Used Lowbed Semitrailers for sale (377)

Condition: new, overall weight: 47,000 kg, axle configuration: 2 axles, Year of construction: 2026, Technical data MAX510-Z-2H-ATX-A-6.85-PA Speed: 80 km/h Total weight: 47,000 kg Fifth wheel load: 23,000 kg Axle load: 24,000 kg Gooseneck length: 3,750 mm Fifth wheel height loaded: 1,200 mm Steering radius to the rear: 2,300 mm Loading area length: 6,850 mm Extendable by: 5,500 mm Loading height with max. load: 350 mm Chassis length: 2,600 mm Loading height of rear chassis with max. load approx: 1,005 mm Suspension travel: -150/+450 mm Axle spacing: 1,360 mm Total width: 2,540 mm Total weight depends on fifth wheel load. Low bed: Low bed with external supports in extendable design "SUPER LOW" design, length approx. 6,850 mm. Low bed with solid hardwood floor approx. 40 mm thick and mechanical locking. The supply lines are protected in the extendable supports and automatically adjust to the respective low bed length. 5 pairs of lashing rings that can be folded outwards (LC 10,000 daN). 6 pairs of threaded blocks on the inner support for mounting screwable RUD rings. Rear chassis: Rear chassis with closed outer frame, checker plate covering and continuous prism excavator trough approx. 1,250/700 x 505 mm, open at the rear. 2 pairs of lashing rings that can be folded outwards (LC 10,000 daN). 1 pair of tension rings lying in the trough (LC 8,000 daN+5,300 daN). 2 pairs of stake pockets for 100 x 50 mm stakes in the outer frame Gooseneck: Gooseneck in SNT design to optimize the loading area length, length approx. 3,785 mm. Gooseneck can be raised/lowered hydraulically and removed. Technical fifth wheel load: 23,000 kg For tractor units: 4 x 2, 6 x 2 and 6 x 4 PENDEL-AXLE: "PENDEL-AXLE", all axles hydro-mechanically forcedly steered. Hose rupture valve on the axle compensation cylinder with automatic RESET function. Hydraulic cylinder with shut-off valves and pins for securing in raised position. Final painting of the axles with 2 layers of 2-component paint in a single color in "FAY-Gray-34-0260". Technical axle load: 12,000 kg Hydraulic axle compensation. Axle tool. Braking system: Braking system in accordance with EU regulations with EBS-E (2S2M) without connecting cables to the tractor unit. Electrical system: Electrical system in accordance with EU regulations, lighting 24 volts ASPÖCK-NORDIK (ASS3) ASPÖCK-UNIBOX on the front connection strip with 24N, 24S & 15-pin sockets. Connection in accordance with ISO. 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Steel construction: Steel construction made of high-strength fine-grain steels. Steel qualities: S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa) Paint: First-class and long-lasting corrosion protection of the standard shot-blasted welded frame guaranteed by a 2-component (2K) zinc dust primer. A high-quality 2-component (2K) top coat in a single color in RAL colors of your choice. Rear section metallized and painted in RAL 9010 (pure white). No metallic paint possible. Tires: Tires 245/70 R 17.5 3PMSF At the manufacturer's discretion. Load index (146/146F) Hedpfx Afoizu Nwsnjl Preparation for screw-on container positioning for 1x 20' or 1x 40' container on the outer supports. Without container locks. i i2" kingpins iA galvanized steel bulkhead, approx. 400 mm high. iA spare wheel with holder in front of the bulkhead. i2 brake shoes with holder on the bulkhead. iYellow-red air couplings on the galvanized connection strip at the front. Steering from the front and rear can be operated using a cable remote control via push buttons, with alignment control of the axles. (without insta

Condition: new, maximum load weight: 36,461 kg, overall weight: 49,500 kg, axle configuration: 3 axles, total width: 2,480 mm, total height: 860 mm, Year of construction: 2026, Technical Description Gooseneck: Gooseneck with rear bevel of approx. 750 mm x 10°. 3 pairs of lashing rings (LC 5,000 daN). 30 mm thick hardwood flooring. Loading Platform: Loading platform behind the gooseneck hydraulically liftable and lowerable, length approx. 2,800 mm, with rear bevel of approx. 1,000 mm x 8°. 6 pairs of outward-folding lashing rings (LC 5,000 daN). 2 pairs of outward-folding lashing rings (LC 10,000 daN). 1 pair of inward-folding lashing rings on the front central beam (LC 10,000 daN). Grating flooring C40/4 (point load 2.3 t on an area of 20 x 20 cm), over the axles with chequer plate covering. Two-Part Steel Ramps: One pair of galvanized, two-part steel ramps approx. 3,185 + 1,420 x 1,250 mm with grating flooring C40/5 (point load 8 t on an area of 20 x 20 cm). Ramp with hydraulically foldable ramp sections and hydraulic lifting system. Maximum load per pair: 40,000 kg In accordance with regulation 1230/2012/EU, ramps less than 300 mm in length do not count towards the vehicle length of 16,500 mm in driving position. Landing Legs: JOST landing legs (mechanical) with 2-speed gearbox for 24 t lifting capacity (50 t test load). Tyres: Tyres 235/75 R17.5 3PMSF as per manufacturer’s choice. TPMS: TPMS tyre pressure monitoring system as per ECE R 141. Data transmission to the tractor unit via the standardized EBS interface according to ISO 11992. For correct display, the tractor unit must be able to receive and display these data. Axles: BPW axles and suspension, 2 fixed axles, 1 self-steering trailing axle. Technical axle load: 12,000 kg Electromagnetic reverse lock, activated via reverse gear and manually. Air suspension with raise and lower valve. Axle tools included. Brake System: WABCO braking system compliant with EU regulations with EBS-E (2S2M), without connecting lines to the tractor unit. Electrical System: Electrical system compliant with EU regulations, LED lighting 24 Volt ASPÖCK-NORDIK (ASS3). All LED side marker lights flash with the indicator. ASPÖCK-UNIBOX on the front connector strip with 24N, 24S & 15-pin sockets. Connection according to ISO: 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Steel Structure: Steel frame made of high-strength fine-grain steels. Steel grades: – S355J2+N/S355MC (yield strength 355 MPa) – S690QL/S700MC (yield strength 690 MPa) Hsdpfxjw Dl Hwe Afnjl Tarp Structure: Tarp structure approx. 3,960 mm – Galvanized front wall with a tensioning mechanism for the sliding curtains. – “EDSCHA” roof, forward-sliding on aluminum roof rail profiles (bolted to front and rear walls). – 3 pairs of movable stanchions on the loading platform. – Body can be hydraulically widened at the rear by approx. 750 mm to the left and right. – Sliding roof with upward-swinging portal carrier. – Sliding tarp with 700 mm length reserve and tensioning straps at approx. 600 mm intervals. Height to top edge of structure approx. 3,960 mm (loaded). – Driving with open sliding roof is not permitted and will cause damage to the tarp. Painting: Entire steel structure is automatically shot-blasted after welding using a blasting wheel system. Second blasting treatment with corundum for optimal coating adhesion. Full metallizing of the entire chassis with ZINACOR 850 (85% zinc / 15% aluminum) for best corrosion protection. Top coat with 2 layers of 2K finish, single-color in a shade of your choice according to the RAL 841GL standard. Rear section metallized and coated in RAL 9010 (pure white). No metallic paint.

Condition: new, maximum load weight: 36,156 kg, overall weight: 45,000 kg, axle configuration: 3 axles, Year of construction: 2026, MAX200-N-3A-13.60-19.5-2.54 Technical data Speed: 80 km/h Total weight: 45,000 kg Fifth wheel load: 18,000 kg Axle load: 27,000 kg Empty weight (+/- 3%): 8,844 kg Payload approx.: 36,156 kg Hedpfx Aog Sk Tvofnol Loading area length: 13,600 mm Fifth wheel height loaded: 950->1,050 mm Rear steering radius: 2,300 mm Extendable by: 3,400 mm Axle spacing: 1,360/1,405 mm Total width: 2,540 mm Technical description Loading area: Loading area in extendable design with pneumatically operated locking. 2 pairs of lashing rings (LC 5,000 daN). 1 pair of lashing rings (LC 10,000 daN). 6 pairs of lashing rings that can be folded outwards (LC 5,000 daN). 2 pairs of lashing rings that can be folded outwards (LC 10,000 daN). Cut-outs in the outer frame of the loading area for hanging tensioning straps. (LC 2000 da N) Seat supports: JOST seat supports (mechanical) with 2-speed gearbox for 24t lifting load (50t test load). Axles: SAF axles: SAF axles CD, air-sprung, with disc brakes (377 mm), with lifting/lowering function. (ET 120). The self-steering axles with electro-magnetic reversing lock can be activated via reverse gear or manually. Axle tool. (± 80kg) Braking system: Braking system in accordance with EU regulations with EBS-E (2S2M) without connecting lines to the tractor unit. Steel construction: Steel construction made of high-strength fine-grain steels. Steel qualities: S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa) Paintwork: First-class and long-lasting corrosion protection of the standard shot-blasted welded frame guaranteed by a 2-component (2K) zinc dust primer. A high-quality 2-component (2K) top coat in a single color in RAL colors of your choice. Rear section metallized and painted in RAL 9010 (pure white). No metallic paint possible. Electrical system: Electrical system in accordance with EU regulations, lighting LED 24 Volt ASPÖCK-NORDIK (ASS3) ASPÖCK-UNIBOX on the front connection panel with sockets 24N, 24S & 15-pin. Connection in accordance with ISO. 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Accessories included Yellow-red air couplings on the galvanized front connection panel. 2 pieces of brake shoes with holder. 2" kingpin A galvanized steel bulkhead approx. 2200 mm high. (± 105kg) EN12642-XL Yellow reflector tape in accordance with EU regulations on the side, on the extension and at the rear of the trailer. European reflector signs (red-yellow) on the rear of the trailer. Loading area with approx. 38 mm thick hardwood floor. (± 320kg) 10 pairs of stake pockets for 100 x 50 mm stakes in the outer frame of the loading area. (± 30kg) 1 spare wheel holder under the loading area on the right in the direction of travel. Tires 435/50 R 19.5 as selected by the manufacturer. A mud flap ( ) on the rear of the trailer. Manual and description on USB stick. A bracket for a rotating beacon on the rear of the trailer. One bracket for a rotating beacon on the gooseneck and on the rear panel on the left and right the warning signs including a socket. An INOX toolbox across the loading area. (1000x400x2500) (± 135kg) 6 pairs of WADER container pockets in the loading area, for 1x20' container, 2 x 20' container or 1 x 40' container, an additional locking point is provided in the pull-out for a 45' container. (± 90kg) 4 pairs of WADER container locks. (± 60kg) 10 pairs of galvanized plug-in stanchions approx. 100 x 50 mm, 1,000 mm high. (± 220kg) 3 pairs of stanchion pocket strips, mounted across the loading area, for plug-in stanchion

Condition: new, maximum load weight: 44,000 kg, overall weight: 61,000 kg, axle configuration: 3 axles, Year of construction: 2026, Further information here: Hodpfev D Abtox Afnjl

Condition: new, overall weight: 49,500 kg, axle configuration: 3 axles, Year of construction: 2026, 3-axle MULTIMAX PLUS low-bed semi-trailer, air-suspended and hydraulically forced-steered axles. Technical Data MultiPLUS-Z-3L-UB-12AT-9.60-17.5-2.54-GR Speed: 80 km/h Legal Gross vehicle weight: 49,500 kg / 31,500 kg Fifth-wheel load: 18,000 kg Axle load: 31,500 kg / 31,500 kg Gooseneck length approx.: 3,900 mm Gooseneck width approx.: 2,480 mm King pin trailing radius (rearwards) approx.: 2,100 mm Saddle height loaded approx.: 1,205 mm Loading platform length approx.: 9,600 mm Extendable by approx.: ? Loading platform width approx.: 2,540 mm Loading height at max. load approx.: 890 mm Suspension travel approx.: -55/+145 mm Axle spacing: 1,360 mm Gross vehicle weight depending on fifth-wheel load: Yes Special permit is required for exceeding country-specific regulations. Technical Description Gooseneck: Gooseneck in SNT Design for optimized loading platform length, length approx. 3,900 mm, rear with chamfer approx. 1,000 mm x 6°. Technical fifth-wheel load: 18,000 kg. For tractor units: 4 x 2 and 6 x 2. Loading platform: Loading platform, length approx. 9,600 mm with rear chamfer approx. 900 mm x 6°. Loading platform behind the gooseneck hydraulically raisable and lowerable, length approx. 3,000 mm, loadable up to approx. 9,000 kg. Ramps: DR-10-900-4920-GR-HV-AXS A pair of two-part AXS steel ramps approx. 4,920 mm long and approx. 900 mm wide. Open grating surface. Hydraulically folding ramp tips. Ramps can be hydraulically shifted individually by approx. 235 mm outwards and approx. 365 mm inwards. Maximum load capacity and approach angle per technical data sheet: C470319 Maximum ramp angle with lowered loading platform: 9° Axles and Suspension: BPW axles and suspension, all axles hydro-mechanically forced-steered. Technical axle load: 12,000 kg Air suspension with lift/lower valve. Axle tool kit. Tyres: 235/75 R 17.5 3PMSF twin tyres. Manufacturer of our choice Load index 143/141J (144/144F) Braking system: WABCO EBS-E braking system according to EU regulations. Without connecting cable to tractor unit. Lighting system: 24-volt lighting system in "ASPÖCK-NORDIK full LED" version as per EU regulations. (ASS 3) Metalizing: Complete HRM metalizing (High Resistance Metallisation) Complete steel structure shot blasted, then hot-finished with ZINACOR 850 (Zinc 85% - Aluminium 15%). Painting 6K final treatment: Complete steel structure shot blasted after welding. 1 coat zinc-based primer, 1 coat bonding primer. Final painting with 2 coats 2K (acrylic) single-colour in RAL shades of your choice, then cavity sealing with special wax. Rims in silver. Multi-colour and special painting at extra cost. Steel construction: Steel structure made of high-strength fine-grained steels. Steel grades: S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa) Hsdpfx Asizu Ntjfnel Welders certified to DIN-EN 287-1. MAG welding process to EN ISO 4063. Protective gas M21 per EN ISO 14175 Front wall of steel, plug-in, approx. 400 mm high Connection board for supply lines to the tractor unit at the height of the outer frame profile. ASPÖCK-UNIBOX at the front plug connection board with sockets 24N, 24S & 15-pin. 24N connection according to ISO-1185 24S connection according to ISO-3731 15-pin connection according to ISO-12098 If your pin configuration deviates from the ISO standard, please inform us. “Anderson” socket at the front connection board. Rema 78051-00 & Amp. 150 V. Cable for supply to electro-hydraulic unit and/or electric winch (35 mm²,

Condition: new, maximum load weight: 34,104 kg, overall weight: 47,000 kg, axle configuration: 2 axles, Year of construction: 2026, Further information here: Hjdpfxev D Abgj Afnel

Condition: new, maximum load weight: 40,017 kg, overall weight: 50,960 kg, axle configuration: > 3 axles, Year of construction: 2026, Technical Description Gooseneck: Gooseneck with rear chamfer of approx. 750 mm x 10°. 3 pairs of lashing rings (LC 5,000 daN). 30 mm hardwood flooring. Loading Platform: 5 pairs of folding external lashing rings (LC 5,000 daN). 3 pairs of folding external lashing rings (LC 10,000 daN). 1 pair of flat-mounted lashing rings at the front of the loading platform (LC 10,000 daN). Approx. 48 mm thick hardwood flooring, checker plate covering over the axles. Landing Legs: JOST landing legs (mechanical) with 2-speed gearbox for 24 t lifting capacity (50 t test load). Tyres: 205/65 R17.5 tyres as per manufacturer's specification. TPMS: TPMS tyre pressure monitoring system compliant with ECE R 141. Data transmission to the tractor unit via the standardised EBS interface according to ISO 11992. To ensure correct display, the tractor unit must be capable of transmitting and displaying this data. Axles: BPW axles, two fixed axles, two self-steering axles, air-suspended, with drum brake, with lifting/lowering function. The self-steering axles can be locked electronically via reverse gear or manually using an electromagnet. Axle tools included. Brake System: WABCO brake system in accordance with EU regulations with EBS-E (4S3M) without connecting lines to the tractor unit. Electrical System: Electrical system according to EU regulations, 24 volt LED lighting by ASPÖCK-NORDIK (ASS3). All LED side marker lamps flash with the turn indicators. ASPÖCK-UNIBOX at the front connection panel with 24N, 24S & 15-pin sockets. Connections conform to ISO standards: 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Steel Construction: Steel structure made from high-strength fine-grained steels. Steel grades: – S355J2+N/S355MC (yield strength 355 MPa) Hjdpfx Aow Dl Hqefnjl – S690QL/S700MC (yield strength 690 MPa) Paintwork: The entire steel structure is automatically shot-blasted with a turbine system after welding. A second abrasive blasting treatment with corundum ensures optimal adhesion of the coating system. HRM metallization of the entire vehicle chassis with ZINACOR 850 (85% zinc/15% aluminum) for superior corrosion protection. Final coating with 2 coats of 2K topcoat, single-colour in a shade of your choice according to the RAL 841GL system. Rear section metallized and painted in RAL 9010 (pure white). Metallic paint not possible. Paint system tested in salt spray test according to ISO 9227-NSS. Cavities sealed with special wax. Options included: 2" kingpin One galvanized steel bulkhead. Yellow-red air couplings on the galvanized front connection panel. 2 wheel chocks with holders on the bulkhead. Fixture at the rear of the gooseneck for ALU approach ramps. Further options upon request.

Condition: new, empty load weight: 12,000 kg, maximum load weight: 54,000 kg, overall weight: 66,000 kg, axle configuration: > 3 axles, loading space length: 9,300 mm, loading space width: 2,540 mm, loading space height: 860 mm, suspension: air, tire size: 245/70 R 17.5, color: grey, Equipment: ABS, Gooseneck: - Gooseneck with rear chamfer approx. 750 mm x 10° - 3 pairs of lashing rings (LC 5,000 daN) - 30 mm thick hardwood floor Extendable load platform: - Load platform in extendable design with rear chamfer approx. 1,000 mm x 8° - 5 pairs of fold-out lashing rings (LC 5,000 daN) - 3 pairs of fold-out lashing rings (LC 10,000 daN) - 1 pair of recessed lashing rings at the front of the deck (LC 10,000 daN) - Cut-outs in the outer frame of the loading area for attaching tie-down straps (LC 2,000 daN) - Hardwood floor approx. 48 mm thick, over the axles checker plate flooring Landing legs: - JOST landing gear (mechanical) with 2-speed gearbox for 24t lifting capacity (50t test load) Brake system: - WABCO brake system in accordance with EU regulations, with EBS-E (4S3M) Steel construction: - High-strength fine-grain steel construction Axles and tires: - BPW axles and suspension, 1st axle rigid, all other axles hydro-mechanically steered - Technical axle load: 12,000 kg - Air suspension with lift and lower valve - Axle service kit - TPMS tire pressure monitoring system as per ECE R 141 - Tires 245/70 R 17.5 3PMSF Hodpfx Asykpbkefnjl Included accessories: - 2" king pin - One galvanized steel front wall, approx. 400 mm high - Yellow-red air couplings on the galvanized connection rail at the front - 4 wheel chocks with holder at the front wall - One spare wheel with holder in front of the front wall - Electro-hydraulic power pack - Remote steering, operable from front and rear via cable remote with push buttons, with steering alignment indicator - European reflective signs (red-yellow) at the rear of the trailer - White reflective tape as per EU regulations on the sides and on the extension, rear in red - Holder for warning panels on both sides of the gooseneck and at the rear, including socket - Galvanized, extendable side extensions, extendable by approx. 230 mm per side - One beacon bracket at the rear of the trailer - Galvanized folding supports under the rear bevel of the deck - One mudflap at the rear of the trailer - Manual and documentation on USB stick - Central lubrication system BEKAMAX (Pico) with standard grease NLGI-2 and removable protective cover around the pump - Removable ALU side boards and rear board on the gooseneck, approx. 2,440 x 400 mm - Rear galvanized drop-in stanchions are removable (body length approx. 2,560 mm) - One INOX toolbox 1,350x400x400 mm on the gooseneck - Note: the box covers the oil filler plug - 4 pairs of WADER container locks in the deck for 1x 20ft, 2x 20ft, 1x 40ft, or 1x 45ft container - 7 pairs of pockets for drop-in posts 100 x 50 mm in the outer frame of the load platform - Adjustable hanging rail for ALU loading ramps at the rear of the vehicle - Square anti-slip strips 20 x 20 mm every 200 mm on the outer frame of the deck slope - Lift axle on the front axle controlled by TEBS-E depending on the actual axle load and loading condition - Four extendable warning signs, approx. 400 mm each, approx. 423 x 423 mm with position lamp - Mounting bracket for beacon on warning signs - Radio remote control for remote steering, in addition to cable control, with indicator LEDs on receiver for tracking alignment - Coated sand layer on checker plate surfaces on the gooseneck and deck as slip protection - 80 km/h speed stickers at rear and both sides - Load gauges for determining axle loads, including load chart

Condition: new, empty load weight: 10,700 kg, maximum load weight: 38,800 kg, overall weight: 49,500 kg, axle configuration: 3 axles, loading space length: 9,300 mm, loading space width: 2,540 mm, loading space height: 860 mm, suspension: air, tire size: 235/75 r 17,5, color: grey-black, Equipment: ABS, Gooseneck: •Gooseneck with bevelled corners at the front 45° and with a rear bevel of approx. 750 mm x 10° •3 pairs of lashing rings •Hardwood flooring 30 mm thick Loading area in extendable version: •Loading area in extendable version with rear bevel of approx. 1,000 mm x 8° •Cutouts in the outer frame of the loading area for hanging tensioning straps •Hardwood flooring approx. 48 mm thick, checkered sheet covering over the axles Two-part steel ramps: •One pair of galvanised, two-part steel ramps with approx. 48 mm thick hardwood flooring •Ramp with hydraulically foldable and unfoldable ramp parts, hydraulic lifting mechanism and hydraulically movable •Maximum load per pair: approx. 40,000 kg Axles and Tires: •BPW axles and suspension, 2 axles rigid, 1 axle with self-steering •Technical axle load: 12,000 kg •Electro-magnetic reversing lock can be activated via reverse gear and manually •Air suspension with lifting and lowering valve •Axle tool •235/75 R 17.5 3PMSF Brake system: •WABCO brake system in accordance with EU regulations with EBS-E Paintwork: •First-class and long-lasting corrosion protection of the standard shot-blasted welded frame guaranteed by a 2-component zinc dust primer •A high-quality 2-component top coat in one color in MB 7350 Nova gray •Rear section metallized and painted in RAL 9010 Seatposts: •JOST seatposts with 2-speed gearbox for 24t lifting load (50t test load). Steel construction: •Steel construction made of high-strength fine-grain steel •Steel qualities: •S355J2+N/S355MC •S690QL/S700MC Electrical system: •Electrical system in accordance with EU regulations, 24 volt lighting •ASPÖCK-UNIBOX on the front connection panel with 24N, 24S & 15-pin sockets Accessories included: •A spare wheel with holder •A galvanized steel bulkhead approx. 400 mm high •Yellow-red air couplings on the galvanized front connection panel •4 wheel chocks •A bracket for a rotating beacon at the rear of the trailer •Mounting in the rear area of the gooseneck for aluminum docking ramps •Galvanized folding supports under the bevel of the loading area •Cover plates to bridge the space between the ramps and the loading area •White Reflective tape in accordance with EU regulations on the side, on the extension and at the rear, red •Electro-hydraulic unit at the rear, under the loading area Hsdpfxjhlz S Ns Afnjl •A holder for the warning signs including a socket on the gooseneck and on the ramps on the left and right •Control valves for the ramps attached to the right-hand side of the trailer •ALU side walls and rear wall on the gooseneck, approx. 2,440 x 400 mm •The rear, galvanized plug-in stanchions are removable (length of the structure approx. 2,560 mm) •Four warning signs extendable by approx. 400 mm with a position light •3 pairs of WADER container pockets in the loading area for a 20ft, 30ft or 40ft container •6 pairs of stanchion pockets (100x50 mm) in the outer frame of the loading area •Galvanized extensions, extendable by approx. 230 mm each Page •Square climbing rails 20 x 20 mm every 200 mm on the outer frame of the loading area bevel •A painted layer of sand on the checker plates, above the kingpin and the loading area as anti-slip protection •Load pressure gauge for determining the axle loads including load diagram •HRM metallization (High Resistance Metallization) of the outer frame •Complete steel construction shot blasted, then the defined visible surfaces are hot-finished in metallization with ZINACOR 850 (zinc 85% - aluminum 15%)

Condition: new, empty load weight: 15,550 kg, maximum load weight: 47,450 kg, overall weight: 63,000 kg, axle configuration: 3 axles, loading space length: 8,800 mm, loading space width: 2,540 mm, loading space height: 860 mm, suspension: air, tire size: 235/75 R 17,5, color: grey, Equipment: ABS, Gooseneck: -Gooseneck in SNT design to optimize the loading area length, length approx. 3,700 mm -Rear gooseneck with bevel approx. 1,000 mm x 10° Loading area: -Loading area in extendable design, length approx. 8,800 mm, with bevel at the rear approx. 500 mm x 10° -One recess protruding into the loading surface and into the chamfer to accommodate the excavator dipper arm -Pneumatic locking with conical locking pins and reinforced locking positions -Hardwood covering on the bevel of the loading area Ramps: -1 Pair of two-part steel ramps with a length of approx. 4,350 mm and a width of approx. 900 mm -Ramps with hardwood decking -Hydraulically folding ramp tips -Ramps can be moved individually hydraulically by approx. 235 mm outwards and approx. 215 mm inwards -Square climbing ledges 20 x 30 mm, approx. every 200 mm on the outer frame of the ramp Axles and suspension: -BPW axles and suspension, 1st axle with preload steering, all other axles with forced hydromechanical steering -Technical axle load: 12,000 kg -1st axle with electromagnetic reverse lock via reverse gear and can be activated manually -Air suspension with lifting and lowering valve -235/75 R 17.5 twin tires -TPMS tire monitoring system in accordance with ECE R141 -TPMS tire monitoring sensors mounted in all wheels including spare wheels Accessories included: Hsdpek Aht Uefx Afnjl -steel front wall, pluggable, approx. 400 mm high -3 kW electro-hydraulic unit for controlling the hydraulic processes, with the exception of hydraulic cable winches -Parking position on the gooseneck for the warning signs when not in use -1 Spare wheel -On the gooseneck 1 pair of plug-in ALU side panels, approx. 400 mm high, anodized -One plug-in ALU rear panel on the gooseneck, approx. 400 mm high, anodized -Approx. 40 mm thick hardwood covering over the gooseneck, checker plate covering over the kingpin -2" kingpin -Guide plate from the gooseneck for the saddle plate, approx. 500 mm wide -4 wheel chocks -Mechanical seat posts with 2-speed gearbox and crank -JOST module B - static test load = 50,000 kg -1 Intermediate table, approx. 300 mm wide -Widenings (galvanized) extendable by approx. 230 mm per side -Wheel recesses with square climbing rails -ALU covers for the wheel recesses -1 pair of mechanical rear supports -Steering can be operated from the front and rear by cable remote control, with tracking control of the axles -1st axle with automatic lift axle function -Central lubrication system with 1 pump, BEKAMAX brand -Radio remote control for operating the self-steering, in addition to the cable remote control, with 2 indicator lights on the receiver as toe-in control -Wabco Smart Board System -4 warning signs, approx. 423 x 423 mm, extendable by approx. 400 mm, incl. 2 position lights and brackets for rotating beacon

Condition: new, empty load weight: 14,800 kg, maximum load weight: 61,700 kg, overall weight: 76,500 kg, axle configuration: > 3 axles, loading space length: 9,300 mm, loading space width: 2,540 mm, loading space height: 900 mm, tire size: 235/75/r17,5, color: grey, Equipment: ABS, Gooseneck: -gooseneck with rear bevel of approx. 750 mm x 10° -3 pairs of lashing rings -Hardwood decking 30 mm thick Loading area: -Loading area in extendable design with rear bevel of approx. 500 mm x 8° -9 pairs of lashing rings can be folded outwards -1 pair of lashing rings lying in the front of the cargo bed Cut-outs in the outer frame of the cargo bed for attaching lashing straps -Hardwood flooring approx. 48 mm thick, checker plate flooring over the axles Seat posts: -JOST fifth-wheel supports (mechanical) with 2-speed gearbox for 24 t lifting load (50 t test load) Axles and tires: -BPW axles and suspension, 1st axle self-steering, 2nd + 3rd axle rigid, 4th + 5th axle self-steering. -Technical axle load: 12,000 kg -1.4th and 5th axle with electro-magnetic reverse lock via reverse gear and manual activation -235/75 R 17.5 3PMSF tires Brake system: -WABCO brake system in accordance with EU regulations with EBS-E (4S3M) Paint finish: -First-class and long-lasting corrosion protection of the standard shot-peened welded frame guaranteed by a 2-component (2K) zinc dust primer A high-quality 2-component (2K) top coat in a single color in MB 7350 nova grey -Rear part metallized and painted in RAL 9010 (pure white) Steel construction: -steel construction made from high-strength fine-grained steels -Steel qualities: -S355J2+N/S355MC (yield strength 355MPa) -S690QL/S700MC (yield strength 690MPa) Accessories: -One spare wheel with holder in front of the bulkhead -2" kingpin -One galvanized steel bulkhead approx. 400 mm high -Yellow-red air couplings on the galvanized connection strip at the front -2 pieces of restraining shoes with holder on the bulkhead -Mounting in the rear area of the gooseneck for ALU docking ramps -Galvanized extensions, extendable by approx. 230 mm on each side -One bracket for a rotating beacon at the rear of the trailer -Galvanized supports under the bevel of the loading area -White reflector tape in accordance with EU regulations on the sides, on the pull-out and red at the rear -On the gooseneck and on the rear plate on the left and right, one holder each for the warning signs including socket -ALU drop sides and rear wall can be plugged onto the gooseneck approx. 2,440 x 400 mm -The rear galvanized stanchions are removable (length of the body approx. 2,560 mm) -3 pairs of WADER container pockets in the loading area for a 20ft (30ft) or a 40ft container -7 pairs of stanchion pockets for 100 x 50 mm stanchions in the outer frame of the cargo bed -Lift axle on the front axle with control by TEBS E depending on the current axle load and the current load status -Sliding suspension rails for ALU docking ramps at the rear of the vehicle -Square climbing rails 20 x 20 mm every 200 mm on the outer frame of the sloping loading area -BEKAMAX (Pico) central lubrication system with NLGI-2 standard grease and removable protection around the pump -Four warning signs approx. 423 x 423 mm, extendable by approx. 400 mm, with a position light -One bracket for rotating beacon on the warning signs Hedema Hf Rspfx Afnol -European reflector plates (red/yellow) at the rear of the trailer -Speed stickers 80 km/h at the rear and on both sides -Load manometer to determine the axle loads including load diagram -HRM metallization (High Resistance Metallization) of the outer frame -Complete steel construction shot-blasted, then the defined visible surfaces hot-finished in metallization with ZINACOR 850 (zinc 85% - aluminium 15%)

Condition: new, empty load weight: 13,500 kg, maximum load weight: 51,500 kg, overall weight: 69,500 kg, axle configuration: > 3 axles, loading space length: 8,800 mm, loading space width: 2,540 mm, loading space height: 860 mm, suspension: air, tire size: 235/75 r17.5, color: grey, Equipment: ABS, Gooseneck: Gooseneck in SNT design to optimize the loading area length, length approx. 3,700 mm Rear gooseneck with bevel approx. 1,000 mm x 10° Cargo bed: Telescopic cargo bed, length approx. 8,800 mm, with rear chamfer approx. 500 mm x 10° Recess in the chamfer and protruding into the loading area to accommodate the excavator dipper arm Pneumatic locking with conical pin and reinforced locking positions The supply lines are protected in the extendable carrier and adapt to the respective loading area length Ramps: 1 pair of two-part steel ramps, approx. 4,350 mm x 900 mm Hydraulically folding ramp tips Ramps can be moved individually hydraulically outwards by approx. 235 mm and inwards by approx. 215 mm Axles and suspension: BPW axles and suspension, two axles rigid, two axles self-steering Electromagnetic reverse lock via reverse gear and can be activated manually Air suspension with lifting and lowering valve Axle tool Hedpok Ahugefx Afnjl Tires: 235/75 R17.5 3PMSF dual tires Load index: 143/141J (144/144F) Brake system: WABCO brake system, EBS-E in accordance with EU regulations Lighting system: 24-volt lighting system in "ASPÖCK-NORDIK full LED" Metallization: Standard HRM metallization of the outer frame Complete steel construction shot-peened, then the defined visible surfaces hot-finished with ZINACOR 850 (zinc 85% - aluminum 15%) metallization Steel construction: Steel grades: S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa) Welder DIN-EN 287-1 tested MAG welding process according to EN ISO 4063 Shielding gas M21 according to EN ISO 14175 Accessories included: Steel front wall, pluggable, height approx. 400 mm ASPÖCK-UNIBOX on the front connection strip with 24N, 24S & 15-pin sockets 24N connection in accordance with ISO-118524S connection in accordance with ISO-373115-pin connection in accordance with ISO-12098 Round NATO socket on the front connection strip Cable to supply the electro-hydraulic unit and/or the electric cable winch (35 mm2, 3.5 m long) between trailer and SZM with plug (NATO-NATO) 3 kW electro-hydraulic unit for controlling the hydraulic processes, with the exception of hydraulic cable winches 1 spare wheel with mounting adapter Outer support of the gooseneck with fastening holes for screw-in lashing ringsThe first hole approx. 200 mm from the front, then approx. every 400 mm 2 pairs of screw-in lashing rings included One fastening hole in the rear upper area of the outer beams of the gooseneck for a screw-in lashing ring 1 pair of screw-in lashing rings Approx. 40 mm thick hardwood covering above the gooseneck On the gooseneck 1 pair of plug-in aluminium drop sides on the side, approx. 400 mm high, anodized One plug-in aluminium rear panel on the gooseneck, approx. 400 mm high, anodized 2" kingpin Guide plate from the gooseneck for the saddle plate, approx. 500 mm wide 4 wheel chocks with holder Holder for ALU docking lights Mech. Saddle supports with 2-speed gearbox and crank Continuous hardwood covering on the cargo bed, interrupted between the axles, approx. 50 mm thick Locking of the cargo bed with conically welded locking profiles every 250 mm incl. pretensioning plate Slotted holes for attachable and movable bridging elements on the front of the cargo bed 1 intermediate table with stepped loading surface, approx. 300 mm wide for the pull-out tube with large cross-section with sheet metal covering Front and rear with Langl

Condition: new, empty load weight: 10,350 kg, maximum load weight: 39,150 kg, overall weight: 49,500 kg, axle configuration: 3 axles, loading space length: 9,300 mm, loading space width: 2,540 mm, loading space height: 860 mm, suspension: air, tire size: 235/75 R 17,5, color: grey, Equipment: ABS, Gooseneck: -Gooseneck with rear bevel of approx. 750 mm x 10° -3 pairs of lashing rings (LC 5,000 daN) -Hardwood decking 30 mm thick Loading area: -telescopic loading area with rear slope approx. 1,000 mm x 8° -1 pair of fixed wheel recesses in front of the axles approx. 2,850 x 970 x 400 mm -Wheel recesses with square climbing strips 15 x 15 mm and widenings in the lower area -A pair of fixed wheel recesses between the 1st and 2nd axles, approx. 1,610 x 970 x 400 mm -3-piece removable galvanized covers over the wheel recesses (W 670 mm) - max. point load 5 to / pc. -Recess in the chamfer and protruding into the loading area to accommodate the excavator dipper stick approx. 2,900 x 750 x 210/290 mm -1 pair of lashing rings lying in the front of the loading area (LC 10,000 daN) -5 pairs of lashing rings foldable outwards (LC 5,000 daN) -2 pairs of lashing rings can be folded outwards (LC 10,000 daN) -2 pairs of lashing rings in the excavator trough (LC 5,000 daN) Cut-outs in the outer frame of the cargo bed for attaching lashing straps (LC 2,000 daN) One-piece ALU ramps: -One pair of one-piece ALU ramps approx. 2,500 x 600 mm -Ramp with spring lifting mechanism and manually adjustable -Maximum load per pair: 24,000 kg Axles and tires: -BPW axles and suspension, 2 axles rigid, 1 axle self-steering -Technical axle load: 12,000 kg -Electromagnetic reverse lock via reverse gear and can be activated manually Hodpfjiu Er Aox Afnel -Air suspension with lifting and lowering valve -axle tool -235/75 R 17.5 tires -TPMS tire pressure monitoring system in accordance with ECE R 141 Accessories included: -One spare wheel with holder in front of the bulkhead -2" kingpin -One galvanized steel bulkhead approx. 400 mm high -Yellow-red air couplings on the galvanized connection strip at the front -4 wheel chocks with holder on the bulkhead -Mounting in the rear area of the gooseneck for ALU docking lights -Galvanized extensions, extendable by approx. 230 mm per side -Galvanized folding supports under the bevel of the cargo bed -One bracket for a rotating beacon at the rear of the trailer -White reflector tape in accordance with EU regulations on the sides, on the pull-out and red at the rear -One bracket for the warning signs including socket on the left and right of the gooseneck and on the rear panel -ALU drop sides and rear wall can be plugged onto the gooseneck approx. 2,440 x 400 mm -The rear galvanized stanchions are removable (length of the body approx. 2,560 mm) -2 pairs of WADER container pockets in the loading area for a 20ft or 30ft container -3 pairs of stanchion pockets for 100 x 50 mm stanchions in the outer frame of the cargo bed -One removable galvanized intermediate table with 1 pair of WADER container pockets -Square climbing rails 20 x 20 mm every 200 mm on the outer frame of the loading area slope -a layer of sand painted onto the chequer plates on the gooseneck and on the loading area to prevent slipping -Four warning signs approx. 423 x 423 mm, extendable by approx. 400 mm, with a position light -A bracket for a rotating beacon on the warning signs -Speed sticker 80 km/h at the rear and on both sides -Load manometer for determining the axle loads including load diagram -HRM metallization (High Resistance Metallization) of the outer frame -Complete steel construction shot-blasted, then the defined visible surfaces hot-finished in metallization with ZINACOR 850 (zinc 85% - aluminium 15%)

Condition: new, empty load weight: 13,250 kg, maximum load weight: 47,550 kg, overall weight: 60,800 kg, axle configuration: > 3 axles, suspension: air, tire size: 245/70 r17.5, color: grey, Equipment: ABS, Gooseneck: Gooseneck with rear bevel of approx. 750 mm x 10°. 3 pairs of lashing rings Hardwood decking 30 mm thick Loading platform in extendable version: Loading area in extendable version with rear bevel of approx. 1,000 mm x 8° 5 pairs of lashing rings can be folded outwards 3 pairs of lashing rings can be folded outwards 1 pair of lashing rings lying in the front of the cargo bed Cut-outs in the outer frame of the cargo bed for attaching lashing straps Hardwood flooring approx. 48 mm thick, checker plate flooring over the axles Two-part steel ramps: A pair of galvanized two-part steel ramps approx. 2,750 + 1,400 x 800 mm with approx. 48 mm thick hardwood decking. Ramp with hydraulically folding and unfolding ramp sections, hydraulic lifting gear and hydraulically movable. Maximum load per pair: 40,000 kg Seat posts: JOST fifth wheels (mechanical) with 2-speed gearbox for 24t lifting load (50t test load) Axles and tires: BPW axles and suspension, 1st axle rigid, all other axles hydro-mechanically forced steered Technical axle load: 12,000 kg Air suspension with lifting and lowering valve Axle tool Tires 245/70 R 17.5 Brake system: Brake system in accordance with EU regulations with EBS-E (4S3M) without connecting lines to the tractor unit Steel construction: Steel construction made of high-strength fine-grained steels Steel grades: S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa) Coating: First-class and durable corrosion protection of the standard shot-peened welded frame guaranteed by a 2-component (2K) zinc dust primer A high-quality 2-component (2K) top coat in a single color in nova grey Rear section metallized and painted in RAL 9010 (pure white) No metallic paint finish possible Electrical system: Electrical system in accordance with EU regulations, 24 volt lighting ASPÖCK-NORDIK (ASS3) ASPÖCK-UNIBOX on the front connection strip with 24N, 24S & 15-pin sockets Connection according to ISO 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Accessories included: 2" kingpin One galvanized steel end wall approx. 400 mm high Yellow-red air couplings on the galvanized connection strip at the front 4 restraining shoes with holder on the bulkhead One spare wheel with holder in front of the bulkhead Electro-hydraulic unit Re-steering from the front and rear by means of cable remote control operated via pushbuttons with tracking control of the axles Mounting in the rear area of the gooseneck for ALU docking lights European reflector plates (red/yellow) at the rear of the trailer Hodjl Uxdkopfx Afnsl White reflective tape in accordance with EU regulations on the side, on the extension and at the rear Red On the gooseneck and on the ramps on the left and right, a holder for the warning signs including a socket A bracket for a rotating beacon at the rear of the trailer Galvanized folding supports under the sloping loading area Operating valves for the ramps fitted on the right-hand side of the trailer Cover plates to bridge the gap between the ramps and the cargo bed A mud flap at the rear of the trailer Manual and description on USB stick BEKAMAX (Pico) central lubrication system with NLGI-2 standard grease and removable protection around the pump ALU drop sides and rear wall can be plugged onto the gooseneck approx. 2,440 x 400 mm The rear galvanized stanchions are removable Length of the body approx. 2,560 mm One tool box INOX 1,350 x 400 x 400 on the gooseneck Box covered oil filler plug 4 pairs of WADER container pockets in t

Condition: new, empty load weight: 12,900 kg, maximum load weight: 34,100 kg, overall weight: 47,000 kg, axle configuration: 2 axles, loading space length: 6,850 mm, loading space width: 2,540 mm, loading space height: 350 mm, suspension: other, tire size: 245/70 R 17,5, color: grey, operation weight: 12,900 kg, Equipment: ABS, Gooseneck: -Gooseneck in SNT design to optimize the loading area length, length approx. 3,750 mm -Gooseneck can be raised/lowered hydraulically and removed -Technical fifth wheel load: 23,000 kg -For tractor units: 4 x 2, 6 x 2 and 6 x 4 Loading area: -Low bed with external supports in extendable "SUPER LOW" design, length approx. 6,850 mm -Low bed with solid hardwood floor approx. 40 mm thick and mechanical locking Rear chassis: -Rear chassis with closed external frame, checker plate covering and continuous prism excavator trough approx. 1,250/700 x 505 mm, open at the rear -2 pairs of lashing rings that can be folded outwards -1 pair of lashing rings lying in the trough -2 pairs of stake pockets for plug-in stakes 100 x 50 mm in the outer frame Pendulum axle and tires: -"PENDEL-AXLE", all axles hydromechanically forced steered Hjdpfshlz R Ssx Afnel -Hose rupture valve on the axle compensation cylinder with automatic RESET function -Hydraulic cylinder with shut-off valves and pins for securing in raised position -Final painting of axles with 2 layers of 2-component paint, painted in a single color in "FAY-Gray-34-0260" -Technical axle load: 12,000 kg -Hydraulic axle compensation -Tires 245/70 R 17.5 -TPMS tire pressure monitoring system in accordance with ECE R 141 Accessories: -Preparation for screw-on container positioning for 1x 20ft or 1x40ft container on the outer supports -2" kingpins -A galvanized steel front wall approx. 400 mm high -One spare wheel -Yellow-red air couplings on the galvanized connection strip at the front -4 wheel chocks -Steering from the front and rear can be operated using a cable remote control via push buttons, with alignment control of the axles -Hydraulic connections from the gooseneck to the low bed with multi-coupling instead of screw couplings -Electro-hydraulic unit -White reflector tape in accordance with EU regulations on the side, on the extension and at the rear -European reflector signs (red-yellow) on the rear of the trailer -One holder for the warning signs including a socket on the gooseneck and on the rear panel on the left and right -6 pairs of threaded blocks between the lashing rings under the top strap on the outer support for mounting screwable RUD rings VLBG-4 -ALU side walls and rear wall can be plugged into the gooseneck approx. 2,440 x 400 mm -The rear galvanized plug-in stanchions are removable (Length of the body approx. 2,560 mm) -Gooseneck in the rear upper area closed with a removable cover -5 pairs of stake pockets for 100 x 50 mm stakes in the outer frame of the loading area -Foldable extensions, approx. 230 mm per side -2 pairs of screwable RUD rings VLBG-4 M24 (LC 8,000 daN) -1 pair of steel ramps to bridge the hooks of the low bed -A painted layer of sand on the loading area as anti-slip protection -Speed sticker 80 km/h at the rear and on both sides -Dipper handle recess of the rear chassis closed at the rear with a plug-in plate -Four warning signs extendable by approx. 400 mm, approx. 423 x 423 mm -Radio remote control for the steering in addition to the cable remote control, with indicator lights on the receiver as Alignment control -Central lubrication system with 2 BEKAMAX (Pico) pumps with NLGI-2 normal grease -Load pressure gauge for determining axle loads -HRM metallization (High Resistance Metallization) of the outer frame -Complete steel construction shot blasted, then the defined visible surfaces are hot-finished in metallization with ZINACOR 850 (zinc 85% - aluminum 15%)

Condition: new, empty load weight: 17,250 kg, maximum load weight: 48,700 kg, overall weight: 66,000 kg, axle configuration: 3 axles, loading space length: 7,550 mm, loading space width: 2,480 mm, loading space height: 375 mm, tire size: 245/70 R 17.5, color: grey, operation weight: 17,250 kg, Equipment: ABS, Gooseneck: -Gooseneck in SNT design to optimize the loading area length, length approx. 3,750 mm -Gooseneck can be raised/lowered and removed hydraulically -For tractor units: 6 x 4 and 8 x 4 (or 6 x 4 with optional 1-axle dolly) Low bed: -Low bed with external supports, designed as a telescopic tank bridge in low construction with extension at the front -Length x width approx. 7,550 mm x 2,740 mm -Mechanical locking of the extension Chassis: -Chassis at the rear with closed outer frame -Checker plate covering and continuous prism excavator trough approx. 1,450/900 x 505 mm, open at the rear Axles, suspension and tires: -"PENDEL-AXLE", all axles hydromechanically forced steering -Hose rupture valve on the axle compensation cylinder with automatic RESET function -Hydraulic cylinder with shut-off valves and pins for securing in raised position -Final painting of axles with 2 layers of 2-component paint in a single color in "FAY-Gray-34-0260" -Technical axle load 12,000 kg Hjdpfx Ash Hm Tzefnol -Hydraulic axle compensation -245/70 R 17.5 Accessories: -Steel bulkhead, plug-in, approx. 400 mm high -4 wheel chocks -Gooseneck in the rear upper area closed with a removable cover -1 pair of steel ramps with climbing strips and fastening bolts to bridge the hooks of the low bed -The ramps can be placed over or between the hooks -Fastening options for the steel ramps at the rear between the outer supports of the gooseneck -One Locking point approximately every 1,000 mm on the extension -1 lashing ring on the left and right on the front cross member -Connection strip for supply lines to the tractor unit, attached at the height of the outer frame profile -6 pairs of threaded blocks on the outside of the inner supports of the loading area for mounting screwable rings M24 -6 pairs of countersunk lashing rings on the outside of the outer supports of the loading area, foldable inwards and outwards -1 pair of threaded blocks at the front and rear of the outer supports of the loading area for mounting screwable rings M24 -Hanging strip for loose aluminum loading ramps on the vehicle's end cross member -Central lubrication system with 2 pumps, BEKAMAX brand -Steering from the front and rear, operated by cable remote control, with alignment control of the axles -3 kW electro-hydraulic unit for controlling the hydraulic processes, with the exception of hydraulic cable winches -Removable loading floor (galvanized) in 3 elements can be inserted between the outer supports with hardwood flooring -Foldable extensions, by approx. 230 mm per side -Extension planks, loose, framed in steel -4 warning signs approx. 423 x 423 mm -Radio remote control for operating the steering -3.5" king pin -Anti-slip sticker on the left bevel of the gooseneck -Hydraulic connections from the gooseneck to the low bed with multi-coupling instead of screw couplings -Guide plate from the gooseneck for the fifth wheel plate, approx. 800 mm wide -1 spare wheel with mounting adapter -Parking position on the gooseneck for the warning signs when not in use -2 pairs of stake pockets embedded in the outer frame of the chassis, for plug-in stakes approx. 100 x 50 mm -Dipper handle recess of the rear chassis closed at the back with a plug-in plate -Color of the trailer MB 7350 Novagrau

Condition: new, maximum load weight: 49,000 kg, overall weight: 60,800 kg, axle configuration: > 3 axles, loading space length: 9,300 mm, loading space width: 2,540 mm, loading space height: 860 mm, suspension: air, tire size: 235/75 r 17.5, color: grey, Equipment: ABS, Gooseneck: -Gooseneck with beveled corners at the front 45° and with rear bevel of approx. 750 mm x 10° -3 pairs of lashing rings (LC 5,000 daN) -Hardwood decking 30 mm thick Loading area in extendable version: -Loading surface in extendable version with rear bevel of approx. 1,000 mm x 8° -5 pairs of lashing rings can be folded outwards (LC 5,000 daN) -3 pairs of lashing rings can be folded outwards (LC 10,000 daN) -1 pair of lashing rings lying in the front of the cargo bed (LC 10,000 daN) Cut-outs in the outer frame of the cargo bed for attaching lashing straps. (LC 2,000 daN) -Hardwood flooring approx. 48 mm thick, checker plate flooring over the axles Removable two-part ramps: -A pair of galvanized two-part steel ramps approx. 2,750 + 1,400 x 800 mm with approx. 48 mm thick hardwood decking -Ramp with hydraulically folding and unfolding ramp sections, hydraulic lifting gear and hydraulically movable -Maximum load per pair: 40,000 kg Seat posts: -JOST fifth wheels (mechanical) with 2-speed gearbox for 24 t lifting load (50 t test load) Axles and tires: -BPW axles, two axles rigid two axles self-steering, air-suspended, with drum brake, with lifting/lowering function The self-steering axles with electro-magnetic reverse lock can be activated via reverse gear or manually -axle tool -235/75 R 17.5 tires Brake system: -brake system in accordance with EU regulations with EBS-E (4S3M) Steel construction: -steel construction made of high-strength fine-grained steels -Steel grades: -S355J2+N/S355MC (yield strength 355MPa) -S690QL/S700MC (yield strength 690MPa) Coating: -First-class and durable corrosion protection of the standard shot-peened welded frame guaranteed by a 2-component (2K) zinc dust primer A high-quality 2-component (2K) top coat in a single color in nova grey Electrical system: -Electrical system in accordance with EU regulations, 24 volt ASPÖCK-NORDIK lighting (ASS3) ASPÖCK-UNIBOX on the front connection strip with 24N, 24S & 15-pin sockets Accessories included: -2" kingpin -One galvanized steel bulkhead approx. 400 mm high -One spare wheel with holder in front of the bulkhead -Yellow-red air couplings on the galvanized connection strip at the front -4 wheel chocks with holder on the bulkhead -Mounting in the rear area of the gooseneck for ALU docking ramps -Galvanized folding supports under the bevel of the cargo bed -One bracket for a rotating beacon -Cover plates to bridge the gap between ramps and cargo bed -White reflector tape in accordance with EU regulations on the sides, on the extension and red at the rear Hjdpfx Aoh Etf Rofnol -Electric hydraulic unit -On the gooseneck and on the ramps on the left and right a holder for the warning signs including socket -Control valves for the ramps mounted on the right-hand side of the trailer -One mud flap at the rear of the trailer -Manual and description on USB stick -ALU drop sides and rear wall can be plugged onto the gooseneck approx. 2,440 x 400 mm -The rear galvanized stanchions are removable (length of the body approx. 2,560 mm) -4 pairs of WADER container pockets in the loading area for one 20ft, 2x 20ft or one 40ft container -7 pairs of stanchion pockets for 100 x 50 mm stanchions in the outer frame of the cargo bed -Galvanized extensions, extendable by approx. 230 mm per side -Lift axle on the front axle with controls -Square climbing rails 20 x 20 mm -BEKAMAX central lubrication system -Four warning signs extendable by approx. 400 mm approx. 423 x 423 mm

Condition: new, empty load weight: 17,500 kg, maximum load weight: 43,500 kg, overall weight: 61,000 kg, axle configuration: 3 axles, loading space length: 7,550 mm, loading space width: 2,750 mm, loading space height: 400 mm, tire size: 245/70 R 17.5, color: grey, Equipment: ABS, Gooseneck: -Gooseneck in SNT design to optimize the loading area length, length approx. 3,750 mm -Gooseneck can be raised/lowered and lowered hydraulically -For tractor units: 6x4 or 8x4 Drop deck: Hedpfx Afeh Hm Thjnol -Low bed with external beams in extendable design, "SUPER LOW" design, length approx. 7,550 mm -Low bed with solid hardwood floor approx. 40 mm thick and mechanical locking mechanism The supply lines are protected in the pull-out supports and automatically adjust to the respective drop-down bed length Rear chassis: -Rear chassis with closed outer frame, checker plate covering and continuous Prisma excavator trough approx. 1,450/900 x 505 mm, open at the rear -2 pairs of stanchion pockets for 100 x 50 mm stanchions in the outer frame Axles and tires: -"PENDEL-AXLE", all axles with hydromechanical forced steering -Hose rupture valve on the axle compensation cylinder with automatic RESET function -Hydraulic cylinder with stopcocks and locking pin for securing in raised position -Technical axle load: 12,000 kg -Hydraulic axle compensation -245/70 R 17.5 / 3PMSF tires Accessories included: -Preparation for mounting bolt-on container positioners for 1x 20ft or 1x 40ft container on the outer beams -2" kingpin -One galvanized steel end wall approx. 400 mm high -One spare wheel with holder -Yellow-red air couplings on the galvanized connection strip at the front -4 wheel chocks -Steering can be operated from the front and rear by remote control cable via pushbuttons, with axle tracking control -Hydraulic connections from the gooseneck to the low bed with multi-coupling instead of screw coupling -Electric hydraulic unit -White reflector tape in accordance with EU regulations on the side, on the extension and red at the rear -2 wooden blocks 500x250x200 mm -European reflector plates (red/yellow) at the rear of the trailer -On the gooseneck and on the rear plate on the left and right, one holder each for the warning signs including socket -Central lubrication system with 2 BEKAMAX (Pico) pumps with NLGI-2 standard grease -Load manometer for determining the axle loads including load diagram -ALU drop sides and rear wall can be plugged onto the gooseneck approx. 2,000 x 400 mm -The rear galvanized stanchions are removable (length of the body approx. 2,120 mm) -Separate air connection with air gun on the gooseneck -Duomatic air coupling from gooseneck to low bed -Gooseneck closed in the rear upper area with a removable cover -1 pair of steel ramps for bridging the mounting hooks of the low bed -Four warning panels approx. 423 x 423 mm, extendable by approx. 400 mm -Radio remote control for steering in addition to the cable remote control, with indicator lights on the receiver for tracking control 6 pairs of threaded blocks between the lashing rings under the top chord on the outer beam for mounting screw-on RUD rings VLBG-4 -7 pairs of stanchion pockets for 100 x 50 mm stanchions in the outer frame of the cargo bed -folding extensions, approx. 230 mm on each side -A layer of sand painted onto the loading surface to prevent slipping Dipper arm recess of the rear chassis closed at the front and rear with a plug-in plate -HRM metallization (High Resistance Metallization) of the outer frame -Complete steel construction shot-blasted, then the defined visible surfaces hot-finished with ZINACOR 850 metallization (zinc 85% - aluminium 15%)

Condition: new, empty load weight: 15,420 kg, maximum load weight: 61,080 kg, overall weight: 76,500 kg, axle configuration: > 3 axles, loading space length: 8,600 mm, loading space width: 2,540 mm, loading space height: 900 mm, tire size: 235/75/r17,5, color: grey, Equipment: ABS, Gooseneck: Gooseneck with rear bevel of approx. 750 mm x 10° 3 pairs of lashing rings Hardwood decking 30 mm thick Loading platform: Loading area in extendable design with rear bevel of approx. 500 mm x 8° 8 pairs of lashing rings can be folded outwards 1 pair of lashing rings lying in the front of the cargo bed Cut-outs in the outer frame of the cargo bed for attaching lashing straps Hardwood flooring approx. 48 mm thick, checker plate flooring over the axles Two-part steel ramps: A pair of galvanized two-part steel ramps approx. 2,750 + 1,400 x 800 mm with approx. 48 mm thick hardwood decking. Ramp with hydraulically folding and unfolding ramp sections, hydraulic lifting gear and hydraulically movable. Maximum load per pair: 50,000 kg. Seat posts: - JOST fifth wheels (mechanical) with 2-speed gearbox for 24t lifting load (50t test load). Axles and tires: BPW axles and suspension, 4th + 5th axle self-steering Technical axle load: 12,000 kg 4th and 5th axles with electro-magnetic reverse lock via reverse gear and manual activation Tires 235/75 R 17.5 3PMSF Brake system: Brake system in accordance with EU regulations with EBS-E (4S3M) Sockets and lighting: Electrical system in accordance with EU regulations, 24 volt lighting ASPÖCK-NORDIK (ASS3) ASPÖCK-UNIBOX on the front connection strip with 24N, 24S & 15-pin sockets Connection according to ISO 24N ISO-1185 24S ISO-3731 15 pole ISO-12098 Paint finish: First-class and durable corrosion protection of the standard shot-peened welded frame guaranteed by a 2-component (2K) zinc dust primer A high-quality 2-component (2K) top coat in a single color in MB 7350 nova grey Rear section metallized and painted in RAL 9010 (pure white) No metallic paint finish possible Hedpfol Sl Izsx Afnel Steel construction: Steel construction made from high-strength fine-grained steels Steel grades: S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa) Accessories: One spare wheel with holder in front of the bulkhead 2" kingpin One galvanized steel bulkhead approx. 400 mm high Yellow-red air couplings on the galvanized connection strip at the front 2 restraining shoes with holder on the bulkhead Mounting in the rear area of the gooseneck for ALU docking lights A bracket for a rotating beacon at the rear of the trailer Galvanized supports under the bevel of the loading area White reflective tape in accordance with EU regulations on the sides, on the extension and red at the rear Electro-hydraulic unit at the rear under the cargo bed A holder for the warning signs, including a socket, on the gooseneck and on the rear panel on the left and right respectively Control valves for the ramps mounted on the right-hand side of the trailer A mud flap at the rear of the trailer Manual and description on USB stick 3.5" kingpin supplied loose ALU drop sides and rear wall can be plugged onto the gooseneck approx. 2,440 x 400 mm (LxH) The rear galvanized stanchions are removable (length of the body approx. 2,560 mm) 3 pairs of WADER container pockets in the loading area for a 20' (30') or a 40' container 6 pairs of stanchion pockets for 100 x 50 mm stanchions in the outer frame of the cargo bed Galvanized extensions, extendable by approx. 230 mm per side Lift axle on the front axle with control by TEBS E depending on the current axle load and the current load status Square climbing rails 20 x 20 mm every 200 mm on the outer frame of the loading area slope On the chequer plates, above the kingpin and the load floor

Condition: new, maximum load weight: 37,390 kg, overall weight: 48,000 kg, axle configuration: 3 axles, Year of construction: 2026, * TS 3 RM ML 30.0: ----Brakes: * Wabco EBS-E (electronic braking system) * Emergency release device for spring brake cylinders * Drum brakes ----Axles: * 3 x 11 t BPW axles * Start-up aid for shunting purposes on the first axle, activated via EBS (no truck-side installation required) * Rear axle as trailing steering axle with electro-pneumatic steering lock * Locking of the trailing axle from the cab for shunting purposes, activated via EBS (no truck-side installation required) ----Suspension: * Air suspension with lifting and lowering system as well as RtR valve ----Electrics / Lighting: * Smart-Board mounted on the trailer as an infotool, with pressure sensors for total axle load display * 15-pin power connector * LED lighting 12 / 24 V * Removable LED beacon at the rear * 2 additional LED reversing lights * 7-pin socket at the rear for oversize lighting * Side marker lights with indicator function * Tire pressure monitoring system with display option in the truck via EBS signal (no truck-side installation required) ----General attachments: * Side underrun protection * Landing legs at the front and swing-down supports at the rear of the chassis * Straight steel sheet fenders * Spare wheel holder in front of the front wall cross member (spare wheel not included) * Mechanically adjustable warning sign packages front and rear * Pivoting arm as a carrier for connection lines from the truck to the semi-trailer ----Low loader deck: * 2nd king pin position * Fifth wheel platform with front corners beveled at 45°, front toolbox of galvanized, powder-coated steel sheet (W = 2,480 x H = 500 x L = 665 mm) with folding lid * 400 mm aluminum drop sides (in RAL color of your choice), foldable and removable, on the sides of the fifth wheel platform * Rear board -150 mm- plugged in high * Rear beveled section at the fifth wheel platform leading to the low bed, approx. 700 mm long with checker plate cover; at the end, a perforated strip for hanging aluminum drive-on ramps * Fifth wheel platform with 50 mm clamped wooden planks, low bed platform with 60 mm clamped wooden planks * Tread plate over the axles * 9x mechanical folding extensions to 3 m overall width, except in the rear bevel (extension planks available with closed storage compartment running transverse to the driving direction under the loading area) * 3 recesses under the fifth wheel platform for storing optional aluminum drive-on ramps or wooden planks for wheel recess covers ----Load securing (LaSi package): Fifth wheel platform: * Perforated outer frame with 45° edges, hole pattern for lashing equipment (2 t lashing force per lashing point at minimum spacing of 480 mm) Hodpfx Afjtpta Djnsl * 3x 13.4 t lashing rings recessed in the floor on each side (1x on the fifth wheel platform, 1x on the side members after the step, 1x above the middle axle next to the side member) Low loader platform: * 3x 13.4 t lashing rings on the outer frame on each side (1x at start of step on the fifth wheel platform, 1x at start of the ramp, 1x at end of the ramp) * 2x 10 t lashing rings on each side (1x between front wheel well and 1st axle, 1x between 2nd and 3rd axle) * 3x 5 t lashing rings on each side, bolted to the external frames of the wheel wells (2 at the front, 1 at the rear wheel well) ----Excavator arm trough: * Extended excavator arm trough from the end of the last rigid axle over the steering axle to the rear cross member, continuous, with internal reinforcement profile approx. W = 770 mm x dept

Condition: new, maximum load weight: 29,850 kg, overall weight: 38,000 kg, axle configuration: 2 axles, loading space length: 8,000 mm, loading space width: 2,520 mm, Year of construction: 2026, TS 2 ML ----Brakes: * EBS-E (electronic braking system) * Emergency release device for spring brake cylinders * Drum brakes ----Axles: * 2 x 10 t axles * Rear axle as a trailing steering axle with electro-pneumatic steering lock activated by PIN when reverse gear is selected * Additional lock for the trailing axle, operated from the driver's cab for maneuvering purposes – no truck-side installation required – assigned to PIN 10. The lock must be deactivated before driving on public roads ----Suspension: * Air suspension with lifting and lowering function as well as RtR (Ride to Recover) function ----Electrics / Lighting: * Tire pressure monitoring system with display option in the truck dashboard via EBS signal – no truck-side installation required * LED tail lights 12 / 24 V * Flashing side marker lights * LED reversing lights switched via reverse gear * SmartBoard installed as info tool with pressure sensors exclusively for total axle load display * 7-pin socket at the rear for overlength lighting * Removable LED rotating beacon at the rear ----General attachments: * Aluminum air tanks * Mechanical crank landing legs * Galvanized steel mudguards * Swivel arm as a carrier for connection lines mounted in front of the front panel ----Warning package: * Mechanically adjustable warning sign package ----Low-bed platform: * 50 mm flooring made of larch / Douglas fir instead of spruce / fir * Rear slope – 700 mm long – on the gooseneck deck to the low-bed with checker plate covering, and perforated strip at the end for attaching aluminum approach ramps * Tread plate cover over wheels * SP-Combo package: toolbox with 45° corners, made of galvanized sheet steel, additionally powder-coated in RAL 9006 white aluminum, mounted on the platform approx. 2,480 x 500 mm * Flip-top lid as well as side doors in the slanted corners * Folding aluminum side walls 500 mm high on the platform, incl. folding and removable rear stanchions * Plug-in aluminum rear wall 150 mm high * Second kingpin position * Preparation for container lock * Preparation for 3 insert pockets in the inclined ramp from low-bed to gooseneck * Preparation for retrofitting folding outriggers for 3 m widening by welding the mounting brackets into the outer frame ----Load securing: Fifth wheel platform: * In the front corners and at the front, 50 mm holes for 1.2 t lashing force per hole * 2 x 16.5 t lashing rings recessed in the floor on the side at the approach slope * Perforated and bent 45° outer frame with hole pattern for lashing equipment (2 t lashing points every 480 mm) * On each side: 2 x 6.3 t retractable lashing rings recessed into the outer frame Low-bed platform: * 2 x 16.5 t lashing rings recessed centrally directly in front of the approach slope to the gooseneck * On each side: 3 pairs of 13.5 t and 5 pairs of 10 t retractable lashing rings recessed into the outer frame * On each side: 4 stanchion pockets recessed into the outer frame * Profifix lashing rail centered in the longitudinal axis (lashing point 3 t per securing circle) ----Excavator arm trough: * From the end of the last rigid axle to the end cross member B = 770 mm, D = 270 mm (on each side 2 x 6.4 t lashing rings for the excavator arm trough, permanently welded) Hedpfx Afjykx I Tonol ----Ramp: * Hydraulic one-piece "ALLTEC" aluminum approach ramps approx. 3,200 x 750 mm * Load capacity 13 t per ramp (26 t per pair) * Hydraulic ramp shifting on sliding pipe of the ramp shaft ----Hydraulics: * Hydraulic flow

Condition: used, empty load weight: 16,200 kg, maximum load weight: 48,050 kg, overall weight: 64,250 kg, axle configuration: > 3 axles, first registration: 08/1976, loading space length: 7,800 mm, loading space width: 3,150 mm, loading space height: 1,380 mm, total height: 131,000 mm, suspension: steel, tire size: 445/65R22.5, color: green, mileage: 1,001 km, gearing type: other, driver cabin: other, Vehicle location: Bovenden, 4 axles, Kässbohrer axles, leaf suspension, forced steering, lashing rings, 2-piece loading ramps, front support. Bodywork: 750 mm ramp width, fifth wheel height 1550 mm, king pin 3 ½", 4 x 13t axles, 4 axles with hydraulic forced steering, overall length 13,100 mm. Hedpfxjxyzyis Afnol ACCESSORY DETAILS WITHOUT WARRANTY, subject to modifications, intermediate sale and errors excepted!

Condition: new, maximum load weight: 38,290 kg, overall weight: 48,000 kg, axle configuration: 3 axles, loading space length: 8,500 mm, loading space width: 2,520 mm, Year of construction: 2026, * TS 3 Profile 30.0: ----Brakes: * Wabco EBS-E (electronic braking system) * Emergency release device for spring-loaded cylinders * Drum brakes ----Axles: * 3 x 11 t BPW Eco Plus axles * Last axle is self-steering with electro-pneumatic steering lock ----Suspension: * Air suspension with lifting and lowering system as well as RtR (Raise-the-Roof) valve ----Electrics / Lighting: * TPMS (Tire Pressure Monitoring System) * Smartboard control box mounted on the trailer as an info tool, with pressure sensors for total axle load display * 15-pin power plug * LED lighting system 12 / 24V * Removable LED beacon at the rear left ----General Fittings: * Side underrun protection * Support winches at the front and mechanical swing-down supports at the rear of the chassis * Straight steel mudguards * Spare wheel holder under the chassis on the right side ----Lowbed Area: * Saddle platform with 45° chamfered front corners and front toolbox made from galvanized sheet steel, W = 2,480 x H = 500 x L = 665 mm, with hinged lid * 400 mm aluminium drop sides (RAL 9010 pure white) on the sides of the saddle platform, foldable and removable * Rear wall inserted, 150 mm high * Rear incline on the saddle platform to the lowbed, approx. 700 mm long * Saddle platform with 50 mm timber planks and lowbed platform with 60 mm timber planks * Tread plate above the axles ----Extensions: * 8 x mechanical fold-out extensions up to a total width of 3 m, not on the rear incline (extension planks available and stored on the saddle platform) * Mechanically adjustable warning sign packages front and rear ----Load Securing (Lashing Package): * On the saddle platform: 2 x 6.3 t lashing rings each, as well as 3 x 5 t lashing rods on each side of the external frame * On the lowbed platform: 2 x 13.4 t lashing rings on each side, as well as 4 x 10 t lashing rings, swingable and lowerable, embedded in the external frame * On each side: 2 x 6.4 t lashing eyes, and 1 lashing ring at the excavator stick recess at the rear * 2 x container locks directly after the step in the lowbed platform ----Excavator Stick Recess: * Excavator stick recess from the end of the last fixed axle, over the steering axle, up to the rear cross member, continuous with internal reinforcement profile, approx. L = 2,450 x W = 770 mm x D = 270 mm ----Access Ramps: * Mechanical one-piece, hot-dip galvanized hydraulic access ramps approx. 3,000 x 720 mm (mechanically adjustable sideways) * 4-way control block for future customer installation of hydraulic ramp shifting * The outer board of the ramp consists of 50 mm hardwood * Climbing strips on the outer frame of the ramp and on the approach incline ----Hydraulics: * Hydraulic flow divider in the trailer (for truck hydraulic pump capacity from over 40 l/min up to 120 l/min) ----Load Dimensions: * Loading surface of the saddle platform: approx. 3,935 x 2,480 mm * Lowbed loading area: approx. 8,500 x 2,520 mm * Loading height unladen approx. 910 mm (incl. 860 mm approach incline) ----Fifth Wheel Height: * approx. 1,220 mm (suitable for 2- and 3-axle tractors) ----Paintwork: Hjdpfx Ael Tnvgsfnjl * Chassis, ramps, rear folding supports, widening adapters hot-dip galvanized * Axles, support winches, air tanks painted black * Vehicle is hot-dip galvanized ----Information: * New vehicle with manufacturer's warranty * Errors and prior sale excepted * Sample images may show equipment not included in the offered vehicle ----Delivery Time: * Available from week

Condition: used, maximum load weight: 43,640 kg, overall weight: 65,000 kg, axle configuration: > 3 axles, first registration: 10/2013, Semi-trailer with air suspension and hydraulic dual-circuit forced steering (turntable steering) Loading platform from 15,475 mm up to 54,575 mm Loading Platform - "Flatbed" design, quadruple extendable, stepped gooseneck - Mechanical landing gear - Front corners at 90°, closed external frame - Integrated steering linkage in the front frame - Turntable-mounted fifth wheel plate with interchangeable 2" kingpin and adjustable steering wedge - Rear crossmember as sturdy underride protection Chassis - 4-axle chassis with air suspension including lifting and lowering valve Hedeyltm Hepfx Afnel - BPW axles with adjustable tapered roller bearings Braking System - Dual-line, full-air, all-wheel brake system with diaphragm brake cylinders - Automatic load-dependent brake (ALB) - Automatic slack adjusters (AGS) - Parking brake via spring-loaded cylinders - ABV (ABS) Loading Platform L x W 15,475 mm x 2,520 mm Extendable: 9,800 mm + 9,700 mm + 9,800 mm + 9,800 mm, total length up to 54,575 mm Loaded loading height: 1,305 mm At a loaded saddle height: 1,300 mm Rear steering radius: 2,350 mm Gooseneck: 25,000 kg Axle loads: 4 x 10,000 kg Steering 1st – 4th axle hydromechanically forced-steered (dual-circuit steering) (turntable steering) Electric power pack with radio remote control

Condition: used, empty load weight: 22,900 kg, maximum load weight: 41,100 kg, overall weight: 64,000 kg, axle configuration: > 3 axles, first registration: 10/2009, suspension: air, tire size: 235/75 17,5, tire condition: 70 %, color: green, Year of construction: 2009, front tire size: 235/75 17,5, rear tire size: 235/75 17,5, driver cabin: day cab, emission class: none, Equipment: ABS, truck registration, Reference number for inquiries: 40194 Goldhofer, STZ-VL4-42/80A * Year of manufacture: 2009 * ABS, Anti-lock Braking System * Air suspension * Steering axle * Air connection coupling head (red + yellow) * Spare wheel holder with spare tire * Connection plug: 2x 7-pin * Lifting and lowering device * Extendable * Telescopic – telescopic semi-trailer * Heavy-duty lashing eyes * Suspension: Air * Gross vehicle weight: 64,000 kg * Unladen weight: 22,900 kg * Payload: 41,100 kg * Permissible gross weight: 64,000 kg * Axle manufacturer: BPW * Tire condition 1st axle: 70% – 70% | Tire size: 235/75 R17.5 * Tire condition 2nd axle: 70% – 70% | Tire size: 235/75 R17.5 * Tire condition 3rd axle: 70% – 70% | Tire size: 235/75 R17.5 * Tire condition 4th axle: 70% – 70% | Tire size: 235/75 R17.5 * Tire sizes: 235/75 R17.5 * Telescopable approx. 4,000 mm * Deck height above axles: approx. 1,000 mm * Deck height above ground: approx. 360 mm * Expandable to 3,200 mm * Removable gooseneck Liability disclaimer: Subject to modifications, prior sale, and errors excepted. More photos and videos are available on our homepage. Our comprehensive range of services includes, for example: * Purchase / sale / rental of commercial vehicles * Quick and uncomplicated financing Hedpoyict Usfx Afnol * Processing of all (export) documents * Ordering export / customs license plates * Vehicle preparation: new tarpaulins, lettering, paintwork, etc. * Professional loading / load securing * TÜV inspections, registration service * Transfer of commercial vehicles Consult our trained specialist staff – we are happy to advise you.