Trailer with working platform

MÜLLER-MITTELTAL T3 Tiefl., Luft., Schwarzdeckentransporte

Condition: new, maximum load weight: 16,400 kg, overall weight: 30,000 kg, axle configuration: 3 axles, Year of construction: 2026, * T3 Profile 30.0: * EBS-E (electronic braking system) * TPMS (tire pressure monitoring system) * Emergency release device for spring accumulators * Drum brakes * 3 x 11-ton BPW Eco axles * Air suspension with lifting and lowering system * SmartBoard as an information tool on the trailer with pressure sensors for displaying total axle load per axle group * Side impact protection * Mechanically adjustable warning sign packages at the front and rear * Front axle with closed plastic mudguards and rear axle with straight, galvanized steel splash guards, each with splash protection * Folding cover (hot-dip galvanized) for the tool box in the turntable platform * Tool box made of galvanized steel sheet, approx. 650 x 300 x 600 mm (black powder-coated), on the right side * 15-pin power connector * LED lighting 12 / 24 V * LED rotating beacon (removable) at the rear * Side marker lights with turn signal control * Drawbar with 40 mm towing eye and height adjustment via tension spring & locking pin * Tire pressure monitoring system with display option in the truck via EBS signal (without truck-side installation) * Rubber covering on the folding ramps and on the access ramps on the left and right (approx. 860 mm long) * Rubber covering on the longitudinal beams from the front to the end beam Fpedpfx Astplv Nekbsk * Hardwood flooring on the running surfaces of the low-loader platform * 4 lashing pockets on each side with simultaneous 2-ton lashing capability * La-Si package consisting of: 5 pairs of UVV lashing rings, swiveling and lowering, loadable in all directions and embedded in the outer frame - 13.4 tons in the corners, otherwise 10 tons * 6 pairs of mechanical folding outriggers for a total width of 3 m (but not in the rear ramp) * Log holder under the loading area in the longitudinal direction * Roller stop in front of the front beam, raised with 1 x 6.4-ton lashing eye on each side * Hydraulic folding ramps (approx. 4,650 x 720 mm) with hydraulically extendable front section and load-holding valves * Hydraulic lateral ramp adjustment * Hydraulic rear supports (single-stage cylinder) * Hydraulic flow divider in the trailer (with hydraulic pump capacity in the truck of over 40 liters up to max. 140 liters/min.) * Hydraulic control block, splash-proof * Two-line hydraulic system * Loading area above the turntable: approx. 1,960 x 2,520 mm * Rear loading area: approx. 6,500 x 2,520 mm (including 860 mm access ramp) * Loading height when loaded: approx. 890 mm +/- 20 mm air suspension * Chassis, turntable, roller stop, folding extensions & access ramps hot-dip galvanized * Axles, turntable, drawbar, air tank, etc. painted in a black tone * Loading height when loaded: approx. 890mm +/- 20mm * New vehicle with manufacturer's warranty * Errors and prior sale excepted * Available from approx. week 45/2026

Condition: as good as new (ex-display), empty load weight: 10,000 kg, maximum load weight: 30,000 kg, overall weight: 40,000 kg, axle configuration: 4x2, loading space length: 9,220 mm, loading space width: 2,540 mm, suspension: air, tire size: 235/75 R17,5, Year of construction: 2025, Equipment: ABS, center pivot plate, trailer coupling, HTD 40K-RM-BM_ Internal dimensions: approx. 9,220 mm x 2,540 mm Overall dimensions: approx. 11,300 mm x 2,540 mm x 3,850 mm Permissible total weight: 24,000 kg Payload: approx. 14,000 kg Tires: 235/75R17.5 inches Loading height: approx. 900 mm Drawbar length: approx. 1,500 mm Coupling height: approx. 820-1,000 mm Ramp angle: approx. 10° Plank length: approx. 3,150 mm Plank width: approx. 750 mm Permissible total weight (special version): 40,000 kg Payload (special version): approx. 30,000 kg Drop-side length: approx. 6,610 mm Overall dimensions (L x W x H): 11,200 Total weight (technical): approx. 44,000 kg Technical axle load: approx. 11,000 kg 6 pairs of lashing points, 3,000 kg per lashing point Lashing points in the drop-side outer frame 4 pairs of lashing points, 3,000 kg per lashing point Lashing/spar pockets, 3 tons in the upper deck outer frame 1 pair of lashing points, 3,000 kg per lashing point Lashing/spar pockets, 3 tons in the drop-side outer frame Suspension Air suspension system including lifting and lowering, acting on the rear axle Braking system Braking system according to EC guidelines with EBS 4S/3M in multi-voltage version (12-24V), spring brake parking brake incl. 2 test connections drawn to the outside for brake/modulator and air spring pressure Electrical system Lighting in LED version with flashing function for side marker lights, Multi-voltage (12-24V) Turntable Solid welded construction with low-maintenance ball bearing race Coupling device Curved drawbar with towing eye Ø 50mm, low-maintenance silent blocks including height adjustment for the drawbar Frame Solid welded construction made of high-strength fine-grained steel Continuous cross members for maximum stability Wheel arches at the front (length at the top approx. 2,500 mm - depth approx. 410 mm) and at the rear (length at the top approx. 1,470 mm - depth approx. 370 mm); without wheel arch covers Excavator well (length 1,650mm, width 750mm, depth 190mm) Wheel cutouts above the rear wheels with wheelbase 2,010, corners beveled at the front, climbing strips on the rear of the ramp for maximum safety during loading and unloading 4 pairs of spar pockets (90x50)mm in the outer frame - upper deck 1 pair of spar pockets (90x50)mm in the outer frame - drop-side Floor 50 mm softwood decking (painted/impregnated) Fjdpfx Ajiciutekbepk Ramps One-piece, hot-dip galvanized ramps (3,150mm x 750mm) with 50 mm softwood decking (painted/impregnated), laterally displaceable, direct-acting spring lifts for easiest operation Finishing Chassis frame hot-dip galvanized Supports 2 folding supports at the rear left and right at the vehicle rear Equipment Folding side guard, at the front, semi-circular plastic mudguards - at the rear, straight steel mudguards with anti-spray flaps, 2 wheel chocks with holder; contour marking according to ECE directive R48 Wheel arch cover at the front with 3 pairs of spar pockets, without covering (cover can be recessed under the longitudinal beams) 975.00888 Hardwood covering for RM cover at the front Wheel arch cover at the rear with 1 pair of spar pockets, without covering (cover can be recessed under the longitudinal beams) 975.00897 Hardwood covering for RM cover at the rear 3 pairs of lashing rings 6 tons, bolted 3 m equipment package without ramp, W=11200 Folding outrigger with softwood planks 970.04199-36 Warning package LED HTD curved Aspöck warning signs 4-way, electrical system and rotating beacon 1 pair of storage compartment for wooden planks, 3m packa

Condition: new, empty load weight: 9,650 kg, maximum load weight: 30,350 kg, overall weight: 40,000 kg, axle configuration: > 3 axles, loading space length: 9,740 mm, loading space width: 2,550 mm, suspension: air, tire size: 235/75 r17,5 zoll, Year of construction: 2026, Equipment: ABS, center pivot plate, 4-AXLE LOW LOADER IN TOP CONDITION! Fodpshvxgzefx Akbspk => HOT-DIPPED GALVANISED (CHASSIS FRAME, TURNTABLE FRAME, RAMP) => FULL AIR SUSPENSION => WITH LIFTING AND LOWERING FUNCTION (REAR AXLE UNIT!) => SAF LOW LOADER AXLES => LASHING PACKAGE => HOLE-PUNCHED OUTER FRAME FOR ADDITIONAL LASHING POINTS => CLIMBING STRIPS IN THE REAR AREA OF THE RAMP => 6 LASHING POINTS IN THE EXCAVATOR ARM RECESS IN THE REAR AREA => LONG, ONE-PIECE RAMPS => SHALLOW RAMP ANGLE Permissible total weight 40,000 kg Payload approx. 30,350 kg Chassis frame hot-dip galvanised Turntable frame hot-dip galvanised Ramps hot-dip galvanised Air suspension SAF axle with drum brake EBS electronic braking system Tyres 235/75R17.5 – 16 ply Low bed length approx. 7160 mm Recess for excavator arm storage, approx. 3000 mm x 730 mm x 180 mm in the rear area of the low bed 4 pairs of recessed lashing rings 10 tonnes in the low bed 2 pairs of recessed lashing rings 10 tonnes in the upper bed 4 pairs of lashing points 3 tonnes in the outer frame of the low bed 3 pairs of lashing eyes 6 tonnes on the outer frame 4 pairs of spar pockets in the outer frame of the upper bed 4 pairs of spar pockets in the outer frame of the low bed 3-metre widening kit with folding outriggers without slope 4 x warning signs with lighting Rotating beacon at the rear LARGE STEEL STORAGE BOX under the loading platform 2 storage compartments with folding lids in the upper platform Hydraulic ramp lifters One-piece ramp approx. 3150 x 750 mm Softwood flooring for loading platform and ramps 40,000 kg GVW only with special permit according to §70 => Delivery costs: 2.90 euros plus VAT per km => Prices are ex D-86368 - Gersthofen Your direct contact: Mr. Hauptmann Tel. DOLL VEHICLE CONSTRUCTION *Subject to prior sale and changes!* *Price valid ex D-86368 - Gersthofen* *Sale only to commercial customers!* *Images may vary and are for general guidance only => may include/show accessories at an additional cost*

Condition: used, machine/vehicle number: GE11/142/2022, empty load weight: 6,350 kg, maximum load weight: 17,650 kg, overall weight: 24,000 kg, axle configuration: 3 axles, first registration: 08/2008, loading space length: 8,500 mm, loading space width: 2,500 mm, suspension: air, Very well-maintained vehicle from first owner Three-axle low-loader trailer Low-loader with drive-up ramp Heavy-duty transport Model T3 Komakt 30.0 Length 8,500 mm Width 2,500 mm Air suspension Fedon Aw Hkepfx Akbspk Commercial/export net price – €15,990 Subject to changes, interim sale, and errors ===== Phone2 Mobile =====

Condition: used, maximum load weight: 10,870 kg, overall weight: 14,400 kg, axle configuration: 2 axles, first registration: 06/2025, loading space length: 5,000 mm, loading space width: 2,420 mm, loading space height: 500 mm, Year of construction: 2023, Equipment: ABS, KA-TA-R 14.4: ----Brakes: * Wabco ABS * Emergency release device for spring-loaded cylinders * Drum brakes ----Axles: * 2 x 7 t Gigant axles Fpjdpfx Akol Th Duobok ----Suspension: * Parabolic springs with tandem equalizing unit ----Drawbar / Flange eye: * Height-adjustable drawbar (approx. 300 mm) with 40 mm flange towing eye ----Electrics / Lighting: * 15-pin power connector * Multi-chamber rear lights ----General attachments: * Jost mechanical landing gear at the front * 2 mechanical folding supports at the rear * Plastic toolbox approx. 650 x 350 x 320 mm, mounted front right side on the chassis * Bolt-on underrun protection * Plastic quarter mudguards * Net hooks at each central locking bearing and 2 at the front wall ----Chassis: * High-tensile steel chassis ----Tipping body: * Steel pallet 3-way tipping body, continuous side walls, upper part with internal tube reinforcement – no central stanchions, foldable with drop-side spring assist * Bolt-on rear stanchions * Combination steel swing rear doors, 2-leaf asymmetrical design, can swivel and lock to 270° – non-foldable – with additional pendulum frame for automatic tailgate release during tipping operation, latching via galvanized rotary bar lock at the rear and central locking. Deactivation function for automatic tailgate when tipping backwards with open swing door * 4 mm high-tensile steel floor plate * Rear guide rail for loading ramps ----Load securing: * Each corner with 1 x 5 t lashing ring, 4 x 3 t lashing eyes per side integrated into outer frame ----Ramps: * 1 pair of aluminium loading ramps approx. 3,570 x 410 mm (load capacity 10 t/pair), suitable for rubber-tyred & tracked vehicles * Lockable storage compartment for ramps under the loading area, integrated into the chassis at the rear ----Tyres: * Tyres 285/70 R19.5 ----Paintwork: * Chassis, drawbar, underrun protection, rear stanchion, folding supports at rear hot-dip galvanized * Axles, springs, air reservoir, and landing gear painted in black * Side boards painted RAL 9010 pure white * Side walls can be painted in other RAL colours for an additional charge ----Information: * Reinforced body, with load securing certificate * Vehicle comes with day registration (not in use) * Subject to errors and prior sale ----Delivery time: * Immediately available from Egestorf

Condition: new, maximum load weight: 23,940 kg, overall weight: 30,000 kg, axle configuration: 3 axles, loading space length: 8,460 mm, loading space width: 2,520 mm, Year of construction: 2026, * T3 Profi 30.0 ----Brakes: * EBS braking system * Emergency release system for spring brake cylinders * Drum brakes ----Axles: * 3 x 11-ton Gigant axles ----Suspension: * Parabolic springs with mechanical axle compensation at the rear ----Drawbar: * Drawbar with 50 mm drawbar eye and height adjustment via coil spring & tension lock ----Lighting / Electrical System: * TPMS tire pressure monitoring system * Multi-voltage system * LED tail lights 12 / 24 V * Rotating beacon (removable) at the rear * 15-pin power connector ----General Components: * Side impact protection * Swivel supports at the rear on the chassis frame * Mechanically adjustable warning sign packages at the front and rear * Front mudguards made of plastic and rear mudguards made of straight, galvanized steel sheet, each with splash protection * Tool box made of galvanized steel sheet - black powder-coated - approx. 650 x 300 x 600 mm * Hinged lid (hot-dip galvanized) for the tool box in the turntable platform * 4 lashing points on each side (but no lashing bars included) with simultaneous lashing capability ----Load Securing (La-Si package consisting of): * 2 lashing points (6.4 tons) at the front left & right on the main frame of the turntable platform * 6 pairs of UVV lashing rings, swivel and lowerable, loadable in all directions and recessed in the outer frame * 13.4 tons in the corners, otherwise 10 tons ----Widening: * 6 pairs of mechanical folding outriggers for a total width of 3 meters (but not in the rear slope), * Widening boards placed in the middle of the loading area ----Ramps: * Hot-dip galvanized, one-piece hydraulic ramps (approx. 3,000 x 720 mm), mechanically adjustable on the side * 4-way control block for retrofitting of the hydraulic side ramp adjustment ----Loading Area: * above the turntable: approx. 1,960 x 2,520 mm & unladen approx. 1,070 mm * rear loading area: approx. 6,500 x 2,520 mm & unladen approx. 910 mm (incl. 860 mm approach angle) ----Tires: * 235/75 R 17.5 twin tires Fpjdpfx Akol Th I Ajbek ----Unladen Weight: * approx. 5,980 kg unladen weight ----Painting: * Chassis, turntable, drawbar and ramps hot-dip galvanized * Axles, springs, air tanks etc. painted in a black shade ----Information: * Technically possible gross vehicle weight of 30,000 kg * New vehicle with manufacturer's warranty * Errors and prior sale excepted ----Delivery time: * Immediately available from Egestorf