Used Work Platform Trailers for sale (99)

Condition: used, maximum load weight: 7,200 kg, overall weight: 9,000 kg, axle configuration: 1 axle, first registration: 03/2008, ? Platform for ballast weights ? 40 mm towing eye ? 9 lashing eyes ? Drum brake ? Leaf spring suspension ? Support legs Isdpfxowfku Aj Afheal ? BPW axles All information is subject to change without notice. Subject to prior sale.

Condition: new, maximum load weight: 30,500 kg, overall weight: 40,000 kg, axle configuration: > 3 axles, Year of construction: 2026, * T4 RM 40.0: * Wabco EBS-E (electronic braking system) * Emergency release device for spring-loaded cylinders * Tire pressure monitoring with display capability in the truck via EBS signal – no installation required on the truck side * Drum brakes * 4 x 11 t Gigant axles * Air suspension with manual lowering at the rear * Warning panel packages front & rear * SmartBord infotool installed with pressure sensors to display total axle load per axle group * Reflective contour tape on the sides and rear * LED rotating beacon (removable) at the rear * 15-pin electrical connector * LED rear lights * Straight drawbar with 50 mm towing eye and infinitely adjustable height * Closed single plastic mudguards at the front * Straight steel mudflap skirts at the rear, each with spray suppression (anti-spray) * Side underrun protection * Front superstructure in front of the bogie platform approx. 520 mm with 45° corners and 3 storage compartments incl. lockable folding lids (lids open to the rear) * Chassis made from high-strength fine-grain steel * Deck over bogie platform from 50 mm and in low-bed platform from 60 mm softwood * Outer planks of the ramps made from 50 mm hardwood * Load securing package comprising: 2 lashing eyes 6.4 t front left and right on the main frame of the bogie platform; on each side, front and rear, 1 pair of 13.4 t lashing rings on the outer frame; 1 pair of 10 t lashing rings per side, hinged and lowerable, loadable in all directions and recessed into the outer frame; bolted 5 t lashing rings to the outer frame of the wheel recesses (2 each at the front wheel recess, 1 each at the rear); 2 pairs of 6.4 t lashing rings at the sides in the excavator boom holder * 11 pairs of folding outriggers for 3 m total width (except for rear bevel) * Storage compartment (L = 2,470 x W = 570 x H = 250 mm) for steel widening planks mounted crossways to the loading surface in front of the first rear axle * Excavator boom holder above the rear axle to the end of the approach slope approx. 2,300 x 740 x 190 mm * 2 wheel recesses per side, approx. 640 mm wide – front 340 mm deep, rear 220 mm deep – with retractable cover (storage for covers at the front on the bogie platform) for transporting wheel loaders with a wheelbase of 3,100 – 3,640 mm Iaodpfx Ajxmpydofhsl * Mechanical drop supports at the rear * Hydraulic folding ramps with hydraulic extendable ramp tip approx. 4,650 x 720 mm * Hydraulic side ramp shift * Loading area over turntable: approx. 2,990 x 2,520 mm * Rear loading area: approx. 6,780 x 2,520 mm, loaded loading height approx. 890 mm +/- 20 mm (incl. 860 mm approach slope) * Chassis, bogie, folding outriggers, rear drop supports and drive-on ramps hot-dip galvanized * Axles, air tanks and drawbar painted in black * Tires: 235/75R17.5 * Vehicle is hot-dip galvanized * New vehicle with manufacturer's warranty * Errors and subject to prior sale * Available from week 14/2026 * Sample images

Condition: used, maximum load weight: 4,930 kg, overall weight: 6,500 kg, axle configuration: 2 axles, first registration: 03/2022, loading space length: 4,100 mm, loading space width: 1,990 mm, total width: 2,545 mm, total height: 2,850 mm, Errors and prior sale excepted! Internal number: 1457. 1083677 Iedjwtvvnepfx Afhoal ---Please refer to the pictures for equipment and condition. ---The vehicle is in unprepared (original) condition! Nationwide delivery available at extra cost. Errors and prior sale reserved. We are happy to accept your vehicle as a trade-in. Financing / leasing also possible without down payment! Do you still have questions? We are happy to advise you!

Condition: used, maximum load weight: 14,170 kg, overall weight: 18,000 kg, axle configuration: 2 axles, first registration: 02/2006, loading space length: 6,530 mm, loading space width: 2,540 mm, loading space height: 1,000 mm, total width: 2,550 mm, Gross weight: 18,000 kg Unladen weight: 3,830 kg Payload: 14,170 kg Overall length: 8,550 mm Loading length: 6,530 mm Width: total width 2,550 mm / loading width 2,540 mm Loading height: approx. 1,000 mm Further information - Hardwood floor with Omega profiles Iodpfow N A Eysx Afheal - Side walls present - Twin tires - BPW axles - Lashing rings - LED reversing lights

Condition: new, empty load weight: 705 kg, maximum load weight: 1,995 kg, overall weight: 2,700 kg, axle configuration: 2 axles, loading space length: 3,940 mm, loading space width: 1,870 mm, loading space height: 100 mm, loading space volume: 0.7 m³, color: silver, construction height: 800 mm, working width: 2,540 mm, lowerable loading platform / manual hydraulics / braked, automatic reverse, hot-dip galvanizing, * IMMEDIATELY AVAILABLE * incl. lowerable loading platform / manual hydraulics / braked Technical data: - Type: New vehicle - TÜV: New/2 years - Availability: IMMEDIATELY! - Gross vehicle weight: 2,700 kg - Unladen weight: 705 kg - Payload: 1,995 kg - Interior dimensions: 394 x 187 x 10 cm (L x W x H) - Overall exterior dimensions: 553 x 254 x 80 cm (L x W x H) - Loading sill height: 44 cm - Tyres: 195/50R13C steel rim - Brake: yes - Support wheel: yes, 45 mm with clamp - 100 km/h: at extra charge - incl. vehicle documents Vehicle documents Vehicle superstructure: - Floor: Multiplex wooden floor - Drop sides: Aluminium anodized 3-sided - Drop side height: 10cm - Chassis: Low loader lowerable, ALKO rubber spring axle - Tipping function: lowerable - Hydraulics: Hand pump - Drive-on angle: approx. 6 - Wheel stopper: without - Overrun device & brake: ALKO - Frame/chassis: Welded hot-dip galvanized steel frame - Lashing eyes: 10 pieces recessed on the side - Winch: at extra charge - Supports: Supported by rear. - Ramps: with rear drive-over point - Lighting plug: 13-pin - Approval: COC papers Standard equipment: - Multiplex wooden floor - Extremely robust - Fixed 10 mm drop sides - Insertion options at all corners, e.g. for tarpaulin frame - Very sturdy welded steel frame - Frame completely hot-dip galvanized frame completely hot-dip galvanized - many stable cross beams therefore high point load - loading area can be lowered hydraulically - mechanical safety locking of the swivel axle in driving mode - with drive-over point at the rear - additional longitudinal struts welded in throughout - storage box at the front - 10 lashing eyes inside the loading area - license plate holder at the rear, can be swivelled away for loading - ALKO overrun device and parking brake - ALKO coupling head - very stable V-drawbar REINFORCED - automatic reversing - 13-pin plug - reversing light - large reversing lights plug - reversing lights - large dimensioned safety lighting - integrated rear fog light - lighting recessed in rear frame - support wheel with central clamp - registration papers: COC papers Accessories can be retrofitted - please enquire: - 100km/h approval with wheel shock absorbers - anti-theft device - spare wheel - high tarpaulin - additional lashing eyes - reversing lights - lashing straps - and much more. New vehicle with warranty and TÜV. We are happy to offer you suitable financing !, Descriptions and pictures are protected by copyright !!! Over 800 trailers immediately available for you! We are for over 30 years Brian James / Humbaur / Hapert / Unsinn / Cheval Liberte / Koch / Debon / Stedele / TPV / Tohaco / Vezeko / Variant / Vlemmix - specialized dealer & repair - workshop - delivery Germany-wide with surcharge possible! Anhänger Zentrum BAUMANN GmbH Dinxperloer Str. 389 46399 Bocholt - Errors, omissions and prior sale excepted - Iasdeu Htfxepfx Afhol

Condition: new, maximum load weight: 2,110 kg, overall weight: 2,700 kg, axle configuration: 2 axles, loading space length: 3,050 mm, loading space width: 1,550 mm, loading space height: 200 mm, B27300/150 MACHINE TRANSPORTER TECHNICAL DATA * Trailer type B27300/150 * Total weight 2700kg * Payload 2075kg * Internal dimensions L: 305cm, W: 155cm, H: 20cm * Loading height approx. 54 cm * Floor multiplex wooden floor * Lashing points recessed in the loading floor * Side walls steel * Frame welded steel, hot-dip galvanized Ijdsthlrhepfx Afhoal * Electrics 13-pin, 12V * Tires 185R14C * Axle manufacturer AL-KO or KNOTT * Number of axles 2 * Braked axle * Support wheel as standard * Walkable steel fenders * Shovel storage * Rear supports * Loading ramps - 200 cm plus vehicle registration document/ COC certificate 39.00 ¤ All prices include VAT. Images do not have to correspond to the standard equipment, technical changes (e.g. tire sizes) are subject to change. Delivery: Delivery by freight forwarder possible, per transport kilometer ¤ 1.50 throughout Germany one way (Seesen to destination) at least 270¤ plus VAT Visit us at =.=.=.=.=.=.=.=.=.=.=.=.=.=.=.=.=.=.=.=.=.=.=.=.=.=.=.=.=.=.=. =.=.=.=.=.=. You can also get your desired trailer and accessories here by arrangement: B L Y S S transporttechnik GmbH Dieselstr. 8 85084 Reichertshofen Tel.: .:.:.:.:.:.:.:.:.:.:.:.:.:.:.:.:.:.:.:.:.:.:.:.:.:.:.:.:.:.:.:.: .:.:.:.:.:.:.:.:.:.:.:.:.:.:.: B L Y S S transporttechnik GmbH Burenkamp 18-20 46286 Dorsten - Wulfen Tel =.=.=.=.=.=.=.=.=.=.=.=.=.=.=.=.=.=.=.=.=.=.=.=.=.=.=.=.=.=.=. =.=.=.=.=.=.=. ?FINANCE OR LEASING POSSIBLE* Vehicle number (for customer inquiries) Images do not necessarily correspond to the standard equipment, technical changes (e.g. tire sizes) are subject to change.

Condition: new, maximum load weight: 10,950 kg, overall weight: 14,400 kg, axle configuration: 2 axles, loading space length: 6,270 mm, loading space width: 2,470 mm, Year of construction: 2026, * ETÜ-TA-ER 14.4 Platform: * RDÜ (Tire Pressure Monitoring System) * EBS (Electronic Braking System) * Emergency release device for spring-loaded cylinders * Drum brakes * 2 x 7 t BPW axles * Air suspension with lift and lower function * Mechanically adjustable 3-meter warning sign boards at front and rear * Drawbar height adjustable by 300 mm with 40 mm flange towing eye * Drawbar shortened by approx. 200 mm to approx. 1,800 mm (resulting in a B-dimension of approx. 8,080 mm) * Support windlass at the front * External folding supports at the rear * Plastic toolboxes approx. 750 x 350 x 300 mm, mounted left & right side * Side underrun protection * Rear underrun protection * Plastic quarter mudguards * 15-pin electrical connector * LED lighting system 12 / 24 V * 2 additional LED reversing lights at the rear (switched via reverse gear) * 1 LED beacon (removable incl. mount) at the rear * 400 mm high bolted front wall * 50 mm softwood flooring * 2 pairs of container locks (extendable to 3 m container outer width) and lockable, locking dimension retracted according to ISO - DIN 15190 = 2,259 mm. Container locks extended = 2,819 mm (this dimension is not according to DIN) with a total outer width of 3,000 mm * Perforated outer frame bent at approx. 45 degrees with 2 t lashing capacity every 480 mm, possible installation of 3 t folding lashing brackets every 600 mm; 5 x 3 t UVV-compliant lashing brackets mounted per side; at each front and rear corner 1 x 6.3 t lashing ring (front directly behind the container locks in the wooden floor and rear in the rear cross member), various holes for 1.2 t lashing options in the front and rear cross members * 1 pair of aluminum slide-in ramps approx. 3,570 x 410 mm (load capacity 10 t/pair), suitable for rubber-tyred and tracked vehicles * Rear integrated storage compartment below the loading area inside the chassis * ---Chassis, drawbar, front wall, underrun protection, and rear stabilizers hot-dip galvanized--- * Axles, air tanks, front windlass, and flange towing eye painted in a shade of black * New vehicle with manufacturer's warranty * Errors and prior sale excepted * Available from week 09/2026 Iajdpjv D Tbkjfx Afhel

Condition: used, axle configuration: 3 axles, first registration: 02/2018, loading space length: 6,060 mm, loading space width: 2,200 mm, loading space height: 300 mm, Subject to errors and prior sale! Internal number: 1448. EQUIPMENT * Platform trailer * 3 axles * Support wheel * AL-KO coupling * Planks all around ... and much more ----The vehicle is unprepared! Nationwide delivery possible for an additional charge. Iaodpfxsvwh U So Afhjl Subject to errors and prior sale. We are happy to accept your vehicle as part payment. Financing/leasing also possible without a down payment! Do you have any questions? We are happy to advise you!

Condition: new, empty load weight: 1,048 kg, maximum load weight: 2,452 kg, overall weight: 3,500 kg, axle configuration: 2 axles, loading space length: 4,550 mm, loading space width: 2,010 mm, loading space height: 300 mm, loading space volume: 2.8 m³, color: silver, construction height: 1,560 mm, working width: 2,080 mm, Hydraulics, automatic reverse drive, hot-dip galvanizing, * IMMEDIATELY AVAILABLE * TECHNICAL DATA - Make: Hapert Trailers - Model: Indigo HT-2 - Vehicle type: Construction machinery - Vehicle condition: New vehicle - Initial registration: Without initial registration - TÜV/HU: 2 years from initial registration - Internal dimensions (LxWxH): 455 x 201 x 30 cm - External dimensions (LxWxH): 618 x 208 x 156 cm - Loading height of floor: 63 cm - Perm. Total weight: 3,500 kg - Unladen weight: 1,048 kg - Payload: 2,452 kg - Chassis: High loader (wheels under the body) - Tires: 195/50R13C - Chassis: KNOTT parabolic suspension + 100 km/h - Support wheel: Yes, automatic, 800 kg - 100 km/h approval: Included! Vehicle body: - Brake: Yes - Number of axles: 2 - Floor: Full aluminum floor - Drop sides: Aluminum drop sides - Drop side height: 30 cm - Locks: Eccentric locks - Number of pallet spaces: 8 - Multifunctional vehicle: Yes - Tipping / lowering function: Tiltable - Hydraulic pump: Double-acting hydraulic pump - Overrun device/brake: KNOTT - Frame/chassis: Welded steel frame - Galvanization: Hot-dip galvanized - Drawbar: V-drawbar, continuous, square tube - Mudguards: Plastic mudguards - Spare wheel: Optional, can be retrofitted - Bucket storage: No - Superstructures / attachments: Optional, attachable - Ramp chute: No - Ramps/ramp flap: Yes - Type of ramp: Full-length tailgate - Load ramps: - - Drive-on angle: approx. 11.5 - Supports: Integrated in tailgate - Lashing eyes: 8 - Rear lighting: Incandescent lamps, lamps recessed in rear frame - Side lighting: - - Plug for lighting: 13-pin - Vehicle documents: ZBII & COC papers Standard equipment: - New dropside hinges incl. welded-on hooks for attaching a cargo net, among other things. - Aluminium drop sides with robust built-in locks - Anodized double-walled aluminium drop sides - All drop sides foldable and removable - Removable steel corner stanchions - Insertion option at all 4 corners for tarpaulin frames, lattice extension, drop side extensions or front wall extension - Sturdy eccentric locks - Hydraulically tiltable loading area (11.5 drive-up angle) - Very sturdy welded steel frame - Frame completely hot-dip galvanized - Many options for attaching tarpaulin frames, lattice extensions, drop side extensions or front wall extensions - Many options for attaching tarpaulin frames, lattice extensions, drop side extensions or front wall extensions. hot-dip galvanized - many continuous welded longitudinal beams for high point load - steel ramp standing on shaft 100cm - stable eccentric locks - support brackets on ramp - lifting aid for ramp - very low chassis for low drive-on angle - 8x lashing eyelets laterally recessed in the frame profile (1000dAN/kg) TÜV certified - parabolic spring axle from KNOTT - wheel shock absorber for 100km/h mounted - parabolic spring axle for absolute driving comfort! - Automatic reverse drive - KNOTT overrun device and parking brake - very stable bolted V-drawbar REINFORCED - 13-pin plug - reversing lights - large safety lighting - integrated rear fog light - lighting recessed in the rear frame - automatic support wheel in the middle Special equipment included in the price: - All-aluminum profile floor - Aluminum drop sides 30 cm high (front and side), instead of fixed Combi Protect Rail New vehicle with warranty and TÜV. We are happy to offer you suitable financing !, Descriptions and pictures are protected by copyright !!! Over 800 trailers immediately available Isdpfx Afsu Hrm Uehjal

Condition: new, maximum load weight: 30,740 kg, overall weight: 40,000 kg, axle configuration: > 3 axles, Year of construction: 2026, * T 4: * Wabco EBS-E (electronic brake system) * RDÜ Tire Pressure Monitoring System * Emergency release device for spring-loaded cylinders * Drum brakes * 4 x 11 t Gigant axles * Air suspension with lift and lowering function and RtR valve * Smard-Board for load weight determination * Warning sign packages front & rear * Contour tape on sides and rear, reflective * Removable rotating beacon at the rear * LED lighting * Straight drawbar with 50 mm tow eye and infinitely adjustable height * Tool box made of powder-coated steel sheet and spare wheel holder in basket design, right side * Front closed single plastic fenders * Rear straight steel mudguards with spray suppression (anti-spray) * Lateral underrun protection * Turntable platform extension by 520 mm with 45° corners and 3 integrated lockable compartments incl. lids * Chassis made of high-strength fine-grained steel * Floor over turntable platform made of 50 mm and on low-bed platform of 60 mm softwood * Outer planks of the drive-on ramps made of hardwood * Four stake pockets per side (no stakes included) with simultaneous 2 t lashing option * Load securing package consisting of: 2 lashing eyes 6.4 t at front left and right on the main frame of the turntable platform * Per side at front and rear, 2 pairs of 13.4 t lashing rings on the outer frame; per side, 4 pairs of 10 t lashing rings, swiveling and lowerable * Loadable in all directions, recessed into the outer frame * 2 pairs of 6.4 t lashing rings on the side in the excavator arm support * 8 pairs of galvanized folding outriggers for a total width of 3 m (not in the rear slope) * Widening planks stored in a compartment on the left side * Excavator arm resting area above the rear axle up to end of approach slope approx. 2,100 x 740 x 190 mm * Mechanical drop supports at rear * Hydraulic folding ramps with hydraulically adjustable ramp tip approx. 4,650 x 720 mm including hydraulic ramp side shift & load-holding valve * Loading area above turntable: approx. 2,990 x 2,520 mm * Rear loading area: approx. 6,780 x 2,520 mm * Loading height loaded: approx. 890 mm, +/- 20 mm (incl. 860 mm approach slope) Isdpfxol Tik Nj Afheal * Flow divider installed * Chassis, turntable, ramps, folding outriggers, and mechanical drop supports hot-dip galvanized * Axles, drawbar, air tanks, and turntable painted in black tone * Tires 235/75 R 17.5 * New vehicle without initial registration with manufacturer's warranty * Subject to errors and prior sale * Available from CW 07/2025

Condition: new, empty load weight: 695 kg, maximum load weight: 2,805 kg, overall weight: 3,500 kg, axle configuration: 2 axles, loading space length: 3,450 mm, loading space width: 1,620 mm, loading space height: 100 mm, loading space volume: 0.6 m³, color: silver, construction height: 700 mm, working width: 2,280 mm, Manual hydraulics, automatic reversing, hot-dip galvanizing, lowerable loading platform, braked, * IMMEDIATELY AVAILABLE * incl. lowerable loading platform / manual hydraulics / braked Technical data: - Type: New vehicle - TÜV: New/2 years - Availability: IMMEDIATELY! - Gross vehicle weight: 3,500 kg - Unladen weight: 695 kg - Payload: 2,805 kg - Interior dimensions: 345 x 162 x 10 cm (L x W x H) - Overall exterior dimensions: 500 x 228 x 70 cm (LxWxH) - Loading sill height: 44 cm - Tyres: 195/50R13C steel rim - Brake: yes - Support wheel: yes, 45 mm with clamp - 100 km/h: at extra charge - Incl. Vehicle documents Vehicle superstructure: - Floor: multiplex wooden floor - Drop sides: anodized aluminium 3-sided - Drop side height: 10cm - Chassis: low loader lowerable, ALKO rubber spring axle - Tipping function: lowerable - Hydraulics: hand pump - Drive-up angle: approx. 6 - Wheel stop: without - Overrun device & brake: ALKO - Frame/chassis: welded hot-dip galvanized steel frame - Lashing eyes: 10 pieces laterally recessed - Winch: at extra charge - Supports: supported by rear. - Ramps: with rear drive-over point - Lighting plug: 13-pin - Approval: COC papers Standard equipment: - Multiplex wooden floor - Extremely robust - Fixed 10 mm drop sides - Insertion options at all corners, e.g. for tarpaulin frame - Very sturdy welded steel frame - Frame completely hot-dip galvanized - Many options for attaching tarpaulin frame - Many options for attaching tarpaulin frame - Very sturdy welded steel frame - Many options for attaching tarpaulin frame - Many options for attaching tarpaulin frame. frame completely hot-dip galvanized - many stable cross beams therefore high point load - loading area can be lowered hydraulically - mechanical safety locking of the swivel axle in driving mode - with drive-over point at the rear - additional longitudinal struts welded in throughout - storage box at the front - 10 lashing eyes inside the loading area - license plate holder at the rear, can be swivelled away for loading - ALKO overrun device and parking brake - ALKO coupling head - very stable V-drawbar REINFORCED - automatic reversing - 13-pin plug - reversing lights - large reversing light - large rear lights - rear view mirror - large rear view mirror - large rear view mirror. plug - reversing lights - large safety lighting - integrated rear fog light - lighting recessed in rear frame - jockey wheel with central clamp - registration papers: COC papers Accessories can be retrofitted - please enquire: - 100 km/h approval with wheel shock absorbers - anti-theft device - spare wheel - high tarpaulin - additional lashing eyes - reversing lights - lashing straps - and much more. New vehicle with warranty and TÜV. We are happy to offer you suitable financing !, Descriptions and pictures are protected by copyright !!! Over 800 trailers immediately available for you! We are for over 30 years Brian James / Humbaur / Hapert / Unsinn / Cheval Liberte / Koch / Debon / Stedele / TPV / Tohaco / Vezeko / Variant / Vlemmix - specialized dealer & repair - workshop - delivery Germany-wide with surcharge possible! Anhänger Zentrum BAUMANN GmbH Dinxperloer Str. 389 46399 Bocholt - Errors, omissions and prior sale excepted - Isdpfxeu Hrkyo Afhoal

Condition: new, maximum load weight: 16,400 kg, overall weight: 30,000 kg, axle configuration: 3 axles, Year of construction: 2024, * T3 profile 30.0: * EBS-E (electronic braking system) * RDÜ tire pressure monitoring * Emergency release device for spring-loaded cylinders * Drum brakes * 3 x 11 ton BPW Eco axles * Air suspension with lifting and lowering system * SmartBoard as an information tool on the trailer with pressure sensors for pressure display for total axle load display for each axle group * Side impact protection * Mechanically adjustable warning sign packages at the front and rear * Front axle closed. Plastic fenders and rear straight galvanized sheet steel aprons, each with splash guard * Hinged lid (hot-dip galvanized) for the tool box in the bogie platform * Tool box made of galvanized sheet steel approx. 650 x 300 x 600 mm (black powder-coated) on the right side * 15-pin power plug * LED lighting 12 / 24 V * LED rotating beacon (removable) at the rear * Side marker lights with indicator control * Pull scissors with 40 mm pull eye and height adjustment via tension spring & turnbuckle * Tire pressure monitoring system with display option in the truck via EBS signal (without truck-side installation) * Rubber covering on the folding ramps and on the ramp on the left and right (approx. 860 mm long) * Rubber covering on the longitudinal beams from the front to the end beam * Hardwood floor on the running surfaces of the low-loading platform * 4 stake pockets on each side with a simultaneous 2 ton. Lashing option * La-Si package consisting of: 5 pairs of UVV lashing rings that can be swiveled and lowered, can be loaded in all directions and are embedded in the outer frame - 13.4 tons in the corners, otherwise 10 tons * 6 pairs of mechanical folding booms for 3 m total width (but not in the rear slope) * Plank holder under the loading area in the longitudinal direction * Roller stop raised in front of the front beam with 1 x 6.4 ton lashing eye on each side * Hydraulic folding ramps (approx. 4,650 x 720 mm) with hydraulically extendable tip section and load holding valves * Hydraulic lateral ramp shifting * Hydraulic rear support (single-stage cylinder) * Hydraulic. Flow divider in the trailer (with hydraulic pump output in the truck of over 40 liters up to max. 140 liters/min.) * Hydraulic control block splash-proof * Two-line hydraulics Iaedsq Dyvcopfx Afhjl * Loading area above the turntable: approx. 1,960 x 2,520 mm, * Rear loading area: approx. 6,500 x 2,520 mm (incl. 860 mm approach slope) * Loading height when loaded approx. 890 mm +/- 20 mm air suspension * Chassis, bogie, roller stop, folding extensions & ramps hot-dip galvanized. * Axles, turntable, pull scissors, air tank etc. painted in a black tone * Loading height when loaded: approx. 890mm +/- 20mm * New vehicle with manufacturer's warranty * Errors and prior sale subject to reservation * Available for immediate delivery from Egestorf

Condition: new, empty load weight: 745 kg, maximum load weight: 2,755 kg, overall weight: 3,500 kg, axle configuration: 2 axles, loading space length: 3,450 mm, loading space width: 1,620 mm, loading space height: 100 mm, loading space volume: 0.6 m³, color: silver, construction height: 700 mm, working width: 2,280 mm, lowerable loading platform / manual hydraulics / braked, automatic reverse, hot-dip galvanizing, * IMMEDIATELY AVAILABLE * incl. lowerable loading platform / manual hydraulics / braked Technical data: - Type: New vehicle - TÜV: New/2 years - Availability: IMMEDIATELY! - Gross vehicle weight: 3,500 kg - Unladen weight: 745 kg - Payload: 2,755 kg - Interior dimensions: 345 x 162 x 10 cm (L x W x H) - Overall exterior dimensions: 500 x 228 x 70 cm (LxWxH) - Loading sill height: 44 cm - Tyres: 195/50R13C steel rim - Brake: yes - Support wheel: yes, 45 mm with clamp - 100 km/h: at extra charge - Incl. Vehicle documents Vehicle superstructure: - Floor: Multiplex wooden floor - Drop sides: Aluminium anodized 3-sided - Drop side height: 10cm - Chassis: Low loader lowerable, ALKO rubber spring axle - Tipping function: lowerable - Hydraulics: Electric & emergency hand pump - Drive-on angle: approx. 6 - Wheel stop: without - Overrun device & brake: ALKO - Frame/chassis: welded hot-dip galvanized steel frame - Lashing eyes: 10 pieces recessed at the side - Winch: at extra charge - Supports: Supported by rear. - Ramps: with rear drive-over point - Lighting plug: 13-pin - Approval: COC papers Standard equipment: - Multiplex wooden floor - Extremely robust - Fixed 10 mm drop sides - Insertion options at all corners, e.g. for tarpaulin frame - Very sturdy welded steel frame - Frame completely hot-dip galvanized frame completely hot-dip galvanized - many stable cross beams therefore high point load - loading area can be lowered hydraulically - mechanical safety locking of the swivel axle in driving mode - with drive-over point at the rear - additional longitudinal struts welded in throughout - storage box at the front - 10 lashing eyes inside the loading area - license plate holder at the rear, can be swivelled away for loading - ALKO overrun device and parking brake - ALKO coupling head - very stable V-drawbar REINFORCED - automatic reversing - 13-pin plug - reversing lights - large reversing lights - large rear lights - rear view mirror - large rear view mirror - large rear view mirror. plug - reversing lights - generously dimensioned safety lighting - integrated rear fog light - lighting recessed in rear frame - jockey wheel with central clamp - registration papers: COC papers Special equipment included in the price: - Electric single-acting pump with 12V/74Ah battery - 420 mm stainless steel rear ramp Accessories can be retrofitted - please enquire: - 100 km/h approval with wheel shock absorbers - anti-theft device - spare wheel - high tarpaulin - additional lashing eyes - reversing lights - lashing straps - and much more. New vehicle with warranty and TÜV. We are happy to offer you suitable financing !, Descriptions and pictures are protected by copyright !!! Over 800 trailers immediately available for you! We are for over 30 years Brian James / Humbaur / Hapert / Unsinn / Cheval Liberte / Koch / Debon / Stedele / TPV / Tohaco / Vezeko / Variant / Vlemmix - specialized dealer & repair - workshop - delivery Germany-wide with surcharge possible! Anhänger Zentrum BAUMANN GmbH Dinxperloer Str. 389 46399 Bocholt - Errors, omissions and prior sale excepted - Iaodeu Hryuopfx Afhol

Condition: new, maximum load weight: 31,000 kg, overall weight: 40,000 kg, axle configuration: > 3 axles, loading space length: 9,290 mm, loading space width: 2,520 mm, loading space height: 950 mm, * PT 40.0 profile: * Wabco EBS-E (electronic braking system) * Emergency release device for spring-loaded cylinders * Drum brakes * 4 x 11 tonne Gigant axles * Air suspension with lifting and lowering system and RtR valve * Manometer pressure indicator for determining load weight (axles separated into 2 air suspension circuits) * Side impact protection * Swivel supports at the rear of the chassis frame * Mechanically adjustable warning sign packages at the front and rear * Front plastic quarter fender with splash guard * Rear straight galvanized. Sheet steel aprons with splash guard * Reflective contour tape on the side and rear * EBS multi-voltage system with 12 & 24 V electrics * 15-pin power plug * LED lighting system 12 / 24 V * LED rotating beacon (removable) at the rear * 2 LED reversing lights (switched via reverse gear) Ijdpol Tlhrsfx Afhsal * Pull scissors with 50 mm pull eye and height adjustment * Tool box made of galvanized sheet steel, black powder-coated, approx. 1,000 mm wide, 600 mm deep, 300 mm high * Front section in front of the bogie platform approx. 490 mm long with 45° corners * ROBOT welded ANTI-SLIP coating for the steel plate of the bogie platform * La-Si package consisting of: in front of the front wall support on the left & right 1 x 13.4 ton each. UVV lashing eye, 4 holes on each side in the bogie platform with a lashing force of 2 tons each, 1 pair of lashing eyes (13.4 tons) hanging at the rear left and right in front of the rear carrier, 4 pairs of UVV lashing rings (10 tons) on each side, can be swiveled and lowered, can be loaded in all directions and embedded in the outer frame, 3 stake pockets on each side with a simultaneous 2 ton lashing option * Hot-dip galvanized mechanical folding boom for a total width of 3 meters (but not in the rear slope) * Plank holder for widening under the chassis on the left in the longitudinal direction * Excavator boom storage above the rear axle to the end carrier approx. 2,100 mm long and approx. 190 mm deep, 2 pairs of 6.4 tons on each side. Lashing rings in the excavator boom storage * Hardwood floor on the running surfaces of the low-loading platform * Hydraulic one-piece ramps (approx. 3,000 x 720 mm) mechanically laterally adjustable * Outer planks of the ramps made of hardwood * Steel construction in preparation for 6-way control slide * Loading edge unloaded approx. 950 mm +/+ 20 mm chassis * Bogie, folding boom, mechanical drop supports, ramps hot-dip galvanized * --Axles, air tank, pull scissors painted in a black tone-- * Tires 235/75 R 17.5 * Vehicle has a daily registration in 07/2024, due to missing tire pressure monitoring system and has not been loaded/used * New vehicle with manufacturer's warranty * Errors and prior sale subject to reservation * Available for immediate delivery from Egestorf

Condition: new, empty load weight: 585 kg, maximum load weight: 2,115 kg, overall weight: 2,700 kg, axle configuration: 2 axles, loading space length: 3,450 mm, loading space width: 1,620 mm, loading space height: 100 mm, loading space volume: 0.6 m³, color: silver, construction height: 700 mm, working width: 2,280 mm, Manual hydraulics, automatic reverse drive, hot-dip galvanizing, lowerable loading platform, braked, * IMMEDIATELY AVAILABLE * incl. lowerable loading platform / manual hydraulics / braked Technical data: - Type: New vehicle - TÜV: New/2 years - Availability: IMMEDIATELY! - Gross vehicle weight: 2,700 kg - Unladen weight: 585 kg - Payload: 2,115 kg - Interior dimensions: 345 x 162 x 10 cm (L x W x H) - Overall exterior dimensions: 500 x 228 x 70 cm (LxWxH) - Loading sill height: 44 cm - Tyres: 195/50R13C steel rim - Brake: yes - Support wheel: yes, 45 mm with clamp - 100 km/h: at extra charge - Incl. Vehicle documents Vehicle superstructure: - Floor: multiplex wooden floor - Side walls: aluminium anodized 3-sided - Side wall height: 10cm - Chassis: low loader lowerable, ALKO rubber spring axle - Tipping function: lowerable - Hydraulics: hand pump - Drive-on angle: approx. 6 - Wheel stop: without - Overrun device & brake: ALKO - Frame/chassis: welded hot-dip galvanized steel frame - Lashing eyes: 10 pieces laterally recessed - Winch: at extra charge - Supports: supported by rear. - Ramps: with rear drive-over point - Lighting plug: 13-pin - Approval: COC papers Standard equipment: - Multiplex wooden floor - Extremely robust - Fixed 10 mm drop sides - Insertion options at all corners, e.g. for tarpaulin frame - Very sturdy welded steel frame - Frame completely hot-dip galvanized - Many options for attaching tarpaulin frame - Many options for attaching tarpaulin frame - Very sturdy welded steel frame - Many options for attaching tarpaulin frame - Many options for attaching tarpaulin frame. frame completely hot-dip galvanized - many stable cross beams therefore high point load - loading area can be lowered hydraulically - mechanical safety locking of the swivel axle in driving mode - with drive-over point at the rear - additional longitudinal struts welded in throughout - storage box at the front - 10 lashing eyes inside the loading area - license plate holder at the rear, can be swivelled away for loading - ALKO overrun device and parking brake - ALKO coupling head - very stable V-drawbar REINFORCED - automatic reversing - 13-pin plug - reversing lights - large reversing light - large rear lights - rear view mirror - large rear view mirror - large rear view mirror. plug - reversing lights - large dimensioned safety lighting - integrated rear fog light - lighting recessed in rear frame - support wheel with central clamp - registration papers COC papers Accessories can be retrofitted - please enquire: - 100km/h approval with wheel shock absorbers - anti-theft device - spare wheel - high tarpaulin - additional lashing eyes - reversing lights - lashing straps - and much more. New vehicle with warranty and TÜV. We are happy to offer you suitable financing !, Descriptions and pictures are protected by copyright !!! Over 800 trailers immediately available for you! We are for over 30 years Brian James / Humbaur / Hapert / Unsinn / Cheval Liberte / Koch / Debon / Stedele / TPV / Tohaco / Vezeko / Variant / Vlemmix - specialized dealer & repair - workshop - delivery Germany-wide with surcharge possible! Anhänger Zentrum BAUMANN GmbH Dinxperloer Str. 389 46399 Bocholt - Errors, omissions and prior sale excepted - Iodpfx Aou Hri Ajfhsal

Condition: new, maximum load weight: 23,500 kg, overall weight: 30,000 kg, axle configuration: 3 axles, loading space length: 8,380 mm, loading space width: 2,520 mm, Year of construction: 2024, * PT 30 profile: * EBS (electronic braking system) * Emergency release device for spring-loaded cylinders * Drum brakes * 3 x 11 tonne Gigant axles * Air suspension with lifting and lowering system and RtR valve * Smart board mounted on the trailer as an information tool (for axle load display - front and rear separately) * Tire pressure monitoring with display option in the truck via EBS signal without truck-side installation * Side impact protection * Swivel supports at the rear of the chassis frame * Mechanically adjustable warning sign packages at the front and rear * Front plastic quarter fender with splash guard * Rear straight galvanized. Sheet steel aprons with splash guard * Reflective contour tape on the side and rear * 15-pin power plug * LED lighting 12/24 V * LED rotating beacon (removable) at the rear * Pull scissors 1,200 mm long with 40 mm pull eye and height adjustment via tension spring & turnbuckle * Tool box made of galvanized sheet steel approx. 650 x 300 x 600 mm, black powder-coated on the right side * Box in the bogie for accessories with hinged lid, 2 cont. locks permanently installed (directly after the bogie platform) * ROBOT welded ANTI-SLIP coating on the steel plate of the bogie platform (protruding weld beads) * La-Si package consisting of: 2 lashing eyes (13.4 tonnes) at the front left & right on the bulkhead support, front & rear 1 pair of UVV lashing rings (13.4 to.) and 3 pairs of UVV lashing rings (10 to.) on the side, swiveling and lowerable, loadable in all directions and embedded in the outer frame, 3 stake pockets on the side with simultaneous 2 ton lashing option * 6 pairs of mechanical folding booms for 3 m total width (but not in the rear slope) * Widening planks placed in the middle of the loading area * Hydraulic one-piece loading ramps approx. 3,000 x 720 mm * Mechanically laterally adjustable * 4-way control block for later retrofitting of hydraulic. Ramp shift * Chassis, bogie, folding boom, drop supports and ramps hot-dip galvanized * Axles, slewing ring, air tank, drawbar painted in a black tone Iajdpfstplwiex Afhel * Loading edge when loaded approx. 910 mm +/- 20 mm air suspension, * New vehicle with manufacturer's warranty * Errors and interim purchase subject to reservation * Available for immediate delivery from Egestorf

Condition: new, maximum load weight: 14,550 kg, overall weight: 19,000 kg, axle configuration: 2 axles, loading space length: 6,270 mm, loading space width: 2,470 mm, loading space height: 400 mm, Year of construction: 2024, * ETÜ-TA-R 19.0: * Wabco EBS-E (electronic braking system) * RDÜ (tire pressure monitoring) * Emergency release device for spring-loaded cylinders * Drum brakes * 2 x 11 tonnes Gigant axles * Air suspension, drawbar with 50 mm flanged drawbar eye and height-adjustable drawbar * Jost landing gear at the front * External folding supports at the rear * Toolbox made of galvanized sheet steel, approx. 650 x 350 x 320 mm, on the right side (powder-coated in black) * Side impact protection * Plastic quarter fender * 15-pin power connector * LED taillights * Reinforcement package for drilling rig transport on the chassis - loading height + 20 mm * 50 mm clamped softwood floor * Device for retrofitting container locks in front of the bulkhead * Bolted bulkhead made of smooth sheet steel * Trapezoidal profiled sheet steel side walls, foldable with side wall spring jack * Steel rear wall retractable between the ramps - bracket inside in front of the bulkhead when not in use * Bolted rear stanchions * Perforated Outer frame angled at approximately 45 degrees with a 2-ton lashing capacity every 480 mm * Installation of 3-ton drop lashing brackets possible every 600 mm * 1 x 10-ton lashing ring in each of the front and rear corners, various holes in the front and end beams for 1.2-ton lashing capacity * One-piece mechanical Grating loading ramps with spring mechanism for one-person operation, approx. 2,750 x 620 mm (can be collapsed to within 20 mm) * Rear approach slope approx. 860 mm * Chassis, drawbar, bulkhead, tailgate, rear folding supports, and loading ramps hot-dip galvanized * Axles, springs, air chamber, and landing gear painted in a single black tone Iodpjpk D D Hjfx Afhsal * Wheelbase: 1,310 mm * Tires: 235/75R17.5 * Side walls painted in RAL 9010 pure white * Side walls painted in a single RAL color available for an additional charge * New vehicle with manufacturer's warranty * Errors and prior sale subject to change * Available for immediate delivery from Egestorf

Condition: new, maximum load weight: 23,700 kg, overall weight: 30,000 kg, axle configuration: 3 axles, * T3 Profi 30.0: * Wabco EBS-E (electronic braking system) * RDÜ tire pressure monitoring * Emergency release device for spring-loaded cylinders * Drum brakes * 3 x 11 ton BPW Eco axles * Air suspension with manual lowering at the rear * Pressure gauge pressure display for determining the load weight (axles separated into 2 air suspension circuits), * Side impact protection * Swivel supports at the rear of the chassis frame * Mechanically adjustable warning sign packages at the front and rear * Front axle closed. Plastic fenders and rear straight galvanized sheet steel aprons, each with splash guard * Reflective contour tape on the side and rear * Hinged lid (hot-dip galvanized) for the toolbox in the bogie platform * LED tail lights * Rotating beacon (removable) at the rear * Pull scissors with 40 mm pull eye and height adjustment via tension spring & turnbuckle * 2 x 7-pin power plugs * 4 stake pockets on each side with simultaneous 2 ton lashing option * La-Si package consisting of: 2 lashing eyes (6.4 ton) at the front left & right on the main frame of the bogie platform, 5 pairs of UVV lashing rings that can be swiveled and lowered, can be loaded in all directions and are embedded in the outer frame - 13.4 ton in the corners, otherwise 10 ton * 6 pairs of mechanical folding booms for 3 mtr. Total width (but not in the rear slope) * Widening planks placed in the middle of the loading area * hydr. one-piece loading ramps (approx. 3,000 x 720 mm) laterally adjustable * Loading area above the turntable: approx. 1,960 x 2,520 mm * Loading height unloaded approx. 1,070 mm * Rear loading area: approx. 6,500 x 2,520 mm Ijdpsl Tpwyofx Afhsal * Loading height unloaded approx. 910 mm (incl. 860 mm approach slope) * Chassis, bogie, drawbar, folding extensions & loading ramps hot-dip galvanized * Axles, turntable, air tank etc. painted in a black tone * Tires 235/75 R 17.5 * Payload approx. 24,000 kg with 30,000 kg total weight * New vehicle with manufacturer's warranty * Errors and prior sale subject to change * Available for immediate delivery from Egestorf

Condition: new, maximum load weight: 14,660 kg, overall weight: 18,000 kg, axle configuration: 2 axles, loading space length: 6,270 mm, loading space width: 2,470 mm, loading space height: 400 mm, Year of construction: 2025, * ETÜ-TA-R 19.0: * Wabco EBS braking system * RDÜ tire pressure monitoring system * Emergency release device for spring brake cylinders * Drum brakes * 2 x 10 t BPW Eco axles * Parabolic springs - 110 mm wide - with tandem compensation unit * Drawbar with 50 mm flange towing eye and height-adjustable drawbar * Jost landing gear at the front * External folding supports at the rear * Lateral underrun protection * Plastic quarter mudguards * 15-pin electrical connector * LED tail lights * 50 mm softwood floor * Fixture in front of the bulkhead for retrofitting container locks * Bolted bulkhead made of smooth sheet metal * Trapezoidal-profiled steel side walls, foldable with tailgate spring assist * Rear steel wall, retractable between the ramps – with internal holder at the front bulkhead when not in use * Bolted rear stanchions * Perforated external frame, bent at approximately 45 degrees, with 2 t lashing capacity every 480 mm * Option to install 3 t folding lashing rings every 600 mm * One 10 t lashing ring in each front and rear corner, various holes in the bulkhead and rear cross member for 1.2 t lashing options * One-piece mechanical grating ramps with spring mechanism for single-person operation, approx. 2,750 x 620 mm (retractable to 20 mm) * Ramp gradient at the rear approx. 860 mm * Chassis, drawbar, bulkhead, rear wall, ramps, and folding supports hot-dip galvanized * Side wall coating in RAL 9010 pure white Isdpfel Th Hwsx Afhsal * Other RAL color options for side walls available at extra cost * Axles, springs, air tanks, flange towing eye, and landing gear painted in black * New vehicle with full manufacturer's warranty * Errors and prior sale reserved * Immediately available from Egestorf

Condition: new, maximum load weight: 10,360 kg, overall weight: 14,400 kg, axle configuration: 2 axles, loading space length: 6,270 mm, loading space width: 2,470 mm, loading space height: 400 mm, Year of construction: 2025, * ETÜ-TA-ER 14.4: * RDÜ (tire pressure monitoring with display option in the truck via EBS signal without truck-side installation) * Electronic braking system EBS * Emergency release device for spring-loaded cylinders * Drum brakes * 2 x 5.5 tonnes Gigant axles * Air suspension with lifting and lowering system * Drawbar height adjustable by 300 mm * Jost landing gear at the front * External hot-dip galvanized folding supports at the rear * Plastic toolbox at the front right, outside the bulkhead * Side impact protection * Plastic quarter fenders * LED lighting system * 15-pin power connector * Hot-dip galvanized chassis, drawbar, bulkhead, and rear wall * 50 mm softwood floor * Provision for retrofitting 20" counterlocks at the front and rear * Bolted smooth sheet metal bulkhead * Trapezoidal steel sheet sidewalls, foldable with side wall spring jack * Bolted hot-dip galvanized rear stanchions * Perforated outer frame, angled at approximately 45 degrees, with a 2-ton lashing capacity every 480 mm, installation of 3-ton drop lashing brackets every 600 mm possible, 1 x 6.3 ton lashing ring in each of the front and rear corners, various holes in the front and end beams for 1.2 ton lashing options Ijdpfx Afopk D Dqehsal * 1 pair of aluminum loading ramps approx. 3,310 x 400 mm (load capacity 8 tonnes per pair) suitable for rubber-tired and tracked vehicles. Storage compartment recessed into the chassis below the loading area from the rear. * Vehicle hot-dip galvanized * New vehicle with manufacturer's warranty * Errors and prior sale subject to change * Available for immediate delivery from Egestorf

Condition: new, maximum load weight: 14,200 kg, overall weight: 19,000 kg, axle configuration: 2 axles, loading space length: 7,000 mm, loading space width: 2,470 mm, loading space height: 400 mm, Year of construction: 2023, * ETÜ-TA-R 19.0: * Wabco EBS-E (electronic braking system) * Emergency release device for spring-loaded cylinders * Drum brakes * 2 x 11 ton Gigant axles * Air suspension * Drawbar with 50 mm flanged towing eye and height adjustment of 110 mm by offset plate * Jost support winch at the front * External folding supports at the rear * Plastic toolbox approx. 750 x 350 x 300 mm, mounted right side * Side underrun protection * Plastic quarter mudguards * 15-pin power plug * LED lights * Reinforcement package for drilling device transport on the chassis * 50 mm softwood floor in clamped design * Fixture in front of the bulkhead for retrofitting container locks * Bolted bulkhead made of smooth sheet metal * Split side walls made of steel sheet - trapezoidal profiled - folding down with folding stanchion in the middle * Steel rear wall, insertable between the ramps - holder for when not in use located inside in front of the bulkhead * Rear stanchions bolted * Perforated outer frame bent at approx. 45 degrees with 2 ton lashing capacity every 480 mm * Installation of 3 ton folding lashing brackets possible every 600 mm * Lashing package: in the corners at the front and rear 1 x 10 ton UVV lashing ring each, on each side 2 x 8 ton UVV lashing rings retractable in the outer frame, various holes in the front and end carrier for 1.2 ton lashing possibility * One-piece mechanical grating ramps with spring system for one-man operation, approx. 3,000 x 620 mm (can be pushed together to 20 mm) Iasdpfx Asl Tp Azefhel * Approach slope at the rear approx. 860 mm * Chassis, drawbar, bulkhead, tailgate, folding supports and ramps hot-dip galvanized * Axles, air tanks, flanged towing eye and support winch painted in a shade of black * Loading height unloaded approx. 940 mm * Loading height loaded approx. 910 mm * Wheelbase: 1,810 mm * Tires: 235/75R17.5 * Side walls painted in RAL 9010 pure white * Painting of the side walls in an RAL color for an additional charge possible * Vehicle has a day registration (without use) * Errors and prior sale reserved * Immediately available from Egestorf on the A7

Condition: new, maximum load weight: 10,900 kg, overall weight: 14,400 kg, axle configuration: 2 axles, loading space length: 6,270 mm, loading space width: 2,470 mm, loading space height: 400 mm, Year of construction: 2025, * ETÜ-TA-R 14.4: * RDÜ (Tire Pressure Monitoring) * EBS electronic brake system * Emergency release device for spring brake cylinders * Drum brakes * 2 x 7 t Gigant axles * Air suspension * Tow bar height adjustable by approx. 300 mm - tow bar extension by 250 mm to 2,250 mm * Jost support winch at front * LED rear lights * Exterior hot-dip galvanized folding supports at rear * Plastic toolbox front right outside at the front wall * Side underrun protection * Plastic quarter mudguards * Hot-dip galvanized chassis and tow bar, front wall, rear wall, tailgate, and loading ramps * 50 mm softwood floor * Mounting fixture in front wall for retrofitting container locks * Bolted front wall made of smooth sheet metal Isdpfoq Dyvyox Afheal * Side walls made of profiled steel sheet - foldable with side wall spring loader * Steel rear wall insertable between ramp holders; when not in use, stored inside at the front wall * Bolted rear stanchions * Perforated outer frame approx. 45 degrees bent with 2 t lashing force every 480 mm, installation of 3 t folding lashing brackets every 600 mm possible, in front and rear corners 1 x 6.3 t lashing ring each, various holes in front and rear cross members for 1.2 t lashing options * One-piece mechanical grid ramp with spring mechanism for one-man operation approx. 2,750 x 600 mm (can be compressed down to 20 mm) * Rear approach angle approx. 860 mm * --Reinforced and certified body according to EN 12642 XL including load securing certificate-- * Side wall color in RAL 9010 pure white * Painting of side walls in other RAL colors possible at extra charge * New vehicle with manufacturer warranty * Errors and prior sale reserved * Immediately available from Egestorf

Condition: new, machine/vehicle number: AHW MT3080, overall weight: 3,000 kg, loading space length: 3,080 mm, loading space width: 1,520 mm, ANHÄNGERWIRTZ, your online pick-up market for new trailers, offers top brand models ready for immediate pick-up! Over 850 new trailers in stock Over 100 used trailers permanently available More than 150 vehicle transporters – popular models with extensive accessory options in stock Non-binding example: Exhibition trailer ready for collection Brenderup Machine Transporter MT 3080 GD 308x152cm 3000kg, low loader with tandem axle, V-drawbar, loading ramp as rear gate with support leg 13-pin plastic connector, 14-inch tires Support wheel, 6 inside lashing rings / 400 daN Digger bucket resting area Non-slip fender covering and running board Hot-dip galvanized, high-quality, sturdy phenolic plywood floor Isdjxq Sbxepfx Afhoal Robust metal wheel chocks, position lighting Recessed lights Spare wheel, including holder below the bucket tray The largest range of transporters available immediately Sales and order acceptance by phone during the day, or 24/7 via our trailer shop All images and descriptions in this advertisement are protected by copyright – logos and brands by trademark law 10/25 39033

Condition: good (used), functionality: fully functional, machine/vehicle number: YGCD160XTF0017195, maximum load weight: 215 kg, first registration: 07/2015, next inspection (TÜV): 11/2027, total length: 6,155 mm, total width: 1,800 mm, total height: 2,300 mm, tire size: 195R14C 106N, color: red, Year of construction: 2015, operating hours: 2,588 h, Feel free to contact us for a detailed quote or to schedule a viewing appointment! Your HEMATEC Arbeitsbühnen GmbH // Official Germany representative for aerial platform manufacturers KLUBB, ISOLI, and DINO, with branches in Dresden, Vehlefanz (near Berlin), Göttingen, and Lauchheim. If you are interested in aerial work platforms, you are also welcome to contact us. Iajdpjxu D Raofx Afhjl