Used Faymonville Platform Semitrailers for sale (207)

Condition: new, overall weight: 49,500 kg, empty load weight: 10,350 kg, maximum load weight: 39,150 kg, axle configuration: 3 axles, loading space length: 9,300 mm, loading space width: 2,540 mm, loading space height: 860 mm, suspension: air/air, color: grey, tire size: 235/75 R 17,5, Equipment: ABS, Gooseneck: -Gooseneck with rear bevel of approx. 750 mm x 10° -3 pairs of lashing rings (LC 5,000 daN) -Hardwood decking 30 mm thick Loading area: -telescopic loading area with rear slope approx. 1,000 mm x 8° -1 pair of fixed wheel recesses in front of the axles approx. 2,850 x 970 x 400 mm -Wheel recesses with square climbing strips 15 x 15 mm and widenings in the lower area -A pair of fixed wheel recesses between the 1st and 2nd axles, approx. 1,610 x 970 x 400 mm -3-piece removable galvanized covers over the wheel recesses (W 670 mm) - max. point load 5 to / pc. -Recess in the chamfer and protruding into the loading area to accommodate the excavator dipper stick approx. 2,900 x 750 x 210/290 mm -1 pair of lashing rings lying in the front of the loading area (LC 10,000 daN) -5 pairs of lashing rings foldable outwards (LC 5,000 daN) -2 pairs of lashing rings can be folded outwards (LC 10,000 daN) -2 pairs of lashing rings in the excavator trough (LC 5,000 daN) Cut-outs in the outer frame of the cargo bed for attaching lashing straps (LC 2,000 daN) One-piece ALU ramps: -One pair of one-piece ALU ramps approx. 2,500 x 600 mm -Ramp with spring lifting mechanism and manually adjustable -Maximum load per pair: 24,000 kg Axles and tires: -BPW axles and suspension, 2 axles rigid, 1 axle self-steering -Technical axle load: 12,000 kg -Electromagnetic reverse lock via reverse gear and can be activated manually -Air suspension with lifting and lowering valve -axle tool -235/75 R 17.5 tires -TPMS tire pressure monitoring system in accordance with ECE R 141 Cgjlin T Aoiu Er Aowet Accessories included: -One spare wheel with holder in front of the bulkhead -2" kingpin -One galvanized steel bulkhead approx. 400 mm high -Yellow-red air couplings on the galvanized connection strip at the front -4 wheel chocks with holder on the bulkhead -Mounting in the rear area of the gooseneck for ALU docking lights -Galvanized extensions, extendable by approx. 230 mm per side -Galvanized folding supports under the bevel of the cargo bed -One bracket for a rotating beacon at the rear of the trailer -White reflector tape in accordance with EU regulations on the sides, on the pull-out and red at the rear -One bracket for the warning signs including socket on the left and right of the gooseneck and on the rear panel -ALU drop sides and rear wall can be plugged onto the gooseneck approx. 2,440 x 400 mm -The rear galvanized stanchions are removable (length of the body approx. 2,560 mm) -2 pairs of WADER container pockets in the loading area for a 20ft or 30ft container -3 pairs of stanchion pockets for 100 x 50 mm stanchions in the outer frame of the cargo bed -One removable galvanized intermediate table with 1 pair of WADER container pockets -Square climbing rails 20 x 20 mm every 200 mm on the outer frame of the loading area slope -a layer of sand painted onto the chequer plates on the gooseneck and on the loading area to prevent slipping -Four warning signs approx. 423 x 423 mm, extendable by approx. 400 mm, with a position light -A bracket for a rotating beacon on the warning signs -Speed sticker 80 km/h at the rear and on both sides -Load manometer for determining the axle loads including load diagram -HRM metallization (High Resistance Metallization) of the outer frame -Complete steel construction shot-blasted, then the defined visible surfaces hot-finished in metallization with ZINACOR 850 (zinc 85% - aluminium 15%)

Condition: new, overall weight: 49,500 kg, empty load weight: 11,000 kg, maximum load weight: 38,500 kg, axle configuration: 3 axles, loading space length: 9,300 mm, loading space width: 2,540 mm, loading space height: 860 mm, suspension: air-lift, color: grey, tire size: 235/75 R 17,5, Gooseneck: -Gooseneck with rear bevel of approx. 750 mm x 10° -3 pairs of lashing rings (LC 5,000 daN) -Hardwood decking 30 mm thick Loading area: -telescopic loading area with rear slope approx. 1,000 mm x 8° -1 pair of fixed wheel recesses in front of the axles approx. 2,850 x 970 x 400 mm -Wheel recesses with square climbing strips 15 x 15 mm and widenings in the lower area -A pair of fixed wheel recesses with cover between the 1st and 2nd axle, approx. 1,610 x 970 x 400 mm -Recess in the chamfer and protruding into the loading area to accommodate the excavator dipper stick, approx. 2,900 x 750 x 210/290 mm -1 pair of lashing rings lying in the front of the cargo bed (LC 10,000 daN) -5 pairs of lashing rings foldable outwards (LC 5,000 daN) -2 pairs of lashing rings can be folded outwards (LC 10,000 daN) Cut-outs in the outer frame of the cargo bed for attaching lashing straps. (LC 2,000 daN) -incl. 3 removable galvanized covers over the wheel recesses - max. point load 3.5 to / pc. Hydr. two-part steel ramps: -One pair of galvanized two-part steel ramps approx. 2,750 + 1,400 x 800 mm with approx. 48 mm thick hardwood decking -Ramp with hydraulically folding and unfolding ramp sections, hydraulic lifting gear and hydraulically movable Axles and tires: -PW axles and suspension, 2 axles rigid, 1 axle self-steering Cslisup U Hzjn T Awjgt -Technical axle load: 12,000 kg -Electromagnetic reverse lock via reverse gear and can be activated manually -Air suspension with lifting and lowering valve -axle tool -235/75 R 17.5 tires Accessories included: -2" kingpin -One galvanized steel bulkhead approx. 400 mm high -One spare wheel with holder in front of the bulkhead -Yellow-red air couplings on the galvanized connection strip at the front -4 wheel chocks with holder on the bulkhead -Mounting in the rear area of the gooseneck for ALU docking lights -Galvanized extensions, extendable by approx. 230 mm per side -Galvanized folding supports under the bevel of the cargo bed -One bracket for a rotating beacon at the rear of the trailer -White reflector tape in accordance with EU regulations on the sides, on the pull-out and red at the rear -One bracket for the warning signs including socket on the gooseneck and on the left and right rear plate -One mud flap at the rear of the trailer -European reflector plates (red/yellow) at the rear of the trailer -ALU drop sides and rear wall pluggable onto the gooseneck approx. 2,440 x 400 mm -The rear galvanized stanchions are removable (length of the body approx. 2,560 mm) -2 pairs of WADER container pockets in the loading area for a 20ft or 30ft container -3 pairs of stanchion pockets for 100 x 50 mm stanchions in the outer frame of the cargo bed -One removable galvanized intermediate table with 1 pair of WADER container pockets -Square climbing rails 20 x 20 mm every 200 mm on the outer frame of the loading area slope -Four warning signs approx. 423 x 423 mm, extendable by approx. 400 mm, with a position light -One bracket for rotating beacon on the warning signs -Speed sticker 80 km/h at the rear and on both sides -Load manometer for determining the axle loads including load diagram -HRM metallization (High Resistance Metallization) of the outer frame. -Complete steel construction shot-blasted, then the defined visible surfaces hot-finished in metallization with ZINACOR 850 (zinc 85% - aluminium 15%) Optionally available: -A toolbox on the gooseneck

Condition: new, overall weight: 63,000 kg, empty load weight: 15,550 kg, maximum load weight: 47,450 kg, axle configuration: 3 axles, loading space length: 8,800 mm, loading space width: 2,540 mm, loading space height: 860 mm, suspension: air, color: grey, tire size: 235/75 R 17,5, Equipment: ABS, Gooseneck: -Gooseneck in SNT design to optimize the loading area length, length approx. 3,700 mm -Rear gooseneck with bevel approx. 1,000 mm x 10° Loading area: -Loading area in extendable design, length approx. 8,800 mm, with bevel at the rear approx. 500 mm x 10° -One recess protruding into the loading surface and into the chamfer to accommodate the excavator dipper arm -Pneumatic locking with conical locking pins and reinforced locking positions -Hardwood covering on the bevel of the loading area Cslin T Aek Aht Ujwjgt Ramps: -1 Pair of two-part steel ramps with a length of approx. 4,350 mm and a width of approx. 900 mm -Ramps with hardwood decking -Hydraulically folding ramp tips -Ramps can be moved individually hydraulically by approx. 235 mm outwards and approx. 215 mm inwards -Square climbing ledges 20 x 30 mm, approx. every 200 mm on the outer frame of the ramp Axles and suspension: -BPW axles and suspension, 1st axle with preload steering, all other axles with forced hydromechanical steering -Technical axle load: 12,000 kg -1st axle with electromagnetic reverse lock via reverse gear and can be activated manually -Air suspension with lifting and lowering valve -235/75 R 17.5 twin tires -TPMS tire monitoring system in accordance with ECE R141 -TPMS tire monitoring sensors mounted in all wheels including spare wheels Accessories included: -steel front wall, pluggable, approx. 400 mm high -3 kW electro-hydraulic unit for controlling the hydraulic processes, with the exception of hydraulic cable winches -Parking position on the gooseneck for the warning signs when not in use -1 Spare wheel -On the gooseneck 1 pair of plug-in ALU side panels, approx. 400 mm high, anodized -One plug-in ALU rear panel on the gooseneck, approx. 400 mm high, anodized -Approx. 40 mm thick hardwood covering over the gooseneck, checker plate covering over the kingpin -2" kingpin -Guide plate from the gooseneck for the saddle plate, approx. 500 mm wide -4 wheel chocks -Mechanical seat posts with 2-speed gearbox and crank -JOST module B - static test load = 50,000 kg -1 Intermediate table, approx. 300 mm wide -Widenings (galvanized) extendable by approx. 230 mm per side -Wheel recesses with square climbing rails -ALU covers for the wheel recesses -1 pair of mechanical rear supports -Steering can be operated from the front and rear by cable remote control, with tracking control of the axles -1st axle with automatic lift axle function -Central lubrication system with 1 pump, BEKAMAX brand -Radio remote control for operating the self-steering, in addition to the cable remote control, with 2 indicator lights on the receiver as toe-in control -Wabco Smart Board System -4 warning signs, approx. 423 x 423 mm, extendable by approx. 400 mm, incl. 2 position lights and brackets for rotating beacon

Condition: new, overall weight: 49,500 kg, empty load weight: 12,300 kg, maximum load weight: 37,200 kg, axle configuration: 3 axles, loading space length: 9,300 mm, loading space width: 2,480 mm, loading space height: 860 mm, suspension: air-lift, color: grey, tire size: 235/75 R17.5, Equipment: ABS, Gooseneck: -Gooseneck with rear bevel of approx. 750 mm x 10° -Hardwood covering 30 mm thick Two-piece steel ramps: -A pair of galvanized two-part steel ramps approx. 3,185x1,420x1,250 mm with grating decking -Ramp with hydraulically folding and unfolding ramp sections, hydraulic lifting gear Gooseneck: -Gooseneck with rear bevel of approx. 750 mm x 10° -3 pairs of lashing rings -Hardwood decking 30 mm thick Two-part steel ramps: -One pair of galvanized two-part steel ramps approx. 3,185x1,420x1,250 mm with grating covering -Ramp with hydraulically folding and unfolding ramp sections, hydraulic lifting gear -Maximum load per pair: 30,000 kg Loading area: -Loading surface with rear slope of approx. 1,000 mm x 8° -Hardwood flooring approx. 48 mm thick, checker plate flooring over the axles Axles and tires: -BPW axles and suspension, two axles rigid, one axle self-steering -Air suspension with lifting and lowering valve The self-steering axles with electro-magnetic reverse lock can be activated via reverse gear or manually -235/75 R17.5 3PMSF tires Accessories included: -1 Spare wheel with holder -TPMS tire pressure monitoring system according to ECE R 141 -2" kingpin -Galvanized steel bulkhead Celinstvfkfe T Awegt -Yellow-red air couplings on the galvanized front connecting strip -4 restraining shoes with holder on the bulkhead -Mounting in the rear area of the gooseneck for ALU docking ramps -3 height aluminum boards -Galvanized folding supports under the bevel of the cargo bed Height-adjustable tarpaulin superstructure (3,960 mm) -Galvanized bulkhead with a tensioning mechanism for the sliding curtain -Height-adjustable by approx. 400 mm -"EDSCHA" brand roof can be moved forwards on ALU roof rail profiles bolted to the front and rear wall -3 pairs of sliding stanchions in the loading area -The body can be hydraulically widened at the rear to the left and right by approx. 750 mm -Sliding roof with pivoting portal support -Sliding tarpaulin with 700 mm reserve in length, with tension belts at approx. 600 mm intervals -Height top edge of body approx. 3,960 mm -Driving with the sliding tarpaulin open is not permitted and will damage the tarpaulin -Cover plates to bridge the free space between ramps and loading area -Electric hydraulic unit at the rear, under the cargo bed -On the gooseneck and on the ramps on the left and right, one bracket each for the warning signs including socket -Control valves for the ramps mounted on the right-hand side of the trailer -6 pairs of stanchion pockets for 100 x 50 mm stanchions in the outer frame of the cargo bed -Lift axle on the front axle -Grating in the bevel of the loading area C40/4 (point load 3.4 tons on an area of 20 x 20 cm) -One INOX toolbox 565 x 290 x 810 mm in the direction of travel on the right between the axles -A layer of sand painted onto the chequer plates on the gooseneck and on the loading area to prevent slipping -BEKAMAX (Pico) central lubrication system with NLGI-2 standard grease and removable protection around the pump -Four warning panels approx. 423 x 423 mm, extendable by approx. 400 mm, with a position light -Load manometer for determining the axle loads including load diagram -HRM metallization (High Resistance Metallization) of the outer frame -Complete steel construction shot-blasted, then the defined visible surfaces hot-finished in metallization with ZINACOR 850 (zinc 85% - aluminium 15%)

Condition: new, overall weight: 60,800 kg, empty load weight: 13,250 kg, maximum load weight: 47,550 kg, axle configuration: > 3 axles, suspension: air, color: grey, tire size: 245/70 r17.5, Equipment: ABS, Gooseneck: Gooseneck with rear bevel of approx. 750 mm x 10°. 3 pairs of lashing rings Hardwood decking 30 mm thick Loading platform in extendable version: Loading area in extendable version with rear bevel of approx. 1,000 mm x 8° 5 pairs of lashing rings can be folded outwards 3 pairs of lashing rings can be folded outwards 1 pair of lashing rings lying in the front of the cargo bed Cut-outs in the outer frame of the cargo bed for attaching lashing straps Hardwood flooring approx. 48 mm thick, checker plate flooring over the axles Two-part steel ramps: A pair of galvanized two-part steel ramps approx. 2,750 + 1,400 x 800 mm with approx. 48 mm thick hardwood decking. Ramp with hydraulically folding and unfolding ramp sections, hydraulic lifting gear and hydraulically movable. Maximum load per pair: 40,000 kg Seat posts: JOST fifth wheels (mechanical) with 2-speed gearbox for 24t lifting load (50t test load) Axles and tires: BPW axles and suspension, 1st axle rigid, all other axles hydro-mechanically forced steered Technical axle load: 12,000 kg Air suspension with lifting and lowering valve Axle tool Tires 245/70 R 17.5 Celinsl Uxdks T Awsgt Brake system: Brake system in accordance with EU regulations with EBS-E (4S3M) without connecting lines to the tractor unit Steel construction: Steel construction made of high-strength fine-grained steels Steel grades: S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa) Coating: First-class and durable corrosion protection of the standard shot-peened welded frame guaranteed by a 2-component (2K) zinc dust primer A high-quality 2-component (2K) top coat in a single color in nova grey Rear section metallized and painted in RAL 9010 (pure white) No metallic paint finish possible Electrical system: Electrical system in accordance with EU regulations, 24 volt lighting ASPÖCK-NORDIK (ASS3) ASPÖCK-UNIBOX on the front connection strip with 24N, 24S & 15-pin sockets Connection according to ISO 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Accessories included: 2" kingpin One galvanized steel end wall approx. 400 mm high Yellow-red air couplings on the galvanized connection strip at the front 4 restraining shoes with holder on the bulkhead One spare wheel with holder in front of the bulkhead Electro-hydraulic unit Re-steering from the front and rear by means of cable remote control operated via pushbuttons with tracking control of the axles Mounting in the rear area of the gooseneck for ALU docking lights European reflector plates (red/yellow) at the rear of the trailer White reflective tape in accordance with EU regulations on the side, on the extension and at the rear Red On the gooseneck and on the ramps on the left and right, a holder for the warning signs including a socket A bracket for a rotating beacon at the rear of the trailer Galvanized folding supports under the sloping loading area Operating valves for the ramps fitted on the right-hand side of the trailer Cover plates to bridge the gap between the ramps and the cargo bed A mud flap at the rear of the trailer Manual and description on USB stick BEKAMAX (Pico) central lubrication system with NLGI-2 standard grease and removable protection around the pump ALU drop sides and rear wall can be plugged onto the gooseneck approx. 2,440 x 400 mm The rear galvanized stanchions are removable Length of the body approx. 2,560 mm One tool box INOX 1,350 x 400 x 400 on the gooseneck Box covered oil filler plug 4 pairs of WADER container pockets in t

Condition: new, overall weight: 50,000 kg, maximum load weight: 38,100 kg, axle configuration: > 3 axles, loading space length: 13,100 mm, loading space width: 2,480 mm, loading space height: 760 mm, suspension: air-lift, color: grey, tire size: 205/65 R17.5 3PMSF, Equipment: ABS, Gooseneck: Gooseneck with rear bevel of approx. 750 mm x 10° 3 pairs of lashing rings Hardwood decking 30 mm thick Loading area: 5 pairs of lashing rings can be folded outwards 3 pairs of lashing rings can be folded outwards 1 pair of lashing rings lying in the front of the cargo bed Cut-outs in the outer frame of the cargo bed for attaching lashing straps Hardwood flooring approx. 48 mm thick, checker plate flooring over the axles Seat posts: JOST seat posts with 2-speed gearbox for 24 t lifting capacity Axles and tires: BPW axles, two axles rigid two axles self-steering, air-sprung, with drum brake, with raise/lower function The self-steering axles with electromagnetic reverse lock can be activated via reverse gear or manually Axle tool Tires 205/65 R17.5 3PMSF Brake system: WABCO brake system in accordance with EU regulations with EBS-E Steel construction: Steel construction made from high-strength fine-grained steels Steel grades: Cslin T Aetphtmewsgt S355J2+N/S355MC S690QL/S700MC Electrical equipment: Electrical system in accordance with EU regulations, 24 volt lighting ASPÖCK-NORDIK ASPÖCK-UNIBOX on the front connection strip with 24N, 24S & 15-pin sockets Connection according to ISO Paintwork: First-class and durable corrosion protection of the standard shot-peened welded frame guaranteed by a 2-component zinc dust primer A high-quality 2-component Top coat single color in MB 7350 nova grey No metallic paint finish possible Rear section metallized and painted in RAL 9010 Accessories included: 1 spare wheel 205/65 R 17.5 TPMS tire pressure monitoring system in accordance with ECE R 141 Yellow-red air couplings on the galvanized connection strip at the front 4 brake shoes with holder on the bulkhead Mounting in the rear area of the gooseneck for ALU docking lights Galvanized folding supports under the bevel of the cargo bed A holder for a rotating beacon at the rear of the trailer Height-adjustable tarpaulin body Galvanized bulkhead with a tensioning mechanism for the sliding curtains Height-adjustable by approx. 400 mm "EDSCHA" brand roof can be moved forwards on ALU roof rail profiles bolted to the front and rear wall 3 pairs of sliding stanchions in the loading area The body can be hydraulically widened at the rear to the left and right by approx. 750 mm Sliding roof with pivoting portal support Sliding tarpaulin with 700 mm reserve in length, with tension belts at approx. 600 mm intervals Height top edge of body approx. 3,960 mm Driving with the sliding tarpaulin open is not permitted and will damage the tarpaulin Suspension strip for ALU docking lights at the rear of the vehicle A holder for the warning signs including socket on the gooseneck and on the rear panel on the left and right respectively A mud flap at the rear of the trailer European reflector plates at the rear of the trailer 7 pairs of stanchion pockets for 100 x 50 mm stanchions in the outer frame of the cargo bed Lift axle on the front axle with control by TEBS E depending on the current axle load and the current load condition Rear body closed with ALU hinged doors A layer of sand painted onto the chequer plates on the gooseneck and on the cargo bed to prevent slipping BEKAMAX central lubrication system with NLGI-2 standard grease and removable protection around the pump Speed sticker 80 km/h at the rear and on both sides Load manometer to determine the axle loads including load diagram

Condition: new, overall weight: 68,000 kg, empty load weight: 15,900 kg, maximum load weight: 63,500 kg, operation weight: 52,100 kg, axle configuration: > 3 axles, loading space length: 12,700 mm, loading space width: 2,740 mm, loading space height: 860 mm, suspension: air, color: grey, tire size: 235/75/r17,5, Equipment: ABS, Gooseneck: Gooseneck in SNT design to optimize the loading area length, length approx. 3,300 mm, rear with bevel approx. 1,000 mm x 10° Technical fifth-wheel load: 23,000 kg For SZM: 6x2, 6x4 and 8x4 Cargo bed: Loading area in extendable design, length approx. 9,400 mm with bevel at the rear approx. 500 mm x 10° A recess in the loading area and protruding into the chamfer to accommodate the excavator dipper stick approx. 3,850 x 950 x 210/290 mm Pneumatic locking with conical locking bolt and reinforced locking positions, the supply lines are protected in the extendable beams and automatically adjust to the respective loading area length Axles and tires: BPW axles and suspension, 1st axle rigid, all other axles hydro-mechanically forced steered Technical axle load: 12,000 kg Air suspension with lifting and lowering valve Axle tool 235/75 R 17.5 3PMSF dual tires Load index 143/141J (144/144F) Two-piece steel ramps: A pair of two-piece steel ramps with a length of approx. 4,350 mm and a width of approx. 900 mm Hardwood decking Hydraulically hinged ramp tips Ramps can be moved individually hydraulically by approx. 235 mm outwards and approx. 215 mm inwards Brake system: WABCO EBS-E brake system in accordance with EU regulations Sockets and lighting: 24-volt lighting system Full metallization: Complete HRM metallization with ZINACOR 850 to ensure the best corrosion protection Surface treatment: Complete steel structure automatically blasted after welding with wheel blast cleaning Second blasting with corundum for optimum adhesion of the coating system Final coating with 2 layers of 2-component paint in a single color in nova grey, followed by sealing of the cavities with special wax Rims in silver gray Steel construction: Steel construction made from high-strength fine-grain steels Steel grades: S355J2+N/S355MC S690QL/S700MC Accessories: Steel end wall, pluggable, approx. 400 mm high Connection strip for supply lines to the SZM Spiral cable for supplying the electro-hydraulic unit and/or the electric cable winch between the trailer and SZM with plug Electro-hydraulic unit for controlling the hydraulic processes, with the exception of hydraulic cable winches Outer beam of the gooseneck with fastening holes for screwable lashing rings The first hole approx. 200 mm from the front, then approx. every 400 mm One fastening hole in the rear upper area of the gooseneck outer beam for a screwable lashing ring Approx. 40 mm thick hardwood covering over the gooseneck, checker plate covering over the kingpin Guide plate from the gooseneck for the fifth wheel plate, approx. 500 mm wide Continuous, approx. 50 mm thick hardwood planking on the loading area, interrupted between the axles Locking of the cargo bed with conically welded locking profiles every 250 mm, including pretensioning plate Slotted holes for attachable and movable bridging elements: on the fixed part behind the gooseneck on the front of the cargo bed Cgolomfqi Ioin T Awot 1 movable intermediate table, for the large cross-section extension tube Control valves for the hydraulic ramps on the right-hand side of the vehicle Central lubrication system with 1 pump, with standard grease according to NLGI-2 Radio remote control for operating the steering, in addition to the cable remote control, with 2 indicator lights on the receiver as single-track control