Used Fliegl Zwp Trailers for sale (343)

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 6,950 kg, maximum load weight: 23,050 kg, overall weight: 30,000 kg, axle configuration: 3 axles, loading space length: 7,500 mm, loading space width: 2,520 mm, total length: 9,350 mm, total width: 2,550 mm, suspension: air, tire size: 235/75 R17,5", tire condition: 100 %, Customized transport solution Configure your Fliegl vehicle according to your requirements. The vehicle shown is an example. Production and equipment are customized according to customer specifications. Chassis – Central axle trailer design Fine-grained steel welded construction Gear-supported front leg Hydraulic rear supports Wheel chocks with holder Aluminum side impact protection Without under-run protection Mud flaps at the rear, covering the entire width Mud flaps in front of each axle and anti-splash mud flaps behind each axle Plastic tool box, with insert, w=620/h=360/d=440 mm, lockable with a padlock Extendable widening elements to 3,000 mm Storage compartment for wooden planks in the center + wooden planks 70 mm for widening to 3,000 mm Tie-down points for low-bed trailers Recessed ring-type tie-down points in the outer frame, each rated at 5 tons (can be converted to stake pockets) Tie-down eyes at the top and on the sides in the outer frame, each rated at 10 tons Towing device – Central axle trailer Drawbar with a tested 50 mm tow hitch Axles + Suspension Iisdezcv D Njpfx Ah Rjc Drum brake axles "Axles/chassis laser-aligned" – reduces tire wear and fuel consumption Last axle with trailing arm steering, with automatic reversing lock controlled via the reversing light, and an additional locking function on the vehicle via a manual button. Air suspension 1st axle – automatic lift axle, additionally manually lowerable, operable with a button on the vehicle Axle lift below the recommended driving height, therefore no guarantee for tire damage Braking system 2-line compressed air braking system, color-coded lines for easy servicing Spring-loaded parking brake 2 fail-safe coupling heads at the front, with connection lines to the towing vehicle EBS, electronic braking system with EBS connector at the front, with connection cable Note: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! With lifting and lowering valve Vehicle height in conjunction with the lift axle; when the lift axle is raised, the loading or overall height increases by 50 mm Vehicle – Driving stability system Trailer Info Center for displaying vehicle data such as axle loads, mileage, and diagnostic/system messages Axle load detection via EBS-CAN bus signal for display on the display in the cab Wheels and tires 235/75 R17.5, manufacturer's choice Steel rims, factory silver Electrical system 24 volts, multi-chamber lights in LED with resistor, yellow LED lighting on the sides, license plate lighting in LED 2 white position lights at the front in LED 2 white/red marker lights at the rear in LED 2 x 7-pin fail-safe plugs at the front, with connection cable Additional LED work light at the rear LED rotating beacon with mount Warning signs, LED illuminated and extendable to 3,000 mm Floor Subsequently with 70 mm softwood flooring, steel/diamond plate covering in the wheel arch area Rear slope with 70 mm softwood flooring Low-bed platform including rear slope 7,500 mm Ramps Steel ramps, 2,800 mm long, 750 mm wide, laterally adjustable Covered with wood Hydraulically operated via towing vehicle’s auxiliary drive with throttle, operation on the left side in the front Hydraulic lateral adjustment of the ramps, individually controllable Hydraulic connection with quick-release coupling NW 10/3, including connection hose Customized transport solution

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 4,995 kg, maximum load weight: 16,005 kg, overall weight: 21,000 kg, axle configuration: 2 axles, loading space length: 6,500 mm, loading space width: 2,520 mm, total length: 8,450 mm, total width: 2,550 mm, suspension: air, tire size: 235/75 R17,5", tire condition: 100 %, Custom-Made Transport Solution Configure your Fliegl vehicle to meet your specific requirements. The vehicle shown is an example. Production and equipment are customized according to customer specifications. Chassis: Center-Axle Trailer Fine-grained steel welded construction 2-speed gear-supported landing leg at the front Folding rear support 2 jockey legs with holder Aluminum side impact protection Splash flaps at the rear, spanning the entire width Quarter panel fenders in front of and behind each axle with anti-spray splash flaps according to EC regulations 1 aluminum storage box with stainless steel flap Container locking mechanism, 1 pair of recessed locking recesses in the floor for 1 x 20 ft container, 1 pair of container locking adapters Extendable widening sections to 3,000 mm Storage compartment for wooden planks in the center + wooden planks 70 mm for widening to 3000 mm Tie-down points, low-bed trailer 1 pair of tie-down brackets additionally at the front in the front cross member, 10 tons each 5 pairs of ring tie-down points recessed in the outer frame, 5 tons each (can be converted to stake pockets) 7 pairs of tie-down cleats recessed on top and on the side in the outer frame, 10 tons each Iodpfxozcvt Rj Ah Reic Coupling system, center-axle trailer Drawbar with tested 50 mm tow hitch Axles + Suspension Drum brake axles, according to the manufacturer's choice "Axle/chassis laser aligned" reduces tire wear and fuel consumption Axle distance 1810 mm Air suspension Braking system 2-line compressed air braking system Color-coded line routing for easy servicing Spring-loaded parking brake 2 fail-safe coupling heads at the front, with connection lines to the towing vehicle Parking sockets for ABS/EBS and air connection on the drawbar or drawbar 24 Volt EBS, electronic braking system with EBS connector at the front with lift and lower valve Vehicle - driving stability system Axle load recognition via EBS-CAN bus signal, for display on the display in the cab "TPMS" Tire Pressure Monitoring System according to ECE R 141, display on the display in the towing vehicle, via EBS Wheels and Tires 235/75 R17.5, manufacturer's choice Protective caps for wheel studs Electrical System 24 Volt, multi-chamber lights in LED, yellow LED lighting on the side, license plate lighting in LED Yellow LED lighting on the side, coupled with the turn signal "Flashing side marker lights" Premium LED side marker lights, with "20 LED diodes per light" 2 white position lights at the front in LED 2 white/red outline lights at the rear in LED 2 x 7-pole fail-safe plugs at the front, with connection cable Parking sockets for electrical system on the drawbar LED work lights on both sides 2 additional LED work lights at the rear 1 LED rotating beacon with holder, switched via sidelights 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor thereafter with approx. 70 mm soft wood flooring, in the wheel arch area steel/diamond plate flooring Rear inclination with "Mega Grip surface" made of interlocking grating Low-bed area including rear inclination 6,500 mm Front panel / corner posts Aluminum profile, approx. 400 mm high, plug-in Ramps Steel ramps 2,800 mm long, 750 mm wide, laterally movable Ramp surface with "Mega Grip" made of interlocking grating Hydraulically operated via towing vehicle auxiliary drive with throttle, operation on the left side Hydraulic side displacement of the ramps, individually controllable Hydraulic connection with quick-release cou

Condition: used, maximum load weight: 6,100 kg, overall weight: 8,900 kg, axle configuration: 2 axles, first registration: 10/1998, loading space length: 6,200 mm, loading space width: 2,480 mm, loading space height: 2,750 mm, loading space volume: 42 m³, total width: 2,550 mm, total height: 4,000 mm, Year of construction: 1998, 2-Axle Fliegl TPS 89 Pr.+Pl. Trailer with Drop Sides VIN: W1F20917 Chassis / Attachments: Iiodpfx Aey Rgyroh Rsc * Air suspension with lift/lower function * Tyres: 215/75 R17.5 * Tread depth remaining: front approx. 30/60%, rear approx. 70/40% * Spare wheel holder * 1x Haacon landing leg * 2x rear support legs Body: * Fliegl Pr.+Pl. with drop sides * 60 cm side walls * 4x lashing eyes per side * Dimensions: 6,200 mm x 2,480 mm x 3,020 mm * Approx. 68 m³, 22 pallets Weights: * Gross weight: max 8,900 kg – reduced to 4,500 kg * Unladen weight: 2,800 kg * Payload: 6,100 kg Other: * German vehicle New main inspections/safety tests or changes to weight ratings (up- or downrating) available on request. We are happy to assist with export/transfer number plates, as well as organising the transfer of your purchased vehicles within Germany. Contact us! — We speak the following languages: German, English, and Russian! — No liability for printing or typing errors. Subject to change, prior sale or errors! — Who are we? Leible Nutzfahrzeuge is a family business located in Kehl am Rhein. With our many years of experience in preparing and marketing commercial vehicles, we are a reliable partner for customers worldwide. Leible Nutzfahrzeuge is particularly strong in the sale of new and used commercial vehicles. Our 11,000 m² premises host a wide range of vehicles. Our business philosophy is based on fairness and integrity. As customer satisfaction is very important to us, we offer an excellent all-round service package and provide you with a competent contact partner who will assist you with the purchase or sale of vehicles. See for yourself! Our service for you: Vehicle loading We are happy to assist you in loading your purchased vehicles. Organising special transports We are happy to help you organise special transports. Short-term/export number plates We are happy to assist in obtaining export/temporary plates. Customs formalities We are happy to assist you with customs procedures.

Condition: used, overall weight: 35,000 kg, axle configuration: 3 axles, first registration: 05/2015, loading space length: 13,600 mm, loading space width: 2,520 mm, Equipment: ABS, Schmitz Cargobull S01 Flatbed with Lifting Axle and SAF Axles Ref. No. for inquiries: 1225958 Iisdpfxoyavigo Ah Rec * ABS * EBS * 3 axles, air-suspended * Lifting axle * Disc brakes * SAF axles Loading area dimensions: Length: 13,600 mm Width: 2,520 mm Tyres: 1st axle: 385 / 55 R 19.5 30% air-suspended / lifting axle 2nd axle: 385 / 55 R 19.5 30% air-suspended 3rd axle: 385 / 55 R 19.5 30% air-suspended ----Price: €3,900 + 19% VAT For further questions, you can reach us at the following phone numbers: * We speak: German, English, French, Polish, and ????? Errors, omissions, and prior sale reserved.

Condition: used, overall weight: 35,000 kg, axle configuration: 3 axles, first registration: 08/2013, loading space length: 13,600 mm, loading space width: 2,520 mm, Equipment: ABS, Schmitz Cargobull S01 Platform Lift Axle Aluminum Side Walls Stakes STEEL TRANSPORTS Internal Reference Number for inquiries: 0326236 * ABS * EBS * 3 axles air-suspended * Lift axle * Disc brakes * BPW axles * Aluminum side walls * Stakes Loading area length: Length: 13,600 mm * Width: 2,520 mm Tires: 1st axle: 385 / 65 R 19.5 20% air-suspended / lift axle 2nd axle: 385 / 65 R 19.5 20% air-suspended Isdpfx Ahjyulw Nj Rjic 3rd axle: 385 / 65 R 19.5 20% air-suspended ---Price: 9,900 EUR + 19% VAT For further questions, you can reach us at the following phone numbers: * We speak: German, English, French, Polish, and ????? Subject to typing errors, errors, and prior sale.

Condition: used, empty load weight: 5,100 kg, maximum load weight: 32,900 kg, overall weight: 38,000 kg, axle configuration: > 3 axles, first registration: 08/2018, suspension: air, tire size: 385/55 22,5, tire condition: 50 %, color: other, Year of construction: 2018, front tire size: 385/55 22,5, rear tire size: 385/55 22,5, driver cabin: day cab, emission class: none, Equipment: ABS, truck registration, Reference number for inquiries: 69803 Fliegl, SDS01 * Year of manufacture: 2018 * ABS, Anti-lock Braking System * EBS, Electronic Braking System * Air suspension * Lift axle * Air connection couplings (red and yellow) * 15-pin connector plug * Lifting and lowering mechanism * Suspension: Air * Total weight: 38,000 kg Ijdpfx Aoyib Iqeh Rjic * Unladen weight: 5,100 kg * Payload: 32,900 kg * Permissible total weight: 38,000 kg * Axle manufacturer: SAF * Tyre condition 1st axle: 70% – 70% – Tyre size: 385/55 R22.5 * Tyre condition 2nd axle: 30% – 30% – Tyre size: 385/55 R22.5 * Tyre condition 3rd axle: 50% – 50% – Tyre size: 385/55 R22.5 * Tyre sizes: 385/55 R22.5 * Fliegl container chassis * 40" container platform for timber and metal, manufacturer: S Grabmeier * Unladen weight: 4,600 kg, front wall height: 2,040 mm * 6 pairs of lashing rings for rail transport * Frame height: 500 mm, wooden superstructure with 8 pairs of Ecco Steel stanchions on container chassis * Stanchion height: 1,980 mm * Special features: Lift axle / timber transport / SAF axle Disclaimer: Subject to change, prior sale and errors excepted. More photos and videos can be found on our website. Our comprehensive services include for example: * Purchase / sale / rental of commercial vehicles * Fast, easy financing options * Processing of all (export) documents * Ordering of export plates / customs plates * Vehicle preparation: new tarpaulins, signage, painting, etc. * Professional loading / cargo securing * TÜV inspections, registration services * Transfer of commercial vehicles Ask our trained staff, we are happy to advise you.

Condition: used, empty load weight: 5,100 kg, maximum load weight: 32,900 kg, overall weight: 38,000 kg, axle configuration: > 3 axles, first registration: 08/2018, suspension: air, tire size: 385/55 22,5, tire condition: 60 %, color: other, Year of construction: 2018, front tire size: 385/55 22,5, rear tire size: 385/55 22,5, driver cabin: day cab, emission class: none, Equipment: ABS, truck registration, Reference number for inquiries: 69805 Fliegl, SDS01 * Year of manufacture: 2018 * ABS, Anti-lock Braking System * EBS, Electronic Braking System * Air suspension * Lift axle * Air line coupling head (red + yellow) * 15-pin connector plug * Raise and lower device * Suspension: Air * Gross weight: 38,000 kg * Unladen weight: 5,100 kg * Payload: 32,900 kg * Permissible gross weight: 38,000 kg * Axle manufacturer: SAF * Tire condition, 1st axle: 70% -- 70% - Tire size: 385/55 R22.5 * Tire condition, 2nd axle: 50% -- 50% - Tire size: 385/55 R22.5 * Tire condition, 3rd axle: 50% -- 50% - Tire size: 385/55 R22.5 * Tire sizes: 385/55 R22.5 * Fliegl container chassis Ijdpfxjyib Ide Ah Roic * 40" container platform for timber & metal, manufacturer: S Grabmeier * Unladen weight: 4,600 kg, front wall height: 2,040 mm * 6 pairs of lashing rings for rail transport * Frame height: 500 mm, timber body with 8 pairs of Ecco Steel stanchions on container chassis * Stanchion height: 1,980 mm * Highlight: Lift axle / timber transport / SAF axles Disclaimer: Subject to change, prior sale, and errors excepted. You can find further photos and videos on our website. Our comprehensive service portfolio includes, for example: * Purchase / sale / rental of commercial vehicles * Fast, straightforward financing solutions * Application for all (export) documentation * Ordering of export/temporary customs license plates * Vehicle preparation: new tarpaulins, lettering, repainting, etc. * Professional loading and load securing * TÜV inspections, registration service * Transfer of commercial vehicles Please contact our trained specialist staff—we will be happy to advise you.

Condition: used, empty load weight: 5,100 kg, maximum load weight: 32,900 kg, overall weight: 38,000 kg, axle configuration: > 3 axles, first registration: 08/2018, suspension: air, tire size: 385/55 22,5, tire condition: 60 %, color: other, Year of construction: 2018, front tire size: 385/55 22,5, rear tire size: 385/55 22,5, driver cabin: day cab, emission class: none, Equipment: ABS, truck registration, Reference number for inquiries: 69804 Fliegl, SDS01 * Year of manufacture: 2018 * ABS, Anti-lock Braking System * EBS, Electronic Braking System * Air suspension * Lift axle * Air connection coupling head (red + yellow) * 15-pin connector plug * Lifting and lowering device * Suspension: Air * Gross weight: 38,000 kg * Unladen weight: 5,100 kg * Payload: 32,900 kg * Permissible total weight: 38,000 kg * Axle manufacturer: SAF * Tire condition, 1st axle: 70% -- 70% - Tire size: 385/55 R22.5 * Tire condition, 2nd axle: 50% -- 50% - Tire size: 385/55 R22.5 * Tire condition, 3rd axle: 50% -- 50% - Tire size: 385/55 R22.5 * Tire sizes: 385/55 R22.5 * Fliegl container chassis * 40" container platform for wood & metal * Manufacturer: S Grabmeier * Unladen weight: 4,600 kg * Front wall height: 2,040 mm * 6 pairs of lashing rings for rail transport * Frame height: 500 mm * Timber body with 8 pairs of Ecco Steel stanchions on container chassis * Stanchion height: 1,980 mm * Highlights: Lift axle / Timber transport / SAF axle Disclaimer: Subject to change, prior sale, and errors excepted. You can find more photos and videos on our website. Iijdpfxsyib H To Ah Rec Our comprehensive service includes, for example: * Purchase / sale / rental of commercial vehicles * Fast, straightforward financing * Processing of all (export) documents * Ordering of export license plates / customs plates * Vehicle preparation: new tarpaulins, lettering, painting, etc. * Professional loading / load securing * TÜV inspections, registration service * Vehicle transfer of commercial vehicles Please contact our trained staff – we will be happy to advise you.

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 3,135 kg, maximum load weight: 8,665 kg, overall weight: 11,800 kg, axle configuration: 2 axles, loading space length: 6,200 mm, loading space width: 2,480 mm, total length: 8,350 mm, total width: 2,550 mm, suspension: steel, tire size: 235/75 R17,5", tire condition: 100 %, Customized transport solution Configure your Fliegl vehicle according to your requirements. The vehicle shown is an example. Production and equipment are carried out individually according to customer requirements. Fine-grained steel welded construction Outer frame slightly inclined with "Load-Lock profile" for attaching lashing straps Gearbox support at the front Foldable rear support 2 chock blocks with holder Under-ride guard, steel, galvanized Splash flaps at the rear, covering the entire width Quarter panel fenders according to EC standards with anti-spray splash flaps according to EC standards 1 plastic toolbox, w=600 / h=425 / d=460 mm, lockable Storage compartment for lashing equipment, open, under the loading area 4 lashing/spar bars recessed in the floor, running transversely across the entire width to the outer frame (max. usable inner width between the outer spar bars approx. 2170 mm), approx. 100 mm high. With 20 mm round steel bars, top and bottom, spacing from top to bottom approx. 60 mm (of the round steel). Bottom with an angle plate as a closure, open halfway downwards. For lashing and inserting spar bars 80 x 80 mm. 4 pairs of spar pockets recessed in the outer frame, internal dimensions 83 x 83 mm 4 spar pockets recessed in the center of the floor, with reinforcements to the main frame, internal dimensions 83 x 83 mm 6 pairs of spar bars, W=80/ D=80/ L=2000 mm, hot-dip galvanized Note: Spar pockets/insertions are not designed for the sole securing of long materials, pipes, etc. without wrapping around. Side impact protection, aluminum Coupling device, tandem trailer Drawbar with tested 40 mm towing eye Drawbar mechanically adjustable in length by 4 x 500 mm, from 1800 - 3800 mm, drawbar length set to 1800 mm Axles + Suspension Axles according to manufacturer's choice, with tapered roller bearings and S-cam brake "Axle/chassis laser measured" reduces tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearing and mechanical axle load compensation (rocker arm compensation) Wheels and tires 235 / 75 R 17.5" according to manufacturer's choice Steel rims, factory silver Braking system 2-line compressed air braking system Spring brake parking brake Integral air reservoir 2 fail-safe coupling heads at the front, with connecting lines to the towing vehicle, ABS and ALB, with ABS connector at the front, with connecting cable Note: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Iisdpfxsi Ri H Do Ah Roc Electrical system 24 Volt, multi-chamber lights in LED, yellow LED lighting on the sides, license plate lighting in LED, (Note! with certain towing vehicles, false diagnoses may occur, although the function is given) 2 white position lights at the front in LED 2 white/red side marker lights at the rear in LED 2 x 7-pole fail-safe plugs at the front, with connecting cable Floor Plywood panels, approx. 30 mm thick, for high point load capacity Note: Floor deflection due to weather influences is possible! Platform length approx. 6,200 mm Operating instructions Special permit required if the overall length of the combination exceeds 18,750 mm. Observe country-specific registration regulations. Approval / Signs Country of registration: Germany with Dekra inspection and certificate Contour marking with reflective tape according to ECE R 048, white on the sides and red at the rear Paintwork Frame hot-dip galvanized including passivation "15-year warranty against rust perforation

Condition: used, THREE-POINT HITCH WEIGHING SYSTEM, DIGITAL 010 Fliegel three-point hitch weighing system 020 complete with adapter 030 load cells and display Iisdezbyyxepfx Ah Rec

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 2,900 kg, maximum load weight: 8,900 kg, overall weight: 11,800 kg, axle configuration: 2 axles, loading space length: 6,200 mm, loading space width: 2,480 mm, total length: 8,000 mm, total width: 2,550 mm, total height: 3,000 mm, suspension: steel, tire size: 235/75 R17,5", tire condition: 100 %, Customized Transport Solution Configure your Fliegl vehicle to meet your specific requirements. The vehicle shown is an example. Production and equipment are tailored to individual customer needs. Chassis: Center-axle trailer Fine-grained steel welded construction Outer frame slightly angled, new design with "Load-Lock profile" for tie-down straps 3 pairs of lashing eyes outside in the floor, each 5 tons 1 at the front in the corners, 1 in front of and 1 in the rear incline at the back 6 pairs of lashing eyes outside in the floor/outer frame, each 5 tons Gearbox support leg at the front Rear support, foldable 2 wheel chocks with holder Aluminum side impact protection Steel underrun protection, galvanized Splash guards at the rear covering the entire width (not in combination with forklift mount) Quarter panel fenders 1 plastic toolbox, w=600 / h=425 / d=460 mm, lockable Coupling device: Center-axle trailer Drawbar with tested 40 mm drawbar eye Drawbar height-adjustable via spindle, max. adjustment range 300 mm Axles + Suspension GFA or BPW axles, at the manufacturer's choice, with tapered roller bearing and S-cam brake "Axle/chassis laser-aligned" - reduces tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearing and mechanical axle load compensation (lever compensation) Braking System 2-line compressed air brake system Color-coded line routing for easy servicing Hand-spindle parking brake 2 fail-safe coupling heads at the front, with connecting lines to the towing vehicle 24 volt ABS and ALB, with ABS connector at the front, with connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Wheels and Tires 235/75 R17.5, manufacturer's choice Steel rims, factory silver Electrical System 24 volt, multi-chamber lights, yellow LED lighting on the sides 2 white position lights at the front, in LED 2 white/red marker lights at the rear 2 x 7-pole fail-safe plugs at the front, with connecting cable Iijdszcqpaspfx Ah Rsc Floor Steel/diamond plate floor for high point load capacity Note: Slight floor waviness due to welding distortion is possible! Platform length approx. 6,200 mm Rear incline to approx. 900 mm Front wall / corner posts at the front 25 mm aluminum hollow profile, 400 mm high Side walls 25 mm aluminum hollow profile, 400 mm high, foldable and removable Rear wall / corner posts at the rear 1 pair of steel uprights attached to the frame, with brackets for locking the access ramps, access width approx. 2,430 mm Access Ramps Steel ramps 2,300 mm long, 510 mm wide, laterally movable With handrail on the ramps Covered with wood (tip area with steel/diamond plate) With gas spring for one-person operation Operating Instructions The stated total weight is technically possible; depending on the cargo, the total weight may not be reached while complying with the permissible axle/support and saddle loads. (Poor driving and following behavior possible due to incorrect load distribution) Country of Registration / Signs Germany With DEKRA inspection and certificate (according to §13 EG - FGV) 24/7 service hotline Prepared for single-row license plate holder Contour marking with reflective strips according to ECE R 048, white on the sides and red at the rear Paintwork Frame DB 7350 Novagrau "10-year warranty against rusting" Front wall Aluminum Side wall Aluminum, anodized Access ramps Hot-dip galvanized Customized Transport Solution

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 4,300 kg, maximum load weight: 13,700 kg, overall weight: 18,000 kg, axle configuration: 2 axles, loading space length: 6,900 mm, loading space width: 2,480 mm, loading space height: 2,740 mm, total length: 8,685 mm, total width: 2,550 mm, total height: 3,970 mm, suspension: air, tire size: 385/65 R22,5", tire condition: 100 %, Customized transport solution Configure your Fliegl vehicle to meet your requirements. The vehicle shown is an example. Production and equipment are tailored to individual customer needs. Chassis: Center axle trailer Fine-grained steel welded construction Outer frame slightly angled with "Load-Lock profile" for attaching tie-down straps. Note: To attach the straps, the side panels must be opened! "Vario-Lash" lashing rings for use in the "Load-Lock profile", 2.5 tons each, loose Gear-supported front legs, with a straight lower part and single-sided operation on the right Telescopic rear support Retractable ladder at the rear Door latch on the side Chocks with holder Aluminum side impact protection Steel underrun protection Quarter panel fenders in front of and behind each axle Rear impact protection Plastic toolbox with drawer and insert, w=650 / h=520 / d=670 mm, lockable with a padlock Coupling device for center axle trailer, according to customer requirements Axles + Suspension SAF disc brake axles with 430 mm disc diameter "Axle/chassis laser-aligned" to reduce tire wear and fuel consumption Air suspension Braking system 2-line compressed air braking system, color-coded lines for easy maintenance Spring-loaded parking brake Duomatic connection at the front, with connection line to the towing vehicle Iijdpfjzcqh Nsx Ah Rec EBS, electronic braking system with EBS plug at the front, with connection cable Caution: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with raise and lower valve Vehicle – driving stability system Wheels and tires 385/65 R22.5", manufacturer's choice Steel rims, factory silver Electrical system 24 Volt, multi-chamber lights, yellow LED lighting on the sides 2 white position lights at the front 2 white/red side marker lights at the rear 1 x 15-pole plug at the front, with connection cable Floor Sieve-printed panels, approx. 30 mm thick, for high point load capacity Platform length approx. 6,900 mm Front bulkhead / corner posts at the front 2,580 mm high, steel corner posts in a full-volume design, release mechanism for side tarpaulin on the front bulkhead Center posts Sliding posts, can be moved along the entire length, with 4-fold insertion pockets and a long pocket at the bottom Insertion slats Rows of aluminum V-insertion slats Rear bulkhead / corner posts at the rear Rear corner posts, steel up to the lower edge of the roof, attachment for tarpaulin with round tube and tarpaulin tensioner Rear portal doors, 2-wing, each with 2 internal rotating bar locks Tarpaulin Tarpaulin with welded horizontal and vertical straps Tensioners made of stainless steel Customer lettering on side tarpaulins and rear portal possible Roof Fixed roof with tarpaulin and bows, tarpaulin color: white Optimal rain gutter at the rear, at the top of the end bow, above the doors Registration country / signs Germany with Dekra inspection and certificate (according to §13 EG - FGV) Load securing certificate according to EN 12642 XL 24/7 service hotline prepared for license plate holder, single row Reflective strips: white, continuously on the side tarpaulin at the bottom and at the top in the corners (if visible side panels, then the strip at the bottom, on the side panels) Reflective strips: red, around the rear portal *also available as a drive-through version Customized transport solution

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 3,200 kg, maximum load weight: 8,600 kg, overall weight: 11,800 kg, axle configuration: 2 axles, loading space length: 7,300 mm, loading space width: 2,480 mm, total length: 9,490 mm, total width: 2,550 mm, total height: 3,900 mm, suspension: air, tire size: 235/75 R17,5", tire condition: 100 %, Custom-Made Transport Solution Configure your Fliegl vehicle to meet your specific requirements. The vehicle shown is an example. Production and equipment are tailored to individual customer needs. Type: TPS 118 Logistics Semi-Trailer Chassis: Central Axle Trailer Outer frame slightly inclined, new design with "Load-Lock profile" for securing tie-down straps 2-speed gear support leg at the front Plastic toolbox Platform height: 1080 mm Coupling: Central axle trailer Drawbar with tested 40 mm drawbar eye, logistics version Drawbar mechanically adjustable in height via threaded spindle, below floor level, max. adjustment range 200 mm Drawbar mechanically adjustable in length from approx. 1950 - 2300 mm, can be mechanically locked at approx. 50 mm intervals, drawbar length set to approx. 2100 mm Axles & Suspension SAF/BPW axles, selectable by the manufacturer "Axle/chassis laser-aligned" to reduce tire wear and fuel consumption Air suspension Braking System 2-line pneumatic braking system Spring-loaded parking brake Duomatic connection at the front, with connection line to the towing vehicle 24 Volt EBS, electronic braking system with EBS plug at the front, with connection cable with raising and lowering valve Vehicle - Driving Stability System Wheels and Tires 4x 235/75 R17.5, brand selectable by the manufacturer 4x steel rims, factory silver Electrical System 24 Volt, multi-chamber lights, yellow LED lighting on the sides 2 white position lights at the front 2 white/red side marker lights at the rear 1 x 15-pin plug at the front, with connection cable Floor Sieve-printed panels, approx. 30 mm thick, for high point load capacity Platform length: approx. 7,300 mm Superstructure Front wall / corner posts at the front Through-loading system with front portal doors, 2-leaf, each with 2 internal rotary bolt locks, corner posts made of steel, release mechanism for side tarpaulin Ramp, approx. 2,400 mm wide, 1 x divided, approx. 350 mm long for resting on the tailgate, load capacity approx. 1,800 kg, incl. support for the tailgate (drawbar length then approx. 2100 mm, for tailgate length of 1800 mm, the coupling offset from the truck must be at least 20 to max. 240 mm). Note! Usable internal length is reduced by the ramp! Side Walls Center Rails 2 pairs of sliding rails that can be moved along the entire length, with 4 pockets and a long pocket at the bottom Insert strips 5 rows of wooden insert strips (in combination with side walls, 4 rows) Ijdpozcp E Tefx Ah Rsic Rear Wall / Corner Posts at the Rear Corner posts at the rear made of steel, extending to the lower edge of the roof, attachment for tarpaulin with round tube and tarpaulin tensioning ratchet Rear portal doors, 2-leaf, each with 2 internal rotary bolt locks Tarpaulin Tarpaulin with welded-in horizontal and vertical straps Tensioning fasteners made of stainless steel Customer lettering on side tarpaulins and rear portal possible Roof Sliding tarpaulin, rear end lift that can be folded up, with the tarpaulin sliding from back to front, tarpaulin color: white Optimal rain gutter at the rear, above at the end beam, above the doors Country of Registration / License Plates Germany with Dekra approval and certificate (according to §13 EG - FGV) Fliegl manufacturer certificate for the structural strength of the superstructure according to EN 12642 XL prepared for single-line license plate holder Reflective strips: white, continuous on the bottom of the side tarpaulin and at the top in the corners Reflective strip

Condition: used, Year of construction: 2023, working width: 680 mm, Equipment: lighting, Disc diameter: 35 cm, trailed, hydraulic folding, support foot/wheel. Working width: 6.80 m, hydraulic folding. Disc diameter: 350 mm. Air brake system. Lighting, hydraulic side shift, load sensing. Control block incl. control panel. Location: customer. Iodpfxsyygl Hs Ah Rjic

Condition: used, maximum load weight: 31 kg, overall weight: 31,000 kg, tire size: 750/50R26.5, Year of construction: 2024, front tire size: 750/50R26.5, rear tire size: 750/50R26.5, operation weight: 31,000 kg, Equipment: compressed air brake, Tyres (front): 750/50R26.5, Tyres (rear): 750/50R26.5, Steering axle, Automatic tailgate, Support foot / wheel, Tandem axle, Underslung hitch (eye)_____Tridem, 1st & 3rd axle steered, hydraulically sprung drawbar, underslung hitch, K80, 40 km/h, permissible gross weight 31 t, Location: customer Iedeyr U Niopfx Ah Reic

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 2,200 kg, maximum load weight: 8,300 kg, overall weight: 10,500 kg, axle configuration: 2 axles, loading space length: 4,500 mm, loading space width: 2,050 mm, loading space height: 400 mm, total length: 6,280 mm, total width: 2,550 mm, total height: 2,900 mm, suspension: steel, tire size: 235/75 R17,5", tire condition: 100 %, Customized transport solution Configure your Fliegl vehicle according to your requirements. The vehicle shown is an example. Production and equipment are carried out individually according to customer requirements. Chassis, central axle trailer, low-bed Fine-grained steel welded construction Gear-supported front leg Iedpji Ri Ebefx Ah Roic Telescopic rear support 2 chock blocks with holder Fenders made of steel sheet over both wheels Aluminum side impact protection Coupling device for central axle trailer Drawbar with tested 40 mm drawbar eye Drawbar height-adjustable via spindle, max. adjustment range 250 mm Axles + Suspension BPW drum brake axles "Axle/chassis laser-aligned" – reduces tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearing and mechanical axle load compensation (rocker compensation) Wheels and tires 235 / 75 R 17.5" according to manufacturer's choice Steel rims, factory silver Braking system 2-line compressed air braking system Spring-loaded parking brake 2 fail-safe coupling heads at the front, with connecting lines to the towing vehicle 24 Volt ABS and ALB, with ABS plug at the front, with connection cable Note: The trailer may only be towed by towing vehicles that ensure the effectiveness of the ABS! Electrical system 24 Volt, multi-chamber lights, yellow LED lighting on the sides 2 white position lights at the front 2 white/red side marker lights at the rear 2 x 7-pole fail-safe plugs at the front, with connection cable Platform TTS Low-lying steel pan, platform floor made of steel/diamond plate, steel walls welded to the floor Platform length 4500 mm Pan with "Load-Lock profile" at the front and on the sides for attaching lashing straps (8 pieces at the front, 12 pieces on each side) Note: Slight unevenness in the floor may occur due to welding distortion! 2 pairs of lashing eyes, 1 x at the front in the corners of the steel pan and 1 x at the rear in the floor, each 5 tons. Loading ramps Steel ramps 2,300 mm long, 510 mm wide, laterally adjustable with handrail on the ramps covered with wood (tip area with steel/diamond plate) with gas spring for single-person operation Operating instructions The specified total weight is technically possible, but depending on the load, the total weight may not be reached while observing the permissible axle/support and saddle loads. (Poor driving and tracking behavior possible due to incorrect load distribution) Country of registration/Signs Country of registration: Germany with Dekra inspection and certificate (according to §13 EG - FGV) 24/7 service hotline prepared for single-line license plate holder Contour marking with reflective tape according to ECE R 048, white on the sides and red at the rear Painting Frame painted or galvanized, according to customer request Loading ramps, hot-dip galvanized Customized transport solution Configure your Fliegl vehicle according to your requirements. The vehicle shown is an example. Production and equipment are carried out individually according to customer requirements.

Condition: new, functionality: fully functional, machine/vehicle number: WFDFLT21001014667, empty load weight: 2,200 kg, maximum load weight: 8,300 kg, overall weight: 10,500 kg, axle configuration: 2 axles, loading space length: 4,500 mm, loading space width: 2,050 mm, loading space height: 400 mm, total length: 6,280 mm, total width: 2,550 mm, total height: 2,900 mm, suspension: steel, tire size: 235/75 R17,5", tire condition: 100 %, color: silver, Chassis: Center-axle semi-trailer, low-bed Fine-grain steel welded construction Telescopic support leg at the front Telescopic rear support 2 chock blocks with holder Fenders made of sheet steel over both wheels Side impact protection, aluminum Coupling device for center-axle semi-trailer Drawbar with tested 40 mm drawbar eye Drawbar height-adjustable via spindle, max. adjustment range 250 mm Axles + Suspension BPW drum brake axles "Axles/chassis laser-aligned" – reduces tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearing and mechanical axle load compensation (lever system) Wheels and Tires 235 / 75 R 17.5" according to manufacturer's choice Steel rims, factory silver Braking System 2-line compressed air braking system Spring-loaded parking brake 2 fail-safe coupling heads at the front, with connecting lines to the towing vehicle Iijdszcnzaspfx Ah Rec 24 Volt ABS and ALB, with ABS plug at the front, with connecting cable Caution: The trailer may only be pulled by towing vehicles that guarantee the effectiveness of the ABS! Electrical System 24 Volt, multi-chamber lights, yellow LED lighting on the sides 2 white position lights at the front 2 white/red side marker lights at the rear 2 x 7-pole fail-safe plugs at the front, with connecting cable Platform TTS Low-lying steel platform, platform floor made of steel/checkered plate, steel walls solidly welded to the floor Platform length 4500 mm Platform front and sides with "Load-Lock profile" for attaching lashing straps (8 pieces at the front, 12 pieces on each side) Note: Slight unevenness of the platform possible due to welding distortion! 2 pairs of lashing eyes, 1 x at the front in the corners of the steel platform and 1 x at the rear in the floor, 5 tons each Ramps Steel ramps, 2,300 mm long, 510 mm wide, laterally adjustable with handrail on the ramps covered with wood (tip area with steel/checkered plate) with gas spring for single-person operation Operating Instructions The stated total weight is technically possible; depending on the load, the total weight may not be reached while complying with the permissible axle/support and saddle loads. (Poor driving and handling characteristics possible due to incorrect load distribution) Country of Approval / Signage Country of Approval: Germany with DEKRA inspection and certificate (according to §13 EG - FGV) 24/7 service hotline prepared for single-row license plate holder Contour marking with reflective strips according to ECE R 048, white on the sides and red at the rear Painting Frame: Hot-dip galvanized, including passivation "15 years warranty against rust" Note: Unevenness of the floor possible due to hot-dip galvanizing! Ramps: Hot-dip galvanized Caution: The images are archive images!

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 2,520 kg, maximum load weight: 8,000 kg, overall weight: 10,500 kg, axle configuration: 2 axles, loading space length: 5,500 mm, loading space width: 2,050 mm, loading space height: 400 mm, total length: 7,280 mm, total width: 2,550 mm, total height: 2,900 mm, suspension: steel, tire size: 235/75 R17,5", tire condition: 100 %, Custom-made transport solution Configure your Fliegl vehicle according to your requirements. The vehicle shown is an example. Production and equipment are customized according to customer requirements. Chassis: Central axle trailer, low loader Fine-grained steel welded construction Gear-supported front support Telescopic rear support 2 chock blocks with holder Fenders made of sheet steel over both wheels with anti-splash flaps only on the last axle Aluminum side impact protection Front crossbar that can be inserted into the floor holes Coupling device for central axle trailer Drawbar with tested 40 mm towing eye Drawbar height-adjustable via spindle, max. adjustment range 250 mm Axles + Suspension BPW drum brake axles "Axle/chassis laser-aligned" – reduces tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearing and mechanical axle load compensation (linkage compensation) Wheels and tires 235 / 75 R 17.5" as per manufacturer's choice Steel rims, factory silver Braking system 2-line compressed air braking system Spring-loaded parking brake 2 fail-safe coupling heads at the front, with connecting lines to the towing vehicle Parking sockets for electrical wiring, ABS/EBS and air connection to the drawbar 24 Volt EBS, Electronic Braking System with EBS plug at the front, with connecting cable Isdpfezcnugox Ah Rsic Caution: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! "TPMS" tire pressure monitoring system according to ECE R 141, display via display in the towing vehicle, via EBS Electrical system 24 Volt, multi-chamber lights in LED, yellow LED lighting on the side, license plate lighting in LED Yellow LED lighting on the side coupled with the turn signal "flashing side lights" 2 white position lights at the front in LED 2 white/red outline lights at the rear in LED Premium LED side marker lights, with "20 LED diodes per light" 2 x 7-pole fail-safe plugs at the front, with connecting cable Platform TTS low-lying steel tub, platform floor made of steel/non-slip metal plate, steel walls firmly welded to the floor Platform length 5500 mm Tub with "Load-Lock profile" at the front and on the side for attaching lashing straps (8 pieces at the front, 16 pieces on each side) 2 pairs of lashing rings, 1 x at the front in the corners of the steel tub and 1 x at the rear in the floor, each 5 tons 3 pairs of additional lashing rings in the floor, each 5 tons 4 pairs of lashing rings screwed onto the side walls Ramps Steel ramps, 2,300 mm long, 510 mm wide, can be shifted sideways with handrail on the ramps covered with wood (tip area with steel/non-slip metal plate) with gas spring for single-person operation Rear wall / rear corner posts Screen-printed panel, 400 mm high, pluggable, between ramps Operating instructions The specified total weight is technically possible, depending on the load, the total weight may not be reached while complying with the permissible axle/support and saddle loads. Country of registration / signs Country of registration: Germany Type approval according to EG 2007/46 prepared for license plate holder, single-line Contour marking with reflective strips according to ECE R 048, white on the side and red at the rear Warning sign according to ECE - 70 Custom-made transport solution

Condition: used, machine/vehicle number: WFDFLT33902030001, empty load weight: 6,075 kg, overall weight: 35,000 kg, axle configuration: 3 axles, first registration: 05/2023, total length: 13,850 mm, total width: 2,550 mm, total height: 3,940 mm, suspension: air, tire size: 435/50 R19,5", Please note: The images shown are archive images. The vehicle may still be in use. "Preload" – slight preload in the neck area, drawbar coupling with a replaceable 2" kingpin, outer frame slightly angled, new design with "Load-Lock profile" for securing lashing straps, 24 tons, 2-speed landing gear, single-sided operation. Door lock on the side, support wedges with holder, aluminum side impact protection, galvanized steel under-ride protection, quarter-panel fenders in front of the 1st axle and behind each axle, with anti-splash flaps behind each axle, rear impact protection, pallet stops on both sides, approx. 15-20 mm high, in bolted design, loading height reduced by approx. 15-20 mm, plastic tool box with drawer and insert, b=650 / h=520 / d=670 mm. Axles + Suspension SAF disc brake axles, "axle/chassis laser-measured" – reduces tire wear and fuel consumption, air suspension, 1st axle is an automatic lift axle, including forced lowering and start-up assistance, axle lift below the recommended driving height. Iedpfx Aezcmmzoh Rsic Braking system 2-line compressed air braking system, spring-loaded parking brake. 2 fail-safe coupling heads at the front, without connection line, EBS, electronic braking system with EBS socket at the front, without connection cable. Note: with lift and lower valve, ride height in connection with lift axle, when the lift axle is raised, the loading or overall height increases by 50 mm. Wheels and Tires 435/50 R19.5", steel rims. Electrical System 24 Volt, multi-chamber lights, 2 white position lights at the front, 2 white/red marker lights at the rear, 2 x 7-pole and 1 x 15-pole fail-safe sockets at the front, without connection cable. Floor Sieve-printed panels, approx. 30 mm thick, on longitudinal supports for high point loads, for forklift axle load up to a maximum of 7100 kg. Front Wall / Front Corner Posts 2580 mm high, corner posts made of steel in a box-section design, release mechanism for side tarpaulin on the front wall. Intermediate Posts 3 pairs of sliding posts that can be moved along the entire length, with 4-fold insertion pockets and a long pocket at the bottom. 3 pairs of post positions Insertion strips 5 rows of aluminum insertion strips + Vario strips. Rear Wall / Rear Corner Posts Rear corner posts made of steel up to the lower edge of the roof, attachment for tarpaulin with round tube and tarpaulin tensioning ratchet. Tarpaulin Tarpaulin with welded-in horizontal and vertical straps, tensioning closures made of stainless steel. Roof Fliegl-Blitz sliding tarpaulin, rear end lift that can be folded up, with tarpaulin that can be slid from back to front, L-shaped roof beam for the automotive industry, internal width between the roof beams approx. 2490 mm, tarpaulin color: white (in connection with the sliding tarpaulin, without running carriage at the front). Country of Approval / Plates Germany, type approval according to EC 2007/46, 24/7 service hotline, Fliegl manufacturer's certificate for body strength according to EN 12642 XL, Fliegl manufacturer's certificate for body strength according to DL 9.5, pallet stops on both sides, approx. 20 mm high, loading height reduced by approx. 20 mm, Fliegl manufacturer's certificate for load securing according to VDI 2700 Sheet 12 ff., pallet stops on both sides, approx. 20 mm high, loading height reduced by approx. 20 mm, prepared for license plate holder, single row, warning sign according to ECE - 70, reflective strips: white, continuously on the lower part of the

Condition: used, axle configuration: 2 axles, loading space length: 62,000 mm, loading space width: 24,900 mm, loading space height: 3,800 mm, Year of construction: 2020, Equipment: ABS, = Additional Options and Accessories = - Air suspension, rear - Air suspension, front = Notes = For inquiries regarding the vehicle, please contact Mr. Seidel (at the following telephone number). Fliegl TPS 119 flatbed trailer Air suspension, 40 mm drawbar coupling, Duomatic, GFA axles, Knorr ABS, spring brake, loading ramps, permissible total weight: 11,900 kg, unladen weight: 3,250 kg, payload: 8,650 kg, cargo area dimensions: L 6,200 mm W 2,490 mm H 380 mm, tire tread: 1st axle 10 mm, 2nd axle 10 mm Upon request, we will provide you with a leasing or financing offer. Mr. Seidel (tel. ) will be happy to assist you. Iisdpfx Aey Ada Toh Rsc Further information can be found on our website. ... Errors, changes and prior sale reserved!!! - = Further Information = Unladen weight: 3,250 kg Payload: 8,650 kg GVW: 11,900 kg Last inspection: 2026-07 Please contact Tobias Ebert for further information.

Condition: used, maximum load weight: 2,300 kg, overall weight: 3,000 kg, axle configuration: 2 axles, first registration: 06/2015, Ref. No.: B - 06 On behalf of customer Fliegl * TTS 30-30 * Low-bed trailer * Ramps * 2-axle * Permissible total weight 3000kg * Very good condition, little used Trade-in possible Financing starting at 3.99% Errors and prior sale excepted! Iiedoxvf U Nopfx Ah Rsc The information in this advertisement is non-binding descriptions and does not constitute guaranteed characteristics. The seller assumes no liability for typographical or data transmission errors. Stated features should be checked separately. All details in the ads are non-binding! Nationwide delivery within Germany available upon request. Opening hours: Monday to Thursday from 9:00 am to 5:00 pm Friday from 9:00 am to 2:00 pm and by appointment!

Condition: used, overall weight: 18,000 kg, first registration: 09/2019, loading space length: 7,000 mm, loading space width: 2,480 mm, loading space height: 3,000 mm, - Twin tyres - Mega, - 3 m internal height - side loading Iijdpfsxxxltjx Ah Rjc

Condition: used, maximum load weight: 30,200 kg, overall weight: 35,000 kg, axle configuration: 3 axles, first registration: 03/2019, next inspection (TÜV): 06/2025, loading space length: 7,200 mm, loading space width: 2,420 mm, loading space height: 1,750 mm, loading space volume: 30 m³, total width: 2,550 mm, total height: 3,380 mm, Equipment: ABS, Fliegl DHKA 390 SDS01 30m³ Rear Tipper Aluminum Body Light 3-axle rear tipping semi-trailer with lightweight aluminum body, Type DHKA 390 – 30 m³ with attached rear tailgate, Greenline----### Aluminum Body Light / Aluminum Box Body ###---- Aluminum tipping body, Capacity: approx. 30 m³, Fifth wheel height: approx. 1,200 mm, Gross vehicle weight rating (GVWR): 35,000 kg, Unladen weight: 4,800 kg, Payload: 30,200 kg, 1st axle liftable, Roll tarp, foldable to the front-right side, with central locking to the front-left, 2x LED work lights at rear, SAF axles, Steel standing platform with anti-slip grate and safety railing, Hard-chromed tipping cylinder, Rear underrun protection, foldable, 1x drop-down support leg, Disc brakes, Broom and shovel holder mounted on front wall, Air suspension, Pendulum tailgate, mechanically locked (2-hook locking), Pendulum tailgate/rear wall sealed with rubber gasket, Side wall locking with screw fasteners, 1x grain slide, 1x side storage compartment on the left, 1x front storage compartment, Mudguards on all wheels, Loading platform dimensions (LxWxH): approx. 7,200 x 2,420 x 1,750 mm, Side wall height: approx. 1,750 mm, Loading height: approx. 3,239 mm, External dimensions (LxWxH): approx. 8,600 x 2,550 x 3,340 mm, Wheelbase: 3,100 x 1,310 x 1,320 mm, Tyres: 385/65R 22.5 on aluminum rims, Tread depth tyres left front: 14 mm, Tread depth tyres left center: 14 mm, Tread depth tyres left rear: 4 mm, Tread depth tyres right front: 12 mm, Tread depth tyres right center: 15 mm, Tread depth tyres right rear: 12 mm, Tipping floor worn Additional equipment: Overall length: approx. 8,600 mm, Overall width: approx. 2,550 mm, Overall height: approx. 3,340 mm, Internal body height: approx. 1,750 mm, Capacity: approx. 30 m³, Fifth wheel height: approx. 1,200 mm, Frame neck height: approx. 190 mm, King pin mounting dimension: approx. 600 mm, Central telescopic support, Uncoupling when loaded not possible; when uncoupled, the vehicle must be positioned sloping rearward, Rear underrun protection, foldable, Half-shell mudguards, Tarp pole with holder, Aluminium ladder approx. 3,550 mm with side holder, SAF disc brake axles, Air suspension, 1st axle automatic lift axle, additionally electrically operated from the truck, with start-off aid, truck installation not necessary (start-off aid functional up to axle overload of 30% and max. speed of 25 km/h), Spring-loaded parking brake, Iedpfxswr Ry Eo Ah Rsic EBS, Electronic Braking System with EBS socket at front, without connection cable, Note: The trailer may only be towed by tractors that ensure the effectiveness of the ABS! 24 volt, 4x 3-chamber rear lights + 1 round reverse light + 1 round rear fog light, all LED, 2 white position lights at front, 1x 15-pin socket at front, without connection cable, Low-pressure cylinder max. 170 bar, with HDK screw coupling, fixed, NW 48 mm, Hard-chromed tipping cylinder, Bodies: Aluminum box body made from high-quality, wear-resistant material, Sloped front wall, 5 mm thick, With external cylinder mount, Side walls of 30 mm hollow chamber profiles, precisely welded, With bulk material deflecting upper rail profile, Greenline – conical, aerodynamic body shape, 'membrane' rear wall, Rear wall as pendulum tailgate, externally mounted with double hook locking, Rear wall with additional clamping bolts at the sides and bottom, Rear wall with rubber gasket, Note: Heat-resistant up to max. 170°C!, Central grain chute, Continuous floor 6 mm t

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 3,100 kg, maximum load weight: 34,900 kg, overall weight: 38,000 kg, axle configuration: 3 axles, total length: 7,690 mm, total width: 2,550 mm, suspension: air, tire size: 385/65 R22,5", tire condition: 100 %, Customized Transport Solution Configure your Fliegl vehicle according to your requirements. The vehicle shown is an example. Production and equipment are carried out individually according to customer requirements. Chassis, Saddle, Container Fine-grained steel welded construction, saddle plate with 2 interchangeable kingpins Container receptacles: 1 x 20 ft in the center (or swap body container 7.15 / 7.45), not retractable at the front, the pivot pins of the container locking mechanism in the longer version 24 tons, 2-stage support jacks, single-sided operation with anti-splash flaps according to EC Front axle drip tray with 1 1/4 inch drain pipe + 1 1/4 inch shut-off valve, incl. drip tray, with perforated tread plates, approx. 400 mm wide, left + right between the drip tray and the longitudinal beam 4 hose racks, approx. 4500 mm long, for hose pipes 2 x DN 200 on the outside + 2 x DN 160 arranged in the center, hose box (stainless steel) at the rear, 300 mm deep, splash-proof, lid (stainless steel) all around with rubber seal, with drain hole at the lowest point, then without lid on the hose pipes Iodpfxji Rixkj Ah Rsic 1 stainless steel grounding lug at the rear on the right on the frame, with international grounding sticker on the frame Climbing steps at the rear right on the underrun protection, at the rear on the right outside on the main beam, tread plate approx. 260 mm long and 300 mm wide Axles + Suspension SAF disc brake axles Axle/chassis laser-measured to reduce tire wear and fuel consumption Offset axle spacing (combined transport) up to 44 tons total weight Air suspension 1st axle automatic lift axle, including forced lowering and starting aid, actuation 3x brakes Braking system 2-line pneumatic braking system Color-coded line routing for easy maintenance Spring-loaded parking brake 2 fail-safe coupling heads at the front, without connecting line EBS, Electronic Braking System with EBS socket at the front, without connecting cable Note: The trailer may only be pulled by tractor units that guarantee the effectiveness of the ABS! with lifting and lowering valve Vehicle - Driving Stability System Axle load detection via EBS-CAN bus signal, for display on the screen in the driver's cab, truck must be prepared accordingly, no truck installation (no calibrated scale) Wheels and Tires 385/65 R22.5, manufacturer's choice Steel rims, factory silver Electrical System 24 Volt, multi-chamber lights, yellow LED lighting on the side 2 white position lights at the front 2 white/red side marker lights at the rear 1 x 15-pole socket at the front, without connecting cable Operating Instructions The specified total weight is technically possible; depending on the cargo, the total weight may not be reached while complying with the permissible axle/support and saddle loads. (Poor driving and handling behavior possible due to incorrect load distribution) This vehicle may only be loaded with 20' tank containers that comply with ISO 668 and in particular ISO 1496-3! The tank containers must have "end-load-transfer areas" ("end-crossmember-load-transfer areas")! Country of Approval/Signs Germany Type approval according to EC 2007/46 24/7 service hotline prepared for single-line license plate holder Warning sign according to ECE - 70 Acceptance according to ADR according to 9.1.1.2 of the ADR, EX/II, EX/III / Registration certificate for vehicles for the transport of certain dangerous goods (ex.B3) with warning sign on the rear, not valid for substances according to UN

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 3,480 kg, maximum load weight: 34,520 kg, overall weight: 38,000 kg, axle configuration: 3 axles, total length: 7,450 mm, total width: 2,550 mm, suspension: air, tire size: 385/65 R22,5", Customized Transport Solution Configure your Fliegl vehicle to meet your specific requirements. The vehicle shown is an example. Production and equipment are customized according to customer specifications. Semi-Trailer Container Chassis Fine-grained steel welded construction, semi-trailer plate with replaceable 2 kingpins and 2 kingpin positions Front locking mechanism on tipper ram mounting block with guide wedges on both sides, rear locking mechanism on continuous rotary shaft with spring return Without subframe for self-supporting containers Container mounts: Locking cross members, double-mounted for securing 1 x 20-foot container (Note: low fifth-wheel load for 20-foot containers) 24 metric tons, 2-speed support jack, single-sided operation, with straight lower section, without thrust compensation Clear support foot corner dimension or clear rear swing radius approx. 1850 mm 2 wheel chocks with holders Half-shell fenders with anti-spray flaps per EC standards Hydraulics Low-pressure cylinder, max. 170 bar, smallest stage hard-chromed, with HDK Screw coupling, fixed part, nominal diameter 48 mm. (without hose connection) Hydraulic operation via truck auxiliary power unit Hydraulic connection with hose and HDK screw plug, nominal diameter = 48 mm, with knurled nut Axles + Suspension 3 SAF disc brake axles with 430 mm disc diameter Laser-measured axles/chassis to reduce tire wear and fuel consumption Offset wheelbase mm (combined transport) up to 44to Iedpfei Ri Euex Ah Roic Gross train weight Air suspension. Brake System 2-line compressed air brake system Color-coded lines for easy servicing. Spring-loaded parking brake 2 non-reversible coupling heads at the front, without connecting line EBS, Electronic Brake System with EBS socket at the front, without connecting cable Caution: The trailer may only be towed by tractor units that ensure the effectiveness of the ABS! With lift & lower valve Vehicle stability control system Axle load detection via EBS CAN bus signal, for display in the cab; the truck must be equipped accordingly; no truck installation required (no calibrated scale) Wheels and Tires 6 385/65 R22.5 (manufacturer’s choice) 6 steel rims, factory silver Electrical System 24 volts, multi-chamber lights, yellow LED side lighting 2 white front position lights 2 white/red rear lane-keeping lights 2 x 7-pin reverse-proof sockets in front, without connecting cables Country of Registration/License Plates Germany With DEKRA approval and inspection report (in accordance with §13 EG - FGV) 24/7 Service Hotline Prepared for single-line license plate holder Contour markings with reflective strips per ECE R 048, white on the sides and red at the rear Paint finish Frame: colour of choice 10-year warranty against rust-through Support feet: Black coated Note: Archive images!