Trailer with working platform

MÜLLER-MITTELTAL 3-Achs Plateau, luftgefedert, hydr. Rampen

Condition: new, maximum load weight: 23,500 kg, overall weight: 30,000 kg, axle configuration: 3 axles, loading space length: 8,380 mm, loading space width: 2,520 mm, Year of construction: 2026, * PT 30 Profile: ----Brakes: * EBS (electronic braking system) * Emergency release device for spring brake cylinders * Drum brakes ----Axle: * 3 x 11-ton Gigant axles ----Suspension: * Air suspension with lifting and lowering system and RtR valve ----Drawbar: * Drawbar 1,200 mm long with 40 mm drawbar eye and height adjustment via tension spring & locking bolt ----Electrical system / Lighting: * Smart board mounted on the trailer as an information tool (for axle load display - separate display for front and rear) * Tire pressure monitoring system with display option in the truck via EBS signal without truck-side installation * 15-pin power connector * LED lighting 12 / 24 V Bjdpfx Aexptn Rsbvodg * LED rotating beacon (detachable) at the rear ----General components: * Lateral impact protection * Swivel supports at the rear of the chassis frame * Mechanical adjustable warning sign packages at the front and rear * Front plastic quarter fenders with splash guard * Rear straight galvanized steel side skirts with splash guard * Toolbox made of galvanized sheet steel, approx. 650 x 300 x 600 mm, black powder-coated, on the right side * Box in the turntable for accessories with hinged lid, 2 continuous locking mechanisms, permanently installed (directly behind the turntable platform) * 2 pieces of galvanized steps on the turntable, left + right ----Low-loader platform: * ROBOTER welded ANTI-SLIP coating on the steel plate of the turntable platform (protruding weld beads) ----Load securing (La-Si package consisting of): * 2 lashing eyes (13.4 tons) at the front left & right on the front wall beam * 1 pair of UVV lashing rings (13.4 tons) at the front & rear, as well as 3 pairs of UVV lashing rings (10 tons) on each side, swivel and lowerable, loadable in all directions and recessed in the outer frame * 3 rung pockets on each side with simultaneous 2-ton lashing option * Profifix lashing rail in the longitudinal axis in the middle, in the level area for lashing up to LC 3000 daN ----Extension: * 6 pairs of mechanical folding outriggers for a total width of 3 meters (but not in the rear slope) * Extension boards placed in the middle of the loading area ----Ramps: * Hydraulic, single-piece ramps, approx. 3,000 x 720 mm * Mechanical, adjustable on the side * Control block 4-way for later retrofitting of hydraulic ramp displacement ----Excavator arm rest: * Excavator arm rest extending across the rear axle to the end crossbeam (total length approx. 2,100 mm) * 2 pairs of lashing eyes LC 6400 daN in the excavator arm rest on the side in the longitudinal frame ----Loading height: * Loaded approx. 910 mm +/- 20 mm air suspension ----Painting: * Chassis, turntable, folding outriggers, support legs and ramps hot-dip galvanized * Axles, slewing ring, air tank, drawbar eye painted in a black tone ----Information: * New vehicle with manufacturer's warranty * Errors and prior sale reserved ----Delivery time: * Available from approx. week 45/2026

Condition: used, empty load weight: 10,900 kg, maximum load weight: 43,600 kg, overall weight: 54,500 kg, axle configuration: > 3 axles, first registration: 04/2025, loading space length: 8,700 mm, loading space width: 2,550 mm, loading space height: 855 mm, tire size: 245/70 r17.5, color: grey, Year of construction: 2025, operation weight: 10,900 kg, Equipment: ABS, Gooseneck, rigid, in center tube design: -Closed outer frame with cutouts for lashing straps (LC 1,500 daN) -Steel floor with anti-slip surface -Including rail for aluminum ramps -2" – Kingpin -Mechanically operated BPW landing gear -550 mm long, 8’ bevel at the end of the gooseneck -Front bulkhead incl. parking position for rear wall, 400 mm high -Spare wheel holder mounted vertically on the front of the gooseneck -3 pairs of lashing rings LC 5,000 daN recessed in the loading platform of the gooseneck -Aluminum stake sides 400 mm high, consisting of 2 x side boards length 3,150 mm and rear board with rails (galvanized) -Storage box rectangular, aluminum, hinged lid, lockable, dimensions approx. 400 x 800 mm, center -Storage box 45’, aluminum, hinged lid, lockable, dimensions approx. 400 x 800 mm, left -Storage box 45’, aluminum, hinged lid, lockable, dimensions approx. 400 x 800 mm, right Bdodpfxji Ai E Rj Abvjg Loading platform, single telescoping: -Closed outer frame with cutouts for lashing straps (LC 1,500 daN) -Fixed section at the front 700 mm -Sheet metal floor with anti-slip surface -Beveled interface between fixed section and loading platform for attaching bridge planks and wheel recesses -Excavator recess incl. elongated holes for securing the load (LC 1,500 daN), length approx. 3,850 mm -Preparation for hydraulic ramp (electrical supply) -Supports for widening to 3,000 mm -Beveled vehicle rear 8°, 550 mm long -Sled design for easy installation and removal of ramps -Continuous mudflap at the rear -1 pair of lashing points LC 10,000 daN in the center of the loading platform behind the gooseneck -7 pairs of lashing points LC 10,000 daN in the outer frame of the loading platform -6 pairs of rail pockets 100 x 50 mm in the outer frame of the loading platform -1 pair of lashing points LC 10,000 daN in the center in the rear area of the loading platform -1 pair of rail pocket strips approx. in the center of the loading platform -1 pair of rail pocket strips on the fixed section -1 pair of rail pocket strips behind the last axle Ramps: -Hydraulic double folding ramps, 2,750+1,500x800 mm -Wood deck larch -Control via remote control (possible via cable and radio) -Ramps with quick-change (dismantling system) Chassis: -Axle manufacturer BPW ECO Max -2 ride heights -4 axles á 10 t (technically 12 t) -Twin tires 245/70 R17.5 -2 x fixed axle and 2 x friction-steered axle -Reverse steering lock of the friction-steered axle via reverse gear -Brake system manufacturer Knorr (according to EU regulations with EBS-E) -TIM G2 from Knorr (Trailer Information Module) -Vehicle stability control RSS (Roll Stability Support) -Load-dependent lift axle on the first axle incl. starting aid (forced lowering of the lift axle via TIM possible) Accessories: -4 chocks with holder -2 pairs of warning signs 423 mm x 423 mm, with 2 position lights and socket for rotating beacon, steplessly adjustable up to 3,950 mm -Mounting options on the gooseneck and on the loading platform (alternatively on the ramp, if available) are included -Plug-in partition sheet at the end of the excavator recess -Electro-hydraulic unit for ramp operation -Ramp operation via wireless remote control -Hydraulic support legs at the rear of the vehicle for support during the loading process -1 pair of additional reversing lights rear, switched on in reverse gear -Wood widening planks - larch (option)

Condition: new, maximum load weight: 36,020 kg, overall weight: 45,000 kg, axle configuration: 3 axles, loading space length: 13,600 mm, loading space width: 2,540 mm, suspension: air, tire size: 435/50 R 19.5, color: grey, Equipment: ABS, Loading platform: Loading area in extendable design with pneumatically confirmed locking mechanism 2 pairs of lashing rings (LC 5,000 daN) 1 pair of lashing rings (LC 10,000 daN) 6 pairs of lashing rings can be folded outwards (LC 5,000 daN) 2 pairs of lashing rings can be folded outwards (LC 10,000 daN) Cut-outs in the outer frame of the cargo bed for attaching lashing straps Brake system: Brake system in accordance with EU regulations with EBS-E (2S2M) without connecting lines to the tractor unit Paintwork: First-class and long-lasting corrosion protection of the standard shot-blasted welded frame guaranteed by a 2-component (2K) zinc dust primer A high-quality 2-component (2K) top coat in one color Rear section metallized and painted in RAL 9010 (pure white) Metallic paint is not possible Seat posts: JOST seat posts (mechanical) with 2-speed gearbox for 24t lifting load (50t test load) Steel construction: Steel construction made of high-strength fine-grained steels. Steel grades: Bsdpfei Dwlwjx Abvedg S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa) Electrical system: Electrical system in accordance with EU regulations, 24 volt lighting ASPÖCK-NORDICK (ASS3) ASPÖCK-UNIBOX on the connection strip at the front with 24N, 24S & 15-pin sockets Connection according to ISO 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Axles and tires: BPW axles, air-sprung, with disc brakes (377 mm), with lifting/lowering function The self-steering axles with electromagnetic reverse lock can be activated via reverse gear or manually Axle tool. Tires 435/50 R 19.5 Accessories included: Yellow-red air couplings on the galvanized connection strip at the front 2 wheel chocks with bracket 2" kingpin One galvanized steel bulkhead approx. 1,600 mm high. EN12642-XL. Yellow reflector tape in accordance with EU regulations on the side, on the extension and at the rear of the trailer European reflector plates (red/yellow) at the rear of the trailer Loading area with approx. 38 mm thick hardwood floor 10 pairs of stanchion pockets for 100 x 50 mm stanchions in the outer frame of the cargo bed 1 spare wheel holder under the cargo bed on the right in the direction of travel Manual and description on USB stick One mud flap at the rear of the trailer A bracket for a rotating beacon at the rear of the trailer A holder for the warning signs on the gooseneck and on the rear panel on the left and right, including a socket One INOX toolbox transversely under the loading area (1,000 x 400 x 2,500 mm) 6 pairs of WADER container pockets in the loading area, for 1x 20ft container, 2 x 20ft containers or 1 x 40ft container, an additional locking point is provided in the pull-out for a 45ft container 3 pairs of stanchion pocket rails, mounted transversely in the cargo bed, for 100 x 50 mm stanchions Rear speed sticker 60 km/h. 2 reversing lights mounted on the rear panel Four warning signs extendable by approx. 400 mm approx. 423 x 423 mm with a position light A bracket for rotating beacon on the warning signs HRM metallization (High Resistance Metallization) of the outer frame Complete steel construction shot-blasted, then the defined visible surfaces are hot-finished with ZINACOR 850 metallization (zinc 85% - aluminium 15%)

Condition: new, empty load weight: 10,600 kg, maximum load weight: 39,400 kg, overall weight: 50,960 kg, axle configuration: > 3 axles, loading space length: 9,300 mm, loading space width: 2,540 mm, loading space height: 760 mm, suspension: air, tire size: 205/65 R17.5, color: grey, operation weight: 10,600 kg, Equipment: ABS, Gooseneck: -Gooseneck with hardwood covering, 30 mm thick -Gooseneck at the rear, straight design -3 pairs of lashing rings (LC 5,000 daN) Loading area in extendable design: -Loading area in extendable design -5 pairs of lashing rings that can be folded outwards -3 pairs of lashing rings that can be folded outwards -1 pair of lashing rings lying in the front of the loading area -Cutouts in the outer frame of the loading area for hanging tensioning straps -Hardwood covering, approx. 48 mm thick, checkered sheet covering over the axles Seatposts: -JOST seatposts (mechanical) with 2-speed gearbox for 24t lifting load (50t test load) Axles and tires: -BPW axles, two axles rigid, two axles with self-steering -Air suspension, with drum brake, with lifting/lowering- Function -The self-steering axles with electro-magnetic reversing lock can be activated via reverse gear or manually -Axle tool -Tires 205/65 R17.5 Braking system: -Braking system in accordance with EU regulations with EBS-E (4S3M) Steel construction: -Steel construction made of high-strength fine-grain steels -Steel qualities: -S355J2+N/S355MC (yield strength 355MPa) -S690QL/S700MC (yield strength 690MPa) Electrical system: -Electrical system in accordance with EU regulations, lighting 24 volts, ASPÖCK-NORDIK (ASS3) -ASPÖCK-UNIBOX on the front connection strip with 24N, 24S & 15-pin sockets -Connection in accordance with ISO: -24N ISO-1185 -24S ISO-3731 -15-pin ISO-12098 Painting: -First-class and long-lasting corrosion protection of the standard shot-blasted welded frame guaranteed by a 2-component (2K) zinc dust primer -A high-quality 2-component (2K) top coat in a single color in Nova gray -Rear section metallized and painted in RAL 9010 (pure white) Bedpfx Abst Ag Uwjvedg Accessories included: -A spare wheel with holder in front of the bulkhead -2" kingpins -A galvanized steel bulkhead approx. 400 mm high -Yellow-red air couplings on the galvanized connection strip at the front -4 brake shoes with holder on the bulkhead -Galvanized folding supports under the bevel of the loading area -A bracket for a rotating beacon at the rear of the trailer -Galvanized extensions, extendable by approx. 230 mm on each side -White Reflective tape in accordance with EU regulations on the side, on the extension and at the rear, red -On the gooseneck and on the rear panel on the left and right, a holder for the warning signs including a socket -European reflector signs (red-yellow) on the rear of the trailer -TPMS tire pressure monitoring system in accordance with ECE R 141 -ALU side walls and rear wall can be plugged into the gooseneck, approx. 2,440 x 400 mm -The rear, galvanized plug-in stanchions are removable, length of the structure approx. 2,560 mm -7 pairs of WADER container bags -1x 20ft container in the loading area; 1x 40ft container in the loading area; 1x 40ft container above the gooseneck; 2x 20ft containers -7 pairs of stake pockets for 100 x 50 mm stakes in the outer frame of the loading area -Lift axle on the front axle with control by TEBS E depending on the current axle load and the current loading status -Movable mounting rail for aluminum loading ramps at the rear of the vehicle -A painted layer of sand on the checker plates on the gooseneck and on the loading area to prevent slipping -Four warning signs, approx. 423 x 423 mm, extendable by approx. 400 mm, with a position light -A holder for a rotating beacon on the warning signs -Speed sticker 80 km/h at the rear and on both sides -L

Condition: new, empty load weight: 7,900 kg, maximum load weight: 41,600 kg, overall weight: 49,500 kg, axle configuration: 3 axles, loading space length: 8,600 mm, loading space width: 2,540 mm, loading space height: 860 mm, suspension: air, tire size: 235/75 R 17,5, color: grey, operation weight: 7,900 kg, Equipment: ABS, Gooseneck: -Gooseneck with rear bevel of approx. 750 mm x 10° -3 pairs of lashing rings (LC 5,000 daN) -Hardwood decking 30 mm thick Loading area: -Loading surface with rear slope of approx. 1,000 mm x 8° -Recess in the chamfer and protruding into the loading surface to accommodate the excavator dipper stick approx. 2,900 x 750 x 210/290 mm Cut-outs in the outer frame of the cargo bed for attaching tensioning straps -Hardwood flooring approx. 48 mm thick, checker plate flooring over the axles Seat posts: -JOST fifth-wheel supports (mechanical) with 2-speed gearbox for 24 t lifting load (50 t test load) Axles and tires: -BPW axles and suspension, 2 axles rigid, 1 axle self-steering -Technical axle load: 12,000 kg -Electromagnetic reverse lock via reverse gear and can be activated manually -Air suspension with lifting and lowering valve -TPMS tire pressure monitoring system in accordance with ECE R 141 -235/75 R 17.5 tires Bdedpfxeunrape Abvsg Paint finish: -Complete steel construction automatically blasted after welding with blast wheel system -second blasting with corundum for optimum adhesion of the coating system -Finishing coat with 2 layers of 2K top coat, single color in RAL MB 7350 nova grey -Rims painted in silver -Rear section metallized and painted in RAL 9010 (pure white) -Sealing of cavities with special wax Electrical system: -Electrical system in accordance with EU regulations, lighting 24 volt ASPÖCK-NORDIK (ASS3) ASPÖCK-UNIBOX at the front connection strip with sockets 2x 7-pin & 1x15-pin Accessories included: -Extensive lashing positions -2" kingpin -One galvanized steel end wall approx. 400 mm high -Yellow-red air couplings on the galvanized connection strip at the front -4 restraining shoes with holder on the bulkhead -Mounting in the rear area of the gooseneck for ALU docking ramps -Galvanized folding supports under the bevel of the cargo bed -One bracket for a rotating beacon at the rear of the trailer -Galvanized extensions, extendable by approx. 230 mm per side -White reflector tape in accordance with EU regulations on the sides and red at the rear -On the gooseneck and on the rear plate on the left and right, one bracket each for the warning signs including socket -ALU drop sides and rear panel can be plugged onto the gooseneck approx. 2,440 x 400 mm -The rear, galvanized stanchions are removable -2 pairs of WADER container pockets in the loading area for a 20ft container -6 pairs of stanchion pockets for 100 x 50 mm stanchions in the outer frame of the cargo bed -Sliding attachment strip for ALU docking ramps at the rear of the vehicle -Square climbing rails 20 x 20 mm every 200 mm on the outer frame of the loading area slope -a layer of sand painted onto the chequer plates on the gooseneck and on the cargo bed to prevent slipping -Four warning signs that can be extended by approx. 400 mm, approx. 423 x 423 mm with a position light -One bracket for rotating beacon on the warning signs -Speed sticker 80 km/h at the rear and on both sides -European reflector plates (red/yellow) at the rear of the trailer -Manual and description on USB stick -HRM metallization (High Resistance Metallization) of the outer frame -Complete steel construction shot-blasted, then the defined visible surfaces hot-finished in metallization with ZINACOR 850 (zinc 85% - aluminium 15%)