Used Work Platform Trailers for sale (72)

Condition: new, maximum load weight: 30,740 kg, overall weight: 40,000 kg, axle configuration: > 3 axles, Year of construction: 2026, * T 4: * Wabco EBS-E (electronic braking system) * RDÜ tire pressure monitoring system * Emergency release device for spring brake cylinders * Drum brakes * 4 x 11 t Gigant axles * Air suspension with lifting and lowering device and RtR valve * SmarD on-board system for load weight determination * Warning sign packages front & rear * Reflective contour tape on sides and rear * Removable rotating beacon at the rear * LED lights * Straight drawbar with 50 mm towing eye and infinitely adjustable height * Tool box made of powder-coated steel and spare wheel holder in basket design, mounted on the right side * Enclosed plastic single fenders at the front * Straight steel mudguards at the rear, each with spray suppression (anti-spray system) * Side underrun protection Hnodpfx Aajl Tik Noajk * Turntable platform extended by 520 mm with 45° corners and 3 integrated storage compartments incl. cover, lockable * Chassis made of high-strength fine-grained steel * Floor over turntable platform made of 50 mm softwood, in the low-bed platform made of 60 mm softwood * Outer planks of the loading ramps made of hardwood * 4 stake pockets on each side (no stakes included) with simultaneous 2 t lashing point per pocket * Load securing package consisting of: 2 lashing points 6.4 t at the front left and right on the main frame of the turntable platform * 2 pairs of 13.4 t lashing rings each at the outer frame front and rear, as well as 4 pairs of 10 t lashing rings per side, swiveling and retractable * Loadable in all directions and recessed into the outer frame * 2 pairs of 6.4 t lashing rings in the excavator arm rest area * 8 pairs of galvanized swing-out marker boards for 3 m total width (not at the rear slope) * Widening planks stored in a compartment on the left side * Excavator arm rest above rear axle up to end of approach ramp approx. 2,100 x 740 x 190 mm * Mechanical drop-down supports at the rear * Hydraulic folding ramps with hydraulically adjustable tip, approx. 4,650 x 720 mm incl. hydraulic lateral ramp shifting and load-holding valve * Loading area across the turntable: approx. 2,990 x 2,520 mm * Rear loading area: approx. 6,780 x 2,520 mm * Loading height loaded: approx. 890 mm, +/- 20 mm (incl. 860 mm approach slope) * Flow divider installed * Chassis, turntable, access ramps, flip-out marker boards and mechanical drop-down supports hot-dip galvanized * Axles, drawbar, air tanks, and turntable painted in black * Tires: 235/75 R 17.5 * New vehicle without first registration, with manufacturer warranty * Subject to errors and prior sale * Immediately available ex Egestorf on the A7

Condition: new, maximum load weight: 23,830 kg, overall weight: 30,000 kg, axle configuration: 3 axles, loading space length: 8,460 mm, loading space width: 2,520 mm, Year of construction: 2026, * T3 Profile 30.0: * EBS braking system * RDÜ tire pressure monitoring system * Emergency release device for spring brake cylinders * Drum brakes * 3 x 11 t BPW Eco axles * Parabolic springs * Mechanical axle compensation at the rear * Side underrun protection * Swivel support legs at the rear of the chassis frame * Mechanically adjustable warning sign packages at front and rear * Front axle with closed plastic mudguards, rear axle with straight galvanized steel skirts, each with splash protection * Reflective contour tape on the sides and rear * Folding lid (hot-dip galvanized) for the toolbox on the turntable platform * Multi-voltage system * LED tail lights * Removable beacon at rear Hnsdpfjx Ipb Hjx Aaaek * Drawbar with 40 mm towing eye, height adjustment via tension spring and turnbuckle * 15-pin electrical connector * Four stake pockets per side (no stakes provided), each also suitable as lashing points * Load securing package including: 2 lashing rings (6.4 t) at the front left & right on the main frame of the turntable platform, 5 pairs of UVV-compliant lashing rings, swiveling and retractable, loadable in all directions and recessed into the outer frame—13.4 t in corners, otherwise 10 t * 6 pairs of mechanical swing-out extensions for 3 m overall width (excluding the rear slope) * Widening boards stored in the center of the loading area * Excavator arm rest above rear axle up to end crossmember approx. 2,100 mm long (2 pairs of 6.4 t lashing rings on the sides in the excavator arm rest) * Hydraulic one-piece loading ramps (approx. 3,000 x 720 mm) * Hydraulic lateral ramp displacement * Loading area above turntable: approx. 1,960 x 2,520 mm * Loading height unladen approx. 1,070 mm * Rear loading area: approx. 6,500 x 2,520 mm * Loading height unladen approx. 910 mm (including 860 mm drive-on slope) * Chassis, turntable, drawbar, and loading ramps hot-dip galvanized * Axles, springs, air tanks, etc. painted in black * 235/75 R 17.5 twin tires * Unladen weight: 5,900 kg * --Technical permissible total weight of 30,000 kg-- * Vehicle is hot-dip galvanized * New vehicle with manufacturer’s warranty * Subject to errors and prior sale * Immediately available ex works Egestorf on the A7

Condition: used, maximum load weight: 31,250 kg, overall weight: 40,000 kg, axle configuration: > 3 axles, first registration: 07/2014, loading space length: 9,010 mm, loading space height: 900 mm, total width: 2,550 mm, Year of construction: 2014, Equipment: ABS, 4-axle Schwarzmüller T4 Low Loader Trailer VIN: EZ346388 Chassis / Attachments: * Leaf spring suspension * 4 x SAF axles with drum brakes * Tyres: 235/75 R 17.5 * Tyre tread depth: 1.~60% 2.~60% 3.~60% 4.~50/20% Body: * Total length: 9.1 m * Extendable lateral outriggers (up to 3.0 m) * Ride height: 0.90 m * Hydraulic loading ramps with lateral shift * Various lashing points available Hnjdpfsyumbvjx Aaaok Weights: * Gross weight: 40,000 kg * Unladen weight: 8,750 kg * Payload: 31,250 kg Other: * German vehicle * 1 previous owner * Safety inspection valid until 09/2026 * New general inspection (TÜV) possible upon request ---- New general inspections / safety checks or weight reductions/increases are available upon request. We are happy to assist you in obtaining export/transfer license plates, and we can also arrange for transportation of your purchased vehicles within Germany. Please contact us! ---- We speak the following languages: German, English, and Russian! ---- No liability for printing or typographical errors. Subject to change, prior sale, and errors! ---- Who are we? Leible Nutzfahrzeuge is a family-run business based in Kehl am Rhein. With our many years of experience in the refurbishment and sale of commercial vehicles, we are a reliable partner for customers worldwide. Leible Nutzfahrzeuge specializes in the sale of new and used commercial vehicles. On our 11,000 m² premises, you will find a wide selection of vehicles. Our company philosophy is characterized by fairness and reliability. As customer satisfaction is very important to us, we offer an excellent all-round service package and provide a competent contact person to guide you through the purchase or sale of vehicles. See for yourself! Our services for you: Loading of vehicles We are happy to assist you with loading your purchased vehicles. Organizing special transports We are happy to assist you in organizing special transports. Temporary/export license plates We are happy to assist you in obtaining export/short-term license plates.

Condition: new, maximum load weight: 10,950 kg, overall weight: 14,400 kg, axle configuration: 2 axles, loading space length: 6,270 mm, loading space width: 2,470 mm, Year of construction: 2026, * ETÜ-TA-ER 14.4 Flatbed: Hnjdpfsv D Tbksx Aaask ----Brakes: * EBS (Electronic Braking System) * Emergency release device for spring actuators * Drum brakes ----Axles: * 2 x 7 t BPW axles ----Suspension: * Air suspension with lift and lower function ----Drawbar / Flange Drawbar Eye: * Height-adjustable drawbar, adjustable by approx. 300 mm * Drawbar shortened by approx. 200 mm to approx. 1,800 mm (resulting in B-dimension approx. 8,080 mm) * 40 mm flange drawbar eye ---- Electrics / Lighting: * 15-pin power connector * LED lighting system 12 / 24 V * 2 additional LED reversing lights at the rear (controlled by reverse gear) * 1 removable LED rotating beacon (incl. bracket) at the rear * TPMS (Tire Pressure Monitoring System) ----General Attachments: * Mechanically adjustable 3 m warning sign panels front and rear * Landing leg at the front * Rear folding supports (external) * Plastic toolboxes approx. 750 x 350 x 300 mm each, left and right side * Side underrun protection * Rear underrun protection * Plastic quarter mudguards ----Loading platform: * 400 mm high bolted front wall * 50 mm softwood floor * 2 pairs of container locks (extendable to 3 m external container width) and lockable, locking dimension retracted according to ISO - DIN 15190 = 2,259 mm. Container locks extended = 2,819 mm (this dimension is not DIN compliant) with an absolute external width of 3,000 mm ----Load securing: * Perforated outer frame angled at approx. 45 degrees with 2 t lashing capacity every 480 mm * Installation of 3 t drop lashing loops every 600 mm possible - 5 x 3 t UVV lashing loops fitted on each side - * In each corner, front and rear, 1 x 6.3 t lashing ring (front directly behind the container locks in the wooden floor and rear in the end cross member) * Various holes in the front and rear cross members for 1.2 t lashing options ----Ramps: * 1 pair of aluminium slide-in ramps approx. 3,570 x 410 mm (load capacity 10 t/pair), suitable for rubber-tyred and tracked vehicles * Rear access storage compartment integrated under the loading area within the chassis ----Paintwork: * ---Chassis, drawbar, front wall, underrun protection, and rear supports hot-dip galvanized--- * Axles, air tanks, front landing leg, and flange drawbar eye finished in black tone ----Information: * New vehicle with manufacturer's warranty * Subject to change and prior sale ----Delivery time: * Available from calendar week 22/2026

Condition: used, axle configuration: 2 axles, first registration: 06/1998, loading space length: 4,300 mm, loading space width: 2,400 mm, loading space height: 850 mm, 2-axle BlomenRöhr Platform Trailer SDAH 8.5T First registration: 06/1998 Hnjdpjv Ridhefx Aaask Manufacturer: BlomenRöhr Leaf suspension Tyres: 215/75 R17 Length: 6240 mm / Height: 2360 mm No MOT (TÜV) Further special equipment, data, or images available upon request! Details provided without guarantee/errors excepted! Information given online is non-binding and does not constitute guaranteed features. The seller is not liable for errors, input mistakes, or data transmission errors. Subject to change. Continuous purchase and sale as well as trade-in and rental of municipal technology / disposal and cleaning vehicles for sewer cleaning, wet and hazardous goods disposal.

Condition: used, overall weight: 2,000 kg, first registration: 08/1995, Trailer with frame for advertising banners or for transporting goods Hodpfxoynvdms Aaajnk Location: Im Erlenkamp 15

Condition: new, maximum load weight: 10,950 kg, overall weight: 14,400 kg, axle configuration: 2 axles, loading space length: 6,270 mm, loading space width: 2,470 mm, Year of construction: 2026, Equipment: ABS, tail-lift, Müller-Mitteltal ETÜ-TA-R 14.4 Tandem | Low Loader | Flatbed | Trailer Available immediately | Reference number for inquiries: 11611 | Delivery to your address possible * We are happy to offer you an individual quote * ---- * Gross weight: 14.4 t, Payload: 10.95 t * LED lighting system * GIGANT axles, EBS, twin tires 235/75R 17.5, parabolic springs * Tire pressure monitoring system (TPMS) * 6.27m x 2.47m flatbed with galvanized 400 mm front wall * Digger bucket support made of hardwood, bolted to the front wall * Platform height unladen: 930 mm / laden: 870 mm * One-piece ramps with hot-dip galvanized anti-slip grating, telescopic down to approx. 20 mm, secured with support bars and inclined bracing * Ramp assist with vertically mounted, adjustable springs for easy single-person operation * 4 UVV drop lashing rings (LC 6300 daN) * Perforated outer frame (45°-bent with perforation for lashings, lashing capacity per point LC 2000 daN at least 480 mm apart. Installation of drop lashing rings LC 3000 daN at approx. 600 mm spacing possible) with close-spaced transverse profiling, high-profile front and rear ends, rear loading ramp, hot-dip galvanized * 10 UVV lashing rings LC 3000 daN recessed in existing grid in the outer frame, additionally * Further lashing options via boreholes (Ø 50 mm, LC 1200 daN) in the front and rear crossmembers * Tool box in front of the front wall * Side marker lights with indicator function * 50 mm thick softwood floor, chassis hot-dip galvanized * Height-adjustable landing gear at the front, foldable supports at the rear * Retrofitting of 2 container twistlocks possible * Drawbar with 40 mm draw eye (hot-dip galvanized), height adjustable, 50 mm eye available on request * 1 removable LED marker lamp at the rear ---- * Leasing, hire purchase, financing, trade-in possible * e.g. from 510 euros over 60 months, no down payment, no residual value * ---- * Our opening hours: * Monday - Thursday: 08:00 - 17:00 * Friday: 08:00 - 15:00 Hodeyndh Hjpfx Aaaonk Outside of opening hours we are available by appointment We speak German, English, Polish, and French Leasing, financing, and trade-in possible

Condition: new, maximum load weight: 20,500 kg, overall weight: 27,000 kg, axle configuration: 3 axles, loading space length: 7,000 mm, loading space width: 2,470 mm, Year of construction: 2026, * ETÜ-TR 27.0 Platform: * EBS (Electronic Braking System) * Emergency release device for spring-loaded cylinders * Drum brakes * 3 x 9 t BPW Eco axles * Air suspension with lift and lower system featuring RTR function * First axle liftable * Last axle as trailing steering axle with electro-pneumatic locking via reverse gear PIN (locking of the trailing axle from the tractor unit for maneuvering purposes – no truck-side installation required – assigned to PIN 10 in the 15-pin connector, for maneuvering purposes only, not for public road use) Hsdpfer Dpzxsx Aaaenk * SmartBoard control box as infotool with pressure sensors for total axle load display * Tire pressure monitoring with display option in the truck via EBS signal (no truck-side installation required) * Fixed central drawbar with 50 mm flange eye (loaded 900 mm, vertical adjustment at the head plate) * Mechanical landing gear at the front, mechanical swing-down supports at the rear of the chassis * Hydraulic flow divider * Continuous side walls (without central stanchion) up to the drive-on ramp * Folding rear stanchions * Steel rear wall inserted in front of the rear stanchions * Mechanically adjustable warning sign package at front and rear * Toolboxes made of galvanized sheet steel – black powder-coated – approx. 650 x 300 x 600 mm, right side * 15-pin electric connector * LED tail lights * Removable LED beacon, incl. bracket and installation * 2 x LED reverse lights at the rear of the vehicle (switched via reverse gear) * Flashing LED side marker lights * 60 mm larch / Douglas fir wooden floor * 400 mm slotted steel front wall * Perforated outer frame approx. 45° angled with devices to mount 3 t folding lashing rings * In each corner 1 x 10 t lashing ring, plus on each side 2 x 10 t and 3 x 6.3 t lashing rings * Various holes in the front and rear cross members for 1.2 t lashing options * Hydraulic one-piece loading ramps approx. 3,000 x 720 mm, mechanically adjustable sideways * 4-section hydraulic control block for possible retrofitting of hydraulic ramp shift * Chassis, drawbar, front wall, mechanical rear supports, loading ramps hot-dip galvanized * Axles, air tanks, flange drawbar eye and front landing gear painted in black * Hydraulic flow divider in the trailer (for hydraulic pump output in the truck from over 40 l/min up to 120 l/min) * New vehicle with manufacturer warranty * Errors and prior sale reserved * Available from CW 13/2026 * Sample images (Pictures may differ from the actual vehicle due to special equipment)

Condition: new, maximum load weight: 16,400 kg, overall weight: 30,000 kg, axle configuration: 3 axles, Year of construction: 2024, * T3 Profile 30.0: * EBS-E (electronic braking system) * TPMS (tire pressure monitoring system) * Emergency release device for spring-actuated cylinders * Drum brakes * 3 x 11 t BPW Eco axles * Air suspension with lift and lowering system * SmartBoard as an information tool on the trailer with pressure sensors to display total axle load per axle group * Side underrun protection * Mechanically adjustable warning sign packages, front and rear * Front axle closed plastic mudguards and rear axle straight galvanized steel splash guards, each with spray protection * Hinged lid (hot-dip galvanized) for the toolbox located on the turntable platform * Toolbox made of approx. 650 x 300 x 600 mm galvanized steel (black powder-coated), mounted on the right side * 15-pin power connector * LED lighting 12 / 24 V * Removable LED beacon at rear * Side marker lights with indicator control * Tow bar with 40 mm drawbar eye and height adjustment via draw spring & turnbuckle * Tire pressure monitoring system with indication in the truck via EBS signal (no truck-side installation required) * Rubber coating on the folding ramps and on the approach slope, left and right (approx. 860 mm long) * Rubber coating on longitudinal beams from front bulkhead to rear crossmember * Hardwood flooring on the running surfaces of the low-loader platform * Four stake pockets per side, each with 2 t lashing option * Load securing package consisting of: 5 pairs of UVV lashing rings, swivel and retractable, loadable in all directions and recessed in the outer frame – 13.4 t in the corners, otherwise 10 t * 6 pairs of mechanical swing-out extensions for 3 m total width (not available on the rear slope) * Board holder mounted longitudinally below the loading area * Roller stop raised in front of bulkhead, with one 6.4 t lashing ring per side * Hydraulic folding ramps (approx. 4,650 x 720 mm) with hydraulically extendable ramp tip and load-holding valves * Hydraulic lateral ramp displacement * Rear support hydraulically operated (single-stage cylinder) * Hydraulic flow divider in the trailer (for hydraulic pump output in truck from over 40 l/min up to max. 140 l/min) * Hydraulic control block splash-proof * Dual-circuit hydraulic system Hodpfx Aeq Dyvcoaaenk * Loading area above turntable: approx. 1,960 x 2,520 mm * Rear loading area: approx. 6,500 x 2,520 mm (including 860 mm approach slope) * Loaded deck height approx. 890 mm +/- 20 mm (air suspension) * Chassis, turntable, roller stop, swing-out wideners and loading ramps hot-dip galvanized * Axles, turntable, drawbar, air reservoirs etc. painted in black * Loaded deck height: approx. 890 mm +/- 20 mm * New vehicle with manufacturer's warranty * Subject to errors and prior sale * Available from week 20/2026

Condition: new, maximum load weight: 10,900 kg, overall weight: 14,400 kg, axle configuration: 2 axles, loading space length: 6,270 mm, loading space width: 2,470 mm, loading space height: 400 mm, Year of construction: 2025, ETÜ-TA-R 14.4 ----Braking system: * EBS electronic braking system * Emergency release mechanism for spring brake cylinders * Drum brakes ----Axles: * 2 x 7 t Gigant axles ----Suspension: * Air suspension ----Tow bar / Flange eye: * Tow bar height-adjustable by 300 mm * Tow bar extension by 250 mm to 2,250 mm * 40 mm flange towing eye ----Lighting / Electrics: * RDÜ (tyre pressure monitoring system) * LED tail lights 12 / 24 V * 15-pin power connector ----General attachments: * Jost landing gear front * Externally mounted, hot-dip galvanized folding supports at rear * Plastic toolbox, front right, mounted on the bulkhead * Side underrun protection * Plastic quarter mudguards ----Low loader platform: * 50 mm softwood floor * Fittings in front of bulkhead for retrofitting container locks * Bolted flat sheet steel bulkhead Hedsq Dyvyopfx Aaajnk * Drop sides made of trapezoidal-profiled steel sheet, folding with drop side lifting springs * Rear steel wall retractable between ramp holders, stowable in front of bulkhead when not in use * Bolted rear stanchions * Rear drive-on slope approx. 860 mm ----Load securing: * Perforated outer frame, approx. 45° angled, with 2 t lashing force every 480 mm * Option to install 3 t folding lashing brackets every 600 mm * 1 x 6.3 t lashing ring in each front and rear corner * Various drillings for 1.2 t lashing points in front bulkhead and rear end crossmember ----Ramps: * One-piece, mechanical mesh ramps with spring assist for single-person operation, approx. 2,750 x 600 mm (collapsible to 20 mm) ----Paintwork: * Hot-dip galvanized chassis as well as tow bar, bulkhead, tailgate, and access ramps * Sideboard colour in RAL 9010 pure white * Painting of side walls in alternative RAL colours available at extra cost ----Info: * --Reinforced and certified body built according to EN 12642 XL including load securing certificate-- * New vehicle with manufacturer’s warranty * Subject to errors and prior sale ----Delivery time: * Available immediately ex Egestorf

Condition: new, maximum load weight: 37,390 kg, overall weight: 48,000 kg, axle configuration: 3 axles, Year of construction: 2026, * TS 3 RM ML 30.0: ----Brakes: * Wabco EBS-E (electronic braking system) * Emergency release system for spring brake cylinders * Drum brakes ----Axles: * 3 x 11 t BPW axles * Start-up aid for maneuvering purposes engaged on the first axle via EBS (without truck-side installation) * Rear axle as trailing steering axle with electro-pneumatic steering lock * Locking of the trailing axle for maneuvering purposes via EBS from the driver's cab (without truck-side installation) ----Suspension: * Air suspension with lifting and lowering device as well as Ride-on-Road (RtR) valve ----Electrics / Lighting: * Smart-Board infotool mounted on the trailer, equipped with pressure sensors for total axle load display * 15-pin power connector * LED lighting 12 / 24 V * Removable rear LED beacon Hjdpfx Asq Euakoaaonk * 2 additional LED reversing lights * 7-pin socket on the rear side for overlength lighting * Side marker lights with indicator control * Tire pressure monitoring with in-cab display via EBS signal (without truck-side installation) ----General Attachments: * Side underrun protection * Support winches at the front and swivel supports at the rear on the chassis * Straight steel mudguards * Spare wheel holder in front of the bulkhead cross member (without spare wheel) * Mechanically adjustable warning sign sets at the front and rear * Swivel arm as carrier for connection lines from truck to semi-trailer ----Low Loader Deck: * 2nd king pin position * Fifth wheel platform with front corners chamfered at 45° and front toolbox made of galvanized, powder-coated sheet steel, W = 2,480 x H = 500 x L = 665 mm with folding lid * 400 mm high drop-side aluminum boards (RAL color of choice) on the sides of the fifth wheel platform, foldable and removable * Rear board inserted 150 mm high * Rear slope on the fifth wheel platform leading to the drop deck approximately 700 mm long with chequer plate covering, and at the end, a perforated strip for attaching aluminum loading ramps * Fifth wheel platform with 50 mm clamped timber planks and drop deck platform with 60 mm clamped timber planks * Chequer plate above the axles * 9 mechanical folding deck wideners up to 3 m overall width, except on the rear slope (widening planks included, stored in a transverse compartment underneath the loading area) * 3 mounting recesses under the fifth wheel platform for storing either aluminum loading ramps or timber planks for wheel recess covers ----Load Securing (LaSi Package): Fifth Wheel Platform: * Perforated outer frame, angled 45°, with hole pattern for lashings (2 t lashing capacity per lashing point at a minimum spacing of 480 mm) * 3 x 13.4 t recessed lashing rings per side in the floor (1 x on the fifth wheel platform, 1 x on the longitudinal members after the step, and 1 x above the middle axle next to the longitudinal member) Drop Deck Platform: * 3 x 13.4 t lashing rings per side on outer frame (1 x at the start of the fifth wheel platform step, 1 x at the start of the access slope, 1 x at the end of the access slope) * 2 x 10 t lashing rings per side (1 x between front wheel recess and 1st axle, 1 x between 2nd and 3rd axle) * 3 x 5 t lashing rings per side, bolted to the outer frames of the wheel recesses (2 at the front and 1 at the rear wheel recess) ----Excavator Arm Rest: * Extended excavator arm rest from the end of the last rigid axle, over the steering axle, up to the end crossmember, continuous with internal reinforcement profile approx. W = 770 mm x rear d

Condition: new, maximum load weight: 23,500 kg, overall weight: 30,000 kg, axle configuration: 3 axles, Year of construction: 2026, Equipment: ABS, * T 3: * ABS brake system * Emergency release device for spring-actuated cylinders * Drum brakes * 3 x 11 t BPW Eco axles * Parabolic springs * Mechanical axle load equalizer at the rear * Lateral underrun protection * Swivel supports at the rear of the chassis frame * Mechanically adjustable warning sign packages front & rear * VA closed plastic mudguards as well as HA straight galvanized steel skirts with splash protection * Reflective contour tape on the sides and rear * Folding cover (hot-dip galvanized) for the toolbox in the turntable platform * Toolbox made of galvanized sheet steel approx. 650 x 300 x 600 mm – black powder-coated – mounted laterally under the chassis * 15-pin electrical connector * LED lighting 12 / 24 V * LED beacon (removable) at the rear * Drawbar with 40 mm towing eye and height adjustment via tension spring & turnbuckle Hsdpeq Dyv Iofx Aaasnk * Four stake pockets on each side (stakes not included), with lashing points * Load securing package consisting of: 2 lashing eyes (6.4 t) at the front left & right on the main frame of the turntable platform * 5 pairs of UVV lashing rings, swiveling and retractable * Loadable in all directions and integrated into the outer frame: 13.4 t in the corners, otherwise 10 t * 6 pairs of mechanical folding outriggers for 3 m total width (not in the rear slope) * Widening planks stored under the loading area in a storage compartment * Excavator arm rest across the rear axle up to the rear cross beam, approx. 2,100 mm long (2 pairs of 6.4 t lashing rings at the sides of the excavator arm rest) * Hydraulic folding ramps (approx. 4,650 x 720 mm) with hydraulically extendable tip and load-holding valves, hydraulic lateral ramp shift * Hydraulic flow divider in the trailer (for hydraulic pump output in the truck over 40 l/min up to max. 140 l/min), dual-circuit hydraulics * Loading area above turntable: approx. 1,960 x 2,520 mm * Rear loading area: approx. 6,500 x 2,520 mm (incl. 860 mm approach slope) * Loading height when loaded approx. 860 mm +/- 30 mm with leveling unit * Chassis, turntable, folding outriggers, drop-down supports at the rear and drive-on ramps hot-dip galvanized * Axles, springs, drawbar, air tanks etc. painted black * New vehicle with manufacturer’s warranty * Subject to errors and prior sale * Available from week 19/2026

Condition: new, maximum load weight: 23,500 kg, overall weight: 30,000 kg, axle configuration: 3 axles, loading space length: 8,380 mm, loading space width: 2,520 mm, Year of construction: 2026, * PT 30 Profile: * EBS (electronic braking system) * Emergency release device for spring brake cylinders * Drum brakes * 3 x 11 t Gigant axles * Air suspension with lift and lowering feature as well as RtR-valve * Smart-Board mounted on the trailer as an infotool (for axle load display – front and rear display separated) * Tire pressure monitoring with display functionality in the truck via EBS signal, no truck-side installation required * Side underrun protection * Swivel supports at the rear of the chassis frame * Mechanically adjustable warning sign packs at the front and rear * Front axle plastic quarter mudguards with splash protection * Rear axle straight galvanized steel plate skirts with splash protection * Reflective contour tape on the sides and rear Hnedpfx Aaotplwisaok * 15-pin power connector * LED lighting 12 / 24 V * Rear LED rotary beacon (removable) * 1,200 mm long drawbar with 40 mm towing eye and height adjustment via draw spring & turnbuckle * Tool box made of galvanized sheet steel approx. 650 x 300 x 600 mm, black powder-coated, mounted on the right side * Accessory box in the bogie frame with folding lid, 2 fixed container locks (directly after the bogie platform) * ROBOT welded anti-slip coating on the bogie platform steel plate (protruding welding seams) * Load securing package consisting of: 2 lashing eyes (13.4 t) front left & right on the front wall bracket, 1 pair each front & rear UVV lashing rings (13.4 t), and 3 pairs each side UVV lashing rings (10 t), swiveling and lowerable, loadable in all directions and recessed in the outer frame, 3 stake pockets each side with simultaneous 2 t lashing provision * 6 pairs of mechanical folding outriggers for 3 m overall width (not in the rear slope) * Widening planks stored in the center of the load floor * Hydraulic one-piece drive-on ramps approx. 3,000 x 720 mm * Mechanically adjustable sideways * 4-way control block for later retrofit of hydraulic ramp shift * Continuous excavator arm rest above the rear axle up to the end cross member (total length approx. 2,100 mm) * 2 pairs of lashing eyes LC 6,400 daN in the excavator arm rest, laterally in the longitudinal frame * 2 galvanized steps on the bogie left & right * Profifix lashing rail in the longitudinal axis center, in flush area for lashing capability up to LC 3,000 daN * Chassis, bogie, folding outriggers, drop supports, and ramps hot-dip galvanized * Axles, slewing ring, air tank, and drawbar painted black * Load edge (loaded) approx. 910 mm +/- 20 mm with air suspension * New vehicle with manufacturer’s warranty * Errors and prior sale excepted * Available from approx. CW 22/2026 * Sample images

Condition: new, maximum load weight: 14,660 kg, overall weight: 18,000 kg, axle configuration: 2 axles, loading space length: 6,270 mm, loading space width: 2,470 mm, loading space height: 400 mm, Year of construction: 2026, * ETÜ-TA-R 19.0: * Wabco EBS brake system * RDÜ tire monitoring system * Emergency release device for spring brake cylinders * Drum brakes * 2 x 10-ton BPW Eco axles * Parabolic springs -110 mm wide- with tandem equalizer * Drawbar with 50 mm flange eye and height-adjustable drawbar * Jost landing gear at the front * Exterior folding supports at the rear * Lateral underrun protection * Plastic quarter mudguards * 15-pin electrical connector * LED tail lights * 50 mm softwood floor * Fixture in front of the bulkhead for optional retrofitting of container locks * Bolted smooth sheet steel front wall * Side walls made of steel sheet - trapezoidal profiled, foldable with drop-side spring assist * Steel rear wall, insertable between the ramps - bracket for storage inside at the front wall when not in use * Bolt-on rear stanchions * Perforated outer frame, approx. 45 degrees angled, with 2-ton lashing capacity every 480 mm * Optional installation of 3-ton retractable lashing rings every 600 mm Hsdpfx Aol Th Hwsaaenk * 1 x 10-ton lashing ring in each of the front and rear corners, various bores in the front and rear crossmembers for additional 1.2-ton lashing options * Profifix lashing rail longitudinally centered, for lashing capacity up to LC 3000 daN * One-piece mechanical grating ramps with spring assist for single-person operation, approx. 2,750 x 620 mm (collapsible to 20 mm) * Rear approach angle approx. 860 mm * Chassis, drawbar, front wall, rear wall, ramps, and folding supports hot-dip galvanized * Drop sides painted in RAL 9010 pure white * Optional painting of side panels in an RAL color for an extra charge * Axles, springs, air tank, flange eye, and landing gear painted in black * New vehicle with full manufacturer's warranty * Subject to errors and prior sale * Available approx. from week 21/2026 * Sample images

Condition: new, maximum load weight: 23,830 kg, overall weight: 30,000 kg, axle configuration: 3 axles, loading space length: 8,460 mm, loading space width: 2,520 mm, Year of construction: 2026, * T3 Profile 30.0: * EBS braking system * TPMS tire pressure monitoring * Emergency release device for spring brake cylinders * Drum brakes * 3 x 11 t BPW Eco axles * Parabolic springs * Mechanical rear axle equalization * Lateral underrun protection * Swing-down supports at the rear of the chassis frame * Mechanically adjustable warning panel kits at front and rear Hsdjl Thxdjpfx Aaajnk * Front: closed plastic mudguards, rear: straight, galvanized steel skirts, each with spray protection * Reflective contour marking tape on sides and rear * Hinged lid (hot-dip galvanized) for toolbox in the bogie platform * Multi-voltage system * LED tail lights * Removable revolving beacon at rear * Drawbar with 40 mm towing eye and height adjustment via tension spring & turnbuckle * 15-pin electrical connector * Four stake pockets each side (stakes not included), can also be used as lashing points * Load securing package consisting of: 2 lashing eyes (6.4 t) front left & right on the main frame of the bogie platform, 5 pairs of UVV-compliant folding and lowering lashing rings, loadable in all directions and recessed in the outer frame – in the corners 13.4 t, otherwise 10 t * 6 pairs of mechanical folding outriggers for 3 m total width (not in the rear taper) * Widening boards stored in the center of the loading area * Excavator stick trough over rear axle up to end cross member, approx. 2,100 mm long (2 pairs of 6.4 t lashing rings on the sides of the excavator stick trough) * Hydraulically operated one-piece access ramps (approx. 3,000 x 720 mm) * 4-section control valve for future retrofitting of hydraulic ramp shift * Mechanical lateral ramp shifting * Load area above slewing ring: approx. 1,960 x 2,520 mm * Unladen loading height approx. 1,070 mm * Rear load area: approx. 6,500 x 2,520 mm * Unladen loading height approx. 910 mm (incl. 860 mm approach slope) * Chassis, bogie, drawbar and ramps hot-dip galvanized * Axles, springs, air tanks etc. painted in black * 235/75 R 17.5 twin tires * 5,900 kg unladen weight * --Gross weight of 30,000 kg technically possible-- * Vehicle is hot-dip galvanized * New vehicle with manufacturer's warranty * Errors and intermediate sale excepted * Available from week 18/2026

Condition: new, maximum load weight: 17,650 kg, overall weight: 24,000 kg, axle configuration: 3 axles, loading space length: 9,230 mm, loading space width: 2,480 mm, Year of construction: 2026, * TP 30.0 with 3 cable drum supports ----Braking System: * Wabco TEBS (electronic braking system) * Emergency release mechanism for spring-loaded cylinders * Drum brakes ----Axles: * 3 x 11 t Gigant axles ----Suspension: * 17.5" air suspension with lift and lower system ----Drawbar: * Drawbar 1,800 mm long with 40 mm towing eye ----Electrics / Lighting: * Tire pressure monitoring with display option in the truck dashboard via EBS signal – no truck-side installation required * 15-pin electrical connector * 2 additional LED reversing lights (switched via reverse gear) * LED lighting ----General Attachments: * Aluminum air reservoir * Stainless steel toolbox, approx. 1,000 x 300 x 600 mm, mounted on the side * Side underrun protection * Plastic quarter mudguards * Rear underrun protection ----Platform: * Zurr-fix outer frame, 45° bent with hole pattern for securing equipment, lashing force per point 2,000 kg at a distance of 480 mm * Possible installation of 3,000 kg drop lashing brackets at approx. 600 mm interval – includes 12 pcs. 3,000 kg lashing brackets per side * 5 pockets per side for posts, 100 x 50 mm, in the outer frame – posts are not included in delivery * 30 mm phenolic plywood flooring ----Drum Supports: Hnedex Nli Nepfx Aaajk * 3 galvanized drum supports, secured via container locks, with side forklift pockets spaced 800 mm center/center (pocket width 185 mm) * Maximum drum diameter: 2,600 mm, maximum drum width: 1,650 mm * Clear distance between support arms approx. 1,775 mm, with cross brace * Max. drum weight per drum stand: 6,000 kg * Without drive and drum brake * Support arm with tension lock for securing the drum shaft * Steel drum shaft, 76 mm diameter, with centering and rotatable ends * 2 collar rings * 2 polyamide centering cones * 4 pcs. 3.2 t lashing eyes on the support arms for customer-provided securing of the drum against rotation and unwinding ----Loading Height: * Approx. 1,040 mm when loaded ----Paintwork: * Chassis, turntable, drawbar, outer frame and rear underrun protection hot-dip galvanized * Axles painted in black tone ----Info: * Technical upgrade to 30 t GVW possible * New vehicle with manufacturer's warranty * Errors and prior sale reserved ----Delivery Time: * Available from week 28 / 2026

Condition: new, maximum load weight: 18,900 kg, overall weight: 24,000 kg, axle configuration: 3 axles, loading space length: 7,000 mm, loading space width: 2,480 mm, Year of construction: 2026, * TRA-Kombi 24.0: ----Brakes: * Wabco EBS-E (electronic braking system) * Emergency release device for spring brake cylinders * Drum brakes ----Suspension: * Air suspension with manual lowering at the rear ----Axles: * 3 x 11 t Gigant axles * Center axle liftable ----Drawbar: * Pneumatically lowerable drawbar, 2,100 mm long with 40 mm towing eye & height adjustment device ----Electrics / Lighting: * LED tail lights * 15-pin electrical connector * TPMS (Tire Pressure Monitoring System) ----General Equipment: * Toolbox made of powder-coated steel sheet (W: 1,000 mm x H: 300 mm x D: 450 mm) * Storage box for container nets made of galvanized steel sheet (W: 960 mm x H: 300 mm x D: 450 mm) * Side underrun protection * Plastic quarter mudguards with splash protection * Plastic rear bump stops * Mechanical drop down stands at rear ----Container / Low Loader Deck: * Hot-dip galvanized main frame with raised outer frame (approx. 25 mm higher) to guide the roll-off containers * Steel sheet floor with roller recesses in the bogie area * For roll-off container transport, container length from 5,500 to 7,000 mm possible * Pneumatic 4-point clamp locking as well as mechanical plug-in stops at the front in the running rails * Load certificate according to DIN 30722-1 * Transportation of up to 2 skip containers with a maximum of 10 m³ volume possible * Includes 8 repositionable skip stops for lateral centering of skips, front 4 skip stops plug-in with pendulum-mounted stop ----Load securing: * 3 pairs of 10 t UVV lashing rings at the sides for attaching tensioning elements for positive and non-positive securing of the skips * 4 side lashing bars in cloverleaf design and 1 pair of 13.4 t UVV lashing rings at the front * Load securing certificate according to DIN EN 12195-1, DIN EN 12640, DIN EN 12642 and VDI 2700 Hnjdpfopk D Awox Aaaek ----Ramps: * Weld beads as anti-slip surface on the approach ramp running rail * 1 pair of aluminium approach ramps (16 t / pair), 2,800 x 400 mm, suitable for rubber-tyred and tracked vehicles (lockable storage compartment from the rear) ----Tyres: * Tyres: 235/75 R17.5 ----Ride height: * Loaded ride height approx. 1,003 mm ----Payload: * Payload 18,900 kg ----Paintwork: * Reflective contour tape on sides and rear * Axles, turntable, drawbar and air tank painted in black tone * Hot-dip galvanized main frame ----Info: * Technically permissible total weight of 27,000 kg possible * New vehicle, unregistered, with manufacturer warranty * Subject to prior sale and errors excepted ----Delivery time: * Available from week 20/2026

Condition: used, maximum load weight: 15,150 kg, overall weight: 18,000 kg, axle configuration: 2 axles, first registration: 10/1994, Platform for ballast weights 50 mm towing eye 4 lashing eyes Drum brake Hnjdpjw Sqilefx Aaaok Leaf spring suspension Support legs SAF axles All information is subject to change without notice. Subject to prior sale.

Condition: used, maximum load weight: 7,200 kg, overall weight: 9,000 kg, axle configuration: 1 axle, first registration: 03/2008, ? Platform for ballast weights ? 40 mm towing eye ? 9 lashing eyes ? Drum brake ? Leaf spring suspension ? Support legs ? BPW axles Hedpewfku Aefx Aaasnk All information is subject to change without notice. Subject to prior sale.

Condition: new, maximum load weight: 10,360 kg, overall weight: 14,400 kg, axle configuration: 2 axles, loading space length: 6,270 mm, loading space width: 2,470 mm, loading space height: 400 mm, Year of construction: 2025, * ETÜ-TA-ER 14.4: ----Brakes: * Electronic braking system (EBS) * Emergency release device for spring-loaded cylinders * Drum brakes ----Axles: * GIGANT axles ----Suspension: * Air suspension with lift and lowering system ----Drawbar / Flange drawbar eye: * Height-adjustable drawbar (adjustable by 300 mm) * 40 mm flange drawbar eye ----Electrics / Lighting: * TPMS (Tire Pressure Monitoring System with display option in the truck via EBS signal—no truck-side installation required) * LED lighting system * 15-pin power connector ----General attachments: * Jost landing gear at the front * Externally mounted, hot-dip galvanized folding support legs at the rear * Plastic toolbox mounted on the front wall, right-hand side * Side underrun protection * Plastic quarter mudguards ----Lowbed platform: * 50 mm softwood floor * Preparation for subsequent installation of 20" container locks at the front and rear * Bolted front wall, smooth sheet steel * Drop sides made of trapezoidal-profile sheet steel, foldable with sideboard spring assist * Bolted, hot-dip galvanized rear stakes Hnedpfxjpk D Dqj Aaajk ----Load securing: * Perforated outer frame, approx. 45° angled, with 2 t lashing capacity every 480 mm * Option to fit 3 t folding lashing rings every 600 mm * One 6.3 t lashing point at each front and rear corner * Various holes in the front wall and end crossmember for 1.2 t lashing options ----Ramps: * 1 pair of aluminum loading ramps approx. 3,310 x 400 mm (load capacity 8 t per pair), suitable for rubber-tired and tracked vehicles; storage compartment underneath the loading platform integrated in the chassis for rear access ----Paintwork: * Chassis, drawbar, front wall, and rear wall hot-dip galvanized * Entire vehicle hot-dip galvanized ----Info: * New vehicle with manufacturer's warranty * Errors and prior sale excepted ----Delivery time: * Immediately available ex Egestorf

Condition: new, maximum load weight: 10,800 kg, overall weight: 14,400 kg, axle configuration: 2 axles, loading space length: 6,270 mm, loading space width: 2,470 mm, Year of construction: 2026, * ETÜ-TA-R 14.4: ----Brakes: * EBS brake system * Emergency release device for spring brake cylinders * Drum brakes ----Axles: * 2 x 7 t Gigant axles ----Suspension: * Parabolic suspension with equalizing unit ----Drawbar / Flange Drawbar Eye: * Drawbar height-adjustable by 300 mm * Drawbar extension by 250 mm to a total length of 2,250 mm ----Electrics / Lighting: * Tire pressure monitoring with display functionality in the truck via EBS signal – no truck-side installation required * 15-pin power socket * LED lighting system 12 / 24 V * Multi-voltage EBS system for towing vehicles with 12 and 24 V electrics ----General Attachments: Hjdpfx Asrwc R Rsaaonk * Support winch at the front * Externally mounted folding supports at the rear * Plastic toolbox approx. 858 x 500 x 500 mm mounted front right on the bulkhead * Side underrun protection * Plastic quarter mudguards ----Low Loader Platform: * 50 mm softwood flooring * Provision in front of the bulkhead for retrofitting container locking devices * 400 mm bolt-on smooth steel bulkhead * Bolt-on rear stanchions * Drop sides with spring-assisted lift ----Load Securing: * Perforated outer frame, approx. 45° angled, with 2 t lashing capacity every 480 mm * Installation of 3 t folding lashing rings possible every 600 mm * 1 x 6.3 t lashing point in each front and rear corner * Various holes in the front and rear beams for 1.2 t lashing points * Profifix lashing rail centrally along the longitudinal axis for lashing capacity up to LC 3000 daN ----Ramps: * Single-piece hydraulic steel grate loading ramps, approx. 2,750 x 600 mm (can be collapsed to 20 mm) * Hydraulic flow divider in the trailer (for hydraulic pump performance in the truck from over 40 l/min up to a max. of 140 l/min) ----Paintwork: * Chassis, drawbar, bulkhead, mechanical drop supports, and loading ramps hot-dip galvanized * Axles, springs, air tank, front support winch, and flange drawbar eye painted in black * Drop sides painted RAL 9010 pure white * Painting of side walls in any RAL color available at extra charge ----Information: * New vehicle with manufacturer’s warranty * Subject to errors and prior sale ----Delivery time: * Available from approx. week 16/2026

Condition: used, maximum load weight: 31,000 kg, overall weight: 40,000 kg, axle configuration: > 3 axles, first registration: 07/2024, loading space length: 9,290 mm, loading space width: 2,520 mm, loading space height: 950 mm, * PT 40.0 profile: * Wabco EBS-E (electronic braking system) * Emergency release device for spring-loaded cylinders * Drum brakes * 4 x 11 tonne Gigant axles * Air suspension with lifting and lowering system and RtR valve * Manometer pressure indicator for determining load weight (axles separated into 2 air suspension circuits) * Side impact protection * Swivel supports at the rear of the chassis frame * Mechanically adjustable warning sign packages at the front and rear * Front plastic quarter fender with splash guard * Rear straight galvanized. Sheet steel aprons with splash guard * Reflective contour tape on the side and rear * EBS multi-voltage system with 12 & 24 V electrics * 15-pin power plug * LED lighting system 12 / 24 V * LED rotating beacon (removable) at the rear * 2 LED reversing lights (switched via reverse gear) * Pull scissors with 50 mm pull eye and height adjustment * Tool box made of galvanized sheet steel, black powder-coated, approx. 1,000 mm wide, 600 mm deep, 300 mm high * Front section in front of the bogie platform approx. 490 mm long with 45° corners * ROBOT welded ANTI-SLIP coating for the steel plate of the bogie platform * La-Si package consisting of: in front of the front wall support on the left & right 1 x 13.4 ton each. UVV lashing eye, 4 holes on each side in the bogie platform with a lashing force of 2 tons each, 1 pair of lashing eyes (13.4 tons) hanging at the rear left and right in front of the rear carrier, 4 pairs of UVV lashing rings (10 tons) on each side, can be swiveled and lowered, can be loaded in all directions and embedded in the outer frame, 3 stake pockets on each side with a simultaneous 2 ton lashing option * Hot-dip galvanized mechanical folding boom for a total width of 3 meters (but not in the rear slope) * Plank holder for widening under the chassis on the left in the longitudinal direction Hodol Tlhropfx Aaaenk * Excavator boom storage above the rear axle to the end carrier approx. 2,100 mm long and approx. 190 mm deep, 2 pairs of 6.4 tons on each side. Lashing rings in the excavator boom storage * Hardwood floor on the running surfaces of the low-loading platform * Hydraulic one-piece ramps (approx. 3,000 x 720 mm) mechanically laterally adjustable * Outer planks of the ramps made of hardwood * Steel construction in preparation for 6-way control slide * Loading edge unloaded approx. 950 mm +/+ 20 mm chassis * Bogie, folding boom, mechanical drop supports, ramps hot-dip galvanized * --Axles, air tank, pull scissors painted in a black tone-- * Tires 235/75 R 17.5 * Vehicle has a daily registration in 07/2024, due to missing tire pressure monitoring system and has not been loaded/used * New vehicle with manufacturer's warranty * Errors and prior sale subject to reservation * Available for immediate delivery from Egestorf

Condition: new, overall weight: 3,500 kg, loading space length: 6,200 mm, loading space width: 2,100 mm, tire size: 13, Year of construction: 2025, ANHÄNGERWIRTZ, the pick-up marketplace for your new trailer, offers top brand-name models! Over 850 new trailers in stock Over 130 used trailers constantly available. Non-binding example: Variant Machinery Transporter Variant Multi-transporter 3563 UX 620x210x30cm, 3800kg, braked tandem flatbed with low chassis, 13" wheels, tilting platform with manual hydraulic pump, 30cm foldable aluminium side walls, continuous 90cm high loading ramp with lifting aid, tie-down rings to DIN standard in chassis edge, automatic jockey wheel, modern LED lighting..... Hnsdpfx Aaoxcytgoaek Also available in various lengths and configurations. Our Trailershop offers you the unique Roadster at a fair price with short-term availability. New vehicle, invoice with VAT shown, warranty from a specialist dealer with 35 years of experience. Copyright on images, text, and logos 11.2025 VDK-3563UX30BLACK

Condition: new, maximum load weight: 31,630 kg, overall weight: 40,000 kg, axle configuration: > 3 axles, loading space length: 9,250 mm, loading space width: 2,520 mm, * T 4: * EBS (Electronic Braking System) * Emergency release device for spring brake cylinders * Drum brakes * 4 x 11 t Gigant axles * Parabolic springs Hnjdpfx Aaorczm Djajk * Mechanical axle equalization front and rear * Tire pressure monitoring with display functionality in the truck via EBS signal (no truck-side installation required) * Warning sign packages front & rear * Reflective contour markings on the sides and rear * EBS multi-voltage system for 12 & 24 V electrics * Removable LED beacon at rear * 24 V 15-pin power cable, additionally 12 V 7+4 pin power cable * Extended connection cables for agricultural and forestry tractors * LED lighting * Straight drawbar with 40 mm towing eye and infinitely adjustable height * Powder-coated steel toolbox and basket-type spare wheel holder mounted on the right side * Closed single plastic mudguard at the front * Straight rear steel spray suppression mudguards, including spray suppression * Side underrun protection * Extended offset bend, 500 mm forward * Turntable platform extension, 520 mm with 45° corners and 3 recessed, lockable storage compartments with lids * Chassis made of high-tensile fine-grain steel * Deck over turntable platform: 50 mm softwood, low-bed platform: 60 mm softwood * Outer boards of ramps: 50 mm bamboo * 4 stake pockets per side (stakes not included), double as 2 t lashing points * Load securing package includes: 2 lashing eyes (6.4 t) front left & right on main frame of turntable platform; 1 pair each side front & rear (13.4 t) lashing rings on outer frame; 4 pairs per side (10 t) swingable/drop-down multi-directional lashing rings inlet into outer frame; 2 pairs (6.4 t) on excavator arm support; 8 pairs galvanized folding widening brackets for up to 3 m overall width (not in rear slope) * Widening timbers stored in lateral compartment on left side * Excavator arm support above rear axle to end of drive-on slope approx. 2,300 x 740 x 190 mm * Mechanical rear drop-down support legs * Hydraulic, hot-dip galvanized ramps approx. 3,000 x 720 mm * Hydraulic lateral ramp shift via sliding tube on ramp shaft * Deck above turntable: approx. 2,990 x 2,520 mm * Rear loading area: approx. 6,280 x 2,520 mm * Loading height loaded: approx. 860 mm (including 860 mm drive-on slope) * Chassis, turntable, ramps, rear mechanical drop-down supports are hot-dip galvanized * Axles, springs, air tanks, and turntable painted in black * New vehicle with manufacturer’s warranty * Errors and prior sale excepted * Available from KW 21 / 2026

Condition: new, maximum load weight: 10,750 kg, overall weight: 14,400 kg, axle configuration: 2 axles, loading space length: 7,000 mm, loading space width: 2,470 mm, loading space height: 400 mm, Year of construction: 2025, * ETÜ-TA-R 14.4: ----Brake System: * EBS braking system * Emergency release device for spring brake cylinders * Drum brakes ----Axles: * 2 x 7 t Gigant axles ----Suspension: * Parabolic springs with equalizing unit ----Drawbar / Flange Eye: * Drawbar adjustable in height by 300 mm * Drawbar extension by 250 mm to 2,250 mm * 40 mm flange towing eye ----Electrical / Lighting: * RDÜ tire pressure monitoring * 15-pin electrical connector * LED lighting ----General Attachments: * Landing gear front * External folding supports, rear * Plastic toolbox approx. 858 x 500 x 500 mm, front right on the front wall * Side underrun protection * Plastic quarter mudguards ----Low-loader Platform: * 50 mm softwood flooring * Preparation in front of the bulkhead and rear slope for subsequent installation of container locks for transporting 20" containers * Bolted front wall made of smooth sheet metal * Fold-down side walls made of trapezoidal steel sheet, split once in the middle * Removable steel rear wall, can be stowed inside at the front wall when not in use (between ramp holders) * Bolted rear stanchions ----Load Securing: * Perforated outer frame, approx. 45 degrees angled, with 2 t lashing force every 480 mm * Option to install 3 t drop lashing brackets every 600 mm * 1 x 6.3 t lashing ring at each front and rear corner * Various holes in the front and rear crossbeam for 1.2 t lashing options ----Ramps: * One-piece mechanical grid ramps with spring assistance for single-person operation, approx. 2,750 x 600 mm (can be collapsed to 20 mm) * Approach ramp at rear approx. 860 mm chassis ----Wheelbase: * Wheelbase 1,140 ----Paintwork: * Drawbar, front wall, tailgate, folding supports and ramps hot-dip galvanized * Axles, springs, air tanks, flange towing eye and landing gear painted black * Side boards painted RAL 9010 pure white * Side walls available in custom RAL color at extra charge ----Information: * Reinforced and certified body according to EN 12642 XL, including load securing certificate * New vehicle with manufacturer's warranty * Subject to errors and prior sale ----Delivery time: Hnedpfjv Eq Evjx Aaajk * Available immediately from Egestorf on the A7