Used Müller-Mitteltal Interchangeable Chassis / Swap Chassis for sale (267)

Condition: new, maximum load weight: 8,850 kg, overall weight: 11,900 kg, axle configuration: 2 axles, loading space length: 5,000 mm, loading space width: 2,420 mm, loading space height: 500 mm, Year of construction: 2024, * KA-TA-R 11.9 "Masterline" ----Brakes: * EBS brake system * Emergency release device for spring brake cylinders * Drum brakes ----Axles: * 2 x 5.5 ton BPW axles ----Suspension: * Parabolic springs with tandem equalizer unit ----Drawbar / Flange Eye: * Drawbar height-adjustable by approx. 300 mm with 40 mm flanged towing eye ----General Attachments: * Jost mechanical support winch at front * Two mechanical, hot-dip galvanized folding support legs at rear * Plastic toolbox approx. 750 x 350 x 300 mm, mounted on the right side * Bolted underride guard * Plastic quarter fenders ----Electrics / Lighting: * 15-pin power connector * LED lighting * TPMS (Tire Pressure Monitoring System) ----Tipper Bed: * Net hooks on the sides and rear, fitted to the central locking bearings, plus 2 on the front bulkhead * Steel pallet 3-way tipper body (continuous sidewalls - without center stanchions - foldable with drop-side spring assist) * Rear stanchions bolted * Steel combination swing doors at the rear, asymmetrically split, 2-leaf, can be swung and locked to 270°, not foldable – also equipped with additional swinging frame for automatic tailgate opening during tipping. Locking via galvanized rotary bar lock and central locking system * Deactivation function for automatic tailgate during rear tipping with open swing door * 4 mm steel floor plate * Mounting rails at the rear for loading ramps ----Load Securing: * One 5 ton lashing point in each corner * Four 3 ton lashing rings recessed into the outer frame on each side ----Ramps: * One pair of aluminum loading ramps, approx. 3,310 x 400 mm (load capacity 8 tons/pair), suitable for rubber-tired & tracked vehicles * Lockable storage compartment under the load area, inset into the chassis, accessible from the rear ----Paintwork: * Drawbar, front wall, tipper bed, rear stanchions, underride guard, mechanical support legs hot-dip galvanized * Sidewalls and tailgate painted RAL 9010 pure white Bwjdsl Thymepfx Apasp * Other RAL shades for sidewalls available at extra cost * Axles, springs, towing eye, air tanks, and support winch painted black ----Other Information: * Reinforced body with load securing certificate according to EN 12642 XL * New vehicle without initial registration, with manufacturer's warranty * Subject to prior sale and errors ----Delivery Time: * Immediately available from Egestorf on the A7

Condition: new, maximum load weight: 10,800 kg, overall weight: 14,400 kg, axle configuration: 2 axles, loading space length: 6,270 mm, loading space width: 2,470 mm, Year of construction: 2026, * ETÜ-TA-R 14.4: ----Brakes: * EBS brake system * Emergency release device for spring-loaded cylinders * Drum brakes ----Axles: * 2 x 7 t Gigant axles ----Suspension: * Parabolic leaf springs with equalising unit ----Drawbar / Flange Tow Eye: Bwsdpfx Apjrwc R Ajaep * Height-adjustable drawbar, adjustable by 300 mm * Drawbar extension by 250 mm to a total length of 2,250 mm ----Electrics / Lighting: * Tyre pressure monitoring with display option in the truck via EBS signal - no installation required on the truck side * 15-pin power connector * LED lighting system 12 / 24 V * EBS multi-voltage system for towing vehicles with 12 and 24 V electrics ----General Attachments: * Support winch at the front * Rear external folding supports * Plastic toolbox approx. 858 x 500 x 500 mm mounted front right on the bulkhead exterior * Side underrun protection * Plastic quarter mudguards ----Low Loader Deck: * 50 mm softwood flooring * Preparation in front of the bulkhead for subsequent fitting of container locks * Bolted, 400 mm smooth-sheet bulkhead * Bolted rear stanchions * Side panels with spring assist ----Load Securing: * Perforated outer frame, bent approx. 45 degrees, with 2 t lashing capacity every 480 mm * Option to install 3 t folding lashing rings every 600 mm * 1 x 6.3 t lashing point each in the front and rear corners * Various drilled holes in the front and rear cross members for 1.2 t lashing options * Profifix lashing rail centrally in the longitudinal axis for lashing up to LC 3000 daN ----Ramps: * One-piece hydraulic mesh loading ramps approx. 2,750 x 600 mm (can be pushed together up to 20 mm) * Hydraulic flow divider in the trailer (for hydraulic pump output in the truck over 40 ltr./min. up to 140 ltr./min. max) ----Paintwork: * Chassis, drawbar, bulkhead, mechanical drop legs, and loading ramps hot-dip galvanised * Axles, springs, air tanks, front support winch, and flange tow eye painted in a black tone * Side panels painted in RAL 9010 pure white * Painting of side walls in any RAL colour available at extra cost ----Info: * New vehicle with manufacturer’s warranty * Errors and prior sale reserved * Sample images ----Delivery time: * Available immediately ex Egestorf

Condition: new, maximum load weight: 18,900 kg, overall weight: 24,000 kg, axle configuration: 3 axles, loading space length: 7,000 mm, loading space width: 2,480 mm, Year of construction: 2026, * TRA-Kombi 24.0: ----Brakes: * Wabco EBS-E (electronic braking system) * Emergency release device for spring brake cylinders * Drum brakes ----Suspension: * Air suspension with manual lowering at the rear ----Axles: * 3 x 11 t Gigant axles * Centre axle liftable ----Drawbar: * Pneumatically lowerable drawbar, 2,100 mm long, with 40 mm draw eye & height adjustment ----Electrics / Lighting: * LED tail lights * 15-pin electrical connector * TPMS (Tire Pressure Monitoring System) ----General Accessories: * Toolbox made from powder-coated steel (W: 1,000 mm x H: 300 mm x D: 450 mm) * Storage box for container nets made of galvanized steel (W: 960 mm x H: 300 mm x D: 450 mm) * Side underrun protection * Plastic quarter mudguards with spray protection * Plastic rear bumper pads * Mechanical drop-down supports at the rear ----Container / Low Loader Platform: * Hot-dip galvanized main frame with raised outer frame (approx. 25 mm higher) for guiding roll-off containers * Steel floor with roller recesses in the bogie area * For roll-off container transport, container length from 5,500 - 7,000 mm possible * Pneumatic 4-point clamp locking and mechanical pin-in end stops at the front of the rails * Load certification to DIN 30722 - 1 * Transport of up to 2 skip containers with a max. volume of 10 m³ each possible * Includes 8 repositionable skip stops for lateral centring of the skips, front 4 stops with pendulum stops ----Load securing: * 3 pairs of 10 t UVV lashing rings on the sides for hooking in tensioning elements for both positive and non-positive securing of the skips * 4 lashing bars in cloverleaf design (on the sides) and 1 pair of 13.4 t UVV lashing rings to the front * Load securing certificate according to DIN EN 12195-1, DIN EN 12640, DIN EN 12642 and VDI 2700 ----Ramps: * Welded seam as anti-slip surface in the ramp track area * 1 pair of aluminium loading ramps (16 t / pair) 2,800 x 400 mm suitable for rubber-tyred and chain-driven vehicles (lockable storage compartment access from rear) ----Tyres: * Tyres: 235/75 R17.5 ----Ride height: * Loaded ride height approx. 1,003 mm ----Payload: * Payload: 18,900 kg ----Paintwork: * Reflective contour marking tape on the sides & rear * Axles, turntable, drawbar, and air tank painted in black * Hot-dip galvanized main frame ----Information: * Permissible gross weight of 27,000 kg technically possible * New vehicle without first registration, with manufacturer’s warranty * Subject to errors and prior sale ----Delivery time: * Available from approx. CW 47/2026 Bodpfx Aspk D Iiepaewp

Condition: new, maximum load weight: 23,830 kg, overall weight: 30,000 kg, axle configuration: 3 axles, loading space length: 8,460 mm, loading space width: 2,520 mm, Year of construction: 2026, * T3 Profile 30.0: * EBS brake system * TPMS (Tire Pressure Monitoring System) * Emergency release device for spring brake cylinders * Drum brakes * 3 x 11 t BPW Eco axles * Parabolic springs * Mechanical rear axle compensation * Lateral underrun protection * Swivel supports at the rear of the chassis frame * Mechanically adjustable warning sign boards at front and rear * Closed plastic mudguards at the front axle and straight galvanized steel splash aprons at the rear axle, each with mud flaps * Side and rear reflective contour marking tape * Hinged cover (hot-dip galvanized) for toolbox in the turntable platform * Multi-voltage system * LED tail lights * Removable beacon at rear * Drawbar with 40 mm towing eye and height adjustment via tension spring & turnbuckle * 15-pin power connector * 4 stake pockets on each side (stakes not included) with integrated lashing points * Load securing package consisting of: 2 lashing eyes (6.4 t) at front left & right on the main frame of the turntable platform, 5 pairs of UVV folding & lowering lashing rings, loadable in all directions and recessed into the outer frame – 13.4 t in the corners, otherwise 10 t * 6 pairs of mechanical folding outriggers for a total width of 3 m (not at the rear taper) * Widening boards stored in the center of the loading area * Excavator arm rest over rear axle up to end cross member approx. 2,100 mm long (2 pairs of 6.4 t lashing rings on the side of the excavator arm rest) * Mechanical one-piece loading ramps with spring mechanism (approx. 3,000 x 720 mm) * Mechanically controlled lateral ramp adjustment * Loading area above turntable: approx. 1,960 x 2,520 mm * Unladen loading height approx. 1,070 mm * Rear loading area: approx. 6,500 x 2,520 mm * Unladen loading height approx. 910 mm (including 860 mm approach angle) Bodpfx Aox Ipa Njpaewp * Chassis, turntable, drawbar, and loading ramps hot-dip galvanized * Axles, springs, air tanks, etc. painted in black * 235/75 R 17.5 twin tires * 5,900 kg unladen weight * --Technically possible gross weight of 30,000 kg-- * Vehicle is hot-dip galvanized * New vehicle with manufacturer’s warranty * Errors and prior sale excepted * Immediately available ex Egestorf

Condition: new, maximum load weight: 6,870 kg, overall weight: 9,900 kg, axle configuration: 1 axle, Year of construction: 2026, * KWH 9.9 ML: ----Brakes: * EBS braking system * Drum brake * Emergency release device for spring accumulators ----Axle: Bwsdpfx Apju I Iqreaep * BPW axle ----Suspension: * Parabolic springs ----Drawbar / Flange coupling: * Drawbar with 40 mm threaded coupling (height-adjustable, in mm) ----Electrical System / Lighting: * 15-pin power connector * LED lighting * Flashing LED side marker lights * TPMS (Tire Pressure Monitoring System) ----General Components: * Front support jack * Spring-assisted square tube supports at the rear with base plate, safety locking pins for various support heights * Closed steel sheet fenders with splash guard * Closed side underrun protection, usable as an advertising space * Plastic toolbox with base insert (horizontal installation), approx. 500 x 350 x 400 mm ----Superstructure: * Swivelable cable drum superstructure, width between the drum arms 1,700 mm with locking mechanism to secure the drum at the ends of the support arms, as well as a locking mechanism for the cable drum superstructure with the chassis by means of a centrally arranged claw lock * Motor-hydraulic drum drive with oil motor * Valves and adjustable, rubber-coated drive rollers * Hydraulic speed controller and brake for drum drive * Steel drum shaft with 76 mm diameter, centering and rotatable ends * 1 pair of centering cones made of polyamide, stepped ----Chassis: * Chassis made of torsion-resistant square tubes and cross members ----Pump Unit: * Hydraulic pump unit with Loncin gasoline engine, including manual and electric starter * Fuel tank and manual starter * 13 HP with gear pump (150 bar) ----Tires: * 315/80 R 22.5 ----Unladen Weight: * 2,690 kg unladen weight ----Paint Finish: * Vehicle is hot-dip galvanized ----Information: * New vehicle with full manufacturer's warranty * Errors and prior sale excepted ----Delivery Time: * Available from approximately week 41/2026

Condition: new, maximum load weight: 10,500 kg, overall weight: 14,400 kg, axle configuration: 2 axles, loading space length: 7,000 mm, loading space width: 2,470 mm, loading space height: 400 mm, Year of construction: 2026, * EBS (electronic braking system) * Emergency release device for spring brake cylinders * Drum brakes * 2 x 7 t Gigant axles * Air suspension with lift and lowering system * Height-adjustable drawbar by approx. 300 mm * Drawbar extension by 250 mm to a total of 2,250 mm * Tire pressure monitoring with indication in the truck via EBS signal – no installation needed on the truck side * 15-pin power connector * LED lighting * Front landing gear * Rear external folding supports * Plastic toolbox approx. 858 x 500 x 500 mm mounted front right outside on the bulkhead * Side underrun protection * Plastic quarter mudguards * 50 mm softwood floor * Provisions for retrofitting 20" container locks at front bulkhead and rear * Bolted smooth sheet bulkhead Bedpsl Th Dfsfx Apaewp * Drop-side panels made of trapezoidal-profiled steel sheet, mid-split and foldable * Steel rear wall insertable between ramp mounts, storage in the front interior when not in use * Rear stanchions bolted * Perforated outer frame, approx. 45° angled, with 2 t lashing capacity every 480 mm * Possible installation of 3 t folding lashing brackets every 600 mm – 4 lashing rings mounted per side * One 6.3 t lashing ring in each front and rear corner * Profifix lashing rail along the longitudinal axis in the center, lashing capacity up to LC 3000 daN * Various bores in the bulkhead and rear crossmember for 1.2 t lashing capacity * One-piece mechanical grid ramps with spring system for one-man operation, approx. 2,750 x 600 mm (can be pushed together to 20 mm) * Rear drive-on slope approx. 860 mm * Chassis, drawbar, bulkhead, tailgate, folding supports and loading ramps hot-dip galvanized * Axles, springs, air tanks, flanged towing eye, and landing gear painted in black shade * Sidewall color painted to desired RAL color (no special or metallic paint) – can be changed up to approx. 6 weeks before completion * --Reinforced and certified bodywork to EN 12642 XL including load securing certificate-- * New vehicle with manufacturer’s warranty * Subject to errors and prior sale * Available from approx. calendar week 31 / 2026

Condition: new, maximum load weight: 38,290 kg, overall weight: 48,000 kg, axle configuration: 3 axles, loading space length: 8,500 mm, loading space width: 2,520 mm, Year of construction: 2026, * TS 3 Profile 30.0: ----Brakes: * Wabco EBS-E (electronic braking system) * Emergency release device for spring-loaded cylinders * Drum brakes ----Axles: * 3 x 11 ton BPW Eco Plus axles * Rear axle is self-steering with electro-pneumatic steering lock ----Suspension: * Air suspension with lift/lower mechanism and RtR valve ----Electrics / Lighting: * TPMS (Tire Pressure Monitoring System) * Smartboard control unit mounted on the trailer as an info tool with pressure sensors for total axle load display * 15-pin power connector * LED lighting system 12/24V * Removable LED beacon, mounted at rear left ----General attachments/accessories: * Side underrun protection * Landing gears at the front and mechanical swing-down supports at the rear of the chassis * Straight steel mudguards * Spare wheel holder underneath the chassis, on the right side ----Low Loader Deck: * Saddle platform with front corners chamfered at 45°, and a front-mounted toolbox made of galvanized steel (W = 2,480 x H = 500 x L = 665 mm) with hinged lid * 400 mm high, foldable and removable aluminum side boards (RAL 9010 pure white) mounted on the saddle platform * 150 mm high rear board, slotted in * Rear slope on the saddle platform leading to the lowbed, approx. 700 mm long * Saddle platform fitted with 50 mm wooden planks; lowbed platform with 60 mm wooden planks * Tread plate over the axles ----Widenings: * 8 mechanical fold-out extensions to 3 m total width (except on the rear slope; extension planks included with storage on the saddle platform) * Mechanically adjustable warning panel sets at front and rear ----Load Securing (Lashing Package): * On the saddle platform: 2 x 6.3 t lashing rings on each side, 3 x 5 t lashing rods on each side in the outer frame * On the lowbed platform (sides): 2 x 13.4 t lashing rings on each side plus 4 x 10 t lashing rings, swiveling and retractable, recessed into the outer frame * On the sides: 2 x 6.4 t lashing eyes each, plus 1 lashing ring at the rear in the excavator arm support * 2 x container locks directly after the gooseneck in the lowbed platform ----Excavator Arm Support: * Continuous excavator arm tray from the end of the last fixed axle, over the steering axle, up to the end cross member, with internal reinforcement profiles, approx. L = 2,450 x W = 770 mm x D = 270 mm ----Loading Ramps: * Mechanically operated, one-piece, hot-dip galvanized hydraulic loading ramps, approx. 3,000 x 720 mm (mechanically adjustable sideways) * 4-way valve block for future customer retrofitting of hydraulic ramp shifting * Outer plank on the ramp made of 50 mm hardwood * Climbing strips on the outer frame of the ramp and on the approach slope ----Hydraulics: Bjdpfx Aepk D I Aspaewp * Hydraulic flow divider in the trailer (for hydraulic pump capacities on truck from 40 l/min up to 120 l/min) ----Loading dimensions: * Saddle platform loading area: approx. 3,935 x 2,480 mm * Lowbed loading area: approx. 8,500 x 2,520 mm * Unladen load height approx. 910 mm (incl. 860 mm approach slope) ----Fifth wheel height: * Approx. 1,220 mm (suitable for 2- and 3-axle tractor units) ----Paint/Finish: * Chassis, loading ramps, rear support legs, and extension consoles hot-dip galvanized * Axles, landing gears, air tanks painted in a shade of black * Vehicle is hot-dip galvanized ----Info: * New vehicle with manufacturer's warranty * Subject to errors and prior sale * Sample images may show equipment features not included with the offered vehicle ----A

Condition: new, maximum load weight: 27,940 kg, overall weight: 36,000 kg, axle configuration: 3 axles, Year of construction: 2026, * Wabco EBS-E (electronic braking system) * Emergency release device for spring brake cylinders * Drum brakes * 3 x 11 t axles * Air suspension with lift and lower function as well as RtR valve * Traction assistance for shunting, activated on the first axle via EBS – without truck-side installation – with lifted lift axle + 30 mm driving height * Smart-Board infotool mounted on the trailer, equipped with pressure sensors for total axle load display * Last axle as a trailing steering axle with electro-pneumatic steering lock * Locking of the trailing axle activated from the cab for maneuvering purposes via EBS (without truck-side installation) * 2" king pin * 1 liftable axle * Side underrun protection * Front aluminum drop-down supports and rear swivel supports on the chassis * Alcoa LVL One aluminum rims * 15-pin power connector * LED lighting 12 / 24 V * Rear removable LED rotating beacon * 2 additional LED reversing lights * 2 LED work lights mounted laterally on the trailer (without truck-side installation) * 7-pin socket at the rear for oversize load lighting * Side marker lights with indicator control * Tire pressure monitoring system with display capability in the truck via EBS signal (without truck-side installation) Bwjdpfewh Hdxex Apajp * Mechanically adjustable warning sign packages front and rear * Straight steel mudguards * Semi-trailer platform with 45° chamfered front corners and a front toolbox made of galvanized, powder-coated steel sheet (W = 2,480 x H = 500 x L = 665 mm) with top hinged lid and side doors in the chamfered corners * 400 mm high aluminum side walls (RAL 9010 pure white) on the sides of the semi-trailer platform, foldable and removable * Rear panel inserted, height 150 mm * Rear slope on the semi-trailer platform to the low bed, approx. 700 mm long with anti-slip tread plate surface and a perforated strip at the end for hanging on aluminum loading ramps * Semi-trailer platform and low loader platform with 50 mm clamped timber floorboards * Checker plate above the axles * Prepared for 3 slots underneath the semi-trailer platform for storage of optional aluminum loading ramps * Swivel arm as support for connection lines from the truck to the trailer * Load securing package (LaSi): perforated outer frame on the semi-trailer platform with 45° edge and hole pattern for lashing equipment (2 t lashing capacity per point at minimum spacing of 480 mm), each side with 2 x 6.3 t recessed lashing rings in the floor, each side with 1 x 16.5 t lashing ring in the incline from the low loader platform to the semi-trailer platform, 2 pairs of 16.5 t lashing rings in the low loader platform (1 x on the longitudinal beams after the step, 1 x above the center axle beside the longitudinal beam), each side with 3 x 13.4 t lashing rings on the outer frame (1 x at start of the semi-trailer step, 1 x at start of loading ramp slope, 1 x at end of loading ramp slope), each side with 3 x 10 t lashing rings (2 x between front wheel recess and first axle, 1 x between second and third axle), each side with 3 x 5 t lashing rings bolted to the outer frame of the wheel recesses (2 x at front, 1 x at rear wheel recess) * Extended excavator arm trough running from the end of the last fixed axle over the steering axle up to the rear crossmember, with internal reinforcement profile, approx. W = 770 mm x rear D = 270/front D = 170 mm, each side with 2 x 6.4 t lashing rings in the excavator arm trough * Each side with 2 wheel recesses, 390 mm deep and 640 mm wide, f

Condition: new, maximum load weight: 17,650 kg, overall weight: 24,000 kg, axle configuration: 3 axles, loading space length: 9,230 mm, loading space width: 2,480 mm, Year of construction: 2026, * TP 30.0 with 3 cable drum supports ----Braking system: * Wabco TEBS (electronic braking system) * Emergency release device for spring brake cylinders * Drum brakes ----Axles: * 3 x 11 t Gigant axles ----Suspension: * 17.5" air suspension with lifting and lowering facility ----Drawbar: * Drawbar 1,800 mm long with 40 mm towing eye ----Electrics / Lighting: * Tyre pressure monitoring with display option in the truck dashboard via EBS signal (no truck-side installation required) * 15-pin power connector * 2 additional LED reversing lights (switched via reverse gear) * LED lighting ----General attachments: * Aluminium air tank * Stainless steel side toolbox approx. 1,000 x 300 x 600 mm * Side underrun protection * Plastic quarter mudguards * Rear underrun protection ----Platform: * Zurr-fix external frame, 45° angled, perforated for lashing devices, lashing capacity per lashing point 2,000 kg at a distance of 480 mm * Installation of 3,000 kg folding lashing rings at approx. 600 mm spacing possible - each side comes with 12 x 3,000 kg lashing rings supplied * Each side features 5 pockets for pipe stanchions 100 x 50 mm in the outer frame (pipe stanchions not included) * 30 mm phenolic resin-coated plywood floor ----Cable drum supports: * 3 galvanized cable drum supports, secured via container locks with side forklift pockets centre-to-centre 800 mm (pocket width 185 mm) * Max. drum diameter 2,600 mm and max. drum width 1,650 mm * Clear width between support arms approx. 1,775 mm, with cross-brace * Max. drum weight per support: 6,000 kg * Without drive or drum brake * Support arm with clamping lock for securing the drum shaft Bwedjx Nlkajpfx Apaep * Steel drum shaft, 76 mm diameter, with centering and rotating ends * 2 retaining collars * 2 centring cones made of polyamide * 4 x 3.2 t lashing eyes on the support arms to secure the drum against unintentional rotation and unwinding (provided by customer) ----Loading height: * approx. 1,040 mm loaded ----Paintwork/finish: * Chassis, turntable, drawbar, outer frame, and underrun protection hot-dip galvanized * Axles painted in black

Condition: new, maximum load weight: 10,500 kg, overall weight: 14,400 kg, axle configuration: 2 axles, loading space length: 6,270 mm, loading space width: 2,470 mm, loading space height: 400 mm, Year of construction: 2026, * ETÜ - TA -R 14.4 ----Braking system: * EBS braking system * Emergency release device for spring-loaded cylinders * Drum brakes ----Axles: * 2 x 7 t Gigant axles ----Suspension: * Parabolic springs with compensation unit ----Drawbar / Flange Eye: * Height-adjustable drawbar by 300 mm – drawbar extension by 250 mm to 2,250 mm * 40 mm flange towing eye ----Electrics / Lighting: * Tire pressure monitoring with display capability in the truck via EBS signal (no in-truck installation required) * 15-pin power connector * LED rear lights 12/24 V Bwjdpfxsx Ipapj Apaep * Removable LED beacon at the rear ----General Accessories: * Support winch at the front * Externally mounted hot-dip galvanized folding supports at the rear * Plastic toolbox approx. 858 x 500 x 500 mm, front right outside on the front wall * Side underrun protection * Plastic quarter mudguards ----Lowbed Area: * Provision in front of the front wall for retrofitting container locks * Bolted front wall made of smooth sheet metal * Side walls made of profiled steel sheet, foldable with side wall spring lifters * Steel rear wall insertable between the ramps – storage bracket inside at the front wall when not in use * Removable bolted rear stanchions * Inclined access ramp at rear, approx. 860 mm ----Floor Covering: * 50 mm softwood floor * 12 mm thick and 270 mm wide rubber strips on the inside of the loading ramps * 12 mm thick and 210 mm wide rubber strips on the access slope and externally on the lowbed platform (from front to rear cross member) ----Load Securing: * Perforated outer frame, approx. 45° angled, with 2 t lashing capacity every 480 mm * Installation option for 3 t folding lashing rings every 600 mm * Each front and rear corner with 1 x 6.3 t lashing ring * Multiple holes in front and rear cross member for 1.2 t lashing options ----Ramps: * One-piece mechanical grating ramps with spring mechanism for one-person operation, approx. 2,750 x 870 mm (retractable to 20 mm) ----Paintwork: * Chassis, drawbar, front wall, tailgate and ramps hot-dip galvanized * Axles, springs, air tanks and flange towing eye painted in black * Side walls painted in RAL 9010 pure white ----Information: * --Reinforced and certified body according to EN 12642 XL including load securing certificate-- * Subject to errors and prior sale * New vehicle with manufacturer's warranty ----Delivery time: Vehicle is immediately available

Condition: new, maximum load weight: 23,830 kg, overall weight: 30,000 kg, axle configuration: 3 axles, loading space length: 8,460 mm, loading space width: 2,520 mm, Year of construction: 2026, * T3 Profile 30.0: * EBS braking system * TPMS (Tire Pressure Monitoring System) * Emergency release device for spring brake cylinders Bwjdpsx Ipbgefx Apaop * Drum brakes * 3 x 11 t BPW Eco axles * Parabolic leaf springs * Mechanical axle equalization at rear * Side underrun protection * Swing supports at rear on chassis frame * Mechanically adjustable warning sign packages at front and rear * Front axle: enclosed plastic mudguards; rear axle: straight, galvanized steel fender skirts, both with splash guards * Reflective contour marking tape on the sides and rear * Hinged lid (hot-dip galvanized) for toolbox on the bogie platform * Multi-voltage system * LED tail lights * Removable beacon at the rear * Drawbar with 40 mm towing eye and height adjustment via tension spring & turnbuckle * 15-pin electrical socket * Four stake pockets each side (no stakes present), with simultaneous lashing capability * Load securing package including: 2 lashing eyes (6.4 t) front left & right on the main frame of the bogie platform; 5 pairs of UVV lashing rings, swiveling and lowerable, loadable in all directions and recessed in the outer frame - 13.4 t in the corners, otherwise 10 t * 6 pairs of mechanical folding outrigger extensions for 3-meter overall width (not at rear slope) * Extension planks stored in the middle of the loading platform * Excavator boom trough above rear axle up to end cross member, approx. 2,100 mm long (2 pairs of 6.4 t lashing rings at sides of the trough) * Hydraulic one-piece loading ramps (approx. 3,000 x 720 mm) * Hydraulic lateral ramp shift * Deck over turntable: approx. 1,960 x 2,520 mm * Unladen loading height: approx. 1,070 mm * Rear deck: approx. 6,500 x 2,520 mm * Unladen loading height: approx. 910 mm (incl. 860 mm ramp slope) * Chassis, bogie, drawbar, and loading ramps hot-dip galvanized * Axles, springs, air tanks etc. painted in a black tone * 235/75 R 17.5 twin tires * 5,900 kg unladen weight * --Permissible total weight of 30,000 kg technically possible-- * Vehicle is hot-dip galvanized * New vehicle with manufacturer warranty * Subject to errors and prior sale * Available from approx. calendar week 36/2026

Condition: new, maximum load weight: 37,560 kg, overall weight: 48,000 kg, axle configuration: 3 axles, Year of construction: 2026, * TS 3 RM ML 30.0: ----Brakes: * Wabco EBS-E (electronic braking system) * Emergency release device for spring brake cylinders * Drum brakes ----Axles: * 3 x 11 t BPW axles * Start assist for maneuvering purposes on the first axle, activated via EBS (no truck-side installation required) * Last axle is a trailing steering axle with electro-pneumatic steering lock * Lock for the trailing axle, actuated from the driver's cab for maneuvering purposes via EBS (no truck-side installation required) ----Suspension: * Air suspension with raise/lower system and RtR valve ----Electrical / Lighting: Bsdoykx Nqepfx Apaowp * Smart-Board installed as an information tool on the trailer, with pressure sensors for total axle load display * 15-pin power connector * LED lighting 12/24 V * Removable rear LED beacon * 2 additional LED reverse lights * 7-pin socket at rear for overlength lighting * Side marker lights with indicator actuation * Tire pressure monitoring with display option in the truck via EBS signal (no truck-side installation required) ----General Attachments: * Side underrun protection * Landing gears at the front and swing-out supports at the rear * Straight steel fenders * Spare wheel carrier in front of the bulkhead crossmember (without spare wheel) * Mechanically adjustable warning panel sets at front and rear * Pivoting arm as a carrier for connection lines from the truck to the trailer ----Low Loader Bed: * Second kingpin position * Fifth-wheel platform with 45° chamfered front corners and front toolbox made of galvanized, powder-coated steel plate (W = 2,480 mm x H = 500 mm x L = 665 mm) with hinged lid * 400 mm high aluminum sideboards (RAL color of choice), foldable and removable on the fifth-wheel platform * 150 mm high plug-in rear wall * Rear slope on the fifth-wheel platform towards the low-bed, approx. 700 mm long with tread plate covering and a perforated bar at the end for hooking on aluminum ramps * Fifth-wheel platform with 50 mm clamped timber planks, and low-loader deck with 60 mm clamped timber planks * Tear plate over the axles * 9 mechanical swing-out extensions for total width of 3 m (not on rear slope), extension boards available with a transverse storage compartment under the loading area * Prepared for 3 insertion shafts under the fifth-wheel platform for storing either aluminum ramps or timber planks for wheel recess covers * Preparation for container locks on the swan neck ----Load Securing (LaSi Package): Fifth-wheel Platform: * Perforated outer frame, bent at 45°, with hole pattern for lashing equipment (2 t lashing force per lashing point at a minimum spacing of 480 mm) * On each side, 3 x 13.4 t recessed lashing rings in the floor (1 on the fifth-wheel platform, 1 on the longitudinal member after the neck step, 1 above the middle axle next to the longitudinal member) Low Loader Platform: * On each side, 3 x 13.4 t lashing rings on the outer frame (1 at the neck step of the fifth-wheel platform, 1 at the start of the ramp, 1 at the end of the ramp) * On each side, 2 x 10 t lashing rings (1 between the front wheel recess and the first axle, 1 between the 2nd and 3rd axle) * On each side, 3 x 5 t lashing rings bolted to the outer frame of the wheel recesses (2 at the front, 1 at the rear wheel recess) ----Excavator Arm Rest: * Extended excavator arm rest from the end of the last fixed axle over the steering axle up to the rear crossmember, continuous with internal reinforcement profile, approx. 770 mm wide x T at t

Condition: new, maximum load weight: 23,830 kg, overall weight: 30,000 kg, axle configuration: 3 axles, loading space length: 8,460 mm, loading space width: 2,520 mm, Year of construction: 2026, * T3 Profile 30.0: * EBS braking system * TPMS (Tire Pressure Monitoring System) * Emergency release device for spring brake cylinders * Drum brakes * 3 x 11 t BPW Eco axles * Parabolic leaf springs * Mechanical axle equalization at rear * Side underrun protection * Swing supports at rear on chassis frame * Mechanically adjustable warning sign packages at front and rear * Front axle: enclosed plastic mudguards; rear axle: straight, galvanized steel fender skirts, both with splash guards * Reflective contour marking tape on the sides and rear * Hinged lid (hot-dip galvanized) for toolbox on the bogie platform * Multi-voltage system * LED tail lights * Removable beacon at the rear * Drawbar with 40 mm towing eye and height adjustment via tension spring & turnbuckle * 15-pin electrical socket * Four stake pockets each side (no stakes present), with simultaneous lashing capability * Load securing package including: 2 lashing eyes (6.4 t) front left & right on the main frame of the bogie platform; 5 pairs of UVV lashing rings, swiveling and lowerable, loadable in all directions and recessed in the outer frame - 13.4 t in the corners, otherwise 10 t * 6 pairs of mechanical folding outrigger extensions for 3-meter overall width (not at rear slope) * Extension planks stored in the middle of the loading platform * Excavator boom trough above rear axle up to end cross member, approx. 2,100 mm long (2 pairs of 6.4 t lashing rings at sides of the trough) * Hydraulic one-piece loading ramps (approx. 3,000 x 720 mm) * Hydraulic lateral ramp shift * Deck over turntable: approx. 1,960 x 2,520 mm * Unladen loading height: approx. 1,070 mm * Rear deck: approx. 6,500 x 2,520 mm * Unladen loading height: approx. 910 mm (incl. 860 mm ramp slope) * Chassis, bogie, drawbar, and loading ramps hot-dip galvanized * Axles, springs, air tanks etc. painted in a black tone * 235/75 R 17.5 twin tires * 5,900 kg unladen weight * --Permissible total weight of 30,000 kg technically possible-- * Vehicle is hot-dip galvanized * New vehicle with manufacturer warranty * Subject to errors and prior sale Bjdpfx Ajx Ipb Hopajwp * Available from approx. calendar week 36/2026

Condition: new, maximum load weight: 9,070 kg, overall weight: 11,900 kg, axle configuration: 2 axles, loading space length: 5,500 mm, loading space width: 2,010 mm, loading space height: 325 mm, Year of construction: 2026, * ETS-TA-B 11.9: * Wabco EBS (electronic braking system) * TPMS (tire pressure monitoring system) * Drum brakes, 2 x 5.5 t Gigant axles * Parabolic springs with compensating unit * Drawbar height adjustable by approx. 300 mm * BPW landing gear * Mechanical drop-down supports at the rear * Plastic toolbox at the front right on the bulkhead * Side underrun protection * LED lighting * 50 mm softwood floor * In the corners in front of the bulkhead and the rear crossmember, each 1 x 6.3 t lashing ring, as well as 2 x 6.3 t UVV lashing rings each side, recessed into the outer frame * One-piece mechanical grating loading ramps with spring mechanism for single-person operation approx. 2,350 x 870 mm (inner spacing 20 mm, ramps are not movable) * Bulkhead, side walls, mudguards and drawbar hot-dip galvanized Bwedpjwyhzpofx Apajp * Axles, springs, air reservoir, and front landing gear painted in black * New vehicle with full manufacturer's warranty * Errors and prior sale reserved * Available from approx. calendar week 35 / 2026

Condition: new, maximum load weight: 6,810 kg, overall weight: 9,600 kg, axle configuration: 1 axle, loading space length: 4,030 mm, loading space width: 2,420 mm, loading space height: 700 mm, Year of construction: 2026, * EK 9.6 ----Brakes: * EBS (Electronic Braking System) * Emergency release device for spring brake cylinders * Drum brakes ----Axle: * SAF axle ----Suspension: * Parabolic springs ----Drawbar / Flange Drawbar Eye: * Drawbar as central pole with 40 mm bolted drawbar eye * Stepless drawbar height adjustment with spindle lifting mechanism instead of rigid drawbar ----Coupling height: * Standard coupling height approx. 900 mm (+/- 150 mm) ----Electrics / Lighting: * Tire pressure monitoring with display capability in the truck via EBS signal (no installation required on the truck side) * 15-pin power plug * LED tail lights * Flashing side marker lights ----General Attachments: * Support winch at the front * Enclosed plastic mudguards * Folding underrun guard for pavers ----Chassis: * Chassis made of fine-grained steel ----Tipping body: * 3-way tipping body for pallets * 700 mm steel front wall * Aluminum side walls, asymmetrical – continuous, without center stanchion – foldable with long-stroke locks and pendulum action via manual central locking * Steel rear wall 800 mm high with automatic rear wall opening during rear tipping * 4 mm Hardox 450 steel floor ----Load securing: * 2 pairs of 3-ton lashing rings recessed and foldable in the steel floor on each side ----Paintwork: Bwsdsw Ndr Uepfx Apaep * Chassis, drawbar, underrun guard hot-dip galvanized * Tipping body painted in a RAL color of your choice (no special or metallic paints); can be changed up to approx. 6 weeks before completion ----Information: * New vehicle with manufacturer’s warranty * Errors and prior sale excepted ----Delivery time: * Available from approx. week 42/2026

Condition: new, maximum load weight: 20,500 kg, overall weight: 27,000 kg, axle configuration: 3 axles, loading space length: 7,000 mm, loading space width: 2,470 mm, Year of construction: 2026, * ETÜ-TR 27.0 Platform: * EBS (electronic braking system) * Emergency release device for spring-loaded brake cylinders * Drum brakes * 3 x 9 t BPW Eco axles * Air suspension with lift and lower function including RTR feature * 1st axle liftable * Last axle as trailing steering axle with electro-pneumatic steering lock activated via reverse gear PIN (lockout of the trailing axle from driver's cab for maneuvering - no truck-side installation required - assigned to PIN 10 of the 15-pin connector; for maneuvering purposes only, not for public road use) * SmartBoard control box as infotool with pressure sensors for total axle load display * Tire pressure monitoring with display option in the truck via EBS signal (no truck-side installation required) * Fixed center drawbar with 50 mm flanged towing eye (900 mm when loaded, height adjustable at the head plate) * Mechanical support winch in front, mechanical swing-down supports at the rear of chassis * Mechanically adjustable warning sign package front and rear * Toolbox made of galvanized steel sheet - black powder coated - approx. 650 x 300 x 600 mm, mounted on the right side * Hydraulic flow divider * Continuous sidewalls (without center stanchion) up to the approach ramp * Folding rear stanchions * Steel rear wall inserted in front of rear stanchions * 15-pin power connector * LED taillights * LED revolving beacon (removable), incl. bracket and installation * 2 x LED reversing lights at the rear of vehicle (activated by reverse gear) * Flashing LED side marker lights * 60 mm larch/douglas fir flooring * 400 mm plug-in steel front wall * Perforated outer frame, approx. 45° chamfered with provisions for mounting 3 t folding lashing brackets Bodpfx Aper Dpz Aeajwp * 1 x 10 t lashing ring in each corner; additionally, 2 x 10 t and 3 x 6.3 t lashing rings on each side * Various holes in front and rear cross-members for 1.2 t lashing options * Hydraulic one-piece loading ramps approx. 3,000 x 720 mm, mechanically adjustable sideways * 4-way hydraulic control block for optional retrofitting of hydraulic ramp displacement * Chassis, drawbar, front wall, mechanical rear supports, loading ramps, and tailgate fully hot-dip galvanized * Axles, air tanks, flanged towing eye, and front support winch painted in black * Hydraulic flow divider in trailer (for hydraulic pump capacity in truck from over 40 l/min up to 120 l/min) * New vehicle with manufacturer’s warranty * Errors and interim sales excepted * Immediately available ex Egestorf

Condition: new, maximum load weight: 10,500 kg, overall weight: 14,400 kg, axle configuration: 2 axles, loading space length: 7,000 mm, loading space width: 2,470 mm, loading space height: 400 mm, Year of construction: 2026, * EBS (electronic braking system) * Emergency release device for spring brake cylinders * Drum brakes * 2 x 7-ton Gigant axles * Air suspension with lifting and lowering system Bjdpjl Thvxjfx Apaswp * Drawbar height adjustable by approx. 300 mm * Drawbar extension by 250 mm, total length 2,250 mm * Tire pressure monitoring with display option in the truck via EBS signal - no installation required on the truck side * 15-pin power connector * LED lighting * Support winch at the front * External folding support legs at the rear * Plastic toolbox approx. 858 x 500 x 500 mm, mounted front right on the bulkhead * Lateral underrun protection * Plastic quarter mudguards * 50 mm softwood flooring * Mountings for subsequent installation of 20" container locks in front of the bulkhead and at the rear * Bolted bulkhead made of smooth sheet metal * Fold-down side walls made of trapezoidal-profiled steel sheet, centered, 1x split * Steel rear wall, slide-in between ramp brackets, storage for when not in use inside front of bulkhead * Bolted rear stanchions * Perforated outer frame, approx. 45° angled, with 2 t lashing capacity every 480 mm * Option to install 3 t fall-arrest lashing brackets every 600 mm - 4 lashing rings per side installed * In each corner at the front and rear: 1 x 6.3 t lashing ring * Profifix lashing rail along the longitudinal axis in the center, suitable for lashing up to LC 3000 daN * Various holes in front and rear cross members for 1.2 t lashing option * One-piece mechanical grid ramps with spring mechanism for one-person operation, approx. 2,750 x 600 mm (can be collapsed to 20 mm) * Rear approach angle approx. 860 mm * Chassis, drawbar, bulkhead, tailgate, folding supports, and ramps hot-dip galvanized * Axles, springs, air tanks, flange towing eye, and support winch painted in black tone * Side walls painted in RAL color of choice (special or metallic paints not available), can be changed up to approx. 6 weeks prior to completion * -- reinforced and certified structure according to EN 12642 XL including load securing certificate -- * New vehicle with manufacturer's warranty * Subject to errors and prior sale * Available from approx. calendar week 31 / 2026

Condition: new, maximum load weight: 23,830 kg, overall weight: 30,000 kg, axle configuration: 3 axles, loading space length: 8,460 mm, loading space width: 2,520 mm, Year of construction: 2026, * T3 Profile 30.0: Bodpjx Ipavofx Apajwp * EBS braking system * TPMS (Tire Pressure Monitoring System) * Emergency release mechanism for spring brake cylinders * Drum brakes * 3 x 11 t BPW Eco axles * Parabolic leaf springs * Mechanical axle equalizer at rear * Side underrun protection * Swivel support legs at the rear on the chassis frame * Mechanically adjustable warning sign packages front and rear * Front axle with closed plastic mudguards, rear axle with straight galvanized steel fender skirts, each with splash guards * Reflective contour tape on the sides and rear * Hinged cover (hot-dip galvanized) for the toolbox in the turntable platform * Multi-voltage system * LED tail lights * Removable rotating beacon at the rear * Towing bar with 40 mm towing eye and height adjustment via tension spring & turnbuckle * 15-pin electrical connector * 4 stake pockets per side (stakes not included), can be used for load securing * Load-securing package consists of: 2 lashing eyes (6.4 t) front left & right on the main frame of the turntable platform, 5 pairs of UVV swivel and retractable lashing rings, loadable in all directions, recessed into the outer frame – 13.4 t in the corners, otherwise 10 t * 6 pairs of mechanical folding extensions for a total width of 3 meters (not in the rear taper) * Widening boards stored in the center of the loading area * Excavator arm rest over rear axle up to end member, approx. 2,100 mm long (2 pairs of 6.4 t lashing rings to the side in the excavator arm rest) * Mechanical one-piece loading ramps with spring mechanism (approx. 3,000 x 720 mm) * Mechanical lateral ramp adjustment * Loading area above turntable: approx. 1,960 x 2,520 mm * Load height unladen approx. 1,070 mm * Rear loading area: approx. 6,500 x 2,520 mm * Load height unladen approx. 910 mm (incl. 860 mm approach angle) * Chassis, turntable, towing bar, and ramps hot-dip galvanized * Axles, springs, air tanks, etc. painted in a shade of black * 235/75 R 17.5 twin tires * Unladen weight: 5,900 kg * --Technical gross weight up to 30,000 kg possible-- * Vehicle is hot-dip galvanized * Brand new vehicle with manufacturer warranty * Errors and prior sale excepted * Immediately available from Egestorf

Condition: new, maximum load weight: 29,850 kg, overall weight: 38,000 kg, axle configuration: 2 axles, loading space length: 8,000 mm, loading space width: 2,520 mm, Year of construction: 2026, TS 2 ML ----Brakes: * EBS-E (electronic braking system) * Emergency release device for spring brake cylinders * Drum brakes ----Axles: * 2 x 10 t axles * Last axle as a trailing steering axle with electro-pneumatic steering lock activated by PIN in reverse gear * Additional lock for the trailing axle, operable from the driver's cab for maneuvering purposes – without truck-side installation – assigned to PIN 10; the lock must be disengaged before driving on public roads ----Suspension: * Air suspension with lift and lower function and RtR (Ride to Reduce) function ----Electrics / Lighting: * Tire pressure monitoring system with display capability in the truck's display via EBS signal – without truck-side installation * LED tail lights 12 / 24 V * Flashing side marker lights * LED reverse lights activated by reverse gear * SmartBoard installed as info tool with pressure sensors solely for total axle load display * 7-pin socket at the rear for illumination of overlength loads * LED beacon (removable) at the rear ----General Attachments: * Aluminum air tanks * Manual crank landing gears * Galvanized steel mudguards * Swivel arm as carrier for connection lines in front of the front bulkhead ----Warning Package: * Mechanically adjustable warning sign package ----Lowbed Platform: * 50 mm thick flooring made from larch / Douglas fir instead of spruce / fir * Rear slope – 700 mm long – on the semi-trailer deck to the low bed with checker plate covering and at the end a perforated strip for attaching aluminum drive-on ramps * Tread plate cover over the wheels * SP combo package: toolbox with 45° corners made of galvanized sheet steel, additionally powder-coated in RAL 9006 white aluminum color, mounted on the semi-trailer platform approx. 2,480 x 500 mm * Hinged lid on top and side doors in the angled corners * Fold-down aluminum side boards, 500 mm high on the trailer platform, incl. foldable and removable rear stanchions * Plug-in aluminum rear wall, 150 mm high * 2nd kingpin position * Preparation for container locks * Preparation for 3 receiving pockets in the transition slope from lowbed to gooseneck * Preparation for retrofitting folding outriggers to achieve 3-meter width, including welded-in mounting brackets in the outer frame ----Load Securing: Semi-trailer platform: * 50 mm holes in the front corners and front for 1.2 t lashing force per hole * 2 x 16.5 t lashing rings recessed in the floor at the side near the approach slope * Perforated, 45°-bent outer frame with hole pattern for lashing equipment (2 t lashing points every 480 mm) * Each side with 2 x 6.3 t retractable lashing rings recessed in the outer frame Low-bed platform: * 2 x 16.5 t lashing rings recessed centrally just in front of the approach slope to the gooseneck * Each side with 3 pairs of 13.5 t and 5 pairs of 10 t retractable lashing rings recessed into the outer frame * Each side with 4 stake pockets recessed into the outer frame * Profifix lashing rail in the center longitudinal axis (lashing capacity 3 t per lashing circuit) ----Excavator Arm Rest: * From end of last rigid axle to end cross member B = 770 mm, D = 270 mm (each side with 2 x 6.4 t lashing rings welded in place in the excavator arm rest) ----Ramp: * Hydraulic one-piece "ALLTEC" aluminum drive-on ramps, approx. 3,200 x 750 mm * Load capacity 13 t per ramp (26 t/pair) * Hydraulic ramp shifting on sliding tube of the ramp shaft Bwsdpeykx I Hsfx Apaop ----Hydraulics: * Hydraulic flow divider in the trail

Condition: new, maximum load weight: 29,850 kg, overall weight: 38,000 kg, axle configuration: 2 axles, loading space length: 8,000 mm, loading space width: 2,520 mm, Year of construction: 2026, TS 2 ML ----Brakes: * EBS-E (electronic braking system) * Emergency release device for spring brake cylinders * Drum brakes ----Axles: * 2 x 10 t axles * Rear axle as a trailing steering axle with electro-pneumatic steering lock activated by PIN when reverse gear is selected * Additional lock for the trailing axle, operated from the driver's cab for maneuvering purposes – no truck-side installation required – assigned to PIN 10. The lock must be deactivated before driving on public roads ----Suspension: * Air suspension with lifting and lowering function as well as RtR (Ride to Recover) function ----Electrics / Lighting: * Tire pressure monitoring system with display option in the truck dashboard via EBS signal – no truck-side installation required * LED tail lights 12 / 24 V * Flashing side marker lights * LED reversing lights switched via reverse gear * SmartBoard installed as info tool with pressure sensors exclusively for total axle load display * 7-pin socket at the rear for overlength lighting * Removable LED rotating beacon at the rear ----General attachments: * Aluminum air tanks * Mechanical crank landing legs * Galvanized steel mudguards * Swivel arm as a carrier for connection lines mounted in front of the front panel ----Warning package: * Mechanically adjustable warning sign package ----Low-bed platform: * 50 mm flooring made of larch / Douglas fir instead of spruce / fir * Rear slope – 700 mm long – on the gooseneck deck to the low-bed with checker plate covering, and perforated strip at the end for attaching aluminum approach ramps * Tread plate cover over wheels * SP-Combo package: toolbox with 45° corners, made of galvanized sheet steel, additionally powder-coated in RAL 9006 white aluminum, mounted on the platform approx. 2,480 x 500 mm * Flip-top lid as well as side doors in the slanted corners * Folding aluminum side walls 500 mm high on the platform, incl. folding and removable rear stanchions * Plug-in aluminum rear wall 150 mm high Bsdeykx I Topfx Apajwp * Second kingpin position * Preparation for container lock * Preparation for 3 insert pockets in the inclined ramp from low-bed to gooseneck * Preparation for retrofitting folding outriggers for 3 m widening by welding the mounting brackets into the outer frame ----Load securing: Fifth wheel platform: * In the front corners and at the front, 50 mm holes for 1.2 t lashing force per hole * 2 x 16.5 t lashing rings recessed in the floor on the side at the approach slope * Perforated and bent 45° outer frame with hole pattern for lashing equipment (2 t lashing points every 480 mm) * On each side: 2 x 6.3 t retractable lashing rings recessed into the outer frame Low-bed platform: * 2 x 16.5 t lashing rings recessed centrally directly in front of the approach slope to the gooseneck * On each side: 3 pairs of 13.5 t and 5 pairs of 10 t retractable lashing rings recessed into the outer frame * On each side: 4 stanchion pockets recessed into the outer frame * Profifix lashing rail centered in the longitudinal axis (lashing point 3 t per securing circle) ----Excavator arm trough: * From the end of the last rigid axle to the end cross member B = 770 mm, D = 270 mm (on each side 2 x 6.4 t lashing rings for the excavator arm trough, permanently welded) ----Ramp: * Hydraulic one-piece "ALLTEC" aluminum approach ramps approx. 3,200 x 750 mm * Load capacity 13 t per ramp (26 t per pair) * Hydraulic ramp shifting on sliding pipe of the ramp shaft ----Hydraulics: * Hydraulic flow

Condition: new, maximum load weight: 10,500 kg, overall weight: 14,400 kg, axle configuration: 2 axles, loading space length: 6,270 mm, loading space width: 2,470 mm, loading space height: 400 mm, Year of construction: 2026, * ETÜ - TA -R 14.4 ----Brakes: * EBS braking system * Emergency release device for spring-loaded cylinders * Drum brakes ----Axles: * 2 x 7 t Gigant axles ----Suspension: * Parabolic springs with compensating aggregate Bjdjx Ipbaopfx Apaewp ----Drawbar / Flange Eye: * Height-adjustable drawbar by 300 mm - drawbar extension by 250 mm to 2,250 mm total length * 40 mm flange towing eye ----Electrics / Lighting: * Tire pressure monitoring with in-cab display option via EBS signal (no installation on truck required) * 15-pin electrical connector * LED tail lights 12 / 24 V * Rear LED beacon (removable) ----General Attachments: * Support crank at the front * Externally mounted, hot-dip galvanized folding supports at rear * Plastic toolbox approx. 858 x 500 x 500 mm, mounted front right on bulkhead * Lateral underrun protection * Plastic quarter mudguards ----Low Bed Deck: * Fixture in front of bulkhead for retrofitting container locks * Bolted smooth-sheet bulkhead * Drop sides made of steel sheet, trapezoidal profile, foldable with drop side spring lifter * Steel tailgate, stowable between ramps - bracket for non-use inside, in front of bulkhead * Bolted rear stanchions * Rear incline approx. 860 mm ----Floor Covering: * 50 mm softwood floor * 12 mm thick, 270 mm wide rubber strip on inner side of loading ramps * 12 mm thick, 210 mm wide rubber strips in the rear incline and outer area of low bed platform (from bulkhead to rear cross member) ----Load Securing: * Slotted external frame, approx. 45° bent, with 2 t lashing capacity every 480 mm * Option to install 3 t folding lashing rings every 600 mm * In the front and rear corners, 1 x 6.3 t lashing ring each * Various holes in the bulkhead and rear cross member for 1.2 t lashing options ----Ramps: * One-piece mechanical mesh loading ramps with spring mechanism for single-person operation, approx. 2,750 x 870 mm (adjustable down to 20 mm spacing) ----Paintwork: * Chassis, drawbar, bulkhead, tailgate, and loading ramps hot-dip galvanized * Axles, springs, air tanks, and flange towing eye painted in black * Sideboards painted RAL 9010 pure white ----Additional Information: * --Reinforced and certified bodywork to EN 12642 XL, including load securing certificate-- * Errors and prior sale excepted * New vehicle with manufacturer's warranty ----Lead Time: Vehicle available immediately ex Egestorf

Condition: new, maximum load weight: 17,650 kg, overall weight: 24,000 kg, axle configuration: 3 axles, loading space length: 9,230 mm, loading space width: 2,480 mm, Year of construction: 2026, * TP 30.0 with 3 cable drum supports ----Braking System: * Wabco TEBS (electronic braking system) * Emergency release device for spring-loaded cylinders * Drum brakes ----Axle: * 3 x 11 t Gigant axles ----Suspension: * 17.5" air suspension with lifting and lowering system ----Drawbar: * Drawbar 1,800 mm long with 40 mm towing eye ----Electrics / Lighting: * Tire pressure monitoring with display option in the truck display via EBS signal (no installation required on truck side) * 15-pin power plug * 2 additional LED reversing lights (switched via reverse gear) * LED lighting ----General Attachments: * Aluminum air tank * Stainless steel toolbox on the side approx. 1,000 x 300 x 600 mm * Side underride protection * Plastic quarter mudguards Bwodpjx Nlkgjfx Apasp * Underrun protection ----Platform: * Zurr-fix external frame, bend 45°, with perforation for lashing equipment, lashing force per point 2,000 kg at 480 mm intervals * Option to install 3,000 kg drop lashing brackets at approx. 600 mm intervals – includes 12 pcs. 3,000 kg lashing brackets per side * Each side with 5 pockets for pipe stanchions 100 x 50 mm in the outer frame (stanchions not included) * 30 mm phenolic plywood floor ----Drum Supports: * 3 galvanized drum supports, secured with container locks and side forklift pockets, center-to-center 800 mm (pocket width 185 mm) * Max. drum diameter 2,600 mm, max. drum width 1,650 mm * Clear width between the support arms approx. 1,775 mm, with crossbar * Drum weight per support: 6,000 kg * Without drive and drum brake * Support arm with tension lock for drum shaft securing * Steel drum shaft, 76 mm diameter, with centering and rotating ends * 2 set collars * 2 centering cones made of polyamide * 4 pcs. 3.2 t lashing eyes on the support arms for customer-side securing of the drum against rotation and unspooling ----Loading height: * Approx. 1,040 mm loaded ----Painting: * Chassis, turntable, drawbar, external frame, underrun protection hot-dip galvanized * Axles painted black ----Information: * Technical GVWR upgrade to 30 t possible * New vehicle with manufacturer’s warranty * Errors and prior sale excepted ----Delivery time: * Available from approx. week 51 / 2026

Condition: new, maximum load weight: 13,410 kg, overall weight: 18,000 kg, axle configuration: 2 axles, loading space length: 4,995 mm, loading space width: 2,380 mm, loading space height: 900 mm, loading space volume: 11 m³, Year of construction: 2026, * KA-TA-R 18.0 ML * Wabco EBS-E (electronic braking system with RSS) * Emergency release system for spring brake cylinders * Drum brakes * Tire pressure monitoring system with display option in the truck dashboard via EBS signal – no truck-side installation required * 2 x 9 t Gigant axles * Air suspension with level control during tipping operations * Drawbar with 50 mm flange towing eye (adjustable +77 mm and -33 mm via offset plate) * Jost landing gear at the front * Folding galvanized steel underrun protection for paver feeding * Closed individual plastic mudguards * Standing platform on the front wall * Manual sliding tarpaulin * 15-pin electrical connector * LED tail lights with galvanized protective hood * 2 LED reversing lights Bwjdpfx Apjxl Nkgjasp * Chassis made of high-tensile steel * Steel 3-side tipper body (side walls with MM profile – seamless without central stanchion – pendulum-mounted via manual central locking, and left side folding down with drop side spring assist) * Sliding tarpaulin similar to RAL 7038 agate grey with tarpaulin tensioning using side ratchet tensioners and front/rear elastic cords * Front wall platform made of grating with step at drawbar and handhold at front wall * Rear wall – made of HBW 400 steel – pendulum-mounted with automatic 2-claw lock * 5 mm steel floor made of HBW 450 steel * 4 x 3 t recessed and foldable lashing rings per side, embedded in steel floor * Reinforced and certified body according to EN 12642 XL, including load securing certificate up to 19 t * Side wall painting in any desired RAL color (excluding special or metallic finishes), changeable up to approx. 6 weeks before completion * Axles, air reservoirs, landing gear, and flange towing eye painted in a shade of black * Chassis, underrun protection, and drawbar hot-dip galvanized * New vehicle with full manufacturer's warranty * Subject to errors and prior sale * Available approx. from week 44 / 2026

Condition: new, maximum load weight: 13,490 kg, overall weight: 18,000 kg, axle configuration: 2 axles, loading space length: 7,000 mm, loading space width: 2,480 mm, Year of construction: 2025, TRA-Kombi 18.0: * 3 in 1 = for roll-off containers, skip containers, and as a low-loader ----Braking system: * EBS-E (Electronic Braking System) * Emergency release device for spring-loaded cylinders * Drum brakes ----Axles: * 2 x 10.5 ton axles ----Suspension: * Air suspension with manual rear lowering ----Drawbar: * Pneumatically lowerable drawbar, 2,100 mm long with 40 mm towing eye and height adjustment device ----Electrics / Lighting: * TPMS (Tyre Pressure Monitoring System), displayable in the truck via EBS signal (no installation required on the truck side) * LED tail lights 12 / 24 V * 15-pin power connector ----General attachments: * Tool box made of powder-coated sheet steel * Spare wheel holder in basket design, right side * Closed side underrun protection * Plastic quarter mudguards with spray protection * Plastic rear impact protection buffers * Foldable A-sign at rear ----Loading platform: * Hot-dip galvanized main frame with raised outer frame for guiding roll containers * Steel plate floor with roller recesses in the bogie area * Suitable for roll-off containers with length from 5,500 to 7,000 mm * Pneumatic 4-point clamp locking system and mechanically insertable stop angles at the front in the track * For transport of up to 2 skip containers with max. 10 m³ volume * Includes 8 plug-in skip stops for lateral centering of the skips, front 4 skip stops plug-in with swiveling stop * Weld bead as anti-slip coating in the ramp track area * Mechanical drop-down support legs at the rear ----Load securing: * 3 pairs of 10 t UVV lashing rings on the sides for attaching tensioning elements for positive and non-positive securing of skips; 4 clover-leaf lashing bars on each side * 1 pair of 13.4 t UVV lashing rings to the front * 4 x 8 t lashing eyes on each side, recessed into the outer frame ----Ramps: * Aluminum approach ramps (10.6 t / pair), 2,800 x 470 mm; suitable for rubber-tired and tracked vehicles (lockable storage compartment at rear) ----Paintwork: * Reflective contour tape on sides and rear * Frame hot-dip galvanized * Axles, drawbar painted black ----Information: * Load securing certificate according to DIN 30722-1 * Load securing certificate according to DIN EN 12195-1, DIN EN 12640, DIN EN 12642, and VDI 2700 * --Permissible gross weight of 20,000 kg technically possible-- * New vehicle without initial registration with manufacturer warranty Bwodpowb Rakjfx Apasp * Errors and prior sale excepted ----Delivery time: * Available immediately ex Egstorf

Condition: new, maximum load weight: 30,440 kg, overall weight: 40,000 kg, axle configuration: > 3 axles, Year of construction: 2026, Equipment: ABS, T 4 Profi 40.0 ----Brakes: * Wabco EBS-E (electronic braking system) * Emergency release device for spring brake cylinders * Drum brakes ----Axles: * 4 x 11 t Gigant axles ----Suspension: * Air suspension with lift/lower function and RtR valve ----Drawbar: * Straight drawbar with 50 mm towing eye and infinitely adjustable height setting ----Electrical / Lighting: * Tire pressure monitoring system with display option in the truck dashboard via EBS signal (no truck-side installation required) * SmartBoard as an infotool with pressure sensors for axle load indication by axle group * 15-pin power connector * LED tail lights * Removable LED beacon at the rear ----General Attachments: * Warning sign packages front & rear * 2 x toolboxes made of galvanized and powder-coated steel approx. 650 x 300 x 600 mm, mounted on the right side * Front closed plastic single mudguards * Rear straight steel splash guards each with spray suppression * Side underrun protection ----Low-loader Platform: * Rotary-platform extension by 520 mm with 45° corners and 3 integrated storage compartments incl. lockable covers * Flooring over rotary-platform from 50 mm and on low-loader platform from 60 mm softwood * 20 mm rubber flooring instead of timber in the deck area, low-loader length 6,780 mm including access ramp * Rubber flooring on upper access slope left and right, approx. 860 mm long * Each side with 4 stake pockets (no stakes included), 2 t lashing option per pocket ----Chassis: * Chassis made of high-strength fine-grain steel ----Load Securing (Lashing Package): Rotary-platform: * 2 pairs 13.4 t lashing rings in the outer frame of the rotary-platform Low-bed: * Each side with 4 pairs 10 t retractable lashing rings on the outer frame, loadable in all directions * Each side rear with 2 pairs 13.4 t swing-away lashing rings ----Ramps: * Rubber surfacing on foldable loading ramps * Hydraulic folding ramps with hydraulically deployable ramp tips, approx. 4,650 x 720 mm * Hydraulic lateral ramp adjustment & load-holding valves ----Rear Support: * Hydraulic rear support ----Widening: * 8 pairs galvanized folding outriggers for 3 m overall width (not on rear ramp slope) * Extension planks stored in compartment on left side ----Excavator Arm Rest: * Excavator arm rest above rear axle to end of ramp, approx. L=2,100 mm x W=740 mm x H=190 mm * 2 pairs 6.4 t lashing rings on side of excavator arm rest ----Hydraulics: * Hydraulic flow divider in the trailer (for hydraulic pump output in truck over 40 up to max. 120 l/min) ----Loading dimensions: * Rear loading area: approx. 6,780 x 2,520 mm (incl. 860 mm ramp) * Area above turntable: approx. 2,990 x 2,520 mm ----Loading height: Bwjdpfx Aeylfvmepaop * Loaded: approx. 890 mm, +/- 20 mm ----Paintwork: * Reflective contour markings on sides and rear * Chassis, rotary-platform, ramps, and folding outriggers hot-dip galvanized * Axles, drawbar, air tanks, and turntable painted in black tone ----Info: * New vehicle with manufacturer's warranty * Errors and prior sale excepted * Sample images may show special equipment ----Delivery time: * Vehicle available from approx. week 23/2026