm, tire size: 245/70 R 17.5, color: grey, operation weight: 12,800 kg, Equipment: ABS, Gooseneck: - Gooseneck in SNT design to optimize the loading area length, length approx. 3,750 mm - Gooseneck hydraulically raised/lowered and removable - Technical fifth wheel load: 25,000 kg - For tractor units: 4 x 2, 6 x 2, and 6 x 4 Loading area: - Low bed with external supports, designed as a telescopic tank bridge in a low construction with a front extension - Length 6,850 mm x Width 2,540 mm - One locking point approximately every 1,000 mm on the extension Rear chassis: - Rear chassis with closed outer frame with checker plate cover and continuous prism excavator trough approx. 1,250/700 x 505 mm, open at the rear Axles, suspension, and tires: - "PENDEL-AXLE", all Hydro-mechanically forced-steered axles - Hose rupture valve on the axle balancing cylinder with automatic reset function - Hydraulic cylinder with shut-off valves and pins for securing in the raised position - Final axle painting with two coats of 2-component acrylic paint in a single color "FAY-Gray-34-0260" Lodjvy Edcepfx Akkehn - Technical axle load: 12,000 kg - Hydraulic axle balancing - Tires: 245/70 R 17.5 - TPMS tire pressure monitoring system in accordance with ECE R 14 - TPMS tire pressure monitoring sensors installed in all wheels, including spare tires Accessories included: - Steel bulkhead, plug-in, approx. 400 mm high - 3 kW electro-hydraulic unit for controlling the hydraulic processes, with the exception of hydraulic cable winches - One spare tire with mounting adapter - Gooseneck outer support with mounting holes for screwable lashing rings -Slidable aluminum side walls on the gooseneck, approx. 400 mm high, anodized -Slidable aluminum rear wall on the gooseneck, approx. 400 mm high, anodized -Checker plate covering above the gooseneck -Gooseneck guide plate for the fifth wheel plate, approx. 500 mm wide -Illuminated control panel on the gooseneck with on/off switch -Hydraulic crossbar for supporting the gooseneck on the tractor unit or a dolly -2" kingpin -Anti-slip sticker on the left slope of the gooseneck -Gooseneck closed at the rear upper area with a removable cover -4 chocks with brackets -Hydraulic connections from the gooseneck to the drop bed with multi-coupling instead of screw couplings -1 pair of steel ramps with climbing rails and fastening bolts for bridging the drop bed's hooks -The Ramps can be installed over or between the hooks. -Attachment option for the steel loading ramps at the rear between the outer supports of the gooseneck. -Prepared for screw-on container holders for 1x20f on the outer support. -Mechanical bolt-and-lug coupling from the low bed to the chassis, for replacing the loading area or installing extension supports. -With electro-pneumatic-hydraulic couplings. -The outer supports of the low bed are provided with a painted layer of sand as a slip protection. -Removable loading floor (galvanized) in 3 elements, insertable between the outer supports with hardwood flooring. -Foldable extensions, by approximately 230 mm per side. -Hanging rail at the front of the rear chassis to the low bed for loose loading ramps. -2 pairs of stake pockets recessed into the outer frame of the chassis, for plug-in stakes approx. 100 x 50 mm. -Hanging rail for loose Aluminum docking ramps on the vehicle's end crossbar -Central lubrication system with 2 pumps -Wireless and cable remote control -4 warning signs, approximately 423 mm x 423 mm extendable -Extensive lashing positions

Condition: new, maximum load weight: 90,700 kg, overall weight: 126,000 kg, axle configuration: > 3 axles, total width: 2,850 mm, Equipment: ABS, You can find our complete range of vehicles, including those available immediately or at short notice, on our website. Extract from the specifications. Complete equipment list available upon request. Gooseneck: Gooseneck hydraulically liftable/lowerable and detachable. Length approx. 3,650 mm. For tractor units: 6x4 or 8x4 3-axle compact front bogie: * Hook mounts at the front and rear. Length: approx. 3,560 mm * Chassis width: approx. 2,850 mm Lodew Tgp Dspfx Akkshn Lowbed: * Lowbed ATX-A with telescopic longitudinal beams in low design with fixed hardwood floor approx. 50 mm thick * With drive-over bridging hooks at the front and pin-lug coupling at the rear * Base width: approx. 2,850 mm, Length: approx. 7,150 mm, Beam height: approx. 330 mm, Beam width: approx. 750 mm * Loading height approx. 480 mm with ground clearance approx. 150 mm 5-axle rear bogie: * Mechanical pin-lug coupling for mounting a lowbed at the front, rear end traverse at the back * Chassis width: approx. 2,850 mm * Chassis length: approx. 6,840 mm * Pendle axle 3-axle front bogie: * PENDLE-AXLE, all axles hydro-mechanically forced steered * Hose rupture valve on axle compensation cylinder with automatic RESET function * Hydraulic cylinders with shut-off cocks and lock pins for securing in raised position * Final painting of axles with 2 coats of 2-component paint, single color in MB7350 Novagrau * Technical axle load: 14,640 kg each (62 km/h) * Hydraulic axle compensation * Front bogie tires: 12 x manufacturer’s choice (M+S) 285/70 R19.5, load index 150/148J 5-axle rear bogie: * PENDLE-AXLE, all axles hydro-mechanically forced steered * Hose rupture valve on axle compensation cylinder with automatic RESET function * Hydraulic cylinders with shut-off cocks and lock pins for securing in raised position * Final painting of axles with 2 coats of 2-component paint, single color in MB7350 Novagrau * Technical axle load: 14,640 kg each (62 km/h) * Hydraulic axle compensation * Rear bogie tires: 20 x manufacturer’s choice (M+S) 285/70 R19.5, load index 150/148J Paintwork: * HRM metallization of the entire vehicle chassis with ZINACOR 850 (85% zinc/15% aluminum) to ensure optimal corrosion protection * Final coat with 2 layers of 2-component topcoat, single color in RAL 3002 Carmine Red, according to RAL system 841GL Includes accessories: * Steel front bulkhead, approx. 400 mm high * Plug-in ALU side and rear boards on the gooseneck, approx. 400 mm high, anodized finish * 3.5 kingpin * BEKA-MAX central lubrication for one gooseneck * Multi-coupling hydraulic connections at the gooseneck * Front bogie with a separate air connection for pneumatic screwdriver * BEKA-MAX central lubrication for a 3-axle bogie * Preparation for mounting of bolt-on container locks for 1 x 20' or 1 x 30' containers on the outer beams * Without container locks * Mounts for foldable extensions outside on the outer beams of the loading area * One 7-pin socket left and right, front and rear on the rear bogie for warning signs * BEKA-MAX central lubrication for a 5-axle bogie * Socket on the rear bogie for the cable remote control of the steering override * Rear bogie with trough * 2 LED reverse lights mounted on the rear panel * European reflector panels (red-yellow) at the rear * One mud flap at the rear * One LED beacon with bracket left and right on the rear traverse * Two INOX toolboxes 855 x 340 x 390 mm on the gooseneck, left and right * 1-cycle

Condition: new, maximum load weight: 36,500 kg, overall weight: 48,000 kg, axle configuration: 3 axles, Equipment: ABS, You can find our complete vehicle inventory, including vehicles available immediately and in the short term, on our website. Excerpt from the equipment Complete equipment available upon request GOOSENECK * Designed in SNT to optimize the loading area length * Length approximately 3,700 mm, with a rear slope of approximately 1,000 mm x 6° For SZM: 4 x 2 and 6 x 2 * ASPÖCK-UNIBOX Grid floor with 5 mm sheet metal reinforcement on the gooseneck and the rear slope * 2-inch kingpin * Guide plate from the gooseneck for the fifth wheel plate, approximately 500 mm wide, round * NATO socket on the connection strip at the front on the gooseneck * 1 pair of pluggable aluminum side panels, approximately 400 mm high, in anodized design * 1 LED work light each on the left and right, mounted at the top of the front wall * Controlled via on/off switch (operation of the work lights from the SZM is not possible in this case) LOADING AREA * Length approximately 9,600 mm, with a rear slope of approximately 900 mm x 6° * Loading area after the gooseneck can be hydraulically raised and lowered, length approximately 3,000 mm Lodpszzhfuofx Akkshn * Load capacity up to approximately 9,000 kg on the lifting platform and the loading area, continuous grid floor with approximately 5 mm sheet metal underlay as additional reinforcement, designed for point load TIRES * 235/75 R 17.5 3PMSF, twin tires, manufacturer of our choice * TPMS tire pressure monitoring system in accordance with ECE R 141 AXLES * BPW axles and suspension * 1st and 2nd axles rigid * 3rd axle with trailing steering * 3rd axle with electro-magnetic reverse lock, activated via reverse gear and manually * 1st axle with start-assist * Technical axle load: 12,000 kg each AIR SUSPENSION * with raising and lowering valve HYDRAULIC LOADING RAMPS * 1 pair of two-piece AXS steel ramps with grid floor and a length of approximately 4,920 mm and a width of approximately 900 mm * Hydraulically foldable ramp tips, ramps can be individually moved hydraulically outwards by approximately 235 mm and inwards by approximately 365 mm * Flashing lights on the outer sides of the ramp tips, with a switch next to the ramp control * Ramp securing in driving position by means of a quick-release fastener * Painted sand coating on the outer frame of the ramp as well as on the ramp tip * Mechanical supports in drop tube design on the sides of the ramps to support when docking with loading ramps * Control valves for the hydraulic ramps on the right side of the vehicle BRAKE SYSTEM * From WABCO EBS-E according to EU regulations SURFACE TREATMENT * HRM metallization of the entire vehicle chassis with ZINACOR 850 (85% zinc / 15% aluminum) to ensure the best corrosion protection PAINTING * Semi-trailer carmine red (RAL 3002) * Rims silver gray, side panels aluminum natural * Wheel hubs according to axle manufacturer, lamp sign pure white (RAL 9010) EQUIPMENT * Front wall made of steel, pluggable, approximately 1,600 mm high * Including connection strip for supply lines to the SZM, mounted approximately 1,000 mm from the lower edge of the outer frame profile * Possibility to attach lashing chains on the inside of the front wall on the left and right * Including aluminum tray underneath on the left and right for storing chains or lashing straps behind the front wall, approximately 12 mm thick DELIGNIT surface, screwed on * 2 pairs of screwable lashing rings additionally (LC 5,000 daN) * Electric winch, approximately 5,400 kg pulling force, with

Condition: new, empty load weight: 15,900 kg, maximum load weight: 63,500 kg, overall weight: 68,000 kg, axle configuration: > 3 axles, loading space length: 12,700 mm, loading space width: 2,740 mm, loading space height: 860 mm, suspension: air, tire size: 235/75/r17,5, color: grey, operation weight: 52,100 kg, Equipment: ABS, Gooseneck: Gooseneck in SNT design to optimize the loading area length, length approx. 3,300 mm, rear with bevel approx. 1,000 mm x 10° Technical fifth-wheel load: 23,000 kg For SZM: 6x2, 6x4 and 8x4 Cargo bed: Loading area in extendable design, length approx. 9,400 mm with bevel at the rear approx. 500 mm x 10° A recess in the loading area and protruding into the chamfer to accommodate the excavator dipper stick approx. 3,850 x 950 x 210/290 mm Pneumatic locking with conical locking bolt and reinforced locking positions, the supply lines are protected in the extendable beams and automatically adjust to the respective loading area length Axles and tires: BPW axles and suspension, 1st axle rigid, all other axles hydro-mechanically forced steered Technical axle load: 12,000 kg Air suspension with lifting and lowering valve Axle tool 235/75 R 17.5 3PMSF dual tires Load index 143/141J (144/144F) Two-piece steel ramps: A pair of two-piece steel ramps with a length of approx. 4,350 mm and a width of approx. 900 mm Hardwood decking Hydraulically hinged ramp tips Ramps can be moved individually hydraulically by approx. 235 mm outwards and approx. 215 mm inwards Brake system: WABCO EBS-E brake system in accordance with EU regulations Sockets and lighting: 24-volt lighting system Full metallization: Complete HRM metallization with ZINACOR 850 to ensure the best corrosion protection Surface treatment: Complete steel structure automatically blasted after welding with wheel blast cleaning Second blasting with corundum for optimum adhesion of the coating system Final coating with 2 layers of 2-component paint in a single color in nova grey, followed by sealing of the cavities with special wax Rims in silver gray Steel construction: Steel construction made from high-strength fine-grain steels Steel grades: S355J2+N/S355MC S690QL/S700MC Accessories: Steel end wall, pluggable, approx. 400 mm high Connection strip for supply lines to the SZM Spiral cable for supplying the electro-hydraulic unit and/or the electric cable winch between the trailer and SZM with plug Electro-hydraulic unit for controlling the hydraulic processes, with the exception of hydraulic cable winches Outer beam of the gooseneck with fastening holes for screwable lashing rings The first hole approx. 200 mm from the front, then approx. every 400 mm One fastening hole in the rear upper area of the gooseneck outer beam for a screwable lashing ring Approx. 40 mm thick hardwood covering over the gooseneck, checker plate covering over the kingpin Guide plate from the gooseneck for the fifth wheel plate, approx. 500 mm wide Continuous, approx. 50 mm thick hardwood planking on the loading area, interrupted between the axles Locking of the cargo bed with conically welded locking profiles every 250 mm, including pretensioning plate Ljdsmfqi Iepfx Akkshn Slotted holes for attachable and movable bridging elements: on the fixed part behind the gooseneck on the front of the cargo bed 1 movable intermediate table, for the large cross-section extension tube Control valves for the hydraulic ramps on the right-hand side of the vehicle Central lubrication system with 1 pump, with standard grease according to NLGI-2 Radio remote control for operating the steering, in addition to the cable remote control, with 2 indicator lights on the receiver as single-track control

Condition: used, maximum load weight: 37,150 kg, overall weight: 48,000 kg, axle configuration: 3 axles, first registration: 04/2026, next inspection (TÜV): 04/2027, Equipment: ABS, You can find our complete vehicle inventory with vehicles available immediately and in the short term on our website. Excerpt from the equipment list. Complete equipment available upon request. Gooseneck * with angled front corners approximately 45° and rear slope approximately 750 mm x 10° * 3 pairs of lashing rings (LC 5,000 daN) * Hardwood flooring, approximately 30 mm thick, extendable loading platform Loading platform * extendable design with rear slope approximately 1,000 mm x 8° * 6 pairs of lashing rings that can be folded outwards (LC 5,000 daN) * 3 pairs of lashing rings that can be folded outwards (LC 10,000 daN) * 1 pair of lashing rings lying horizontally at the front of the loading platform (LC 10,000 daN) * Recesses in the outer frame of the loading platform for attaching lashing straps (LC 2,000 daN) * Hardwood flooring, approximately 48 mm thick, diamond plate flooring over the axles Ledsz N Nwyjpfx Akkshn Kingpin supports * JOST kingpin supports (mechanical) with 2-speed gearbox for approximately 24 t lifting capacity (approximately 50 t test load) Tires * 235/75 R 17.5 3PMSF * TPMS: TPMS tire pressure monitoring system according to ECE R 141 * Data transmission to the tractor unit takes place via the standardized EBS interface according to ISO 11992. * For correct display, the tractor unit must be able to transmit and display this data. Axles * BPW axles and suspension, 2 fixed axles, 1 steerable axle * Technical axle load: 12,000 kg each * Electro-magnetic parking brake activated via reverse gear and manually Air suspension * with lifting and lowering valve Braking system * in accordance with EU regulations with EBS-E (2S2M) without connecting lines to the tractor unit Steel construction * made of high-strength fine-grained steels * Steel grades: S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa) Painting * Complete steel construction automatically blasted with a shot blasting system after welding * Second blasting with corundum for optimal adhesion of the coating system * Final painting with 2 layers of 2K topcoat * solid color in RAL 3002 carmine red * in accordance with the RAL system 841GL * Rims in silver gray * Rear section metallic and in RAL 9010 (pure white) * Paint structure tested in the salt spray test according to ISO 9227-NSS * Sealing of cavities with special wax Electrical system * in accordance with EU regulations * Lighting 24 Volt ASPÖCK-NORDIK (ASS3) * ASPÖCK-UNIBOX on the connection bar at the front with 24N, 24S & 15-pole sockets in accordance with ISO. 24N ISO-1185 24S ISO-3731 15-pole ISO-12098 Included accessories * Axle tool * 2-inch kingpin * One galvanized steel front wall, approximately 400 mm high * One spare wheel holder in front of the front wall * Yellow-red air couplings on the galvanized connection bar at the front * Mounting in the rear area of the gooseneck for aluminum loading ramps * Galvanized folding supports under the slope of the loading platform * One mounting for warning signs on the gooseneck and on the rear panel, left and right * including socket loadometer for determining the axle loads including load diagram * Aluminum side walls and rear wall on the gooseneck, pluggable, approximately 2,440 x 400 mm (L x H) * The rear galvanized locking strips are removable. (Length of the superstructure approx. 2,560 mm) * A toolbox galvanized, integrated in the angled gooseneck * 3 pairs of WADER container pockets in the loading platform for a 20' (30') or a 40' cont

Condition: used, color: red, Year of construction: 2018, Faymonville F-S42-2GXX. Year: 2018. 12 tons Pendel-X axles. Max. weight: 49,000 kg. Kingpin load: 25,000 kg. 5.5 meters extendable. 2 x 25 cm widened, including widening mechanism. Zinc-coated. Hydr. detachable gooseneck. Aluminum boards on the neck. Hydr. suspension. Radio remote control. Excavator bridge: 3050 mm x 700 mm. 3 detachable floorboards. Hydraulic system on the trailer operates on NATO electricity. Dimensions: Neck: Lhedpszyfzwsfx Akksn L: 3700 mm. W: 2500 mm. H: 1500 mm. Kingpin height: 1250 mm. Floor: L: 6850 mm. W: 2550 mm. H: 400 mm. Floor thickness: 230 mm. Rear of trailer: L: 3050 mm. W: 2550 mm. H: 950 mm. Tires: 245/70R17.5, 60% tread. ID No.: 494. The General Terms and Conditions of Heinhuis apply to all advertisements, offers, and quotations by Heinhuis, all agreements entered into by Heinhuis, and the negotiations preceding them. By any form of response, you accept the applicability of the General Terms and Conditions of Heinhuis and declare that you have taken note of these General Terms and Conditions. Our prices are export net prices. = Further Information = Year of manufacture: 2018 GVW: 49,000 kg Extendable superstructure: Yes = Company Information = For more information: