Used Faymonville Open Flatbed Semitrailers for sale (222)

Condition: new, maximum load weight: 37,635 kg, overall weight: 48,000 kg, axle configuration: 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory, including vehicles available immediately and at short notice, on our website. Excerpt from equipment features. Complete specifications available on request. Gooseneck: * Gooseneck with front corners beveled approx. 45° and rear chamfer approx. 750 mm x 10° * 3 pairs of lashing rings (LC 5,000 daN) * Hardwood flooring approx. 30 mm thick One-piece steel ramps: * One pair of galvanized one-piece steel ramps, approx. 3,000 x 800 mm, with approx. 48 mm thick hardwood covering * Ramps with hydraulic lifting mechanism, hydraulically adjustable * Maximum load per pair: 40,000 kg In accordance with Regulation 1230/2012/EU, ramps shorter than 300 mm in driving position do not count towards the vehicle length Loading area: * 1 pair of fixed wheel recesses in front of the axles, approx. 2,610 x 970 x 400 mm (L x W x D) * Wheel recesses with square climbing strips approx. 15 x 15 mm as well as extensions in the lower area * Between the first and second axles, one pair of fixed wheel recesses, approx. 1,610 x 700 x 400 mm (L x W x D). Includes three-piece removable galvanized covers over the wheel recesses (W approx. 670 mm) – max. point load 5 t/each * Recess in the inclined area as well as projecting into the loading area to accommodate excavator boom (approx. 2,900 x 750 x 210/290 mm (L x W x H)) * 1 pair of lashing rings (horizontal) at the front of the loading area (LC 10,000 daN) * 5 pairs of fold-out lashing rings (LC 5,000 daN) * 3 pairs of fold-out lashing rings (LC 10,000 daN), 2 pairs of lashing rings in the excavator boom recess (LC 5,000 daN) * Cut-outs in the outer frame of the loading area to hook in tensioning straps (LC 2,000 daN) Iodsxtc Ubjpfx Afhoal Landing legs: * JOST landing legs (mechanical) with 2-speed gearbox, lifting capacity approx. 24 t (test load approx. 50 t) Axles: * BPW axles and suspension, 2 rigid axles, 1 trailing steering axle * Technical axle load: 12,000 kg each * Electromagnetic reversing lock, activated via reverse gear and manually * Air suspension with lift/lowering valve * Axle tool kit Tyres: * Tyres 235/75 R 17.5 3PMSF – brand at our discretion * TPMS: Tyre Pressure Monitoring System in accordance with ECE R 141. Data is transmitted to the tractor via standardized EBS interface according to ISO 11992. For correct display, the tractor unit must be able to receive and display this data Braking system: * WABCO brake system in accordance with EU regulations, with EBS-E (2S2M) and without connection lines to the tractor unit Steel construction: * Steel structure made of high-strength fine-grained steels * Steel grades: S355J2+N/S355MC (yield strength 355MPa), S690QL/S700MC (yield strength 690MPa) Electrical system: * Electrical system in accordance with EU regulations, 24-volt ASPÖCK-NORDIK (ASS3) lighting * ASPÖCK-UNIBOX at front connection strip with 24N, 24S & 15-pin sockets * Connections according to ISO: 24N ISO-1185, 24S ISO-3731, 15-pin ISO-12098 Paintwork: * Complete steel construction automatically shot-blasted with turbine blasting machine after welding * Second blasting treatment with corundum for optimum coating adhesion * Final coating with 2 layers of 2K topcoat, single color in RAL 3002 Carmine Red as per RAL system 841GL * Rims in silver * Rear section metallized and painted in RAL 9010 (Pure White) * Paint system tested in salt spray mist test according to ISO 9227-NSS * Cavity sealing with special wax Including the following extras: * 2-inch kingpin * One

Condition: used, color: green, Year of construction: 2015, Faymonville F-S44-1ACA. Year of manufacture: 2015. 10-ton SAF axles. Unladen weight: 22,250 kg. Payload capacity: 57,750 kg. Iaedpexrucnjfx Afhol Gross vehicle weight: 80,000 kg. Kingpin load: 40,000 kg. EBS, ABS, ALB. Hydraulics powered via NATO connection from the truck. Aluminium side boards on the gooseneck. Hydraulically detachable gooseneck. Air suspension. Extendable by 5 meters. Radio remote control. Excavator recess: 5,600 mm x 950 mm. Tyres: 235/75R17.5, 80% tread remaining. Dimensions: Neck: Length: 4,900 mm. Width: 2,500 mm. Height: 1,800 mm. Kingpin height: 1,300 mm. Bed: Length: 8,000 mm. Width: 2,750 mm. Height: 500 mm. Deck thickness: 300 mm. Rear section: Length: 5,600 mm. Width: 2,750 mm. Height: 1,050 mm. Dolly D-2. Year of manufacture: 2015. 10-ton SAF axles. Unladen weight: 3,650 kg. Gross vehicle weight: 36,100 kg. Kingpin load: 16,100 kg. Air suspension. Tyres: 235/75R17.5, 70% tread remaining. German trailer! 4 units available! ID No: 590. The General Terms and Conditions of Heinhuis apply to all advertisements, offers, and quotations by Heinhuis, all contracts entered into by Heinhuis, and all related negotiations. By responding in any way, you accept the applicability of Heinhuis’s General Terms and Conditions and declare you have taken note of these conditions. Our prices are export net prices. = Further information = Year of manufacture: 2015 Unladen weight: 22,250 kg Payload capacity: 57,750 kg Gross vehicle weight: 80,000 kg Extendable body: Yes Price: On request = Company information = For more information: WhatsApp:

Condition: used, empty load weight: 10,300 kg, maximum load weight: 39,200 kg, overall weight: 49,500 kg, axle configuration: 3 axles, first registration: 01/2025, loading space length: 9,300 mm, loading space width: 2,540 mm, loading space height: 860 mm, suspension: air, tire size: 235/75 R 17.5 3PMSF, color: grey, Year of construction: 2025, operation weight: 10,300 kg, Equipment: ABS, For every used semi-trailer, you receive a current and comprehensive inspection and functional report. Gooseneck: - Gooseneck with rear bevel approx. 750 mm x 10° - 3 pairs of lashing rings (LC 5,000 daN) - Hardwood flooring 30 mm thick Loading Area: - Loading area hydraulically liftable and lowerable behind the gooseneck, approx. 2,800 mm long, with rear bevel approx. 1,000 mm x 8° - 6 pairs of folding external lashing rings (LC 5,000 daN) - 2 pairs of folding external lashing rings (LC 10,000 daN) - 1 pair of folding internal lashing rings on the front center beam (LC 10,000 daN) - Cut-outs in the outer frame of the loading area for securing straps (LC 2,000 daN) - Hardwood flooring approx. 48 mm thick, over the axles with checker plate covering Two-piece Steel Ramps: - One pair of galvanized, two-piece steel ramps approx. 2,750 + 1,400 x 800 mm with approx. 48 mm thick hardwood covering - Ramps hydraulically foldable (raise/lower) and hydraulically adjustable - Maximum load capacity per pair: 40,000 kg Axles, Suspension and Tyres: - BPW axles and suspension, 2 rigid axles, 1 steering trailing axle Ijdpfx Afexnarmjhoal - Technical axle load: 12,000 kg - Electromagnetic reverse lock, activated via reverse gear or manually - Air suspension with lift and lower valve - Axle tools - Tyres: 235/75 R 17.5 3PMSF - TPMS tyre pressure monitoring system in accordance with ECE R 141 Included Accessories: - One spare wheel with holder - 2" king pin - One galvanized steel front wall approx. 400 mm high - Yellow-red air couplings at the galvanized front connection strip - 4 wheel chocks with holders - Galvanized folding supports beneath the rear loading area bevel - Mount for rotating beacon at the rear of the trailer - Cover plates to bridge the gap between ramps and loading area - Electro-hydraulic unit at the rear, under the loading area - Mounts for warning boards left and right at the gooseneck and ramps, including socket - On the gooseneck, plug-in aluminium side walls and rear wall approx. 2,440 x 400 mm - Rear galvanized plug-in posts are removable (superstructure length approx. 2,560 mm) - Electric winch with radio remote control, approx. 5,400 kg pulling force, including 9.5 mm steel rope, 24 m long, with rope guide roller - Bolt-on 5t ring for routing winch cable on the neck without return pulley - 2 pairs of WADER container locks in the loading area for a 20ft container - 6 pairs of pocket sockets for plug-in posts approx. 100 x 50 mm in the outer frame of the loading area - Lift axle on the front axle, controlled by TEBS E depending on current axle load and loading condition - 7 pairs of recessed lashing rings along the center beam (LC 5,000 daN) - 2 pairs in the lift bed - 5 pairs in the rear part of the loading area - 1 pair of recessed lashing rings along the center beam at the rear bevel (LC 10,000 daN) - Anti-slip sand coating applied on the checker plate surfaces on gooseneck and loading area - BEKAMAX (Pico) central lubrication system, with standard grease NLGI-2 - Four warning signs, extendable by approx. 400 mm, approx. 423 x 423 mm - Load manometer for determining axle loads, including loading diagram - HRM Metallization (High Resistance Metallisation) of the outer frame - Complete steel construction shot-blasted, then all specified visible surfaces metallized with ZINACOR 850 (zinc 85% - aluminium 15%) by hot finishing

Condition: used, empty load weight: 14,100 kg, maximum load weight: 33,900 kg, overall weight: 48,000 kg, axle configuration: > 3 axles, first registration: 11/1999, suspension: air, tire size: 235/75 17,5, tire condition: 50 %, color: green, Year of construction: 1999, front tire size: 235/75 17,5, rear tire size: 235/75 17,5, driver cabin: day cab, emission class: none, Equipment: truck registration, Reference number for inquiries: 68574 Faymonville, Flatbed Trailer * Year of manufacture: 1999 * Air suspension * Steering axle * Forced-steered axle * Compressed air coupling head (red + yellow) * Connection plug: 2x7-pin * Lift and lower device * Extendable - telescopic semi-trailer * Suspension: Air Iaedpjv Rvgcjfx Afhel * Gross vehicle weight: 48,000 kg * Unladen weight: 14,100 kg * Payload: 33,900 kg * Permissible total weight: 48,000 kg * Axle manufacturer: SAF * Tyre condition, 1st axle: 50% -- 50% - Tyre size: 235/75 R17.5 * Tyre condition, 2nd axle: 50% -- 50% - Tyre size: 235/75 R17.5 * Tyre condition, 3rd axle: 50% -- 50% - Tyre size: 235/75 R17.5 * Tyre size: 235/75 R17.5 * Manufacturer: ES-GE * Extension faulty * Steering axles not functional * Mobile Disclaimer: Subject to alterations, prior sale, and errors excepted. More photos and videos are available on our website. Our comprehensive services include, for example: * Purchase/sale/rental of commercial vehicles * Fast and hassle-free financing * Arranging all (export) documentation * Order of export/customs number plates * Vehicle preparation: new tarpaulins, lettering, painting, etc. * Professional loading and load securing * TÜV inspections, registration services * Transfer/transport of commercial vehicles Contact our trained staff for advice—we are happy to assist you.

Condition: excellent (used), first registration: 09/2015, loading space length: 20,180 mm, loading space width: 3,000 mm, Year of construction: 2015, YAFTL2007F0017329 = More information = Empty weight: 13,600 kg Payload: 28,400 kg GVW: 42,000 kg Extendable body: Yes Technical condition: very good Visual condition: very good Damage: none Contact Sales for more information. = Company information = If you have any questions or suggestions, Don't hesitate to contact us. We guarantee an answer within 8 hours. Prices are without VAT. No rights could be derived from given information. Office Phone: MOB: Nederlands - English - Deutsch - Francais - Español - Italiano)Available on What's App and Viber. Iasdpfsrywukjx Afhjl MOB: Nederlands) Available on What's App and Viber. When you pay by bank transfer, the money needs to be tranfered to our Bank Account underneath. Always check the payment details that are stated on our website. In case you have received other information please contact us. In case you have doubts please call us so we can verify the invoice and/or payment. Bench details: Rabobank Lane of Limburg 2 4701BP Roosendaal IBAN: NL 89 RABO EORI/BTW/TAX: NL857401B(01) BIC/SWIFT: RABONL2U

Condition: excellent (used), axle configuration: 3 axles, first registration: 07/2016, suspension: air, Year of construction: 2016, Equipment: tail-lift, Suspension: Air suspension Rear axle 1: Steered Rear axle 2: Steered Rear axle 3: Steered gVW: 48,000 kg Technical condition: Very good Visual condition: Very good Price: On request Please contact David F Middelman for further information. Iedpfevvwzrsx Afhoal

Condition: new, maximum load weight: 36,370 kg, overall weight: 45,000 kg, axle configuration: 3 axles, Equipment: ABS, You can find our full vehicle inventory, including immediately and soon-available vehicles, on our website. Excerpt from the equipment. Full equipment details available on request. Load area: - Load area made of hardwood floor with rear chamfer, approx. 1,000 mm x 8° - 2 pairs of lashing rings (LC 5,000 daN) - 1 pair of lashing rings (LC 10,000 daN) - 6 pairs of fold-out lashing rings to the outside (LC 5,000 daN) - 2 pairs of fold-out lashing rings to the outside (LC 10,000 daN) - Cut-outs in the outer frame of the load area for hooking in tie-down straps (LC 2,000 daN) Landing legs: - JOST mechanical landing legs with 2-speed gearbox for approx. 24 t lifting capacity (approx. 50 t test load) Axles: - BPW axles, air-suspended, with disc brakes (approx. 377 mm), with lift/lower function (ET 120) - Axle tools Tyres: Iodpfx Afoxq I Dvehoal - Tyres 435/50 R 19.5 TPMS: - TPMS tyre pressure monitoring system according to ECE R 141 Data transfer to the truck is via the standardised EBS interface according to ISO 11992. For correct display, the truck must be able to transmit and display this data. Brake system: - Wabco braking system compliant with EU regulations, with EBS-E (2S2M) and without connection lines to the tractor unit Steel structure: - Steel construction made of high-strength fine-grain steels Steel grades: S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa) Electrical system: - Electrical system in accordance with EU regulations - Lighting 24 Volt ASPÖCK-NORDIK (ASS3) - ASPÖCK-UNIBOX at the front connection strip with 24N, 24S & 15-pin sockets as per ISO. 24N ISO-1185, 24S ISO-3731, 15-pin ISO-12098 Paintwork: - Complete steel structure automatically shot-blasted after welding with blast wheel machine - Second blast treatment with corundum for optimum coating adhesion - HRM metallisation of the entire vehicle chassis with ZINACOR 850 (85% zinc / 15% aluminium) for best corrosion protection - Final painting with 2 layers of 2K topcoat, single colour in RAL 3002 Carmine Red according to RAL system 841GL - Rear section metallised and painted in RAL 9010 (Pure White) - Paint build-up tested in salt spray test in accordance with ISO 9227-NSS - Sealing of cavities with special wax - Metallic paintwork not possible Including the following additional equipment: - Yellow-red air couplings on the galvanised front connection strip - 4 wheel chocks with holder - 2-inch kingpin - Yellow reflector tape on the sides and rear of the trailer according to EU regulations - European reflector plates (red-yellow) on the rear of the trailer - Load area with heavy-duty hardwood floor - 1 spare wheel holder under the loading platform on the right side in the direction of travel - Galvanised drop-down supports under the chamfer of the loading area - 9 pairs of stanchion pockets for insertable stanchions, approx. 100 x 50 mm, in the outer frame of the loading area - One holder for a rotating beacon on the rear of the trailer - On the gooseneck and on the left and right rear panel, each with a bracket for warning signs including socket - One galvanised holder transversely under the loading area (approx. 2,400 x 640 x 165 mm) - One galvanised steel front wall (EN12642-XL), approx. 1,600 mm high - A layer of paint with sand on the central beam as anti-slip protection - 6 pairs of WADER container sockets fitted in the loading area, for 1x 20' container, 2x 20' containers or 1x 40' container - 3 pairs of transverse stanchion pocket rails moun

Condition: used, color: green, Year of construction: 2015, Faymonville F-S44-1ACA. Year of manufacture: 2015. 10 t SAF axles. Unladen weight: 22,250 kg. Load capacity: 57,750 kg. Gross vehicle weight (GVW): 80,000 kg. Kingpin load: 40,000 kg. EBS, ABS, ALB. Hydraulics operated via NATO connection from the truck. Aluminum side boards on the gooseneck. Hydraulically detachable gooseneck. Air suspension. Extendable by 5 meters. Radio remote control. Excavator deck: 5,600 mm x 950 mm. Tyres: 235/75R17.5, 80% remaining tread. Dimensions: Gooseneck: Length: 4,900 mm. Width: 2,500 mm. Height: 1,800 mm. Kingpin height: 1,300 mm. Deck: Length: 8,000 mm. Width: 2,750 mm. Height: 500 mm. Deck thickness: 300 mm. Rear of trailer: Length: 5,600 mm. Width: 2,750 mm. Height: 1,050 mm. Dolly D-2. Year of manufacture: 2015. 10 t SAF axles. Unladen weight: 3,650 kg. Gross vehicle weight (GVW): 36,100 kg. Kingpin load: 16,100 kg. Air suspension. Tyres: 235/75R17.5, 70% remaining tread. German trailer! 4 units available! ID No.: 484. The General Terms and Conditions of Heinhuis apply to all advertisements, offers and quotations by Heinhuis, all contracts concluded by Heinhuis, and all negotiations preceding them. By responding in any form, you accept the applicability of the General Terms and Conditions of Heinhuis and confirm that you have taken note of these General Terms and Conditions. Our prices are net export prices. = Further information = Year of manufacture: 2015 Unladen weight: 22,250 kg Payload: 57,750 kg GVW: 80,000 kg Extendable body: Yes Price: On request = Company information = Isdpfx Asxrubqjfhoal For more information: WhatsApp:

Condition: new, empty load weight: 15,420 kg, maximum load weight: 61,080 kg, overall weight: 76,500 kg, axle configuration: > 3 axles, loading space length: 8,600 mm, loading space width: 2,540 mm, loading space height: 900 mm, tire size: 235/75/r17,5, color: grey, Equipment: ABS, Gooseneck: Gooseneck with rear bevel of approx. 750 mm x 10° 3 pairs of lashing rings Hardwood decking 30 mm thick Loading platform: Loading area in extendable design with rear bevel of approx. 500 mm x 8° 8 pairs of lashing rings can be folded outwards 1 pair of lashing rings lying in the front of the cargo bed Cut-outs in the outer frame of the cargo bed for attaching lashing straps Hardwood flooring approx. 48 mm thick, checker plate flooring over the axles Two-part steel ramps: A pair of galvanized two-part steel ramps approx. 2,750 + 1,400 x 800 mm with approx. 48 mm thick hardwood decking. Ramp with hydraulically folding and unfolding ramp sections, hydraulic lifting gear and hydraulically movable. Maximum load per pair: 50,000 kg. Seat posts: - JOST fifth wheels (mechanical) with 2-speed gearbox for 24t lifting load (50t test load). Axles and tires: BPW axles and suspension, 4th + 5th axle self-steering Technical axle load: 12,000 kg 4th and 5th axles with electro-magnetic reverse lock via reverse gear and manual activation Tires 235/75 R 17.5 3PMSF Brake system: Brake system in accordance with EU regulations with EBS-E (4S3M) Sockets and lighting: Electrical system in accordance with EU regulations, 24 volt lighting ASPÖCK-NORDIK (ASS3) ASPÖCK-UNIBOX on the front connection strip with 24N, 24S & 15-pin sockets Connection according to ISO 24N ISO-1185 24S ISO-3731 15 pole ISO-12098 Paint finish: First-class and durable corrosion protection of the standard shot-peened welded frame guaranteed by a 2-component (2K) zinc dust primer A high-quality 2-component (2K) top coat in a single color in MB 7350 nova grey Rear section metallized and painted in RAL 9010 (pure white) No metallic paint finish possible Steel construction: Steel construction made from high-strength fine-grained steels Steel grades: S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa) Accessories: One spare wheel with holder in front of the bulkhead 2" kingpin One galvanized steel bulkhead approx. 400 mm high Yellow-red air couplings on the galvanized connection strip at the front 2 restraining shoes with holder on the bulkhead Mounting in the rear area of the gooseneck for ALU docking lights A bracket for a rotating beacon at the rear of the trailer Galvanized supports under the bevel of the loading area White reflective tape in accordance with EU regulations on the sides, on the extension and red at the rear Electro-hydraulic unit at the rear under the cargo bed A holder for the warning signs, including a socket, on the gooseneck and on the rear panel on the left and right respectively Control valves for the ramps mounted on the right-hand side of the trailer A mud flap at the rear of the trailer Manual and description on USB stick 3.5" kingpin supplied loose Iaodpel Sl Izsfx Afhjl ALU drop sides and rear wall can be plugged onto the gooseneck approx. 2,440 x 400 mm (LxH) The rear galvanized stanchions are removable (length of the body approx. 2,560 mm) 3 pairs of WADER container pockets in the loading area for a 20' (30') or a 40' container 6 pairs of stanchion pockets for 100 x 50 mm stanchions in the outer frame of the cargo bed Galvanized extensions, extendable by approx. 230 mm per side Lift axle on the front axle with control by TEBS E depending on the current axle load and the current load status Square climbing rails 20 x 20 mm every 200 mm on the outer frame of the loading area slope On the chequer plates, above the kingpin and the load floor

Condition: used, empty load weight: 20,320 kg, maximum load weight: 46,180 kg, overall weight: 66,500 kg, axle configuration: > 3 axles, first registration: 01/2004, tire size: -, Year of construction: 2004, Ref: 2220 Extra low-bed trailer with 3 rear axles + 1 front axle (dolly). Maximum authorized weight: 66 T. Trailer with detachable gooseneck. Iodpfxjwcrzre Afhsal Extendable trailer (5 m). Trailer with 3 forced steering axles (and manual remote control). Trailer can be driven with or without a dolly. Total trailer length: 16.43 m + 5 m (extendable). Tare weight: 20,320 kg + 2,520 kg for a dolly. Gooseneck: L= 4.43 m. Extra low-bed: L= 7.5 m + 5 m (extendable). Height: 0.5 m. Trailer width: 2.74 m. Dock above rear axles: L= 4.5 m. H= 1.05 m. Dipper pit for excavator dippersticks. Rear ramps. Hydraulic (removable) and hydraulic ramp movement Tow tires: 285/70R19.5 Dolly tires: 235/75R17.5 Serial number: YA9TL366B04113968+122B4113969

Condition: used, functionality: fully functional, empty load weight: 10,700 kg, first registration: 06/2015, Year of construction: 2015, FAYMONVILLE Max Trailer F-S44-1A1Y Length: 13,050 mm Width: 2,550 mm Front tire: 235/75R17.5 Rear tire: 235/75R17.5 Wheelbase: 1,360 mm Total permissible weight: 40,000 kg Payload: 29,300 kg Empty weight: 10,700 kg Equipment: Cable winch 2" kingpin Operation via 2-pin NATO connector 4 SAF axles 2x steerable ABS Rear support ESB Hydraulic loading ramps (steel ramps) Iaodjvx R Nhjpfx Afhol Telescopic Drum brake

Condition: new, maximum load weight: 38,400 kg, overall weight: 48,000 kg, axle configuration: 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our entire fleet of vehicles—including those available for immediate or short-term delivery—on our website. Extract from the equipment list. Complete equipment details available upon request. Cargo area: * Extendable cargo area with pneumatically operated locking mechanism * Cargo area with approx. 30 mm thick wooden floorboards * 7 pairs of outward-folding lashing rings (LC 5,000 daN) * 3 pairs of outward-folding lashing rings (LC 10,000 daN) * Cut-outs in the outer frame of the cargo area for attaching tensioning straps (LC 2,000 daN) Landing gear: * JOST mechanical landing legs with 2-speed gearbox, 24t lifting capacity (50t test load) Tyres: * 385/65 R 22.5 tyres Iaedpfx Asxl Nf Djfhol Axle: * BPW axles and suspension, all axles hydro-mechanically forced-steered * With disc brakes * Technical axle load: 10,000 kg (ET 0) * Air suspension with lift and lower valve Brake system: * WABCO brake system in accordance with EU regulations with EBS-E (2S2M), without connecting lines to the tractor unit Paintwork: * High-quality 2-component (2K) topcoat in single-tone RAL 3002 Carmine Red Accessories: * Steering from front and rear, operated via cable remote control with push buttons, with single-track axle monitoring (without installation in towing vehicle) * Electro-hydraulic power unit * 4 wheel chocks with holders on the front bulkhead * 2-inch king pin * Galvanised connection strip at the front with yellow-red air couplings * Mounting bracket for rotating beacon at the rear of the trailer * 10 pairs of stake pockets for plug-in stakes approx. 100 x 50 mm in the outer frame of the cargo area * 1 spare wheel holder under the cargo area on the right-hand side (no spare wheel included) * Load gauge for determining axle loads, including load diagram Including special accessories: * Galvanised steel front wall (EN12642-XL), approx. 1,600 mm high * 6 pairs of WADER container pockets in the cargo area for 1 x 20' container, 2 x 20' containers or 1 x 40' container; additional locking point in the extension for a 45' container * 4 crosswise pairs of stake pocket rails mounted in the cargo area for plug-in stakes approx. 100 x 50 mm * Storage for up to 9 pairs of plug-in stakes, screwed to the inside of the front wall * Boarding ladder mounted left and right in the direction of travel * INOX toolbox approx. 1,200 x 460 x 550 mm, mounted at the front under the cargo area on the left in the direction of travel * Additional INOX toolbox approx. 1,200 x 460 x 550 mm, under the cargo area on the left in the direction of travel * Cargo area with approx. 30 mm thick wooden floorboards framed in omega profiles * Lift axle on the front axle with control via TEBS E * BEKAMAX (Pico) centralized lubrication system with standard grease NLGI-2 * 2 LED reversing lights mounted on the rear panel * 2 pairs of ferry rings under the gooseneck and 2 pairs at the rear * HRM Metallisation (High Resistance Metallisation)

Condition: new, empty load weight: 9,600 kg, maximum load weight: 53,400 kg, overall weight: 63,000 kg, axle configuration: > 3 axles, loading space length: 12,400 mm, loading space width: 2,540 mm, loading space height: 1,340 mm, suspension: air, tire size: 385/65 R22.5, color: grey, Equipment: ABS, Loading area: -Loading area with approx. 30 mm thick hardwood floor -10 pairs of lashing rings can be folded outwards Seat posts: -JOST seat posts with 2-speed gearbox for 24 t lifting load Axles and tires: -BPW axles, techn. 10,000 kg, first axle rigid, all other axles hydro-mechanically forced steered, mounted on turntable -Air-sprung with lifting and lowering valve -axle tool -385/65 R22.5 tires Brake system: -WABCO brake system in accordance with EU regulations with EBS-E (4S3M) Steel construction: -steel construction made of high-strength fine-grained steels -Steel grades: -S355J2+N/S355MC -S690QL/S700MC Electrical system: -Electrical system in accordance with EU regulations, 24 volt lighting -ASPÖCK UNIBOX on the front connection strip with 24N, 24S & 15-pin sockets Connection in accordance with ISO: 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Paintwork: -First-class and durable corrosion protection of the standard shot-blasted welded frame guaranteed by a 2-component zinc dust primer A high-quality 2-component top coat in a single color in nova grey -Rear part metallized and painted in RAL 9010 Accessories included: -Loading area with approx. 30 mm thick hardwood floor -2" kingpin -One galvanized steel end wall approx. 1,200 mm high EN12642-XL -Yellow-red air couplings on the galvanized connection strip at the front -4 restraining shoes with holder on the front wall -Storage for 1,000 mm stanchions in the rear central support -On the gooseneck and on the rear panel on the left and right, one bracket each for the warning signs including socket -Reverse steering can be operated from the front and rear via cable remote control using pushbuttons, with tracking control of the axles -Electric hydraulic unit -White reflective tape in accordance with EU regulations on the side of the trailer and red at the rear -12 pairs of stanchion pockets for 100 x 50 mm stanchions in the outer frame of the cargo bed Isdpfxorq Dlfs Afhjal -European reflector plates at the rear of the trailer -One bracket for a rotating beacon at the rear of the trailer -One mud flap at the rear of the trailer -Manual and description on USB stick -BEKAMAX (Pico) central lubrication system with NLGI-2 standard grease and removable protection around the pump -TPMS tire pressure monitoring system: -For correct display, the motor vehicle must be able to transmit and display this data -Lift axle on the front axle with control by TEBS E depending on the current axle load and the current load status -Radio remote control for steering in addition to the cable remote control, with indicator lights on the receiver for tracking control -5 pairs of stanchion pocket rails, mounted transversely in the cargo bed, for 100 x 50 mm stanchions -Speed stickers 80 km/h at the rear and on both sides -Adjustable access ladder mounted on the left and right in the direction of travel -2 reversing lights mounted on the rear panel -Load manometer for determining the axle loads including load diagram HRM metallization of the outer frame Complete steel construction shot-blasted, then the defined visible surfaces hot-finished in metallization with ZINACOR 850 (zinc 85% - aluminium 15%)

Condition: new, maximum load weight: 37,680 kg, overall weight: 50,960 kg, axle configuration: > 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete inventory of vehicles, including those available for immediate and short-term delivery, on our website. Extract from the equipment features. Complete specification available on request. Gooseneck * With approximately 30 mm thick hardwood flooring. Gooseneck with straight rear section * 3 pairs of lashing rings (LC 5,000 daN) Loading Area * Extendable design * 5 pairs of outward-folding lashing rings (LC 5,000 daN) * 3 pairs of outward-folding lashing rings (LC 10,000 daN) * 1 pair of recessed lashing rings at the front of the loading area (LC 10,000 daN) * Cutouts in the outer frame of the loading area for attaching tension straps (LC 2,000 daN) * Approx. 48 mm thick hardwood flooring, treadplate covering above the axles Landing Gear * JOST mechanical landing gear with 2-speed gearbox, lifting capacity approx. 24 t (test load approx. 50 t) Tyres * 205/65 R 17.5 Axles * BPW axles and suspension * 1st axle fixed, all other axles hydro-mechanically forced-steered * Air suspension with lift and lower valve Ijdpjv Etx Eefx Afhjal Brake System * In accordance with EU regulations, with EBS-E (4S3M) without connection lines to the tractor unit Steel Construction * Made of high-strength fine-grained steels * Steel grades: S355J2+N/S355MC (yield strength 355 MPa), S690QL/S700MC (yield strength 690 MPa) Paintwork * Premium and durable corrosion protection for the standard shot-blasted welded frame, guaranteed by a two-component (2K) zinc dust primer * High-quality two-component (2K) top coat, single colour RAL 3002 carmine red * Rims in silver Accessories Included * 2" king pin * Galvanised steel front wall, approx. 400 mm high * Yellow-red air couplings on galvanised front connection strip * 4 chocks with holder on the front wall * Spare wheel holder in front of the front wall * Electro-hydraulic unit * Steering from the front and rear via cable remote control with push buttons, including single-track control of the axles (without installation in the tractor unit) * European reflective signs (red-yellow) at the rear of the trailer * Yellow reflective tape according to EU regulations on sides, extensions, and rear of the trailer * Bracket for warning signs including socket, left and right on the gooseneck and rear plate * Bracket for rotating beacon at the rear of the trailer * Galvanised foldable support legs under the loading area's chamfer * Load gauge for determining axle loads including load diagram * 7 pairs of WADER container pockets for: 1x 20' or 1x 40' container on the loading area, 1x 40' container over the gooseneck, or 2x 20' containers * Support block with 1 pair of WADER container pockets, fifth wheel load approx. 20,000 kg * 7 pairs of stake pockets for approx. 100 x 50 mm plug-in stakes in the outer frame of the loading area * Galvanised, extendable width extensions, approx. 230 mm per side * Sliding hook-in rails for aluminium loading ramps at the rear of the vehicle * 1 pair of recessed lashing rings along the central beam at the rear of the loading area (LC 10,000 daN) * 2 pairs of ferry rings under the gooseneck and 2 pairs at the rear * BEKAMAX (Pico) central lubrication system with standard grease NLGI-2 and removable pump protection * 2 LED reversing lights mounted at the rear * Acoustic reversing warning signal * HRM Metallisation (High Resistance Metallisation)

Condition: new, maximum load weight: 73,540 kg, overall weight: 102,000 kg, axle configuration: > 3 axles, Equipment: ABS, You can find our complete inventory of vehicles, including units available immediately and at short notice, on our website. Overview of equipment. Full equipment list available on request. Neck (gooseneck): * Hydraulically liftable/lowerable and removable gooseneck, length approx. 3,650 mm * 2 pairs of fold-out lashing rings (LC 5,000 daN) * 2 pairs of lashing rings on the gooseneck (LC 10,600 daN) * 1 pair of lashing rings in the center section of the gooseneck (LC 10,600 daN) * For 6x4 or 8x4 2-axle tractor units Compact front bogie: * Hook pick-up front and rear, length: approx. 2,200 mm * Bogie width: approx. 2,850 mm Excavator deck: Telescopic excavator deck with drive-over deck hooks at the front and bolt-lug coupling at the rear * Basic width: approx. 2,850 mm * Length: approx. 6,650 mm * Beam height: approx. 400 mm * Beam width: approx. 1,350 mm * Loading height approx. 550 mm with ground clearance of approx. 150 mm 4-axle rear bogie: * Mechanical bolt-lug coupling at the front for mounting a lowbed * Rear crossmember bogie width: approx. 2,850 mm * Bogie length: approx. 5,480 mm Pendulum axles, all axles hydro-mechanically steered * Technical axle load: 14,640 kg each (62 km/h) * Hydraulic axle compensation Tyres: * Front bogie: * 8 x manufacturer’s choice (M+S) 285/70 R19.5 * Rear bogie tyres: * 16 x manufacturer’s choice (M+S) 285/70 R19.5 * Load index 150/148J Ijdpfx Afjxbmplshoal Paintwork: * Complete steel construction is automatically blasted with a blasting wheel system after welding. Second blasting with corundum for optimal adhesion of the coating system * Full chassis HRM-metallized with ZINACOR 850 (85% zinc/15% aluminum) for maximum corrosion protection * Final painting with two coats of 2K topcoat, single-color in RAL 3002 carmine red, according to RAL system 841GL Including the following accessories: * Steel front wall, approx. 400 mm high * Plug-in ALU sidewalls and rear wall, approx. 400 mm high, anodized version, fitted on the gooseneck * 3.5 inch kingpin * Truck hydraulic connection with flow control (20 l/min) * Support gallows for supply lines, tractor unit tank must be at least 80 l * with MAX Trailer couplings, otherwise customer to supply coupling parts ex works * BEKA-MAX central lubrication for one gooseneck with standard grease NLGI-2 * Tool kit Art No. 612452 * Multi-coupling hydraulic connections on the gooseneck * Front bogie with separate air connection for air screwdriver * BEKA-MAX central lubrication for one 2-axle bogie with standard grease NLGI-2 * One 7-pin socket left and right rear on the front bogie for warning signs * Screw-in facility (ø approx. 40 mm) every approx. 500 mm on the outside of the upper flange of the outer tube of the excavator deck for bolt-on rings (LC 16,000 daN) * Foldable width extensions with steel covers, adjustable in width from approx. 2,850 mm to approx. 3,250 mm * BEKA-MAX central lubrication for one 4-axle bogie with standard grease NLGI-2 * At the rear bogie, a socket for the cable remote control of the steering * Rear bogie with trough * Two INOX toolboxes, approx. 855 x 340 x 390 mm, mounted left and right on the gooseneck * 1-cylinder Hatz diesel engine (Silent Pack) with electric starter and starter battery * Radio remote control: * Operation of the powerpack, start/stop of the diesel engine * Control of the steering, in addition to the cable remote control * One LED work light each left and right at the end plate of the gooseneck with...

Condition: new, maximum load weight: 48,010 kg, overall weight: 66,000 kg, axle configuration: 3 axles, Equipment: ABS, You can find our entire stock of vehicles, including those available immediately and at short notice, on our website. Extract from the specifications. Full equipment list available upon request. Gooseneck: * Gooseneck in SNT design to optimize loading platform length, approx. 3,700 mm long * Gooseneck hydraulically liftable/lowerable and detachable * For tractors: 6 x 4 or 8 x 4 Low bed: * Low bed with external beams, extendable design, SUPER LOW design, approx. 7,550 mm long * Low bed with fixed hardwood floor, approx. 40 mm thick, with mechanical locking * Supply lines are protected within the extendable beams and automatically adapt to the respective low bed length * 7 pairs of lashing rings, foldable to the outside (approx. LC 10,000 daN) * 6 pairs of threaded blocks on the inner beams for mounting bolted RUD rings Rear chassis: * Rear chassis with closed outer frame, chequer plate covering, and continuous prism-shaped excavator recess, approx. 1,450/900 x 505 mm, open at the rear * 2 pairs of lashing rings, foldable to the outside (approx. LC 10,000 daN) * 1 pair of lashing rings, lying flat in the recess (approx. LC 10,000 daN) * 2 pairs of lashing rings, lying flat in the recess (approx. LC 16,000 daN) * 2 pairs of stake pockets for plug-in stakes, approx. 100 x 50 mm in the outer frame Ijdpfx Afexbmprshoal PENDLE AXLE: * PENDLE AXLE, all axles hydro-mechanically forced-steered * Hose rupture valve on axle compensation cylinder with automatic reset function * Hydraulic cylinders with shut-off valves and locking pins to secure in the raised position * Technical axle load: 12,000 kg each * Hydraulic axle compensation * Axle tool Tyres: * Tyres 245/70 R 17.5 3PMSF – brand at our discretion * Load index (146/146F) Brake system: * Wabco brake system according to EU regulations with EBS-E (2S2M), without connection lines to the tractor unit Paintwork: * Entire steel structure automatically blast-cleaned after welding using a shot blasting unit * Second blast treatment with corundum for optimum coating adhesion * HRM metallization of the entire vehicle chassis with ZINACOR 850 (85% zinc/15% aluminum) to guarantee the best corrosion protection * Final paint finish with 2 coats of 2K topcoat, single-color in RAL 3002 Carmine Red according to RAL system 841GL Including the following accessories: * Preparation for installation of bolted container placements for 1x 20' or 1x 40' container on the external beams * Without container locks * 3.5 inch kingpin * One galvanized steel front wall, approx. 400 mm high * Remote-controlled steering from the front and rear via cable remote with push buttons, with axle tracking control (without installation on the tractor unit) * Electro-hydraulic unit * On the gooseneck, removable aluminum side and rear walls, approx. 2,000 x 400 mm (L x H) * The rear galvanized plug-in stakes are removable (superstructure length approx. 2,120 mm) * Hydraulic connections from the gooseneck to the low bed via multi-coupling instead of screw couplings (no guarantee on seals) * Separate air connection with air gun on gooseneck * 7 pairs of stake pockets for plug-in stakes approx. 100 x 50 mm in the outer frame of the loading area * One INOX toolbox, approx. 1,350 x 400 x 400 mm, on the gooseneck * 2 pairs of boltable lashing rings M20 (LC 5,000 daN) * 2 pairs of boltable RUD rings VLBG-4 M24 (LC 8,000 daN) * Folding extensions, approx. 230 mm per side, widening planks made of hardwood. The maximum load is distributed on an area of appr

Condition: new, maximum load weight: 45,820 kg, overall weight: 58,000 kg, axle configuration: > 3 axles, Equipment: ABS, You can find our entire inventory of immediately and short-term available vehicles on our website. Excerpt from the features. Complete list of features available on request. Gooseneck: * Gooseneck with beveled front corners approx. 45° and rear bevel approx. 750 mm x 10° * 3 pairs of lashing rings (LC 5,000 daN) * Hardwood flooring approx. 30 mm thick Extendable loading platform: * Extendable loading platform with rear bevel approx. 1,000 mm x 8° * 5 pairs of folding lashing rings on the outside (LC 5,000 daN) * 3 pairs of folding lashing rings on the outside (LC 10,000 daN) * 1 pair of flat-mounted lashing rings at the front of the loading area (LC 10,000 daN) * Cutouts in the outer frame of the loading platform for attaching tie-down straps (LC 2,000 daN) * Hardwood flooring approx. 48 mm thick, over axles with checker plate Axles: * BPW axles and suspension * 1st axle fixed, all other axles hydro-mechanically forced-steered * Technical axle load: 12,000 kg each * Air suspension with lifting and lowering valve * Axle tools Tires: * 245/70 R 17.5 3PMSF tires, load index (146/146 F) * Brand of our choice * TPMS tire pressure monitoring system according to ECE R 141 * Data transmission to the tractor unit is via standardized EBS interface per ISO 11992 * For correct display, the tractor unit must be able to transmit and display this data Landing legs: * JOST landing legs (mechanical), 2-speed gearbox for approx. 24 t lifting capacity (approx. 50 t test load) Brake system: * Wabco braking system in accordance with EU regulations, with EBS-E (4S3M), without connecting lines to the tractor unit Paintwork: * Complete steel construction is automatically blasted after welding by shot blast machine * Second blasting with corundum for optimal coating adhesion * Final paintwork: 2 coats of 2K topcoat, solid color in RAL 3002 Carmine Red per RAL system 841GL * Rims in silver gray * Rear panel metallized and painted in RAL 9010 (pure white) * No metallic paint available * Paint system tested by salt spray test according to ISO 9227-NSS * Cavity sealing with special wax Steel construction: * Steel structure made from high-strength fine-grained steels Ijdpoxbmpfsfx Afhsal * Steel grades: S355J2+N/S355MC (yield strength 355 MPa), S690QL/S700MC (yield strength 690 MPa) Electrical system: * Electrical system according to EU regulations * Lighting 24 volt ASPÖCK-NORDIK (ASS3) * All LED side marker lights flash in sync with the indicators * ASPÖCK-UNIBOX at the front connection strip with 24N, 24S & 15-pin sockets according to ISO. * 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Includes the following additional equipment: * 2-inch king pin * Galvanized steel front wall, approx. 400 mm high * At the galvanized front connection strip, yellow-red air couplings * Electro-hydraulic unit * Remote steering control, operated from both front and rear via cable remote with push buttons, with single-track axle control (without installation in the tractor unit) * Galvanized folding supports under the rear ramp of the loading platform * 1 pair of recessed lashing rings along the main longitudinal beam at the rear ramp (LC 10,000 daN) * On the gooseneck, removable aluminum side and rear walls, approx. 2,440 x 400 mm (L x H) * The rear galvanized socket stakes are removable. (Upper body length approx. 2,560 mm) * 1 galvanized toolbox, integrated into the sloped gooseneck * 3 pairs of WADER container pockets in the loading platform for one 20' (30?) or one

Condition: new, maximum load weight: 39,670 kg, overall weight: 50,960 kg, axle configuration: > 3 axles, Equipment: ABS, You can find our complete range of immediately and short-term available vehicles on our website. Extract from the equipment list. Full equipment details available on request. Gooseneck: * Gooseneck with hardwood flooring approx. 30 mm thick * Rear of gooseneck in straight design * 3 pairs of lashing rings (LC 5,000 daN) Loading Area: * Extendable loading area * 5 pairs of fold-out lashing rings to the outside (LC 5,000 daN) * 3 pairs of fold-out lashing rings to the outside (LC 10,000 daN) * 1 pair of recessed lashing rings at the front of the loading area (LC 10,000 daN) * Cutouts in the outer frame of the loading area for attaching tension straps (LC 2,000 daN) * Hardwood flooring approx. 48 mm thick, checker plate covering over the axles Landing Legs: JOST landing legs (mechanical) with 2-speed gearbox for approx. 24 t lifting capacity (approx. 50 t test load) Axles: * BPW axles, two rigid axles, two self-steering axles * Air suspension with lift/lower function * Self-steering axles with electromagnetic reverse lock, activated via reverse gear or manually * Drum brakes * Axle tool kit Tyres: * 205/65 R 17.5 * Brand of our choice * TPMS tyre pressure monitoring system according to ECE R 141 * Data transfer to the tractor unit via the standardised EBS interface as per ISO 11992 * For correct display, the tractor unit must be able to transmit and display these data Brake System: * Brake system in accordance with EU regulations with EBS-E (4S3M) without connection lines to the tractor unit Steel Structure: * Steel construction made of high-strength fine-grain steels * Steel grades: S355J2+N/S355MC (yield strength 355 MPa) S690QL/S700MC (yield strength 690 MPa) Paintwork: * Complete steel structure automatically blasted after welding using a shot blast system * Second blasting with corundum for optimal coating adhesion * HRM metallization of the entire chassis with ZINACOR 850 (85% zinc/15% aluminum) for best corrosion protection * Final coating with 2 x 2K topcoat, solid colour in RAL 3002 Carmine Red, according to RAL system 841GL * Wheels in silver * Rear section metallised and painted in RAL 9010 (Pure White) * Metallic paint not available * Paint finish tested with salt spray test according to ISO 9227-NSS * Cavities sealed with special wax Electrical System: * Electrical system in compliance with EU regulations, 24 Volt ASPÖCK-NORDIK (ASS3) lighting * All LED side marker lights blink together with the indicator Iaodoxarlvopfx Afhel * ASPÖCK-UNIBOX at the front connection strip with 24N, 24S & 15-pin sockets according to ISO; 24N ISO-1185, 24S ISO-3731, 15-pin ISO-12098 Accessories included: * 2-inch king pin * One spare wheel holder in front of the bulkhead * Yellow-red air couplings at the galvanised connection strip up front * Galvanised folding supports beneath the loading area bevel * One galvanised steel bulkhead (EN12642-XL), approx. 1,600 mm high * On the gooseneck, plug-in aluminium side and rear boards, approx. 2,440 x 400 mm (L x H) * The rear galvanised plug-in stanchions are removable (body length approx. 2,560 mm) * Support bracket with 1 pair of WADER container locks. Fifth-wheel load approx. 20,000 kg * 7 pairs of WADER container locks for 1x 20' container in the loading area * 1x 40' container in the loading area, 1x 40' container on the gooseneck, 2x 20' container * 7 pairs of stake pockets for 100 x 50 mm plug-in stanchions in the outer frame of the loading area * One galvanised bracket running across under...

Condition: new, maximum load weight: 38,400 kg, overall weight: 48,000 kg, axle configuration: 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory, including immediately and short-term available vehicles, on our website. Iaedpew Tpr Iofx Afhjl Excerpt from the specifications. Full specification available on request. Loading area: * Extendable loading platform with pneumatically operated locking mechanism * Loading area with approx. 30 mm thick wooden planks * 7 pairs of outward-folding lashing rings (LC 5,000 daN) * 3 pairs of outward-folding lashing rings (LC 10,000 daN) * Cut-outs in the outer frame of the platform for hooking in tension straps (LC 2,000 daN) Landing legs: * JOST mechanical landing legs with 2-speed gearbox, approx. 24 t lifting capacity (approx. 50 t test load) Tyres: * Tyres: 385/65 R 22.5, manufacturer at our discretion * TPMS tyre pressure monitoring system in accordance with ECE R 141. Data transmission to the truck is via the standardized EBS interface as per ISO 11992. For proper display, the truck must be capable of receiving and showing this data. Axle: * BPW axles and suspension * All axles hydromechanically forced-steered * Disc brakes * Technical axle load: 10,000 kg each (offset 0) * Air suspension with raise/lower valve * Axle tools Brake system: * WABCO brake system in accordance with EU regulations, EBS-E (2S2M) without connection lines to the tractor unit Steel construction: * High-strength fine-grain steel construction * Steel grades: S355J2+N/S355MC (yield strength 355 MPa), S690QL/S700MC (yield strength 690 MPa) Electrical system: * Electrical system in accordance with EU regulations * LED lighting 24 Volt ASPÖCK-NORDIK (ASS3) * All LED side marker lights flash together with indicators * ASPÖCK-UNIBOX at the front connection bar with 24N, 24S, and 15-pin sockets according to ISO: 24N ISO-1185, 24S ISO-3731, 15-pin ISO-12098 Paintwork: * Complete steel structure automatically shot-blasted after welding * Second blasting with corundum for optimal coating adhesion * Final painting with two coats of 2-component topcoat, single color, RAL 3002 Carmine Red according to RAL system 841GL * Rims in silver grey * Rear section metallized and painted RAL 9010 (Pure White) * Metallic paint not available * Paint finish tested in salt spray test according to ISO 9227-NSS * Cavity sealing with special wax Accessories: * Remote steering from front and rear via cable remote control with push buttons, with axle tracking monitoring (without installation in the tractor unit) * Electro-hydraulic unit * 4 wheel chocks with holders on the front wall * 2" kingpin * Yellow-red air couplings at the galvanized front connection bar * At gooseneck and rear, left and right, brackets for warning panels, including sockets * 10 pairs of stake pockets for approx. 100 x 50 mm plug-in stakes in the external frame of the loading platform * One galvanized steel front wall (EN12642-XL), approx. 1,600 mm high * 6 pairs of WADER container pockets in the loading area, for 1 x 20' container, 2 x 20' containers, or 1 x 40' container; an additional locking position is provided in the extension for a 45' container * 4 pairs of transverse stake pocket strips in the loading area for approx. 100 x 50 mm plug-in stakes * Storage for max. 9 pairs of plug-in stakes bolted inside to the front wall * Boarding ladder mounted left and right in the direction of travel * One INOX toolbox, approx. 1,200 x 460 x 550 mm, mounted front left under the loading platform * An additional INOX toolbox, approx. 1,200 x 46...

Condition: new, maximum load weight: 33,865 kg, overall weight: 48,000 kg, axle configuration: 3 axles, Equipment: ABS, You can find our complete range of vehicles, including those available for immediate delivery or on short notice, on our website. Below is an excerpt from the specification. The full equipment list is available upon request. Gooseneck: * Gooseneck with front corners chamfered approx. 45° and a rear bevel approx. 750 mm x 10° * 3 pairs of lashing rings (LC 5,000 daN) * Hardwood flooring approx. 30 mm thick Load area: * Double extendable design with rear bevel approx. 500 mm x 8° * 6 pairs of folding external lashing rings (LC 5,000 daN) * 4 pairs of folding external lashing rings (LC 10,000 daN) * 1 pair of recessed lashing rings at the front of the loading area (LC 10,000 daN) Iaedpfx Aow Tprzsfhol * 1 intermediate table approx. 250 mm * Hardwood flooring approx. 48 mm thick, over axles with checker plate covering * Cut-outs in the external frame of the loading platform for attaching tie-down straps (LC 2,000 daN) Axles: * BPW axles and suspension, all axles forced-steered hydro-mechanically * Design axle load: 12,000 kg each * Air suspension with lift and lower valve * Axle tools included Tyres: * 245/70 R 17.5, load index (146/146 F) * Brand of our choice Landing legs: * JOST mechanical landing legs with 2-speed gearbox for approx. 24 t lifting capacity (approx. 50 t test load) Braking system: * Braking system according to EU regulations with EBS-E (2S2M) without connection lines to the tractor unit Paintwork: First-class and durable corrosion protection * High-quality, one-colour 2-component (2K) topcoat in RAL 3002 carmine red * Rear section metallized and coated in RAL 9010 (pure white) Steel Structure: Steel construction from high-strength fine grain steels. * Steel grades: S355J2+N/S355MC (yield strength 355 MPa), S690QL/S700MC (yield strength 690 MPa) Electrical system: * Electrical system according to EU regulations * 24 Volt lighting ASPÖCK-NORDIK (ASS3) * ASPÖCK-UNIBOX at the front connection strip with 24N, 24S & 15-pin sockets, compliant with ISO. 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Including the following additional equipment: * 2-inch kingpin * Galvanized steel front wall, approx. 400 mm high * Yellow-red air couplings at the galvanized front connection strip * Spare wheel carrier in front of the front wall * Electro-hydraulic unit * Rear and front steering via cable remote control with push-buttons, with single-track monitoring of the axles (without installation in the tractor unit) * Mount at the rear of the gooseneck for aluminum loading ramps * Removable aluminum ramp hanging rail at the rear of the vehicle * Galvanized folding supports beneath the slope of the load area * On the gooseneck: plug-in aluminum side boards and rear board, approx. 2,440 x 400 mm (L x H) * The rear galvanized stanchions are removable (body length approx. 2,560 mm) * One galvanized toolbox, integrated in the chamfered gooseneck * 4 pairs of WADER container pockets in the loading area for one 20', two 20', one 40' or one 45' container * 8 pairs of stanchion pockets (approx. 100 x 50 mm) in the external frame of the loading platform * Galvanized extensions, extendable by approx. 230 mm per side * Adjustable hanging rails for aluminum ramps at the rear of the vehicle * 2 pairs of ferry rings under the gooseneck and 2 pairs at the rear * Central lubrication system with 2 BEKAMAX (Pico) pumps, filled with standard grease NLGI-2 and removable pump guard * 2 LED reversing lights mounted on the rear panel * HRM Metallization (High Resistance Metallisa

Condition: new, maximum load weight: 61,050 kg, overall weight: 73,000 kg, axle configuration: > 3 axles, Equipment: ABS, You can find our complete vehicle inventory, including vehicles available immediately or at short notice, on our website. Excerpt from the equipment. Full equipment list available upon request. Loading Platform: * Loading platform with approx. 30 mm thick hardwood floor * 10 pairs of folding external lashing rings (LC 10,000 daN) Landing Legs: * JOST landing legs (mechanical) with two-speed gearbox for approx. 24 t lifting capacity (approx. 50 t test load) Axles and Suspension: * BPW axles, technically rated at 12,000 kg each * 1st axle steered, 2nd axle fixed, all other axles hydro-mechanically forced steered, mounted on turntable * Air suspension with raise/lower valve * Axle tools Tyres: * Tyres 445/65 R 22.5 169K – manufacturer of our choice TPMS * TPMS tyre pressure monitoring system according to ECE R 141 * Data transmission to tractor unit via standardised EBS interface according to ISO 11992 * For correct display, the tractor unit must be able to process and display this data Brake System: * Wabco brake system as per EU regulations with EBS-E (4S/3M) without connecting lines to the tractor unit Electrical System: * Electrical system in accordance with EU regulations * Lighting 24V ASPÖCK-NORDIK (ASS3) * All LED side marker lights flash with the indicator * ASPÖCK-UNIBOX at the front connection rail with 24N, 24S & 15-pin sockets according to ISO. 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Steel Structure: * Steel construction made of high-strength fine-grained steels * Steel grades: S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa) Iodpfx Aow Tpr Uefhjal Paintwork: * Entire steel construction automatically blasted after welding using a shot-blasting machine * Second blasting with corundum for optimal coating adhesion * HRM metallisation of the entire vehicle chassis with ZINACOR 850 (85% zinc/15% aluminium) to ensure optimal corrosion protection * Final coating with 2 layers of 2K topcoat, single color in RAL 3002 Carmine Red as per RAL System 841GL * Rear section metallised and painted in RAL 9010 (Pure White) * Rims in silver grey * Paint system tested by salt spray test according to ISO 9227-NSS * Cavities sealed with special wax * Metallic paint finish not possible Including the following accessories: * Loading platform with approx. 30 mm thick hardwood floor * 2-inch kingpin * One galvanized steel front wall (EN12642-XL), approx. 1,200 mm high * Yellow-red air couplings on the galvanized front connection rail * Storage for approx. 1,000 mm long insertable stanchions in the rear central beam * At the gooseneck and rear plate, left and right, one bracket each for warning signs including socket * Remote steering from front and rear via cable remote control with push-buttons, with single-track monitoring of the axles (no installation in the tractor unit) * Electro-hydraulic unit * 13 pairs of stanchion pockets for insertable stanchions approx. 100 x 50 mm in the outer frame of the loading platform * Lift axle on 1st and 2nd axle with control via TEBS E depending on current axle load and loading status * 7 pairs of galvanized insertable stanchions, approx. 100 x 50 mm, approx. 1,000 mm high * 5 pairs of crosswise stanchion pocket strips mounted on the loading platform for stanchions approx. 100 x 50 mm * 2 pairs of WADER container pockets in the loading platform, for 1x10' * 1 shunting coupling with reinforcement bolted to the rear crossmember * Central lubrication system BEKAMAX (Pico) with standard grease NLGI-2

Condition: new, maximum load weight: 38,140 kg, overall weight: 48,000 kg, axle configuration: 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory, including vehicles available immediately and at short notice, on our website. Excerpt from equipment. Full equipment details available on request. Gooseneck: - Gooseneck with front corners chamfered approx. 45° and rear bevel approx. 750 mm x 10° - 3 pairs of lashing rings (LC 5,000 daN) - Hardwood flooring, approx. 30 mm thick Loading area: - Telescopic loading area with rear incline approx. 1,000 mm x 8° Iodpfxow Tpq Ds Afheal - Between 1st and 2nd axle: one pair of fixed wheel recesses, approx. 1,610 x 970 x 400 mm (L x W x D) - Incl. 3-piece removable galvanized cover over wheel recesses (width approx. 670 mm – max. point load 5 t / pc.) - 1 pair of flat lashing rings at the front of the loading area (LC 10,000 daN) - 4 pairs of outward folding lashing rings (LC 5,000 daN) - 3 pairs of outward folding lashing rings (LC 10,000 daN) - Cutouts in the outer frame for attaching tie-down straps (LC 2,000 daN) Landing legs: - JOST landing legs (manual) with 2-speed gearbox for 24 t lifting capacity (50 t test load) Tyres: - Tyres 235/75 R17.5 3PMSF, make at our discretion - TPMS tyre pressure monitoring system in accordance with ECE R 141 - Data transfer to the towing vehicle via standardised EBS interface as per ISO 11992 - For correct display, the towing vehicle must be able to receive and display this data Axles: - BPW axles and suspension, 2 axles rigid, 3rd axle self-steering - Technical axle load: 12,000 kg - Electromagnetic reverse lockout activated automatically when reversing and manually - Air suspension with lifting and lowering valve. Axle tools Braking system: - WABCO braking system according to EU regulations with EBS-E (2S2M) without piping to the tractor unit Electrical system: - Electrical system per EU regulations - LED lighting 24 Volt ASPÖCK-NORDIK (ASS3) - All LED side marker lights flash with the indicator - ASPÖCK-UNIBOX at front connection strip with 24N, 24S & 15-pin sockets, according to ISO; 24N ISO-1185, 24S ISO-3731, 15-pin ISO-12098 Steel construction: - Steel structure made of high-strength fine-grained steels - Steel qualities: S355J2+N/S355MC (yield strength 355 MPa), S690QL/S700MC (yield strength 690 MPa) Paintwork: - Complete steel structure automatically shot-blasted after welding in a wheel-blasting system - Second shot-blasting with corundum for optimum coating adhesion - HRM metallization of entire chassis with ZINACOR 850 (85% zinc/15% aluminium) for maximum corrosion protection - Final painting with 2 layers of 2K topcoat, single-colour in RAL 3002 Carmine Red, rear section metallized and painted in RAL 9010 Pure White - Metallic finish not available - Paint structure tested in salt spray test according to ISO 9227-NSS - Internal cavities sealed with special wax Including the following accessories: - On the gooseneck and rear, left and right, one holder for warning signs each, including socket - Spare wheel holder in front of the front wall (without spare wheel) - 2-inch king pin - Galvanized steel front wall, approx. 400 mm high - Yellow-red air couplings on the galvanized front connection bar - Galvanized folding supports under the inclination at the rear of the loading area - A hardwood crash protection strip at the rear wall from gooseneck to the loading area - 1 pair of recessed lashing rings along the central beam at the rear inclination (LC 10,000 daN) - Aluminium drop sides and tailgate on the gooseneck

Condition: new, maximum load weight: 50,400 kg, overall weight: 65,000 kg, axle configuration: > 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory, including units available immediately and at short notice, on our website. Excerpt from the equipment list. Full equipment specifications available on request. GOOSENECK Iedpfxjtx Nwnj Afhoal * Gooseneck in SNT design to optimize loading platform length, approx. 3,700 mm long, with rear bevel approx. 1,000 mm x 10° * For tractor units: 4 x 2, 6 x 2, and 6 x 4 * Removable steel front wall, approx. 400 mm high * ASPÖCK-UNIBOX on the front connector strip with sockets * 3 kW electro-hydraulic unit for controlling hydraulic operations, excluding hydraulic winches * 1 pair of removable aluminum side boards, approx. 400 mm high, anodized finish * 1 removable aluminum tailgate, approx. 400 mm high, anodized finish * Approx. 40 mm thick hardwood floor above gooseneck, checker plate floor above king pin * 2-inch king pin * Rear section of gooseneck prepared for aluminum drive-on ramps * Round NATO socket on the front connection strip (Maeler & Kaege VG 96 917) LOADING PLATFORM * Extendable loading platform, approx. 8,800 mm long, with rear bevel approx. 500 mm x 10° * Recess in the loading platform and bevel for accommodating excavator dipper stick approx. 3,850 x 750 x 210/290 mm (L x W x H) * TPMS tire pressure monitoring system per ECE R 141 * BPW axles and suspension, 1st axle steerable, all remaining axles hydro-mechanically forced steered * 1st axle with electromagnetic reverse lockout, activated via reverse gear and manually * Technical axle load: 12,000 kg each, air suspension with raise and lower valve * Tires: 235/75 R 17.5, twin tires, 3PMSF * Mechanical landing legs with 2-speed gearbox and crank, JOST Module B – static test load approx. 50,000 kg * Continuous 50 mm thick hardwood floor on the loading platform and interrupted between axles (increases coefficient of friction) * 1 intermediate table, approx. 300 mm wide, for the extension tube with large cross-section * Extendable (galvanized) side extensions, approx. 230 mm per side (without wooden planks) * Wheel recesses with square climbing strips, approx. 15 x 15 mm ahead of axles, open through to gooseneck cross member, approx. 700 x 410 mm (W x D) * Aluminum covers for wheel recesses, usable as bridging elements for extension OR as widening planks * Aluminum elements lockable on telescopic tubes of the extensions * Widenable U-profiles for inserting ALU covers: - on the fixed section behind the gooseneck - on the intermediate table - on the extendable platform * Wheel recesses with square climbing strips, approx. 15 x 15 mm between 1st and 2nd axle, approx. 1,480 x 700 x 410 mm (L x W x D) * Aluminum covers for the wheel recesses, usable as bridging elements for the extension OR as widening planks * Aluminum elements lockable on the extension’s telescopic tubes * 1 pair of mechanical rear supports * Remote steering from front and rear via cable remote control, with axle tracking, without installation in the tractor unit HYDRAULIC LOADING RAMPS * One pair of two-section steel ramps, Type: DR-15/60-900-4350-KG-HV-M, approx. 4,350 mm in length and approx. 900 mm wide each * Hydraulically foldable ramp tips * Ramps can be shifted hydraulically approx. 235 mm outward and approx. 215 mm inward individually * Super Grip rubber surface approx. 25 mm and steel plate surface approx. 5 mm as additional

Condition: new, maximum load weight: 39,720 kg, overall weight: 50,960 kg, axle configuration: > 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory, including immediately and short-term available vehicles, on our website. Sample equipment features. Full specification upon request. Gooseneck * With beveled front corners approx. 45° and rear bevel approx. 750 mm x 10° * 3 pairs of lashing rings (LC 5,000 daN) * Hardwood flooring, approx. 30 mm thick Loading Platform Loading platform in extendable design * 5 pairs of fold-out outer lashing rings (LC 5,000 daN) * 3 pairs of fold-out outer lashing rings (LC 10,000 daN) * 1 pair of recessed lashing rings at the front of the loading platform (LC 10,000 daN) * Recesses in the outer frame of the loading platform for securing straps (LC 2,000 daN) * Hardwood flooring approx. 48 mm thick, over axles with chequer plate covering Landing Gear * JOST (mechanical) with 2-speed gearbox, approx. 24 t lift capacity (approx. 50 t test load) Axles * BPW axles: 2 fixed axles, 2 steering axles, drum brakes * Air suspension with lift/lower function * Self-steering axle with electro-magnetic reverse lock, activated via reverse gear or manually * Tires: 205/65 R 17.5 Brake System * Wabco brake system in accordance with EU directives with EBS-E (4S3M), without interconnecting lines to the tractor unit Steel Construction * Made of high-strength fine-grained steels * Steel grades: S355J2+N/S355MC (yield strength 355MPa), S690QL/S700MC (yield strength 690MPa) Paintwork * First-class, durable corrosion protection of the standard shot-blasted welded frame, guaranteed by a 2-component (2K) zinc dust primer * High-quality 2-component (2K) top coat, single-color, RAL 3002 Carmine Red * Rear section metallized and painted in RAL 9010 (Pure White) * Rims in silver Accessories Included * 2-inch king pin * Galvanized front steel bulkhead approx. 400 mm high * Spare wheel holder in front of bulkhead * Yellow-red air couplings on galvanized connector bar front * 4 wheel chocks with holder at bulkhead * Bracket at rear of gooseneck for aluminum loading ramps * Galvanized folding supports under inclined edge of loading platform * Holder for beacon at rear of trailer * Yellow reflective tape on sides, extension, and rear in accordance with EU regulations * Brackets for warning signs with socket on both sides at the gooseneck and rear panel * TPMS tire pressure monitoring system per ECE R 141. Data transmission to the tractor unit via standardized EBS interface according to ISO 11992; for correct display, the tractor unit must support data transmission and display Iaedsu Sd U Uepfx Afhol * Plug-in aluminum side walls and tailgate on gooseneck, approx. 2,440 x 400 mm (L x H); rear galvanized stakes are removable (body length approx. 2,560 mm) * Galvanized toolbox, integrated in gooseneck slope * 6 pairs of WADER container locks in loading platform, for 1 x 20' container, 2 x 20' containers or 1 x 40' container * Sliding mounting rails for aluminum ramps at rear of vehicle * 7 pairs of stake pockets for plug-in stakes approx. 100 x 50 mm, in the outer frame of the loading platform * Galvanized cross bracket under the loading platform * Galvanized extendable widenings, extendable approx. 230 mm per side * Lift axle on front axle, controlled via TEBS E according to current axle load and load status * 5 pairs of recessed lashing rings along the central beam (LC 5,000 daN)

Condition: new, maximum load weight: 67,200 kg, overall weight: 85,000 kg, axle configuration: > 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory, including immediately and short-term available vehicles, on our website. Excerpts from the equipment. Full specifications available upon request. GOOSENECK * Gooseneck in SNT design to optimize load floor length, approx. 3,700 mm long, with rear bevel approx. 1,000 mm x 10° * For tractors: 6 x 2, 6 x 4, and short 8 x 4 * Detachable steel front wall, approx. 400 mm high * 3 kW electro-hydraulic power unit for controlling hydraulic functions, except for hydraulic winches * Outer beams of the gooseneck with mounting holes for bolt-on lashing rings Iasdpfx Aorgzv Njfhjl * 2 pairs of screw-in lashing rings included (LC 5,000 daN) * 1 pair of flat lashing rings at the rear of the gooseneck (LC 10,000 daN) * 1 pair of plug-in aluminum side boards, approx. 400 mm high, anodized * 1 plug-in aluminum rear board, approx. 400 mm high, anodized * Approx. 40 mm thick hardwood flooring above gooseneck, checker plate flooring above kingpin * 3.5 inch kingpin * Gooseneck guide plate for the fifth wheel plate, approx. 500 mm wide * Round NATO socket at the front connection strip (Maeler & Kaege VG 96 917) * In addition to the electro-hydraulic unit, a truck hydraulic connection with flow regulator, including bracket for hanging supply lines (Faymonville couplers) * 2 pairs of stake pockets recessed in the gooseneck, for plug-in stakes approx. 100 x 50 mm LOAD FLOOR * Extendable load floor, approx. 11,000 mm long, with rear bevel approx. 500 mm x 10° * Pneumatic locking with conical locking bolts and reinforced locking positions; supply lines are protected inside the extendable beams and automatically adjust to the respective deck length * BPW axles and suspension, 1st axle steered, 2nd axle fixed, all other axles hydro-mechanically forced steered * 1st axle with electro-magnetic reverse lock via reverse gear and manual activation * Axle load capacity: 12,000 kg each * Air suspension with lift and lower valve * 235/75 R 17.5 3PMSF twin tires * Mechanical landing gears with 2-speed gearbox and crank. JOST Modul B – static test load = approx. 50,000 kg * Continuous and, between axles, interrupted approx. 50 mm thick hardwood floor on load deck (increases coefficient of friction) * Slotted holes for attachable and repositionable bridging elements: – at the fixed part behind the gooseneck – on the front of the load floor * 1 sliding intermediate table, approx. 500 mm wide, for the sliding tube with large cross-section, checker plate flooring, front and rear with slotted holes for attachable and repositionable bridging elements * 1 pair of recessed flat lashing rings in the front fixed part of the load floor (LC 10,000 daN) * 9 pairs of recessed lashing rings, foldable outward, in the load floor perimeter frame (LC 10,000 daN) * 1 pair of mechanical rear supports * Remote steering from front and rear via cable remote control, with axle tracking control, no installation required in the tractor * 1st axle with automatic lift axle function and start-up assist according to EU Regulation 2021/535 * Under the gooseneck and at the rear cross member, left and right, a 7-pin socket each with holder for warning signs * Factory-applied sand coating on the perimeter frame of the load floor as well as the checker plates and the transition area between load decks