Used Müller-Mitteltal Semitrailers With Work Platform for sale (268)

Condition: new, maximum load weight: 6,870 kg, overall weight: 9,900 kg, axle configuration: 1 axle, Year of construction: 2026, * KWH 9.9 ML: ----Brakes: * EBS braking system * Drum brake * Emergency release device for spring-loaded cylinders ----Axle: * BPW axle ----Suspension: * Parabolic springs Bwodpfxsu I Iqxo Ak Tjt ----Drawbar / Flange drawbar: * Drawbar with 40 mm threaded drawbar coupling (height-adjustable in mm) ----Electrical system / Lighting: * 15-pole power plug * LED lighting * Flashing LED side marker lights * TPMS tire pressure monitoring system ----General components: * Front support jack * Spring-supported square tube supports at the rear with base plate, safety locking pins for different support heights * Closed mudguards made of sheet steel with splash protection * Closed side impact protection, can be used as an advertising space * Plastic tool box with base insert (horizontal installation) approx. 500 x 350 x 400 mm ----Superstructure: * Swiveling cable drum superstructure, width between the drum arms 1,700 mm with a clamping device to secure the drum at the ends of the support arms, and a locking mechanism for the cable drum superstructure with the chassis using a centrally arranged claw lock * Motor-hydraulic drum drive with oil motor * Valves and sliding, rubber-coated drive rollers * Hydraulic speed regulator and brake for drum drive * Steel drum shaft with 76 mm diameter, centering, and rotatable ends * 1 pair of centering cones made of polyamide, stepped ----Chassis: * Chassis made of torsion-resistant square tubes and cross members ----Pump unit: * Hydraulic pump unit with diesel engine * Fuel tank and manual starter * 6.5 HP with gear pump (150 bar) ----Tires: * 315/80 R 22.5 ----Unladen weight: * 2,690 kg unladen weight ----Painting: * Vehicle is hot-dip galvanized ----Information: * New vehicle with full manufacturer's warranty * Errors and prior sale excepted ----Delivery time: * Immediately available from Egestorf

Condition: new, maximum load weight: 6,900 kg, overall weight: 9,900 kg, axle configuration: 1 axle, Year of construction: 2026, * KWH 9.9 ML: ----Brakes: * EBS braking system * Drum brake ----Axle: * BPW axle ----Suspension: * Parabolic springs ----Electrical System / Lighting: * TPMS (Tire Pressure Monitoring System) * 15-pin electrical connector Bwsdsxyniwepfx Ak Tjt * LED lighting * Flashing LED side marker lights ----Drawbar / Flange Coupling: * Drawbar with 40 mm screw coupling (height adjustable in mm) ----General Components: * Front support jack * Spring-supported square tube supports at the rear with base plate, safety locking pins for different support heights * Closed steel sheet mudguards with splash protection * Closed side impact protection, usable as an advertising area * Plastic toolbox with floor insert (horizontal installation), approx. 500 x 350 x 400 mm ----Superstructure: * Swiveling cable drum superstructure, width between the drum arms 1,700 mm, with tensioning closure for securing the drum at the ends of the support arms, as well as a locking mechanism for the cable drum superstructure with the chassis via a centrally arranged claw lock * Motor-hydraulic drum drive with oil motor * Valves and adjustable rubber-coated drive rollers * Hydraulic speed controller and brake for drum drive * Steel drum shaft with 76 mm diameter, with centering and rotatable ends * 1 pair of centering cones made of polyamide, stepped arrangement * Preparation of steel structure and hydraulics for retrofitting a separate motor ----Chassis: * Chassis made of torsion-resistant square tubes and cross members ----Hydraulics: * Hydraulic line for supply and return ----Tires: * 315/80 R 22.5 tires ----Painting: * Vehicle is hot-dip galvanized ----Information: * 2,690 kg unladen weight * New vehicle with full manufacturer warranty * Errors and prior sale excepted ----Delivery time: * Available for immediate delivery from Egestorf

Condition: new, maximum load weight: 29,850 kg, overall weight: 38,000 kg, axle configuration: 2 axles, loading space length: 8,000 mm, loading space width: 2,520 mm, Year of construction: 2026, TS 2 ML ----Brakes: * EBS-E (electronic braking system) * Emergency release device for spring brake cylinders * Drum brakes ----Axles: * 2 x 10 t axles * Rear axle as a trailing steering axle with electro-pneumatic steering lock activated by PIN when reverse gear is selected * Additional lock for the trailing axle, operated from the driver's cab for maneuvering purposes – no truck-side installation required – assigned to PIN 10. The lock must be deactivated before driving on public roads ----Suspension: * Air suspension with lifting and lowering function as well as RtR (Ride to Recover) function ----Electrics / Lighting: * Tire pressure monitoring system with display option in the truck dashboard via EBS signal – no truck-side installation required * LED tail lights 12 / 24 V * Flashing side marker lights * LED reversing lights switched via reverse gear * SmartBoard installed as info tool with pressure sensors exclusively for total axle load display * 7-pin socket at the rear for overlength lighting * Removable LED rotating beacon at the rear ----General attachments: * Aluminum air tanks * Mechanical crank landing legs * Galvanized steel mudguards * Swivel arm as a carrier for connection lines mounted in front of the front panel ----Warning package: * Mechanically adjustable warning sign package ----Low-bed platform: * 50 mm flooring made of larch / Douglas fir instead of spruce / fir * Rear slope – 700 mm long – on the gooseneck deck to the low-bed with checker plate covering, and perforated strip at the end for attaching aluminum approach ramps * Tread plate cover over wheels * SP-Combo package: toolbox with 45° corners, made of galvanized sheet steel, additionally powder-coated in RAL 9006 white aluminum, mounted on the platform approx. 2,480 x 500 mm * Flip-top lid as well as side doors in the slanted corners * Folding aluminum side walls 500 mm high on the platform, incl. folding and removable rear stanchions * Plug-in aluminum rear wall 150 mm high * Second kingpin position * Preparation for container lock * Preparation for 3 insert pockets in the inclined ramp from low-bed to gooseneck * Preparation for retrofitting folding outriggers for 3 m widening by welding the mounting brackets into the outer frame ----Load securing: Fifth wheel platform: * In the front corners and at the front, 50 mm holes for 1.2 t lashing force per hole * 2 x 16.5 t lashing rings recessed in the floor on the side at the approach slope Bedpfx Aksykx I Tj Tswt * Perforated and bent 45° outer frame with hole pattern for lashing equipment (2 t lashing points every 480 mm) * On each side: 2 x 6.3 t retractable lashing rings recessed into the outer frame Low-bed platform: * 2 x 16.5 t lashing rings recessed centrally directly in front of the approach slope to the gooseneck * On each side: 3 pairs of 13.5 t and 5 pairs of 10 t retractable lashing rings recessed into the outer frame * On each side: 4 stanchion pockets recessed into the outer frame * Profifix lashing rail centered in the longitudinal axis (lashing point 3 t per securing circle) ----Excavator arm trough: * From the end of the last rigid axle to the end cross member B = 770 mm, D = 270 mm (on each side 2 x 6.4 t lashing rings for the excavator arm trough, permanently welded) ----Ramp: * Hydraulic one-piece "ALLTEC" aluminum approach ramps approx. 3,200 x 750 mm * Load capacity 13 t per ramp (26 t per pair) * Hydraulic ramp shifting on sliding pipe of the ramp shaft ----Hydraulics: * Hydraulic flow

Condition: used, axle configuration: 3 axles, Year of construction: 2015, = Additional Options and Accessories = - Air suspension, rear - Air suspension, front - Central lubrication system = Notes = WE SPEAK RUSSIAN - Yuriy mobile: 3-axle, low-bed semi-trailer, drop-deck design. Fifth wheel platform approx. 3,900 x 2,550 mm with aluminum side walls, low-bed platform approx. 9,050 x 2,550 mm, 4 wheel recesses with extension sections, recesses at the front approx. 390 mm, at the rear approx. 290 mm, wheelbase center-to-center approx. 3,100 mm, excavator arm rest. Loading height approx. 900 mm. 34 lashing points, foldable widening sections to 3,000 mm, warning package for overwidth loads. Hydraulic ramps, two-part, approx. 4,300 x 720 mm with rubber coating, hydraulically adjustable, BPW axles, 3 axles hydraulically steered, including remote control, EBS, air suspension, lift axle. Permissible total weight 48,000 kg, fifth wheel load 18,000 kg, payload 35,350 kg. Fifth wheel pin 2 inches, fifth wheel height approx. 1,250 mm. Toolbox on the fifth wheel platform. Tires 235-75R17.5. 2-line air, hydraulic pump unit. Central lubrication. Paint finish MB 5361, gentian blue. Valid MOT until 07-2027. = Further Information = Unladen weight: 12,650 kg Payload: 35,350 kg Bjdjzq Rg Hepfx Ak Tswt GVW: 48,000 kg Tires, front: 235-75R17.5 Tires, rear: 235-75R17.5 Country of origin: DE Please contact Jan-Marc Schwickert for further information.

Condition: new, maximum load weight: 23,210 kg, overall weight: 30,000 kg, axle configuration: 3 axles, Year of construction: 2026, Equipment: ABS, * T 3: * EBS braking system * Emergency release device for spring accumulators * Drum brakes * 3 x 11-ton BPW Eco axles * Parabolic springs * Mechanical axle compensation at the rear * Side impact protection * Swivel supports at the rear of the chassis frame * Mechanically adjustable warning sign panels at the front and rear * Front axle with closed plastic mudguards and rear axle with straight, galvanized steel splash guards, each with splash protection * Reflective contour strip on the sides and at the rear * Folding cover (hot-dip galvanized) for the toolbox in the turntable platform * Toolbox made of galvanized steel sheet, approx. 650 x 300 x 600 mm - black powder-coated - located on the side under the chassis * 15-pin electrical connector * LED lighting 12 / 24 V * LED rotating beacon (removable) at the rear * Drawbar with 40 mm towing eye and height adjustment via tension spring and locking clamp * 4 lashing pockets on each side (but no lashing bars included) with simultaneous lashing capability * Lashing package consisting of: 2 lashing eyes (6.4 tons) at the front left and right on the main frame of the turntable platform * 5 pairs of UVV lashing rings, swivel and lowerable * Load-bearing in all directions and embedded in the outer frame in the corners, 13.4 tons, otherwise 10 tons * 6 pairs of mechanical folding outriggers for a total width of 3 meters (but not in the rear slope) Bedstplwfopfx Ak Tswt * Extension boards under the loading platform, stored in a storage compartment * Excavator arm support over the rear axle up to the end beam, approx. 2,100 mm long (2 pairs of 6.4-ton lashing rings on the side in the excavator arm support) * Hydraulic folding ramps (approx. 4,650 x 720 mm) with hydraulically extendable front section and load holding check valves, hydraulic lateral ramp adjustment * Hydraulic flow divider in the trailer (for hydraulic pump output in the truck of more than 40 liters up to a maximum of 140 liters / min.), dual-line hydraulics * Loading area above the slewing ring: approx. 1,960 x 2,520 mm * Rear loading area: approx. 6,500 x 2,520 mm (incl. 860 mm access ramp) * Loading height when loaded approx. 860 mm +/- 30 mm compensation unit * Chassis, turntable, folding outriggers, rear support legs and access ramps hot-dip galvanized. * Axles, springs, drawbar, air tank, etc. painted in a black tone. * New vehicle with manufacturer's warranty * Errors and prior sale excepted * Available for immediate delivery from Egestorf

Condition: new, maximum load weight: 23,210 kg, overall weight: 30,000 kg, axle configuration: 3 axles, Year of construction: 2026, Equipment: ABS, * T 3: * EBS braking system * Emergency release device for spring accumulators * Drum brakes * 3 x 11 tons BPW Eco axles Bwedpfeq Dyv Ijx Ak Tot * Parabolic springs * Mechanical axle compensation at the rear * Side impact protection * Swivel supports at the rear on the chassis frame * Mechanically adjustable warning sign packages at the front and rear * Front axle with closed plastic fenders and rear axle with straight, galvanized steel splash guards, each with splash protection * Reflective contour strip on the sides and rear * Hinged cover (hot-dip galvanized) for the toolbox in the turntable platform * Toolbox made of galvanized sheet steel, approx. 650 x 300 x 600 mm - black powder coated - mounted on the side under the chassis * 15-pole power connector * LED lighting 12 / 24 V * LED rotating beacon (removable) at the rear * Drawbar with 40 mm towing eye and height adjustment via coil spring and tension lock * 4 lashing pockets on each side (but no lashing bars included) with simultaneous lashing capability * La-Si package consisting of: 2 lashing eyes (6.4 tons) at the front left and right on the main frame of the turntable platform * 5 pairs of UVV lashing rings, swivel and lowerable * Loadable in all directions and embedded in the outer frame in the corners, 13.4 tons, otherwise 10 tons * 6 pairs of mechanical folding outriggers for a total width of 3 m (but not in the rear slope) * Extension boards under the loading area, stored in a storage compartment * Excavator arm support over the rear axle up to the end member, approx. 2,100 mm long (2 pairs of 6.4 tons lashing rings on the side in the excavator arm support) * Hydraulic folding ramps (approx. 4,650 x 720 mm) with hydraulically extendable front section and load-holding check valves, hydraulic side ramp adjustment * Hydraulic flow divider in the trailer (for hydraulic pump output in the truck of over 40 liters up to max. 140 liters / min), dual-line hydraulics * Loading area above the slewing ring: approx. 1,960 x 2,520 mm * Rear loading area: approx. 6,500 x 2,520 mm (incl. 860 mm approach ramp) * Loading height when loaded approx. 860 mm +/- 30 mm compensating unit * Chassis, turntable, folding outriggers, rear support legs and loading ramps hot-dip galvanized. * Axles, springs, drawbar, air tank, etc. painted in a black tone * New vehicle with manufacturer's warranty * Errors and prior sale are subject to change * Available for immediate delivery from Egestorf

Condition: used, maximum load weight: 15,100 kg, overall weight: 20,000 kg, axle configuration: 2 axles, first registration: 03/1987, loading space length: 8,650 mm, loading space width: 2,480 mm, ? Mechanical ramps ? Loading height: approx. 910 mm ? Spare wheel holder ? 40 mm towing eye ? Beacon ? Drum brakes ? Leaf suspension ? 1 x toolbox ? Twin tires ? SAF axles Bwedpfxoyw Egwe Ak Tjt All information without guarantee / Subject to prior sale.

Condition: new, maximum load weight: 15,970 kg, overall weight: 21,000 kg, axle configuration: 2 axles, loading space length: 7,000 mm, loading space width: 2,470 mm, loading space height: 400 mm, Year of construction: 2026, ETÜ-TA-R 21.0: ----Brakes: * Wabco EBS-E (electronic braking system) * Emergency release system for spring brake cylinders * Drum brakes ----Axle: * 2 x 11 ton Gigant axles ----Suspension: * Air suspension with lifting and lowering system ----Drawbar / Flange coupling: * Drawbar with 50 mm flange coupling and height-adjustable drawbar ----Lighting / Electrical System: * 15-pin power connector * LED lights 12/24 V * TPMS (Tire Pressure Monitoring System) ----General Components: * Jost support leg at the front * Outboard folding supports at the rear * Plastic tool box approx. 750 x 350 x 300 mm on the right side * Side underrun protection * Plastic quarter fenders ----Low-Loader Platform: * In front of the headboard and rear slope, provision for retrofitting container locking mechanisms for transporting 20" containers * Design for 21 tons GVW with reinforced frame and reinforced axles * Reinforcement package for drilling rig transport on the chassis * 50 mm hardwood floor in a clamped design * In front of the headboard, provision for retrofitting container locking mechanisms * Bolted headboard made of smooth sheet metal Bjdpjl Tihxsfx Ak Towt * Divided side walls made of steel sheet - trapezoid profile - foldable with folding mechanism in the middle * Steel rear wall can be slid between the ramps - bracket for storage when not in use inside in front of the headboard * Rear supports bolted ----Load Securing: * Perforated outer frame approx. 45 degrees angled, with 2 tons lashing force every 480 mm * Installation of 3 tons tie-down brackets every 600 mm possible * Profifix lashing rail in the longitudinal axis in the middle for lashing up to LC 3000 daN * In the corners at the front and rear, 1 x 10 tons lashing each * Lasi package with 2 x 8 tons lashing points each on the sides, recessed in the outer frame, various holes in the front and end beams for 1.2 tons lashing ----Ramps: * One-piece mechanical grating ramps with spring mechanism for single-person operation approx. 3,000 x 620 mm (can be moved together to 20 mm) * Approach slope at the rear approx. 860 mm chassis ----Loading Heights: * Unloaded approx. 940 mm * Loaded approx. 910 mm ----Wheelbase / Tires: * 1,810 mm * Tires: 235/75R17.5 ----Paint: * Painting of the side walls in RAL - 9010 pure white * Drawbar, headboard, rear flap, folding supports and ramps hot-dip galvanized * Axles, springs, air tanks and support leg painted in a black tone ----Information: * New vehicle with manufacturer's warranty * Errors and prior sale excepted ----Delivery Time: * Available immediately from Egestorf

Condition: used, first registration: 11/2006, Year of construction: 2006, MÜLLER - MITTELTAL T4 Kompakt Turntable - Low-loader with air suspension and wheel recesses - 4 x air-suspended GIGANT axles - air suspension - 4 x wheel recesses - mechanical loading ramps - 2 foldable rear supports - extendable warning panels - ABS - MICHELIN tyres: 235/75 R 17.5 - heavy-duty version: 40,000 kg GVW - unladen weight: 8,400 kg - overall length: 11,750 mm - 50 mm towing eye Particularly suitable for transporting lime milling machines! - German trailer - General inspection / safety test available on request and at extra cost! Bwedpfxswmpbde Ak Tet Subject to prior sale and errors!

Condition: new, Year of construction: 2026, Cable reel transport trailer. Permissible total weight 9,900 kg, payload 7,380 kg. Hydraulic lifting and lowering of the cable reel from the towing vehicle or by a 4-stroke gasoline engine, protective cover, reel drive hydraulically with rubber-coated drive rollers, reel diameter 800-3,000 mm, reel width up to 1,650 mm, centering cones for cable reels. Two-speed support winch at the front, extendable rear support. BPW axle, EBS, parabolic suspension, tires 315-80R22.5, tire pressure monitoring. Tow hitch 40 mm, height-adjustable, 2-line air, lighting 12+24 V LED. Tool box. Vehicle completely hot-dip galvanized. New vehicle including factory warranty. = Further information = Unladen weight: 2,520 kg Payload: 7,380 kg GVW: 9,900 kg Condition of rear tires: 100 Bodpfszp Dnbex Ak Towt Front tires: 315-80R22.5 Rear tires: 315-80R22.5 Country of manufacture: DE Please contact Jan-Marc Schwickert for further information.

Condition: used, first registration: 06/2011, total width: 25,500 mm,

Condition: used, maximum load weight: 7,700 kg, overall weight: 10,500 kg, axle configuration: 2 axles, first registration: 08/1979, next inspection (TÜV): 07/2027, loading space length: 5,000 mm, loading space width: 2,420 mm, loading space height: 600 mm, total width: 2,350 mm, total height: 1,650 mm, Equipment: tail-lift, Müller MItteltal KA-TA * Tandem three-way tipper * Heavy-duty trailer * First registration: 08/29/1979 * Next inspection: 07/2027 * Gross vehicle weight: 10,500 kg * Tare weight: 2,800 kg * Payload: 7,700 kg Bwodozn E Uyjpfx Ak Tet * Overall dimensions: 6,200 mm x 2,350 mm x 1,650 mm * Internal dimensions: 4,500 mm x 2,200 mm x 500 mm * Side walls painted * Air brake system * Steel side walls, rear section can be folded down, removable, and pivoting * 2 supports at the rear * Support wheel ATTENTION!!!!! PLEASE READ CAREFULLY!!!!! We expressly reserve the right to sell the item in the meantime, as we are also offering it on other platforms. We strongly recommend an inspection and assessment to ensure that the buyer does not have any incorrect expectations regarding the condition and suitability of the item. Inspections and assessments are possible and expressly welcome at any time by prior appointment!!! Illustrations are similar and may include optional accessories that incur an additional charge. The specified internal dimensions are approximate. Information without guarantee! Errors and omissions excepted! TRADE-INS POSSIBLE FOR ALMOST ANYTHING!!! EXCHANGE DEALS AND PAYMENT PLANS POSSIBLE!!! Exhibition grounds: 58285 Gevelsberg, Am Sinnerhoop 17 Opening hours: Monday - Friday 8:30 a.m. to 5:00 p.m., Saturday 8:30 a.m. to 2:00 p.m. Over 500 trailers in stock!!! Pegasus Anhänger GmbH Am Sinnerhoop 17 58285 Gevelsberg Tel.: Fax:

Condition: used, maximum load weight: 29,750 kg, overall weight: 40,000 kg, axle configuration: > 3 axles, first registration: 03/2010, next inspection (TÜV): 05/2026, Dimensions - Length: 11,750 mm Unladen weight: 10,250 kg Axle load: 2 x 10,000 kg Load length over turntable: 2,400 mm incl. 350 mm bevel Load length: 7,700 mm incl. 900 mm bevel Loading height: 880 mm Width: 2,550 mm, extendable to 3,000 mm ? Recess for excavator arm storage (LxWxH approx. 2,500 x 740 x 180 mm) SAF axles with air suspension Two-piece hydraulic ramps: 2,100 mm + 2,000 mm long, 650 mm wide incl. Hydraulic ramps adjustable Hydraulic rear support Wheel recess after the 2nd axle: Bjdexpmmmjpfx Ak Tswt ? Front wheel recess, top length approx. 2,000 mm x 1,100 mm, bottom depth approx. 350 mm Wheel recesses between 3rd and 4th axle: ? Rear wheel recess, top length approx. 1,300 mm x 550 mm, bottom depth approx. 220 mm

Condition: new, maximum load weight: 8,650 kg, overall weight: 11,900 kg, axle configuration: 2 axles, loading space length: 5,000 mm, loading space width: 2,420 mm, loading space height: 500 mm, Year of construction: 2026, * KA-TA-R 11.9 Masterline ----Brakes: * Wabco EBS * Emergency release system for spring brake cylinders * Drum brakes ----Axle: * 2 x 5.5 tons BPW axles ----Suspension: * Parabolic springs with tandem equalizer ----Drawbar / Flange coupling: * Height-adjustable drawbar by 300 mm with 40 mm flange coupling ----Electrical system / Lighting: * TPMS tire pressure monitoring system * Multivoltage * 15-pole power connector * 12 V 13-pole auxiliary cable * Extended connection cables for forestry and agricultural towing vehicles * LED tail lights ----General components: * Mechanical support crank at the front * 2 mechanical folding supports at the rear * Plastic tool box on the right side * 2-step footstep on the left side, facing forward * Underrun protection, bolted * Plastic quarter fenders ----Tipping body: * Net hooks on the side and at the rear in the bearings of the central locking system, as well as 2 pieces on the front wall * Steel pallet-sided 3-way tipping body (continuous side walls - without center rails - foldable with side panel spring lifters, foldable tailgate as well as pivoting via manual central locking) * 4 mm steel sheet floor * Mounting rail at the rear for loading ramps ----Load securing: * 1 x 5 tons lashing point in each corner * as well as 4 x 3 tons lashing points on each side, embedded in the outer frame ----Ramps: * 1 pair of aluminum loading ramps, approx. 3,310 x 400 mm (load capacity 8 tons / pair) suitable for rubber-tired and tracked vehicles * Lockable storage compartment at the rear under the loading area, integrated into the chassis ----Tires: * Tire size 385/55 R 19.5 ----Paint finish: Bwodpfx Akol Thw Ie Tjt * Chassis, drawbar, tipping body, front wall, folding supports and rear rails hot-dip galvanized * Axles, springs, air tank, flange coupling and support crank painted in a black tone * Painting of the side panels in RAL - 9010 pure white ----Information: * Body reinforced with load securing certificate according to EN 12642 XL * New vehicle with manufacturer's warranty * Subject to errors and prior sale ----Delivery time: * Available for immediate delivery from Egestorf

Condition: new, maximum load weight: 13,650 kg, overall weight: 18,000 kg, axle configuration: 2 axles, Year of construction: 2026, RAK 18.0 Outer Roller with Rear Tilting Function ----Brakes: * Wabco EBS-E (electronic braking system) * Emergency release system for spring brake cylinders * Drum brakes ----Axle: * BPW Eco Plus axles Bwsdpex Ipa Aofx Ak Tet ----Suspension: * Air suspension (automatic lowering when the brake is released) ----Drawbar: * Pneumatically lowerable drawbar, approx. 2,100 mm long, with 40 mm drawbar eye and height adjustment via coil spring and tension lock ----General Components: * Plastic toolbox - approx. 858 x 500 x 500 mm - on the right side * Closed plastic fenders, front and rear * Closed side underrun protection * Rear underrun protection, bolted on * Storage box for container nets, made of galvanized perforated sheet metal, approx. 1,000 x 500 x 500 mm * Folding A-frame sign at the rear * Rear impact protection buffer ----Electrical System / Lighting: * EBS multi-voltage system for towing vehicles with 12 & 24V electrical systems * 15-pole 24V power socket * LED lighting system for 12 & 24V * 2 additional LED reversing lights * TPMS (Tire Pressure Monitoring System) ----Suitable for Container Lengths: * For containers from 6,500mm to 7,000mm ----Container Running Surface / Tilting Bridge: * Roller guidance on the outside through flat steel edging with a clear distance of approx. 2,180 mm, in conjunction with 3 centering pieces on each side for container guidance * On the rear side, 2 recessed roller bearings connected to the tilting frame are installed to accommodate and stop the container rollers, with pneumatically operated locking to prevent longitudinal sliding * The positive locking of the roll containers is achieved via a pneumatic cross-locking unit installed in the tilting frame at the front and operable from the outside (single-side operation) * Chassis frame inside with rear-tilting main frame - motor-hydraulic tilting system in a single-cylinder design * Tilting angle 42° * Rubber pads between chassis and tilting frame * Loading of the containers takes place from the front, hot-dip galvanized chassis ----Tires: * Single tires 385/55 R 22.5 ----Loading Height: * Unloaded, approx. 1,270 mm ----Painting: * Underrun protection and locking parts (without topcoat) * Bogie, air tank, axles, swivel ring, and drawbar painted in a black color * Hot-dip galvanized ----Information: * For container transport according to DIN 30722 Part 1 * New vehicle without initial registration, with manufacturer's warranty * Errors and prior sale excepted ----Delivery Time: * Immediately available from Egestorf

Condition: new, maximum load weight: 13,650 kg, overall weight: 18,000 kg, axle configuration: 2 axles, Year of construction: 2026, * RAK 18.0 Outer Roller with Rear Tilting Function ----Brakes: * Wabco EBS-E (electronic braking system) * Emergency release system for spring brake cylinders * Drum brakes ----Axle: * BPW Eco Plus axles ----Suspension: * Air suspension (automatic lowering when the brake is released) ----Drawbar: * Pneumatically lowerable drawbar, approx. 2,100 mm long, with 40 mm drawbar eye and height adjustment via tension spring & locking bolt ----General Accessories: * Plastic tool box - approx. 858 x 500 x 500 mm - on the right side * Closed plastic fenders, front and rear * Closed side underrun protection * Rear underrun protection, bolted on * Storage box for container nets, made of galvanized perforated sheet metal, approx. 1,000 x 500 x 500 mm * Foldable A-sign at the rear * Rear impact protection buffer ----Electrical System / Lighting: * EBS multi-voltage system for towing vehicles with 12 & 24V electrical systems * 15-pin 24V power connector * LED lighting system for 12 & 24V * 2 additional LED reversing lights * TPMS tire pressure monitoring system ----Suitable for Container Lengths: * For containers from 6,500 mm to 7,000 mm ----Container Running Surface / Tilting Bridge: * External roller guide through flat steel edging with a clear distance of approx. 2,180 mm in conjunction with 3 centering pieces on each side for container guidance * To accommodate and stop the container rollers, 2 recessed roller bearings connected to the tilting frame are mounted on the rear side, with pneumatic actuation to prevent slippage in the longitudinal direction * The positive locking of the roll-off containers is achieved via a pneumatic cross-bracing unit installed in the front of the tilting frame and operable from the outside (single-sided operation) * Chassis frame with rear tilting main frame - hydraulic tilting system in single-cylinder design * Tilting angle 42° * Rubber pads between chassis and tilting frame * The containers are pushed on from the front, hot-dip galvanized chassis ----Tires: * Single tires 385/55 R 22.5 ----Loading Height: * Unladen approx. 1,270 mm ----Painting: * Underrun protection and locking parts (without topcoat) * Turntable, air tank, axles, slewing ring and drawbar painted in a black tone * Hot-dip galvanized ----Information: Bsdpfxex Ipbmo Ak Tjwt * For container transport according to DIN 30722 Part 1 * New vehicle without initial registration, with manufacturer's warranty * Subject to errors and prior sale ----Delivery Time: * Immediately available from Egestorf

Condition: new, maximum load weight: 8,650 kg, overall weight: 11,900 kg, axle configuration: 2 axles, loading space length: 5,000 mm, loading space width: 2,420 mm, loading space height: 500 mm, Year of construction: 2026, * KA-TA-R 11.9 Masterline ----Brakes: * Wabco EBS * Emergency release system for spring brake cylinders * Drum brakes ----Axles: * 2 x 5.5 ton BPW axles ----Suspension: * Parabolic springs with tandem equalizer ----Drawbar / Flange coupling: Bwsdpfeq Euagjx Ak Tjt * Height-adjustable drawbar by 300 mm with 40 mm flange coupling ----Electrical system / Lighting: * TPMS tire pressure monitoring system * Multivoltage * 15-pin power connector * 12 V 13-pin auxiliary cable * Extended connection cables for forestry and agricultural tractors * LED tail lights ----General components: * Mechanical support winch at the front * 2 mechanical folding supports at the rear * Plastic tool box on the side, right * 2-step step on the left side in the direction of travel at the front * Underrun protection, bolted * Plastic fender ----Tipping body: * Lashing hooks on the side and rear in the bearings of the central locking system, as well as 2 pieces on the front wall * Steel pallet-sided, 3-way tipping body (continuous side walls - without center rails - foldable with side board spring lifts, tailgate foldable and pivoting via manual central locking) * 4 mm steel sheet floor * Mounting rail at the rear for loading ramps ----Load securing: * 1 x 5-ton lashing point in each corner * As well as 4 x 3-ton lashing eyes on each side, embedded in the outer frame ----Ramps: * 1 pair of aluminum loading ramps, approx. 3,310 x 400 mm (load capacity 8 tons / pair), suitable for vehicles with rubber and chain tracks * Lockable storage compartment at the rear below the loading area, integrated into the chassis ----Tires: * Tire size 385/55 R 19.5 ----Paintwork: * Chassis, drawbar, tipping body, front wall, folding supports, and rear frame hot-dip galvanized * Axles, springs, air tank, flange coupling, and support winch painted in a black tone * Painting of the side boards in RAL - 9010 pure white ----Information: * Body reinforced with load securing certificate according to EN 12642 XL * New vehicle with manufacturer's warranty * Errors and prior sale are subject to change ----Delivery time: * Available for immediate delivery from Egestorf

Condition: new, maximum load weight: 8,800 kg, overall weight: 11,900 kg, axle configuration: 2 axles, loading space length: 5,370 mm, loading space width: 2,470 mm, loading space height: 400 mm, Year of construction: 2025, * ETÜ-TA-R 11.9: ----Brakes: * EBS braking system * Emergency release device for spring-loaded cylinders * Drum brakes, 2 x 5.5 t ----Axles: * Gigant axles ----Suspension: * Parabolic springs with compensating unit ----Drawbar / Flange Towing Eye: * Height-adjustable drawbar, adjustable by 300 mm * 40 mm flange towing eye ----General Attachments: * Jost landing gear at front * External foldable support legs at rear * Plastic toolbox on the front right outside, mounted on the bulkhead * Side underrun protection * Plastic quarter mudguards ----Electrics / Lighting: * TPMS (tire pressure monitoring system) * LED lighting ----Loading Platform: * Loading area 5.37 m * 50 mm softwood floor * Bolt-on bulkhead made of flat sheet metal * Side walls made of trapetzoidal-profiled steel, foldable with drop-side spring assist * Rear wall made of steel, can be slid between the ramp holders for storage in front of the bulkhead when not in use * Rear stakes bolted ----Load Securing: * Outer frame with perforations, bent approx. 45 degrees, lashing capacity 2 t every 480 mm * Installation of 3 t folding lashing rings every 600 mm possible * In each front and rear corner, one lashing ring, 6.3 t each * Various holes in the bulkhead and rear crossmember for 1.2 t lashing options ----Ramps: * One-piece mechanical grid ramps with spring system for single-person operation, approx. 2,750 x 600 mm (can be pushed together to 20 mm) * Rear approach angle approx. 860 mm from chassis ----Tyres: Bwsdpfxjl Th Ncs Ak Tjt * Tyres 235/75 R 17.5 ----Wheelbase: * Wheelbase: 990 mm ----Paintwork: * Drawbar, bulkhead, tailgate, foldable supports, and drive-on ramps hot-dip galvanized * Axles, springs, air tanks, and 40 mm flange towing eye painted in black shade * Side wall paintwork in RAL2011 deep orange * Custom color paintwork for side panels available for an additional charge ----Information: * New vehicle with manufacturer's warranty * Subject to errors and prior sale ----Delivery time: * Available immediately from Egestorf

Condition: new, maximum load weight: 10,500 kg, overall weight: 14,400 kg, axle configuration: 2 axles, loading space length: 7,000 mm, loading space width: 2,470 mm, loading space height: 400 mm, Year of construction: 2026, * EBS (electronic braking system) * Emergency release device for spring-loaded cylinder * Drum brakes * 2 x 7-ton Gigant axles * Air suspension with lifting and lowering system * Drawbar adjustable in height by 300 mm * Drawbar extension by 250 mm to 2,250 mm * Tire pressure monitoring with display option in the truck via EBS signal - without installation on the truck side * 15-pin power connector * LED lighting * Front support jacks * Outboard folding supports at the rear * Plastic tool box approx. 858 x 500 x 500 mm on the front right side, on the front wall * Side underrun protection * Plastic quarter fender * 50 mm softwood floor * Before the front wall and at the rear, provision for subsequent installation of 20" container locking mechanisms * Bolted front wall made of smooth sheet metal * Side walls made of steel sheet - trapezoidal profile - foldable, divided in the middle * Steel rear wall, slidable between the ramps, with mounting bracket for storage inside, in front of the front wall when not in use * Rear cross members screwed on * Perforated outer frame, bent at approx. 45 degrees, with a lashing force of 2 tons every 480 mm * Installation of 3-ton drop-side lashing eyes every 600 mm possible - 4 lashing eyes installed on each side * One 6.3-ton lashing eye each in the corners at the front and rear * Profifix lashing bar in the longitudinal axis, in the middle, for lashing with a load capacity of up to 3000 daN * Various holes in the front and end beam for 1.2-ton lashing * One-piece mechanical grating ramp with spring mechanism for single-person operation, approx. 2,750 x 600 mm (can be pushed together to 20 mm) * Approach angle at the rear, approx. 860 mm Bwjdpol Thvxefx Ak Tst * Chassis, drawbar, front wall, rear tailgate, folding supports and ramps hot-dip galvanized * Axles, springs, air tanks, flange couplings and support jacks painted in a black tone * Sideboards in RAL 9010 pure white * --reinforced and certified body according to EN 12642 XL incl. load securing certificate-- * New vehicle with manufacturer's warranty * Errors and prior sale subject to change * Available for immediate delivery from Egestorf

Condition: new, maximum load weight: 10,400 kg, overall weight: 14,400 kg, axle configuration: 2 axles, loading space length: 5,500 mm, loading space width: 2,420 mm, loading space height: 500 mm, Year of construction: 2026, * ETK-TA-R 14.4: ----Brakes: * EBS * Emergency release system for spring brake cylinders * Drum brakes ----Axle: * 2 x 7-ton Gigant axles ----Suspension: * Parabolic springs with tandem equalizing unit ----Drawbar / Flange coupling: * Drawbar adjustable in height by 300 mm with 40 mm flange coupling ----Electrical system / Lighting: * Tire pressure monitoring system with display option in the truck via EBS signal, without installation on the truck side * 15-pole power connector * LED tail lights ----General components: * Mechanical support winch at the front * 2 mechanical folding supports at the rear * Plastic toolbox approx. 750 x 350 x 300 mm on the right side * Bolted underbody protection * Plastic quarter fenders Bsdpfx Akjtr St Uj Towt ----Frame: * Main frame made of fine-grain steel ----Tipping body: * Net hooks on the side and at the rear in the bearings of the central locking system, as well as 2 pieces on the front wall * Steel pallet-sided, 2-way tipping body, front wall fixed, made of smooth sheet metal, continuous side walls - without center rails, foldable with side board spring lifters, and pivoting via manual central locking * Rear rails bolted * Steel rear wall inserted in front of the ramps * 1 x 5-ton lashing eye in each corner, as well as 4 x 3-ton lashing eyes on each side, embedded in the outer frame * 4 mm floor made of fine-grain steel ----Ramps: * Two-part mechanical grating ramps with aluminum tip, 2,150 + 1,300 mm x 600 mm (manually adjustable to 80 mm) ----Painting: * Chassis, drawbar, rear rails, underbody protection, mechanical fall supports and ramps hot-dip galvanized * Axles, springs, air tanks, flange coupling and support winch painted in a black shade * Side boards and tipping body in RAL 9010 pure white * Painting of the side walls and tipping body in a RAL color is possible for an extra charge ----Information: * New vehicle with manufacturer's warranty * Errors and prior sale excepted ----Delivery time: * Available for immediate delivery from Egestorf

Condition: new, maximum load weight: 10,750 kg, overall weight: 14,400 kg, axle configuration: 2 axles, loading space length: 7,000 mm, loading space width: 2,470 mm, loading space height: 400 mm, Year of construction: 2026, * ETÜ-TA-R 14.4: ----Brakes: * EBS braking system * Emergency release system for spring brake cylinders * Drum brakes ----Axles: * 2 x 7-ton Gigant axles ----Suspension: * Parabolic springs with equalizing unit ----Drawbar / Flange coupling: * Drawbar with 300 mm height adjustment * Drawbar extension by 250 mm to 2,250 mm * 40 mm flange coupling ----Electrical system / Lighting: Bwodpfx Aksv D Tcbs Tet * TPMS tire pressure monitoring system * 15-pin power connector * LED lighting ----General attachments: * Support winch at the front * Outboard folding supports at the rear * Plastic tool box approx. 858 x 500 x 500 mm on the front right outside on the front panel * Lateral impact protection * Plastic quarter fenders ----Low-loader platform: * 50 mm hardwood flooring * In front of the front panel and rear slope, provision for retrofitting container locking mechanisms for the transport of 20" containers * Screwed front panel made of smooth sheet metal * Steel sheet metal side walls - trapezoidal profile - foldable in the middle, divided 1x * Steel rear wall can be slid in between the ramp brackets when not in use, inside in front of the front panel * Rear crossbeams screwed on ----Load securing: * Perforated outer frame approx. 45 degrees bent with 2-ton lashing force every 480 mm * Installation of 3-ton drop-side lashing eyes possible every 600 mm * In the corners, front and rear, 1 x 6.3-ton lashing point each * In the front and end beam, various holes for 1.2-ton lashing options * Profifix lashing rail in the longitudinal axis in the middle for lashing up to LC 3000 daN ----Ramps: * One-piece mechanical grating ramps with spring mechanism for single-person operation approx. 2,750 x 600 mm (can be pushed together to 20 mm) * Approach angle at the rear approx. 860 mm chassis ----Wheelbase: * Wheelbase 1,140 ----Painting: * Drawbar, front panel, rear door, folding supports and ramps hot-dip galvanized * Axles, springs, air tanks, flange coupling and support winch painted in a black tone * Painting of the side walls in RAL - 9010 pure white ----Information: * Reinforced and certified body according to EN 12642 XL incl. load securing certificate * New vehicle with manufacturer's warranty * Errors and prior sale reserved ----Delivery time: * Immediately available from Egestorf

Condition: new, maximum load weight: 14,550 kg, overall weight: 18,000 kg, axle configuration: 2 axles, loading space length: 7,000 mm, Year of construction: 2026, RA-T 18.0: Loadable from the front and rear ----Brakes: * Wabco EBS-E (electronic braking system) * Emergency release system for spring brake cylinders * Disc brakes 19.5" * Automatic braking when the transverse locking units are opened ----Axles: * 2 x 10-ton BPW wide-track axles ----Suspension: * Air suspension (automatic lowering when the brake is released) ----Electrical system / Lighting: * Tire pressure monitoring system with display option in the truck via EBS signal – without truck-side installation * 15-pin power connector * LED lighting system with protective cover * 2 LED reversing lights (switched via reverse gear) ----Drawbar: * Pneumatically lowerable drawbar, 1,800 mm long, with 40 mm drawbar eye and height adjustment via tension spring & locking clamp ----General components: * Plastic tool box 858 x 500 x 500 mm on the right side * Storage box for container nets made of galvanized perforated sheet metal, 1,000 x 500 x 500 mm on the side * Closed plastic wheel arches, front and rear * Closed side impact protection (RAL 9010 pure white) as an advertising area * Underrun protection at the rear * Plastic impact protection buffer at the rear Bwsdpfjl Tn U Rsx Ak Tot * Foldable A-frame sign * Hazardous goods sign with accompanying document pocket and reflective parking warning sign at the rear ----Container area: * Loading possible from the front with lowering of the roller track at the rear and plug-in stops * Roller recesses in the area of the swivel ring with mechanically adjustable stop angles (2 positions) at the front left and right on the roller tracks * Roller track length approx. 6,830 mm * Pneumatic 4-point clamping lock * For the transport of external roll-off containers according to DIN 30722 Part 1 - Dekra load securing certificate available ----Loading height: * When loaded, approx. 1,130 mm ----Painting: * Chassis and locking parts hot-dip galvanized * Air tank, axles, swivel ring and drawbar painted in a black tone ----Information: * --Technically possible gross vehicle weight of 20,000 kg-- * New vehicle without initial registration with manufacturer's warranty * Errors and prior sale excepted * Sample images ----Delivery time: * Available for immediate delivery from Egestorf

Condition: new, maximum load weight: 8,870 kg, overall weight: 11,900 kg, axle configuration: 2 axles, loading space length: 6,270 mm, loading space width: 2,470 mm, loading space height: 400 mm, Year of construction: 2026, * ETÜ-TA-R 11.9: Bwedpfx Aervvfwsk Tst ----Brakes: * EBS braking system * Emergency release device for spring brake cylinders * Drum brakes ----Axle: * 2 x 5.5 ton BPW axles ----Suspension: * Parabolic springs with equalizer ----Drawbar / Flange coupling: * Height-adjustable drawbar by 300 mm * 40 mm flange coupling ----General components: * Jost support leg at the front * Outboard, hot-dip galvanized folding supports at the rear * Plastic quarter fenders * Plastic toolbox at the front right on the front panel ----Electrical system / Lighting: * TPMS tire pressure monitoring system * LED lighting ----Loading platform: * Loading platform 6.27 m * Suitable for container transport * 50 mm softwood floor * Provision on the front panel for subsequent installation of container locking mechanisms * Bolted front panel made of smooth sheet metal * Side walls made of trapezoid-profiled steel sheet, foldable with spring-loaded side rails * Steel rear wall can be slid in between the ramp supports when not in use, positioned inside the front panel * Rear crossbars bolted ----Load securing: * Perforated outer frame, angled at approx. 45 degrees, with a lashing force of 2 tons every 480 mm * Installation of 3-ton lashing eyes possible every 600 mm * One 6.3-ton lashing eye at each corner at the front and rear * Various holes in the front and end beams for 1.2-ton lashing options ----Ramps: * One-piece mechanical loading ramps with spring mechanism for single-person operation, approx. 2,750 x 600 mm (can be pushed together to 20 mm) * Approach angle at the rear, approx. 860 mm ----Tires: * Tires: 235/75R17.5 ----Wheelbase: * Wheelbase: 990 mm ----Painting: * Hot-dip galvanized chassis, drawbar, front panel, rear wall, rear crossbars and loading ramps * Painting of the side rails in RAL 9010 pure white * Painting of the side walls in a RAL color is possible for an extra charge ----Information: * Errors and prior sale subject to change * New vehicle with manufacturer's warranty ----Delivery time: * Available for immediate delivery from Egestorf

Condition: new, maximum load weight: 10,400 kg, overall weight: 14,400 kg, axle configuration: 2 axles, loading space length: 5,500 mm, loading space width: 2,420 mm, loading space height: 500 mm, Year of construction: 2026, * ETK-TA-R 14.4: ----Brakes: * EBS * Emergency release system for spring brake cylinders * Drum brakes Bwedpstr Sucjfx Ak Tet ----Axles: * 2 x 7-ton Gigant axles ----Suspension: * Parabolic springs with tandem equalizer ----Drawbar / Flange coupling: * Height-adjustable drawbar by 300 mm with 40 mm flange coupling ----Electrical system / Lighting: * Tire pressure monitoring system with display option in the truck via EBS signal without truck-side installation * 15-pole power socket * LED tail lights ----General components: * Mechanical support jacks at the front * 2 mechanical folding supports at the rear * Plastic toolbox approx. 750 x 350 x 300 mm on the right side * Bolted underrun protection * Plastic quarter fenders ----Frame: * Main frame made of fine-grain steel ----Tipping platform: * Net hooks on the side and rear in the bearings of the central locking system, as well as 2 pieces on the front wall * Steel pallet-sided 2-way tipping body, front wall fixed, made of smooth sheet metal, continuous side walls - without center rails, foldable with side board spring lift and pivoting via manual central locking * Rear rails bolted on * Steel rear wall inserted in front of the ramps * 1 x 5-ton lashing point in each corner, as well as 4 x 3-ton lashing eyes on each side embedded in the outer frame * 4 mm floor made of fine-grain steel ----Ramps: * Two-part mechanical grid ramps with aluminum tip, 2,150 + 1,300 mm x 600 mm (manually adjustable up to 80 mm) ----Painting: * Chassis, drawbar, rear rails, underrun protection, mechanical support jacks, and ramps hot-dip galvanized * Axles, springs, air tanks, flange coupling, and support jacks painted in a black tone * Side boards and platform painted in RAL 9010 pure white * Painting of the side walls and tipping platform in a RAL color is possible for an extra charge ----Information: * New vehicle with manufacturer's warranty * Errors and prior sale excepted ----Delivery time: * Available immediately from Egestorf

Condition: new, maximum load weight: 10,500 kg, overall weight: 14,400 kg, axle configuration: 2 axles, loading space length: 7,000 mm, loading space width: 2,470 mm, loading space height: 400 mm, Year of construction: 2026, * EBS (electronic braking system) * Emergency release device for spring brake cylinders * Drum brakes * 2 x 7-ton Gigant axles * Air suspension with lifting and lowering system * Drawbar adjustable by 300 mm in height * Drawbar extension by 250 mm to 2,250 mm * Tire pressure monitoring with display option in the truck via EBS signal - without truck-side installation * 15-pole power connector * LED lighting * Front support jacks * Outboard, folding support legs at the rear * Plastic tool box approx. 858 x 500 x 500 mm on the front right outside on the front panel * Side underrun protection * Plastic quarter fenders * 50 mm hardwood flooring * Device for retrofitting 20" container locking mechanisms in front of and behind the front panel * Bolted front panel made of smooth sheet metal * Side walls made of steel sheet - trapezoid-profiled - foldable, divided in the middle 1x * Steel rear wall can be slid between the ramps, stored when not in use inside the front panel * Rear cross members bolted * Perforated outer frame approx. 45 degrees bent with 2-ton lashing force every 480 mm Bsdpfx Ajl Th Dfsk Towt * Installation of 3-ton lashing eyes every 600 mm possible - 4 lashing points installed on each side * 1 x 6.3-ton lashing point in each front and rear corner * Profifix lashing rail in the longitudinal axis in the middle for lashing up to LC 3000 daN * Various holes in the front and end cross member for 1.2-ton lashing * One-piece mechanical grating access ramps with spring mechanism for single-person operation approx. 2,750 x 600 mm (can be slid together to 20 mm) * Approach angle at the rear approx. 860 mm * Chassis, drawbar, front panel, tailgate, folding support legs and access ramps hot-dip galvanized * Axles, springs, air tanks, flange couplings and support jacks painted in a black tone * Side boards in RAL 9010 pure white * --reinforced and certified body according to EN 12642 XL incl. load securing certificate-- * New vehicle with manufacturer's warranty * Errors and prior sale excepted * Immediately available from Egestorf