Used Faymonville Open Flatbed Semitrailers for sale (191)

Condition: new, maximum load weight: 36,020 kg, overall weight: 48,000 kg, axle configuration: 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our full vehicle inventory, including immediately and short-term available vehicles, on our website. Excerpts from the equipment. Complete equipment details available on request. Gooseneck: * Gooseneck with rear bevel approx. 750 mm x 10° * 3 pairs of lashing rings (LC 5,000 daN) * Hardwood flooring approx. 30 mm thick Loading area: * Loading area with rear bevel approx. 1,000 mm x 8° * 5 pairs of fold-out lashing rings to the outside (LC 5,000 daN) * 3 pairs of fold-out lashing rings to the outside (LC 10,000 daN) * 1 pair of horizontal lashing rings at the front of the loading area (LC 10,000 daN) * Hardwood flooring approx. 48 mm thick, checker plate above the axles Two-piece steel ramps: * One pair of galvanized two-piece steel ramps, approx. 3,185 + 1,420 x 1,250 mm, with grating covering C40/5 (point load approx. 2.8 t on a surface of approx. 20 x 20 cm) * Ramp with hydraulically foldable ramp sections and hydraulic lifting system * Maximum load per pair: 30,000 kg Landing legs: * JOST landing legs (mechanical) with 2-speed gearbox for approx. 24 t lifting capacity (approx. 50 t test load) Axles: * BPW axles and suspension, 2 rigid axles, 1 steering trailing axle * Technical axle load: 12,000 kg each * Electromagnetic reverse lock activated via reverse gear and manually * Air suspension with raise/lower valve Tyres: * Tyres 235/75 R 17.5 3PMSF – brand at our discretion TPMS: * TPMS tyre pressure monitoring system according to ECE R 141 Brake system: * WABCO brake system compliant with EU regulations, with EBS-E (2S2M), without connection lines to the tractor unit Dcedpfjy Auhuex Agrog Steel construction: * Steel construction made of high-strength fine-grain steels * Steel grades: S355J2+N/S355MC (yield strength 355 MPa), S690QL/S700MC (yield strength 690 MPa) Electrical system: * Electrical system according to EU regulations, LED lighting 24V ASPÖCK-NORDIK (ASS3) * All LED side marker lights flash with the indicator * ASPÖCK-UNIBOX on the front connection bar with 24N, 24S & 15-pin sockets according to ISO. 24N ISO-1185, 24S ISO-3731, 15-pin ISO-12098 Paintwork: * HRM metallisation of the entire vehicle chassis with ZINACOR 850 (85% zinc/15% aluminum) to guarantee optimum corrosion protection * Finishing coat: 2 layers 2K topcoat, solid colour RAL 3002 carmine red as per RAL system 841GL * Rear section metallised and painted RAL 9010 (pure white) * Rims in silver Included accessories: * One bracket for warning signs on the gooseneck and at the rear left and right, including socket * 1 spare wheel holder under the loading area, right in the direction of travel * 2" kingpin * One galvanized steel front wall * Yellow-red air couplings on the galvanized front connection bar * 4 wheel chocks with brackets on the bulkhead * 3 height wooden boards * Galvanized folding supports under the loading area bevel * Bracket for rotating beacon at rear of trailer * Height-adjustable tarpaulin structure – approx. 3,960 mm * Galvanized front wall with tensioning system for sliding curtains, height adjustable by approx. 400 mm * EDSCHA roof, sliding forward on aluminum roof girder profiles (screwed to front and rear wall) * 3 pairs of sliding stakes in the loading area * The body is hydraulically extendable to the left and right at the rear by approx. 750 mm * Sliding roof with pivoting portal crossbeam * Sliding curtain with approx. 700 mm reserve length, ratchet straps at approx. 600 mm intervals. Height O

Condition: new, maximum load weight: 38,500 kg, overall weight: 48,000 kg, axle configuration: 3 axles, total width: 2,540 mm, Equipment: ABS, Our complete vehicle inventory, including immediately and shortly available vehicles, can be found on our website. Selection of features. Complete equipment details upon request. EQUIPMENT: * Gooseneck, length approx. 4,100 mm, with central beam * Extendable load area, length approx. 9,400 mm, with 350 mm x 10° rear bevel and integrated hook-in rail for use with separate aluminum loading ramps * Pneumatic locking system with conical locking pin and reinforced locking positions; supply lines are protected within the extendable beams and automatically adjust to the selected platform length * Technical fifth wheel load: 18,000 kg * Suitable for tractor units: 4 x 2 and 6 x 2 * TPMS Tire Pressure Monitoring System in accordance with ECE R 141 * BPW axles and suspension, all axles hydro-mechanically forced steered, mounted on turntables * Technical axle load: 12,000 kg per axle * Air suspension with lift/lower valve * 235/75 R 17.5 3PMSF twin tires, manufacturer of our choice * ASPÖCK-UNIBOX * 3 kW electro-hydraulic power unit for hydraulic operations (without supply connections installation on the tractor unit) * 4 pairs of recessed lashing rings in the outer frame of the gooseneck: - The first three pairs are flat (LC 10,000 daN) - The rear pair is fold-out (LC 10,000 daN) * 4 pairs of stake pockets recessed in the outer frame of the gooseneck for plug-in stakes approx. 100 x 50 mm * 2-inch king pin * Mechanical landing legs with 2-speed gearbox and crank; JOST Modul B, static test load approx. 50,000 kg * Wooden flooring approx. 32 mm thick, framed in aluminum omega profiles on the gooseneck and platform * 10 pairs of recessed, flat-mounted, foldable lashing rings in the outer frame of the load area * One pair of lashing rings (LC 10,000 daN) in front of the last axle and at the end crossmember of the trailer * All other lashing rings (LC 5,000 daN) * 6 pairs of stake pockets recessed in the outer frame of the load area for plug-in stakes approx. 100 x 50 mm * 1 spare wheel holder under the load area, right side when facing forward * 1 lockable stainless steel (INOX) toolbox, approx. 1,250 x 500 x 550 mm (L x W x H), mounted under the load area on the left when facing forward * Rear crossmember with bevel approx. 350 mm x 10° * Integrated hook-in rail for loose aluminum loading ramps at the rear crossmember * 1 pair of drop-down supports at the rear crossmember * Steering override from front and rear via cable remote control with single-track axle monitoring (no installation on tractor unit) * Round NATO socket at the front connection rail (Maeler & Kaege VG 96 917) * 1 LED work light on both left and right of front bulkhead, wired to the tractor unit’s connection rail * Locking positions at each 500 mm on the extension * Internal holder for stakes not in use, mounted to the inside of the gooseneck bulkhead * 4 wheel chocks with holder under the load bed * Galvanised extension sections for platform widening by approx. 230 mm per side (without wooden planks) * 1 LED work light on both left and right in front of the axles, wired to the connection rail for the tractor unit * 2 axle load gauges mounted on the left side, including axle load diagram * 1st axle with traction aid Dodpfjy Augdox Agrscg * Mountings for warning signs under the gooseneck as well as left and right at the rear crossmember * Acoustic warning signal when reversing * EU reflector at the rear of the vehicle

Condition: new, maximum load weight: 37,980 kg, overall weight: 48,000 kg, axle configuration: 3 axles, Equipment: ABS, You can find our complete vehicle stock, including immediately and short-term available vehicles, on our website. Excerpt from the equipment. Complete equipment details available on request. Dodpsy Aufmofx Agrscg Gooseneck: * Gooseneck with approx. 45° chamfered front corners and rear chamfer approx. 750 mm x 10° * 3 pairs of lashing rings (LC 5,000 daN) * Hardwood floor covering approx. 30 mm thick Loading platform (extendable version): * Loading platform in extendable version with rear chamfer approx. 1,000 mm x 8° * 6 pairs of lashing rings, foldable outwards (LC 5,000 daN) * 3 pairs of lashing rings, foldable outwards (LC 10,000 daN) * 1 pair of lashing rings installed flat at the front of the loading platform (LC 10,000 daN) * Cut-outs in the outer frame of the loading platform for attaching tension straps (LC 2,000 daN) * Hardwood floor covering approx. 48 mm thick, checker plate over the axles Landing legs: * JOST landing legs (mechanical) with two-speed gearbox for approx. 24 t lifting capacity (approx. 50 t test load) Tires: * Tires 235/75 R 17.5 3PMSF – brand of our choice TPMS: * TPMS tire pressure monitoring system according to ECE R 141. Data transmission to the towing vehicle via the standardized EBS interface in accordance with ISO 11992. For correct display, the towing vehicle must be able to receive and show this data. Axles: * BPW axles and suspension, 2 fixed axles, 1 trailing steering axle * Technical axle load: 12,000 kg each * Electromagnetic reverse lock, activated via reverse gear and manually * Air suspension with lifting and lowering valve * Axle tools Brake system: * Brake system according to EU regulations with EBS-E (2S2M), without connection lines to the tractor unit Steel construction: * Steel construction from high-strength fine-grain steels * Steel grades: S355J2+N/S355MC (yield strength 355MPa), S690QL/S700MC (yield strength 690MPa) Painting: * Entire steel structure is automatically shot blasted by blast wheel system after welding * Second blasting with corundum for optimal coating adhesion * Final coating with 2 layers of 2K topcoat, solid color in RAL 3002 Carmine Red, according to RAL system 841GL * Rims in silver-grey * Rear section metallized and painted in RAL 9010 (pure white) * Coating tested in salt spray test according to ISO 9227-NSS * Cavity sealing with special wax Electrical system: * Electrical system according to EU regulations, 24 Volt ASPÖCK-NORDIK lighting (ASS3) * All LED side marker lamps flash with the indicator * ASPÖCK-UNIBOX on the front junction strip with 24N, 24S & 15-pin sockets, connection as per ISO: 24N ISO-1185, 24S ISO-3731, 15-pin ISO-12098 Accessories included: * 2-inch king pin * One galvanized steel front wall, approx. 400 mm high * One spare wheel holder in front of the headboard * Yellow-red air couplings on the galvanized front junction strip * 4 wheel chocks with holder at the headboard * Mounting at the rear of the gooseneck for ALU access ramps * Galvanized folding supports under the loading platform chamfer * Gooseneck and rear panel each with a bracket for warning signs including socket left and right * Axle load gauge including load diagram * On the gooseneck, plug-in aluminum side panels and rear wall, approx. 2,440 x 400 mm (L x H). The rear galvanized plug-in stanchions are removable. (Body length approx. 2,560 mm) * One galvanized toolbox, integrated in the chamfered gooseneck * 3 pairs of WADER C

Condition: refurbished (used), functionality: fully functional, machine/vehicle number: YAFTL409100010512, Year of construction: 2010, For sale: Faymonville 4-axle semi-trailer (year 2010), telescopic, in like-new condition. The unit has undergone a comprehensive overhaul at a specialized workshop and is fully ready for work, with no additional repairs required. ✅ ADVANCED STEERING SYSTEM: Equipped with permanent hydraulic steering, active both when driving forward and in reverse. Includes a wired remote control for manual axle operation during maneuvering. Dodpfxey Eclto Agrscg ✅ COMPLETE SANDBLASTING AND PAINTING: Chassis restored and fully protected. ✅ NEW DECKS: Lumber and inserts recently replaced, never loaded after refurbishment. ✅ FULL MAINTENANCE: Mechanics, brakes, and hydraulic system (ramps and steering) overhauled. ✅ WORK-READY: No further investment needed. Periodic inspection carried out on 27.02.2026. TECHNICAL DATA SHEET: Axles: 4 axles (1st liftable / 2nd–3rd–4th steering axles). Telescopic: Single extension (+7.20 m). Total length up to 21 meters. Payload capacity: 25,600 kg. Accessories: Double hydraulic ramps, front winch.

Condition: excellent (used), axle configuration: > 3 axles, permissible axle load (axle 1): 12,000 kg, permissible axle load (axle 2): 12,000 kg, permissible axle load (axle 3): 12,000 kg, loading space length: 13,600 mm, loading space width: 2,540 mm, loading space height: 1,550 mm, total length: 13,600 mm, total width: 2,540 mm, total height: 1,550 mm, suspension: air, tire size: 275 / 70 R22.5 – Good Year, color: red, Year of construction: 2024, Color: Red Payload Capacity: 60,800 kg Extendable Main Features Dsdpfsv I Dqqjx Agrecg Manufacturer: Faymonville Model: F-S44-1BBY Triple Extendable Flat Bed Chassis Number: YAFSR4009S0036724 Year: NEW / Unused Weights / Payload Kingpin Load: 28,000 kg Axle Load: 12,000 kg per axle Total Axle Load: 48,000 kg Gross Vehicle Weight (GVW): 76,000 kg Unladen Weight: 15,200 kg Payload Capacity: 60,800 kg Axles Axle Brand: BPW Air Suspension All Axles with Hydraulic Steering WABCO Braking System with EBS Tyres: 275 / 70 R22.5 – Goodyear Load Index: 148/145M Dimensions Length: 13,600 mm Extensions: 7,200 mm + 7,400 mm + 7,600 mm Max. Extended Length: 35,800 mm Loading Platform Width: 2,540 mm Height: 1,550 mm (+/- 100 mm) Additional Information High Resistance Metalized Steel Construction NATO Plug Lashing Rings Stake Pockets Wooden Loading Floor Mechanical Landing Gear Electrohydraulic Pump for Trailer Functions Spare Wheel Rear Bumper with Lighting Kingpin 2.0” and 3.5” Central Greasing System with 2 BEKAMAX Pumps = Additional Information = General Information Year of Manufacture: 2024 Axle Configuration Tyre Size: 275 / 70 R22.5 – Goodyear Axle Brand: BPW Suspension: Air Suspension Rear Axle 1: Twin Tyres; Max. Axle Load: 12,000 kg; Steered; Tyre Tread (left inner/outer, right inner/outer): 100% each Rear Axle 2: Twin Tyres; Max. Axle Load: 12,000 kg; Steered; Tyre Tread (left inner/outer, right inner/outer): 100% each Rear Axle 3: Twin Tyres; Max. Axle Load: 12,000 kg; Steered; Tyre Tread (left inner/outer, right inner/outer): 100% each Rear Axle 4: Twin Tyres; Max. Axle Load: 12,000 kg; Steered; Tyre Tread (left inner/outer, right inner/outer): 100% each Weights Unladen Weight: 15,200 kg Payload: 60,800 kg GVW: 76,000 kg Functionality Loading Platform Height: 155 cm Extendable Body: Yes Condition Technical Condition: Very Good Optical Condition: Very Good Further Information Please contact Stefan Schaapveld for more information.

Condition: good (used), axle configuration: 3 axles, permissible axle load (axle 1): 10,500 kg, permissible axle load (axle 2): 10,500 kg, permissible axle load (axle 3): 10,500 kg, first registration: 11/2022, total length: 13,900 mm, total width: 2,550 mm, total height: 2,400 mm, suspension: air, tire size: 235/75 17.5, wheelbase: 2,300 mm, Year of construction: 2022, Equipment: ABS, = Additional Options and Equipment = - EBS (Electronic Braking System) - Air suspension rear - Spare wheel = Remarks = - Faymonville / Max Trailer 3-axle low loader (Type: MAX100) - Load platform dimensions: Length 930 cm x Width 254 cm - Extendable to: 1280 cm (+350 cm) - Loading height: 91 cm - Lashing rings - Wheel well - Extension pieces - Gooseneck dimensions: Length 252 cm x Width 247 cm x Height 40 cm - Loading height: 149 cm - 2 ALTEC loading ramps made of aluminium (Type: VFR120) - Dimensions: Length 235 cm x Width 47 cm - Maximum gradient: 30% (16.5°) - 10.5-tonne axles! Dsdpfjyztt Tox Agrjcg - 18-tonne kingpin load! - 49.5 tonnes gross technical weight capacity! - AS NEW CONDITION! - Always stored indoors! - Only 20,000 km driven! = Further Information = Axle configuration Tyre size: 235/75 17.5 Axle brand: BPW Suspension: Air suspension Rear axle 1: Twin tyres; Max. axle load: 10,500 kg; Tyre tread left inner: 70%; Tyre tread left outer: 70%; Tyre tread right inner: 70%; Tyre tread right outer: 70% Rear axle 2: Twin tyres; Max. axle load: 10,500 kg; Tyre tread left outer: 80%; Tyre tread right outer: 80% Rear axle 3: Twin tyres; Max. axle load: 10,500 kg; Steered; Tyre tread left inner: 70%; Tyre tread left outer: 70%; Tyre tread right inner: 70%; Tyre tread right outer: 70% Weights Unladen weight: 10,069 kg Payload: 35,931 kg Gross vehicle weight: 46,000 kg Maintenance, History and Condition Number of owners: 1 APK (Main technical inspection): valid until 11/2026 Technical condition: good Visual condition: good Identification Registration number: OT-87-PP Product Safety Manufacturer: Clean Mat Trucks B.V. Wageningsestraat 17 6673DB ANDELST, NL

Condition: used, empty load weight: 11,550 kg, maximum load weight: 30,450 kg, overall weight: 42,000 kg, axle configuration: 3 axles, first registration: 01/2019, next inspection (TÜV): 01/2027, loading space length: 13,450 mm, loading space width: 2,540 mm, loading space height: 700 mm, loading space volume: 23 m³, suspension: air, color: red, Year of construction: 2018, gearing type: mechanical, Equipment: ABS, Unladen weight: 11,550 kg, permissible total weight: 42,000 kg, loading area (L W H): 13,450 mm x 2,540 mm x 700 mm, loading area volume: 23 m³, air suspension, lift axle: 1st axle, electronic braking system (EBS), trailing steering: 3rd axle, twin tires, minimum length 13.45 m, maximum length 18.20 m, unladen weight 11,550 kg, fifth wheel load 18,000 kg, total weight 48,000 kg, exemption permit DE, extendable, adjustable hydraulic ramps, 3rd axle forced steering, tires 235/75R17.5 twin, winch, TÜV valid until 01-2027, YAMT13XXXJ0102830, non-binding offer, errors and prior sale excepted. The illustration may not correspond to the offer. Dcodpfx Aey Dng Tjgreg

Condition: used, overall weight: 39,500 kg, axle configuration: 3 axles, first registration: 07/2022, loading space length: 13,400 mm, loading space width: 2,540 mm, loading space height: 890 mm, Year of construction: 2022, Equipment: ABS, lfd 12389 LOW-LOADER MAX TRAILER 3-axle F-S43-1AAF/ AZB 4500 mm / STEERING AXLE Make/Manufacturer: MAX TRAILERS First registration: 07.2022 Dimensions: 13,400 x 2,540 x 890 mm Gross vehicle weight: 49,500 kg Unladen weight: 10,284 kg Payload: approx. 38,000 kg Kingpin load: 18,000 kg Air suspension with lift/lower function Drum brakes Dcjdpfxey Ag Ado Agrog ABS EBS Mileage: 142,000 km Axle make: BPW 10.5 t Lift axle Steering axle Trailing steering axle Lashing rings Superstructure paintwork: Red Chassis paintwork: Galvanised / Red Tyres: 12-fold Tyre tread depth: 7 - 10 mm Tyres (rear axle): 235/75 R 17.5 MAX = FAYMONVILLE MAX 100 Ideal for concrete slabs / timber walls / precast concrete elements, etc. ASH 1200 mm / hardwood floor Rear loading edge: 890 mm Lowered: 840 mm Container locks for: 1 x 40/30 ft and 20 ft Incl. 4 x twistlocks Stake pockets & 5 t lashing rings on load area Extendable by 4,500 mm in 500 mm increments Centre platform can also be removed Trailing steering axle Aluminium air tank / hot-dip galvanised TOP CONDITION! Currently sample images as of 06.2025 All information provided without guarantee, subject to prior sale! Should you have any questions about this or other vehicles, please call us. If you have any questions regarding this or another trailer / vehicle, please call us.

Condition: used, maximum load weight: 35,500 kg, overall weight: 45,000 kg, axle configuration: 3 axles, first registration: 10/2007, loading space length: 13,500 mm, loading space width: 2,500 mm, loading space height: 1,500 mm, total width: 2,550 mm, total height: 3,200 mm, Equipment: ABS, Extendable trailer from 7,700 mm to 21,300 mm total length, electric hydraulic pump, hand pump for hydraulic system, NATO jump start socket, 3 center stake pocket rails on the loading area, 10 stake pockets per side, 10 pairs of heavy-duty recessed lashing rings in the floor, rotating beacon / rear, JOST landing gear, ABS, EBS, axle(s), hydraulically steered axles, drum brake system, air suspension with lift/lower device, central lubrication system. Vehicle may be covered with advertising wrap and/or labeled. SI86629 Our offer generally does not include a new TÜV inspection. If a new TÜV inspection is required, we will be happy to provide an offer from our partner workshops! Vehicle may be covered with advertising wrap and/or labeled. Our general terms and conditions of delivery and payment apply. Dsdpfx Agoyumi Hsrjcg We are happy to provide you with a financing or leasing offer for this item. Please contact us!

Condition: used, color: grey, Year of construction: 2023, Faymonville Combi-Z-10 Gooseneck: V-30-2.70-3-U. 2 axles: PA-M-2-17.5-245-1.50-2.85F. 2 axles: PA-M-2-17.5-245-1.50-2.85F. 6 axles: PA-M-6-17.5-245-1.50-2.85H. Year: 2024. Ton axle load. Weight: Payload: Maximum weight: Kingpin load: 30,000 kg. Powerpack-HA-1-EU-STZ Hatz. Aluminium side boards on neck. 2 x extendable: Djdpeyyv U Djfx Agrjcg - 1: 7,500 mm - 2: 7,000 mm Total extension: 14.5 metres. 2 x spare tyres. Radio remote control. Hydraulic suspension. Dimensions: Neck: L: 4,050 mm W: 2,540 mm H: 2,000 mm Kingpin height: 1,400 mm Main deck: L: 16,500 mm W: 2,850 mm H: 1,060 mm Tyres: 245/70R17.5, 90% tread. New condition! ID No: 118. The General Terms and Conditions of Heinhuis apply to all advertisements, offers, and quotations published by Heinhuis, as well as to all contracts concluded by Heinhuis and the negotiations leading up to them. By responding in any form, you accept the applicability of the Heinhuis General Terms and Conditions and declare that you have taken note of these General Terms and Conditions. Our prices are net export prices. = Further information = Year of manufacture: 2023 Price: On request = Company information = For more information: WhatsApp:

Condition: good (used), axle configuration: > 3 axles, permissible axle load (axle 1): 8,000 kg, permissible axle load (axle 2): 8,000 kg, permissible axle load (axle 3): 8,000 kg, first registration: 11/2017, total length: 135,000 mm, total width: 2,540 mm, total height: 780 mm, color: black, Year of construction: 2017, Equipment: ABS, = Additional options and equipment = - Air suspension = Further information = Axle configuration Rear axle 1: Max. axle load: 8,000 kg Rear axle 2: Max. axle load: 8,000 kg; Steered Rear axle 3: Max. axle load: 8,000 kg; Steered Rear axle 4: Max. axle load: 8,000 kg; Steered Weights Empty weight: 14,800 kg Payload: 42,200 kg Gross vehicle weight (GVW): 57,000 kg Condition Technical condition: good Visual condition: good Damages: none Dsdoyx Hwyepfx Agrocg Financial information Price: On request Further information Please contact David F Middelman for more information.

Condition: used, empty load weight: 11,200 kg, maximum load weight: 36,800 kg, overall weight: 48,000 kg, axle configuration: 3 axles, first registration: 10/2025, loading space length: 9,300 mm, loading space width: 2,540 mm, loading space height: 860 mm, suspension: air, tire size: 235/75 R 17.5, color: grey, Year of construction: 2025, Equipment: ABS, For every used trailer, you will receive a current and complete inspection and functionality report. Gooseneck: - Gooseneck with rear bevel of approx. 750 mm x 10° - 3 pairs of lashing rings (LC 5,000 daN) - Hardwood flooring 30 mm thick Extendable loading area: - Telescopic loading area with rear bevel approx. 1,000 mm x 8° - 1 pair of built-in wheel recesses in front of the axles (approx. 2,850 x 970 x 400 mm) - Wheel recesses with 15 x 15 mm square climbing bars and lower-area widenings - Between the 1st and 2nd axle, 1 pair of fixed wheel recesses, approx. 1,610 x 970 x 400 mm - Incl. 3-piece removable galvanized covers over the wheel recesses (width 670 mm) – max. point load 5 t each - Recess in the bevel, extending into the platform, for excavator dipper stick approx. 2,900 x 750 x 210/290 mm - 1 pair of horizontal lashing rings at the front of the loading area (LC 10,000 daN) - 5 pairs of outward folding lashing rings (LC 5,000 daN) - 2 pairs of outward folding lashing rings (LC 10,000 daN) - 2 pairs of lashing rings in the excavator dipper recess (LC 5,000 daN) - Cutouts in the outer frame for attachment of tensioning straps (LC 2,000 daN) Ramps: - One pair of galvanized two-part steel ramps, approx. 2,750 + 1,400 x 800 mm, with approx. 48 mm thick hardwood covering - Ramps with hydraulically foldable ramp sections, hydraulic lifting mechanism, and hydraulically adjustable - Maximum load per pair: 40,000 kg Axles and Tyres: Dsdpoyylduefx Agrscg - BPW axles and suspension, 2 axles fixed, 1 trailing axle - Technical axle load: 12,000 kg - Electromagnetic reversing lock, activated by reversing gear and manually - Air suspension with raise/lowering valve - Axle tools - TPMS tyre pressure monitoring system according to ECE R 141 - Tyres 235/75 R17.5 3PMSF Accessories included: - Bracket for warning signs on the gooseneck and rear left and right, with socket - 1 spare wheel with holder in front of the front wall - 2" king pin - One galvanized steel front wall approx. 400 mm high - Yellow-red air couplings on the galvanized connector strip at the front - 4 wheel chocks with holders - Galvanized extendable widenings approx. 230 mm per side - Galvanized folding supports under the rear bevel of the loading area - Cover plates for bridging the gap between ramps and loading area - White reflective tape to EU regulations on sides and extension, red on rear - Electro-hydraulic unit at the rear, under the loading area - European reflective signs (red-yellow) at rear of trailer - Four warning signs extendable by around 400 mm, approx. 423 x 423 mm with position light - Bracket for rotating beacon on warning signs - Plug-in ALU side and rear panels on the gooseneck, approx. 2,440 x 400 mm - Removable galvanized rear stanchions (body length approx. 2,560 mm) - 2 pairs of WADER container pockets in the loading area for 20ft or 30ft containers - 3 pairs of stanchion sockets (100 x 50 mm) in the outer frame of the loading area - Removable galvanized intermediate table with 1 pair of WADER container pockets - 20 x 20 mm square climbing bars every 200 mm on the outer frame of the loading area’s rear bevel - Anti-slip sand coating applied to checker plates on the gooseneck and loading area - 80 km/h speed stickers on rear and both sides - Load pressure gauge for determining axle loads, including load chart

Condition: excellent (used), first registration: 07/2021, loading space length: 134,500 mm, loading space width: 2,550 mm, loading space height: 770 mm, total length: 13,450 mm, total width: 2,550 mm, total height: 770 mm, Year of construction: 2021, Equipment: ABS, = Additional options and equipment = - Air suspension = Further information = Unladen weight: 8,520 kg Payload: 31,000 kg Gross vehicle weight: 50,900 kg Dcjdpoyxrdxefx Agreg Loading height: 77 cm Technical condition: very good Visual condition: very good Price: On request

Condition: used, Year of construction: 2005, Faymonville STBZ-2WAA. Year of manufacture: 2005. 10.5-ton SAF axles. Unladen weight: 11,760 kg. Load capacity: 27,240 kg. Gross vehicle weight: 39,000 kg. Kingpin load: 18,000 kg. Hydraulic system compatible with NATO. Radio remote control. Hydraulic gooseneck. 2x extendable: - 1st extension: 5.50 meters. - 2nd extension: 5.10 meters. Total extendable length: 10.6 meters. Air suspension. Power steering on 2 steering axles. 3 removable floor panels. Dcjdpjyxlhqefx Agreg Dimensions: Neck: Length: 3,750 mm. Width: 2,480 mm. Height: 1,600 mm. Kingpin height: 1,300 mm. Floor: Length: 6,850 mm. Width: 2,550 mm. Height: 570 mm. Floor thickness: 350 mm. Rear of the trailer: Length: 2,800 mm. Width: 2,550 mm. Height: 950 mm. Tyres: 245/70R17.5, tread depth 40%. ID No: 642. The General Terms and Conditions of Heinhuis apply to all advertisements, offers and quotations from Heinhuis, all agreements entered into by Heinhuis and the negotiations leading up to them. By responding in any form, you accept the applicability of the General Terms and Conditions of Heinhuis and confirm that you have taken note of these General Terms and Conditions. Our prices are net export prices. = More information = Year of manufacture: 2005 Unladen weight: 11,760 kg Load capacity: 27,240 kg Gross vehicle weight: 38,999 kg = Company information = For more information: WhatsApp:

Condition: used, color: red, Year of construction: 2016, Faymonville F-S43-1EJB. Year: 2016. 9-ton BPW axles. Max permissible weight: 45,000 kg. Kingpin load: 18,000 kg. EBS, ABS, ALB systems. Hydraulic operates on NATO standard. Hydraulic suspension. Length: 9,500 mm. Tyres: 385/65R22.5, 80% tread remaining. ID No: 521. The General Terms and Conditions of Heinhuis apply to all advertisements, offers, and quotations from Heinhuis, all agreements entered into by Heinhuis, and the negotiations preceding them. By responding in any form, you accept the applicability of Heinhuis' General Terms and Conditions and declare that you have taken note of these General Terms and Conditions. Our prices are net export prices. Dcsdpfjyxldlox Agrsg = More information = Year of manufacture: 2016 Gross vehicle weight: 45,000 kg = Company information = For more information: WhatsApp:

Condition: used, empty load weight: 10,650 kg, maximum load weight: 40,310 kg, overall weight: 50,960 kg, axle configuration: > 3 axles, first registration: 10/2024, loading space length: 9,300 mm, loading space width: 2,540 mm, loading space height: 760 mm, suspension: air, tire size: 205/65 R17.5, color: grey, Year of construction: 2024, operation weight: 10,650 kg, Equipment: ABS, For every used semi-trailer, you receive a current and complete inspection and functional report. Gooseneck: Dcsdpfx Agoxfa E Ujrog - Gooseneck with 30 mm hardwood flooring - Gooseneck with straight rear design - 3 pairs of lashing rings (LC 5,000 daN) Loading surface: - Extendable loading platform - 5 pairs of folding outward lashing rings (LC 5,000 daN) - 3 pairs of folding outward lashing rings (LC 10,000 daN) - 1 pair of flat lashing rings at the front of the loading platform (LC 10,000 daN) - Cut-outs in the outer frame of the loading platform for attaching tension belts (LC 2,000 daN) - Hardwood flooring approx. 48 mm thick, with chequer plate floor above the axles Axles and tyres: - BPW axles, two rigid and two self-steering trailing axles - Air suspension, with drum brake, with lift/lower function - The self-steering axles can be locked electromagnetically via reverse gear or manually - Axle tools - Tyres 205/65 R17.5 Braking system: - WABCO braking system according to EU regulations with EBS-E (4S3M) Steel construction: - Steel structure made from high-strength fine-grain steels - Steel qualities: - S355J2+N/S355MC (yield strength 355MPa) - S690QL/S700MC (yield strength 690MPa) Paintwork: - Premium and durable corrosion protection of the standard shot-blasted welded frame guaranteed by a 2-component (2K) zinc dust primer - High-quality 2-component (2K) top coat, single-colour, in Nova Gray Accessories included: - Spare wheel carrier in front of the bulkhead - 2" king pin - Galvanised steel bulkhead approx. 400 mm high - Yellow-red air couplings on the galvanised front connector strip - 4 wheel chocks with holder on the bulkhead - Galvanised folding supports under the chamfer of the loading platform - Bracket for rotating beacon at the rear of the trailer - Galvanised extendable widening devices, extendable by approx. 230 mm per side - White reflective tape to EU standards on the sides, on the extension, and red at the rear - One mounting bracket each for warning signs, including socket, on the gooseneck and rear plate left and right - One mudflap at the rear - European reflector plates (red-yellow) at the rear of the trailer - TPMS tyre pressure monitoring system according to ECE R 141 - Removable ALU sidewalls and rear wall on the gooseneck approx. 2,440 x 400 mm - Rear galvanised plug-in stanchions are removable (body length approx. 2,560 mm) - 7 pairs of WADER container pockets: 1x 20ft container on the loading platform; 1x 40ft container on the loading platform; 1x 40ft container over the gooseneck; 2x 20ft containers - 7 pairs of stake pockets for 100 x 50 mm stanchions in the outer frame of the loading platform - Lift axle on the front axle with control via TEBS E depending on axle load and current payload status - Movable hanging bar for ALU loading ramps at the rear of the vehicle - Anti-slip sand coating painted onto the chequer plates on the gooseneck and loading platform - Four extendable warning signs approx. 423 x 423 mm, extendable by approx. 400 mm, with positioning light - Mounting bracket for rotating beacon on the warning signs - 80 km/h speed stickers at the rear and on both sides - Load gauge for axle load determination including load diagram - HRM metallisation (High Resistance Metallisation) of the outer frame - Complete steel structure shot-blasted, then specified visible surfaces finished with ZINACOR 850 metallisation (Zinc 85% - Alu 15%) by hot-refining

Condition: used, empty load weight: 13,200 kg, maximum load weight: 52,800 kg, overall weight: 66,000 kg, axle configuration: > 3 axles, first registration: 06/2025, loading space length: 9,300 mm, loading space width: 2,540 mm, loading space height: 860 mm, suspension: air, tire size: 245/70 R 17,5, color: grey, Year of construction: 2025, Equipment: ABS, With every used semitrailer, you receive a current and comprehensive inspection and function report. Gooseneck: - Gooseneck with rear chamfer of approx. 750 mm x 10° - 3 pairs of lashing rings (LC 5,000 daN) - 30 mm thick hardwood flooring Extendable load platform: - Load platform in extendable design with rear chamfer approx. 1,000 mm x 8° - 5 pairs of fold-out lashing rings (LC 5,000 daN) - 3 pairs of fold-out lashing rings (LC 10,000 daN) - 1 pair of flat-mounted lashing rings at the front of the platform (LC 10,000 daN) - Cutouts in the outer frame of the platform for attaching tension straps (LC 2,000 daN) - Approx. 48 mm thick hardwood flooring; checker plate over the axles Axles and tyres: - BPW axles and suspension, 1st axle fixed, all other axles hydro-mechanically forced steered - Technical axle load: 12,000 kg - Air suspension with lift and lowering valve - Tyres: 245/70 R 17.5 - TPMS tyre pressure monitoring system in accordance with ECE R 141 Two-piece steel ramps: - One pair of galvanised two-piece steel ramps, approx. 2,750 + 1,400 x 800 mm with 48 mm thick hardwood covering - Ramps with hydraulically folding ramp sections, hydraulic lifting mechanism, and hydraulically adjustable - Maximum load capacity per pair: 40,000 kg Accessories included: - 2" king pin - One galvanised steel front wall, approx. 400 mm high - Yellow-red air couplings at the galvanised connection rail at the front - 4 wheel chocks - One spare wheel - Electro-hydraulic power unit - Remote steering from the front and rear using wired remote control with push buttons, with single-track axle control - Mount at the rear section of the gooseneck for aluminium drive-on ramps - European reflective panels (Red-Yellow) at the rear of the semitrailer - White reflective tape as per EU regulations on sides, on extension, and red at the rear - On the gooseneck and ramps, left and right, each with a bracket for warning signs and socket - One holder for a beacon at the rear of the semitrailer - Galvanised folding supports under the chamfered section of the platform - Control valves for the ramps mounted on the right side of the semitrailer - Cover plates to bridge the gap between ramps and platform - Central lubrication system BEKAMAX (Pico) with standard grease NLGI-2 - On the gooseneck, clip-on aluminium drop sides and rear wall, approx. 2,440 x 400 mm - Rear galvanised plug-in posts are removable (structure length approx. 2,560 mm) - One INOX toolbox 1,350 x 400 x 400 mm mounted on the gooseneck, box covers oil filler plug - 4 pairs of WADER container pockets on platform for one 20ft, two 20ft, 40ft or 45ft container - 7 pairs of stake pockets for removable posts 100 x 50 mm on the outer frame of the platform - Galvanised extensions, extendable by approx. 230 mm per side - Square climbing strips 20 x 20 mm every 200 mm on the outer frame of the platform’s chamfer Dcsdpjyffd Dsfx Agreg - Lift axle on the front axle, controlled by TEBS E depending on current axle load and loading status - Four warning signs extendable by approx. 400 mm, approx. 423 x 423 mm with position light - Radio remote control for steering in addition to the wired remote, with indicator lights on receiver for single-track control - Non-slip sand coating painted on checker plate on the gooseneck and load platform - 80 km/h speed stickers at the rear and on both sides

Condition: new, overall weight: 78,000 kg, axle configuration: > 3 axles, loading space length: 8,800 mm, loading space width: 2,540 mm, loading space height: 850 mm, tire size: 245/70 R 17.5, color: grey, Equipment: ABS, Gooseneck: • Gooseneck in SNT design for optimizing load platform length, approx. 3,700 mm long, with rear chamfer approx. 1,000 mm x 10° • Suitable for tractor units: 4 x 2, 6 x 2 and 6 x 4 Load Platform: • Extendable load platform, approx. 8,800 mm long with rear chamfer of approx. 500 mm x 10° • Recess in the load platform and chamfer area for receiving excavator dipper stick, approx. 3,950 x 580 x 370/450 mm Ramps: • Pair of two-piece steel ramps, approx. 4,350 mm long and 900 mm wide • Hydraulic foldable ramp ends • Ramps can be hydraulically moved individually by approx. 235 mm outward and approx. 215 mm inward • Hardwood covering on the chamfered section of the load platform • Ramps with hardwood covering • 20 x 30 mm square climbing bars, spaced approx. every 200 mm on the outer frame of the ramp Axles and Tyres: • TWINAXLE-II independent suspension with BPW axle stub, 1st axle steering, all other axles forced steered via hydromechanical system • 1st axle with electro-magnetic reverse lock, activated automatically in reverse gear or manually • Technical axle load: 12,000 kg • Hydraulic axle compensation, hydraulic cylinders with shut-off valves • Tyres: 245/70 R 17.5 Dcjdpervw U Sofx Agreg • TPMS tyre pressure monitoring system according to ECE R 141 Accessories included: • Detachable steel front wall, approx. 400 mm high • 4 wheel chocks with holders • Yellow-red air couplings on the front connection strip • 3 kW electro-hydraulic power pack for operation of hydraulic functions, except hydraulic winches • 1 spare wheel • 2 pairs of screw-in lashing rings • 1 pair of horizontal lashing rings at the rear of the gooseneck • On the gooseneck: 1 pair removable ALU side boards, approx. 400 mm high, anodized • On the gooseneck: removable ALU rear wall, approx. 400 mm high, anodized • Approx. 40 mm thick hardwood covering above the gooseneck, checker plate covering over the king pin • 3.5" king pin • Gooseneck guide plate for fifth wheel, approx. 500 mm wide • Load platform locking with conically welded locking profiles every 250 mm • Includes pre-tensioning plate • 1 pair of lashing rings on the front cross member • 8 pairs of recessed, fold-out lashing rings in the outer frame of the load platform • Extendable (galvanized) outriggers, approx. 230 mm each side • 1 pair of built-in open wheel recesses to the extension, approx. 700 x 410 mm, in the load platform in front of the 1st axle • Wheel recesses with steel plating and 15 x 15 mm square climbing bars, approx. every 200 mm • 1 pair of built-in wheel recesses, approx. 1,480 x 700 x 410 mm, in the load platform between the 1st and 2nd axles • Wheel recesses with 15 x 15 mm square climbing bars and extensions in the lower area • ALU covers for the wheel recesses between the 1st and 2nd axles, usable as widening planks • 1 pair of mechanical rear supports • 20 x 30 mm square climbing bars, spaced approx. every 200 mm on the outer frame of the chamfered load platform • Central lubrication system with 1 pump, brand BEKAMAX, for standard grease as per NLGI-2 • Radio and cable remote control, with 2 indicator lights on the receiver for single-track control • WABCO Smart Board System • Smart Board equipped with odometer • 4 warning signs, approx. 423 x 423 mm, extendable by approx. 400 mm, including 2 marker lights and holders for beacon

Condition: used, maximum load weight: 34,400 kg, overall weight: 45,000 kg, axle configuration: 3 axles, first registration: 09/2015, loading space length: 9,530 mm, loading space width: 1,565 mm, loading space height: 1,650 mm, total width: 2,550 mm, total height: 2,800 mm, Equipment: ABS, Concrete inner loader, loading length: 9530 mm, loading width: 1,565 mm, angle profiles in the loading area for pallet accommodation, hydraulic load securing, 6 heavy-duty lashing rings per side, NATO jump-start socket, ABS, EBS, BPW Eco axle(s), drum brake system, front drop supports, vehicle may have advertising stickers and/or lettering. SI86628 Our offer generally does not include new TÜV inspection. If a new TÜV inspection is desired, we are happy to provide you with an offer from our partner workshops! Vehicle may be provided with advertising stickers and/or lettering. Our general terms of delivery and payment apply. Dcsdpsymu Iuofx Agrjg We are happy to create a financing or leasing package for this item. Please contact us!

Condition: new, overall weight: 49,500 kg, axle configuration: 3 axles, loading space length: 9,700 mm, loading space width: 2,540 mm, loading space height: 890 mm, suspension: air, tire size: 235/75 R 17.5, color: grey, Equipment: ABS, Gooseneck: - Gooseneck in SNT design to optimize the loading deck length, approx. 3,700 mm long, rear end with chamfer approx. 1,000 mm x 6° Dsdpfxeyw Sako Agrscg - For tractor units: 4 x 2 and 6 x 2 Loading Deck: - Loading deck, approx. 9,700 mm long with hydraulically folding and lowering rear section, plus hydraulically liftable front section for driving onto the gooseneck Axles and Tyres: - BPW axles and suspension, 1st and 2nd axles fixed, 3rd axle self-steering - 3rd axle with electro-magnetic reverse lock, activated via reverse gear and manual switch - Technical axle load: 12,000 kg - Air suspension with lift and lower valve - 235/75 R 17.5 3PMSF, twin tyres - TPMS tyre pressure monitoring system according to ECE R 141 BPW Auto Reverse Control: - Electrohydraulic auxiliary steering for self-steering axle of 3-axle assembly - Automatic control of the self-steering axle when reversing using a gyroscope sensor - Manual control for steering in forwards and reverse, via separate radio remote control - Manual operation enabled up to 10 km/h - System supplied via a separate electro-hydraulic unit Included Accessories: - Removable steel front wall, approx. 400 mm high - 3 kW electro-hydraulic power unit - Outer beams on the gooseneck with mounting holes for bolted lashing rings - First hole approx. 200 mm from the front, then every 400 mm - One mounting hole in the upper rear area of the outer beams for a bolted lashing ring - On the gooseneck and rear chamfer: grating floor with 5 mm steel reinforcement - 2" kingpin - Guide plate on the gooseneck for the fifth wheel, approx. 500 mm wide - Round NATO socket on the front interface (Maeler & Kaege VG 96 917) - On the gooseneck: 1 pair of removable ALU sidewalls, approx. 400 mm high, anodized - 4 wheel chocks - Electric cable winch, approx. 5,400 kg pulling force, with radio remote control - Wire rope approx. 24 m long, rope ø approx. 9.5 mm, incl. rope press roller - Winch mounted front inside the gooseneck - Continuous grating floor with 5 mm steel plate reinforcement for additional strength, designed for point load: - on the lift bed - on the loading deck - on the hydraulically lowerable rear section - Painted sand coating on the gooseneck cover plates and in the transition areas between neck and lift bed, lift bed and loading deck, and loading deck and ramps - 1 spare wheel - Hydraulic lift bed, approx. 2,500 mm long, load capacity in raised position while driving: 9,000 kg - Hydraulic cylinders equipped with load-holding valves - Cut-outs in the outer frame of the loading deck and lift bed for inserting tensioning straps - Extensive lashing points - Hydraulic rear section lowerable for loading/unloading and liftable for reducing overall length - Load capacity when horizontal while driving: 10,000 kg - Reduction of overall length when raised: 2,350 mm - Painted sand coating on the complete ramp except extendable galvanized part - Hydraulically extendable rear extensions for loading/unloading - Radio remote control: - Operation of the hydraulic lift bed - Operation of the hydraulic lift of the rear extension - Operation of the hydraulic extension of the rear extension - 1st axle with starting aid - Central lubrication system with 1 pump - 4 extendable warning panels, approx. 423 x 423 mm

Condition: new, overall weight: 49,500 kg, axle configuration: 3 axles, loading space length: 9,700 mm, loading space width: 2,540 mm, loading space height: 890 mm, suspension: air, tire size: 235/75 R 17.5, color: grey, Equipment: ABS, Gooseneck: - Gooseneck in SNT design for optimizing the loading platform length, approximately 3,700 mm long, with a rear chamfer approximately 1,000 mm x 6° - For tractor units: 4 x 2 and 6 x 2 Dcjdpfsyw R Srex Agrjg Loading Platform: - Loading platform, approximately 9,700 mm long, with hydraulically folding and tilting rear, including a hydraulically liftable front section for access onto the gooseneck Axles and Tyres: - BPW axles and suspension, 1st and 2nd axles fixed, 3rd axle steered - 3rd axle with electro-magnetic reversing lock, activated via reverse gear and manually - Technical axle load: 12,000 kg - Air suspension with lift and lower valve - 235/75 R 17.5 3PMSF twin tyres - TPMS tyre pressure monitoring system according to ECE R 141 Included Accessories: - Removable steel front wall, approx. 400 mm high - Yellow-red air couplings on the front connection panel - 3 kW electro-hydraulic unit for hydraulic operations, except for hydraulic winches - External gooseneck beams with mounting holes for bolted lashing rings - First hole approx. 200 mm from the front, then every approx. 400 mm - 2 pairs of screw-in lashing rings included - One mounting hole in the rear upper area of the external gooseneck beams for a bolted lashing ring - Grating surface with 5 mm steel reinforcement on the gooseneck and rear chamfer - 2" kingpin - Gooseneck guide plate for fifth wheel, approx. 500 mm wide - Round NATO socket on front connection panel (Maeler & Kaege VG 96 917) - 1 pair of removable ALU side boards, approx. 400 mm high, anodized, mounted on the gooseneck - 4 wheel chocks - Electric winch, approx. 5,400 kg pulling force, with radio remote control - Steel cable approx. 24 m long, cable diameter approx. 9.5 mm, including cable pressure roller - Winch installed at the front inside the gooseneck - Plastic cover for the winch - Mechanical landing legs with 2-speed gearbox and crank - JOST Modul B – static test load = 50,000 kg - Continuous grating surface with 5 mm steel backing as additional reinforcement, designed for point loads: - on the lift bed - on the loading platform - on the hydraulically lowerable rear section - Painted sand coating on the cover plates of the gooseneck, as well as in transition areas between neck and lift bed, lift bed and loading platform, and loading platform and ramps - 1 spare wheel with mounting adapter under the loading platform, right side in front of the axles - Hydraulic lift bed, approximately 2,500 mm long, load capacity while driving in raised position: 9,000 kg - Hydraulic cylinders fitted with load-holding valves - Cut-outs in the outer frame of the loading platform and lift bed for attaching lash straps - Extensive lashing positions - Hydraulic rear section lowerable for loading and unloading and raisable for shortening overall train length - Load capacity while driving in horizontal position: 10,000 kg - Reduction of overall train length in raised position: 2,350 mm - Painted sand coating on the entire ramp, except the extendable galvanized part of the ramp - Hydraulically extendable rear extension for loading and unloading Radio Remote Control: - Operation of the hyd. lift bed - Operation of the hyd. lifting mechanism for the rear extension - Operation of the hyd. sliding function of the rear extension - 1st axle with traction aid - Central lubrication system with 1 pump - 4 warning signs, approx. 423 x 423 mm, extendable

Condition: used, axle configuration: > 3 axles, first registration: 10/2006, total width: 2,850 mm, suspension: other, tire size: 285/70R19.5, color: black, Year of construction: 2006, Equipment: ABS, = Additional options and accessories = - Central lubrication system = Remarks = Dedpexbng Ejfx Agrjcg Faymonville Jeep Dolly D3 Year 10/2006. 1 x lift axle. 1 x friction-steered axle (trailing steering axle). Air suspension. Max. technical weight: 56,000 kg. Faymonville STBZ-5VA Year 10/2006. Pendle axle. Detachable gooseneck. Movable deck. Extendable bed: 400 cm. Load bed: 650 + 400 cm. 50,000 kg neck load capacity. Max. technical weight: 119,680 kg. = Further information = Axle configuration Tire size: 285/70R19.5 Brakes: drum brakes Front axle 1: twin tires; left inner tread: 15%; left outer tread: 60%; right inner tread: 60%; right outer tread: 60%; suspension: air suspension Front axle 2: twin tires; left inner tread: 30%; left outer tread: 30%; right inner tread: 40%; right outer tread: 60%; suspension: air suspension Front axle 3: twin tires; steered; left inner tread: 30%; left outer tread: 70%; right inner tread: 60%; right outer tread: 70%; suspension: air suspension Rear axle 1: twin tires; steered; left inner tread: 30%; left outer tread: 60%; right inner tread: 40%; right outer tread: 70%; suspension: hydraulic suspension Rear axle 2: twin tires; steered; left inner tread: 50%; left outer tread: 50%; right inner tread: 30%; right outer tread: 75%; suspension: hydraulic suspension Rear axle 3: twin tires; steered; left inner tread: 60%; left outer tread: 60%; right inner tread: 60%; right outer tread: 60%; suspension: hydraulic suspension Rear axle 4: twin tires; steered; left inner tread: 60%; left outer tread: 60%; right inner tread: 40%; right outer tread: 50%; suspension: hydraulic suspension Rear axle 5: twin tires; steered; left inner tread: 70%; left outer tread: 70%; right inner tread: 20%; right outer tread: 70%; suspension: hydraulic suspension Weights Unladen weight: 36,600 kg Payload: 83,080 kg Gross vehicle weight: 119,680 kg Financial Information Price: On request Identification Type number: STBZ-5VA + 3 AXLE JEEP DOLLY / E = Company information = ALL PRICES ARE NET FOR EXPORT. Joris Versteijnen (NL-DE-GB) Wouter Greutink (NL-DE-GB-ES-IT) We speak Russian. We make every effort to provide correct information, but no rights can be derived from the listed texts.

Condition: used, maximum load weight: 36,100 kg, overall weight: 49,000 kg, axle configuration: 2 axles, first registration: 10/2024, next inspection (TÜV): 10/2026, total width: 2,550 mm, Equipment: ABS, You can find our entire vehicle inventory, including immediately and short-term available vehicles, on our website. Excerpt from the equipment. Full equipment details available upon request. Gooseneck: * Gooseneck in SNT design, optimized for loading bed length, approx. 3,750 mm, hydraulically liftable/lowerable and detachable * Technical fifth wheel load: 25,000 kg * Suitable for tractor units: 4 x 2, 6 x 2 and 6 x 4 Low bed: * Low bed designed as a telescopic vessel bridge in a low construction with front extension and mechanical locking * Dimensions (L x W) approx. 6,850 mm x 2,540 mm * Supply lines are protected in the extendable beams and automatically adjust to the respective low bed length Axles and suspension: * PENDLE-AXLE * All axles hydro-mechanically forced-steered * Hose rupture valve for axle compensation * Cylinders with automatic RESET function * Hydraulic cylinders with shut-off valves and pre-plugs for securing in raised position * Technical axle load: 12,000 kg each * Hydraulic axle compensation * Tires: 245/70 R 17.5 * Rear chassis with closed outer frame, checker plate cover and continuous prism-shaped excavator trough approx. 1,250/700 x 505 mm, open at the rear Braking system: * WABCO EBS-E braking system compliant with EU regulations, without connection cable to the tractor unit Painting: * Trailer color, RAL 3002 Carmine Red Included accessories: * Plug-in front wall made of steel, approx. 400 mm high * 3 kW electro-hydraulic unit for controlling hydraulic functions, except for hydraulic winches, without installation of supply connections on the tractor unit * Outer beam of the gooseneck with mounting holes for bolted lashing rings. First hole approx. 200 mm from the front, then every approx. 400 mm. 2 pairs of screw-in lashing rings included (LC 5,000 daN) Dcsdpfx Agex Uvllorog * 1 lashing ring each left and right on the rear chamfer of the gooseneck (LC 6,000 daN) * 2-inch king pin * One locking position every approx. 500 mm on the extension * 1 pair of steel ramps with climbing bars and locking bolts to bridge the low bed hooks * 1 lashing ring each left and right on the front cross member (LC 10,000 daN) * Lashing rings with retaining spring every approx. 1,200 - 1,300 mm on the outside of the inner beams of the loading platform * Lashing rings with retaining spring every approx. 1,200 - 1,300 mm on the outside of the outer beams of the loading platform (LC 10,000 daN) on the top chord of the outer beams * Cutouts above the lashing rings * 1 hanging lashing ring each left and right on the outer rear crossmember (LC 10,000 daN) on the outer beams of the loading platform * Preparation for removable loading floor * Mounting strip at the front of the rear chassis to the low bed for loose approach ramps * Chassis with chamfered corners at the rear * Mounting strip for loose aluminum approach ramps at the end traverse of the vehicle * Remote steering from front and rear operable via wired remote control with push buttons, axle tracking control, without installation on the tractor unit * Mechanical bolt-lug coupling from the low bed to the chassis, for changing the loading platform or installing extension beams, with electro-pneumatic-hydraulic couplings * Round NATO socket on the front connection strip (Maeler & Kaege VG 96 917) * 2 axle load gauges mounted on the left side Including special accessories: * On the gooseneck: 1 pair of plug-in aluminum side walls, approx. 400 mm high, anodized

Condition: new, maximum load weight: 36,245 kg, overall weight: 45,000 kg, axle configuration: 3 axles, loading space length: 13,500 mm, total width: 2,540 mm, Equipment: ABS, You can find our complete inventory of immediately and short-term available vehicles on our website. Excerpt from the equipment list. Full equipment details available upon request. Load area: * Load platform made of hardwood flooring with rear chamfer approx. 1,000 mm x 8° * 2 pairs of lashing rings (LC 5,000 daN) * 1 pair of lashing rings (LC 10,000 daN) * 6 pairs of outward-folding lashing rings (LC 5,000 daN) * 2 pairs of outward-folding lashing rings (LC 10,000 daN) * Recesses in the outer frame of the load area for attaching tension straps (LC 2,000 daN) Landing legs: * JOST mechanical landing legs with 2-speed gearbox for approx. 24 t lifting capacity (approx. 50 t test load) Axles: * BPW axles, air suspension, disc brakes (approx. 377 mm), lifting/lowering function (ET 120) * Axle tools Tires: * Tires 435/50 R 19.5 – make at our discretion * TPMS tire pressure monitoring system according to ECE R 141. Data transfer to the tractor unit is via the standardized EBS interface according to ISO 11992. The tractor unit must be capable of receiving and displaying this data for correct operation Braking system: * Wabco braking system compliant with EU regulations with EBS-E (2S2M) without connecting lines to the tractor unit Steel construction: * Steel construction made from high-strength fine-grained steels, steel grades: S355J2+N/S355MC (yield strength 355 MPa), S690QL/S700MC (yield strength 690 MPa) Electrical system: * Electrical system in accordance with EU regulations, lighting 24 volt ASPÖCK-NORDIK (ASS3) * All LED side marker lamps flash with the indicators * ASPÖCK-UNIBOX at the front connection strip with sockets 24N, 24S & 15-pin. Connections as per ISO. 24N ISO-1185, 24S ISO-3731, 15-pin ISO-12098 Dcodpfxoyvnfae Agrog Painting: * Complete steel structure shot-blasted after welding with automated shot blast system, secondary blasting with corundum for optimal coating adhesion * HRM metalizing of the entire chassis with ZINACOR 850 (85% zinc / 15% aluminum) for optimum corrosion protection * Final coating with two layers of 2K topcoat, solid in RAL 3002 Carmine Red in accordance with the RAL System 841GL * Rear section metalized and painted RAL 9010 (Pure White) * Paint finish tested to ISO 9227-NSS salt spray standard * Cavity sealing with special wax Including the following additional equipment: * Yellow-red air couplings on the galvanized front connection strip * 4 wheel chocks with holders * 2-inch kingpin * Load platform with heavy-duty hardwood floor * 1 spare wheel holder under the platform on the right-hand side in the direction of travel * Galvanized folding supports under the chamfer of the load area * 9 pairs of stake pockets for plug-in stakes, approx. 100 x 50 mm, in the outer frame of the loading platform * One galvanized steel front wall (EN12642-XL), approx. 1,600 mm high * Anti-slip sand coating painted onto the central beam * 1 INOX crosswise tool box under the deck, approx. 1,000 x 400 x 2,500 mm * 6 pairs of WADER container sockets in the platform, for 1x 20' container, 2x 20' containers or 1x 40' container * 3 pairs of transverse stake pocket rails mounted in the load area, for plug-in stakes approx. 100 x 50 mm * Storage for up to 9 pairs of plug-in stakes approx. 100 x 50 mm, bolted inside the front wall * 2 INOX toolboxes under the platform, left and right, approx. 600 x 350 x 600 mm * Holder for aluminum ramps, crosswise under the platform, behind the axles * 1 beacon supplied loose * 2 pairs of ferry rings under t

Condition: new, maximum load weight: 47,300 kg, overall weight: 58,000 kg, axle configuration: > 3 axles, loading space length: 8,600 mm, total width: 2,540 mm, Equipment: ABS, You can find our complete range of vehicles, including those available immediately and at short notice, on our website. Excerpt from the equipment list. Full specifications available on request. Gooseneck: * Gooseneck with beveled front corners (approx. 45°) and rear bevel (approx. 750 mm x 10°) * 3 pairs of lashing rings (LC 5,000 daN) * Hardwood flooring approx. 30 mm thick Loading area: * Extendable loading platform with rear bevel (approx. 1,000 mm x 8°) * 5 pairs of outward-folding lashing rings (LC 5,000 daN) * 3 pairs of outward-folding lashing rings (LC 10,000 daN) * 1 pair of recessed lashing rings at the front of the loading platform (LC 10,000 daN) * Cutouts in the outer frame of the loading area for hooking tensioning straps (LC 2,000 daN) * Hardwood flooring approx. 48 mm thick; over the axles, diamond plate surface Landing legs: * JOST landing legs (mechanical) with 2-speed gearbox, 24t lifting capacity (50t test load) Tyres: * 235/75 R 17.5 3PMSF tyres, brand at our discretion Axles: * BPW axles, two rigid axles, two trailing steering axles, air-suspended, with drum brakes, lifting/lowering function * Steering axles with electromagnetically-activated reverse lock (via reverse gear or manually) * Axle tools Brake system: * WABCO brake system in accordance with EU regulations with EBS-E (4S3M), no connecting lines to the tractor unit Steel structure: * Steel construction from high-strength fine-grained steels * Steel grades: S355J2+N/S355MC (yield 355 MPa) S690QL/S700MC (yield 690 MPa) Electrical system: * Electrical system compliant with EU regulations, lighting 24 Volt ASPÖCK-NORDIK (ASS3) * ASPÖCK-UNIBOX on the front connection bar with 24N, 24S & 15-pin sockets (ISO standard: 24N - ISO 1185, 24S - ISO 3731, 15-pin - ISO 12098) Paintwork: * Premium and long-lasting corrosion protection of the standard shot-blasted welded frame guaranteed by a 2-component (2K) zinc-rich primer * High-quality 2-component (2K) single-color topcoat RAL 3002 Carmine Red * Rear section metallized and painted in RAL 9010 (Pure White) * Rims in silver Accessories: * Spare wheel holder in front of the bulkhead (without spare wheel) * 2 inch kingpin * Galvanized steel front wall approx. 400 mm high * Yellow-red air couplings on the galvanized front connection bar * Receptacle at the rear of the gooseneck for ALU loading ramps * Galvanized drop-down supports under the loading area bevel * Bracket for a revolving beacon at the rear of the trailer * Brackets left and right on the gooseneck and rear plate for warning signs including socket * TPMS tire pressure monitoring system compliant with ECE R 141 * Removable ALU sideboards and rear wall on the gooseneck, approx. 2,440 x 400 mm (L x H); rear galvanized insert posts are removable (body length approx. 2,560 mm) Dcjdpfxoyvnfgo Agrjg * Galvanized toolbox integrated in the beveled gooseneck * 3 pairs of WADER container locks in the loading platform for one 20' (30') or one 40' container * Sliding hook-in rails for ALU loading ramps at the rear of the vehicle * 6 pairs of pockets for plug-in posts, approx. 100 x 50 mm in the outer frame of the loading area * Galvanized extensions, extendable by approx. 230 mm per side * Lift axle on the front axle with TEBS E control based on current axle load and load status * 2 LED reversing lights mounted on the rear plate * 2 pairs of ferry-