Used Faymonville Standard Body Trailers for sale (184)

Condition: new, maximum load weight: 50,400 kg, overall weight: 65,000 kg, axle configuration: > 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory, including units available immediately and at short notice, on our website. Excerpt from the equipment list. Full equipment specifications available on request. GOOSENECK * Gooseneck in SNT design to optimize loading platform length, approx. 3,700 mm long, with rear bevel approx. 1,000 mm x 10° * For tractor units: 4 x 2, 6 x 2, and 6 x 4 * Removable steel front wall, approx. 400 mm high * ASPÖCK-UNIBOX on the front connector strip with sockets * 3 kW electro-hydraulic unit for controlling hydraulic operations, excluding hydraulic winches * 1 pair of removable aluminum side boards, approx. 400 mm high, anodized finish * 1 removable aluminum tailgate, approx. 400 mm high, anodized finish * Approx. 40 mm thick hardwood floor above gooseneck, checker plate floor above king pin * 2-inch king pin * Rear section of gooseneck prepared for aluminum drive-on ramps * Round NATO socket on the front connection strip (Maeler & Kaege VG 96 917) LOADING PLATFORM * Extendable loading platform, approx. 8,800 mm long, with rear bevel approx. 500 mm x 10° * Recess in the loading platform and bevel for accommodating excavator dipper stick approx. 3,850 x 750 x 210/290 mm (L x W x H) * TPMS tire pressure monitoring system per ECE R 141 * BPW axles and suspension, 1st axle steerable, all remaining axles hydro-mechanically forced steered * 1st axle with electromagnetic reverse lockout, activated via reverse gear and manually * Technical axle load: 12,000 kg each, air suspension with raise and lower valve * Tires: 235/75 R 17.5, twin tires, 3PMSF * Mechanical landing legs with 2-speed gearbox and crank, JOST Module B – static test load approx. 50,000 kg * Continuous 50 mm thick hardwood floor on the loading platform and interrupted between axles (increases coefficient of friction) * 1 intermediate table, approx. 300 mm wide, for the extension tube with large cross-section * Extendable (galvanized) side extensions, approx. 230 mm per side (without wooden planks) * Wheel recesses with square climbing strips, approx. 15 x 15 mm ahead of axles, open through to gooseneck cross member, approx. 700 x 410 mm (W x D) * Aluminum covers for wheel recesses, usable as bridging elements for extension OR as widening planks * Aluminum elements lockable on telescopic tubes of the extensions * Widenable U-profiles for inserting ALU covers: - on the fixed section behind the gooseneck - on the intermediate table - on the extendable platform * Wheel recesses with square climbing strips, approx. 15 x 15 mm between 1st and 2nd axle, approx. 1,480 x 700 x 410 mm (L x W x D) * Aluminum covers for the wheel recesses, usable as bridging elements for the extension OR as widening planks * Aluminum elements lockable on the extension’s telescopic tubes * 1 pair of mechanical rear supports * Remote steering from front and rear via cable remote control, with axle tracking, without installation in the tractor unit HYDRAULIC LOADING RAMPS * One pair of two-section steel ramps, Type: DR-15/60-900-4350-KG-HV-M, approx. 4,350 mm in length and approx. 900 mm wide each Dedpotx Nwnefx Akkekn * Hydraulically foldable ramp tips * Ramps can be shifted hydraulically approx. 235 mm outward and approx. 215 mm inward individually * Super Grip rubber surface approx. 25 mm and steel plate surface approx. 5 mm as additional

Condition: new, maximum load weight: 33,865 kg, overall weight: 48,000 kg, axle configuration: 3 axles, Equipment: ABS, You can find our complete range of vehicles, including those available for immediate delivery or on short notice, on our website. Dksdpsw Tprzofx Akkjn Below is an excerpt from the specification. The full equipment list is available upon request. Gooseneck: * Gooseneck with front corners chamfered approx. 45° and a rear bevel approx. 750 mm x 10° * 3 pairs of lashing rings (LC 5,000 daN) * Hardwood flooring approx. 30 mm thick Load area: * Double extendable design with rear bevel approx. 500 mm x 8° * 6 pairs of folding external lashing rings (LC 5,000 daN) * 4 pairs of folding external lashing rings (LC 10,000 daN) * 1 pair of recessed lashing rings at the front of the loading area (LC 10,000 daN) * 1 intermediate table approx. 250 mm * Hardwood flooring approx. 48 mm thick, over axles with checker plate covering * Cut-outs in the external frame of the loading platform for attaching tie-down straps (LC 2,000 daN) Axles: * BPW axles and suspension, all axles forced-steered hydro-mechanically * Design axle load: 12,000 kg each * Air suspension with lift and lower valve * Axle tools included Tyres: * 245/70 R 17.5, load index (146/146 F) * Brand of our choice Landing legs: * JOST mechanical landing legs with 2-speed gearbox for approx. 24 t lifting capacity (approx. 50 t test load) Braking system: * Braking system according to EU regulations with EBS-E (2S2M) without connection lines to the tractor unit Paintwork: First-class and durable corrosion protection * High-quality, one-colour 2-component (2K) topcoat in RAL 3002 carmine red * Rear section metallized and coated in RAL 9010 (pure white) Steel Structure: Steel construction from high-strength fine grain steels. * Steel grades: S355J2+N/S355MC (yield strength 355 MPa), S690QL/S700MC (yield strength 690 MPa) Electrical system: * Electrical system according to EU regulations * 24 Volt lighting ASPÖCK-NORDIK (ASS3) * ASPÖCK-UNIBOX at the front connection strip with 24N, 24S & 15-pin sockets, compliant with ISO. 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Including the following additional equipment: * 2-inch kingpin * Galvanized steel front wall, approx. 400 mm high * Yellow-red air couplings at the galvanized front connection strip * Spare wheel carrier in front of the front wall * Electro-hydraulic unit * Rear and front steering via cable remote control with push-buttons, with single-track monitoring of the axles (without installation in the tractor unit) * Mount at the rear of the gooseneck for aluminum loading ramps * Removable aluminum ramp hanging rail at the rear of the vehicle * Galvanized folding supports beneath the slope of the load area * On the gooseneck: plug-in aluminum side boards and rear board, approx. 2,440 x 400 mm (L x H) * The rear galvanized stanchions are removable (body length approx. 2,560 mm) * One galvanized toolbox, integrated in the chamfered gooseneck * 4 pairs of WADER container pockets in the loading area for one 20', two 20', one 40' or one 45' container * 8 pairs of stanchion pockets (approx. 100 x 50 mm) in the external frame of the loading platform * Galvanized extensions, extendable by approx. 230 mm per side * Adjustable hanging rails for aluminum ramps at the rear of the vehicle * 2 pairs of ferry rings under the gooseneck and 2 pairs at the rear * Central lubrication system with 2 BEKAMAX (Pico) pumps, filled with standard grease NLGI-2 and removable pump guard * 2 LED reversing lights mounted on the rear panel * HRM Metallization (High Resistance Metallisa

Condition: new, maximum load weight: 39,720 kg, overall weight: 50,960 kg, axle configuration: > 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory, including immediately and short-term available vehicles, on our website. Sample equipment features. Full specification upon request. Gooseneck * With beveled front corners approx. 45° and rear bevel approx. 750 mm x 10° * 3 pairs of lashing rings (LC 5,000 daN) * Hardwood flooring, approx. 30 mm thick Loading Platform Loading platform in extendable design * 5 pairs of fold-out outer lashing rings (LC 5,000 daN) * 3 pairs of fold-out outer lashing rings (LC 10,000 daN) * 1 pair of recessed lashing rings at the front of the loading platform (LC 10,000 daN) * Recesses in the outer frame of the loading platform for securing straps (LC 2,000 daN) * Hardwood flooring approx. 48 mm thick, over axles with chequer plate covering Landing Gear * JOST (mechanical) with 2-speed gearbox, approx. 24 t lift capacity (approx. 50 t test load) Axles * BPW axles: 2 fixed axles, 2 steering axles, drum brakes * Air suspension with lift/lower function * Self-steering axle with electro-magnetic reverse lock, activated via reverse gear or manually * Tires: 205/65 R 17.5 Brake System * Wabco brake system in accordance with EU directives with EBS-E (4S3M), without interconnecting lines to the tractor unit Steel Construction * Made of high-strength fine-grained steels * Steel grades: S355J2+N/S355MC (yield strength 355MPa), S690QL/S700MC (yield strength 690MPa) Paintwork * First-class, durable corrosion protection of the standard shot-blasted welded frame, guaranteed by a 2-component (2K) zinc dust primer * High-quality 2-component (2K) top coat, single-color, RAL 3002 Carmine Red * Rear section metallized and painted in RAL 9010 (Pure White) * Rims in silver Accessories Included * 2-inch king pin * Galvanized front steel bulkhead approx. 400 mm high * Spare wheel holder in front of bulkhead * Yellow-red air couplings on galvanized connector bar front * 4 wheel chocks with holder at bulkhead * Bracket at rear of gooseneck for aluminum loading ramps * Galvanized folding supports under inclined edge of loading platform * Holder for beacon at rear of trailer * Yellow reflective tape on sides, extension, and rear in accordance with EU regulations * Brackets for warning signs with socket on both sides at the gooseneck and rear panel * TPMS tire pressure monitoring system per ECE R 141. Data transmission to the tractor unit via standardized EBS interface according to ISO 11992; for correct display, the tractor unit must support data transmission and display * Plug-in aluminum side walls and tailgate on gooseneck, approx. 2,440 x 400 mm (L x H); rear galvanized stakes are removable (body length approx. 2,560 mm) Djdpfeu Sd U Usx Akkskn * Galvanized toolbox, integrated in gooseneck slope * 6 pairs of WADER container locks in loading platform, for 1 x 20' container, 2 x 20' containers or 1 x 40' container * Sliding mounting rails for aluminum ramps at rear of vehicle * 7 pairs of stake pockets for plug-in stakes approx. 100 x 50 mm, in the outer frame of the loading platform * Galvanized cross bracket under the loading platform * Galvanized extendable widenings, extendable approx. 230 mm per side * Lift axle on front axle, controlled via TEBS E according to current axle load and load status * 5 pairs of recessed lashing rings along the central beam (LC 5,000 daN)

Condition: new, maximum load weight: 37,820 kg, overall weight: 48,000 kg, axle configuration: 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our entire vehicle inventory, including immediately and short-term available vehicles, on our website. Excerpt from the equipment. Full equipment details available upon request. Gooseneck: - Gooseneck with beveled front corners approx. 45° and rear chamfer approx. 750 mm x 10° - 3 pairs of lashing rings (LC 5,000 daN) - Hardwood floor covering approx. 30 mm thick Loading area: - 1 pair of fixed wheel recesses in front of the axles, approx. 2,610 x 970 x 400 mm (L x W x D) - Wheel recesses with square climbing slats approx. 15 x 15 mm and widenings in the lower section - Between the 1st and 2nd axles, a pair of fixed wheel recesses, approx. 1,610 x 700 x 400 mm (L x W x D) - Incl. 3-piece removable galvanized covers over the wheel recesses (W approx. 670 mm) – max. point load approx. 5 t/each - Recess in the chamfer and extending into the loading area for receiving the excavator bucket arm (approx. 2,900 x 750 x 210/290 mm (L x W x H)) - 1 pair of lashing rings, horizontal, at the front of the loading area (LC 10,000 daN) - 5 pairs of flip-out lashing rings (LC 5,000 daN) - 3 pairs of flip-out lashing rings (LC 10,000 daN) - 2 pairs of lashing rings in the excavator arm recess (LC 5,000 daN) - Cut-outs in the outer frame of the loading area for securing straps (LC 2,000 daN) One-piece Steel Ramps: - One pair of galvanized one-piece steel ramps, approx. 3,000 x 800 mm, with approx. 48 mm thick hardwood covering - Ramp with hydraulic lifting mechanism, hydraulically adjustable - Maximum load per pair: 40,000 kg - In accordance with Regulation 1230/2012/EU, ramps with a length less than 300 mm do not count towards the vehicle length in the driving position Landing gears: - JOST landing gears (mechanical) with 2-speed gearbox for approx. 24 t lifting capacity (approx. 50 t test load) Axles: - BPW axles and suspension, 2 fixed axles, 1 trailing steering axle - Technical axle load: 12,000 kg each - Electromagnetic reverse lock, activated via reverse gear and manually - Air suspension with lift and lower valve - Axle tool kit Tyres: - Tyres 235/75 R 17.5 3PMSF – manufacturer of our choice - TPMS tyre pressure monitoring system in accordance with ECE R 141. The data transmission to the truck is via standardized EBS interface according to ISO 11992. For correct display, the truck must be able to transmit and display this data Braking system: - WABCO braking system in accordance with EU regulations with EBS-E (2S2M) without connecting lines to the tractor unit Steel construction: - Steel structure made of high-tensile fine-grain steels - Steel grades: S355J2+N/S355MC (yield strength 355 MPa), S690QL/S700MC (yield strength 690 MPa) Electrical system: - Electrical system according to EU regulations Dsdpjw Tpqwjfx Akkjkn - Lighting 24 volts ASPÖCK-NORDIK (ASS3) - All LED side marker lights flash with the indicator - ASPÖCK-UNIBOX at the front connection strip with 24N, 24S & 15-pin sockets as per ISO. 24N ISO-1185, 24S ISO-3731, 15-pin ISO-12098 Paintwork: - Complete steel structure automatically shot-blasted with blasting wheel machine after welding - Second shot-blasting using corundum for optimal coating adhesion - HRM metallization of the entire vehicle chassis with ZINACOR 850 (85% zinc/15% aluminum) to ensure maximum corrosion protection - Final painting with 2 coats of two-component topcoat, single color in RAL 3002 Carmine Red, according to the RAL system 841GL - Rims in silver - Rear section metallized and in RAL 9010 (continuation see ori

Condition: new, maximum load weight: 52,810 kg, overall weight: 63,000 kg, axle configuration: > 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete range of immediately and soon available vehicles on our website. Excerpt from the equipment list. Full specifications available on request. Cargo area: * Cargo area with approx. 30 mm thick hardwood floor * 10 pairs of folding external lashing rings (LC 10,000 daN) Landing legs: * Hydraulic landing legs TPMS: * TPMS tire pressure monitoring system compliant with ECE R 141. Data transmission to the tractor unit is via the standardized EBS interface according to ISO 11992. For correct display, the tractor must be capable of transmitting and displaying these data. Dkjdpfxsxttc Ae Akkjn Axles and suspension: * BPW axles, technical capacity 12,000 kg each, first axle fixed, all others hydro-mechanically forced-steered, mounted on turntables * Air-suspended with lift and lower valve * Axle toolkit Tires: * Tires 445/65 R 22.5 169 K Electrical system: * Electrical system in accordance with EU regulations, lighting 24 Volt ASPÖCK-NORDIK (ASS3) * ASPÖCK-UNIBOX at the front connection strip with 24N, 24S & 15-pin sockets * Connections according to standards. 24N ISO-1185, 24S ISO-3731, 15-pin ISO-12098 Brake system: * Wabco brake system compliant with EU regulations, with EBS-E (4S3M), without connecting lines to the tractor unit Steel construction: * Steel construction made of high-strength fine-grain steels * Steel grades: S355J2+N/S355MC (yield point 355MPa), S690QL/S700MC (yield point 690MPa) Painting: * Complete steel structure automatically shot-blasted after welding using a shot-blasting machine * Secondary blasting with corundum for optimal adhesion of the coating system * Final painting with 2 coats of 2K topcoat, single color in RAL 1007 Narcissus Yellow according to RAL system 841GL * Rear section metallized and painted in RAL 9010 Pure White * Wheels in Silver Grey * Paint structure tested in salt spray test according to ISO 9227-NSS * Cavity sealing with special wax Including accessories: * Cargo area with approx. 30 mm thick hardwood floor * 2-inch king pin * One galvanized steel front wall (EN12642-XL), approx. 1,200 mm high * Yellow-red air couplings on the galvanized front connection strip * On the gooseneck and rear panel left and right, each with a bracket for warning signs including socket * Rear steering from the front and rear by cable remote control via push buttons, with single-track control of the axles (without installation in the tractor unit) * Electro-hydraulic unit * 12 pairs of stake pockets for approx. 100 x 50 mm stakes in the outer frame of the cargo area * Load manometer for determining axle loads including load diagram * Lift axle on the front axle, controlled by TEBS E * 5 pairs of crosswise stake pocket rails on the cargo area, for approx. 100 x 50 mm stakes * One INOX toolbox 1,200 x 460 x 550 mm mounted at the front left under the cargo area (in direction of travel) * 1 shunting coupling with reinforcement bolted to the rear cross member * BEKAMAX (Pico) automatic central lubrication system with standard grease NLGI-2 and removable pump guard * 2 LED reversing lights mounted on the rear panel * HRM metallization of the entire vehicle chassis with ZINACOR 850 (85% zinc/15% aluminum)

Condition: used, maximum load weight: 40,800 kg, overall weight: 53,800 kg, axle configuration: > 3 axles, first registration: 11/2012, next inspection (TÜV): 11/2025, Equipment: ABS, Faymonville 4-Axle Multimax STN-4AX Low Loader, extendable First registration: 11/2012 Unladen weight: 13,000 kg Gross weight: 53,800 kg Technically permissible: 55,400 kg Payload: 40,800 kg Kingpin load: 25,000 kg Tyres: 205/65R17.5 3rd and 4th axles with forced steering 4x SAF axles, 7,600 kg each, with air suspension Length: 13,475 mm up to 20,275 mm (extendable) Width: 2,540 mm up to 2,620 mm Height: 1,200 mm Further information available on request by email! Information is subject to change/errors excepted! Information provided online is for general description purposes only and does not represent a guaranteed specification. The seller is not liable for errors, input mistakes, or data transmission issues. Subject to modifications. Dsdpfxju Aynlj Akkokn Continuous purchase and sale as well as trade-in and rental of crane and lifting vehicles as well as construction machinery and heavy-duty vehicles.

Condition: reconditioned (used), functionality: fully functional, empty load weight: 20,000 kg, maximum load weight: 120,000 kg, axle configuration: 3 axles, tire condition: 70 %, color: red, Year of construction: 2006, 3 liftable and steerable axles. Hydraulic suspension Height-adjustable gooseneck Dodpfx Aoyaaz Hokkskn Hartz auxiliary petrol engine Independent wireless steering control Hydraulic rear ramps for machine loads up to 70 tons

Condition: ready for operation (used), machine/vehicle number: YAFTL40900001004, maximum load weight: 80,000 kg, overall weight: 105,000 kg, tire size: 70%, wheelbase: 1,360 mm, color: red, Year of construction: 2009, Equipment: ABS, Country of manufacture: Netherlands Body options : Disc brakes, Central lubrication system, Moving floor, Forced steering, Full side opening More information Low loader Pipe carrier, extendable, hydraulic suspension, laterally expandable up to 3500 mm interior and 4200 mm exterior, latest generation pendulum axles Dodpfxjvtygfs Akkjkn Option to incorporate 2-axis dolly to make 2 +4 pipe carrier equipment Load 85 tons We have 2 identical equipment in perfect condition.

Condition: used, maximum load weight: 65,350 kg, overall weight: 78,000 kg, axle configuration: > 3 axles, first registration: 05/2020, With air suspension, hydraulic dual-circuit forced steering (turntable) - "Platform" crane ballast design - Corners at right angles, closed external frame - Front linkage integrated into the frame - Fifth wheel plate with ball bearing slewing ring, replaceable 3.5" king pin and adjustable steering wedge - Fifth wheel load: 28,000 kg - Maximum steering angle: 2,700 mm Chassis - 5-axle chassis with air suspension including lift and lower valve - Axles: SAF brand - Tires: 445/65 R 22.5 Brake system - Two-line all-wheel compressed air brake system with diaphragm brake cylinders - Automatic load-dependent brake (ALB) - Automatic slack adjusters (AGS) - Parking brake via spring-loaded cylinders - Anti-lock braking system (ABS) - 1st and 2nd axles liftable (in direction of travel) Technical data Dsdpsx I U Eqofx Akkekn Cargo area (LxW): approx. 12,500 x 2,550 mm Coupling dimension B: 11,550 mm Loading height loaded (chassis area): approx. 1,490 mm at a loaded fifth wheel height: 1,200 mm Steering 1st axle: forced-steered 2nd axle: rigid 3rd - 5th axle: hydromechanical forced steering (dual-circuit steering) Radio remote control Electric power pack