Used Faymonville Open Flatbed Semitrailers for sale (144)

Condition: new, maximum load weight: 36,410 kg, overall weight: 48,000 kg, axle configuration: 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory with immediately and short-term available vehicles on our website. Extract from the equipment. Full equipment details available on request. GOOSENECK: * Gooseneck in SNT design for optimized loading platform length, length approx. 3,700 mm, rear with taper approx. 1,000 mm x 10° * For tractor units: 4 x 2, 6 x 2, and 6 x 4 * Steel front wall, removable, approx. 400 mm high * ASPÖCK-UNIBOX * 3 kW electro-hydraulic power unit for hydraulic functions, excluding hydraulic winches * Approx. 40 mm thick hardwood decking above the gooseneck * 2-inch kingpin * Gooseneck guide plate for the fifth-wheel plate, approx. 500 mm wide * Bracket at the rear of the gooseneck for ALU loading ramps * Round NATO socket on the front connection panel (Maeler & Kaege VG 96 917) * 4 wheel chocks with holders in front of the front wall * 1 pair of stake pockets recessed on the gooseneck for plug-in stakes approx. 100 x 50 mm (located on the inside of the chassis rail) EQUIPMENT: * Loading platform length approx. 8,800 mm, extendable version approx. 4,100 mm, with rear taper approx. 500 mm x 10° * A recess in the loading platform, extending into the tapered section to accommodate the excavator dipper stick, approx. 2,490 x 750 x 210/290 mm (L x W x H) * Pneumatic locking with conical locking bolts and reinforced locking positions, supply lines are protected inside the extendable beams and automatically adapt to the selected loading platform length Nledpfey Auh Iox Aiash * TPMS tire pressure monitoring system in accordance with ECE R 141 * BPW axles and suspension, 1st and 2nd axles rigid, 3rd axle steered * 3rd axle with electro-magnetic reverse lock, activated via reverse gear and manually * Technical axle load: each 12,000 kg with air suspension and raise/lower valve * 235/75 R 17.5 3PMSF twin tires. Manufacturer at our discretion * Mechanical landing legs with 2-speed gearbox and crank. JOST Module B – static test load = approx. 50,000 kg * Throughout the loading platform and between the axles, interrupted approx. 50 mm thick hardwood decking (increases coefficient of friction) * 1 intermediate table, approx. 300 mm wide, for the telescopic tube with large cross-section. Intermediate table with offset loading platform and extendable mounting rails for aluminum bridging elements * Platform locking with conically welded locking profiles every approx. 250 mm. Includes pre-tensioning plate * 1 pair of lashing rings on the front cross member (LC 10,000 daN) * 9 pairs of recessed lashing rings in the outer frame of the loading area, foldable outwards (LC 10,000 daN) * 1 pair of fixed wheel recesses in front of the axles, open up to the gooseneck cross member, approx. 700 x 410 mm (W x D) * Wheel recesses with 15 x 15 mm square climbing strips and widenings at the bottom (in case vehicle is equipped with extendable widenings) * 1 pair of fixed wheel recesses, approx. 1,480 x 700 x 410 mm (L x W x D), in the platform between 1st and 2nd axle * Wheel recesses with 15 x 15 mm square climbing strips and widenings at the bottom * Aluminum covers for the wheel recesses in front of the axles and between the 1st and 2nd axle, which can also be used as widening planks (if vehicle is equipped with extendable widenings) * Lockable aluminum elements installed on the extension tubes of the widenings * 1 pair of mechanical rear supports * 1st axle with traction aid * Sandblasting painted...

Condition: excellent (used), axle configuration: 2 axles, permissible axle load (axle 1): 10,500 kg, permissible axle load (axle 2): 10,500 kg, first registration: 06/2017, total length: 7,000 mm, total width: 2,500 mm, total height: 880 mm, suspension: air, tire size: 235/70 R17.5, tire condition: 75 %, color: other, Equipment: ABS, = Additional options and accessories = - 2 axles - Air suspension = More information = General information Year of construction: 2017 Registration number: QALO590 Axle configuration Tyre size: 235/70 R17.5 Tyre profile: 75% Njdpsz S Ulbofx Aiaolh Brakes: drum brakes Suspension: air suspension Rear axle 1: Double wheels; Max. axle load: 10500 kg Rear axle 2: Double wheels; Max. axle load: 10500 kg Weights GVW: 21.000 kg Condition Technical condition: very good Visual appearance: very good

Condition: used, Year of construction: 2018, Faymonville Maxtrailer F-S43-1AAF. Year: 2018. 9-ton SAF axles. Weight: 9,961 kg. Max. weight: 45,000 kg. Kingpin load: 18,000 kg. Power steering on 3 steering axles. 7.5-meter extendable. Air suspension. Stainless steel toolboxes. Radio remote control. 1st axle is a lift axle. EBA ABS ALB. Floor dimensions: L: 13,550 mm. W: 2,480 mm. H: 1,400 mm. H: Aluminum boards: 600 mm. Tires: 385/65R22.5, 70% remaining tread. ID No.: 513. The General Terms and Conditions of Heinhuis apply to all advertisements, offers, and quotations by Heinhuis, as well as all agreements entered into by Heinhuis and the negotiations preceding them. By any form of response, you accept the applicability of the General Terms and Conditions of Heinhuis and declare that you have taken note of these General Terms and Conditions. Our prices are export net prices. = Further Information = Year of manufacture: 2018 Unladen weight: 9,961 kg Payload: 35,039 kg GVWR: 45,000 kg Extendable platform: Yes = Company Information = Nlsdezybzyepfx Aiajh For more information:

Condition: new, maximum load weight: 36,400 kg, overall weight: 48,000 kg, axle configuration: 3 axles, total width: 2,540 mm, Equipment: ABS, You will find our complete vehicle inventory, including immediately and soon-to-be available vehicles, on our website. Excerpt from the equipment. Full equipment details available upon request. - Gooseneck in SNT design to optimize load platform length, approx. 3,700 mm long, with a rear taper approx. 1,000 mm x 6° Nedpfeyhkquex Aiaolh - For tractors: 4 x 2 and 6 x 2 - ASPÖCK-UNIBOX at the front connection panel with 24N, 24S & 15-pin sockets - 3 kW electro-hydraulic power pack for hydraulic operations (excluding hydraulic winches). Without supply line installation on the tractor unit - Outer beams of the gooseneck with mounting holes for boltable lashing rings. First hole approx. 200 mm from the front, subsequent holes approx. every 400 mm. 2 pairs of screw-in lashing rings included (LC 5,000 daN) - One mounting hole at the rear upper part of the gooseneck’s outer beams for a boltable lashing ring - 1 pair of screw-in lashing rings included (LC 10,000 daN) - 3 pairs of recessed lashing rings inside the gooseneck’s outer beams (LC 5,000 daN) - 3 pairs of recessed lashing rings in the center of the gooseneck (LC 5,000 daN) - 1 pair of recessed lashing rings at the rear center of the gooseneck (LC 5,000 daN) - Grating covering on the gooseneck and rear taper with 5 mm steel reinforcement - 2" kingpin - Round NATO socket at the front connection panel (Maeler & Kaege VG 96 917) - Spiral cable for powering the electro-hydraulic unit and/or electric winch (approx. 35 mm², approx. 3.5 m long) between trailer and tractor unit, with plug (NATO-NATO) - 1 pair of detachable aluminum side boards on the gooseneck, approx. 400 mm high, anodized finish CARGO AREA: - Cargo area, approx. 9,600 mm long, with rear taper approx. 900 mm x 6° - Cargo area behind the gooseneck hydraulically liftable and lowerable, approx. 3,000 mm long, load capacity up to approx. 9,000 kg - TPMS (Tire Pressure Monitoring System) according to ECE R 141 - BPW axles and suspension, 1st and 2nd axles fixed, 3rd axle with trailing steering. 3rd axle with electromagnetic reverse lock via reverse gear and manual activation - Technical axle load: 12,000 kg each - Air suspension with lift and lower valve - 235/75 R 17.5 3PMSF twin tires. Brand of our choice, load index 143/141J (144/144F) - Mechanical landing legs with 2-speed gearbox and crank - Continuous grating flooring with approx. 5 mm steel plating for additional reinforcement, designed for point loads: on the lift bed and cargo area - Painted sand coating on the gooseneck cover plates as well as transition areas between neck and lift bed, lift bed and cargo area, and cargo area and ramps - 1 spare wheel mounting bracket under the cargo area to the right in front of the axles - Cut-outs in the outer frame of the cargo area and lift bed for attaching tie-down straps (LC 2,000 daN) - 11 pairs of recessed, fold-out lashing rings in the outer frame of the cargo area (LC 10,000 daN): 3 pairs in the lift bed outer frame, 8 pairs in the cargo area outer frame - 11 pairs of recessed lashing rings along the central beam (LC 5,000 daN): 3 pairs in the lift bed, 8 pairs in the rear cargo area - Control valves for the hydraulic ramps located on the right side of the vehicle - 1 pair of foldable mechanical rear supports, single-hand operation HYDRAULIC LOADING RAMPS: - 1 pair of two-part AXS steel ramps, approx. 4,920 mm long, and a

Condition: new, maximum load weight: 38,370 kg, overall weight: 49,500 kg, axle configuration: 3 axles, loading space length: 960 mm, loading space width: 254 mm, Year of construction: 2026, Manufacturer: Faymonville Type: Multimax Plus Year of construction: 2026 Product type: New Data: Gooseneck, length x width: 3.70 x 2.48 m Loading platform, length x width: 9.60 x 2.54 m Number of axles: 3 Nlodpfx Aszdmi Reiajh Payload: 38,370 kg Unladen weight: +/- 11,130 kg Permissible total weight: 49,500 kg Equipment: BPW axles and suspension, 1st and 2nd axles rigid, 3rd axle with trailing steering. 3rd axle with electro-magnetic reversing lock, activated via reverse gear and manually. Technical axle load: 12,000 kg. Painted sandblasted finish on the cover plates of the gooseneck and in the transition areas between the gooseneck and the lift platform, between the lift platform and the loading platform, and between the loading platform and the ramps. 1 spare wheel with mounting adapter under the loading platform on the right side in front of the axles. Cutouts in the outer frame of the loading platform and the lift platform for attaching lashing straps (LC 2,000 daN). Special equipment: Electric winch, approx. 5,400 kg pulling force, with radio remote control. Wire rope approx. 24 m long, rope diameter approx. 9.5 mm, including rope clamping roller. Mounting of the winch at the front inside of the gooseneck. 1 INOX protective box for the electric winch 5,400 kg, approx. 825 x 340 x 390 mm (L x W x H) in a straight design, with 1 lid on top and a cutout for the winch cable. 1 INOX tool box, approx. 620 x 300/180 x 950 mm (L x H x D), mounted on the left and right under the loading platform in front of the axles and sloped towards the rear. WABCO Smart Board system. Axle load information is valid when the vehicle is at its nominal driving height; otherwise, deviations are possible. The Smart Board is equipped with an odometer. 1st axle with starting aid. Relief of the air springs up to 30 km/h and up to 130% of the legal axle load on the remaining axles. Operation via the brake pedal in the central control unit. Storage for the bridging parts of the ramps in front of the axles. Information: Sample images Note: Location: Essen, immediately available.

Condition: used, empty load weight: 13,870 kg, maximum load weight: 55,930 kg, overall weight: 69,800 kg, axle configuration: > 3 axles, loading space length: 88,000 mm, loading space width: 2,540 mm, suspension: air, tire size: 235/75 R 17.5, Year of construction: 2026, Equipment: ABS, Gooseneck: -Gooseneck in SNT design for optimizing the loading area length, length approx. 3,700 mm -Gooseneck with a bevel at the rear approx. 1,000 mm x 10° -Technical fifth wheel load: 25,000 kg Nedpfszx Aa Ujx Aiajlh -For semi-trailer tractors: 4 x 2, 6 x 2 and 6 x 4 Loading platform: -Loading platform in extendable design, length approx. 8,800 mm, with bevel at the rear approx. 500 mm x 10° -Excavator arm approx. 2,490 x 750 x 210/290 mm Ramps: -A pair of two-part steel ramps, approx. 4,350 mm x 900 mm, hardwood surface -Ramps can be individually shifted outwards by approx. 235 mm and inwards by approx. 215 mm, hydraulically -Hardwood surface on the bevel of the loading platform -Square climbing strips 20 x 30 mm, approx. every 200 mm on the outer frame of the ramp Axles, suspension and tires: -BPW axles and suspension, 1st and 2nd axles rigid, 3rd and 4th axles trailing -Technical axle load: 12,000 kg -Air suspension with lifting and lowering valve -Tires: 235/75 R17.5 -TPMS tire pressure monitoring sensors mounted in all wheels, including spare wheel Included accessories: -Steel front wall, pluggable, height approx. 400 mm -Round NATO socket on the connection strip at the front -3 kW electric-hydraulic unit -1 spare wheel -The first hole approx. 200 mm from the front, then approx. every 400 mm -2 pairs of screw-in lashing rings included -1 pair of screw-in lashing rings -On the gooseneck, 1 pair of pluggable aluminum sideboards, approx. 400 mm high, anodized -On the gooseneck, a pluggable aluminum rear panel, approx. 400 mm high, anodized -2" kingpin -Guide plate from the gooseneck for the fifth wheel plate, approx. 500 mm wide -4 shims -Mechanical fifth wheel landing gear with 2-speed gearbox and crank JOST Module B – static test load = 50,000 kg -On the loading platform, continuous hardwood surface approx. 50 mm thick, interrupted between the axles -Locking of the loading platform with conical welded locking profiles every 250 mm including a tensioning plate -Slotted holes for attachable and adjustable bridge elements at the front of the loading platform -1 intermediate table with recessed loading platform, approx. 300 mm wide for the extension tube with a large cross-section with a sheet metal surface -At the front and rear with slotted holes for attachable and adjustable bridge elements -Removable cover at the same height as the loading platform -1 pair of lashing rings on the front crossmember -6 pairs of recessed lashing rings in the outer frame of the loading platform, foldable outwards -In addition, 1 pair of lashing rings on the outside of the front crossmember of the loading platform, rotated inwards by approx. 90° to the loading platform -Extensions (galvanized) extendable by approx. 230 mm each side -1 pair of permanently installed wheel wells open to the extension, approx. 700 x 410 mm, in the loading platform in front of the 1st axle -Wheel well with sheet metal surface and square climbing strips 15x15mm, approx. every 200 mm -Between the 2nd and 3rd axles in the loading platform, a pair of permanently installed wheel wells, approx. 1,695 x 700 x 410 mm -Cover for wheel wells -1 pair of mechanical rear supports -Central lubrication system with 1 pump -Galvanized stands for the extendable extensions in the wheel wells, to widen the wheel well covers -Square climbing strips 20 x 30 mm, approx. every 200 mm on the outer frame of the bevel of the loading platform -WABCO Smartboard System -1st axle with automatic lift axle function as well

Condition: new, maximum load weight: 73,540 kg, overall weight: 102,000 kg, axle configuration: > 3 axles, Equipment: ABS, You can find our complete vehicle inventory, including vehicles available for immediate and short-term delivery, on our website. Excerpt from the equipment list. Complete equipment list available upon request. Gooseneck: * Hydraulically extendable/retractable and lowerable gooseneck, length ± 3,650 mm * 2 pairs of lashing rings, foldable outwards (LC 5,000 daN) * 2 pairs of lashing rings on the gooseneck (LC 10,600 daN) * 1 pair of lashing rings in the middle section of the gooseneck (LC 10,600 daN) * Suitable for 6 x 4 or 8 x 4 tandem axle vehicles Compact front axle: * Hook receiver at the front and rear, length: approx. 2,200 mm * Axle width: approx. 2,850 mm Excavator bridge: * Telescopic excavator bridge with traversable bridge hooks at the front and pin-and-plate coupling at the rear * Overall width: approx. 2,850 mm * Length: approx. 6,650 mm * Beam height: approx. 400 mm * Beam width: approx. 1,350 mm * Loading height approx. 550 mm with ground clearance approx. 150 mm 4-axle rear axle: * Mechanical pin-and-plate coupling for mounting a low-bed trailer at the front * End crossbeam at the rear, axle width: approx. 2,850 mm * Axle length: approx. 5,480 mm Swivel axles, all axles hydro-mechanically force-locked * Technical axle load: 14,640 kg each (62 km/h) * Hydraulic axle suspension Tires: * Front axle: * 8 x tires, selection according to manufacturer (M+S) 285/70 R19.5 * Rear axle tires: * 16 x tires, selection according to manufacturer (M+S) 285/70 R19.5 * Load index 150/148J Painting: * Complete steel construction automatically blasted with a shot blasting system after welding. Second blasting with corundum for optimal adhesion of the coating system. * HRM metallization of the entire vehicle chassis with ZINACOR 850 (85% zinc/15% aluminum) to ensure the best corrosion protection. * Final painting with 2 layers of 2K topcoat, single-color in RAL 3002 carmine red, according to the RAL 841GL system. Nledpfjxbmplox Aiaoh Including the following accessories: * Steel front panel, approx. 400 mm high * Aluminum side and rear walls, pluggable on the gooseneck, approx. 400 mm high, in anodized finish * 3.5-inch kingpin * Truck hydraulic connection with flow control (20 l/min) * Gantry for suspending the supply lines; the SZM tank must have a minimum capacity of 80 liters. * With MAX Trailer coupling parts; otherwise, coupling parts must be supplied by the customer. * BEKA-MAX central lubrication for one gooseneck with standard grease NLGI-2 * Tool kit, type No. 612452 * Multi-coupling hydraulic connections on the gooseneck * Front axle with a separate air connection for air suspension * BEKA-MAX central lubrication for a 2-axle axle with standard grease NLGI-2 * One 7-pole socket on the left and right at the rear of the front axle for warning signs * Screw-in option (approx. 40 mm diameter) every approx. 500 mm on the outside of the top chord of the outer beam of the excavator bridge for screw rings (LC 16,000 daN) * Foldable wideners with steel mats, adjustable in width from approx. 2,850 mm to approx. 3,250 mm * BEKA-MAX central lubrication for a 4-axle axle with standard grease NLGI-2 * On the rear axle, a socket for the cable remote control of the trailing axle * Rear axle with tipper body * Two INOX toolboxes, approx. 855 x 340 x 390 mm, on the gooseneck, left and right * 1-cylinder Hatz diesel engine (Silent Pack) with electric starter and starter battery * Radio remote control: * Operation of the power pack, start/stop of the diesel engine

Condition: used, color: red, Year of construction: 2011, Faymonville STBZ-4VA. Year: 2011. 10-ton SAF axles. Weight: 22,500 kg. Load capacity: 57,500 kg. Max. weight: 80,000 kg. Kingpin load: 40,000 kg. EBS ABS ALB. Hydraulic system, powered from the trailer, operates on NATO electricity. Hydr. detachable gooseneck. 5 meters extendable. 2 x spare tire. Zinc-coated! Air suspension. Excavator bridge: 5600 x 950 mm. Remote control on cable. Dimensions: Neck: L: 4500 mm. W: 2550 mm. H: 1750 mm. Kingpin height: 1250 mm. Floor: L: 7550 mm. W: 2750 mm. H: 530 mm. Floor thickness: 350 mm. Rear trailer: L: 5600 mm. W: 2750 mm. H: 1000 mm. Tires: 235/75R17.5 70%. Dolly D-2. Year: 2012. 10-ton SAF axles. Weight: 4300 kg. Max. weight: 38,000 kg. Kingpin load: 18,000 kg. Air suspension. Tires: 235/75R17.5 70%. German trailer! ID No.: 624. Nedpfezya Ewex Aiaelh The General Terms and Conditions of Heinhuis apply to all advertisements, offers, and quotations by Heinhuis, all agreements entered into by Heinhuis, and the negotiations preceding them. By any form of response, you accept the applicability of the General Terms and Conditions of Heinhuis and declare that you have taken note of these General Terms and Conditions. Our prices are export net prices. = Further Information = Year of manufacture: 2011 Unladen weight: 22,500 kg Payload: 57,500 kg GVW: 80,000 kg Extendable structure: Yes = Company Information = For more information:

Condition: good (used), axle configuration: 2 axles, first registration: 03/2004, total length: 15,600 mm, total width: 2,550 mm, color: green, Equipment: ABS, - Air suspension - Central lubrication system Rear axle 1: Steered Rear axle 2: Steered Unladen weight: 13,400 kg Payload: 22,600 kg GVWR: 36,000 kg Superstructure brand: FAYMONVILLE STBZ-2VA Loading platform height: 45 cm Technical condition: good Optical condition: good FAYMONVILLE STBZ-2VA – 2-AXLE LOW LOADER – TELESCOPIC – DETACHABLE GOOSENECK – HYDRAULICALLY STEERED Well-maintained and robustly built Faymonville STBZ-2VA 2-axle low loader, equipped with a detachable gooseneck, telescopic platform, hydraulically steered axles, air suspension, and a central lubrication system. A professional low loader for the transport of construction machinery, excavators, wheel loaders, cranes, as well as long and heavy machinery. GENERAL DATA * Manufacturer: Faymonville * Type: STBZ-2VA * Design: 2-axle low loader * First registration: 19.03.2004 * Number of axles: 2 * Axle manufacturer: BPW * Both axles hydraulically steered * Air-suspended * Central lubrication system * Detachable gooseneck * Excavator boom recess at the rear * Tires: 235/75 R17.5 LOW PLATFORM / LOADING AREA The Faymonville features a particularly low and widely telescopic platform. * Platform length retracted: approx. 840 cm * Telescopic extension: approx. 550 cm * Max. platform length extended: approx. 1,390 cm * Width: approx. 255 cm * Loading height: only approx. 45 cm * Thickness of the loading platform: approx. 24 cm Due to the very low loading height of only approx. 45 cm, this low loader is ideally suited for the transport of tall machinery where the lowest possible overall height is crucial. The platform is telescopically extendable by an impressive 5.50 meters. This also makes the semi-trailer excellent for particularly long machines, structures and special transports. DETACHABLE GOOSENECK Equipped with a detachable gooseneck. This allows self-propelled machines to be conveniently driven directly onto the low platform from the front. Ideally suited for the transport of: * Excavators * Crawler excavators * Bulldozers * Wheel loaders * Crawler cranes * Road construction machinery * Agricultural machinery * Heavy and special construction machinery AXLES & CHASSIS Equipped with 2 BPW axles, both of which are hydraulically steered. The hydraulic steering ensures excellent maneuverability and is a major advantage, especially in tight construction sites, industrial plants and special transports. In addition, the low loader has air suspension, which ensures good driving characteristics and optimal load distribution. WEIGHTS * Technical total weight: approx. 36,000 kg Nlsdpfx Aijzy I Tveash * Unladen weight: approx. 15,600 kg * Specified payload: approx. 22,600 kg Note: The specified weights should be checked against the vehicle documents, as the unladen weight and specified payload together amount to 38,200 kg. DIMENSIONS * Overall length of low loader: approx. 1,560 cm * Width: approx. 255 cm * Platform length retracted: approx. 840 cm * Telescopic extension: approx. 550 cm * Max. platform length extended: ...

Condition: used, color: red, Year of construction: 2012, Faymonville STBZ-4VA. Year: 2012. 10-ton SAF axles. Weight: 22,500 kg. Nljdpfxezya Eqj Aiajh Load capacity: 57,500 kg. Max. weight: 80,000 kg. Kingpin load: 40,000 kg. EBS ABS ALB. Hydraulic system powered by trailer, operates on NATO electricity. Hydr. detachable gooseneck. 5-meter extendable. 2 spare tires. Zinc-coated! Air suspension. Excavator bridge: 5600 x 950 mm. Remote control with cable. Dimensions: Neck: L: 4500 mm. W: 2550 mm. H: 1750 mm. Kingpin height: 1250 mm. Floor: L: 7550 mm. W: 2750 mm. H: 530 mm. Floor thickness: 350 mm. Rear section of trailer: L: 5600 mm. W: 2750 mm. H: 1000 mm. Tires: 235/75R17.5, 80%. Dolly D-2. Year: 2012. 10-ton SAF axles. Weight: 4300 kg. Max. weight: 38,000 kg. Kingpin load: 18,000 kg. Air suspension. Tires: 235/75R17.5, 70%. German trailer! ID No.: 629. The General Terms and Conditions of Heinhuis apply to all advertisements, offers, and quotations by Heinhuis, all agreements entered into by Heinhuis, and the negotiations preceding them. By any form of response, you accept the applicability of the General Terms and Conditions of Heinhuis and declare that you have taken note of these General Terms and Conditions. Our prices are export net prices. = Further information = Year of manufacture: 2012 Unladen weight: 22,500 kg Payload: 57,500 kg GVW: 80,000 kg Extendable superstructure: Yes = Company information = For more information:

Condition: new, axle configuration: 3 axles, permissible axle load (axle 1): 10,000 kg, permissible axle load (axle 2): 10,000 kg, permissible axle load (axle 3): 10,000 kg, loading space length: 29,000 mm, loading space width: 2,540 mm, loading space height: 2,850 mm, total length: 29,000 mm, total width: 2,540 mm, total height: 2,850 mm, suspension: air, tire size: 385/65-R22.5, Equipment: ABS, - BPW axles - EBS - Air suspension - Disc brakes - Central lubrication system NEW MAX210-Z-3AA-13.60-22.5-2.54, available directly from stock Technical data MAX210-Z-3AA-13.60-22.5-2.54 Total weight: 48,000 kg / Coupling pressure: 18,000 kg / Axle load: 30,000 kg / Tare weight: 11,456 kg / Payload approx.: 36,544 kg / Coupling height (laden): 1150–1250 mm / Turning radius: 2300 mm Loading area length: 13,600 mm / 2-way extendable (2 x 770 mm) to 2900 mm / Wheelbase: 1810 mm Technical description: Extendable loading area with pneumatic locking / A fixed intermediate table of ± 250 mm is located in the central box structure. / 8 pairs of lashing eyes that fold outwards (LC 5,000 daN) / 3 pairs of lashing eyes that fold outwards (LC 10,000 daN) / Recesses in the outer frame for attaching lashing straps (LC 2,000 daN) Tires: Tires 385/65 R22.5 (Brand: Goodyear) Tire pressure monitoring system (TPMS): TPMS according to ECE R 141 Axles: BPW axles with disc brakes, air-suspended with raising and lowering valve. All axles are hydromechanically steered. Technical axle load: 10,000 kg (ET 0) Braking system: WABCO braking system according to EU regulations with EBS-E system (2S2M), without connecting cable to the tractor. Steel structure: Steel structure made of high-quality fine-grain steel. Steel grades: S355J2+N/S355MC (Yield strength 355 MPa) / S690QL/S700MC (Yield strength 690 MPa) Electrical system: Electrical system according to EU regulations, lighting 24 V ASPÖCK-NORDIK (ASS3). ASPÖCK-UNIBOX on the galvanized connection strip at the front with 24N, 24S and 15-pin sockets. Connections according to ISO / 24N ISO-1185 / 24S ISO-3731 / 15-pin ISO-12098 Warning signs: Below the gooseneck and at the rear, left and right, holder for warning signs with socket. Options: • Maneuverability at the front and rear via cable remote control with PDC light control for axle alignment. (without mounting on the tractor) • Electro-hydraulic unit (approx. 45 kg) • 2 wheel chocks with holder on the partition wall • Kingpin 2" • Galvanized steel partition, approx. 1600 mm high. EN12642-XL • White reflector tape according to EU regulations over the entire length and width. Red at the rear. • EU marking plates (red-yellow) at the rear of the vehicle. • Holder for a rotating beacon at the rear of the vehicle. • Loading floor made of 30 mm thick hardwood, reinforced with omega profiles (approx. 298 kg). • 10 pairs of stake holder, approx. 100 x 50 mm, in the outer frame of the loading floor. • 1 spare wheel holder under the loading floor on the right. • BEKAMAX (Pico) central lubrication system with 2 pumps. • 6 pairs of recesses in the loading floor for WADER container locks, for 1 x 20', 2 x 20', 1 x 40' or 1 x 45' container. • 5 pairs of stake profiles, mounted across in the loading floor, for stakes 100 x 50 mm Nljdpfxs Aba Iro Aiaoh • Galvanized storage compartment under the loading floor (2390 x 720 x 400 mm) • Rope hooks (8 mm), every approx. 500 mm below the edge profile of the gooseneck and the loading floor • Ladder, mounted on the left in the direction of travel • Stainless steel toolbox • LED lighting • 10 pairs of twist locks (100 x 50 mm, length 1000 mm) • 8 container General information Year of manufacture: 2026...

Condition: used, color: red, Year of construction: 2012, Faymonville STBZ-4VA. Year: 2012. 10-ton SAF axles. Weight: 22,500 kg. Load capacity: 57,500 kg. Max. weight: 80,000 kg. Kingpin load: 40,000 kg. EBS ABS ALB. Hydraulic system, powered by the tractor unit via NATO socket. Hydraulic detachable gooseneck. 5-meter extendable. 2 spare tires. Zinc coated! Air suspension. Excavator bridge: 5600 x 950 mm. Remote control on cable. Dimensions: Neck: L: 4500 mm. W: 2550 mm. H: 1750 mm. Kingpin height: 1250 mm. Floor: L: 7550 mm. W: 2750 mm. H: 530 mm. Floor thickness: 350 mm. Rear trailer section: L: 5600 mm. W: 2750 mm. H: 1000 mm. Tires: 235/75R17.5, 80%. Dolly D-2. Year: 2012. 10-ton SAF axles. Weight: 4300 kg. Max. weight: 38,000 kg. Kingpin load: 18,000 kg. Air suspension. Tires: 235/75R17.5, 70%. German trailer! ID No.: 589. The General Terms and Conditions of Heinhuis apply to all advertisements, offers, and quotations by Heinhuis, all agreements entered into by Heinhuis, and the negotiations preceding them. By any form of response, you accept the applicability of the General Terms and Conditions of Heinhuis and declare that you have taken note of these General Terms and Conditions. Our prices are export net prices. Njdpfx Aiezya Nvoaelh = Further Information = Year of manufacture: 2012 Unladen weight: 22,500 kg Payload: 57,500 kg GVW: 80,000 kg Extendable platform: Yes = Company Information = For more information:

Condition: used, maximum load weight: 25,630 kg, overall weight: 38,000 kg, axle configuration: 2 axles, first registration: 11/2024, next inspection (TÜV): 11/2026, Equipment: ABS,

Condition: excellent (used), first registration: 09/2015, loading space length: 20,180 mm, loading space width: 3,000 mm, color: other, Damages: none YAFTL2007F0017329 = More information = Year of construction: 2015 Empty weight: 13.600 kg Carrying capacity: 28.400 kg GVW: 42.000 kg Technical condition: very good Visual appearance: very good Price: On request Registration number: DW205AH = Dealer information = Do you have any questions or suggestions? Please feel free to contact us. We guarantee a response within 8 hours. Prices do not include VAT. No rights may be derived from the information provided. Office phone number: Mobile: Dutch - English - German - French - Spanish - Italian) Available via WhatsApp and Viber. Nodpfsymrb Sox Aiaolh Mobile: Available via WhatsApp and Viber. When paying by bank transfer, the funds must be transferred to our bank account listed below. Always verify the payment details on our website. Please contact us if you have received different information. If in doubt, please call us so we can verify the invoice and/or payment. Bank details: Bank name: ING Bank address: Bijlmerdreef 106 1102 CT Amsterdam IBAN number: NL97INGB0117176699 EORI/VAT/TAX: NL810574901B(01) BIC/SWIFT: INGBNL2A

Condition: good (used), axle configuration: 3 axles, permissible axle load (axle 1): 12,000 kg, permissible axle load (axle 2): 12,000 kg, permissible axle load (axle 3): 12,000 kg, first registration: 08/2012, total length: 17,700 mm, total width: 3,000 mm, total height: 3,400 mm, suspension: hydraulics, tire size: 285/70 19.5, wheelbase: 1,300 mm, Year of construction: 2012, Equipment: ABS, = Additional Options and Accessories = - Flashing lights - EBS (Electronic Braking System) - Air suspension, rear - Spare wheel = Notes = - Faymonville 3-axle Euro flatbed trailer (model: STBZ-3V) * Lower deck: - Dimensions: length 835 cm x width 300 cm - Loading floor height: 66 cm - Lashing eyes * Upper deck: - Dimensions: length 334 cm x width 242 cm x height 40 cm - Loading deck height: 200 cm - Aluminum side panels all around - Lashing eyes * Rear deck - Dimensions: length 452 cm x width 273 cm - Loading deck height: 111 cm - Lashing eyes - Both sides can be widened by 22 cm - Multifaster - Includes remote control for manual adjustment on site - Boom slot - Pendulum axles - All axles are hydraulically suspended and steered! Nledpfx Aiozp Ruzjajh - 12-metric-ton axles! / 14.4-metric-ton axles (technical rating)! - 30 metric tons kingpin load! / 37.5 metric tons kingpin load (technical)! * Also available for sale in combination with a MAN TGX 41.640 Euro 6 8x4 tractor (ID 46504) = Further Information = Axle configuration Tire size: 285/70 19.5 Suspension: hydraulic suspension Rear axle 1: Dual tires; Max. axle load: 12000 kg; Steered; Tire tread depth left inner: 60%; Tire tread depth left outer: 60%; Tire tread depth right inner: 60%; Tire tread depth right outer: 60% Rear axle 2: Dual tires; Max. axle load: 12000 kg; Steered; Tire tread depth left inner: 70%; Tire tread depth left outer: 70%; Tire tread depth right inner: 70%; Tire tread depth right outer: 70% Rear axle 3: Dual tires; Max. axle load: 12000 kg; Steered; Tire tread depth left inner: 70%; Tire tread depth left outer: 70%; Tire tread depth right inner: 70%; Tire tread depth right outer: 70% Weights Unladen weight: 17,950 kg Payload: 48,050 kg GVWR (Gross Vehicle Weight): 66,000 kg Condition Technical condition: good Optical condition: good Product Safety Manufacturer: Clean Mat Trucks B.V. Wageningsestraat 17 6673DB ANDELST, NL

Condition: used, maximum load weight: 25,600 kg, overall weight: 38,000 kg, axle configuration: 2 axles, first registration: 07/2025, next inspection (TÜV): 07/2027, Equipment: ABS, Excerpt from the equipment list. Complete equipment available upon request. Gooseneck Gooseneck Light, length approx. 4,080 mm Hydraulically extendable and retractable gooseneck For semi-trailer combinations: 4 x 2 and 6 x 2 Drop Deck Drop deck designed as a telescoping excavator bridge with a front extension and a mechanical locking mechanism. Length x width approx. 6,350 mm x 1,300 mm Rear Axle Assembly Rear axle assembly in a short design with a closed outer frame and diamond plate covering with an excavator well, which is closed in the rear half to accommodate the air tanks. Axles and Suspension BPW axles and suspension, all axles hydro-mechanically steered Technical axle load: 12,000 kg Air suspension with lifting and lowering valve Axle tool Tires 235/75 R 17.5 3PMSF dual tires Load index 143/141J (144/144F) Braking System WABCO EBS-E braking system in accordance with EU regulations Without connection cable to the tractor unit Painting Nodpfozlmkwjx Aiaolh 6-layer end treatment Complete steel construction blasted after welding 1 coat of zinc-based primer, 1 coat of adhesion primer Final coating with 2 coats of 2-component paint (acrylic), single color in RAL 3002 carmine red, followed by sealing of cavities with special wax. Rims in silver. Included Accessories Steel headboard, plug-in type, approx. 400 mm high Connection strip for supply lines to the semi-trailer combination, mounted at the height of the outer frame profile Round NATO socket on the connection strip at the front (Maeler & Kaege VG 96 917) 3 kW electro-hydraulic unit for controlling hydraulic operations, with the exception of hydraulic winches 3 pairs of recessed lashing rings on the gooseneck (LC 5,000 daN) 2 pairs of welded lashing rings LBS 3 (LC 6,000 daN), at the front approx. 600 mm behind the headboard and at the rear on the gooseneck 2 pairs of welded lashing rings LBS 3 (LC 6,000 daN), on the outer frame of the gooseneck On the gooseneck, 2 pairs of plug-in aluminum side boards, approx. 400 mm high, in anodized design On the gooseneck, a plug-in aluminum rear panel, approx. 400 mm high, in anodized design Above the gooseneck, approx. 12 mm thick Delignit flooring 2-inch kingpin Hydraulic cross member for supporting the gooseneck on the semi-trailer combination or a dolly Air connection with air gun on the gooseneck Access to the gooseneck 2 pairs of rung pockets recessed on the gooseneck, for plug-in rungs approx. 100 x 100 mm On the outer tube, threaded holes for mounting screw-on lashing rings M24 (LC 8,000 daN) 2 pairs of screw-on lashing rings M24 (LC 8,000 daN) included On the top flange, approx. every 1,200 mm, attachment point ø26 mm for screw-on rings (LC 8,000 daN) 10 pairs of lashing rings on the outer girder RBS-5 (LC 10,000 daN), under and between the widening sections Folding, extendable widening sections, lockable to approx. 2,550/2,750/3,000 mm, incl. steel mattresses in a split design, with wooden flooring Bevel at the front of the axle assembly, approx. 350 mm x 12°, including integrated attachment rails at the front and rear for loose loading ramps 2 pairs of lashing rings with retaining spring at the transition from the drop deck to the excavator well (LC 10,000 daN) 3 pairs of recessed lashing rings in the outer frame of the axle assembly, foldable outwards: 1 pair at the front and 1 pair at the rear (LC 5,000 daN), 1 pair in the middle (LC 10,000 daN) 2 pairs of lashing rings LBS-3 (LC 6,000 daN) welded above the wheel arch on the rear axle

Condition: good (used), axle configuration: > 3 axles, permissible axle load (axle 1): 8,000 kg, permissible axle load (axle 2): 8,000 kg, permissible axle load (axle 3): 8,000 kg, first registration: 11/2017, total length: 135,000 mm, total width: 2,540 mm, total height: 780 mm, color: black, Equipment: ABS, = Additional options and accessories = - Air suspension = Further information = General information Year of manufacture: 2017 Axle configuration Rear axle 1: Max. axle load: 8000 kg Rear axle 2: Max. axle load: 8000 kg; Steerable Rear axle 3: Max. axle load: 8000 kg; Steerable Rear axle 4: Max. axle load: 8000 kg; Steerable Weights Unladen weight: 14,800 kg Payload: 42,200 kg GVW: 57,000 kg Condition Technical condition: good Visual condition: good Damage: none Nljdoyx Hwyopfx Aiaeh Financial information Price: On request Further information Please contact David F. Middelman for more information.

Condition: used, maximum load weight: 33,300 kg, overall weight: 42,000 kg, axle configuration: 3 axles, first registration: 09/2003, next inspection (TÜV): 01/2027, loading space length: 13,500 mm, loading space width: 2,500 mm, loading space height: 1,500 mm, total length: 13,600 mm, total width: 2,550 mm, total height: 3,200 mm, Equipment: ABS, Extendable semi-trailer, overall length adjustable from 7700 mm to 21300 mm, 9 stake pockets per side, 9 lashing points per side, all-round warning light / rear and center, extendable warning signs, JOST support jacks, central lubrication system, continuous underfloor box, ABS, EBS, SAF axle(s), last axle steered, drum brake system, air suspension with lifting and lowering mechanism, vehicle can be covered with advertising and/or lettering. SI86996 Our offer generally does not include a new TÜV inspection. If a new TÜV inspection is desired, we will be happy to provide you with a quote from our partner workshops! The vehicle can be covered with advertising and/or lettering. Our general terms and conditions of delivery and payment apply. We would be happy to prepare a financing or leasing offer for this item. Nljdpfozw Sgbex Aiash Please contact us!

Condition: used, machine/vehicle number: YAFTL408100008968, axle configuration: > 3 axles, first registration: 01/2008, total length: 13,400 mm, total width: 2,750 mm, total height: 3,400 mm, suspension: air, tire size: 245/70 R17.5, color: other, Year of construction: 2008, = Additional options and accessories = - Drum brakes - Steering Axle = Remarks = Chassis Diameter coupling pin / coupling plate: 2 inch Height of coupling pin / drawbar: 120 cm Drum brake: ✓ Nljdoxhgiropfx Aiajh Structure Construction year: 2008 Faymonville extendable 4-axle semi-lowbed trailer type STN 4AU, Gross weight 65000 kg, Load bed lenght 910 cm, Max load bed lenght when extended..... cm, Max load bed width 3 cm (275 cm), Load bed height 90 cm, Hydraulic ramps, Ramp width 85 cm, Air suspension, 2 passive steering axles, Gigant axles, Drum brakes, ABS, Tire size 245/70R17.5, Double tires, Shipment dimensions 1340x275x340 cm = More information = Axle configuration Make axles: Gigant Brakes: drum brakes Suspension: air suspension Front axle: Tyre size: 245/70 R17.5; Tyre profile left: 60%; Tyre profile right: 35% Middle axle: Tyre size: 245/70 R22.5; Tyre profile left: %; Tyre profile right: 50% Rear axle 1: Tyre size: 245/70 R17.5; Steering; Tyre profile left: 45%; Tyre profile right: 20% Rear axle 2: Tyre size: 245/70 R17.5; Steering; Tyre profile left: 50%; Tyre profile right: 60% Weights Empty weight: 17.500 kg Carrying capacity: 47.500 kg GVW: 65.000 kg Functional Make of bodywork: Faymonville = Dealer information = For more information on this unit please call: or e-mail: . A full stock overview can be found at: . Please do not forget to subscribe to our newsletter for weekly updates on our stock.

Condition: used, empty load weight: 9,600 kg, maximum load weight: 30,400 kg, overall weight: 40,000 kg, axle configuration: > 3 axles, first registration: 12/2011, loading space length: 13,200 mm, loading space width: 2,500 mm, loading space height: 800 mm, suspension: air, tire size: 205/65R17.5, color: green, mileage: 1,001 km, gearing type: other, driver cabin: other, Equipment: ABS, Vehicle location: Bovenden, 4 axles, SAF axles, air suspension, lifting and lowering function, 3rd and 4th axles self-steering, ABS (anti-lock braking system), extendable, lashing eyes, drive-on ramps can be fitted, front support legs, rear support legs, lateral aluminium side guard, storage box. Nledpfsxxkqzjx Aiash Body: 4-axle low-bed semi-trailer with attachable drive-on ramps, SAF axles, 3rd and 4th axles self-steering, 13 pairs of lashing rings, 10 pairs of preparations for plug-in stanchions, 13,200 mm loading length fully retracted, 16,800 mm loading length fully extended, 800 mm loading height in the low-bed area, low-bed length approx. 9,500 mm retracted, next technical inspection (TÜV) due, aluminium ramps available at extra cost of €1,500. ACCESSORY DETAILS WITHOUT GUARANTEE, subject to change, prior sale and errors excepted. - .

Condition: used, color: green, Year of construction: 2015, Faymonville F-S44-1ACA. Year: 2015. 10-ton SAF axles. Weight: 22,250 kg. Load capacity: 57,750 kg. Maximum weight: 80,000 kg. Kingpin load: 40,000 kg. EBS ABS ALB. Hydraulic system operates via the truck's NATO socket. Allu boards on the gooseneck. Hydraulic detachable gooseneck. Air suspension. 5-meter extendable. Radio remote control. Excavator bridge: 5600 mm x 950 mm. Tires: 235/75R17.5, 80% remaining. Dimensions: Neck: Length: 4900 mm. Width: 2500 mm. Height: 1800 mm. Kingpin height: 1300 mm. Floor: Length: 8000 mm. Width: 2750 mm. Height: 500 mm. Floor thickness: 300 mm. Rear trailer: Length: 5600 mm. Width: 2750 mm. Height: 1050 mm. Dolly D-2. Year: 2015. 10-ton SAF axles. Weight: 3650 kg. Maximum weight: 36,100 kg. Kingpin load: 16,100 kg. Air suspension. Tires: 235/75R17.5, 70% remaining. German trailer! 4 units available! ID No.: 552. The General Terms and Conditions of Heinhuis apply to all advertisements, offers, and quotations by Heinhuis, all agreements entered into by Heinhuis, and the negotiations preceding them. By any form of response, you accept the applicability of the General Terms and Conditions of Heinhuis and declare that you have taken note of these General Terms and Conditions. Our prices are export net prices. = Further information = Year of manufacture: 2015 Unladen weight: 22,250 kg Payload: 57,750 kg Permissible total weight: 80,000 kg Extendable: Yes Nodpfjzybxxsx Aiaolh Price: On request = Company Information = For more information:

Condition: used, color: red, Year of construction: 2012, Faymonville STBZ-4VA. Year: 2012. 10-ton SAF axles. Weight: 22,500 kg. Load capacity: 57,500 kg. Max. weight: 80,000 kg. Kingpin load: 40,000 kg. EBS ABS ALB. Hydraulic system powered by trailer, operates on NATO electricity. Hydr. detachable gooseneck. 5-meter extendable. 2 spare tires. Zinc-coated! Air suspension. Excavator bridge: 5600 x 950 mm. Remote control with cable. Dimensions: Neck: L: 4500 mm. W: 2550 mm. H: 1750 mm. Kingpin height: 1250 mm. Floor: L: 7550 mm. W: 2750 mm. H: 530 mm. Floor thickness: 350 mm. Rear section: L: 5600 mm. W: 2750 mm. H: 1000 mm. Tires: 235/75R17.5, 70%. Dolly D-2. Year: 2012. 10-ton SAF axles. Nodpfx Aijzya I Eeaelh Weight: 4300 kg. Max. weight: 38,000 kg. Kingpin load: 18,000 kg. Air suspension. Tires: 235/75R17.5, 70%. German trailer! ID No: 588. The General Terms and Conditions of Heinhuis apply to all advertisements, offers, and quotations by Heinhuis, all agreements entered into by Heinhuis, and the negotiations preceding them. By any form of response, you accept the applicability of the General Terms and Conditions of Heinhuis and declare that you have taken note of these General Terms and Conditions. Our prices are export net prices. = Further information = Year of manufacture: 2012 Unladen weight: 22,500 kg Payload: 57,500 kg GVW: 80,000 kg Extendable superstructure: Yes = Company information = For more information:

Condition: new, empty load weight: 9,450 kg, maximum load weight: 35,550 kg, overall weight: 45,000 kg, axle configuration: 3 axles, loading space length: 9,500 mm, loading space width: 1,560 mm, total width: 2,550 mm, tire size: 385/65 R 22,5, color: grey, Equipment: ABS, Gooseneck: - Gooseneck designed as a loading deck, fitted with aluminum chequer plate Nljdpfxoygvc Ho Aiaoh - Front tapered approx. 45° - Hydraulic lifting arm, lift/lower range approx. -280/+250 mm - Two kingpin positions at 2,300 mm and 2,000 mm from DSR - Suitable for tractor units: 4x2, 6x2, or 6x4 Loading Bay: - Loading bay, length approx. 9,500 mm, with bottom-mounted angle profiles for pallet mounting (distance from kingpin to center of axle assembly approx. 8,000 mm) Axles, Suspension and Tyres: - BPW stub axles, with drum brakes and independent wheel suspension, hydraulic axle compensation with lift and lower function - Axle lowering lock in case of suspension airbag failure, designed for max. pallet height 150 mm - Tyres: 385/65 R 22.5 - TPMS tyre pressure sensors installed in all wheels including the spare - TPMS tyre pressure monitoring system compliant with ECE R 141 Surface Treatment: - Entire steel structure automatically shot-blasted after welding using a turbine blasting system - Second blasting with corundum to optimise coating adhesion - HRM metallisation of the complete vehicle chassis with ZINACOR 850 (85% zinc/15% aluminium) for maximum corrosion protection - Final coat with two layers of 2K topcoat, single colour in Novagrau (DB 7350) - Paint system tested in salt spray test to ISO 9227-NSS; cavity sealing with special wax Included Accessories: - Removable steel front wall, approx. 400 mm high - Tool box with lid, integrated in the rear section of the gooseneck, approx. 640 x 700 x 215 mm - Removable aluminium rear wall on the gooseneck, approx. 400 mm high, anodised - One pair of folding aluminium sideboards on the gooseneck, approx. 400 mm high, anodised - 2" kingpin - 3 pairs of recessed lashing rings on the gooseneck (LC 6,300 daN) - At the front connection rail, yellow-red air couplings; operation lighting for the gooseneck, suspension, and hydraulic load restraints with on/off switch - Mechanical drop tube supports for approx. 48,000 kg support load - Access ladder mounted front right with 2 detachable handrails - WABCO Roll Stability Support (RSS) - 9 pairs of lashing rings (LC 6,300 daN) mounted on the longitudinal beams - Grating platform, level with the guiding rails for load securing, fitted to the longitudinal beams - Hydraulic preparation, including control unit, for mounting 3 pairs of our hydraulic load restraints - First and last axle manually liftable on left and right - Storage box behind axle assembly, left and right, splash-proof - Tapered rear edge for easier pallet loading - Rear lashing eyes mounted on the tail crossmember for mechanical bracing - 7-pin socket on the tail crossmember - Electro-hydraulic power unit - 4 wheel chocks with holders - 2 axle load gauges mounted on the left side incl. axle load diagram - 3 pairs of hydraulic load restraints with swivel arms, moveably mounted to longitudinal beams - Rear door with cross bracing, hinged left and hydraulically locked right, can be secured horizontally at 90°, 105°, and 270° - Folding underride guard for transporting up to 4 empty standard pallets - 1 spare wheel - Number plate holder including lighting, rear left on the trailer - Round NATO socket on front connection rail (Maeler & Kaege VG 96 917) - Central lubrication system with 1 pump, brand BEKAMAX, standard grease version

Condition: used, maximum load weight: 34,400 kg, overall weight: 45,000 kg, axle configuration: 3 axles, first registration: 09/2006, loading space length: 9,530 mm, loading space width: 1,565 mm, loading space height: 1,650 mm, total width: 2,550 mm, total height: 2,800 mm, Equipment: ABS, Concrete inner loader, loading length: 9530 mm, loading width: 1,565 mm, angle profiles in the loading area for pallet accommodation, hydraulic load securing, 6 heavy-duty lashing rings per side, NATO jump-start socket, ABS, EBS, BPW Eco axle(s), drum brake system, front drop supports, vehicle may have advertising stickers and/or lettering. SI86628 Our offer generally does not include new TÜV inspection. If a new TÜV inspection is desired, we are happy to provide you with an offer from our partner workshops! Vehicle may be provided with advertising stickers and/or lettering. Our general terms of delivery and payment apply. Nlodpfeymu Iuox Aiash We are happy to create a financing or leasing package for this item. Please contact us!

Condition: used, maximum load weight: 30,660 kg, overall weight: 43,000 kg, axle configuration: 2 axles, first registration: 03/2024, next inspection (TÜV): 03/2025, Equipment: ABS, You can find our complete vehicle inventory, including vehicles available for immediate and short-term delivery, on our website. Excerpt from the equipment: Complete equipment available upon request. Loading Platform * Low-bed with central beam in extendable design * Length approx. 6,750 mm * 5 pairs of lashing rings that fold outwards (LC 5,000 daN) * 1 pair of lashing rings that fold outwards (LC 10,000 daN) * 1 pair of lashing rings lying horizontally at the rear of the loading platform (LC 10,000 daN) * The supply lines are protected in the central beam and adapt to the respective low-bed length. Gooseneck * Length approx. 3,900 mm * Gooseneck hydraulically adjustable up/down and extendable * Technical saddle load: 23,000 kg Rear Chassis * Short design with closed outer frame and diamond plate cover * Chassis with excavator well, which is closed in the rear half to accommodate the air tanks * 2 pairs of lashing rings that fold outwards (LC 5,000 daN) * 1 pair of lashing rings that fold outwards (LC 10,000 daN) Axles * BPW axles Nledpfx Aozvt Tyjiaeh * Hydro-mechanically forced steered * Technical axle load: 12,000 kg each * Air suspension with lifting and lowering valve * Axle tool Tires * 245/70 R 17.5 3PMSF – Manufacturer of our choice, load index (146/146F) Braking System * According to EU regulations with EBS-E (2S2M) without connection lines to the tractor unit Steel Construction * Made of high-strength fine-grained steels * Steel grades: S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa) Paintwork * High-quality 2-component (2K) * Topcoat in solid color RAL 3002 carmine red Incl. the following additional equipment: * 2-inch kingpin * One galvanized steel front wall, approx. 400 mm high * One spare wheel holder in front of the front wall * Yellow-red air couplings on the galvanized connection strip at the front * 4 wheel chocks with bracket. (± 5 kg) * Steering from the front and rear via cable remote control, operable via push buttons, with single-axle steering control (without installation in the tractor unit) * Electro-hydraulic unit (± 45 kg) * Yellow reflector tape according to EU regulations on the side, on the extension, and at the rear of the trailer * 1 wooden block, approx. 500x250x200 mm * Attachment rail for aluminum loading ramps at the rear of the vehicle * One bracket for a rotating beacon at the rear of the trailer * One mud flap at the rear of the trailer * European reflector plates (red-yellow) at the rear of the trailer * On the gooseneck and at the rear panel, one bracket each on the left and right for warning signs including socket * Manual and description on a USB stick * Speed stickers 80 km/h at the rear and on both sides * Load gauge for determining axle loads including load diagram * Incl. special accessories: On the gooseneck, aluminum side and rear walls, plug-in, approx. 2,440 x 400 mm (L x H) * The rear galvanized end crossbars are removable. (Length of the structure approx. 2,560 mm). (± 46 kg) * On the gooseneck, a separate air connection with an air gun. * 2 work lights with a switch on the trailer, mounted on the gooseneck platform on the left and right * 6 pairs of rung pockets for end crossbars approx. 100 x 50 mm in the outer frame of the loading platform * 2 pairs in the outer frame of the chassis (± 29 kg) * Extensions, galvanized, extendable by approx. 230 mm per side (± 262 kg) * Hydraulic connections from the gooseneck to the low-bed with multi-coupling instead of screw co