Used Müller-Mitteltal Ka Trailers for sale (270)

Condition: new, maximum load weight: 6,870 kg, overall weight: 9,900 kg, axle configuration: 1 axle, Year of construction: 2026, * KWH 9.9 ML: ----Brakes: * EBS braking system * Drum brake * Emergency release device for spring-loaded cylinders ----Axle: * BPW axle ----Suspension: * Parabolic springs ----Drawbar / Flange drawbar: * Drawbar with 40 mm threaded drawbar coupling (height-adjustable in mm) ----Electrical system / Lighting: * 15-pole power plug * LED lighting * Flashing LED side marker lights * TPMS tire pressure monitoring system ----General components: * Front support jack * Spring-supported square tube supports at the rear with base plate, safety locking pins for different support heights * Closed mudguards made of sheet steel with splash protection * Closed side impact protection, can be used as an advertising space * Plastic tool box with base insert (horizontal installation) approx. 500 x 350 x 400 mm ----Superstructure: * Swiveling cable drum superstructure, width between the drum arms 1,700 mm with a clamping device to secure the drum at the ends of the support arms, and a locking mechanism for the cable drum superstructure with the chassis using a centrally arranged claw lock * Motor-hydraulic drum drive with oil motor * Valves and sliding, rubber-coated drive rollers * Hydraulic speed regulator and brake for drum drive * Steel drum shaft with 76 mm diameter, centering, and rotatable ends * 1 pair of centering cones made of polyamide, stepped ----Chassis: * Chassis made of torsion-resistant square tubes and cross members ----Pump unit: * Hydraulic pump unit with diesel engine * Fuel tank and manual starter * 6.5 HP with gear pump (150 bar) Gkedpfx Apeu I Iqxsqoa ----Tires: * 315/80 R 22.5 ----Unladen weight: * 2,690 kg unladen weight ----Painting: * Vehicle is hot-dip galvanized ----Information: * New vehicle with full manufacturer's warranty * Errors and prior sale excepted ----Delivery time: * Immediately available from Egestorf

Condition: new, maximum load weight: 6,870 kg, overall weight: 8,800 kg, axle configuration: 1 axle, Year of construction: 2026, * KWH 9.9 ML: ----Brakes: * EBS braking system * Drum brake * Emergency release device for spring-loaded cylinders ----Axle: * BPW axle ----Suspension: * Parabolic springs ----Drawbar / Flange coupling: * Drawbar with 40 mm screwed coupling (height-adjustable, in mm) ----Electrical system / Lighting: * 15-pole power connector * LED lighting * Flashing LED side marker lights * TPMS (Tire Pressure Monitoring System) ----General components: * Front support jack * Spring-assisted square tube supports at the rear with base plate, safety locking pins for various support heights * Closed steel sheet fenders with splash guards * Closed side impact protection, usable as an advertising space * Plastic toolbox with base insert (horizontal installation), approx. 500 x 350 x 400 mm ----Superstructure: * Swiveling cable drum superstructure, width between the drum arms 1,700 mm with a clamping mechanism to secure the drum at the end of the support arms, and a locking mechanism for the cable drum superstructure with the chassis by means of a centrally arranged claw lock * Motor-hydraulic drum drive with oil motor * Valves and adjustable rubber-coated drive rollers * Hydraulic speed control and brake for drum drive * Steel drum shaft with 76 mm diameter, centering and rotatable ends * 1 pair of centering cones made of polyamide, stepped ----Chassis: * Chassis made of torsionally rigid square tubes and cross members ----Pump - Unit: * Hydraulic pump unit with diesel engine * Fuel tank and manual starter Gsdpfx Apju I Iqljqeka * 6.5 HP with gear pump (150 bar) ----Tires: * 315/80 R 22.5 ----Unladen weight: * 2,690 kg unladen weight ----Paintwork: * Vehicle is hot-dip galvanized ----Information: * New vehicle with full manufacturer's warranty * Errors and prior sale are subject to change ----Delivery time: * Available for immediate delivery from Egestorf

Condition: new, maximum load weight: 6,870 kg, overall weight: 9,900 kg, axle configuration: 1 axle, Year of construction: 2026, * KWH 9.9 ML: ----Brakes: * EBS braking system * Drum brake * Emergency release device for spring-loaded cylinders ----Axle: * BPW axle ----Suspension: * Parabolic springs ----Drawbar / Flange drawbar: * Drawbar with 40 mm threaded drawbar eye (height-adjustable in mm) ----Electrical system / Lighting: * 15-pole electrical connector * LED lighting * Flashing LED side marker lights * TPMS (Tire Pressure Monitoring System) ----General components: * Front support winch * Spring-assisted square tube supports at the rear with base plate, safety locking pins for various support heights * Enclosed fenders made of sheet steel with splash guard * Enclosed side impact protection, can be used as an advertising surface * Plastic toolbox with bottom insert (horizontal installation), approx. 500 x 350 x 400 mm ----Superstructure: * Swiveling cable drum superstructure, width between the drum arms 1,700 mm, with clamping mechanism for securing the drum at the ends of the support arms, as well as a locking mechanism of the cable drum superstructure to the chassis by means of a centrally arranged claw lock * Motor-hydraulic drum drive with oil motor * Valves and sliding, rubber-coated drive rollers * Hydraulic speed control and brake for drum drive * Steel drum shaft with 76 mm diameter, centering and rotatable ends * 1 pair of centering cones made of polyamide, stepped ----Chassis: * Chassis made of torsion-resistant square tubes and cross members ----Pump unit: * Hydraulic pump unit with diesel engine * Fuel tank and manual starter * 6.5 HP with gear pump (150 bar) ----Tires: * 315/80 R 22.5 Gkodpfxju I Iq Ee Apqsa ----Unladen weight: * 2,690 kg unladen weight ----Paint finish: * Vehicle is hot-dip galvanized ----Information: * New vehicle with full manufacturer's warranty * Errors and prior sale excepted ----Delivery time: * Immediately available from Egestorf

Condition: new, maximum load weight: 6,900 kg, overall weight: 9,900 kg, axle configuration: 1 axle, Year of construction: 2026, * KWH 9.9 ML: ----Brakes: * EBS braking system * Drum brake ----Axle: * BPW axle ----Suspension: * Parabolic springs ----Electrical System / Lighting: * TPMS (Tire Pressure Monitoring System) * 15-pin electrical connector * LED lighting * Flashing LED side marker lights ----Drawbar / Flange Coupling: * Drawbar with 40 mm screw coupling (height adjustable in mm) ----General Components: * Front support jack * Spring-supported square tube supports at the rear with base plate, safety locking pins for different support heights * Closed steel sheet mudguards with splash protection * Closed side impact protection, usable as an advertising area * Plastic toolbox with floor insert (horizontal installation), approx. 500 x 350 x 400 mm ----Superstructure: * Swiveling cable drum superstructure, width between the drum arms 1,700 mm, with tensioning closure for securing the drum at the ends of the support arms, as well as a locking mechanism for the cable drum superstructure with the chassis via a centrally arranged claw lock * Motor-hydraulic drum drive with oil motor * Valves and adjustable rubber-coated drive rollers * Hydraulic speed controller and brake for drum drive * Steel drum shaft with 76 mm diameter, with centering and rotatable ends * 1 pair of centering cones made of polyamide, stepped arrangement * Preparation of steel structure and hydraulics for retrofitting a separate motor ----Chassis: * Chassis made of torsion-resistant square tubes and cross members Gedpfx Apjxyniwsqoka ----Hydraulics: * Hydraulic line for supply and return ----Tires: * 315/80 R 22.5 tires ----Painting: * Vehicle is hot-dip galvanized ----Information: * 2,690 kg unladen weight * New vehicle with full manufacturer warranty * Errors and prior sale excepted ----Delivery time: * Available for immediate delivery from Egestorf

Condition: new, maximum load weight: 29,850 kg, overall weight: 38,000 kg, axle configuration: 2 axles, loading space length: 8,000 mm, loading space width: 2,520 mm, Year of construction: 2026, TS 2 ML ----Brakes: * EBS-E (electronic braking system) * Emergency release device for spring brake cylinders * Drum brakes ----Axles: * 2 x 10 t axles * Last axle as a trailing steering axle with electro-pneumatic steering lock activated by PIN in reverse gear * Additional lock for the trailing axle, operable from the driver's cab for maneuvering purposes – without truck-side installation – assigned to PIN 10; the lock must be disengaged before driving on public roads ----Suspension: * Air suspension with lift and lower function and RtR (Ride to Reduce) function ----Electrics / Lighting: * Tire pressure monitoring system with display capability in the truck's display via EBS signal – without truck-side installation * LED tail lights 12 / 24 V * Flashing side marker lights * LED reverse lights activated by reverse gear * SmartBoard installed as info tool with pressure sensors solely for total axle load display * 7-pin socket at the rear for illumination of overlength loads * LED beacon (removable) at the rear ----General Attachments: * Aluminum air tanks * Manual crank landing gears * Galvanized steel mudguards * Swivel arm as carrier for connection lines in front of the front bulkhead ----Warning Package: * Mechanically adjustable warning sign package ----Lowbed Platform: * 50 mm thick flooring made from larch / Douglas fir instead of spruce / fir * Rear slope – 700 mm long – on the semi-trailer deck to the low bed with checker plate covering and at the end a perforated strip for attaching aluminum drive-on ramps * Tread plate cover over the wheels * SP combo package: toolbox with 45° corners made of galvanized sheet steel, additionally powder-coated in RAL 9006 white aluminum color, mounted on the semi-trailer platform approx. 2,480 x 500 mm * Hinged lid on top and side doors in the angled corners * Fold-down aluminum side boards, 500 mm high on the trailer platform, incl. foldable and removable rear stanchions * Plug-in aluminum rear wall, 150 mm high * 2nd kingpin position Godpfjykx I Hsx Apqeka * Preparation for container locks * Preparation for 3 receiving pockets in the transition slope from lowbed to gooseneck * Preparation for retrofitting folding outriggers to achieve 3-meter width, including welded-in mounting brackets in the outer frame ----Load Securing: Semi-trailer platform: * 50 mm holes in the front corners and front for 1.2 t lashing force per hole * 2 x 16.5 t lashing rings recessed in the floor at the side near the approach slope * Perforated, 45°-bent outer frame with hole pattern for lashing equipment (2 t lashing points every 480 mm) * Each side with 2 x 6.3 t retractable lashing rings recessed in the outer frame Low-bed platform: * 2 x 16.5 t lashing rings recessed centrally just in front of the approach slope to the gooseneck * Each side with 3 pairs of 13.5 t and 5 pairs of 10 t retractable lashing rings recessed into the outer frame * Each side with 4 stake pockets recessed into the outer frame * Profifix lashing rail in the center longitudinal axis (lashing capacity 3 t per lashing circuit) ----Excavator Arm Rest: * From end of last rigid axle to end cross member B = 770 mm, D = 270 mm (each side with 2 x 6.4 t lashing rings welded in place in the excavator arm rest) ----Ramp: * Hydraulic one-piece "ALLTEC" aluminum drive-on ramps, approx. 3,200 x 750 mm * Load capacity 13 t per ramp (26 t/pair) * Hydraulic ramp shifting on sliding tube of the ramp shaft ----Hydraulics: * Hydraulic flow divider in the trail

Condition: new, maximum load weight: 29,850 kg, overall weight: 38,000 kg, axle configuration: 2 axles, loading space length: 8,000 mm, loading space width: 2,520 mm, Year of construction: 2026, TS 2 ML ----Brakes: * EBS-E (electronic braking system) * Emergency release device for spring brake cylinders * Drum brakes ----Axles: * 2 x 10 t axles * Rear axle as a trailing steering axle with electro-pneumatic steering lock activated by PIN when reverse gear is selected * Additional lock for the trailing axle, operated from the driver's cab for maneuvering purposes – no truck-side installation required – assigned to PIN 10. The lock must be deactivated before driving on public roads ----Suspension: * Air suspension with lifting and lowering function as well as RtR (Ride to Recover) function Gedpoykx I Tsfx Apqska ----Electrics / Lighting: * Tire pressure monitoring system with display option in the truck dashboard via EBS signal – no truck-side installation required * LED tail lights 12 / 24 V * Flashing side marker lights * LED reversing lights switched via reverse gear * SmartBoard installed as info tool with pressure sensors exclusively for total axle load display * 7-pin socket at the rear for overlength lighting * Removable LED rotating beacon at the rear ----General attachments: * Aluminum air tanks * Mechanical crank landing legs * Galvanized steel mudguards * Swivel arm as a carrier for connection lines mounted in front of the front panel ----Warning package: * Mechanically adjustable warning sign package ----Low-bed platform: * 50 mm flooring made of larch / Douglas fir instead of spruce / fir * Rear slope – 700 mm long – on the gooseneck deck to the low-bed with checker plate covering, and perforated strip at the end for attaching aluminum approach ramps * Tread plate cover over wheels * SP-Combo package: toolbox with 45° corners, made of galvanized sheet steel, additionally powder-coated in RAL 9006 white aluminum, mounted on the platform approx. 2,480 x 500 mm * Flip-top lid as well as side doors in the slanted corners * Folding aluminum side walls 500 mm high on the platform, incl. folding and removable rear stanchions * Plug-in aluminum rear wall 150 mm high * Second kingpin position * Preparation for container lock * Preparation for 3 insert pockets in the inclined ramp from low-bed to gooseneck * Preparation for retrofitting folding outriggers for 3 m widening by welding the mounting brackets into the outer frame ----Load securing: Fifth wheel platform: * In the front corners and at the front, 50 mm holes for 1.2 t lashing force per hole * 2 x 16.5 t lashing rings recessed in the floor on the side at the approach slope * Perforated and bent 45° outer frame with hole pattern for lashing equipment (2 t lashing points every 480 mm) * On each side: 2 x 6.3 t retractable lashing rings recessed into the outer frame Low-bed platform: * 2 x 16.5 t lashing rings recessed centrally directly in front of the approach slope to the gooseneck * On each side: 3 pairs of 13.5 t and 5 pairs of 10 t retractable lashing rings recessed into the outer frame * On each side: 4 stanchion pockets recessed into the outer frame * Profifix lashing rail centered in the longitudinal axis (lashing point 3 t per securing circle) ----Excavator arm trough: * From the end of the last rigid axle to the end cross member B = 770 mm, D = 270 mm (on each side 2 x 6.4 t lashing rings for the excavator arm trough, permanently welded) ----Ramp: * Hydraulic one-piece "ALLTEC" aluminum approach ramps approx. 3,200 x 750 mm * Load capacity 13 t per ramp (26 t per pair) * Hydraulic ramp shifting on sliding pipe of the ramp shaft ----Hydraulics: * Hydraulic flow

Condition: used, maximum load weight: 38,230 kg, overall weight: 48,000 kg, axle configuration: 3 axles, first registration: 06/2026, loading space length: 8,500 mm, loading space width: 2,520 mm, Müller-Mitteltal Low-loader with Wheel Recesses TS 3 RM ML 30.0, 2 Loading Heights and Ramps * Fifth wheel load increase from 12 t to 18 t incl. Kingpin mounted in: Second kingpin position 2", kingpin up to and incl. 5th wheel height 2,750 mm. Rear turning radius approx. 2,400 mm in clear width (a minimum clearance of 150 mm is recommended). Forward turning radius 1,480 mm or 1,570 mm with spare wheel. Note: Sufficient clearance to the towing vehicle must be ensured by the customer. * Extension parts for the wheel recesses at the front and bottom at the rear (205 mm deep). 6 pieces incl. insertion boards for wheel recesses at the rear. Board holder as receiving shafts according to code 09.112. Aluminum compressed air tank instead of steel. * Smartboard control box mounted on the trailer as an information tool with pressure sensors incl., exclusively for overall axle load display. Display option can be selected via the control box or in the truck via the EBS air suspension system (truck manufacturer-dependent). * ?SP-Combination Package: Tool box with 45° corners made of galvanized sheet steel, additionally powder-coated in RAL 9006 white aluminum, on the fifth wheel platform, W=2,480 x H=500 mm with a folding lid on top, side doors and sloping corners. Incl. aluminum side walls that can be folded down to the fifth wheel platform (500 mm high), aluminum rear wall plugged in (150 mm high), aluminum side panels painted inside and out in RAL 9006 white aluminum. Incl. rear uprights, foldable and detachable, galvanized (without topcoat). Incl. bolted front structure. Length of front cross member to 5th wheel height 3,935 mm. Forward turning radius, without spare wheel, at 5th wheel height 2,450 mm or 2,750 mm, approx. 1,750 mm or approx. 1,480 mm. * 2 container locking mechanisms recessed into the front cross member. * 3 receiving shafts under the fifth wheel platform for storing optional aluminum ramps or wooden planks for covering the wheel recesses. * Folding/extendable outrigger (galvanized) and wooden planks for widening incl. (not on the rear slope), plank holder on the fifth wheel platform (the track width of the load may be a maximum of 2,500 mm). * Second LED position light on the warning package at the front and rear (double lighting), only in combination with the warning package. * 2 LED reversing lights on the rear of the trailer, switched with reverse gear (suitable for 12 V and 24 V), max. 2 additional lights in total. * 7-pole socket on the rear, wired for overhang lighting with tail light (58 R) and ground. Godpfxoy R Ipuj Apqoka * Rubber mat on the loading ramp on the left and right (approx. 860 mm long) 190 07644 rubber strip, on the inner plank of the one-piece ramps. * Central lubrication system fully automatic with pump (24 V), grease tank and integrated trailer control, without connection to the ramps (in the case of steering: incl. connection of the distributor of the fifth wheel platform). Note: Only possible with towing vehicles with a 24 V lighting system! Intermediate sale and errors are expressly reserved! Sale exclusively subject to our general terms and conditions (AGB). Important note - Important information: Despite careful checking of all details in our offer, errors may occur. Some of these are caused by transmission errors in the systems of the various platform providers. Therefore, we would like to point out that all information is provided without guarantee and does not c

Condition: used, maximum load weight: 13,860 kg, overall weight: 18,000 kg, axle configuration: 2 axles, first registration: 07/2022, loading space length: 6,770 mm, loading space width: 2,480 mm, loading space height: 600 mm, loading space volume: 10 m³, Equipment: ABS, ? galvanized chassis ? low-coupled ? 50 mm towing eye ? container lock ? 12 lashing rings per side ? rearview camera ? drum brakes ? Duomatic coupling ? ABS ? air suspension ? toolbox ? EBS Gkedpfx Aoxb Igljpqea ? support legs ? twin tires ? BPW axles All information is provided without guarantee / subject to prior sale.

Condition: used, maximum load weight: 13,860 kg, overall weight: 18,000 kg, axle configuration: 2 axles, first registration: 07/2022, loading space length: 6,770 mm, loading space width: 2,480 mm, loading space height: 600 mm, loading space volume: 10 m³, Equipment: ABS, ? galvanized chassis Gjdpfx Apexb Ig Seqjka ? low-coupled ? 50 mm towing eye ? container locking ? 12 lashing rings per side ? rear view camera ? drum brakes ? duomatic coupling ? ABS ? air suspension ? toolbox ? EBS ? support legs ? twin tires ? BPW axles All information subject to change / Prior sale reserved.

Condition: new, maximum load weight: 17,650 kg, overall weight: 24,000 kg, axle configuration: 3 axles, loading space length: 9,230 mm, loading space width: 2,480 mm, Year of construction: 2026, * TP 30.0 with 3 cable drum supports ----Braking system: * Wabco TEBS (electronic braking system) * Emergency release mechanism for spring brake cylinders * Drum brakes ----Axles: * 3 x 11 t Gigant axles ----Suspension: * Air suspension 17.5" with lifting and lowering device ----Drawbar: * Drawbar 1,800 mm long with 40 mm towing eye ----Electrics / Lighting: * Tire pressure monitoring with display capability in the truck dashboard via EBS signal -without truck-side installation- * 15-pin power connector * 2 additional LED reversing lights (activated via reverse gear) * LED lighting ----General attachments: * Aluminum air tank * Stainless steel side-mounted toolbox approx. 1,000 x 300 x 600 mm * Side underrun protection * Plastic quarter mudguards * Underride guard ----Flatbed: * Zurr-fix external frame, 45° angled with hole pattern for lashing equipment, lashing capacity per lashing point 2,000 kg at a spacing of 480 mm * Installation of 3,000 kg drop lashing brackets at approx. 600 mm intervals possible - delivery includes 12 x 3,000 kg lashing brackets per side * 5 pockets per side for stake posts 100 x 50 mm in the outer frame -stake posts not included in delivery- * 30 mm phenolic plywood flooring ----Drum supports: * 3 galvanized drum supports secured by container locks, with lateral forklift pockets, center/center 800 mm apart (pocket width 185 mm) * Maximum drum diameter 2,600 mm and maximum drum width 1,650 mm * Clear width between the support arms approx. 1,775 mm, with cross connection * Maximum drum weight per cable drum support 6,000 kg * Without drive and drum brake * Support arm with clamp lock for securing the drum shaft * Steel drum shaft 76 mm diameter with centering and rotatable ends * 2 stop rings * 2 centering cones made of polyamide * 4 x 3.2 t lashing eyes on the support arms for customer-side securing of the drum against rotation and unwinding ----Loading height: * Loaded approx. 1,040 mm ----Paintwork/Finish: * Chassis, turntable, drawbar, outer frame, underride guard hot-dip galvanized * Axles painted in a shade of black ----Information: * Technical upgrade to 30 t GVW possible Gsdpfx Apsx Nli Noqska * New vehicle with manufacturer’s warranty * Subject to errors and prior sale ----Delivery time: * Available from calendar week 51 / 2026

Condition: new, maximum load weight: 38,620 kg, overall weight: 50,000 kg, axle configuration: > 3 axles, Year of construction: 2026, T5 Profile 50.0: ----Brakes: * Wabco EBS (electronic braking system) * Emergency release device for spring brake cylinders * Drum brakes ----Axles: * 5 x 11 t Gigant axles * 3rd axle liftable (ride height +30 mm when lifted) * Last axle steerable (locking of trailing axle can be performed from the cab for maneuvering purposes, without installation on the truck side, as well as additionally by switch on the trailer); lock must be disengaged before driving on public roads Gedsxptn Dopfx Apqska * Forced lifting and forced lowering of the lift axle for maneuvering purposes (truck-side installation required) with speed-dependent control via the EBS electronics ----Suspension: * Air suspension, lifting and lowering system with RtR valve ----Drawbar: * Drawbar 1,500 mm long with 50 mm towing eye and manual height adjustment ----Electrics / Lighting: * Smartboard as infotool with pressure sensors to display total axle load per axle group * Tire pressure monitoring with display option in the truck via EBS signal (no truck-side installation required) * LED lighting system 12/24 V * Removable LED beacon (rear) ----General Attachments: * Mechanical warning sign package for 3 m total width * Toolbox made of galvanized steel sheet approx. 650 x 300 x 600 mm, mounted left side * Plastic wheel arches front axle and galvanized steel sheet mudguards on rear axle ----Low Loader Platform: * Turntable platform extension with 45° corners and 3 storage compartments with lockable folding lids (lids open to the rear) * Shortened low bed platform by 500 mm to 6,280 mm including extended stepped transition 500 mm forwards * Rubber covering on foldable frame, approach slope, and on the running surface of the low loader platform * Bamboo wood between the longitudinal beams in front of the excavator stick holder ----Load Securing (LaSi Package): * 2 x 6.4 t lashing rings at the front corners * 2 x 13.4 t UVV-compliant lashing points each at the front and rear side corners * 5 x 10 t UVV-compliant lashing rings per side (swiveling and lowerable, loadable in all directions) * 4 stake pockets per side, also 2 t lashing capability * 1 x 16 t UVV-compliant lashing point on the rear cross member ----Widening: * Extendable and foldable widening outriggers for 3 m overall width (board bracket holder under chassis, right side) ----Excavator Stick Holder: * Continuous excavator stick holder with reinforced profile from last axle to end beam, approx. L=2,350 x W=770 x H=270 mm, 2 pairs of 6.4 t UVV-compliant lashing rings on the sides of the stick holder ----Ramps: * Hydraulic folding ramp with double-acting hydraulics and extendable tip section, approx. 4,650 x 720 mm incl. load-holding valves and hydraulic side shift ----Rear Support: * Hydraulic rear support ----Hydraulics: * Hydraulic flow divider (for hydraulic pump outputs in the truck above 40 l/min, max. 140 l/min) ----Loading Height: * Loaded: 890 mm +/- 20 mm (via air suspension) ----Loading Area Dimensions: * Deck above turntable: 2,600 + 390 x 2,520 mm * Low bed area: 6,280 + 500 x 2,520 mm incl. 860 mm approach slope ----Paintwork: * Chassis, bogie, drawbar, extension consoles, access ramps hot-dip galvanized * Towing fork, axles, hydraulic axle supports, as well as air tanks painted in black ----Information: * New vehicle with manufacturer’s warranty * Subject to errors and prior sale ----Delivery Time: Immediately available*

Condition: new, maximum load weight: 38,620 kg, overall weight: 50,000 kg, axle configuration: > 3 axles, Year of construction: 2026, T5 Profile 50.0: ----Brakes: * Wabco EBS (electronic braking system) * Emergency release device for spring brake cylinders * Drum brakes ----Axles: * 5 x 11-ton Gigant axles * 3rd axle liftable (ride height +30 mm when axle is lifted) * Last axle self-steering (the steering lock for the trailing axle can be activated from the cab for maneuvering purposes without truck-side installation, as well as additionally by a switch on the trailer); the lock must be deactivated before driving on public roads * Forced lifting and lowering of the lift axle for maneuvering purposes (truck-side installation required) with speed-dependent activation via EBS electronics ----Suspension: * Air suspension with lifting and lowering system, equipped with RtR valve ----Drawbar: * Drawbar, 1,500 mm long with 50 mm towing eye, manual height adjustment ----Electrical / Lighting: * Smartboard info tool with pressure sensors for total axle load display per axle group * Tire pressure monitoring with display capability in the truck via EBS signal (no truck-side installation required) * LED lighting system 12/24 V * Removable LED beacon (rear) ----General Fittings: * Mechanical warning sign package for 3 m overall width * Toolbox, galvanized steel, approx. 650 x 300 x 600 mm, mounted left side * Front plastic fenders and galvanized steel rear mudguards ----Low-loader Area: * Front of turntable platform with 45° corners and 3 storage compartments with lockable flaps (flap opens to rear) * Shortened low-bed platform by 500 mm to 6,280 mm including extended stepped drop by 500 mm to the front * Rubber covering on folding frame, drive-on ramp and platform running surface * Bamboo wood insert between longitudinal members in front of excavator stick rest Gkedol Tihuepfx Apqsa ----Load Securing (Load Securing Package): * 2 x 6.4 t lashing rings at the front corners * On each side, front and rear corners, 2 x 13.4 t UVV-compliant lashing rings * 5 x 10 t UVV-compliant lashing rings per side (pivotable, retractable, loadable in all directions) * 4 side stake pockets per side with 2 t lashing capability * 1 x 16 t UVV lashing ring on rear crossmember ----Widening: * Extendable and foldable outriggers for up to 3 m overall width (plank holders under chassis on right side) ----Excavator Stick Rest: * Continuous excavator stick rest with reinforced profile from last axle to rear crossmember, approx. L=2,350 x W=770 x H=270 mm, 2 pairs of 6.4 t UVV lashing rings on the sides of stick rest ----Ramps: * Hydraulic folding ramp with dual-line hydraulics and adjustable ramp tip, approx. 4,650 x 720 mm, including load-holding valves and hydraulic side shift ----Rear Support: * Hydraulic rear support ----Hydraulic System: * Hydraulic flow divider (for hydraulic pump flow on truck from over 40 l/min up to 140 l/min max.) ----Loading Height: * Loaded: 890 mm +/- 20 mm by air suspension ----Loading Platform Dimensions: * Platform above fifth wheel: 2,600 + 390 x 2,520 mm * Low-bed platform: 6,280 + 500 x 2,520 mm, including 860 mm drive-on ramp ----Paintwork: * Chassis, turntable, drawbar, widening consoles, drive-on ramps – hot-dip galvanized * Drawbar, axles, hydraulic axle supports and air tanks painted in black ----Information: * New vehicle with manufacturer’s warranty * Subject to errors and prior sale ----Delivery Time: * Available immediately *

Condition: new, maximum load weight: 6,870 kg, overall weight: 9,900 kg, axle configuration: 1 axle, Year of construction: 2026, * KWH 9.9 ML: ----Brakes: * EBS braking system * Drum brake * Emergency release device for spring-loaded cylinders ----Axle: * BPW axle ----Suspension: * Parabolic springs ----Drawbar / Flange coupling: * Drawbar with 40 mm screw coupling (height-adjustable in mm) Gksdju I Iqfjpfx Apqsa ----Electrical system / Lighting: * 15-pin power connector * LED lighting * Flashing LED side marker lights * TPMS (tire pressure monitoring system) ----General components: * Front support winch * Spring-supported square tube supports at the rear with base plate, safety locking pins for various support heights * Closed steel sheet fenders with splash guard * Closed side impact protection, usable as an advertising area * Plastic toolbox with base insert (horizontal installation), approx. 500 x 350 x 400 mm ----Superstructure: * Swiveling cable drum superstructure, width between the drum arms 1,700 mm, with clamping device for securing the drum at the ends of the support arms and a locking mechanism for the cable drum superstructure on the chassis by means of a centrally arranged claw lock * Motorized hydraulic drum drive with oil motor * Valves and adjustable, rubber-coated drive rollers * Hydraulic speed controller and brake for drum drive * Steel drum shaft with 76 mm diameter, centering, and rotatable ends * 1 pair of centering cones made of polyamide, stepped ----Chassis: * Chassis made of torsionally rigid square tubes and cross members ----Pump - Unit: * Hydraulic pump unit with Loncin gasoline engine, including manual and electric starter * Fuel tank and manual starter * 13 HP with gear pump (150 bar) ----Tires: * 315/80 R 22.5 ----Unladen weight: * 2,690 kg unladen weight ----Paint: * Vehicle is hot-dip galvanized ----Information: * New vehicle with full manufacturer's warranty * Errors and prior sale subject to change ----Delivery time: * Available from approximately week 41/2026

Condition: new, maximum load weight: 6,870 kg, overall weight: 9,900 kg, axle configuration: 1 axle, Year of construction: 2026, * KWH 9.9 ML: ----Brakes: * EBS braking system * Drum brake * Emergency release device for spring accumulators ----Axle: * BPW axle ----Suspension: * Parabolic springs ----Drawbar / Flange coupling: * Drawbar with 40 mm threaded coupling (height-adjustable, in mm) ----Electrical System / Lighting: * 15-pin power connector * LED lighting * Flashing LED side marker lights * TPMS (Tire Pressure Monitoring System) ----General Components: * Front support jack * Spring-assisted square tube supports at the rear with base plate, safety locking pins for various support heights * Closed steel sheet fenders with splash guard * Closed side underrun protection, usable as an advertising space * Plastic toolbox with base insert (horizontal installation), approx. 500 x 350 x 400 mm ----Superstructure: * Swivelable cable drum superstructure, width between the drum arms 1,700 mm with locking mechanism to secure the drum at the ends of the support arms, as well as a locking mechanism for the cable drum superstructure with the chassis by means of a centrally arranged claw lock * Motor-hydraulic drum drive with oil motor * Valves and adjustable, rubber-coated drive rollers * Hydraulic speed controller and brake for drum drive * Steel drum shaft with 76 mm diameter, centering and rotatable ends Gksdpfxou I Iqrj Apqsa * 1 pair of centering cones made of polyamide, stepped ----Chassis: * Chassis made of torsion-resistant square tubes and cross members ----Pump Unit: * Hydraulic pump unit with Loncin gasoline engine, including manual and electric starter * Fuel tank and manual starter * 13 HP with gear pump (150 bar) ----Tires: * 315/80 R 22.5 ----Unladen Weight: * 2,690 kg unladen weight ----Paint Finish: * Vehicle is hot-dip galvanized ----Information: * New vehicle with full manufacturer's warranty * Errors and prior sale excepted ----Delivery Time: * Available from approximately week 41/2026

Condition: new, maximum load weight: 17,650 kg, overall weight: 24,000 kg, axle configuration: 3 axles, loading space length: 9,230 mm, loading space width: 2,480 mm, Year of construction: 2026, * TP 30.0 with 3 cable drum supports ----Braking system: * Wabco TEBS (electronic braking system) * Emergency release device for spring brake cylinders * Drum brakes ----Axles: * 3 x 11 t Gigant axles ----Suspension: * 17.5" air suspension with lifting and lowering facility Gjdpjx Nlkaefx Apqjka ----Drawbar: * Drawbar 1,800 mm long with 40 mm towing eye ----Electrics / Lighting: * Tyre pressure monitoring with display option in the truck dashboard via EBS signal (no truck-side installation required) * 15-pin power connector * 2 additional LED reversing lights (switched via reverse gear) * LED lighting ----General attachments: * Aluminium air tank * Stainless steel side toolbox approx. 1,000 x 300 x 600 mm * Side underrun protection * Plastic quarter mudguards * Rear underrun protection ----Platform: * Zurr-fix external frame, 45° angled, perforated for lashing devices, lashing capacity per lashing point 2,000 kg at a distance of 480 mm * Installation of 3,000 kg folding lashing rings at approx. 600 mm spacing possible - each side comes with 12 x 3,000 kg lashing rings supplied * Each side features 5 pockets for pipe stanchions 100 x 50 mm in the outer frame (pipe stanchions not included) * 30 mm phenolic resin-coated plywood floor ----Cable drum supports: * 3 galvanized cable drum supports, secured via container locks with side forklift pockets centre-to-centre 800 mm (pocket width 185 mm) * Max. drum diameter 2,600 mm and max. drum width 1,650 mm * Clear width between support arms approx. 1,775 mm, with cross-brace * Max. drum weight per support: 6,000 kg * Without drive or drum brake * Support arm with clamping lock for securing the drum shaft * Steel drum shaft, 76 mm diameter, with centering and rotating ends * 2 retaining collars * 2 centring cones made of polyamide * 4 x 3.2 t lashing eyes on the support arms to secure the drum against unintentional rotation and unwinding (provided by customer) ----Loading height: * approx. 1,040 mm loaded ----Paintwork/finish: * Chassis, turntable, drawbar, outer frame, and underrun protection hot-dip galvanized * Axles painted in black

Condition: new, maximum load weight: 20,500 kg, overall weight: 27,000 kg, axle configuration: 3 axles, loading space length: 7,000 mm, loading space width: 2,470 mm, Year of construction: 2026, * ETÜ-TR 27.0 Platform: * EBS (electronic braking system) * Emergency release device for spring-loaded brake cylinders * Drum brakes * 3 x 9 t BPW Eco axles * Air suspension with lift and lower function including RTR feature * 1st axle liftable * Last axle as trailing steering axle with electro-pneumatic steering lock activated via reverse gear PIN (lockout of the trailing axle from driver's cab for maneuvering - no truck-side installation required - assigned to PIN 10 of the 15-pin connector; for maneuvering purposes only, not for public road use) Gkodpfxor Dpz Aj Apqja * SmartBoard control box as infotool with pressure sensors for total axle load display * Tire pressure monitoring with display option in the truck via EBS signal (no truck-side installation required) * Fixed center drawbar with 50 mm flanged towing eye (900 mm when loaded, height adjustable at the head plate) * Mechanical support winch in front, mechanical swing-down supports at the rear of chassis * Mechanically adjustable warning sign package front and rear * Toolbox made of galvanized steel sheet - black powder coated - approx. 650 x 300 x 600 mm, mounted on the right side * Hydraulic flow divider * Continuous sidewalls (without center stanchion) up to the approach ramp * Folding rear stanchions * Steel rear wall inserted in front of rear stanchions * 15-pin power connector * LED taillights * LED revolving beacon (removable), incl. bracket and installation * 2 x LED reversing lights at the rear of vehicle (activated by reverse gear) * Flashing LED side marker lights * 60 mm larch/douglas fir flooring * 400 mm plug-in steel front wall * Perforated outer frame, approx. 45° chamfered with provisions for mounting 3 t folding lashing brackets * 1 x 10 t lashing ring in each corner; additionally, 2 x 10 t and 3 x 6.3 t lashing rings on each side * Various holes in front and rear cross-members for 1.2 t lashing options * Hydraulic one-piece loading ramps approx. 3,000 x 720 mm, mechanically adjustable sideways * 4-way hydraulic control block for optional retrofitting of hydraulic ramp displacement * Chassis, drawbar, front wall, mechanical rear supports, loading ramps, and tailgate fully hot-dip galvanized * Axles, air tanks, flanged towing eye, and front support winch painted in black * Hydraulic flow divider in trailer (for hydraulic pump capacity in truck from over 40 l/min up to 120 l/min) * New vehicle with manufacturer’s warranty * Errors and interim sales excepted * Immediately available ex Egestorf

Condition: new, maximum load weight: 17,650 kg, overall weight: 24,000 kg, axle configuration: 3 axles, loading space length: 9,230 mm, loading space width: 2,480 mm, Year of construction: 2026, * TP 30.0 with 3 cable drum supports ----Braking System: * Wabco TEBS (electronic braking system) * Emergency release device for spring-loaded cylinders * Drum brakes ----Axle: * 3 x 11 t Gigant axles ----Suspension: * 17.5" air suspension with lifting and lowering system ----Drawbar: * Drawbar 1,800 mm long with 40 mm towing eye ----Electrics / Lighting: * Tire pressure monitoring with display option in the truck display via EBS signal (no installation required on truck side) * 15-pin power plug * 2 additional LED reversing lights (switched via reverse gear) * LED lighting ----General Attachments: * Aluminum air tank * Stainless steel toolbox on the side approx. 1,000 x 300 x 600 mm * Side underride protection * Plastic quarter mudguards * Underrun protection ----Platform: * Zurr-fix external frame, bend 45°, with perforation for lashing equipment, lashing force per point 2,000 kg at 480 mm intervals * Option to install 3,000 kg drop lashing brackets at approx. 600 mm intervals – includes 12 pcs. 3,000 kg lashing brackets per side * Each side with 5 pockets for pipe stanchions 100 x 50 mm in the outer frame (stanchions not included) * 30 mm phenolic plywood floor ----Drum Supports: * 3 galvanized drum supports, secured with container locks and side forklift pockets, center-to-center 800 mm (pocket width 185 mm) * Max. drum diameter 2,600 mm, max. drum width 1,650 mm * Clear width between the support arms approx. 1,775 mm, with crossbar * Drum weight per support: 6,000 kg * Without drive and drum brake * Support arm with tension lock for drum shaft securing * Steel drum shaft, 76 mm diameter, with centering and rotating ends Gkjdpfx Ajx Nlkgjpqea * 2 set collars * 2 centering cones made of polyamide * 4 pcs. 3.2 t lashing eyes on the support arms for customer-side securing of the drum against rotation and unspooling ----Loading height: * Approx. 1,040 mm loaded ----Painting: * Chassis, turntable, drawbar, external frame, underrun protection hot-dip galvanized * Axles painted black ----Information: * Technical GVWR upgrade to 30 t possible * New vehicle with manufacturer’s warranty * Errors and prior sale excepted ----Delivery time: * Available from approx. week 51 / 2026

Condition: new, maximum load weight: 20,500 kg, overall weight: 27,000 kg, axle configuration: 3 axles, loading space length: 7,000 mm, loading space width: 2,470 mm, Year of construction: 2026, * ETÜ-TR 27.0 Platform: * EBS (Electronic Braking System) * Emergency release device for spring brake cylinders * Drum brakes * 3 x 9 t BPW Eco axles * Air suspension with lifting and lowering system, with RTR function * 1st axle liftable * Last axle as follower steering axle with electro-pneumatic steering lock via PIN reverse gear (locking of the follower axle from the tractor unit for maneuvering purposes - without truck-side installation - assigned to PIN 10 in the 15-pin connector, for maneuvering purposes only, not for use in public road traffic) * SmartBoard control unit as an infotool, with pressure sensors for total axle load display * Tire pressure monitoring with display option in the truck via EBS signal, no truck-side installation required * Fixed central drawbar with 50 mm flanged towing eye (loaded 900 mm, height adjustment at the head board) * Mechanical landing gear at the front, mechanical swing-down supports at the rear of the chassis * Hydraulic flow divider * Continuous side walls (without center posts) up to the run-on ramp * Rear stanchions foldable * Steel rear wall inserted in front of the rear stanchions * Mechanically adjustable warning sign package at front and rear * Tool boxes made of galvanized sheet steel - black powder coated - approx. 650 x 300 x 600 mm, mounted right side * 15-pin power connector * LED tail lights * Detachable LED rotating beacon incl. bracket and installation * 2 x LED reverse lights at vehicle rear (activated via reverse gear) * Flashing LED side marker lights * 60 mm larch / douglas fir wood floor * 400 mm plug-in steel front wall * Perforated outer frame, approx. 45° angled, with provisions for mounting 3 t folding lashing brackets * In each corner 1 x 10 t lashing ring, as well as 2 x 10 t and 3 x 6.3 t lashing rings per side additionally * Various holes in the front and rear cross members for 1.2 t lashing options * Hydraulic one-piece drive-on ramps, approx. 3,000 x 720 mm, mechanically adjustable sideways * 4-way hydraulic control block for possible retrofit of hydraulic ramp shifting * Chassis, drawbar, front wall, rear manual supports, and drive-on ramps hot-dip galvanized * Axles, air tanks, flanged drawbar eye, and front mechanical landing gear coated in black Gkodpfxsr Dpzxs Apqea * Hydraulic flow divider in the trailer (for hydraulic pump output from 40 l to 120 l/min in the truck) * New vehicle with manufacturer’s warranty * Errors and prior sale excepted * Immediately available from Egestorf

Condition: used, empty load weight: 11,000 kg, maximum load weight: 39,000 kg, overall weight: 50,000 kg, axle configuration: > 3 axles, first registration: 06/2015, next inspection (TÜV): 04/2027, loading space length: 9,250 mm, loading space width: 2,720 mm, loading space height: 950 mm, suspension: air, tire size: 235/75R17.5, color: blue, mileage: 1,001 km, gearing type: other, driver cabin: other, Equipment: ABS, Vehicle location: Bovenden, 5 axles, turntable, air suspension, last axle with trailing steering, ABS (anti-lock braking system), lashing points, 2-part loading ramps, hydraulic ramps, rear supports, side aluminum fender, twin tires. Godoy U N Nwopfx Apqjka Superstructure: 5-axle low-bed trailer with hydraulic 2-part loading ramps, 5x 10t Gigant axles, drum brakes, last axle with trailing steering! The first 3 axles have new brake pads! ACCESSORY INFORMATION WITHOUT GUARANTEE, subject to changes, prior sale, and errors!

Condition: used, maximum load weight: 6,800 kg, overall weight: 9,900 kg, axle configuration: 1 axle, first registration: 06/2026, Year of construction: 2026, Müller-Mitteltal KWH 9,9 ML Cable Transport Trailer with Diesel Engine * KWH 9,9 ML * Drum brake braking system EBS 2S/2M * BPW axles * Leaf spring suspension, parabolic spring * Spring-supported square tube supports at the rear with base plate and safety locking pins for various support heights * Drawbar with 40 mm or 50 mm screw-on drawbar eye (height-adjustable, in mm) * Bracket for additional drawbar, mounted on the side of the drawbar, on the right side in the direction of travel * Chassis made of torsionally rigid square tubes and cross members * Plastic toolbox * LED lighting * Swiveling cable drum assembly consisting of a base frame, bearings, and drum support arms * Support arm ends with clamping device for securing the drum shaft * Locking of the swiveling cable drum assembly to the chassis via a centrally located claw lock * Steel drum shaft, 76 mm diameter, with centering and rotatable ends * With a drum diameter of 3,000 mm, a maximum drum width of 1,650 mm is possible * Motor-hydraulic pull and push cylinders with load-holding valve * Control valve with automatic zero position and pressure relief valve * Connectors, hoses, and pipes of the hydraulic system in NW 13 * Required oil consumption approx. 10 liters * Drum drive, motor-hydraulic, with oil motor, valves, and rubber-coated drive rollers (adjustable). Hydraulic speed regulator and brake for drum drive Godsy R Ipnepfx Apqjka * Hydraulic pump unit with diesel engine and manual starter, 6.5 HP with gear pump (150 bar) * Pressure supply by switching the connection lines, either via truck hydraulics or the pump unit * Cover as weather protection, hot-dip galvanized without topcoat * Tires 315/80 R22.5 Subject to prior sale and errors! Sale exclusively subject to our general terms and conditions. Important note – Important information: Despite careful checking of all details in our offer, errors may occur. Some of these are caused by transmission errors in the systems of the various platform providers. Therefore, we would like to point out that all information is provided without guarantee and does not constitute a legal claim. Legal: This sales advertisement does not constitute an offer within the meaning of §145 BGB. Rather, it provides information for the initiation of a contract. The information provided here is without guarantee and therefore does not constitute guaranteed characteristics.

Condition: used, axle configuration: 2 axles, loading space volume: 10 m³, total length: 7,500 mm, total width: 2,550 mm, total height: 4,000 mm, Year of construction: 2012, Applicable material: Concrete Empty weight: 6.530 kg Carrying capacity: 25.470 kg Gjdpfex Utq Ssx Apqeka GVW: 32.000 kg Tyre size on axle 1: 385/65 R22,5 Brake type on axle 1: drum Tyre size on axle 2: 385/65 R22,5 Tyre size on axle rear: 385/65 R22,5 Concrete mixer brand: Liebherr

Condition: used, empty load weight: 3,590 kg, maximum load weight: 10,810 kg, overall weight: 14,400 kg, axle configuration: 2 axles, first registration: 06/2020, loading space width: 5,040 mm, loading space height: 2,420 mm, suspension: steel, tire size: 285/70R19,5 150J, color: other, gearing type: other, front tire size: 285/70R19,5 150J, rear tire size: 285/70R19,5 150J, driver cabin: other, emission class: none, Equipment: ABS, compressed air brake, front for through-loading, lashing eyes, surcharge for ramps: 1,000 EUR, subject to printing errors, errors and changes, sample images, more details at: ! Gsdpfszt I Sxox Apqska

Condition: new, suspension: other, color: other, gearing type: other, driver cabin: other, emission class: none, fuel: biodiesel, Storage compartment for aluminum ramps, price per storage compartment, length approx. 2.48 m, width approx. 1 m, height approx. 27 cm, , --  Misprints, errors and changes reserved, sample images --, More information at: !, More details: ! Godpfx Aoztd Nyjpqoka

Condition: used, empty load weight: 8,850 kg, maximum load weight: 31,150 kg, overall weight: 40,000 kg, axle configuration: > 3 axles, first registration: 08/2019, suspension: steel, tire size: 235 / 75 R 17,5, color: other, gearing type: other, front tire size: 235 / 75 R 17,5, rear tire size: 235 / 75 R 17,5, driver cabin: other, emission class: none, fuel: biodiesel, Equipment: ABS, compressed air brake, Total loading platform length approx. 9,500 mm, lowbed loading platform length approx. 7,360 mm, loading height approx. 910 mm, 14 pairs of lashing eyes. Vehicle is offered on behalf of the customer. -- Subject to errors, misprints, and changes. Sample images -- More data at: !, More Details: ! Gsdpfxezr Uh De Apqoka

Condition: used, empty load weight: 7,340 kg, maximum load weight: 22,660 kg, overall weight: 30,000 kg, axle configuration: 3 axles, first registration: 05/2012, loading space length: 9,200 mm, suspension: steel, tire size: 235/75 R 17,5, color: other, gearing type: other, front tire size: 235/75 R 17,5, rear tire size: 235/75 R 17,5, driver cabin: other, emission class: none, Equipment: ABS, compressed air brake, Loading area length approx. 9,200 mm, loading height approx. 900 mm, 16 x lashing eyes, , Vehicle is sold on order , , , -- Subject to misprints, errors and alterations, sample pictures --, More data under: !, More Details: ! Gsdpfjzr Uihex Apqeka