Used working platform trailers for sale (70)

Condition: new, maximum load weight: 30,440 kg, overall weight: 40,000 kg, axle configuration: > 3 axles, Year of construction: 2026, Equipment: ABS, T 4 Profi 40.0 ----Brakes: * Wabco EBS-E (electronic braking system) * Emergency release system for spring-loaded cylinders * Drum brakes ----Axles: * 4 x 11-ton Gigant axles ----Suspension: * Air suspension with lifting and lowering system and RtR valve ----Drawbar: * Straight drawbar with 50 mm drawbar eye and stepless height adjustment ----Electrical System / Lighting: * Tire pressure monitoring system with display option in the truck display via EBS signal - without truck-side installation - * SmartBoard as an information tool with pressure sensors for axle load display per axle group * 15-pin power connector * LED rear lights * LED marker lights (removable) at the rear ----General Components: * Warning sign packages at the front & rear * 2 x toolboxes made of galvanized, powder-coated steel sheet, approx. 650 x 300 x 600 mm, on the right side * Closed plastic fender at the front * Straight steel mudguards at the rear, each with splash protection (spray mist suppression) * Lateral impact protection ----Low-bed Platform: * Extension of the turntable platform by 520 mm with 45° corners and 3 recessed storage compartments incl. lids and locking mechanism * Floor over the turntable platform made of 50 mm needlewood, and in the low-bed platform made of 60 mm needlewood * Rubber coating 20 mm instead of wooden floor in the running area with a low-bed length of 6,780 mm including the access ramp * Rubber coating on the access ramp, left and right, approx. 860 mm long * 4 lashing eye pockets on each side (however, no lashing bars included) with simultaneous 2-ton lashing capability ----Chassis: * Chassis made of high-strength fine-grain steel ----Load Securing (Lasi - Package): Turntable Platform: * 2 pairs of 13.4-ton lashing eyes in the outer frame of the turntable platform Low-bed: * 4 pairs of 10-ton lashing eyes on each side of the outer frame, retractable and loadable in all directions * 2 pairs of 13.4-ton swiveling lashing eyes on each side at the rear ----Ramps: * Rubber coating on the folding access ramps * Hydraulic folding ramps with hydraulic extendable front section, approx. 4,650 x 720 mm * Hydraulic lateral ramp adjustment & load holding valves ----Rear Support: * Hydraulic rear support ----Width Extension: Tjdpfx Aoylfvgjkcja * 8 pairs of galvanized folding outriggers for 3 m overall width (however, not in the rear slope) * Width extension boards stored in a compartment on the left side ----Excavator Arm Rest: * Excavator arm rest above the rear axle to the end of the access ramp, approx. L=2,100 mm x W=740 x D=190 mm * 2 pairs of 6.4-ton lashing eyes on the side in the excavator arm rest ----Hydraulics: * Hydraulic flow divider in the trailer (with hydraulic pump output in the truck of over 40 - max. 120 l/min.) ----Loading Dimensions: * Rear loading area: approx. 6,780 x 2,520 mm (incl. 860 mm access ramp) * Loading area above the turntable: approx. 2,990 x 2,520 mm ----Loading Height: * approx. 890 mm, +/- 20 mm ----Painting: * Reflective contour striping on the sides and at the rear * Chassis, turntable, access ramps, and folding outriggers hot-dip galvanized * Axles, drawbar, air tanks, and turntable painted in a black color ----Information: * New vehicle with manufacturer's warranty * Subject to errors and prior sale ----Delivery Time: * Immediately available from Egestorf

Condition: used, maximum load weight: 31,000 kg, overall weight: 40,000 kg, axle configuration: > 3 axles, first registration: 07/2024, loading space length: 9,290 mm, loading space width: 2,520 mm, loading space height: 950 mm, * PT 40.0 Profi ----Brakes: * Wabco EBS-E (electronic braking system) * Emergency release system for spring brake cylinders * Drum brakes ----Axles: * 4 x 11-ton Gigant axles ----Suspension: * Air suspension with lifting and lowering system and rapid drop valve ----Drawbar: * Drawbar with 50 mm drawbar eye and height adjustment ----Lighting / Electrical: * EBS multi-voltage system with 12 & 24 V electrical system * 15-pole power connector * LED lighting system 12 / 24 V * LED rotating beacon (removable) at the rear * 2 LED reversing lights (switched via reverse gear) ----General attachments: * Manometer - pressure gauge for load weight determination (axles separated into 2 air suspension circuits) * Lateral impact guard Tjdpjl Tlhrofx Akcja * Swivel supports at the rear of the chassis frame * Mechanically adjustable warning sign packages at the front and rear * Front plastic quarter fenders with splash protection * Rear straight, galvanized steel splash guards with splash protection * Reflective contour strips on the sides and at the rear * Tool box made of galvanized steel sheet, black powder-coated, approx. 1,000 mm wide, 600 mm deep, 300 mm high ----Low-bed platform: * Extension in front of the turntable platform, approx. 490 mm long with 45° corners * ROBOTER welded anti-slip surface on the steel plate of the turntable platform * Hardwood flooring on the running surfaces of the low-bed platform ----Load securing (La-Si-package consisting of): * 1 x 13.4-ton UVV lashing eye on each side in front of the front bulkhead support * 4 holes on each side in the turntable platform, each with a lashing force of 2 tons * 1 pair of lashing eyes (13.4 tons) hanging at the rear on the left and right in front of the rear crossbeam * 4 pairs of UVV lashing rings (10 tons) on each side, swiveling and lowerable, loadable in all directions and recessed in the outer frame * 3 rung pockets on each side with simultaneous 2-ton lashing option ----Widening package: * Hot-dip galvanized mechanical folding outriggers for 3 m overall width (but not in the rear slope) * Beam holder for widening extensions under the chassis on the left in the longitudinal direction ----Excavator arm rest: * Excavator arm rest above the rear axle up to the end crossbeam, approx. 2,100 mm long and approx. 190 mm deep * 2 pairs of 6.4-ton lashing eyes on each side in the excavator arm rest ----Ramps: * Hydraulic, one-piece ramps (approx. 3,000 x 720 mm) mechanically adjustable on the sides * Outer beams of the ramps made of hardwood * Steel construction as preparation for a 6-way control valve ----Loading height: * Loading edge unladen approx. 950 mm +/- 20 mm ----Tires: * Tires 235/75 R 17.5 ----Paint: * Chassis, turntable, folding outriggers, mechanical support legs, ramps hot-dip galvanized * --Axles, air tanks, drawbar painted in a black tone-- ----Info: * Vehicle has a temporary registration in 07/2024, due to a missing tire pressure monitoring system and has not been loaded/used * New vehicle with manufacturer's warranty * Errors and prior sale are subject to change ----Delivery time: * Immediately available from Egestorf

Condition: new, maximum load weight: 8,870 kg, overall weight: 11,900 kg, axle configuration: 2 axles, loading space length: 6,270 mm, loading space width: 2,470 mm, loading space height: 400 mm, Year of construction: 2025, * ETÜ-TA-ER 11.9: Tedjl Thy Ropfx Akcoa ----Brake system: * Electronic braking system (EBS) * Emergency release device for spring-loaded cylinders * Drum brakes ----Axles: * 2 x 5.5 t Gigant axle system ----Suspension: * Parabolic leaf springs with equalizing aggregate ----Drawbar / Flange towing eye: * Height-adjustable drawbar, adjustable by 300 mm * 40 mm flange towing eye ----General attachments: * Jost mechanical support landing gear at the front * Rear external foldable support legs, hot-dip galvanized * Side underrun protection * Plastic quarter mudguards * Plastic toolbox mounted front-right on the bulkhead ----Electrics / Lighting: * TPMS (Tire Pressure Monitoring System) * 15-pin power connector * LED tail lights ----Loading area: * 50 mm softwood floor * 20" container locks fitted at front and rear * Front bulkhead bolted, made from smooth sheet metal * Drop sides made from trapezoidal-profiled steel, foldable with tailgate spring assist * Rear stanchions, hot-dip galvanized and bolted ----Load securing: * Perforated outer frame, approx. 45° edged, with 2 t lashing capacity every 480 mm * Optional installation of 3 t folding lashing brackets every 600 mm (each side fitted with 5 lashing rings) * One 6.3 t lashing ring in each front and rear corner * Various holes in the front and rear cross beams for 1.2 t lashing options ----Ramps: * 1 pair of aluminum approach ramps, approx. 3,310 x 400 mm (load capacity 8 t/pair), suitable for pneumatic-tyred and tracked vehicles * Rear stowage compartment beneath the loading platform, integrated in the chassis ----Paint/Coating: * Chassis, drawbar, front and rear bulkheads hot-dip galvanized * Side board color RAL 9010 pure white * Sides can be painted in any RAL color at extra cost ----Additional information: * New vehicle without registration * Subject to errors and prior sale ----Delivery time: * Immediately available ex Egestorf

Condition: new, maximum load weight: 10,800 kg, overall weight: 14,400 kg, axle configuration: 2 axles, loading space length: 6,270 mm, loading space width: 2,470 mm, Year of construction: 2026, * ETÜ-TA-R 14.4: ----Brakes: * EBS brake system * Emergency release device for spring-loaded brake cylinders * Drum brakes ----Axles: * 2 x 7 t Gigant axles ----Suspension: * Parabolic springs with compensating unit ----Drawbar / Flange Towing Eye: * Drawbar height-adjustable by 300 mm * Drawbar extension by 250 mm to a total length of 2,250 mm ----Electrics / Lighting: * Tire pressure monitoring system with in-cab display via EBS signal (no truck-side installation required) * 15-pin power connector * LED lighting system 12 / 24 V * EBS multi-voltage system for towing vehicles with 12 and 24 V electrics ----General Attachments: * Support winch at the front * External folding support legs at the rear * Plastic toolbox approx. 858 x 500 x 500 mm mounted front right on the bulkhead * Side underrun protection * Plastic quarter mudguards ----Low Loader Deck: * 50 mm softwood floor * Provision in front of the bulkhead for retrofitting container locks * Bolted 400 mm high smooth steel bulkhead * Bolted rear posts * Drop sides with spring assist ----Load Securing: * Perforated outer frame, approximately 45° angled, with 2 t lashing capacity every 480 mm * Option to install 3 t recessed lashings every 600 mm * One 6.3 t lashing ring in each front and rear corner * Various holes for 1.2 t lashing points in the front and rear crossmembers * Profifix lashing rail, centered lengthways, for lashing up to LC 3,000 daN ----Ramps: * One-piece hydraulic mesh loading ramps, approx. 2,750 x 600 mm (collapsible to 20 mm clearance) Tedpfxerwc R Rs Akcea * Hydraulic flow divider installed in trailer (for hydraulic pump flow from the truck exceeding 40 l/min up to max. 140 l/min) ----Paintwork: * Chassis, drawbar, bulkhead, mechanical folding supports, and loading ramps hot-dip galvanized * Axles, springs, air tanks, front support winch, and flange towing eye painted black * Drop side panels painted in RAL 9010 pure white * Painting of side panels in any RAL color available at extra cost ----Information: * New vehicle with manufacturer warranty * Subject to misprints and prior sale ----Delivery time: * Immediately available ex-works Egestorf

Condition: new, maximum load weight: 30,740 kg, overall weight: 40,000 kg, axle configuration: > 3 axles, Year of construction: 2026, * T 4: * Wabco EBS-E (electronic braking system) * RDÜ tire pressure monitoring system * Emergency release device for spring brake cylinders * Drum brakes * 4 x 11 t Gigant axles * Air suspension with lifting and lowering device and RtR valve * SmarD on-board system for load weight determination * Warning sign packages front & rear * Reflective contour tape on sides and rear * Removable rotating beacon at the rear * LED lights * Straight drawbar with 50 mm towing eye and infinitely adjustable height * Tool box made of powder-coated steel and spare wheel holder in basket design, mounted on the right side * Enclosed plastic single fenders at the front * Straight steel mudguards at the rear, each with spray suppression (anti-spray system) * Side underrun protection * Turntable platform extended by 520 mm with 45° corners and 3 integrated storage compartments incl. cover, lockable * Chassis made of high-strength fine-grained steel * Floor over turntable platform made of 50 mm softwood, in the low-bed platform made of 60 mm softwood * Outer planks of the loading ramps made of hardwood * 4 stake pockets on each side (no stakes included) with simultaneous 2 t lashing point per pocket Tjdpfx Akjl Tik Necoa * Load securing package consisting of: 2 lashing points 6.4 t at the front left and right on the main frame of the turntable platform * 2 pairs of 13.4 t lashing rings each at the outer frame front and rear, as well as 4 pairs of 10 t lashing rings per side, swiveling and retractable * Loadable in all directions and recessed into the outer frame * 2 pairs of 6.4 t lashing rings in the excavator arm rest area * 8 pairs of galvanized swing-out marker boards for 3 m total width (not at the rear slope) * Widening planks stored in a compartment on the left side * Excavator arm rest above rear axle up to end of approach ramp approx. 2,100 x 740 x 190 mm * Mechanical drop-down supports at the rear * Hydraulic folding ramps with hydraulically adjustable tip, approx. 4,650 x 720 mm incl. hydraulic lateral ramp shifting and load-holding valve * Loading area across the turntable: approx. 2,990 x 2,520 mm * Rear loading area: approx. 6,780 x 2,520 mm * Loading height loaded: approx. 890 mm, +/- 20 mm (incl. 860 mm approach slope) * Flow divider installed * Chassis, turntable, access ramps, flip-out marker boards and mechanical drop-down supports hot-dip galvanized * Axles, drawbar, air tanks, and turntable painted in black * Tires: 235/75 R 17.5 * New vehicle without first registration, with manufacturer warranty * Subject to errors and prior sale * Immediately available ex Egestorf on the A7

Condition: new, maximum load weight: 10,900 kg, overall weight: 14,400 kg, axle configuration: 2 axles, loading space length: 6,270 mm, loading space width: 2,470 mm, loading space height: 400 mm, Year of construction: 2025, ETÜ-TA-R 14.4 ----Braking system: * EBS electronic braking system * Emergency release mechanism for spring brake cylinders * Drum brakes ----Axles: * 2 x 7 t Gigant axles ----Suspension: * Air suspension ----Tow bar / Flange eye: * Tow bar height-adjustable by 300 mm * Tow bar extension by 250 mm to 2,250 mm * 40 mm flange towing eye Tedpfx Asq Dyvyskcsa ----Lighting / Electrics: * RDÜ (tyre pressure monitoring system) * LED tail lights 12 / 24 V * 15-pin power connector ----General attachments: * Jost landing gear front * Externally mounted, hot-dip galvanized folding supports at rear * Plastic toolbox, front right, mounted on the bulkhead * Side underrun protection * Plastic quarter mudguards ----Low loader platform: * 50 mm softwood floor * Fittings in front of bulkhead for retrofitting container locks * Bolted flat sheet steel bulkhead * Drop sides made of trapezoidal-profiled steel sheet, folding with drop side lifting springs * Rear steel wall retractable between ramp holders, stowable in front of bulkhead when not in use * Bolted rear stanchions * Rear drive-on slope approx. 860 mm ----Load securing: * Perforated outer frame, approx. 45° angled, with 2 t lashing force every 480 mm * Option to install 3 t folding lashing brackets every 600 mm * 1 x 6.3 t lashing ring in each front and rear corner * Various drillings for 1.2 t lashing points in front bulkhead and rear end crossmember ----Ramps: * One-piece, mechanical mesh ramps with spring assist for single-person operation, approx. 2,750 x 600 mm (collapsible to 20 mm) ----Paintwork: * Hot-dip galvanized chassis as well as tow bar, bulkhead, tailgate, and access ramps * Sideboard colour in RAL 9010 pure white * Painting of side walls in alternative RAL colours available at extra cost ----Info: * --Reinforced and certified body built according to EN 12642 XL including load securing certificate-- * New vehicle with manufacturer’s warranty * Subject to errors and prior sale ----Delivery time: * Available immediately ex Egestorf

Condition: new, maximum load weight: 20,500 kg, overall weight: 27,000 kg, axle configuration: 3 axles, loading space length: 7,000 mm, loading space width: 2,470 mm, Year of construction: 2026, * ETÜ-TR 27.0 Platform: * EBS (Electronic Braking System) * Emergency release device for spring brake cylinders * Drum brakes * 3 x 9 t BPW Eco axles * Air suspension with lifting and lowering system, with RTR function * 1st axle liftable * Last axle as follower steering axle with electro-pneumatic steering lock via PIN reverse gear (locking of the follower axle from the tractor unit for maneuvering purposes - without truck-side installation - assigned to PIN 10 in the 15-pin connector, for maneuvering purposes only, not for use in public road traffic) * SmartBoard control unit as an infotool, with pressure sensors for total axle load display * Tire pressure monitoring with display option in the truck via EBS signal, no truck-side installation required * Fixed central drawbar with 50 mm flanged towing eye (loaded 900 mm, height adjustment at the head board) * Mechanical landing gear at the front, mechanical swing-down supports at the rear of the chassis * Hydraulic flow divider * Continuous side walls (without center posts) up to the run-on ramp * Rear stanchions foldable * Steel rear wall inserted in front of the rear stanchions * Mechanically adjustable warning sign package at front and rear * Tool boxes made of galvanized sheet steel - black powder coated - approx. 650 x 300 x 600 mm, mounted right side * 15-pin power connector * LED tail lights * Detachable LED rotating beacon incl. bracket and installation * 2 x LED reverse lights at vehicle rear (activated via reverse gear) * Flashing LED side marker lights * 60 mm larch / douglas fir wood floor * 400 mm plug-in steel front wall * Perforated outer frame, approx. 45° angled, with provisions for mounting 3 t folding lashing brackets * In each corner 1 x 10 t lashing ring, as well as 2 x 10 t and 3 x 6.3 t lashing rings per side additionally Tedpfxer Dpzxs Akcsa * Various holes in the front and rear cross members for 1.2 t lashing options * Hydraulic one-piece drive-on ramps, approx. 3,000 x 720 mm, mechanically adjustable sideways * 4-way hydraulic control block for possible retrofit of hydraulic ramp shifting * Chassis, drawbar, front wall, rear manual supports, and drive-on ramps hot-dip galvanized * Axles, air tanks, flanged drawbar eye, and front mechanical landing gear coated in black * Hydraulic flow divider in the trailer (for hydraulic pump output from 40 l to 120 l/min in the truck) * New vehicle with manufacturer’s warranty * Errors and prior sale excepted * Immediately available from Egestorf

Condition: new, maximum load weight: 10,360 kg, overall weight: 14,400 kg, axle configuration: 2 axles, loading space length: 6,270 mm, loading space width: 2,470 mm, loading space height: 400 mm, Year of construction: 2025, * ETÜ-TA-ER 14.4: ----Brakes: * Electronic braking system (EBS) * Emergency release device for spring-loaded cylinders * Drum brakes ----Axles: * GIGANT axles ----Suspension: * Air suspension with lift and lowering system ----Drawbar / Flange drawbar eye: * Height-adjustable drawbar (adjustable by 300 mm) * 40 mm flange drawbar eye Tedpfx Aopk D Dqokcea ----Electrics / Lighting: * TPMS (Tire Pressure Monitoring System with display option in the truck via EBS signal—no truck-side installation required) * LED lighting system * 15-pin power connector ----General attachments: * Jost landing gear at the front * Externally mounted, hot-dip galvanized folding support legs at the rear * Plastic toolbox mounted on the front wall, right-hand side * Side underrun protection * Plastic quarter mudguards ----Lowbed platform: * 50 mm softwood floor * Preparation for subsequent installation of 20" container locks at the front and rear * Bolted front wall, smooth sheet steel * Drop sides made of trapezoidal-profile sheet steel, foldable with sideboard spring assist * Bolted, hot-dip galvanized rear stakes ----Load securing: * Perforated outer frame, approx. 45° angled, with 2 t lashing capacity every 480 mm * Option to fit 3 t folding lashing rings every 600 mm * One 6.3 t lashing point at each front and rear corner * Various holes in the front wall and end crossmember for 1.2 t lashing options ----Ramps: * 1 pair of aluminum loading ramps approx. 3,310 x 400 mm (load capacity 8 t per pair), suitable for rubber-tired and tracked vehicles; storage compartment underneath the loading platform integrated in the chassis for rear access ----Paintwork: * Chassis, drawbar, front wall, and rear wall hot-dip galvanized * Entire vehicle hot-dip galvanized ----Info: * New vehicle with manufacturer's warranty * Errors and prior sale excepted ----Delivery time: * Immediately available ex Egestorf

Condition: used, maximum load weight: 12,100 kg, overall weight: 16,000 kg, axle configuration: 2 axles, first registration: 01/2011, loading space length: 7,400 mm, loading space width: 2,500 mm, Equipment: ABS, * ABS * Orange rotating beacon * Duomatic air connection * 5-chamber rear lights * Front support winch * BPW ECO axles ----Structure: Open platform (loading height approx. 950 mm), hardwood floor, extendable by 1,685 mm at the rear, 4 extendable container locking pairs (Twist Lock), stainless steel storage boxes. Tedpfjvy Nw Tox Akcsa Only sold to traders. ONLY THE NET PRICE IS PAYABLE FOR EXPORT !!!!! ALL INFORMATION IS PROVIDED WITHOUT GUARANTEE FOR EQUIPMENT + ACCESSORIES. Our general terms and conditions form the basis of all purchase contracts, invoices, pro forma invoices, orders and sales talks (see legal notice).

Condition: used, overall weight: 3,500 kg, axle configuration: 1 axle, first registration: 09/1996, Year of construction: 1996, Equipment: crane, * Technical Specifications * Name: DENKA LIFT MK 25 * Clemens AB 25 meter Working height: 25.00 m / 200 kg Basket load capacity: 200 kg / 2 persons Slew range: 360° continuous Outreach: 11.40 m / 80 kg Outreach: 9.00 m / 200 kg Own weight: 2,450 kg Platform size: 0.70 x 1.40 m Passage width: 1.69 m Passage height: 2.11 m Overall length: 9.07 m Minimum length: 8.30 m * Outrigger footprint: 3.90 x 3.90 m * Features - 24V battery drive with built-in automatic charger - Hydraulic quick outrigger system - Second control panel on chassis - 230 V socket and tool tray in platform - Jib arm with rotating platform - Manual emergency operation - Safety system for outrigger legs and overload - Infinitely variable proportional control * Operating hours: Mon to Fri 07:30-12:00, 13:00-18:00, Saturday 07:30-17:00 * Email: Tjdpfjxzw Hzex Akcsa * Tel/ WhatsApp/ Viber: Alexandar Ilic * Tel/ WhatsApp/ Viber (English): Mladen Ilic

Condition: new, overall weight: 3,500 kg, loading space length: 6,200 mm, loading space width: 2,100 mm, tire size: 13, Year of construction: 2025, ANHÄNGERWIRTZ – your pick-up market for new trailers presents top brand models! Over 850 new trailers in stock Over 130 used trailers constantly available. Tjdpfxjy Hrgpj Akcoa Non-binding sample offer: Variant machine transporter Variant Multitransporter 3563 UX 620x210x30 cm, 3800 kg, braked, tandem axle, high loader, low chassis, 13" wheels, tilting flatbed with manual hydraulic pump, 30 cm fold-down aluminum side panels, continuous loading ramp 90 cm high with lift assist, DIN lashing rings on the chassis edge, automatic jockey wheel, modern LED lighting... Available in various lengths and configurations. Our trailer shop offers you the unique Roadster at a fair price with short delivery times. New vehicle, invoice with VAT shown, warranty from a specialist dealer with 35 years of experience. Copyright images, text, logos 04.2026 VDK-3563UX30BLACK

Condition: new, maximum load weight: 30,080 kg, overall weight: 40,000 kg, axle configuration: > 3 axles, Year of construction: 2026, * T4 RM 40.0: * Wabco EBS-E (electronic braking system) * Emergency release device for spring brake cylinders * Tire pressure monitoring with display capability in the truck via EBS signal (no truck-side installation required) * Drum brakes * 4 x 11 ton Gigant axles * Air suspension with manual lowering at the rear * Warning sign packages front & rear * SmartBord infotool mounted with pressure sensors for total axle load display per axle group * Side and rear reflective contour tape * Removable LED beacon at the rear * 15-pin power connector * LED tail lights * Straight drawbar with 50 mm towing eye and stepless height adjustment * Closed single plastic mudguards at the front * Straight rear steel mud flaps each with spray suppression * Side underrun protection * Front extension in front of turntable platform approx. 520 mm with 45° corners and 3 storage compartments incl. lockable folding lids (open to the rear) * Chassis made of high-strength fine-grain steel * Floor above turntable platform made of 50 mm softwood and 60 mm softwood on low-bed platform * Outer planks of the ramps made of 50 mm hardwood * Load securing package consisting of: 2 lashing eyes 6.4 t front left and right on the main frame of the turntable platform; one pair each (front & rear) of 13.4 t lashing rings on the outer frame; one pair each side of 10 t swivel and lowerable lashing rings, loadable in all directions and integrated in the outer frame; bolted 5 t lashing rings on the outer frames of the wheel wells (2 at the front wheel well, 1 at the rear); 2 pairs of 6.4 t lashing rings at the sides of the excavator boom cradle * 11 pairs of folding outriggers for a total width of 3 meters (not on rear slope) * Storage compartment (L = 2,470 x W = 570 x H = 250 mm) for widening planks made of sheet steel, mounted transverse to the load area in front of the 1st rear axle * Excavator boom cradle above the rear axle to end of incline approx. 2,300 x 740 x 190 mm * 2 wheel wells per side, approx. 640 mm wide – front 340 mm deep, rear 220 mm deep – with sliding cover (storage for covers at the front on the turntable platform) for transporting wheel loaders with 3,100 - 3,640 mm wheelbase Tedpfx Aoxmpydjkcoa * Mechanical drop-down supports at the rear * Hydraulic folding ramps with hydraulically deployable tip section approx. 4,650 x 720 mm * Hydraulic lateral ramp shift * Loading area above fifth wheel: approx. 2,990 x 2,520 mm * Rear loading area: approx. 6,780 x 2,520 mm, loaded height approx. 890 mm +/- 20 mm (incl. 860 mm approach slope) * Chassis, turntable, folding outriggers, rear supports, and ramps hot-dip galvanized * Axles, air tanks, and drawbar painted black * Tires: 235/75R17.5 * Vehicle is hot-dip galvanized * New vehicle with manufacturer warranty * Subject to change and prior sale * Immediately available ex Egestorf

Condition: new, maximum load weight: 19,470 kg, overall weight: 24,000 kg, axle configuration: 3 axles, loading space length: 8,600 mm, loading space width: 2,500 mm, loading space height: 930 mm, Year of construction: 2026, Equipment: ABS, Now immediately available!!!!! JUMBO PLATFORM TRAILER KRONE 3-axle ADP 27/ zLNT4 BS / MULTILOCK/8600 mm/BPW Manufacturer: KRONE Registration date: NEW VEHICLE Dimensions: 8600 x 2480 x 930 Permissible total weight: 24000 kg Unladen weight: 4420 kg Payload: 19580 kg Air suspension, raise/lower function Todsy U R T Repfx Akcea Drum brakes Spare wheel holder ABS EBS Axle manufacturer: BPW ECO Screen-printed floor Tie-down points Toolbox Paintwork, body: black Paintwork, chassis: black Tires: 12 Tire condition: 100% Tires, front axle: 235/75 R 17.5 Tires, rear axle: 235/75 R 17.5 MULTILOCK OUTER FRAME along the entire length BPW eco drum brake, 3 x 9000 kg axle RETRACTABLE DRAWBAR 2000 - 2400 mm Air suspension, raise/lower function, front and rear Technically, maximum permissible total weight of 27000 kg ABS/EBS system 30 mm screen-printed floor Forklift-compatible with 5460 kg axle load STEEL FRONT WALL 1200 mm high Wheelbase 8545 mm / axle distance 2nd - 3rd axle: 1310 mm Overall length 10390 mm 880 mm lowered All information without guarantee, subject to prior sale!! If you have any questions about this or other vehicles, please call us.

Condition: as good as new (ex-display), machine/vehicle number: AHW MT3080, overall weight: 3,000 kg, loading space length: 3,080 mm, loading space width: 1,520 mm, ANHÄNGERWIRTZ: The Online Pickup Market for Your New Trailer—offering top brand models ready to go! - Over 850 new trailers in stock - Over 100 used trailers always available - Over 150 vehicle transporters in popular configurations with extensive accessories in stock Non-binding example: exhibition trailer ready for pickup: Todpfxeyrbnfs Akcoa Brenderup Machine Transporter MT 3080 GD, 308x152cm, 3000kg, low-loader with tandem axle and V-drawbar, rear ramp as a tailgate with support leg 13-pin plastic connector, 14-inch tires Jockey wheel, 6 internal lashing eyes / 400 daN Excavator bucket holder Non-slip fender coating and step Hot-dip galvanized, high-quality, robust anti-slip plywood floor Sturdy metal wheel chocks, position lighting Recessed lights Spare wheel including bracket under the bucket holder The largest selection of transporters available immediately Sales: telephone orders accepted during the day, or 24/7 via our trailer shop Images and descriptions of this advert are protected by copyright—logos are trademark protected. 03/26 39033

Condition: used, Has TÜV and valid UVV an invoice including VAT will be issued VAT is deductible Tedpfxsy A Rats Akcoa will only be handed over deregistered

Condition: new, empty load weight: 614 kg, maximum load weight: 2,886 kg, overall weight: 3,500 kg, axle configuration: 2 axles, loading space length: 2,800 mm, loading space width: 1,300 mm, loading space height: 200 mm, loading space volume: 0.7 m³, color: silver, construction height: 1,970 mm, working width: 1,790 mm, Automatic reverse drive, hot-dip galvanizing, extremely sturdy superstructure, perforated lashing floor, LED lighting, e-wheel, bucket storage, * IMMEDIATELY AVAILABLE * extremely sturdy superstructure / perforated lashing floor / LED lighting / e-wheel / bucket storage TECHNICAL DATA - Make: Brian James - Model: Digger Plant 2 - Vehicle type: Construction machinery - Vehicle condition: New vehicle - Initial registration: Without initial registration - TÜV/HU: 2 years from initial registration - Internal dimensions (LxWxH): 280 x 130 x 20 cm - External dimensions (LxWxH): 465 x 179 x 197 cm - Loading height of floor: 38 cm - Perm. Gross weight: 3,500 kg - Unladen weight: 614 kg - Payload: 2.886 kg - Chassis: Low loader (wheels next to the body) - Tyres: 165R13C - Chassis: ALKO rubber spring axle - Support wheel: Yes - 100 km/h approval: Optional, can be retrofitted DESCRIPTION - Robust steel mudguards with non-slip perforated profile - Reinforced perforated steel floor inside on the side - 18 mm screen-printed wooden floor in the middle, non-slip and waterproof - Very sturdy welded steel frame - Frame completely hot-dip galvanized - Chassis: Steel frame with anti-slip profile hot-dip galvanized - chassis with two additional longitudinal beams under the loading area - perforated steel single ramps, galvanized steel, adjustable, L=1.62m - stable ACME locking system: closes silently, loading ramps are held in place by safety clamp locks, Rubber buffer dampens noise - Very low chassis for low drive-on angle - Excavator bucket storage - 10x lashing eyelets on the dropside (1000dAN/kg) TÜV certified - Free choice of lashing points for lashing in the perforated steel floor - Maintenance-free axles and damping systems designed for long journeys and heavy loads - Spare wheel mounted on the side wall for easy access - Automatic reverse drive - ALKO overrun device and parking brake - Cast steel coupling head with integrated ALKO high-security lock - Very sturdy V-drawbar RENFORCED - 13-pin plug - Complete LED lighting system Plug - Complete LED lighting: Extremely bright, durable and reliable. - Reversing lights - Integrated rear fog light - Robust protection for rear lights - Heavy-duty support wheel - 5-year chassis warranty Accessories can be retrofitted - please enquire! - TracStrap load securing system - excavator bucket cage - lashing straps - storage box - winch - and much more New vehicle with warranty and TÜV. We are happy to offer you suitable financing !, Descriptions and pictures are protected by copyright !!! Over 800 trailers immediately available for you! We are for over 30 years Brian James / Humbaur / Hapert / Unsinn / Cheval Liberte / Koch / Debon / Stedele / TPV / Tohaco / Vezeko / Variant / Vlemmix - specialized dealer & repair - workshop - delivery Germany-wide with surcharge possible! Anhänger Zentrum BAUMANN GmbH Dinxperloer Str. 389 46399 Bocholt - Errors, omissions and prior sale excepted - Tsdpsu Hrg Uofx Akcja

Condition: new, maximum load weight: 11,400 kg, overall weight: 15,000 kg, axle configuration: 3 axles, loading space length: 12,000 mm, loading space width: 2,480 mm, loading space height: 850 mm, total width: 2,550 mm, Year of construction: 2026, Metal-Fach T009 Bale Transport Trailer 3-axle flatbed trailer Platform trailer New vehicle Year of manufacture: 2026 Overall dimensions: 11,990 mm + 800 mm x 2,480 mm x 2,900 mm Internal dimensions: 9,300 mm + 800 mm x 2,380 mm x 1,875 mm Gross weight: 15,000 kg Unladen weight: 3,560 kg Payload: 11,440 kg Loading height: 1,160 mm Tedpfetw N D Sex Akcoa Tyres: 500/50-17 Extendable loading area Wide tyres Air-braked ALB regulator Side underride guard Side lighting Parabolic suspension Parking brake Adjustable front and rear load guard Y-drawbar Approval possible for 40 km/h Mudguards Custom painting available !!! ATTENTION – PLEASE READ CAREFULLY !!! We expressly reserve the right to prior sale, as this item is also advertised on other platforms. We strongly recommend a viewing and inspection to avoid misunderstandings regarding the condition and suitability for your needs. Viewings and inspections are possible at any time by appointment and are strongly encouraged!!! Images are for reference only and may show optional, chargeable accessories. All internal dimensions are approximate. TRADE-INS POSSIBLE FOR ALMOST EVERYTHING!!! PART-EXCHANGE AND TOP-UP DEALS POSSIBLE!!! Showground: 58285 Gevelsberg, Am Sinnerhoop 17 Opening hours: Monday to Friday 8:30 am to 5:00 pm, Saturday 8:30 am to 2:00 pm Over 500 new and used trailers in stock at all times!!! Pegasus Anhänger GmbH Am Sinnerhoop 17 58285 Gevelsberg Tel.: Fax:

Condition: new, maximum load weight: 9,000 kg, overall weight: 11,600 kg, axle configuration: 2 axles, loading space length: 9,080 mm, loading space width: 2,520 mm, loading space height: 850 mm, total width: 2,550 mm, Year of construction: 2026, Metal-Fach T014/2 Bale Wagon 2-Axle Platform Trailer Flatbed Trailer New Vehicle Year of Manufacture: 2026 Overall Dimensions: 9089mm + 800mm x 2520mm x 2880mm Internal Dimensions: 6409mm + 800mm x 2380mm Loading Height: 1150mm GVW (Gross Vehicle Weight): 11600kg Unladen Weight: 2600kg Payload: 9000kg Tires: 400/60-15.5 Extendable Loading Platform Wide Tires Air Pressure Brakes ALB Controller Lateral Underrun Protection Side Lighting Parabolic Suspension Parking Brake Adjustable Loading Grille at Front and Rear Y-Drawbar 40 km/h Approval Possible Fenders Custom Paint Possible Tedohlr Rdopfx Akcoa ATTENTION!!!!! PLEASE READ!!!!! We expressly reserve the right of prior sale, as we offer this item on other platforms as well. We strongly recommend an inspection and verification to avoid any misunderstandings regarding the condition and suitability for the buyer. Inspections and verifications are possible and expressly desired at any time after prior arrangement!!! Illustrations are similar and may include optional accessories that incur extra costs. The stated internal dimensions are approximate. TRADE-INS POSSIBLE FOR ALMOST ANYTHING!!! EXCHANGE DEALS AND PAYMENT PLANS POSSIBLE!!! Exhibition grounds: 58285 Gevelsberg, Am Sinnerhoop 17 Opening hours: Monday to Friday, 8:30 a.m. to 5:00 p.m., Saturday, 8:30 a.m. to 2:00 p.m. Constantly over 500 new and used trailers in stock!!! Pegasus Anhänger GmbH Am Sinnerhoop 17 58285 Gevelsberg Tel.: Fax:

Condition: new, overall weight: 1,500 kg, axle configuration: 1 axle, loading space length: 3,750 mm, loading space width: 2,200 mm, loading space height: 2,300 mm, Exhibition Trailer Event Promotion HBA375 Please use 0566 for inquiries.* Permissible total weight: 1,500 kg * Internal dimensions: 375x220x230 cm * Chassis: single-axle high loader, steel/galvanized with 4 extendable support legs * Tires: 10 inch * Reverse-automated brake and jockey wheel * 13-pin plug connector * Body: white, UV-resistant polyester sandwich panels, white painted profile strips * Walls and ceiling approx. 25 mm thick * Full-length fold-down flap on the right in the direction of travel * Folding aluminum steps with insertable handrails/railings on both sides; flag holders included Additional €39 gross for vehicle documents/COC. We will send these by registered mail after receiving a (down) payment or hand them over to you in person. Please arrange a viewing in advance, as this vehicle may be sold despite our large stock on site. You can call us to check if your desired trailer is available immediately—we are also happy to order new trailers with different details (dimensions, weight, equipment, etc.) to your specifications. Due to the large number of trailers in stock, errors may occur from time to time—please bear with us. All details and prices subject to error. Tedpfx Akoxw Dt Tscja

Condition: new, maximum load weight: 2,110 kg, overall weight: 2,700 kg, axle configuration: 2 axles, loading space length: 3,050 mm, loading space width: 1,550 mm, loading space height: 200 mm, B27300/150 MACHINE TRANSPORTER TECHNICAL DATA * Trailer type B27300/150 * Total weight 2700kg * Payload 2075kg * Internal dimensions L: 305cm, W: 155cm, H: 20cm * Loading height approx. 54 cm * Floor multiplex wooden floor * Lashing points recessed in the loading floor * Side walls steel * Frame welded steel, hot-dip galvanized * Electrics 13-pin, 12V * Tires 185R14C * Axle manufacturer AL-KO or KNOTT * Number of axles 2 * Braked axle Tsdothlrhepfx Akcsa * Support wheel as standard * Walkable steel fenders * Shovel storage * Rear supports * Loading ramps - 200 cm plus vehicle registration document/ COC certificate 39.00 ¤ All prices include VAT. Images do not have to correspond to the standard equipment, technical changes (e.g. tire sizes) are subject to change. Delivery: Delivery by freight forwarder possible, per transport kilometer ¤ 1.50 throughout Germany one way (Seesen to destination) at least 270¤ plus VAT Visit us at =.=.=.=.=.=.=.=.=.=.=.=.=.=.=.=.=.=.=.=.=.=.=.=.=.=.=.=.=.=.=. =.=.=.=.=.=. You can also get your desired trailer and accessories here by arrangement: B L Y S S transporttechnik GmbH Dieselstr. 8 85084 Reichertshofen Tel.: .:.:.:.:.:.:.:.:.:.:.:.:.:.:.:.:.:.:.:.:.:.:.:.:.:.:.:.:.:.:.:.: .:.:.:.:.:.:.:.:.:.:.:.:.:.:.: B L Y S S transporttechnik GmbH Burenkamp 18-20 46286 Dorsten - Wulfen Tel =.=.=.=.=.=.=.=.=.=.=.=.=.=.=.=.=.=.=.=.=.=.=.=.=.=.=.=.=.=.=. =.=.=.=.=.=.=. ?FINANCE OR LEASING POSSIBLE* Vehicle number (for customer inquiries) Images do not necessarily correspond to the standard equipment, technical changes (e.g. tire sizes) are subject to change.