Trailer with working platform

MÜLLER-MITTELTAL T3 Tiefl., verz., Baggerstiel, hydr. Klapprampen

Condition: new, maximum load weight: 23,500 kg, overall weight: 30,000 kg, axle configuration: 3 axles, Year of construction: 2026, Equipment: ABS, * T 3: * ABS braking system * Emergency release device for spring-loaded cylinders * Drum brakes * 3 x 11 t BPW Eco axles * Parabolic springs * Mechanical axle equalization at the rear * Side underrun protection * Pivoting supports at the rear of the chassis frame * Mechanically adjustable warning sign kits at front and rear * Front axle: enclosed plastic mudguards; rear axle: straight, galvanized steel skirts, each with splash guards * Reflective contour tape on sides and rear * Hinged lid (hot-dip galvanized) for toolbox on the bogie platform * Toolbox made of galvanized sheet steel, approx. 650 x 300 x 600 mm – powder-coated in black – located at the side beneath the chassis * 15-pin electrical connector Godpfjtplwfox Aa Seua * LED lighting 12 / 24 V * Rear LED beacon (removable) * Towing bar with 40 mm towing eye and height-adjustment via tension spring and turnbuckle * Four stake pockets per side (stakes not included), also suitable for lashing * Load securing package including: 2 lashing eyes (6.4 t) front left & right on the main frame of the bogie platform * 5 pairs of UVV-compliant lashing rings, swiveling and retractable * Loadable in all directions and flush-mounted in the corners of the outer frame: 13.4 t in the corners, otherwise 10 t * 6 pairs of mechanical folding outriggers for 3 m overall width (but not in the rear slant) * Widening planks stored in a compartment beneath the loading area * Excavator arm rest above rear axle up to end cross member, approx. 2,100 mm long (2 pairs of 6.4 t lashing rings on the sides of the excavator arm rest) * Hydraulic folding ramps (approx. 4,650 x 720 mm) with hydraulically extendable tip section and load-holding valves, hydraulic lateral ramp shift * Hydraulic flow divider in the trailer (for hydraulic pump capacities in truck over 40 l up to max. 140 l / min), dual-line hydraulics * Loading area above bogie: approx. 1,960 x 2,520 mm * Rear loading area: approx. 6,500 x 2,520 mm (including 860 mm drive-up slant) * Loaded platform height approx. 860 mm +/- 30 mm balance unit * Chassis, bogie, folding outriggers, drop-down supports rear, and ramps hot-dip galvanized * Axles, springs, towing bar, air tanks etc. painted in black shade * New vehicle with manufacturer warranty * Errors and prior sale excepted * Available from calendar week 19/2026

Condition: new, machine/vehicle number: 2dff0c136c85096f36822a0bb, empty load weight: 7,150 kg, maximum load weight: 16,850 kg, overall weight: 24,000 kg, axle configuration: 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction Turntable with strong ball bearing slewing ring, storage box embedded in turntable front end Folding rear support 2 wheel chocks with holder Aluminum side collision protection Rear spray flaps across the entire width Widenings can be extended to 3,000 mm (not in the rear slope) (However, the track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Storage compartment for wooden planks in the middle of the cargo bed Wooden planks 70 mm for widening to 3000 mm Low loader lashing eyes 3 pairs of lashing points each 10 to integrated in the floor at the front 6 pairs of lashing points at the top and sides, each 10 tons, integrated in the outer frame 1 x to the neck area remaining distributed in between Spacing not greater than 1200 mm 1 x rear slope 5 pairs of stake pockets embedded in the outer frame, inside 70 x 40 mm, (can be converted to 5 to. ring lashing eyes, not included in the scope of delivery) Towing equipment Trailer turntable Drawbar with tested 40 mm drawbar eye Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation axle load compensation (rocker compensation) Brake system 2-line compressed air brake system Colored line routing for easy servicing. Spring-loaded parking brake Incl. 2 swap-proof coupling heads at the front, with connecting lines to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable, Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Wheels and tires 235 / 75 R 17,5 at the choice of the manufacturer Steel rims in twin arrangement, factory silver Electrical system 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin interchangeable plugs at the front, with connecting cable, 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Front area steel floor, then with 70 mm softwood floor, steel/checker plate flooring in the wheel housing area Rear slope with 70 mm softwood floor Deep loading area incl. rear slope 8,200 mm Drive-on ramps Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways Covered with wood Incl. with spring lift support Operating instructions With an axle load of 10,000 kg, a special permit is required, only indivisible loads possible!!! The specified total weight is technically possible; depending on the load, the total weight may not be achieved while complying with the permissible axle/support and fifth-wheel loads. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Godoi Riy Eepfx Aa Seua Country of registration: Germany with Dekra approval and expert opinion (according to §13 EG - FGV) 24/7 service hotline Prepared for two-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white on the sides and red on the rear Paint finish Frame DB 7350 nova gray 10-year warranty against rusting through Drawbar Galvanized or black, at the manufacturer's choice Drive-on ramps Hot-dip galvanized Attention: Archive pictures!

Condition: new, maximum load weight: 16,400 kg, overall weight: 30,000 kg, axle configuration: 3 axles, Year of construction: 2024, * T3 Profile 30.0: * EBS-E (electronic braking system) * TPMS (tire pressure monitoring system) * Emergency release device for spring-loaded cylinders * Drum brakes * 3 x 11 t BPW Eco axles * Air suspension with lifting and lowering function * SmartBoard as infotool on the trailer, with pressure sensors for indicating total axle load per axle group * Side underrun protection * Mechanically adjustable warning sign sets at front and rear * Front axle closed plastic mudguards; rear axle straight galvanized steel skirts, both with splash guards * Folding lid (hot-dip galvanized) for the toolbox on the turntable platform * Toolbox made of galvanized steel sheet, approx. 650 x 300 x 600 mm (black powder-coated), mounted on right side * 15-pin electrical connector * LED lighting 12 / 24 V * Removable LED beacon at rear * Side marker lights with indicator control * Drawbar with 40 mm towing eye and height adjustment via draw spring and turnbuckle * Tire pressure monitoring system with display option inside truck via EBS signal (without installation on the truck side) * Rubber covering on the folding ramps and loading slope left and right (approx. 860 mm long) * Rubber covering on the longitudinal beams from front end to rear end * Hardwood flooring on running surfaces of the low-bed platform Gedpfx Ajtplv Nja Soua * 4 stake pockets per side, each with 2 t lashing capacity * Load securing package consisting of: 5 pairs of UVV lashing rings, swingable and lowerable, loadable in all directions and embedded in the outer frame – 13.4 t capacity in the corners, otherwise 10 t * 6 pairs mechanical fold-out outriggers for 3 m total width (excluding the rear slope) * Plank holder under the loading area, longitudinally mounted * Roller stops raised in front of the front wall, with 1 x 6.4 t lashing eye each side * Hydraulic folding ramps (approx. 4,650 x 720 mm) with hydraulically extendable ramp tip and load-holding valves * Hydraulic lateral ramp adjustment * Rear hydraulic support (single-stage cylinder) * Hydraulic flow divider in trailer (for hydraulic pump capacity in truck from over 40 l/min up to max. 140 l/min) * Splash-proof hydraulic control block * Two-line hydraulic system * Loading area over turntable: approx. 1,960 x 2,520 mm * Rear loading area: approx. 6,500 x 2,520 mm (including 860 mm loading slope) * Loaded platform height approx. 890 mm +/- 20 mm air suspension * Chassis, turntable, roller stops, fold-out extensions & ramps hot-dip galvanized * Axles, turntable, drawbar, air tanks etc. painted in black * Loaded platform height: approx. 890 mm +/- 20 mm * New vehicle with manufacturer's warranty * Subject to errors and prior sale * Available from CW 20/2026