Used Faymonville Ilo Semitrailers for sale (202)

Condition: new, maximum load weight: 37,820 kg, overall weight: 48,000 kg, axle configuration: 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our entire vehicle inventory, including immediately and short-term available vehicles, on our website. Excerpt from the equipment. Full equipment details available upon request. Gooseneck: - Gooseneck with beveled front corners approx. 45° and rear chamfer approx. 750 mm x 10° - 3 pairs of lashing rings (LC 5,000 daN) - Hardwood floor covering approx. 30 mm thick Loading area: - 1 pair of fixed wheel recesses in front of the axles, approx. 2,610 x 970 x 400 mm (L x W x D) - Wheel recesses with square climbing slats approx. 15 x 15 mm and widenings in the lower section - Between the 1st and 2nd axles, a pair of fixed wheel recesses, approx. 1,610 x 700 x 400 mm (L x W x D) - Incl. 3-piece removable galvanized covers over the wheel recesses (W approx. 670 mm) – max. point load approx. 5 t/each - Recess in the chamfer and extending into the loading area for receiving the excavator bucket arm (approx. 2,900 x 750 x 210/290 mm (L x W x H)) - 1 pair of lashing rings, horizontal, at the front of the loading area (LC 10,000 daN) - 5 pairs of flip-out lashing rings (LC 5,000 daN) - 3 pairs of flip-out lashing rings (LC 10,000 daN) - 2 pairs of lashing rings in the excavator arm recess (LC 5,000 daN) Gjdpfow Tpqwsx Afnsbk - Cut-outs in the outer frame of the loading area for securing straps (LC 2,000 daN) One-piece Steel Ramps: - One pair of galvanized one-piece steel ramps, approx. 3,000 x 800 mm, with approx. 48 mm thick hardwood covering - Ramp with hydraulic lifting mechanism, hydraulically adjustable - Maximum load per pair: 40,000 kg - In accordance with Regulation 1230/2012/EU, ramps with a length less than 300 mm do not count towards the vehicle length in the driving position Landing gears: - JOST landing gears (mechanical) with 2-speed gearbox for approx. 24 t lifting capacity (approx. 50 t test load) Axles: - BPW axles and suspension, 2 fixed axles, 1 trailing steering axle - Technical axle load: 12,000 kg each - Electromagnetic reverse lock, activated via reverse gear and manually - Air suspension with lift and lower valve - Axle tool kit Tyres: - Tyres 235/75 R 17.5 3PMSF – manufacturer of our choice - TPMS tyre pressure monitoring system in accordance with ECE R 141. The data transmission to the truck is via standardized EBS interface according to ISO 11992. For correct display, the truck must be able to transmit and display this data Braking system: - WABCO braking system in accordance with EU regulations with EBS-E (2S2M) without connecting lines to the tractor unit Steel construction: - Steel structure made of high-tensile fine-grain steels - Steel grades: S355J2+N/S355MC (yield strength 355 MPa), S690QL/S700MC (yield strength 690 MPa) Electrical system: - Electrical system according to EU regulations - Lighting 24 volts ASPÖCK-NORDIK (ASS3) - All LED side marker lights flash with the indicator - ASPÖCK-UNIBOX at the front connection strip with 24N, 24S & 15-pin sockets as per ISO. 24N ISO-1185, 24S ISO-3731, 15-pin ISO-12098 Paintwork: - Complete steel structure automatically shot-blasted with blasting wheel machine after welding - Second shot-blasting using corundum for optimal coating adhesion - HRM metallization of the entire vehicle chassis with ZINACOR 850 (85% zinc/15% aluminum) to ensure maximum corrosion protection - Final painting with 2 coats of two-component topcoat, single color in RAL 3002 Carmine Red, according to the RAL system 841GL - Rims in silver - Rear section metallized and in RAL 9010 (continuation see ori

Condition: new, total length: 19,000 mm, total width: 600 mm, total height: 450 mm, Year of construction: 2022, Colour: Red Loading capacity: 430,000 kg Expandable Manufacturer: Faymonville Model: G-Module Vesseldeck Year: 2022 Compatible with Goldhofer THP SL Coupling Heads G-Module SL lowbed coupling head Hydraulically extendable Base width: 3,000 mm Hydraulically extendable to 4,700 mm Beam height: 450 mm Coupling length: 1,200 mm Weight: 4,500 kg 4 pairs of lashing rings (LC 16,000 daN) 2 alignment pins Control panel for hydraulic adjustments Colour: RAL 3002 Gjdouu Hixopfx Afnsbk Telescopic Beams 1 pair of telescopic beams Length: 8,000 mm + 5,000 mm Total length: 13,000 mm Construction height: 450 mm Beam width: 450/600 mm Weight: 9,600 kg Lashing rings every 1,000 mm LC 10,000 daN 430 MTO Compression connector at front and rear Colour: RAL 3002 Extension Beams 1 pair of extension beams Coupling length: 6,000 mm Construction height: 450 mm Beam width: 450/600 mm Weight: 4,300 kg Lashing rings every 1,000 mm LC 10,000 daN 560 MTO Compression connector at front and rear Colour: RAL 3002 Coupling Pin 1 hydraulic coupling pin for G-Module 1 connecting lines kit for G-Module coupling pin = Further information = Year of manufacture: 2022 Unladen weight: 18,500 kg General condition: Very good Technical condition: Very good Visual condition: Very good Price: On request Please contact Stefan Schaapveld for further information.

Condition: used, color: green, Year of construction: 2018, Faymonville F-S42-2ACB. Year: 2018. 12-ton Pendel-X axles. Max gross weight: 49,000 kg. Kingpin load: 25,000 kg. Hydraulic detachable gooseneck. Hydraulics operate on NATO connection from a truck. EBS, ABS, ALB. Spare wheel. Hydraulic suspension. Remote control via cable. Aluminium side boards and toolbox on neck. Extendable by 5.5 meters. Widened sections: 2 x 25 cm. Excavator trough: 2750 x 600 mm. Zinc-coated. Dimensions: Neck: L: 3650 mm W: 2500 mm H: 1550 mm Kingpin height: 1250 mm Gbedpfx Asxwbuusfnek Deck: L: 8000 mm W: 2550 mm H: approx. 350 mm Deck thickness: 220 mm Rear of trailer: L: 2750 mm W: 2550 mm H: 1000 mm Tyres: 245/70R17.5, 80% tread remaining German trailer! ID No: 465. The General Terms and Conditions of Heinhuis apply to all advertisements, offers, and quotations by Heinhuis, all agreements entered into by Heinhuis, and the negotiations preceding them. By responding in any way, you accept the applicability of the General Terms and Conditions of Heinhuis and declare that you are aware of these Terms and Conditions. Our prices are net export prices. = Further information = Year of manufacture: 2018 Gross vehicle weight: 49,000 kg Extendable frame: Yes Price: On request = Company information = For more information: WhatsApp:

Condition: used, color: blue, Year of construction: 2016, Faymonville F-S43-1ABA. Year: 2016. 10 tons SAF axles. Max weight: 42,000 kg. Kingpin load: 18,000 kg. Power steering 3 steering axles. Air suspension. Wink. EBS ABS ALB. Hydraulic works on Duplo electricity. Hydraulic bridge from floor to neck. Length: 3000mm. Central greasing system. 2 point hydraulic outriggers on the back. 2 way hydraulic ramps: - hydraulic from left to right. - length: 2800 + 1700 mm. Dimensions: Neck: L: 3800mm. W: 2480mm. H: 1400mm. Kingpin load: 1150 mm. Floor: L: 9600mm. W: 2550mm. H: 900mm. Tires: 235/75R17.5 70%. German Trailer! ID NO: 449. The General Terms and Conditions of Heinhuis are applicable to all adverts, offers and quotations by Heinhuis, all agreements entered into by Heinhuis and the negotiations preceding them. By any form of response you accept the applicability of the General Terms and Conditions of Heinhuis and you declare that you have taken note of these General Terms and Conditions. Our prices are export net prices. = Further information = Year of construction: 2016 GVWR: 42,000 kg Gbedpfx Afoxvzm Usnok = Company information = For more information: WhatsApp:

Condition: used, empty load weight: 20,320 kg, maximum load weight: 46,180 kg, overall weight: 66,500 kg, axle configuration: > 3 axles, first registration: 01/2004, tire size: -, Year of construction: 2004, Ref: 2220 Gbjdjwcrzrepfx Afnjk Extra low-bed trailer with 3 rear axles + 1 front axle (dolly). Maximum authorized weight: 66 T. Trailer with detachable gooseneck. Extendable trailer (5 m). Trailer with 3 forced steering axles (and manual remote control). Trailer can be driven with or without a dolly. Total trailer length: 16.43 m + 5 m (extendable). Tare weight: 20,320 kg + 2,520 kg for a dolly. Gooseneck: L= 4.43 m. Extra low-bed: L= 7.5 m + 5 m (extendable). Height: 0.5 m. Trailer width: 2.74 m. Dock above rear axles: L= 4.5 m. H= 1.05 m. Dipper pit for excavator dippersticks. Rear ramps. Hydraulic (removable) and hydraulic ramp movement Tow tires: 285/70R19.5 Dolly tires: 235/75R17.5 Serial number: YA9TL366B04113968+122B4113969

Condition: new, maximum load weight: 40,790 kg, overall weight: 59,000 kg, axle configuration: 3 axles, total width: 2,750 mm, Equipment: ABS, You can find our complete vehicle inventory with immediately and soon-available vehicles on our website. Excerpt from the equipment list. Full specifications available on request. Gooseneck: - Gooseneck in SNT design to optimize loading platform length, approx. 3,700 mm long - Gooseneck hydraulically liftable/lowerable and detachable - For tractor units: 6x4 or 8x4 Low bed: - Low bed with external beams, extendable design, SUPER LOW version, approx. 7,550 mm long - Low bed with fixed hardwood flooring, approx. 40 mm thick, and mechanical locking - Supply lines are protected within the extendable beams and automatically adjust to the current bed length - 7 pairs of lashing rings, foldable outward (approx. LC 10,000 daN) - 6 pairs of threaded blocks on the inner beam for mounting bolt-on RUD rings Rear running gear: - Rear running gear with closed outer frame, checker plate floor and continuous prism excavator trough, approx. 1,450/900 x 505 mm, open at the rear - 2 pairs of lashing rings, foldable outward (approx. LC 10,000 daN) - 1 pair of flat lashing rings in the trough (approx. LC 10,000 daN) - 2 pairs of flat lashing rings in the trough (approx. LC 16,000 daN) - 2 pairs of stake pockets for plug-in stakes approx. 100 x 50 mm in the outer frame PENDLE-AXLE: - PENDLE-AXLE, all axles hydro-mechanically forced-steered - Hose rupture valve on axle compensation cylinder with automatic reset function - Hydraulic cylinders with shut-off valves and lock pins to secure in raised position - Final coating of axles with 2 coats of 2-component paint, single color in grey 34-0260 - Technical axle load: 12,000 kg each - Hydraulic axle compensation - Axle tools Tyres: - Tyres 245/70 R 17.5 3PMSF – brand of our choice. Load index (146/146F) Braking system: - Braking system according to EU regulations with EBS-E (2S2M) without interconnected lines to the tractor unit Electrical system: - Electrical system according to EU regulations - Lighting 24 Volt ASPÖCK-NORDIK (ASS3) - ASPÖCK-UNIBOX at the front connection bar with 24N, 24S & 15 pin sockets. Connections according to ISO: 24N ISO-1185, 24S ISO-3731, 15 pin ISO-12098 Steel structure: - Steel structure made of high-strength fine-grained steels - Steel grades: S355J2+N/S355MC (yield strength 355 MPa), S690QL/S700MC (yield strength 690 MPa) Painting: - Entire steel structure automatically shot-blasted with a wheel blasting machine after welding - Second abrasive blasting with corundum for optimal adhesion of the coating system Gjdpfx Asw Tprbofnebk - Final coating with 2 layers of 2K topcoat, single color in RAL 3002 carmine red according to RAL system 841GL - Rear section metallized and painted in RAL 9010 (pure white) - Rims in silver-grey - No metallic paintwork possible - Paint structure tested in salt spray test according to ISO 9227-NSS - Sealing of cavities with special wax Accessories included: - Preparation for installation of bolt-on container positioning devices for 1x 20' or 1x 40' container on the outer beams - Without container locks - 3.5-inch king pin - One galvanized steel front wall, approx. 400 mm high - One spare wheel carrier in front of the front wall - At the galvanized front connection bar, yellow-red air couplings - Remote steering from front and rear via cable remote control with push buttons, with single-track monitoring of axles (without installation in the tractor unit) - Electro-hydraulic unit - On the gooseneck, plug-in aluminium side and rear walls, approx. 2,000 x 400 mm (L x H)

Condition: new, maximum load weight: 25,645 kg, overall weight: 38,000 kg, axle configuration: 2 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete stock of immediately and soon-to-be available vehicles on our website. Excerpt from equipment specification. Complete specification available on request. Load area: - Low-bed design with central beam, extendable version, approx. 6,750 mm in length - 5 pairs of fold-out external lashing rings (LC 5,000 daN) - 1 pair of fold-out external lashing rings (LC 10,000 daN) - 1 pair of flat-mounted lashing rings at the rear of the loading platform (LC 10,000 daN) Gbsdpfx Afsxf Silsnok Gooseneck: - Hydraulic lifting/lowering gooseneck, detachable Rear chassis: - Short rear chassis with closed outer frame and checker plate covering - Chassis with excavator trough, closed in the rear half for housing the air tanks - 2 pairs of fold-out external lashing rings (LC 5,000 daN) - 1 pair of fold-out external lashing rings (LC 10,000 daN) - 1 pair of flat-mounted lashing rings at the rear of the chassis (LC 10,000 daN) Axles: - BPW axles, hydro-mechanically forced steering - Air suspension with raise/lower control valve Tyres: - Tyres 245/70 R 17.5, 3PMSF - TPMS: Tyre Pressure Monitoring System according to ECE R 141 Brake system: - Wabco braking system in accordance with EU regulations with EBS-E (2S2M) Paintwork: - High-quality single-tone 2-component (2K) top coat in RAL 3000 Flame Red Including the following additional equipment: - 2 kingpins - Galvanised steel front wall, approx. 400 mm high - Remote steering from front and rear, operated by cable remote control with push buttons, including single tracking control for the axles (no installation in the tractor unit) - Electro-hydraulic unit - Axle load gauge including load diagram - On the gooseneck, removable aluminium side walls and rear wall, approx. 2,440 x 400 mm (L x H). Rear galvanised stake pockets are removable. (Body length approx. 2,560 mm) - Separate air connection with air gun on the gooseneck - 2 work lights with switch on the trailer, mounted on the left and right of the gooseneck platform - 1 INOX toolbox, approx. 1,350 x 400 x 400 mm, on the gooseneck - 6 pairs of stake pockets for insertable posts approx. 100 x 50 mm in the outer frame of the load area, 2 pairs in the chassis outer frame - Galvanised, extendable width extensions approx. 230 mm per side - Hydraulic connections from gooseneck to low bed with multi-coupling (instead of screw couplings). No seal guarantee included. - Central lubrication system with 2 BEKAMAX (Pico) pumps, standard NLGI-2 grease, with removable protection around the pump - 2 pairs of WADER container locks on the loading area, for 1x20' container - 1 removable galvanised intermediate table with 1 pair of WADER container locks - 1 pair of steel ramps for bridging the low bed’s hook mountings - Anti-slip sand-coated layer painted on the load area - HRM Metallisation (High Resistance Metallisation)

Condition: new, maximum load weight: 25,300 kg, overall weight: 38,000 kg, axle configuration: 2 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory, including vehicles available immediately or at short notice, on our website. Excerpt from the equipment details. Full specifications available upon request. Neck (Gooseneck) * Gooseneck in SNT design to optimize loading platform length * Approx. 3,750 mm long, hydraulically liftable/lowerable and detachable * Technical fifth wheel load: 25,000 kg For tractors: 4x2 and 6x2 Kessel Bridge (Tiefbett section) * Low bed designed as extendable Kessel bridge in SUPER LOW design * Approx. 6,850 mm length * With mechanical locking * Service lines routed protected inside the extendable beams, automatically adjusting to match the low bed’s length Rear Chassis * Short version with closed outer frame and checker plate cover * Chassis with excavator trough, closed at the rear half to accommodate air tanks Axles * BPW axles and suspension, all axles hydro-mechanically forced steered * Technical axle load: 12,000 kg per axle * Air suspension with lifting and lowering valve Tires * GOODYEAR KMAX T 3PMSF (M+S) 245/70 R 17.5 twin tires. Load index 143/141J (146/146F) Brake system * Brand: WABCO, EBS-E according to EU regulations, without connection cable to the tractor unit Paintwork * 6-Coat final treatment * All-steel construction shot-blasted after welding * 1 layer of zinc-based primer * 1 layer of adhesion primer. Final coating with 2 coats of 2-component acrylic paint in a single color, followed by cavity sealing with special wax Trailer color * RAL 3002 Carmine Red * Rim color: Silver grey * Drop side color: Natural aluminum Accessories included * Removable steel front wall, approx. 400 mm high * 3 kW electro-hydraulic unit for hydraulic operations (except for hydraulic winches). Without supply connection installed on tractor unit * Spare wheel carrier in front of the gooseneck front wall * Side beams of the gooseneck with fixing holes for bolted lashing rings; first hole approx. 200 mm from the front, then at approx. every 400 mm * 2 pairs of screw-in lashing rings included (LC 5,000 daN) Gbodsv Sw E Ajpfx Afnsk * 1 lashing ring each left and right on the rear taper of the gooseneck (LC 6,000 daN) * 2" king pin * Hydraulic cross member for supporting the gooseneck on the tractor unit or a dolly * Air connection with air gun at the gooseneck * 1 pair of steel ramps with climbing strips and securing pins to bridge the mountings of the low bed * 1 lashing ring each left and right on the front cross member (LC 10,000 daN) * Outer side beams of the loading area prepared for removable loading floor * Lashing rings with retaining spring at approx. every 1,200–1,300 mm on the inside carrier’s exterior of the loading area * Lashing rings with retaining spring at approx. every 1,200–1,300 mm on the outer carrier’s exterior of the loading area (LC 10,000 daN) * Cut-outs above the lashing rings in the outer carrier’s upper flange * Mechanical pin-tab coupling from low bed to rear chassis, for swapping the loading floor or installing extension beams, with electro-pneumatic-hydraulic couplings * The outer carriers of the low bed coated with anti-slip sand finish for slip resistance * 2nd ride height for high ride position, max. ± 50 mm from normal ride position, without installation of controls from the tractor unit * 1 pair lashing rings with retaining spring at the transition from the low bed to the excavator trough (LC 10,000 daN) * Front and rear tapers

Condition: new, maximum load weight: 36,500 kg, overall weight: 48,000 kg, axle configuration: 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete inventory of immediately and short-term available vehicles on our website. Excerpt from the equipment features. Full equipment list available upon request. - Gooseneck, approx. 4,100 mm in length with central beam - Load platform with double-extendable design, length approx. 9,400 mm - BPW axles and suspension - All axles hydromechanically forced-steered - Technical axle load: 12,000 kg - Air suspension with raise and lower valve - Twin tires 235/75 R 17.5 3PMSF - WABCO braking system, EBS-E - 3 kW electro-hydraulic unit for hydraulic operations. Without installation of supply connections on the tractor unit - 4 pairs of stake pockets integrated in the outer frame of the gooseneck, suitable for insertable stakes approx. 100 x 50 mm Godpfx Aswvzg Refnebk - 2-inch king pin - 8 pairs of stake pockets integrated in the outer frame of the loading area, suitable for insertable stakes approx. 100 x 50 mm - 1 lockable INOX toolbox, approx. 1,250 x 500 x 550 mm (L x W x H), mounted under the loading platform on the left-hand side in direction of travel - Remote steering control from front and rear using cable remote with push buttons, with axle tracking control, without installation in the tractor unit - 2 axle load gauges mounted on the left side - Steel front wall, approx. 1,600 mm high - 3 transverse rows of stake pockets mounted in the floor of the loading area for insertable stakes approx. 100 x 50 mm - 1 transverse row of stake pockets mounted in the floor of the gooseneck for insertable stakes approx. 100 x 50 mm - 1 additional lockable INOX toolbox, mounted under the loading area - WADER container pockets in the loading area for transporting: 2x 20' containers or 1x 40' container - Central automatic lubrication system with 2 pumps, BEKAMAX brand - Complete HRM Metalization (High Resistance Metallisation)

Condition: new, maximum load weight: 67,200 kg, overall weight: 85,000 kg, axle configuration: > 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory, including immediately and short-term available vehicles, on our website. Excerpts from the equipment. Full specifications available upon request. GOOSENECK * Gooseneck in SNT design to optimize load floor length, approx. 3,700 mm long, with rear bevel approx. 1,000 mm x 10° * For tractors: 6 x 2, 6 x 4, and short 8 x 4 * Detachable steel front wall, approx. 400 mm high * 3 kW electro-hydraulic power unit for controlling hydraulic functions, except for hydraulic winches Gbjdpfx Afsrgzv Nsnok * Outer beams of the gooseneck with mounting holes for bolt-on lashing rings * 2 pairs of screw-in lashing rings included (LC 5,000 daN) * 1 pair of flat lashing rings at the rear of the gooseneck (LC 10,000 daN) * 1 pair of plug-in aluminum side boards, approx. 400 mm high, anodized * 1 plug-in aluminum rear board, approx. 400 mm high, anodized * Approx. 40 mm thick hardwood flooring above gooseneck, checker plate flooring above kingpin * 3.5 inch kingpin * Gooseneck guide plate for the fifth wheel plate, approx. 500 mm wide * Round NATO socket at the front connection strip (Maeler & Kaege VG 96 917) * In addition to the electro-hydraulic unit, a truck hydraulic connection with flow regulator, including bracket for hanging supply lines (Faymonville couplers) * 2 pairs of stake pockets recessed in the gooseneck, for plug-in stakes approx. 100 x 50 mm LOAD FLOOR * Extendable load floor, approx. 11,000 mm long, with rear bevel approx. 500 mm x 10° * Pneumatic locking with conical locking bolts and reinforced locking positions; supply lines are protected inside the extendable beams and automatically adjust to the respective deck length * BPW axles and suspension, 1st axle steered, 2nd axle fixed, all other axles hydro-mechanically forced steered * 1st axle with electro-magnetic reverse lock via reverse gear and manual activation * Axle load capacity: 12,000 kg each * Air suspension with lift and lower valve * 235/75 R 17.5 3PMSF twin tires * Mechanical landing gears with 2-speed gearbox and crank. JOST Modul B – static test load = approx. 50,000 kg * Continuous and, between axles, interrupted approx. 50 mm thick hardwood floor on load deck (increases coefficient of friction) * Slotted holes for attachable and repositionable bridging elements: – at the fixed part behind the gooseneck – on the front of the load floor * 1 sliding intermediate table, approx. 500 mm wide, for the sliding tube with large cross-section, checker plate flooring, front and rear with slotted holes for attachable and repositionable bridging elements * 1 pair of recessed flat lashing rings in the front fixed part of the load floor (LC 10,000 daN) * 9 pairs of recessed lashing rings, foldable outward, in the load floor perimeter frame (LC 10,000 daN) * 1 pair of mechanical rear supports * Remote steering from front and rear via cable remote control, with axle tracking control, no installation required in the tractor * 1st axle with automatic lift axle function and start-up assist according to EU Regulation 2021/535 * Under the gooseneck and at the rear cross member, left and right, a 7-pin socket each with holder for warning signs * Factory-applied sand coating on the perimeter frame of the load floor as well as the checker plates and the transition area between load decks

Condition: new, maximum load weight: 73,540 kg, overall weight: 102,000 kg, axle configuration: > 3 axles, Equipment: ABS, You can find our complete inventory of vehicles, including units available immediately and at short notice, on our website. Overview of equipment. Full equipment list available on request. Neck (gooseneck): * Hydraulically liftable/lowerable and removable gooseneck, length approx. 3,650 mm Gsdpfoxbmpljx Afnjbk * 2 pairs of fold-out lashing rings (LC 5,000 daN) * 2 pairs of lashing rings on the gooseneck (LC 10,600 daN) * 1 pair of lashing rings in the center section of the gooseneck (LC 10,600 daN) * For 6x4 or 8x4 2-axle tractor units Compact front bogie: * Hook pick-up front and rear, length: approx. 2,200 mm * Bogie width: approx. 2,850 mm Excavator deck: Telescopic excavator deck with drive-over deck hooks at the front and bolt-lug coupling at the rear * Basic width: approx. 2,850 mm * Length: approx. 6,650 mm * Beam height: approx. 400 mm * Beam width: approx. 1,350 mm * Loading height approx. 550 mm with ground clearance of approx. 150 mm 4-axle rear bogie: * Mechanical bolt-lug coupling at the front for mounting a lowbed * Rear crossmember bogie width: approx. 2,850 mm * Bogie length: approx. 5,480 mm Pendulum axles, all axles hydro-mechanically steered * Technical axle load: 14,640 kg each (62 km/h) * Hydraulic axle compensation Tyres: * Front bogie: * 8 x manufacturer’s choice (M+S) 285/70 R19.5 * Rear bogie tyres: * 16 x manufacturer’s choice (M+S) 285/70 R19.5 * Load index 150/148J Paintwork: * Complete steel construction is automatically blasted with a blasting wheel system after welding. Second blasting with corundum for optimal adhesion of the coating system * Full chassis HRM-metallized with ZINACOR 850 (85% zinc/15% aluminum) for maximum corrosion protection * Final painting with two coats of 2K topcoat, single-color in RAL 3002 carmine red, according to RAL system 841GL Including the following accessories: * Steel front wall, approx. 400 mm high * Plug-in ALU sidewalls and rear wall, approx. 400 mm high, anodized version, fitted on the gooseneck * 3.5 inch kingpin * Truck hydraulic connection with flow control (20 l/min) * Support gallows for supply lines, tractor unit tank must be at least 80 l * with MAX Trailer couplings, otherwise customer to supply coupling parts ex works * BEKA-MAX central lubrication for one gooseneck with standard grease NLGI-2 * Tool kit Art No. 612452 * Multi-coupling hydraulic connections on the gooseneck * Front bogie with separate air connection for air screwdriver * BEKA-MAX central lubrication for one 2-axle bogie with standard grease NLGI-2 * One 7-pin socket left and right rear on the front bogie for warning signs * Screw-in facility (ø approx. 40 mm) every approx. 500 mm on the outside of the upper flange of the outer tube of the excavator deck for bolt-on rings (LC 16,000 daN) * Foldable width extensions with steel covers, adjustable in width from approx. 2,850 mm to approx. 3,250 mm * BEKA-MAX central lubrication for one 4-axle bogie with standard grease NLGI-2 * At the rear bogie, a socket for the cable remote control of the steering * Rear bogie with trough * Two INOX toolboxes, approx. 855 x 340 x 390 mm, mounted left and right on the gooseneck * 1-cylinder Hatz diesel engine (Silent Pack) with electric starter and starter battery * Radio remote control: * Operation of the powerpack, start/stop of the diesel engine * Control of the steering, in addition to the cable remote control * One LED work light each left and right at the end plate of the gooseneck with...

Condition: new, maximum load weight: 91,640 kg, overall weight: 126,000 kg, axle configuration: > 3 axles, total width: 2,850 mm, Equipment: ABS, You can find our complete vehicle inventory, including immediately and short-term available vehicles, on our website. Excerpt from the equipment features. Full specification available upon request. Gooseneck Gsdeuvbdtopfx Afnjbk * Hydraulically liftable/lowerable and detachable gooseneck. Length approx. 3,650 mm. Suitable for tractor units: 6 x 4 or 8 x 4 3-Axle Compact Front Bogie * Hook couplings front and rear, length: approx. 3,560 mm * Chassis width: approx. 2,850 mm Excavator Deck * Telescopic excavator deck BB-A with drive-over deck hooks at the front and a bolt coupling at the rear * Base width: approx. 2,850 mm, Length: approx. 7,150 mm, Main beam height: approx. 430 mm, Main beam width: approx. 1,350 mm * Loading height approx. 580 mm with ground clearance approx. 150 mm 5-Axle Rear Bogie * Mechanical bolt coupling for front connection of a low-bed, rear end traverse * Chassis width: approx. 2,850 mm * Chassis length: approx. 6,840 mm * 3-axle pendulum axle Front Bogie * PENDULUM AXLE, all axles hydro-mechanically forced-steered * Hose rupture valve on axle compensation cylinder with automatic RESET function * Hydraulic cylinders with shut-off valves and stopper pins for securing in raised position * Axles finished with 2 layers of MB7350 Novagrau single-colour 2-component paint * Technical axle load: 14,640 kg per axle (62 km/h) * Hydraulic axle compensation * Front bogie tyres: 12 x Manufacturer’s choice (M+S) 285/70 R19.5, load index 150/148J, pendulum axle 5-Axle Rear Bogie * PENDULUM AXLE, all axles hydro-mechanically forced-steered * Hose rupture valve on axle compensation cylinder with automatic RESET function * Hydraulic cylinders with shut-off valves and stopper pins for securing in raised position * Axles finished with 2 layers of MB7350 Novagrau single-colour 2-component paint * Technical axle load: 14,640 kg per axle (62 km/h) * Hydraulic axle compensation * Rear bogie tyres: 20 x Manufacturer’s choice (M+S) 285/70 R19.5, load index 150/148J Paintwork * HRM metallization of the entire vehicle chassis using ZINACOR 850 (85% zinc/15% aluminium) to ensure the best possible corrosion protection * Final coat with two layers of 2K topcoat, single-colour in RAL 3002 Carmine Red, according to the RAL System 841GL. Rims in silver grey Incl. Accessories * Steel front wall, approx. 400 mm high * Detachable ALU side walls and rear wall approx. 400 mm high in anodized finish, mountable on the gooseneck * 3.5" kingpin * BEKA-MAX central lubrication system for one gooseneck * Multi-coupling hydraulic connections on the gooseneck * BEKA-MAX central lubrication system for one 3-axle bogie * One 7-pin socket left and right rear on the front bogie for warning signs * Screw-in option (ø approx. 40 mm) every approx. 500 mm on the outside of the upper flange of the external tube of the excavator deck for lashing rings (LC 16,000 daN) * Folding extensions with steel mattress, width adjustable from approx. 2,850 mm to approx. 3,250 mm * Steel mattresses can be positioned in 2 ways to achieve a lowered loading platform. Load capacity depends on extension, refer to the respective load chart * Steel mattresses with rubber flooring approx. 12 mm thick * One 7-pin socket left and right, front and rear of the rear bogie for warning signs * BEKA-MAX central lubrication system for one 5-axle bogie * Socket on the rear bogie for cable remote control of rear steering * Rear bogie with trough * Two INOX toolboxes, approx. 855 x 340 x 390 mm, mounted on the goos

Condition: used, maximum load weight: 37,535 kg, overall weight: 48,000 kg, axle configuration: 3 axles, first registration: 08/2024, next inspection (TÜV): 08/2026, total width: 2,540 mm, Equipment: ABS, You can find our entire vehicle inventory, including immediately and soon-available vehicles, on our website. The following is an excerpt from the equipment specification. Full equipment details available on request. Loading Platform: * Extendable loading platform with pneumatically operated locking mechanism * 7 pairs of fold-out lashing rings (LC 5,000 daN) * 3 pairs of fold-out lashing rings (LC 10,000 daN) * Cut-outs in the outer frame of the loading platform for attaching tension straps (LC 2,000 daN) Landing Legs: * JOST landing legs (mechanical) with 2-speed gearbox for approx. 24 t lifting capacity (approx. 50 t test load) Axles: Gbedsxgk U Nepfx Afnek * BPW axles, air-suspended, with disc brakes (approx. 430 mm), fitted with lift/lower function. Technical axle load: 10,000 kg each (ET0) * Self-steering axle with electromagnetic reverse lock, activated via reverse gear or manually * Axle tool Tyres: * Tyres 385/65 R 22.5 Brake System: * Brake system compliant with EU regulations with EBS-E (2S2M), without connecting lines to tractor unit Steel Construction: * Steel construction made of high-strength fine-grained steels * Steel grades: S355J2+N/S355MC (yield strength 355 MPa), S690QL/S700MC (yield strength 690 MPa) Paintwork: * Premium and durable corrosion protection of the standard shot-blasted welded frame by a two-component (2K) zinc dust primer * High-quality single-color topcoat (2K) in RAL 3002 carmine red * Rims in silver * Rear section metallised and painted in RAL 9010 (pure white) Including the following additional equipment: * Yellow-red air couplings on galvanised front connector bar * 4 wheel chocks with holders * 2" king pin * Yellow reflective tape compliant with EU-standard on sides, extension and trailer rear * European reflector boards (red-yellow) on rear of trailer * Loading platform with approx. 30 mm thick wooden floor encased in Omega profiles * 10 pairs of stake pockets for insertable stanchions approx. 100 x 50 mm in the outer frame of the loading platform * Storage for up to 9 pairs of insertable stanchions approx. 100 x 50 mm bolted to the inside of the front wall * 1 spare wheel holder under the loading platform on the left in the driving direction, without spare wheel * One mudflap at the rear of the trailer * Manual and documentation on USB stick * Bracket for rotating beacon at the rear of the trailer * On gooseneck and rear panel, left and right, one holder each for warning signs, including socket * Speed stickers 80 km/h, rear and both sides * Load gauge for axle load determination including load chart * Galvanised steel front wall (EN12642-XL), approx. 1,600 mm high * 6 pairs of WADER container pockets on loading platform, for 1x 20' container, 2x 20' containers or 1x 40' container flush with the rear * INOX toolbox, approx. 600 x 350 x 600 mm, under the platform on the left in the driving direction * 4 pairs of longitudinal stake pocket rails for 80 x 50 mm insertable stanchions mounted on the loading platform * Lift axle on the front axle with control via TEBS E depending on current axle load and loading condition * 2 LED reversing lights mounted on rear panel * HRM metallisation (High Resistance Metallisation)

Condition: new, maximum load weight: 38,140 kg, overall weight: 48,000 kg, axle configuration: 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory, including vehicles available immediately and at short notice, on our website. Excerpt from equipment. Full equipment details available on request. Gooseneck: - Gooseneck with front corners chamfered approx. 45° and rear bevel approx. 750 mm x 10° - 3 pairs of lashing rings (LC 5,000 daN) - Hardwood flooring, approx. 30 mm thick Loading area: - Telescopic loading area with rear incline approx. 1,000 mm x 8° - Between 1st and 2nd axle: one pair of fixed wheel recesses, approx. 1,610 x 970 x 400 mm (L x W x D) - Incl. 3-piece removable galvanized cover over wheel recesses (width approx. 670 mm – max. point load 5 t / pc.) - 1 pair of flat lashing rings at the front of the loading area (LC 10,000 daN) - 4 pairs of outward folding lashing rings (LC 5,000 daN) - 3 pairs of outward folding lashing rings (LC 10,000 daN) - Cutouts in the outer frame for attaching tie-down straps (LC 2,000 daN) Landing legs: - JOST landing legs (manual) with 2-speed gearbox for 24 t lifting capacity (50 t test load) Tyres: - Tyres 235/75 R17.5 3PMSF, make at our discretion - TPMS tyre pressure monitoring system in accordance with ECE R 141 - Data transfer to the towing vehicle via standardised EBS interface as per ISO 11992 - For correct display, the towing vehicle must be able to receive and display this data Axles: - BPW axles and suspension, 2 axles rigid, 3rd axle self-steering - Technical axle load: 12,000 kg - Electromagnetic reverse lockout activated automatically when reversing and manually - Air suspension with lifting and lowering valve. Axle tools Braking system: - WABCO braking system according to EU regulations with EBS-E (2S2M) without piping to the tractor unit Electrical system: - Electrical system per EU regulations - LED lighting 24 Volt ASPÖCK-NORDIK (ASS3) - All LED side marker lights flash with the indicator - ASPÖCK-UNIBOX at front connection strip with 24N, 24S & 15-pin sockets, according to ISO; 24N ISO-1185, 24S ISO-3731, 15-pin ISO-12098 Steel construction: - Steel structure made of high-strength fine-grained steels - Steel qualities: S355J2+N/S355MC (yield strength 355 MPa), S690QL/S700MC (yield strength 690 MPa) Paintwork: - Complete steel structure automatically shot-blasted after welding in a wheel-blasting system - Second shot-blasting with corundum for optimum coating adhesion - HRM metallization of entire chassis with ZINACOR 850 (85% zinc/15% aluminium) for maximum corrosion protection - Final painting with 2 layers of 2K topcoat, single-colour in RAL 3002 Carmine Red, rear section metallized and painted in RAL 9010 Pure White - Metallic finish not available - Paint structure tested in salt spray test according to ISO 9227-NSS - Internal cavities sealed with special wax Including the following accessories: - On the gooseneck and rear, left and right, one holder for warning signs each, including socket - Spare wheel holder in front of the front wall (without spare wheel) - 2-inch king pin - Galvanized steel front wall, approx. 400 mm high Gbjdpow Tpq Dofx Afnjk - Yellow-red air couplings on the galvanized front connection bar - Galvanized folding supports under the inclination at the rear of the loading area - A hardwood crash protection strip at the rear wall from gooseneck to the loading area - 1 pair of recessed lashing rings along the central beam at the rear inclination (LC 10,000 daN) - Aluminium drop sides and tailgate on the gooseneck

Condition: new, maximum load weight: 38,400 kg, overall weight: 48,000 kg, axle configuration: 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory, including immediately and short-term available vehicles, on our website. Excerpt from the specifications. Full specification available on request. Loading area: * Extendable loading platform with pneumatically operated locking mechanism * Loading area with approx. 30 mm thick wooden planks * 7 pairs of outward-folding lashing rings (LC 5,000 daN) * 3 pairs of outward-folding lashing rings (LC 10,000 daN) * Cut-outs in the outer frame of the platform for hooking in tension straps (LC 2,000 daN) Landing legs: * JOST mechanical landing legs with 2-speed gearbox, approx. 24 t lifting capacity (approx. 50 t test load) Tyres: * Tyres: 385/65 R 22.5, manufacturer at our discretion * TPMS tyre pressure monitoring system in accordance with ECE R 141. Data transmission to the truck is via the standardized EBS interface as per ISO 11992. For proper display, the truck must be capable of receiving and showing this data. Axle: * BPW axles and suspension * All axles hydromechanically forced-steered * Disc brakes * Technical axle load: 10,000 kg each (offset 0) * Air suspension with raise/lower valve * Axle tools Brake system: * WABCO brake system in accordance with EU regulations, EBS-E (2S2M) without connection lines to the tractor unit Steel construction: * High-strength fine-grain steel construction * Steel grades: S355J2+N/S355MC (yield strength 355 MPa), S690QL/S700MC (yield strength 690 MPa) Electrical system: Gbedpfew Tpr Iox Afnok * Electrical system in accordance with EU regulations * LED lighting 24 Volt ASPÖCK-NORDIK (ASS3) * All LED side marker lights flash together with indicators * ASPÖCK-UNIBOX at the front connection bar with 24N, 24S, and 15-pin sockets according to ISO: 24N ISO-1185, 24S ISO-3731, 15-pin ISO-12098 Paintwork: * Complete steel structure automatically shot-blasted after welding * Second blasting with corundum for optimal coating adhesion * Final painting with two coats of 2-component topcoat, single color, RAL 3002 Carmine Red according to RAL system 841GL * Rims in silver grey * Rear section metallized and painted RAL 9010 (Pure White) * Metallic paint not available * Paint finish tested in salt spray test according to ISO 9227-NSS * Cavity sealing with special wax Accessories: * Remote steering from front and rear via cable remote control with push buttons, with axle tracking monitoring (without installation in the tractor unit) * Electro-hydraulic unit * 4 wheel chocks with holders on the front wall * 2" kingpin * Yellow-red air couplings at the galvanized front connection bar * At gooseneck and rear, left and right, brackets for warning panels, including sockets * 10 pairs of stake pockets for approx. 100 x 50 mm plug-in stakes in the external frame of the loading platform * One galvanized steel front wall (EN12642-XL), approx. 1,600 mm high * 6 pairs of WADER container pockets in the loading area, for 1 x 20' container, 2 x 20' containers, or 1 x 40' container; an additional locking position is provided in the extension for a 45' container * 4 pairs of transverse stake pocket strips in the loading area for approx. 100 x 50 mm plug-in stakes * Storage for max. 9 pairs of plug-in stakes bolted inside to the front wall * Boarding ladder mounted left and right in the direction of travel * One INOX toolbox, approx. 1,200 x 460 x 550 mm, mounted front left under the loading platform * An additional INOX toolbox, approx. 1,200 x 46...

Condition: used, maximum load weight: 51,870 kg, overall weight: 65,000 kg, axle configuration: > 3 axles, first registration: 03/2025, next inspection (TÜV): 03/2026, total width: 2,540 mm, Equipment: ABS, You can find our entire vehicle inventory, including immediately and short-term available vehicles, on our website. Excerpt from the equipment list. Complete equipment details available upon request. GOOSENECK * Gooseneck in SNT design to optimize loading platform length, length approx. 3,700 mm, rear with chamfer approx. 1,000 mm x 10° * For tractors: 4 x 2, 6 x 2, and 6 x 4 * Plug-in steel front wall, approx. 400 mm high * At the front connection strip: yellow-red air couplings * ASPÖCK-UNIBOX on the front connection strip with 24N, 24S & 15-pin sockets * 3 kW electro-hydraulic power unit for hydraulic operations * External beams of the gooseneck with mounting holes for bolted lashing rings * One mounting hole at the rear upper part of the gooseneck external beam for a bolted lashing ring * 1 pair of screw-in lashing rings included (LC 10,000 daN) * On the gooseneck, 1 pair of plug-in side aluminum drop sides, approx. 400 mm high, anodized version * On the gooseneck, 1 plug-in aluminum rear wall, approx. 400 mm high, anodized version * Approx. 40 mm thick hardwood flooring above the gooseneck * 2-inch kingpin * Gooseneck guide plate for fifth wheel, approx. 500 mm wide * Rear gooseneck mounting for aluminum ramps * Round NATO socket at the front connection strip (Maeler & Kaege VG 96 917) LOADING PLATFORM * Loading platform, extendable version, length approx. 8,800 mm, rear with chamfer approx. 500 mm x 10° * Recess in the platform and chamfer for accommodating the excavator dipper stick approx. 2,490 x 750 x 210/290 mm (L x W x H) * TPMS tire pressure monitoring system in accordance with ECE R 141 * BPW axles and suspension * 1st and 2nd axle fixed, 3rd and 4th axles steering trailing axles * 3rd and 4th axles with electro-magnetic reverse lock, activated via reverse gear and manually * Technical axle load: 12,000 kg each * Air suspension with raise and lower valve * 235/75 R 17.5 3PMSF twin tires * Mechanical landing legs with 2-speed gearbox and crank, JOST Module B – static test load approx. 50,000 kg * Complete platform and interrupted between the axles with approx. 50 mm thick hardwood flooring (increasing the coefficient of friction) * Platform locking with conically welded locking profiles every approx. 250 mm * Elongated slots for insertable and repositionable bridging elements at the front of the platform * Intermediate table with set-down platform, approx. 300 mm wide, for large cross-section telescopic tube with sheet metal covering – front and rear with elongated slots for insertable and repositionable bridging elements – removable cover flush with the platform * 1 pair of lashing rings on the front cross member (LC 10,000 daN) * 6 pairs of flush-mounted lashing rings in the outside frame of the platform, foldable outward (LC 10,000 daN) * Additionally, 1 pair of lashing rings externally on the front cross member of the platform, approx. 90° turned inward towards the platform (LC 10,000 daN) * Extendable galvanized widening extensions by approx. 230 mm per side * 1 pair of permanently installed wheel recesses, open up to the extension, approx. 700 x 410 mm (W x D), sheet-covered in the platform ahead of the 1st axle, wheel recesses with square climbing strips approx. 15 x 15 mm, spaced approx. 200 mm Gbodpfx Ajxtc Uhjfnok * Between the 2nd and 3rd axles, 1 pair of permanently installed wheel recesses on the platform, approx. 1,695 x 700 x 410 mm (L x W x D), covers for wheel recesses split lengthwise, with wooden overlay, outer plug-in loc

Condition: new, maximum load weight: 50,400 kg, overall weight: 65,000 kg, axle configuration: > 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory, including units available immediately and at short notice, on our website. Excerpt from the equipment list. Full equipment specifications available on request. GOOSENECK * Gooseneck in SNT design to optimize loading platform length, approx. 3,700 mm long, with rear bevel approx. 1,000 mm x 10° * For tractor units: 4 x 2, 6 x 2, and 6 x 4 * Removable steel front wall, approx. 400 mm high * ASPÖCK-UNIBOX on the front connector strip with sockets * 3 kW electro-hydraulic unit for controlling hydraulic operations, excluding hydraulic winches * 1 pair of removable aluminum side boards, approx. 400 mm high, anodized finish * 1 removable aluminum tailgate, approx. 400 mm high, anodized finish * Approx. 40 mm thick hardwood floor above gooseneck, checker plate floor above king pin * 2-inch king pin * Rear section of gooseneck prepared for aluminum drive-on ramps * Round NATO socket on the front connection strip (Maeler & Kaege VG 96 917) LOADING PLATFORM * Extendable loading platform, approx. 8,800 mm long, with rear bevel approx. 500 mm x 10° * Recess in the loading platform and bevel for accommodating excavator dipper stick approx. 3,850 x 750 x 210/290 mm (L x W x H) * TPMS tire pressure monitoring system per ECE R 141 * BPW axles and suspension, 1st axle steerable, all remaining axles hydro-mechanically forced steered * 1st axle with electromagnetic reverse lockout, activated via reverse gear and manually * Technical axle load: 12,000 kg each, air suspension with raise and lower valve * Tires: 235/75 R 17.5, twin tires, 3PMSF * Mechanical landing legs with 2-speed gearbox and crank, JOST Module B – static test load approx. 50,000 kg * Continuous 50 mm thick hardwood floor on the loading platform and interrupted between axles (increases coefficient of friction) * 1 intermediate table, approx. 300 mm wide, for the extension tube with large cross-section * Extendable (galvanized) side extensions, approx. 230 mm per side (without wooden planks) * Wheel recesses with square climbing strips, approx. 15 x 15 mm ahead of axles, open through to gooseneck cross member, approx. 700 x 410 mm (W x D) * Aluminum covers for wheel recesses, usable as bridging elements for extension OR as widening planks * Aluminum elements lockable on telescopic tubes of the extensions Gbodstx Nwnepfx Afnjk * Widenable U-profiles for inserting ALU covers: - on the fixed section behind the gooseneck - on the intermediate table - on the extendable platform * Wheel recesses with square climbing strips, approx. 15 x 15 mm between 1st and 2nd axle, approx. 1,480 x 700 x 410 mm (L x W x D) * Aluminum covers for the wheel recesses, usable as bridging elements for the extension OR as widening planks * Aluminum elements lockable on the extension’s telescopic tubes * 1 pair of mechanical rear supports * Remote steering from front and rear via cable remote control, with axle tracking, without installation in the tractor unit HYDRAULIC LOADING RAMPS * One pair of two-section steel ramps, Type: DR-15/60-900-4350-KG-HV-M, approx. 4,350 mm in length and approx. 900 mm wide each * Hydraulically foldable ramp tips * Ramps can be shifted hydraulically approx. 235 mm outward and approx. 215 mm inward individually * Super Grip rubber surface approx. 25 mm and steel plate surface approx. 5 mm as additional

Condition: new, maximum load weight: 33,865 kg, overall weight: 48,000 kg, axle configuration: 3 axles, Equipment: ABS, You can find our complete range of vehicles, including those available for immediate delivery or on short notice, on our website. Below is an excerpt from the specification. The full equipment list is available upon request. Gooseneck: * Gooseneck with front corners chamfered approx. 45° and a rear bevel approx. 750 mm x 10° * 3 pairs of lashing rings (LC 5,000 daN) Gedpsw Tprzjfx Afnjbk * Hardwood flooring approx. 30 mm thick Load area: * Double extendable design with rear bevel approx. 500 mm x 8° * 6 pairs of folding external lashing rings (LC 5,000 daN) * 4 pairs of folding external lashing rings (LC 10,000 daN) * 1 pair of recessed lashing rings at the front of the loading area (LC 10,000 daN) * 1 intermediate table approx. 250 mm * Hardwood flooring approx. 48 mm thick, over axles with checker plate covering * Cut-outs in the external frame of the loading platform for attaching tie-down straps (LC 2,000 daN) Axles: * BPW axles and suspension, all axles forced-steered hydro-mechanically * Design axle load: 12,000 kg each * Air suspension with lift and lower valve * Axle tools included Tyres: * 245/70 R 17.5, load index (146/146 F) * Brand of our choice Landing legs: * JOST mechanical landing legs with 2-speed gearbox for approx. 24 t lifting capacity (approx. 50 t test load) Braking system: * Braking system according to EU regulations with EBS-E (2S2M) without connection lines to the tractor unit Paintwork: First-class and durable corrosion protection * High-quality, one-colour 2-component (2K) topcoat in RAL 3002 carmine red * Rear section metallized and coated in RAL 9010 (pure white) Steel Structure: Steel construction from high-strength fine grain steels. * Steel grades: S355J2+N/S355MC (yield strength 355 MPa), S690QL/S700MC (yield strength 690 MPa) Electrical system: * Electrical system according to EU regulations * 24 Volt lighting ASPÖCK-NORDIK (ASS3) * ASPÖCK-UNIBOX at the front connection strip with 24N, 24S & 15-pin sockets, compliant with ISO. 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Including the following additional equipment: * 2-inch kingpin * Galvanized steel front wall, approx. 400 mm high * Yellow-red air couplings at the galvanized front connection strip * Spare wheel carrier in front of the front wall * Electro-hydraulic unit * Rear and front steering via cable remote control with push-buttons, with single-track monitoring of the axles (without installation in the tractor unit) * Mount at the rear of the gooseneck for aluminum loading ramps * Removable aluminum ramp hanging rail at the rear of the vehicle * Galvanized folding supports beneath the slope of the load area * On the gooseneck: plug-in aluminum side boards and rear board, approx. 2,440 x 400 mm (L x H) * The rear galvanized stanchions are removable (body length approx. 2,560 mm) * One galvanized toolbox, integrated in the chamfered gooseneck * 4 pairs of WADER container pockets in the loading area for one 20', two 20', one 40' or one 45' container * 8 pairs of stanchion pockets (approx. 100 x 50 mm) in the external frame of the loading platform * Galvanized extensions, extendable by approx. 230 mm per side * Adjustable hanging rails for aluminum ramps at the rear of the vehicle * 2 pairs of ferry rings under the gooseneck and 2 pairs at the rear * Central lubrication system with 2 BEKAMAX (Pico) pumps, filled with standard grease NLGI-2 and removable pump guard * 2 LED reversing lights mounted on the rear panel * HRM Metallization (High Resistance Metallisa

Condition: new, maximum load weight: 37,680 kg, overall weight: 50,960 kg, axle configuration: > 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete inventory of vehicles, including those available for immediate and short-term delivery, on our website. Extract from the equipment features. Complete specification available on request. Gooseneck * With approximately 30 mm thick hardwood flooring. Gooseneck with straight rear section * 3 pairs of lashing rings (LC 5,000 daN) Loading Area * Extendable design * 5 pairs of outward-folding lashing rings (LC 5,000 daN) * 3 pairs of outward-folding lashing rings (LC 10,000 daN) * 1 pair of recessed lashing rings at the front of the loading area (LC 10,000 daN) * Cutouts in the outer frame of the loading area for attaching tension straps (LC 2,000 daN) * Approx. 48 mm thick hardwood flooring, treadplate covering above the axles Landing Gear * JOST mechanical landing gear with 2-speed gearbox, lifting capacity approx. 24 t (test load approx. 50 t) Tyres * 205/65 R 17.5 Axles * BPW axles and suspension * 1st axle fixed, all other axles hydro-mechanically forced-steered Gbsdpfev Etx Eex Afnsk * Air suspension with lift and lower valve Brake System * In accordance with EU regulations, with EBS-E (4S3M) without connection lines to the tractor unit Steel Construction * Made of high-strength fine-grained steels * Steel grades: S355J2+N/S355MC (yield strength 355 MPa), S690QL/S700MC (yield strength 690 MPa) Paintwork * Premium and durable corrosion protection for the standard shot-blasted welded frame, guaranteed by a two-component (2K) zinc dust primer * High-quality two-component (2K) top coat, single colour RAL 3002 carmine red * Rims in silver Accessories Included * 2" king pin * Galvanised steel front wall, approx. 400 mm high * Yellow-red air couplings on galvanised front connection strip * 4 chocks with holder on the front wall * Spare wheel holder in front of the front wall * Electro-hydraulic unit * Steering from the front and rear via cable remote control with push buttons, including single-track control of the axles (without installation in the tractor unit) * European reflective signs (red-yellow) at the rear of the trailer * Yellow reflective tape according to EU regulations on sides, extensions, and rear of the trailer * Bracket for warning signs including socket, left and right on the gooseneck and rear plate * Bracket for rotating beacon at the rear of the trailer * Galvanised foldable support legs under the loading area's chamfer * Load gauge for determining axle loads including load diagram * 7 pairs of WADER container pockets for: 1x 20' or 1x 40' container on the loading area, 1x 40' container over the gooseneck, or 2x 20' containers * Support block with 1 pair of WADER container pockets, fifth wheel load approx. 20,000 kg * 7 pairs of stake pockets for approx. 100 x 50 mm plug-in stakes in the outer frame of the loading area * Galvanised, extendable width extensions, approx. 230 mm per side * Sliding hook-in rails for aluminium loading ramps at the rear of the vehicle * 1 pair of recessed lashing rings along the central beam at the rear of the loading area (LC 10,000 daN) * 2 pairs of ferry rings under the gooseneck and 2 pairs at the rear * BEKAMAX (Pico) central lubrication system with standard grease NLGI-2 and removable pump protection * 2 LED reversing lights mounted at the rear * Acoustic reversing warning signal * HRM Metallisation (High Resistance Metallisation)

Condition: new, maximum load weight: 39,720 kg, overall weight: 50,960 kg, axle configuration: > 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory, including immediately and short-term available vehicles, on our website. Sample equipment features. Full specification upon request. Gooseneck * With beveled front corners approx. 45° and rear bevel approx. 750 mm x 10° * 3 pairs of lashing rings (LC 5,000 daN) * Hardwood flooring, approx. 30 mm thick Loading Platform Loading platform in extendable design * 5 pairs of fold-out outer lashing rings (LC 5,000 daN) * 3 pairs of fold-out outer lashing rings (LC 10,000 daN) * 1 pair of recessed lashing rings at the front of the loading platform (LC 10,000 daN) * Recesses in the outer frame of the loading platform for securing straps (LC 2,000 daN) * Hardwood flooring approx. 48 mm thick, over axles with chequer plate covering Landing Gear * JOST (mechanical) with 2-speed gearbox, approx. 24 t lift capacity (approx. 50 t test load) Axles * BPW axles: 2 fixed axles, 2 steering axles, drum brakes * Air suspension with lift/lower function * Self-steering axle with electro-magnetic reverse lock, activated via reverse gear or manually * Tires: 205/65 R 17.5 Brake System * Wabco brake system in accordance with EU directives with EBS-E (4S3M), without interconnecting lines to the tractor unit Steel Construction * Made of high-strength fine-grained steels * Steel grades: S355J2+N/S355MC (yield strength 355MPa), S690QL/S700MC (yield strength 690MPa) Paintwork * First-class, durable corrosion protection of the standard shot-blasted welded frame, guaranteed by a 2-component (2K) zinc dust primer * High-quality 2-component (2K) top coat, single-color, RAL 3002 Carmine Red * Rear section metallized and painted in RAL 9010 (Pure White) * Rims in silver Accessories Included * 2-inch king pin * Galvanized front steel bulkhead approx. 400 mm high * Spare wheel holder in front of bulkhead * Yellow-red air couplings on galvanized connector bar front * 4 wheel chocks with holder at bulkhead Godpfeu Sd U Uex Afnobk * Bracket at rear of gooseneck for aluminum loading ramps * Galvanized folding supports under inclined edge of loading platform * Holder for beacon at rear of trailer * Yellow reflective tape on sides, extension, and rear in accordance with EU regulations * Brackets for warning signs with socket on both sides at the gooseneck and rear panel * TPMS tire pressure monitoring system per ECE R 141. Data transmission to the tractor unit via standardized EBS interface according to ISO 11992; for correct display, the tractor unit must support data transmission and display * Plug-in aluminum side walls and tailgate on gooseneck, approx. 2,440 x 400 mm (L x H); rear galvanized stakes are removable (body length approx. 2,560 mm) * Galvanized toolbox, integrated in gooseneck slope * 6 pairs of WADER container locks in loading platform, for 1 x 20' container, 2 x 20' containers or 1 x 40' container * Sliding mounting rails for aluminum ramps at rear of vehicle * 7 pairs of stake pockets for plug-in stakes approx. 100 x 50 mm, in the outer frame of the loading platform * Galvanized cross bracket under the loading platform * Galvanized extendable widenings, extendable approx. 230 mm per side * Lift axle on front axle, controlled via TEBS E according to current axle load and load status * 5 pairs of recessed lashing rings along the central beam (LC 5,000 daN)

Condition: new, maximum load weight: 52,810 kg, overall weight: 63,000 kg, axle configuration: > 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete range of immediately and soon available vehicles on our website. Excerpt from the equipment list. Full specifications available on request. Cargo area: * Cargo area with approx. 30 mm thick hardwood floor * 10 pairs of folding external lashing rings (LC 10,000 daN) Landing legs: * Hydraulic landing legs TPMS: * TPMS tire pressure monitoring system compliant with ECE R 141. Data transmission to the tractor unit is via the standardized EBS interface according to ISO 11992. For correct display, the tractor must be capable of transmitting and displaying these data. Axles and suspension: * BPW axles, technical capacity 12,000 kg each, first axle fixed, all others hydro-mechanically forced-steered, mounted on turntables * Air-suspended with lift and lower valve * Axle toolkit Tires: * Tires 445/65 R 22.5 169 K Electrical system: Gsdpfx Afsxttc Asnobk * Electrical system in accordance with EU regulations, lighting 24 Volt ASPÖCK-NORDIK (ASS3) * ASPÖCK-UNIBOX at the front connection strip with 24N, 24S & 15-pin sockets * Connections according to standards. 24N ISO-1185, 24S ISO-3731, 15-pin ISO-12098 Brake system: * Wabco brake system compliant with EU regulations, with EBS-E (4S3M), without connecting lines to the tractor unit Steel construction: * Steel construction made of high-strength fine-grain steels * Steel grades: S355J2+N/S355MC (yield point 355MPa), S690QL/S700MC (yield point 690MPa) Painting: * Complete steel structure automatically shot-blasted after welding using a shot-blasting machine * Secondary blasting with corundum for optimal adhesion of the coating system * Final painting with 2 coats of 2K topcoat, single color in RAL 1007 Narcissus Yellow according to RAL system 841GL * Rear section metallized and painted in RAL 9010 Pure White * Wheels in Silver Grey * Paint structure tested in salt spray test according to ISO 9227-NSS * Cavity sealing with special wax Including accessories: * Cargo area with approx. 30 mm thick hardwood floor * 2-inch king pin * One galvanized steel front wall (EN12642-XL), approx. 1,200 mm high * Yellow-red air couplings on the galvanized front connection strip * On the gooseneck and rear panel left and right, each with a bracket for warning signs including socket * Rear steering from the front and rear by cable remote control via push buttons, with single-track control of the axles (without installation in the tractor unit) * Electro-hydraulic unit * 12 pairs of stake pockets for approx. 100 x 50 mm stakes in the outer frame of the cargo area * Load manometer for determining axle loads including load diagram * Lift axle on the front axle, controlled by TEBS E * 5 pairs of crosswise stake pocket rails on the cargo area, for approx. 100 x 50 mm stakes * One INOX toolbox 1,200 x 460 x 550 mm mounted at the front left under the cargo area (in direction of travel) * 1 shunting coupling with reinforcement bolted to the rear cross member * BEKAMAX (Pico) automatic central lubrication system with standard grease NLGI-2 and removable pump guard * 2 LED reversing lights mounted on the rear panel * HRM metallization of the entire vehicle chassis with ZINACOR 850 (85% zinc/15% aluminum)

Condition: used, functionality: fully functional, empty load weight: 10,700 kg, first registration: 06/2015, Year of construction: 2015, FAYMONVILLE Max Trailer F-S44-1A1Y Length: 13,050 mm Width: 2,550 mm Front tire: 235/75R17.5 Rear tire: 235/75R17.5 Wheelbase: 1,360 mm Total permissible weight: 40,000 kg Payload: 29,300 kg Empty weight: 10,700 kg Equipment: Cable winch 2" kingpin Gbedpfsvx R Nhjx Afnok Operation via 2-pin NATO connector 4 SAF axles 2x steerable ABS Rear support ESB Hydraulic loading ramps (steel ramps) Telescopic Drum brake

Condition: new, empty load weight: 12,300 kg, maximum load weight: 37,200 kg, overall weight: 49,500 kg, axle configuration: 3 axles, loading space length: 9,300 mm, loading space width: 2,480 mm, loading space height: 860 mm, suspension: air, tire size: 235/75 R17.5, color: grey, Equipment: ABS, Gooseneck: -Gooseneck with rear bevel of approx. 750 mm x 10° -Hardwood covering 30 mm thick Two-piece steel ramps: -A pair of galvanized two-part steel ramps approx. 3,185x1,420x1,250 mm with grating decking -Ramp with hydraulically folding and unfolding ramp sections, hydraulic lifting gear Gooseneck: -Gooseneck with rear bevel of approx. 750 mm x 10° -3 pairs of lashing rings -Hardwood decking 30 mm thick Two-part steel ramps: -One pair of galvanized two-part steel ramps approx. 3,185x1,420x1,250 mm with grating covering -Ramp with hydraulically folding and unfolding ramp sections, hydraulic lifting gear -Maximum load per pair: 30,000 kg Loading area: -Loading surface with rear slope of approx. 1,000 mm x 8° -Hardwood flooring approx. 48 mm thick, checker plate flooring over the axles Axles and tires: -BPW axles and suspension, two axles rigid, one axle self-steering -Air suspension with lifting and lowering valve The self-steering axles with electro-magnetic reverse lock can be activated via reverse gear or manually -235/75 R17.5 3PMSF tires Accessories included: -1 Spare wheel with holder -TPMS tire pressure monitoring system according to ECE R 141 -2" kingpin -Galvanized steel bulkhead -Yellow-red air couplings on the galvanized front connecting strip -4 restraining shoes with holder on the bulkhead -Mounting in the rear area of the gooseneck for ALU docking ramps -3 height aluminum boards -Galvanized folding supports under the bevel of the cargo bed Height-adjustable tarpaulin superstructure (3,960 mm) -Galvanized bulkhead with a tensioning mechanism for the sliding curtain -Height-adjustable by approx. 400 mm -"EDSCHA" brand roof can be moved forwards on ALU roof rail profiles bolted to the front and rear wall -3 pairs of sliding stanchions in the loading area -The body can be hydraulically widened at the rear to the left and right by approx. 750 mm -Sliding roof with pivoting portal support -Sliding tarpaulin with 700 mm reserve in length, with tension belts at approx. 600 mm intervals -Height top edge of body approx. 3,960 mm -Driving with the sliding tarpaulin open is not permitted and will damage the tarpaulin -Cover plates to bridge the free space between ramps and loading area -Electric hydraulic unit at the rear, under the cargo bed -On the gooseneck and on the ramps on the left and right, one bracket each for the warning signs including socket -Control valves for the ramps mounted on the right-hand side of the trailer -6 pairs of stanchion pockets for 100 x 50 mm stanchions in the outer frame of the cargo bed -Lift axle on the front axle -Grating in the bevel of the loading area C40/4 (point load 3.4 tons on an area of 20 x 20 cm) -One INOX toolbox 565 x 290 x 810 mm in the direction of travel on the right between the axles -A layer of sand painted onto the chequer plates on the gooseneck and on the loading area to prevent slipping Gbodpstvfkfofx Afnok -BEKAMAX (Pico) central lubrication system with NLGI-2 standard grease and removable protection around the pump -Four warning panels approx. 423 x 423 mm, extendable by approx. 400 mm, with a position light -Load manometer for determining the axle loads including load diagram -HRM metallization (High Resistance Metallization) of the outer frame -Complete steel construction shot-blasted, then the defined visible surfaces hot-finished in metallization with ZINACOR 850 (zinc 85% - aluminium 15%)

Condition: used, empty load weight: 14,995 kg, maximum load weight: 50,805 kg, overall weight: 65,800 kg, axle configuration: > 3 axles, first registration: 10/2023, loading space length: 9,300 mm, loading space width: 2,540 mm, loading space height: 900 mm, suspension: air, tire size: 235/75 R17.5, color: grey, Year of construction: 2023, operation weight: 14,995 kg, Equipment: ABS, You will receive a current and complete inspection and functional report for every used trailer. Gooseneck: -Gooseneck with rear bevel of approx. 750 mm x 10° -3 pairs of lashing rings (LC 5,000 daN) -Hardwood covering 30 mm thick Loading area: -Loading area in extendable version with rear bevel of approx. 500 mm x 8° -6 pairs of lashing rings that can be folded outwards (LC 5,000 daN) -4 pairs of lashing rings that can be folded outwards (LC 10,000 daN) -1 pair of lashing rings lying in the front of the loading area (LC 10,000 daN) -1 intermediate table 250 mm -Cutouts in the outer frame of the loading area for hanging tensioning straps (LC 2,000 daN) -Hardwood covering approx. 48 mm thick, checkered sheet covering above the axles Axles and Tires: -BPW axles with hydro-mechanical forced steering -Technical axle load: 12,000 kg -Air suspension with lifting and lowering valve -Axle tool -Tires 235/75 R17.5 Braking system: -Braking system in accordance with EU regulations with EBS-E (4S3M) Accessories included: -2" kingpins -A galvanized steel bulkhead approx. 400 mm high -Yellow-red air couplings on the galvanized connection strip at the front -4 brake shoes with holder on the bulkhead -A spare wheel with holder in front of the bulkhead -Electro-hydraulic unit -Steering from the front and rear can be operated using a cable remote control via push buttons, with alignment control of the axles -Mounting in the rear area of the gooseneck for aluminum docking ramps -Galvanized extensions, extendable by approx. 230 mm on each side -European reflector signs (red-yellow) on the rear of the trailer Gedpfxsv Hr Axs Afnebk -White reflector tape in accordance with EU regulations on the side, on the extension and at the rear, red -On the gooseneck and on the rear panel, left and right, a bracket for the warning signs including a socket -Galvanized folding supports under the slope of the loading area -A bracket for a rotating beacon at the rear of the trailer -Central lubrication system with 2 BEKAMAX (Pico) pumps with normal grease NLGI-2 and removable protection around the pump -A mud flap at the rear of the trailer -Manual and description -ALU side walls and rear wall can be plugged into the gooseneck, approx. 2,440 x 400 mm -The rear galvanized plug-in stanchions are removable (length of the body approx. 2,560 mm) -4 pairs of WADER container pockets in the loading area for a 20ft, 2x 20ft, 40ft or a 45ft container -8 pairs of stake pockets for 100 x 50 mm stakes in the outer frame of the loading area -Movable mounting rails for aluminum ramps at the rear of the vehicle -Lift axle on the front axle with control by TEBS E depending on the current axle load and the current loading status -Four warning signs, approx. 423 x 423 mm, extendable by approx. 400 mm, with a position light -A holder for a rotating beacon on the warning signs -Radio remote control for the steering in addition to the cable remote control, with indicator lights on the receiver as a lane control -A painted layer of sand on the checker plates, above the kingpin and the loading area as a slip protection device -Speed sticker 80 km/h at the rear -Load pressure gauge for determining the axle loads including load diagram

Condition: used, maximum load weight: 65,350 kg, overall weight: 78,000 kg, axle configuration: > 3 axles, first registration: 05/2020, With air suspension, hydraulic dual-circuit forced steering (turntable) - "Platform" crane ballast design - Corners at right angles, closed external frame - Front linkage integrated into the frame Gbjdpfxex I U Eqj Afnek - Fifth wheel plate with ball bearing slewing ring, replaceable 3.5" king pin and adjustable steering wedge - Fifth wheel load: 28,000 kg - Maximum steering angle: 2,700 mm Chassis - 5-axle chassis with air suspension including lift and lower valve - Axles: SAF brand - Tires: 445/65 R 22.5 Brake system - Two-line all-wheel compressed air brake system with diaphragm brake cylinders - Automatic load-dependent brake (ALB) - Automatic slack adjusters (AGS) - Parking brake via spring-loaded cylinders - Anti-lock braking system (ABS) - 1st and 2nd axles liftable (in direction of travel) Technical data Cargo area (LxW): approx. 12,500 x 2,550 mm Coupling dimension B: 11,550 mm Loading height loaded (chassis area): approx. 1,490 mm at a loaded fifth wheel height: 1,200 mm Steering 1st axle: forced-steered 2nd axle: rigid 3rd - 5th axle: hydromechanical forced steering (dual-circuit steering) Radio remote control Electric power pack