Used Faymonville Platform Semitrailers for sale (187)

Condition: new, maximum load weight: 25,300 kg, overall weight: 38,000 kg, axle configuration: 2 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory, including vehicles available immediately or at short notice, on our website. Excerpt from the equipment details. Full specifications available upon request. Neck (Gooseneck) * Gooseneck in SNT design to optimize loading platform length * Approx. 3,750 mm long, hydraulically liftable/lowerable and detachable * Technical fifth wheel load: 25,000 kg For tractors: 4x2 and 6x2 Kessel Bridge (Tiefbett section) * Low bed designed as extendable Kessel bridge in SUPER LOW design * Approx. 6,850 mm length * With mechanical locking * Service lines routed protected inside the extendable beams, automatically adjusting to match the low bed’s length Rear Chassis * Short version with closed outer frame and checker plate cover * Chassis with excavator trough, closed at the rear half to accommodate air tanks Axles * BPW axles and suspension, all axles hydro-mechanically forced steered * Technical axle load: 12,000 kg per axle * Air suspension with lifting and lowering valve Tires * GOODYEAR KMAX T 3PMSF (M+S) 245/70 R 17.5 twin tires. Load index 143/141J (146/146F) Brake system * Brand: WABCO, EBS-E according to EU regulations, without connection cable to the tractor unit Paintwork * 6-Coat final treatment * All-steel construction shot-blasted after welding * 1 layer of zinc-based primer * 1 layer of adhesion primer. Final coating with 2 coats of 2-component acrylic paint in a single color, followed by cavity sealing with special wax Trailer color * RAL 3002 Carmine Red * Rim color: Silver grey * Drop side color: Natural aluminum Accessories included Ppodpfev Sw E Ajx Alqer * Removable steel front wall, approx. 400 mm high * 3 kW electro-hydraulic unit for hydraulic operations (except for hydraulic winches). Without supply connection installed on tractor unit * Spare wheel carrier in front of the gooseneck front wall * Side beams of the gooseneck with fixing holes for bolted lashing rings; first hole approx. 200 mm from the front, then at approx. every 400 mm * 2 pairs of screw-in lashing rings included (LC 5,000 daN) * 1 lashing ring each left and right on the rear taper of the gooseneck (LC 6,000 daN) * 2" king pin * Hydraulic cross member for supporting the gooseneck on the tractor unit or a dolly * Air connection with air gun at the gooseneck * 1 pair of steel ramps with climbing strips and securing pins to bridge the mountings of the low bed * 1 lashing ring each left and right on the front cross member (LC 10,000 daN) * Outer side beams of the loading area prepared for removable loading floor * Lashing rings with retaining spring at approx. every 1,200–1,300 mm on the inside carrier’s exterior of the loading area * Lashing rings with retaining spring at approx. every 1,200–1,300 mm on the outer carrier’s exterior of the loading area (LC 10,000 daN) * Cut-outs above the lashing rings in the outer carrier’s upper flange * Mechanical pin-tab coupling from low bed to rear chassis, for swapping the loading floor or installing extension beams, with electro-pneumatic-hydraulic couplings * The outer carriers of the low bed coated with anti-slip sand finish for slip resistance * 2nd ride height for high ride position, max. ± 50 mm from normal ride position, without installation of controls from the tractor unit * 1 pair lashing rings with retaining spring at the transition from the low bed to the excavator trough (LC 10,000 daN) * Front and rear tapers

Condition: new, maximum load weight: 91,640 kg, overall weight: 126,000 kg, axle configuration: > 3 axles, total width: 2,850 mm, Equipment: ABS, You can find our complete vehicle inventory, including immediately and short-term available vehicles, on our website. Excerpt from the equipment features. Full specification available upon request. Gooseneck * Hydraulically liftable/lowerable and detachable gooseneck. Length approx. 3,650 mm. Suitable for tractor units: 6 x 4 or 8 x 4 3-Axle Compact Front Bogie * Hook couplings front and rear, length: approx. 3,560 mm * Chassis width: approx. 2,850 mm Excavator Deck * Telescopic excavator deck BB-A with drive-over deck hooks at the front and a bolt coupling at the rear * Base width: approx. 2,850 mm, Length: approx. 7,150 mm, Main beam height: approx. 430 mm, Main beam width: approx. 1,350 mm * Loading height approx. 580 mm with ground clearance approx. 150 mm 5-Axle Rear Bogie * Mechanical bolt coupling for front connection of a low-bed, rear end traverse * Chassis width: approx. 2,850 mm * Chassis length: approx. 6,840 mm * 3-axle pendulum axle Front Bogie * PENDULUM AXLE, all axles hydro-mechanically forced-steered * Hose rupture valve on axle compensation cylinder with automatic RESET function * Hydraulic cylinders with shut-off valves and stopper pins for securing in raised position * Axles finished with 2 layers of MB7350 Novagrau single-colour 2-component paint * Technical axle load: 14,640 kg per axle (62 km/h) * Hydraulic axle compensation * Front bogie tyres: 12 x Manufacturer’s choice (M+S) 285/70 R19.5, load index 150/148J, pendulum axle 5-Axle Rear Bogie * PENDULUM AXLE, all axles hydro-mechanically forced-steered * Hose rupture valve on axle compensation cylinder with automatic RESET function * Hydraulic cylinders with shut-off valves and stopper pins for securing in raised position Pedpfxjuvbdte Alqjpr * Axles finished with 2 layers of MB7350 Novagrau single-colour 2-component paint * Technical axle load: 14,640 kg per axle (62 km/h) * Hydraulic axle compensation * Rear bogie tyres: 20 x Manufacturer’s choice (M+S) 285/70 R19.5, load index 150/148J Paintwork * HRM metallization of the entire vehicle chassis using ZINACOR 850 (85% zinc/15% aluminium) to ensure the best possible corrosion protection * Final coat with two layers of 2K topcoat, single-colour in RAL 3002 Carmine Red, according to the RAL System 841GL. Rims in silver grey Incl. Accessories * Steel front wall, approx. 400 mm high * Detachable ALU side walls and rear wall approx. 400 mm high in anodized finish, mountable on the gooseneck * 3.5" kingpin * BEKA-MAX central lubrication system for one gooseneck * Multi-coupling hydraulic connections on the gooseneck * BEKA-MAX central lubrication system for one 3-axle bogie * One 7-pin socket left and right rear on the front bogie for warning signs * Screw-in option (ø approx. 40 mm) every approx. 500 mm on the outside of the upper flange of the external tube of the excavator deck for lashing rings (LC 16,000 daN) * Folding extensions with steel mattress, width adjustable from approx. 2,850 mm to approx. 3,250 mm * Steel mattresses can be positioned in 2 ways to achieve a lowered loading platform. Load capacity depends on extension, refer to the respective load chart * Steel mattresses with rubber flooring approx. 12 mm thick * One 7-pin socket left and right, front and rear of the rear bogie for warning signs * BEKA-MAX central lubrication system for one 5-axle bogie * Socket on the rear bogie for cable remote control of rear steering * Rear bogie with trough * Two INOX toolboxes, approx. 855 x 340 x 390 mm, mounted on the goos

Condition: new, maximum load weight: 50,400 kg, overall weight: 65,000 kg, axle configuration: > 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory, including units available immediately and at short notice, on our website. Excerpt from the equipment list. Full equipment specifications available on request. GOOSENECK * Gooseneck in SNT design to optimize loading platform length, approx. 3,700 mm long, with rear bevel approx. 1,000 mm x 10° * For tractor units: 4 x 2, 6 x 2, and 6 x 4 * Removable steel front wall, approx. 400 mm high * ASPÖCK-UNIBOX on the front connector strip with sockets * 3 kW electro-hydraulic unit for controlling hydraulic operations, excluding hydraulic winches * 1 pair of removable aluminum side boards, approx. 400 mm high, anodized finish * 1 removable aluminum tailgate, approx. 400 mm high, anodized finish * Approx. 40 mm thick hardwood floor above gooseneck, checker plate floor above king pin * 2-inch king pin * Rear section of gooseneck prepared for aluminum drive-on ramps * Round NATO socket on the front connection strip (Maeler & Kaege VG 96 917) LOADING PLATFORM * Extendable loading platform, approx. 8,800 mm long, with rear bevel approx. 500 mm x 10° * Recess in the loading platform and bevel for accommodating excavator dipper stick approx. 3,850 x 750 x 210/290 mm (L x W x H) * TPMS tire pressure monitoring system per ECE R 141 * BPW axles and suspension, 1st axle steerable, all remaining axles hydro-mechanically forced steered * 1st axle with electromagnetic reverse lockout, activated via reverse gear and manually * Technical axle load: 12,000 kg each, air suspension with raise and lower valve * Tires: 235/75 R 17.5, twin tires, 3PMSF * Mechanical landing legs with 2-speed gearbox and crank, JOST Module B – static test load approx. 50,000 kg * Continuous 50 mm thick hardwood floor on the loading platform and interrupted between axles (increases coefficient of friction) * 1 intermediate table, approx. 300 mm wide, for the extension tube with large cross-section Pjdpfxstx Nwnj Alqepr * Extendable (galvanized) side extensions, approx. 230 mm per side (without wooden planks) * Wheel recesses with square climbing strips, approx. 15 x 15 mm ahead of axles, open through to gooseneck cross member, approx. 700 x 410 mm (W x D) * Aluminum covers for wheel recesses, usable as bridging elements for extension OR as widening planks * Aluminum elements lockable on telescopic tubes of the extensions * Widenable U-profiles for inserting ALU covers: - on the fixed section behind the gooseneck - on the intermediate table - on the extendable platform * Wheel recesses with square climbing strips, approx. 15 x 15 mm between 1st and 2nd axle, approx. 1,480 x 700 x 410 mm (L x W x D) * Aluminum covers for the wheel recesses, usable as bridging elements for the extension OR as widening planks * Aluminum elements lockable on the extension’s telescopic tubes * 1 pair of mechanical rear supports * Remote steering from front and rear via cable remote control, with axle tracking, without installation in the tractor unit HYDRAULIC LOADING RAMPS * One pair of two-section steel ramps, Type: DR-15/60-900-4350-KG-HV-M, approx. 4,350 mm in length and approx. 900 mm wide each * Hydraulically foldable ramp tips * Ramps can be shifted hydraulically approx. 235 mm outward and approx. 215 mm inward individually * Super Grip rubber surface approx. 25 mm and steel plate surface approx. 5 mm as additional

Condition: new, maximum load weight: 38,140 kg, overall weight: 48,000 kg, axle configuration: 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory, including vehicles available immediately and at short notice, on our website. Excerpt from equipment. Full equipment details available on request. Gooseneck: - Gooseneck with front corners chamfered approx. 45° and rear bevel approx. 750 mm x 10° - 3 pairs of lashing rings (LC 5,000 daN) - Hardwood flooring, approx. 30 mm thick Loading area: - Telescopic loading area with rear incline approx. 1,000 mm x 8° - Between 1st and 2nd axle: one pair of fixed wheel recesses, approx. 1,610 x 970 x 400 mm (L x W x D) - Incl. 3-piece removable galvanized cover over wheel recesses (width approx. 670 mm – max. point load 5 t / pc.) - 1 pair of flat lashing rings at the front of the loading area (LC 10,000 daN) - 4 pairs of outward folding lashing rings (LC 5,000 daN) - 3 pairs of outward folding lashing rings (LC 10,000 daN) - Cutouts in the outer frame for attaching tie-down straps (LC 2,000 daN) Landing legs: - JOST landing legs (manual) with 2-speed gearbox for 24 t lifting capacity (50 t test load) Psdow Tpq Djpfx Alqspr Tyres: - Tyres 235/75 R17.5 3PMSF, make at our discretion - TPMS tyre pressure monitoring system in accordance with ECE R 141 - Data transfer to the towing vehicle via standardised EBS interface as per ISO 11992 - For correct display, the towing vehicle must be able to receive and display this data Axles: - BPW axles and suspension, 2 axles rigid, 3rd axle self-steering - Technical axle load: 12,000 kg - Electromagnetic reverse lockout activated automatically when reversing and manually - Air suspension with lifting and lowering valve. Axle tools Braking system: - WABCO braking system according to EU regulations with EBS-E (2S2M) without piping to the tractor unit Electrical system: - Electrical system per EU regulations - LED lighting 24 Volt ASPÖCK-NORDIK (ASS3) - All LED side marker lights flash with the indicator - ASPÖCK-UNIBOX at front connection strip with 24N, 24S & 15-pin sockets, according to ISO; 24N ISO-1185, 24S ISO-3731, 15-pin ISO-12098 Steel construction: - Steel structure made of high-strength fine-grained steels - Steel qualities: S355J2+N/S355MC (yield strength 355 MPa), S690QL/S700MC (yield strength 690 MPa) Paintwork: - Complete steel structure automatically shot-blasted after welding in a wheel-blasting system - Second shot-blasting with corundum for optimum coating adhesion - HRM metallization of entire chassis with ZINACOR 850 (85% zinc/15% aluminium) for maximum corrosion protection - Final painting with 2 layers of 2K topcoat, single-colour in RAL 3002 Carmine Red, rear section metallized and painted in RAL 9010 Pure White - Metallic finish not available - Paint structure tested in salt spray test according to ISO 9227-NSS - Internal cavities sealed with special wax Including the following accessories: - On the gooseneck and rear, left and right, one holder for warning signs each, including socket - Spare wheel holder in front of the front wall (without spare wheel) - 2-inch king pin - Galvanized steel front wall, approx. 400 mm high - Yellow-red air couplings on the galvanized front connection bar - Galvanized folding supports under the inclination at the rear of the loading area - A hardwood crash protection strip at the rear wall from gooseneck to the loading area - 1 pair of recessed lashing rings along the central beam at the rear inclination (LC 10,000 daN) - Aluminium drop sides and tailgate on the gooseneck

Condition: new, maximum load weight: 25,645 kg, overall weight: 38,000 kg, axle configuration: 2 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete stock of immediately and soon-to-be available vehicles on our website. Excerpt from equipment specification. Complete specification available on request. Load area: - Low-bed design with central beam, extendable version, approx. 6,750 mm in length - 5 pairs of fold-out external lashing rings (LC 5,000 daN) - 1 pair of fold-out external lashing rings (LC 10,000 daN) - 1 pair of flat-mounted lashing rings at the rear of the loading platform (LC 10,000 daN) Gooseneck: - Hydraulic lifting/lowering gooseneck, detachable Rear chassis: - Short rear chassis with closed outer frame and checker plate covering - Chassis with excavator trough, closed in the rear half for housing the air tanks - 2 pairs of fold-out external lashing rings (LC 5,000 daN) - 1 pair of fold-out external lashing rings (LC 10,000 daN) - 1 pair of flat-mounted lashing rings at the rear of the chassis (LC 10,000 daN) Axles: - BPW axles, hydro-mechanically forced steering - Air suspension with raise/lower control valve Tyres: - Tyres 245/70 R 17.5, 3PMSF - TPMS: Tyre Pressure Monitoring System according to ECE R 141 Brake system: - Wabco braking system in accordance with EU regulations with EBS-E (2S2M) Paintwork: - High-quality single-tone 2-component (2K) top coat in RAL 3000 Flame Red Including the following additional equipment: - 2 kingpins - Galvanised steel front wall, approx. 400 mm high - Remote steering from front and rear, operated by cable remote control with push buttons, including single tracking control for the axles (no installation in the tractor unit) - Electro-hydraulic unit - Axle load gauge including load diagram - On the gooseneck, removable aluminium side walls and rear wall, approx. 2,440 x 400 mm (L x H). Rear galvanised stake pockets are removable. (Body length approx. 2,560 mm) - Separate air connection with air gun on the gooseneck - 2 work lights with switch on the trailer, mounted on the left and right of the gooseneck platform - 1 INOX toolbox, approx. 1,350 x 400 x 400 mm, on the gooseneck - 6 pairs of stake pockets for insertable posts approx. 100 x 50 mm in the outer frame of the load area, 2 pairs in the chassis outer frame - Galvanised, extendable width extensions approx. 230 mm per side - Hydraulic connections from gooseneck to low bed with multi-coupling (instead of screw couplings). No seal guarantee included. - Central lubrication system with 2 BEKAMAX (Pico) pumps, standard NLGI-2 grease, with removable protection around the pump - 2 pairs of WADER container locks on the loading area, for 1x20' container - 1 removable galvanised intermediate table with 1 pair of WADER container locks - 1 pair of steel ramps for bridging the low bed’s hook mountings - Anti-slip sand-coated layer painted on the load area - HRM Metallisation (High Resistance Metallisation) Pedpfjxf Silsx Alqepr

Condition: used, maximum load weight: 51,870 kg, overall weight: 65,000 kg, axle configuration: > 3 axles, first registration: 03/2025, next inspection (TÜV): 03/2026, total width: 2,540 mm, Equipment: ABS, You can find our entire vehicle inventory, including immediately and short-term available vehicles, on our website. Excerpt from the equipment list. Complete equipment details available upon request. GOOSENECK * Gooseneck in SNT design to optimize loading platform length, length approx. 3,700 mm, rear with chamfer approx. 1,000 mm x 10° * For tractors: 4 x 2, 6 x 2, and 6 x 4 * Plug-in steel front wall, approx. 400 mm high * At the front connection strip: yellow-red air couplings * ASPÖCK-UNIBOX on the front connection strip with 24N, 24S & 15-pin sockets * 3 kW electro-hydraulic power unit for hydraulic operations * External beams of the gooseneck with mounting holes for bolted lashing rings * One mounting hole at the rear upper part of the gooseneck external beam for a bolted lashing ring * 1 pair of screw-in lashing rings included (LC 10,000 daN) * On the gooseneck, 1 pair of plug-in side aluminum drop sides, approx. 400 mm high, anodized version * On the gooseneck, 1 plug-in aluminum rear wall, approx. 400 mm high, anodized version * Approx. 40 mm thick hardwood flooring above the gooseneck * 2-inch kingpin * Gooseneck guide plate for fifth wheel, approx. 500 mm wide * Rear gooseneck mounting for aluminum ramps * Round NATO socket at the front connection strip (Maeler & Kaege VG 96 917) LOADING PLATFORM * Loading platform, extendable version, length approx. 8,800 mm, rear with chamfer approx. 500 mm x 10° * Recess in the platform and chamfer for accommodating the excavator dipper stick approx. 2,490 x 750 x 210/290 mm (L x W x H) Ppsdpfxsxtc Uhe Alqor * TPMS tire pressure monitoring system in accordance with ECE R 141 * BPW axles and suspension * 1st and 2nd axle fixed, 3rd and 4th axles steering trailing axles * 3rd and 4th axles with electro-magnetic reverse lock, activated via reverse gear and manually * Technical axle load: 12,000 kg each * Air suspension with raise and lower valve * 235/75 R 17.5 3PMSF twin tires * Mechanical landing legs with 2-speed gearbox and crank, JOST Module B – static test load approx. 50,000 kg * Complete platform and interrupted between the axles with approx. 50 mm thick hardwood flooring (increasing the coefficient of friction) * Platform locking with conically welded locking profiles every approx. 250 mm * Elongated slots for insertable and repositionable bridging elements at the front of the platform * Intermediate table with set-down platform, approx. 300 mm wide, for large cross-section telescopic tube with sheet metal covering – front and rear with elongated slots for insertable and repositionable bridging elements – removable cover flush with the platform * 1 pair of lashing rings on the front cross member (LC 10,000 daN) * 6 pairs of flush-mounted lashing rings in the outside frame of the platform, foldable outward (LC 10,000 daN) * Additionally, 1 pair of lashing rings externally on the front cross member of the platform, approx. 90° turned inward towards the platform (LC 10,000 daN) * Extendable galvanized widening extensions by approx. 230 mm per side * 1 pair of permanently installed wheel recesses, open up to the extension, approx. 700 x 410 mm (W x D), sheet-covered in the platform ahead of the 1st axle, wheel recesses with square climbing strips approx. 15 x 15 mm, spaced approx. 200 mm * Between the 2nd and 3rd axles, 1 pair of permanently installed wheel recesses on the platform, approx. 1,695 x 700 x 410 mm (L x W x D), covers for wheel recesses split lengthwise, with wooden overlay, outer plug-in loc

Condition: new, maximum load weight: 37,680 kg, overall weight: 50,960 kg, axle configuration: > 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete inventory of vehicles, including those available for immediate and short-term delivery, on our website. Extract from the equipment features. Complete specification available on request. Gooseneck * With approximately 30 mm thick hardwood flooring. Gooseneck with straight rear section * 3 pairs of lashing rings (LC 5,000 daN) Loading Area * Extendable design * 5 pairs of outward-folding lashing rings (LC 5,000 daN) * 3 pairs of outward-folding lashing rings (LC 10,000 daN) * 1 pair of recessed lashing rings at the front of the loading area (LC 10,000 daN) * Cutouts in the outer frame of the loading area for attaching tension straps (LC 2,000 daN) * Approx. 48 mm thick hardwood flooring, treadplate covering above the axles Landing Gear * JOST mechanical landing gear with 2-speed gearbox, lifting capacity approx. 24 t (test load approx. 50 t) Tyres * 205/65 R 17.5 Axles * BPW axles and suspension * 1st axle fixed, all other axles hydro-mechanically forced-steered * Air suspension with lift and lower valve Brake System * In accordance with EU regulations, with EBS-E (4S3M) without connection lines to the tractor unit Steel Construction * Made of high-strength fine-grained steels * Steel grades: S355J2+N/S355MC (yield strength 355 MPa), S690QL/S700MC (yield strength 690 MPa) Paintwork * Premium and durable corrosion protection for the standard shot-blasted welded frame, guaranteed by a two-component (2K) zinc dust primer * High-quality two-component (2K) top coat, single colour RAL 3002 carmine red Ppsdpfx Aev Etx Eelqsr * Rims in silver Accessories Included * 2" king pin * Galvanised steel front wall, approx. 400 mm high * Yellow-red air couplings on galvanised front connection strip * 4 chocks with holder on the front wall * Spare wheel holder in front of the front wall * Electro-hydraulic unit * Steering from the front and rear via cable remote control with push buttons, including single-track control of the axles (without installation in the tractor unit) * European reflective signs (red-yellow) at the rear of the trailer * Yellow reflective tape according to EU regulations on sides, extensions, and rear of the trailer * Bracket for warning signs including socket, left and right on the gooseneck and rear plate * Bracket for rotating beacon at the rear of the trailer * Galvanised foldable support legs under the loading area's chamfer * Load gauge for determining axle loads including load diagram * 7 pairs of WADER container pockets for: 1x 20' or 1x 40' container on the loading area, 1x 40' container over the gooseneck, or 2x 20' containers * Support block with 1 pair of WADER container pockets, fifth wheel load approx. 20,000 kg * 7 pairs of stake pockets for approx. 100 x 50 mm plug-in stakes in the outer frame of the loading area * Galvanised, extendable width extensions, approx. 230 mm per side * Sliding hook-in rails for aluminium loading ramps at the rear of the vehicle * 1 pair of recessed lashing rings along the central beam at the rear of the loading area (LC 10,000 daN) * 2 pairs of ferry rings under the gooseneck and 2 pairs at the rear * BEKAMAX (Pico) central lubrication system with standard grease NLGI-2 and removable pump protection * 2 LED reversing lights mounted at the rear * Acoustic reversing warning signal * HRM Metallisation (High Resistance Metallisation)

Condition: new, maximum load weight: 33,865 kg, overall weight: 48,000 kg, axle configuration: 3 axles, Equipment: ABS, You can find our complete range of vehicles, including those available for immediate delivery or on short notice, on our website. Below is an excerpt from the specification. The full equipment list is available upon request. Gooseneck: * Gooseneck with front corners chamfered approx. 45° and a rear bevel approx. 750 mm x 10° * 3 pairs of lashing rings (LC 5,000 daN) * Hardwood flooring approx. 30 mm thick Load area: * Double extendable design with rear bevel approx. 500 mm x 8° * 6 pairs of folding external lashing rings (LC 5,000 daN) * 4 pairs of folding external lashing rings (LC 10,000 daN) * 1 pair of recessed lashing rings at the front of the loading area (LC 10,000 daN) * 1 intermediate table approx. 250 mm * Hardwood flooring approx. 48 mm thick, over axles with checker plate covering * Cut-outs in the external frame of the loading platform for attaching tie-down straps (LC 2,000 daN) Axles: * BPW axles and suspension, all axles forced-steered hydro-mechanically * Design axle load: 12,000 kg each * Air suspension with lift and lower valve * Axle tools included Tyres: * 245/70 R 17.5, load index (146/146 F) * Brand of our choice Landing legs: * JOST mechanical landing legs with 2-speed gearbox for approx. 24 t lifting capacity (approx. 50 t test load) Braking system: * Braking system according to EU regulations with EBS-E (2S2M) without connection lines to the tractor unit Paintwork: First-class and durable corrosion protection * High-quality, one-colour 2-component (2K) topcoat in RAL 3002 carmine red * Rear section metallized and coated in RAL 9010 (pure white) Steel Structure: Steel construction from high-strength fine grain steels. * Steel grades: S355J2+N/S355MC (yield strength 355 MPa), S690QL/S700MC (yield strength 690 MPa) Electrical system: * Electrical system according to EU regulations * 24 Volt lighting ASPÖCK-NORDIK (ASS3) * ASPÖCK-UNIBOX at the front connection strip with 24N, 24S & 15-pin sockets, compliant with ISO. 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Including the following additional equipment: * 2-inch kingpin * Galvanized steel front wall, approx. 400 mm high * Yellow-red air couplings at the galvanized front connection strip * Spare wheel carrier in front of the front wall * Electro-hydraulic unit * Rear and front steering via cable remote control with push-buttons, with single-track monitoring of the axles (without installation in the tractor unit) * Mount at the rear of the gooseneck for aluminum loading ramps * Removable aluminum ramp hanging rail at the rear of the vehicle * Galvanized folding supports beneath the slope of the load area * On the gooseneck: plug-in aluminum side boards and rear board, approx. 2,440 x 400 mm (L x H) * The rear galvanized stanchions are removable (body length approx. 2,560 mm) * One galvanized toolbox, integrated in the chamfered gooseneck * 4 pairs of WADER container pockets in the loading area for one 20', two 20', one 40' or one 45' container * 8 pairs of stanchion pockets (approx. 100 x 50 mm) in the external frame of the loading platform * Galvanized extensions, extendable by approx. 230 mm per side * Adjustable hanging rails for aluminum ramps at the rear of the vehicle * 2 pairs of ferry rings under the gooseneck and 2 pairs at the rear Ppjdpfxew Tprzo Alqer * Central lubrication system with 2 BEKAMAX (Pico) pumps, filled with standard grease NLGI-2 and removable pump guard * 2 LED reversing lights mounted on the rear panel * HRM Metallization (High Resistance Metallisa

Condition: new, maximum load weight: 39,720 kg, overall weight: 50,960 kg, axle configuration: > 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory, including immediately and short-term available vehicles, on our website. Sample equipment features. Full specification upon request. Gooseneck * With beveled front corners approx. 45° and rear bevel approx. 750 mm x 10° * 3 pairs of lashing rings (LC 5,000 daN) * Hardwood flooring, approx. 30 mm thick Loading Platform Loading platform in extendable design * 5 pairs of fold-out outer lashing rings (LC 5,000 daN) * 3 pairs of fold-out outer lashing rings (LC 10,000 daN) * 1 pair of recessed lashing rings at the front of the loading platform (LC 10,000 daN) * Recesses in the outer frame of the loading platform for securing straps (LC 2,000 daN) * Hardwood flooring approx. 48 mm thick, over axles with chequer plate covering Landing Gear * JOST (mechanical) with 2-speed gearbox, approx. 24 t lift capacity (approx. 50 t test load) Axles * BPW axles: 2 fixed axles, 2 steering axles, drum brakes * Air suspension with lift/lower function * Self-steering axle with electro-magnetic reverse lock, activated via reverse gear or manually * Tires: 205/65 R 17.5 Psdpfx Aju Sd U Uslqopr Brake System * Wabco brake system in accordance with EU directives with EBS-E (4S3M), without interconnecting lines to the tractor unit Steel Construction * Made of high-strength fine-grained steels * Steel grades: S355J2+N/S355MC (yield strength 355MPa), S690QL/S700MC (yield strength 690MPa) Paintwork * First-class, durable corrosion protection of the standard shot-blasted welded frame, guaranteed by a 2-component (2K) zinc dust primer * High-quality 2-component (2K) top coat, single-color, RAL 3002 Carmine Red * Rear section metallized and painted in RAL 9010 (Pure White) * Rims in silver Accessories Included * 2-inch king pin * Galvanized front steel bulkhead approx. 400 mm high * Spare wheel holder in front of bulkhead * Yellow-red air couplings on galvanized connector bar front * 4 wheel chocks with holder at bulkhead * Bracket at rear of gooseneck for aluminum loading ramps * Galvanized folding supports under inclined edge of loading platform * Holder for beacon at rear of trailer * Yellow reflective tape on sides, extension, and rear in accordance with EU regulations * Brackets for warning signs with socket on both sides at the gooseneck and rear panel * TPMS tire pressure monitoring system per ECE R 141. Data transmission to the tractor unit via standardized EBS interface according to ISO 11992; for correct display, the tractor unit must support data transmission and display * Plug-in aluminum side walls and tailgate on gooseneck, approx. 2,440 x 400 mm (L x H); rear galvanized stakes are removable (body length approx. 2,560 mm) * Galvanized toolbox, integrated in gooseneck slope * 6 pairs of WADER container locks in loading platform, for 1 x 20' container, 2 x 20' containers or 1 x 40' container * Sliding mounting rails for aluminum ramps at rear of vehicle * 7 pairs of stake pockets for plug-in stakes approx. 100 x 50 mm, in the outer frame of the loading platform * Galvanized cross bracket under the loading platform * Galvanized extendable widenings, extendable approx. 230 mm per side * Lift axle on front axle, controlled via TEBS E according to current axle load and load status * 5 pairs of recessed lashing rings along the central beam (LC 5,000 daN)

Condition: new, empty load weight: 12,300 kg, maximum load weight: 37,200 kg, overall weight: 49,500 kg, axle configuration: 3 axles, loading space length: 9,300 mm, loading space width: 2,480 mm, loading space height: 860 mm, suspension: air, tire size: 235/75 R17.5, color: grey, Equipment: ABS, Gooseneck: -Gooseneck with rear bevel of approx. 750 mm x 10° -Hardwood covering 30 mm thick Two-piece steel ramps: -A pair of galvanized two-part steel ramps approx. 3,185x1,420x1,250 mm with grating decking -Ramp with hydraulically folding and unfolding ramp sections, hydraulic lifting gear Gooseneck: -Gooseneck with rear bevel of approx. 750 mm x 10° -3 pairs of lashing rings -Hardwood decking 30 mm thick Two-part steel ramps: -One pair of galvanized two-part steel ramps approx. 3,185x1,420x1,250 mm with grating covering -Ramp with hydraulically folding and unfolding ramp sections, hydraulic lifting gear -Maximum load per pair: 30,000 kg Loading area: -Loading surface with rear slope of approx. 1,000 mm x 8° -Hardwood flooring approx. 48 mm thick, checker plate flooring over the axles Axles and tires: -BPW axles and suspension, two axles rigid, one axle self-steering -Air suspension with lifting and lowering valve The self-steering axles with electro-magnetic reverse lock can be activated via reverse gear or manually -235/75 R17.5 3PMSF tires Podpfxotvfkfs Alqspr Accessories included: -1 Spare wheel with holder -TPMS tire pressure monitoring system according to ECE R 141 -2" kingpin -Galvanized steel bulkhead -Yellow-red air couplings on the galvanized front connecting strip -4 restraining shoes with holder on the bulkhead -Mounting in the rear area of the gooseneck for ALU docking ramps -3 height aluminum boards -Galvanized folding supports under the bevel of the cargo bed Height-adjustable tarpaulin superstructure (3,960 mm) -Galvanized bulkhead with a tensioning mechanism for the sliding curtain -Height-adjustable by approx. 400 mm -"EDSCHA" brand roof can be moved forwards on ALU roof rail profiles bolted to the front and rear wall -3 pairs of sliding stanchions in the loading area -The body can be hydraulically widened at the rear to the left and right by approx. 750 mm -Sliding roof with pivoting portal support -Sliding tarpaulin with 700 mm reserve in length, with tension belts at approx. 600 mm intervals -Height top edge of body approx. 3,960 mm -Driving with the sliding tarpaulin open is not permitted and will damage the tarpaulin -Cover plates to bridge the free space between ramps and loading area -Electric hydraulic unit at the rear, under the cargo bed -On the gooseneck and on the ramps on the left and right, one bracket each for the warning signs including socket -Control valves for the ramps mounted on the right-hand side of the trailer -6 pairs of stanchion pockets for 100 x 50 mm stanchions in the outer frame of the cargo bed -Lift axle on the front axle -Grating in the bevel of the loading area C40/4 (point load 3.4 tons on an area of 20 x 20 cm) -One INOX toolbox 565 x 290 x 810 mm in the direction of travel on the right between the axles -A layer of sand painted onto the chequer plates on the gooseneck and on the loading area to prevent slipping -BEKAMAX (Pico) central lubrication system with NLGI-2 standard grease and removable protection around the pump -Four warning panels approx. 423 x 423 mm, extendable by approx. 400 mm, with a position light -Load manometer for determining the axle loads including load diagram -HRM metallization (High Resistance Metallization) of the outer frame -Complete steel construction shot-blasted, then the defined visible surfaces hot-finished in metallization with ZINACOR 850 (zinc 85% - aluminium 15%)

Condition: ready for operation (used), machine/vehicle number: YAFTL40900001004, maximum load weight: 80,000 kg, overall weight: 105,000 kg, tire size: 70%, wheelbase: 1,360 mm, color: red, Year of construction: 2009, Equipment: ABS, Country of manufacture: Netherlands Body options : Disc brakes, Central lubrication system, Moving floor, Forced steering, Full side opening More information Low loader Pipe carrier, extendable, hydraulic suspension, laterally expandable up to 3500 mm interior and 4200 mm exterior, latest generation pendulum axles Podovtygfepfx Alqjpr Option to incorporate 2-axis dolly to make 2 +4 pipe carrier equipment Load 85 tons We have 2 identical equipment in perfect condition.

Condition: used, maximum load weight: 65,350 kg, overall weight: 78,000 kg, axle configuration: > 3 axles, first registration: 05/2020, With air suspension, hydraulic dual-circuit forced steering (turntable) - "Platform" crane ballast design - Corners at right angles, closed external frame - Front linkage integrated into the frame - Fifth wheel plate with ball bearing slewing ring, replaceable 3.5" king pin and adjustable steering wedge - Fifth wheel load: 28,000 kg - Maximum steering angle: 2,700 mm Ppsdpfx Alsx I U Eqeqer Chassis - 5-axle chassis with air suspension including lift and lower valve - Axles: SAF brand - Tires: 445/65 R 22.5 Brake system - Two-line all-wheel compressed air brake system with diaphragm brake cylinders - Automatic load-dependent brake (ALB) - Automatic slack adjusters (AGS) - Parking brake via spring-loaded cylinders - Anti-lock braking system (ABS) - 1st and 2nd axles liftable (in direction of travel) Technical data Cargo area (LxW): approx. 12,500 x 2,550 mm Coupling dimension B: 11,550 mm Loading height loaded (chassis area): approx. 1,490 mm at a loaded fifth wheel height: 1,200 mm Steering 1st axle: forced-steered 2nd axle: rigid 3rd - 5th axle: hydromechanical forced steering (dual-circuit steering) Radio remote control Electric power pack