Used Other Semitrailers With Work Platform for sale (114)

Condition: new, maximum load weight: 38,400 kg, overall weight: 48,000 kg, axle configuration: 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory, including immediately and short-term available vehicles, on our website. Excerpt from the specifications. Full specification available on request. Loading area: * Extendable loading platform with pneumatically operated locking mechanism * Loading area with approx. 30 mm thick wooden planks * 7 pairs of outward-folding lashing rings (LC 5,000 daN) * 3 pairs of outward-folding lashing rings (LC 10,000 daN) * Cut-outs in the outer frame of the platform for hooking in tension straps (LC 2,000 daN) Landing legs: * JOST mechanical landing legs with 2-speed gearbox, approx. 24 t lifting capacity (approx. 50 t test load) Tyres: * Tyres: 385/65 R 22.5, manufacturer at our discretion * TPMS tyre pressure monitoring system in accordance with ECE R 141. Data transmission to the truck is via the standardized EBS interface as per ISO 11992. For proper display, the truck must be capable of receiving and showing this data. Axle: * BPW axles and suspension * All axles hydromechanically forced-steered * Disc brakes * Technical axle load: 10,000 kg each (offset 0) * Air suspension with raise/lower valve * Axle tools Brake system: * WABCO brake system in accordance with EU regulations, EBS-E (2S2M) without connection lines to the tractor unit Steel construction: * High-strength fine-grain steel construction * Steel grades: S355J2+N/S355MC (yield strength 355 MPa), S690QL/S700MC (yield strength 690 MPa) Electrical system: * Electrical system in accordance with EU regulations * LED lighting 24 Volt ASPÖCK-NORDIK (ASS3) * All LED side marker lights flash together with indicators * ASPÖCK-UNIBOX at the front connection bar with 24N, 24S, and 15-pin sockets according to ISO: 24N ISO-1185, 24S ISO-3731, 15-pin ISO-12098 Paintwork: * Complete steel structure automatically shot-blasted after welding * Second blasting with corundum for optimal coating adhesion * Final painting with two coats of 2-component topcoat, single color, RAL 3002 Carmine Red according to RAL system 841GL * Rims in silver grey * Rear section metallized and painted RAL 9010 (Pure White) * Metallic paint not available * Paint finish tested in salt spray test according to ISO 9227-NSS * Cavity sealing with special wax Todpjw Tpr Ijfx Agbjd Accessories: * Remote steering from front and rear via cable remote control with push buttons, with axle tracking monitoring (without installation in the tractor unit) * Electro-hydraulic unit * 4 wheel chocks with holders on the front wall * 2" kingpin * Yellow-red air couplings at the galvanized front connection bar * At gooseneck and rear, left and right, brackets for warning panels, including sockets * 10 pairs of stake pockets for approx. 100 x 50 mm plug-in stakes in the external frame of the loading platform * One galvanized steel front wall (EN12642-XL), approx. 1,600 mm high * 6 pairs of WADER container pockets in the loading area, for 1 x 20' container, 2 x 20' containers, or 1 x 40' container; an additional locking position is provided in the extension for a 45' container * 4 pairs of transverse stake pocket strips in the loading area for approx. 100 x 50 mm plug-in stakes * Storage for max. 9 pairs of plug-in stakes bolted inside to the front wall * Boarding ladder mounted left and right in the direction of travel * One INOX toolbox, approx. 1,200 x 460 x 550 mm, mounted front left under the loading platform * An additional INOX toolbox, approx. 1,200 x 46...

Condition: used, empty load weight: 6,920 kg, maximum load weight: 31,080 kg, overall weight: 38,000 kg, axle configuration: 3 axles, first registration: 09/2023, total length: 2,550 mm, total width: 4,000 mm, total height: 13,200 mm, suspension: air, tire size: 385/65 R22.5, Equipment: ABS, | Gsodam Plateau with stanchions | SAF axles | 1st axle liftable | Spare wheel holder | Toolbox | Tyres: 385/65 R22.5 | 6,970 kg tare weight, 31,080 kg payload | Stanchions | Austrian vehicle | Very good condition | Subject to error and prior sale. Tjdpfx Agow Hw Ufobsd

Condition: used, maximum load weight: 29,350 kg, overall weight: 36,000 kg, axle configuration: 3 axles, first registration: 05/2013, loading space length: 13,730 mm, loading space width: 2,495 mm, loading space height: 2,000 mm, total width: 2,550 mm, total height: 3,289 mm, Equipment: ABS, Platform body, raised bulkhead approx. 2000 mm, screen-printed floor, Multi-Lock outer frame, 10 stake pockets per side, 10 stake pockets in the center of the loading area, stake storage under the chassis, 2x storage boxes, JOST landing gear, mount for rotating beacon at the rear, ABS, EBS, MERCEDES-BENZ axle(s), disc brake system, air suspension with lifting/lowering device, lift axle, vehicle can be covered with advertising and/or lettering. Tedpfx Agev Ity Uebed Our offer generally does not include a new TÜV inspection. If a new TÜV inspection is desired, we would be happy to provide you with an offer from our partner workshops! The vehicle can be covered with advertising and/or lettering. Our general terms and conditions of delivery and payment apply. We would be happy to provide you with a financing or leasing offer for this vehicle. Please contact us!

Condition: new, overall weight: 36,000 kg, axle configuration: 3 axles, loading space length: 13,620 mm, loading space width: 2,480 mm, loading space height: 750 mm, Year of construction: 2024, Equipment: ABS, ( sample pictures ) SADDLE CONSTRUCTION KRONE TRIDEC 3-axle SDP 27/eLNZ4-BS / 750 mm BW /TRIDEC make/manufacturer : KRONE EZL : NEW VEHICLE dimensions : 13620 x 2480 x 750 gross vehicle weight : 36000 kg empty weight : 7019 kg air suspension lift/lower, disc brakes, spare wheel holder, ABS, EBS, axle make : BPW ECO PLUS ver. 3 lift axle, screen-printed floor, tie-down rings, toolbox, exterior paint finish : black KTL, body paint finish : white Tjdou S Tzbepfx Agbod chassis paint : black KTL, tires: 6-ply, tire condition : 100 %, tires HA 385 /55 R 22.5 4 pairs of 750 mm high drop sides CONSTRUCTION PANELS with 29 x stake pockets 81 x 81 in the center and in the outer frame + 12 steel stanchions on the left of the frame 12 pairs of reinforced lashing holes a 4 to 12 pairs of multi lash lashing rings multillock outer frame ( usable with closed bw ) steel bulkhead 1600 mm high reinforced version LIFTACHSE fully automatic 15 + 2 x 7 pole front socket toolbox / e wheel holder BPW ECO PLUS VERSION 3 !!!!! TRIDEC FORCED STEERING ( rod and 2 x turntable ) comes to every construction site wheelbase 1310 /2050 mm all information without warranty , subject to prior sale !!! if you have any questions for this or other vehicles please call us . if you have any questions for this or an other trailer / car please call us .

Condition: used, maximum load weight: 28,850 kg, overall weight: 36,000 kg, axle configuration: 3 axles, first registration: 05/2006, next inspection (TÜV): 10/2025, loading space length: 13,600 mm, total width: 2,500 mm, total height: 4,000 mm, Equipment: ABS, Krone semi-trailer - Platform - Drum brake - Disc brake - Tires: 385 / 55 R19.5 - TÜV due: 10/2025 Tsdpfxow Ehcko Agbsd - Safety inspection due: 04/2025 Errors and prior sale excepted. Internal vehicle number: 11201

Condition: new, overall weight: 42,000 kg, axle configuration: 3 axles, total width: 2,550 mm, Equipment: ABS, Delivery time: approximately 3-4 months after receipt of order! NEW VEHICLE Kässbohrer Platform Light SPS 3 # Unladen weight 6,100 kg # Fifth wheel load 15,000 kg # BPW axles with disc brakes # 1st axle as lift axle # Jost landing gear 24 t # Wabco 4S/2M EBS with RSS # 2 x 7 and 1 x 15-pin electrical connections # 24V Aspöck lighting system # Tires: 6 x 385/65 R 22.5 brand-name tires # 2 plastic wheel chocks Todpfeivw Dvsx Agbsd Equipment: # 30 mm hardwood floor # Over-width equipment (4 galvanized over-width panels with LEDs + 1 rotating beacon) # Stainless steel toolbox on the right in the direction of travel # 6 x 2 Jost container locks, retractable # Stanchion holder mounted on the front wall + 20 stanchions (1500 mm) # 4 rows of stake pockets # 10 x 2 stake pockets in the frame # 7 x 2 4t lashing rings on the platform # 108 lashing points on the outer frame, each with a capacity of 2t # Front wall with Code XL certification! # Chassis cathodic dip-coated and painted RAL 3020 Traffic Red # Front wall RAL 3020 Traffic Red ----Subject to errors, changes, and prior sale! Location: KTH-Trailer GmbH, 47574 Goch, Germany

Condition: new, maximum load weight: 61,050 kg, overall weight: 73,000 kg, axle configuration: > 3 axles, Equipment: ABS, You can find our complete vehicle inventory, including vehicles available immediately or at short notice, on our website. Excerpt from the equipment. Full equipment list available upon request. Loading Platform: * Loading platform with approx. 30 mm thick hardwood floor * 10 pairs of folding external lashing rings (LC 10,000 daN) Landing Legs: * JOST landing legs (mechanical) with two-speed gearbox for approx. 24 t lifting capacity (approx. 50 t test load) Axles and Suspension: * BPW axles, technically rated at 12,000 kg each * 1st axle steered, 2nd axle fixed, all other axles hydro-mechanically forced steered, mounted on turntable * Air suspension with raise/lower valve * Axle tools Tyres: * Tyres 445/65 R 22.5 169K – manufacturer of our choice TPMS * TPMS tyre pressure monitoring system according to ECE R 141 * Data transmission to tractor unit via standardised EBS interface according to ISO 11992 * For correct display, the tractor unit must be able to process and display this data Brake System: * Wabco brake system as per EU regulations with EBS-E (4S/3M) without connecting lines to the tractor unit Electrical System: * Electrical system in accordance with EU regulations * Lighting 24V ASPÖCK-NORDIK (ASS3) * All LED side marker lights flash with the indicator * ASPÖCK-UNIBOX at the front connection rail with 24N, 24S & 15-pin sockets according to ISO. 24N ISO-1185 24S ISO-3731 15-pin ISO-12098 Steel Structure: * Steel construction made of high-strength fine-grained steels * Steel grades: S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa) Paintwork: * Entire steel construction automatically blasted after welding using a shot-blasting machine * Second blasting with corundum for optimal coating adhesion * HRM metallisation of the entire vehicle chassis with ZINACOR 850 (85% zinc/15% aluminium) to ensure optimal corrosion protection * Final coating with 2 layers of 2K topcoat, single color in RAL 3002 Carmine Red as per RAL System 841GL Tjdpjw Tpr Usfx Agbed * Rear section metallised and painted in RAL 9010 (Pure White) * Rims in silver grey * Paint system tested by salt spray test according to ISO 9227-NSS * Cavities sealed with special wax * Metallic paint finish not possible Including the following accessories: * Loading platform with approx. 30 mm thick hardwood floor * 2-inch kingpin * One galvanized steel front wall (EN12642-XL), approx. 1,200 mm high * Yellow-red air couplings on the galvanized front connection rail * Storage for approx. 1,000 mm long insertable stanchions in the rear central beam * At the gooseneck and rear plate, left and right, one bracket each for warning signs including socket * Remote steering from front and rear via cable remote control with push-buttons, with single-track monitoring of the axles (no installation in the tractor unit) * Electro-hydraulic unit * 13 pairs of stanchion pockets for insertable stanchions approx. 100 x 50 mm in the outer frame of the loading platform * Lift axle on 1st and 2nd axle with control via TEBS E depending on current axle load and loading status * 7 pairs of galvanized insertable stanchions, approx. 100 x 50 mm, approx. 1,000 mm high * 5 pairs of crosswise stanchion pocket strips mounted on the loading platform for stanchions approx. 100 x 50 mm * 2 pairs of WADER container pockets in the loading platform, for 1x10' * 1 shunting coupling with reinforcement bolted to the rear crossmember * Central lubrication system BEKAMAX (Pico) with standard grease NLGI-2

Condition: new, overall weight: 36,000 kg, axle configuration: 3 axles, loading space length: 13,620 mm, loading space width: 2,540 mm, total width: 2,540 mm, Year of construction: 2025, Equipment: ABS, WEB TRAILER PRSH 27 PLATEAU with hardwood floor Dimensions: Chassis width approx. 2480 mm Chassis length approx. 13620 mm Wheelbase approx. 7700 mm Support winch position approx. 2300 from kingpin (only 2-axle tractors) Ride height .1280 mm at 1150 mm fifth wheel height Spring center approx. 1300 mm Fifth wheel load max. approx. 12000 kg Axle loads: 24 000 kg Approval: CoC papers Chassis: Chassis made of welded longitudinal members and through-bolted cross members Outer frame height approx. 125 mm, 4 mm with groove for lashing eyes 13 pairs of lashing eyes (bracket) screwed into the outer frame with groove, 5t each!! Landing gear: 24 ton telescopic landing gear, branded product (Jost/SAF) Axles Tjdpfx Aeg Dkx Esgbsd Branded product (SAF/BPW/JOST) 9 ton 22.5" disc brake, total stroke approx. 180 mm without axle lift (option) Axle spacing approx. 1310/1310 mm Brake: EBS braking system, Knorr or Wabco Air connections, coupling head red and yellow Lifting and lowering device with 1 rotary slide valve, Knorr/Wabco Air tank 2 x approx. 80 l Tire pressure control Lighting system: LED 15-pin connection at the front Flashing SML Tires: Branded tires 385/65 R 22.5 on steel wheels Construction: Steel bulkhead approx. 1200 mm high, with sheet metal cladding, bolted on Design Floor: Weatherproof hardwood floor 28 mm alternating with galvanized Omega steel profiles Hardwood boards screwed onto the crossbeams (optional double screwing) Floor: Certificate for tested forklift axle load 9.0t according to DIN EN 283 Attachments: Rear lamp plate premium, large and edged Underrun protection in welded design (rectangular tube) Access ladder rear right, foldable and extendable with platform Two wheel chocks with bracket, plastic or galvanized Plastic mudguards 180° above each axle Side collision protection on both sides aluminum or plastic profile Coating: Chassis painted in RAL 9005 or Nova gray 7350 Other colors at an additional cost (only if color is available in powder) KTL with zinc phosphating plus powder, highest corrosion protection Hot-dip galvanizing (optional) Price ex works Attention!!! Images show special equipment Let us advise you and work out a free and non-binding offer. Leasing, financing or hire purchase possible! We can accommodate your wishes! Ask us - we will be happy to make you an offer. Subject to errors and prior sale!!!

Condition: used, maximum load weight: 32,050 kg, overall weight: 38,000 kg, axle configuration: 3 axles, first registration: 03/2009, next inspection (TÜV): 02/2021, loading space length: 11,840 mm, loading space width: 2,500 mm, loading space height: 400 mm, Equipment: ABS, * Lift axle (high-mounted) * Air suspension * Disc brake * Curb weight: 5950kg * Bracken * ALU rims Tedpfxet Tuxfe Agbod ----Internal vehicle number: 9786-----Subject to errors and prior sale

Condition: new, overall weight: 42,000 kg, axle configuration: 3 axles, total width: 2,550 mm, total height: 1,180 mm, Equipment: ABS, Availability: Immediately NEW VEHICLE Kässbohrer Platform Light MEGA SPS 3 Tedpfxevm Nm Io Agbed # Empty weight 6,100 kg # Fifth wheel load 15,000 kg # Fifth wheel height: 980mm # BPW axles with disc brakes # 1st axle as lift axle # Jost support feet 24t # Wabco 4S/2M EBS with RSS # 2 x 7 and 1 x 15-pin electrical connections # 24V lighting system Aspöck # Tires 6 x 445/45 R19.5 branded tires on steel rims # 2 plastic wheel chocks Equipment: # 30 mm hardwood floor # Over-width device (4x over-width panels galvanized with LEDs + 1x rotating beacon) # 2 stainless steel tool boxes in the direction of travel right & left # 6x2 Jost container locks, retractable # Stake holder mounted on front wall + 20 stanchions (1500 mm) # 4 rows of stake pockets # 10 x 2 stake pockets in the frame # 7 x 2 lashing rings 4t on the platform 108 lashing points in the outer frame with 2t each # Side walls 600mm high & removable including depot under the vehicle # Chassis KTL coated and painted in RAL 3020 # Front wall RAL 3020 ----Errors, changes and prior sale reserved! Location: KTH-Trailer GmbH in Goch

Condition: new, maximum load weight: 36,245 kg, overall weight: 45,000 kg, axle configuration: 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory, including vehicles available for immediate and short-term delivery, on our website. Excerpt from the equipment list. The full list of features is available upon request. Loading Platform: * Hardwood loading platform with rear bevel approx. 1,000 mm x 8° * 2 pairs of lashing rings (LC 5,000 daN) * 1 pair of lashing rings (LC 10,000 daN) * 6 pairs of outward-folding lashing rings (LC 5,000 daN) * 2 pairs of outward-folding lashing rings (LC 10,000 daN) * Cut-outs in the outer frame of the loading platform for attaching tension straps (LC 2,000 daN) Landing Legs: * JOST landing legs (mechanical) with 2-speed gearbox for approx. 24 t lifting capacity (approx. 50 t test load) Axles: * BPW axles, air-suspended * Disc brakes (approx. 377 mm) * Lift/lower function (ET 120) * Axle tool kit Tyres: * 435/50 R 19.5 tyres – brand at our discretion * TPMS tyre pressure monitoring system according to ECE R 141. Data transfer to the tractor unit occurs via standardized EBS interface according to ISO 11992. For correct display, the tractor unit must be capable of transmitting and displaying this data. Braking System: * Wabco braking system according to EU regulations with EBS-E (2S2M) without connecting lines to the tractor unit Steel Structure: * Steel construction made of high-strength fine-grained steels * Steel grades: S355J2+N/S355MC (yield strength 355 MPa); S690QL/S700MC (yield strength 690 MPa) Electrical System: * Electrical system according to EU regulations * 24V ASPÖCK-NORDIK lighting (ASS3) * All LED side marker lights flash with the indicator * ASPÖCK-UNIBOX on the front connection bar with 24N, 24S, & 15-pin sockets according to ISO; 24N ISO-1185, 24S ISO-3731, 15-pin ISO-12098 Painting: * Complete steel structure blasted automatically with a shot blasting machine after welding * Second blasting with corundum for optimal coating adhesion * HRM-metallization of the entire chassis with ZINACOR 850 (85% zinc/15% aluminum) for maximum corrosion protection * Final painting with 2 coats of 2K finish paint, single color in RAL 3002 Carmine Red according to RAL system 841GL * Rear section metallized and painted in RAL 9010 (Pure White) * Paint system tested in salt spray test according to ISO 9227-NSS * Cavities sealed with special wax * Metallic paint not possible Including the following additional equipment: * Yellow-red air couplings on the galvanized front connection bar * 4 wheel chocks with holders * 2" kingpin * Loading platform with heavy-duty hardwood floor * 1 spare wheel holder under the loading platform, right-hand side in the direction of travel * Galvanized folding supports under the loading platform's beveled section * 9 pairs of stanchion sockets for plug-in stanchions, approx. 100 x 50 mm, in the outer frame of the platform * One galvanized steel front wall (EN12642-XL), approx. 1,600 mm high * Anti-slip painted sand layer on the central beam * 1 INOX toolbox transversely mounted under the platform, approx. 1,000 x 400 x 2,500 mm Tedpfx Agow Tpqqobed * 6 pairs of WADER container pockets in the floor for 1x 20' container, 2x 20' containers or 1x 40' container * 3 pairs of crosswise stanchion socket strips in the platform for plug-in stanchions approx. 100 x 50 mm * Storage for max. 9 pairs plug-in stanchions, approx. 100 x 50 mm, bolted to inner front wall * 2 INOX toolboxes under the platform left and right, approx. 600 x 350 x 600 mm * Holder for aluminium loading ramps, transverse under the pla

Condition: new, overall weight: 45,000 kg, axle configuration: 3 axles, total width: 2,550 mm, total height: 1,040 mm, Equipment: ABS, NEW VEHICLE Kässbohrer MEGA SPA M3 extendable platform Delivery time: approx. 4 months after order receipt # Fifth wheel load 18,000 kg # Fifth wheel height: 950 mm # 3,500 mm extendable Axles / Braking System: # BPW axles with 17.5" drum brakes # 3rd axle as self-steering axle # 1st axle as lift axle Tjdpfxjvm Nnls Agbjd # WABCO 4S/3M braking system # 12 x brand-name tires 245/70/17.5" on steel rims # 50 t support legs # 2 x 7-pin and 1 x 15-pin electrical connections # 24V Aspöck lighting system # 2 plastic wheel chocks Equipment: # Non-removable sliding table, 300 mm long # 30 mm hardwood floor # Over-width device (4 over-width boards) Galvanized with LEDs + 1 rotating beacon) # Plastic toolbox 600mm x 480mm x 450mm # Fire extinguisher box # 6x2 container locks, retractable # Stake holder mounted on the bulkhead + 18 100mm x 50mm stanchions # 4 rows of stake pockets perpendicular to the direction of travel # 10 x 2 stake pockets in the frame # 7 x 2 lashing rings 13.4t, 8 x 2 lashing rings 8t, 108 lashing points in the outer frame, each with a capacity of 2t # Bulkhead 1,500mm high with Code XL certificate! # Chassis cathodic dip-coated and painted RAL 3020 traffic red # Bulkhead RAL 3020 traffic red ----Subject to errors, changes, and prior sale! Location: KTH-Trailer GmbH in Goch

Condition: used, maximum load weight: 32,340 kg, overall weight: 39,000 kg, axle configuration: 3 axles, first registration: 07/2024, next inspection (TÜV): 07/2025, total width: 2,550 mm, Equipment: ABS, You can find our complete vehicle inventory, including immediately and short-term available vehicles, on our website. Excerpt from the equipment list. Full equipment details available upon request. Chassis * Welded construction made from high-grade steel profiles with punched-through crossmembers, designed for high point loads Coupling Device * 2-inch kingpin Underrun Protection * Bolted version, compliant with EU regulations Side Guard Protection * Compliant with EU regulations Landing Legs * 2 x 12 t landing legs with compensating foot and single-sided operation (right side in direction of travel) Axles * 3 x 9 t air suspension axle assembly * Disc brakes * Manufacturer: Gigant Brake System * Dual-circuit compressed air brake system compliant with EU regulations with EBS and RSS * Automatic load-dependent control * Spring-actuated cylinders for parking brake * Reversed polarity-safe coupling heads, permanently mounted on the front crossmember (no connecting line to tractor unit) * Manufacturer: Wabco Tyres Todpjwbb Ufsfx Agbod * 6 units, 385/65 R22.5 160J on steel rims 11.75 x 22.5 ET 120 Mudguards * Compliant with EU regulations * PVC mudguards in front of and behind the axle assembly Spare Wheel Carrier * 1 double basket incl. mounting material for one spare wheel with ET 120 Load Securing * 9 pairs of foldable lashing rings, evenly distributed, tensile force approx. 8.0 t * 8 pairs of foldable lashing rings, evenly distributed, tensile force approx. 2.5 t * External frame with drilled holes every approx. 500 mm for tension belts Front Wall * Reinforced steel construction, fixed * Inside lined with approx. 9 mm screen-printed flooring (approx. 1,250 mm high) Floor * Approx. 28 mm Z-hardwood floor recessed into the external frame Lighting System * Compliant with EU regulations, 24 Volt, with multi-chamber lights * LED side marker lights * LED position lights front (white) * LED outline lights at rear * Number plate lights * 1 x 15-pin and 2 x 7-pin plug connections on the front crossmember Paintwork * Chassis and front wall blast-cleaned, primed, and painted in a single color * Chassis: RAL 3002 carmine red * SSV: anodized aluminum * Underrun protection: white (RAL 9010) * Add-on parts: galvanized/KTL black * Rims: silver Additional Equipment * First axle liftable, with fully automatic, load-dependent lifting control * 10 pairs of stake pockets in the external frame, evenly distributed * 4 rows of stake pockets across the load floor * 20 pieces of stakes, galvanized tube 80/50, total length approx. 1,000 mm * Inside the front wall, a magazine for 20 plug-in stakes * 5 x 25 side and rear boards made of anodized aluminum hollow profiles, approx. 600 mm high, folding and removable * Removable Kinnegrip stakes * Sliding rails under the chassis left and right for side boards and stakes * Work light on lamp bracket (activated via reverse gear) * 2 PVC toolboxes, approx. 660 x 400 x 500 mm

Condition: new, overall weight: 42,000 kg, axle configuration: 3 axles, total width: 2,550 mm, total height: 1,180 mm, Equipment: ABS, Availability: Approx. 3-4 months after order receipt NEW VEHICLE Kässbohrer Platform Light MEGA SPS 3 Tedeivw D Ispfx Agbsd # Unladen weight 6,100 kg # Fifth wheel load 15,000 kg # Fifth wheel height: 980 mm # BPW axles with disc brakes # 1st axle as lift axle # Jost support legs 24 t # Wabco 4S/2M EBS with RSS # 2 x 7 and 1 x 15-pin electrical connections # 24V Aspöck lighting system # Tires: 6 x 445/45 R19.5 brand-name tires on steel rims # 2 plastic wheel chocks Equipment: # 30 mm hardwood floor # Over-width equipment (4 galvanized over-width panels with LEDs + 1 rotating beacon) # Stainless steel toolbox on the right in the direction of travel # 6x2 Jost container locks, retractable # Post holder mounted on the bulkhead + 20 posts (1500 mm) # 4 rows of post pockets # 10 x 2 post pockets in the frame # 7 x 2 4t lashing rings on the platform 108 lashing points in the outer frame, each with a capacity of 2t # Bulkhead with Code XL certification! # Chassis cathodic dip-coated and painted MB 7350 nova gray or RAL 3020 # Bulkhead MB 7350 nova gray or RAL 3020 ----Subject to errors, changes, and prior sale! Location: KTH-Trailer GmbH in Goch

Condition: new, maximum load weight: 56,570 kg, overall weight: 66,500 kg, axle configuration: > 3 axles, total width: 2,550 mm, Equipment: ABS, You can find our complete vehicle inventory, including immediately and short-term available vehicles, on our website. Tedjwx Dctepfx Agbod Extract from the equipment list. Complete specifications available upon request. Chassis: * Frame construction made of welded longitudinal beams and inserted cross beams * Underrun bar width approx. 700 mm * Fifth wheel plate at least approx. 8 mm thick, positioned between the longitudinal beams * Maximum crossmember spacing 400 mm (for longitudinally laid floor) * 3.5-inch king pin according to SAE standard, replaceable * Outer frame as UNP 200, open to the outside * Technical saddle load 26,500 kg Landing Gear: * 24 t telescopic landing gear JOST - MODUL CH (Heavy Duty) S-foot Axles: * 4 x 10 t SAF axles with large drum brakes * 22.5 single tires * Axle spacing approx. 1,700/1,810/1,810 mm * Air suspension system with 10 t load capacity each * Lifting and lowering device with 1 rotary slide valve Knorr/Wabco * Bracket for lifting and lowering device, bolted design Brakes: * Smartboard/TIM/Infocenter on bracket for lifting and lowering, in addition to the lift/lower valve * Without battery (operable only with towing vehicle) * Bracket for lights and brakes at the front of the underrun bar, total height approx. 700 mm * Basic version of tire pressure monitoring, connected to the EBS CAN bus system * With dual-release valve for brake and spring actuator * Test nipple for brake cylinder pressure at the front right brake cylinder * 1 coupling head each red and yellow * Lifting and lowering device mounted at the rear left (in the direction of travel) * EBS brake system by Wabco * EBS diagnostics via CAN bus (EBS plug), no external diagnostic cable provided! Tyres: * 8 x 445/65 R 22.5 - brand of our choice * Hub centering Lubrication: * Grease nipple strips on bogies and at the front of the steering system * No central lubrication Body: * Without body certificate according to DIN EN 12642 XL * 2x LED work lights on top of the front wall (facing rearwards), switch on lift/lower bracket * Heavy-duty front wall for platform * Side contour marking in yellow, rear in yellow * Front wall approx. 800 mm high, with sheet metal cladding, bolted design Lighting system: * 2x LED work lights mounted in the lamp plate, switched via reverse gear * 2x LED work lights, switched via reverse gear, 1 each side near landing gear * 2x LED reversing lights, 1 per side in front of 1st axle * Lighting/wiring system brand of our choice * License plate illumination * The towing vehicle must provide sufficient power for the selected lighting (esp. reverse light) * Front position lights, lower, white, 1 each right and left (LED) * 24 Volt lighting system with large multifunctional lamp * Side marker lights (LED) flashing * 1 x 15-pin and 2 x 7-pin connections at the front via multifunction box * EBS socket * 1 pair of lane departure lights (LED) Floor: * Hardwood floor approx. 28 mm, alternately with galvanized omega steel profiles Paint/Coating (no metallic colors): * Chassis painted in RAL 3002 flame red * Front wall (steel construction) painted in RAL 3002 flame red * Axle hubs in chassis color * Axles and landing gear in black * Wheels in aluminum/silver, similar to RAL 9006 * Wheel nuts untreated * Underrun protection painted in RAL 9010 pure white (aluminum) Accessories: * Lifting device for 1st axle * 9 hook plates welded into the outer frame per side. Lashing load max. 3,000 daN * 12 per side

Condition: new, overall weight: 48,000 kg, axle configuration: 3 axles, total width: 2,550 mm, total height: 1,040 mm, Equipment: ABS, NEW VEHICLE Kässbohrer platform extendable MEGA SPA MR3 with wheel recesses Color nova gray Availability: approx. 6 months after receipt of order # Fifth wheel load 18,000 kg # Fifth wheel height: 950mm # 6,900mm extendable Axles / brake system: # BPW axles with drum brake 17.5" # 3rd as self-steering axle # 1st axle as lift axle # WABCO brake system 4S/3M # 13 x Continental HTR 2 245 / 70 / 17.5" on steel rims # Jost support feet 24t # 2 x 7 and 1 x 15-pin electrical connections # 24V lighting system Aspöck # 2 plastic wheel chocks Equipment: # Wheel recesses with hardwood cover # Non-removable Sliding table 300mm long # 1 x 2 aluminum landing ramps 2,400mm long, 600mm wide, capacity 32,000 kg included # 30 mm hardwood floor # Over-width device (4x over-width board galvanized with LEDs + 1x rotating beacon) Tedegimw Uopfx Agbod # Toolbox on the right in the direction of travel # 6x2 holes for container locks for the transport of 1x20", 1x40" or 1x45" containers # 4 container locks twistlocks, removable # Stake holder mounted on the front wall without stanchions # 4 rows of stanchion pockets # 10 x 2 stanchion pockets in the frame # 8 x 2 lashing rings 10t, 5 x 2 lashing rings 8t, 108 lashing points in the outer frame with 2t each, # Storage box for aluminum ramps under the chassis behind the third axle # Front wall 1,500mm+500mm high with Code XL certificate! # Chassis KTL coated and painted MB7350 nova gray # Front wall MB7350 nova gray ----Subject to errors, changes and prior sale! Location: KTH-Trailer GmbH in Goch

Condition: new, maximum load weight: 34,350 kg, overall weight: 42,000 kg, axle configuration: 3 axles, total width: 2,550 mm, Equipment: ABS, You can find our entire vehicle inventory with immediately and short-term available vehicles on our website. Excerpt from the equipment. Full equipment details available on request. Chassis: * Welded construction made of high-quality steel profiles with through cross members, designed for high floor or point loads, equipped with a heavy-duty outer frame * Loading platform at the rear as a welded steel construction, with two welded-in outer driving rails made of 5-hole steel plate (Lohr/Rolfo hole pattern system) approx. 2,250 mm in length, hydraulically lowerable by approx. 350 mm * Rear section includes a hydraulically extendable loading table (approx. 1,500 mm), constructed from welded steel with 5-hole steel plate (Lohr/Rolfo hole pattern system) cover, lighting brackets, and two ramp compartments and ramp supports * Drive and control of the rear operated via electric-hydraulic power unit housed in a stainless-steel box mounted on the left of the chassis, with radio remote control * Power supplied by the towing vehicle’s battery (NATO socket on the front wall, without connecting cable to the truck) Towing Device: * 2" king pin, replaceable from below Underrun Protection: * Fixed as per EU standard Landing Legs: * 2 x 12 t support winches with 2-speed gearbox Axles: * 3 x 9 t air suspension axle assemblies * Brand: SAF, disc brakes approx. 370 x 45 mm * ABS * 10-hole hub-centric wheels, offset ET120 * Total air suspension travel approx. 310 mm (lifting approx. 220 mm, lowering approx. 90 mm) * Air suspension controlled via hand lever with stop function Lift Axle: * 1st and 3rd axles automatically liftable, can also be actuated from the chassis frame or via PIN 12 of the lighting socket Tires: * 6 units, 445/45R19.5, fitted on 14.00X19.5 rims, 10-hole ET120 Mudguards: * As per EU regulations, 1/4 PVC mudguards * 1st axle front and rear, 2nd and 3rd axle rear Brake System: * Brand: Wabco * Dual-line brake system as per EU with EBS, automatically load-dependent control * Spring-operated parking brake acting on 2 axles * Interchange-proof coupling heads fixed to the front cross member, no connection to towing vehicle Lighting System: * As per EU regulations, 24V, * Multi-chamber rear lights, * License plate lights * LED side marker lights * LED front position light (white) and rear track lights * 15-pin socket and 2x7-pin sockets fixed at the front cross member, no cables to towing vehicle Load Securing: * 9 pairs of foldable lashing rings evenly distributed, approx. 8 t pulling force * 8 pairs of foldable lashing rings evenly distributed, approx. 2.5 t pulling force Tedpfxowt Iylj Agbsd * 2 pairs of foldable lashing rings at the rear, approx. 2.5 t pulling force * External frame with holes approx. every 500 mm for tie-down straps Stake Pockets: * 16 plug-in stakes approx. 100/40 mm, usable length approx. 800 mm Stake Pockets: * 8 per side integrated into the outer frame * 4 rows of stake pockets transverse to the loading area Floor: * Approx. 28 mm Z-grade hardwood floor recessed into the outer frame Front Wall: * Solid front wall * Depot for 16 plug-in stakes approx. 100/40 * Front wall bolted to the top frame Equipment: * 2 wheel chocks with holders * 2x PVC toolboxes, approx. 600/400/500 mm * Holder for beacon light at rear incl. lamp * 2 LED reversing lights (rear) * 2 aluminum loading ramps, dimensions approx. 1,550 x 400 mm, load capacity approx. 4,000 kg/pair * Wheel load

Condition: new, maximum load weight: 39,850 kg, overall weight: 45,000 kg, axle configuration: 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory, including immediately and short-term available vehicles, on our website. Excerpt from the specifications. Full equipment details available upon request. Chassis: - Welded construction from high-quality steel sections with through-profile cross members - Designed for high point loads. Outer frame as UNP profile - Fifth wheel plate approx. 8 mm, underride guard nose approx. 700 mm wide - Bracket at front for customer-side mounting of a support device, approx. 90 x 90 x 4 mm Coupling device: - 2-inch kingpin (mount also suitable for 3.5) Rear underrun protection: - According to EC, bolted design Side underrun protection: - According to EC Tsdpfx Agewx Dbpobed Landing gear: - 24 t landing legs with single-side operation (test load approx. 66 t), Jost Modul CH (Heavy Duty) S-foot Axles: - 3 x 9 t air suspension axle units, manufacturer of our choice, with disc brake approx. 430 x 45 mm - ABS - Hub-centric wheel mounting, 10-hole, ET 120 - Total air suspension travel approx. 200 mm, of which raising approx. 140 mm and lowering approx. 60 mm, controlled via rotary slide valve with detent, with RTR function - Switch for second ride height (+ approx. 50 mm) on the bracket of the lifting and lowering device - Smartboard/TIM/Infocenter, without TPMS display Lifting axle: - First axle liftable, with fully automatic load-dependent lift control, starting aid via button in the driver’s cab (15-pin socket PIN12). Button in cab not included in delivery Braking system: Manufacturer of our choice - Two-line compressed-air braking system according to EC with EBS and RSS, automatic load-dependent adjustment - Spring brake cylinder as parking brake - Mistake-proof coupling heads mounted securely on front cross member, without connecting line to the motor vehicle Tyres: - 6 units, 385/65 R22.5 160J on 11.75 x 22.5 rims (manufacturer of our choice), ET 120 - Basic version tyre pressure monitoring, connected to EBS CAN-bus system - Tyre pressure display in driver’s cab (pre-installed by truck manufacturer) Mudguards: - According to EC, PVC mudguards (half-shells) over all axles - Anti-spray mudflaps Load securing: - 8 pairs of lashing plates welded into the outer frame (pulling force approx. 3 t) - 6 pairs of lashing rings on the side of the outer frame, evenly distributed (pulling force approx. 10 t) - 13 pairs of lashing eyes (bails) on the outer frame (tested lashing capacity approx. 2.5 t per point) Stake pockets/stakes: - 5 pairs of stake pockets recessed in the outer frame, approx. 90 x 90 x 4 mm - 3 pairs of stake pockets recessed in the loading floor, approx. 90 x 90 x 4 mm - 10 plug-in stakes made of galvanized box section, approx. 80 x 80 x 4 mm, with stop at the bottom Front wall: - Bolted front wall, approx. 1,200 mm high, covered with approx. 5.5 m sheet metal Stake magazine: - Inside the front wall, a magazine for plug-in stakes Floor: - Approx. 28 mm hardwood floor recessed in the outer frame, with galvanized omega steel profiles Lighting system: - According to EC, 24 volts with multi-chamber taillights - LED side marker lights - LED front position lights white - LED rear outline marker lights - Number plate lights - 1x 15-pin and 2x 7-pin socket connectors on the front cross member Equipment: - Chock with double holder - Warning sign according to ECE 70 - 2 LED work lights on the lamp bracket (switched by reverse gear) - Bracket for optional rotating beacon at rear (incl. beacon) - 1 foldable and extend

Condition: used, maximum load weight: 32,610 kg, overall weight: 39,000 kg, axle configuration: 3 axles, first registration: 10/2023, next inspection (TÜV): 11/2025, total width: 2,550 mm, Equipment: ABS, You can find our complete selection of vehicles with immediately and short-term available units on our website. Sample from the equipment list. Full equipment details available upon request. Chassis: * Welded construction made from high-quality steel profiles with through-profile cross members, designed for high point loads. Coupling Device: * 2-inch king pin Underrun Protection: * Bolted version, compliant with EC regulations Side Impact Protection: * EC compliant Landing Legs: * 2 x 12 t landing legs with compensating foot and one-sided operation on the right hand side (FR) Axles: * 3 x 9 t air suspension axle assemblies * Disc brakes * Brand: Gigant Brake System: Todpfx Ajwyhy Eogbod * Dual-line compressed air brake system compliant with EC regulations, equipped with EBS and RSS, automatic load-dependent control * Spring brake cylinders as parking brake * Foolproof coupling heads permanently mounted on front crossmember, without connection line to tractor unit * Brand: Wabco Tyres: * 6 off, 385/55 R22.5 160J on steel rim 11.75 x 22.5 ET 120 Mudguards: * EC compliant, PVC mudguards in front of and behind the axle assembly Spare Wheel Carrier: * 1 piece double basket with mounting hardware for one spare wheel with ET 120 Load Securing: * 9 pairs of foldable lashing rings, evenly distributed, tensile force approx. 8.0 t * 8 pairs of foldable lashing rings, evenly distributed, tensile force approx. 2.5 t * Drill holes for tie-down straps approximately every 500 mm on the outer frame Front Wall: * Reinforced steel construction, fixed * Interior lined with approx. 9 mm phenolic plywood floor (approx. 1,250 mm high) Floor: * Approx. 28 mm Z-hardwood floor set in outer frame Lighting System: * EC compliant, 24 Volt, with multi-chamber lamps * LED side marker lights * LED front position lights (white) * LED rear outline marker lights * Number plate lights * 1x 15-pin and 2x 7-pin plug connectors on front crossmember Paintwork: * Chassis and front wall sand-blasted, primed and painted in single color * Chassis: RAL 3002 carmine red * SSV: aluminium anodized * Underrun protection: white RAL 9010 * Attachments: galvanized/KTL black * Wheels: silver Including Special Accessories: * First axle liftable with fully automatic, load-dependent lift control * 10 pairs of stake pockets in outer frame, evenly distributed * 4 rows of stake pockets crosswise to loading area * 20 stakes made of galvanized pipe 80/50, total length approx. 1,000 mm * Storage magazine for 20 plug-in stakes on inner front wall * Twistlocks for 1 x 40’ and 2 x 20’ containers, flush-mounted at the rear * Twistlocks for 1 x 20’ container in middle position * Work light on lamp bracket (switched via reverse gear) * 2 PVC toolboxes, approx. 660 x 400 x 500 mm

Condition: new, maximum load weight: 36,500 kg, overall weight: 48,000 kg, axle configuration: 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete inventory of immediately and short-term available vehicles on our website. Excerpt from the equipment features. Full equipment list available upon request. - Gooseneck, approx. 4,100 mm in length with central beam - Load platform with double-extendable design, length approx. 9,400 mm - BPW axles and suspension - All axles hydromechanically forced-steered - Technical axle load: 12,000 kg - Air suspension with raise and lower valve - Twin tires 235/75 R 17.5 3PMSF - WABCO braking system, EBS-E - 3 kW electro-hydraulic unit for hydraulic operations. Without installation of supply connections on the tractor unit - 4 pairs of stake pockets integrated in the outer frame of the gooseneck, suitable for insertable stakes approx. 100 x 50 mm - 2-inch king pin - 8 pairs of stake pockets integrated in the outer frame of the loading area, suitable for insertable stakes approx. 100 x 50 mm Tedpfxowvzg Rs Agbed - 1 lockable INOX toolbox, approx. 1,250 x 500 x 550 mm (L x W x H), mounted under the loading platform on the left-hand side in direction of travel - Remote steering control from front and rear using cable remote with push buttons, with axle tracking control, without installation in the tractor unit - 2 axle load gauges mounted on the left side - Steel front wall, approx. 1,600 mm high - 3 transverse rows of stake pockets mounted in the floor of the loading area for insertable stakes approx. 100 x 50 mm - 1 transverse row of stake pockets mounted in the floor of the gooseneck for insertable stakes approx. 100 x 50 mm - 1 additional lockable INOX toolbox, mounted under the loading area - WADER container pockets in the loading area for transporting: 2x 20' containers or 1x 40' container - Central automatic lubrication system with 2 pumps, BEKAMAX brand - Complete HRM Metalization (High Resistance Metallisation)

Condition: new, maximum load weight: 63,960 kg, overall weight: 76,500 kg, axle configuration: > 3 axles, total width: 2,550 mm, Equipment: ABS, You can find our complete vehicle inventory with immediately and short-term available vehicles on our website. The following is an extract from the specification. Complete specification available on request. Chassis: - Welded construction made of high-quality steel profiles with through-go crossmembers, designed for high point loads - Outer frame made of UNP steel Coupling equipment / fifth-wheel load: - 2-inch kingpin - Technically permissible fifth-wheel load: 26,500 kg Underrun protection: - According to EU regulations, bolted design Side impact protection: - According to EU regulations Landing legs: - Landing legs with single-side operation, support load approx. 66 t / lifting capacity approx. 24 t Axles: - 5 x 10 t air suspension axle units, make: SAF, with drum brakes approx. 400 x 200 mm - ABS - Wheel attachment, center-bored, 10-hole, offset ET 0 - Total air suspension stroke: approx. 200 mm, lift approx. 140 mm, lowering approx. 60 mm; control via rotary valve with detent function Steering: - 1 axle with leading steering, 2nd axle rigid, 3rd, 4th, and 5th axle with mechanical forced steering (Tridec) - Greasing points are routed centrally to the outside Axle lift: Todpfxswx Dcas Agbed - First and second axle automatically liftable, with additional cut-off at the chassis Brake system: - Two-line pneumatic brake system according to EU regulations with EBS and RSS, automatic load-dependent control, make: Wabco 4S/3M - Spring-actuated cylinders as parking brake - Interlocked coupling heads mounted securely on the front crossmember, no connecting line to the towing vehicle - Aluminum air tank Tyres: - 10 x 445/65 R22.5 164J on rim 11.75 x 22.5 ET 0 – brand of our choice TPMS: - Tire pressure monitoring system - TPMS according to ECE R141, with data transmission to towing vehicle Fenders: - According to EU regulations: 1st axle front, 2nd axle rear, 3rd, 4th, and 5th axle each front and rear with 1/4 PVC fender - Rear fender with mud flaps Load securing: - 5 pairs of folding lashing rings, evenly distributed (pulling force approx. 14 t) - 11 pairs of hook plates welded into the outer frame (pulling force approx. 3 t) - 10 pairs of lashing rings in the side outer frame, evenly distributed (pulling force approx. 8 t) Stake pockets: - 10 pairs of stake pockets set into the outer frame - 6 pairs of stake pockets set into the floor (at the outer longitudinal beam) Removable stakes: - 16 pieces galvanized plug-in stakes, approx. 80 x 80 x 8 mm, usable length approx. 850 mm Stake magazine: - One magazine per side in front of the front wall, each for 8 plug-in stakes approx. 80/80 mm Front wall: - Bolted corner stakes filled with aluminum hollow profiles, inside with a steel collision plate across the entire width and height Floor: - Approx. 28 mm Z hardwood flooring, let into the outer frame, flush-mounted Lighting system: - According to EU regulations, 24 V with multi-chamber lamps - LED side marker lamps - LED position lamps white front - LED outline marker lamps rear - License plate lamps - 1x15 and 2x7-pin plug connections on the front crossmember Equipment: - Wheel chocks with double holder - Warning sign in accordance with ECE 70 - Work spotlight on lamp mounting (activated via reverse gear) - Holder for rotating beacon at the rear (incl. rotating beacon) - 1 piece climbing ladder mounted rigidly on each side left and right, incl. removable climbing aid - Smart Board - Sticker indicating vehicle swing-out - Sticker indicating load cen

Condition: new, maximum load weight: 32,340 kg, overall weight: 39,000 kg, axle configuration: 3 axles, total width: 2,550 mm, Equipment: ABS, You can find our entire inventory of vehicles, including those available immediately or at short notice, on our website. Extract from the equipment list. Full equipment details available on request. Chassis: * Welded construction using high-quality steel profiles with punched-through cross-members, designed for high point loads Coupling device: * 2-inch kingpin Landing gear: * 2 x 12 t landing legs with compensating foot and single-side operation on the right front side Axles: * 3 x 9 t air suspension axle units * Disc brakes * SAF brand, with disc brake approx. 430 x 45 mm * ABS * Centrally positioned wheel mounting, 10-hole with ET 120 * Total pneumatic suspension lift approx. 200 mm, of which approx. 140 mm raising and 60 mm lowering, controlled via rotary lever valve with detent Brake system: * Dual-circuit air pressure braking system according to EC standards with EBS and RSS, automatic load-dependent control * Spring actuators as parking brake * Mistake-proofed coupling heads permanently mounted to the front cross member, with no connecting line to the towing vehicle Tyres: * 6 units, 385/55 R22.5 160J on steel rim 11.75 x 22.5 ET 120, brand of our choice Mudguards: * According to EC, PVC mudguards in front of and behind the axle unit Spare wheel holder: * 1 double basket incl. mounting kit for one spare wheel with ET 120 Load securing: * 9 pairs of folding lashing rings, evenly distributed, pulling force approx. 8.0 t * 8 pairs of folding lashing rings, evenly distributed, pulling force approx. 2.5 t * Outer frame with holes for tension straps approx. every 500 mm Front wall: Tjdpfx Ajwx Db Ajgbed * Reinforced steel construction, fixed * Interior lining approx. 9 mm birch plywood (approx. 1,250 mm high) Floor: * Approx. 28 mm Z-hardwood floor recessed into outer frame Lighting system: * EC compliant, 24 volts with multi-chamber lights * LED side marker lights * LED position lights white at front * LED outline lights at rear * Number plate lights * 1x 15-pin and 2x 7-pin connectors on the front cross member Equipment: * ECE 70 warning board * Bracket for rotating beacon (without beacon) Paintwork: * Chassis and front wall sandblasted, primed and painted in single color * Chassis: RAL 3002 (carmine red) * Sideboards: Anodized * Sideboard stanchions: RAL 3002 (carmine red) * SSV: Aluminum anodized * Hubs: KTL coated * Rear underrun guard: white (RAL 9010) * Attachments: galvanized/KTL black * Rims: silver Accessories: * First axle liftable, with fully automatic load-dependent lift control * 10 pairs of stanchion pockets in outer frame, evenly distributed * 4 rows of stanchion pockets across the loading deck * 20 stanchions made of galvanized tube 80/50, total length approx. 1,000 mm * Magazine for 20 plug-in stanchions mounted inside front wall * Sideboards: 5 x 25er sideboards and rear wall made of anodized aluminum hollow profiles, foldable and removable, removable Kinnegrip stanchions * Sideboard and stanchion magazine: insertion rails for sideboards and stanchions left and right under the chassis * Container locks for 1 x 40' and 2 x 20' containers at rear flush, container locks for 1 x 20' container in center position * Work light on lamp bracket * 2 stainless steel toolboxes, approx. 600 x 500 x 500 mm * Air suspension Safety: ABS * EBS * Disc brakes Extras: Rental possible

Condition: new, maximum load weight: 34,660 kg, overall weight: 48,000 kg, axle configuration: 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete stock of vehicles, including those available immediately or at short notice, on our website. Excerpt from the equipment. Full equipment details available upon request. Loading Platform * Double extendable version with pneumatically operated locking mechanism * 2 pairs of recessed lashing rings (LC 5,000 daN) * 1 pair of recessed lashing rings (LC 10,000 daN) Todpfx Agek Ugacobjd * 7 pairs of outward-folding lashing rings (LC 5,000 daN) * 3 pairs of outward-folding lashing rings (LC 10,000 daN) * Cut-outs in the outer frame of the loading platform for hooking in tension belts (LC 2,000 daN) Landing Legs * JOST landing legs (mechanical) with 2-speed gearbox, approx. 24 t lifting capacity (approx. 50 t test load) Tyres * 235/75 R 17.5 3PMSF Axles * BPW axles hydro-mechanically forced steered * Air suspension with lift and lower valve Braking System * According to EU regulations, with EBS-E (2S2M), without connection lines to the tractor unit Steel Construction * Made of high-strength fine-grain steels. Steel grades: S355J2+N/S355MC (yield strength 355 MPa), S690QL/S700MC (yield strength 690 MPa) Paintwork * Premium and durable corrosion protection for the standard shot-blasted welded frame provided by a 2-component (2K) zinc-rich primer * High-quality 2-component (2K) top coat, single color in RAL 3002 carmine red * Rear section metallized and painted in RAL 9010 (pure white) * Rims in silver Including Accessories * Remote steering from front and rear via cable remote control with push buttons, with single-track control (no installation in tractor unit) * Electro-hydraulic power unit * 4 wheel chocks with holder mounted on the front wall * 2-inch kingpin * Yellow-red air couplings on the galvanized connection strip at the front * Yellow reflective tape according to EU regulations on the sides, extension, and rear of the trailer * European reflective signs (red-yellow) on the trailer's rear * One mudflap on the trailer's rear * Manual and instructions on USB stick * Loading platform with robust hardwood floor * 10 pairs of stake pockets for 100 x 50 mm plug-in stakes on the outer frame of the loading platform * Mounting bracket for a revolving beacon on the trailer's rear * Galvanized supports under the inclined section of the loading platform * Mounting bracket for a revolving beacon on the trailer's rear * Hook-in rail for ALU access ramps at the rear of the vehicle * 80 km/h speed stickers on the rear and both sides * Load gauge for determining axle loads including load chart * One galvanized steel front wall (EN12642-XL), approx. 1,600 mm high * Central lubrication system with 2 BEKAMAX (Pico) pumps with standard grease NLGI-2 and removable pump protection cover * Spiral cable supplying the electro-hydraulic unit and/or the electric winch (approx. 35 mm², approx. 3.5 m long, max. 250 A) between trailer and tractor unit with connector (NATO-NATO) * Coated sand layer on the central beam as anti-slip protection * 6 pairs of WADER container pockets in the loading platform, for 1 x 20' container, 2 x 20' containers or 1 x 40' container, an additional locking point is provided in the extension for a 45' container * 5 pairs of crosswise stake pocket rails mounted in the loading platform, for 100 x 50 mm plug-in stakes * Storage for up to 9 pairs of plug-in stakes, approx. 100x50 mm, inside on the front wall * One INOX toolbox, approx. 1,500 x 390 x 810 mm, mounted under the loading platform left and right in the direction of trav

Condition: used, maximum load weight: 36,400 kg, overall weight: 48,000 kg, axle configuration: 3 axles, first registration: 04/2024, next inspection (TÜV): 06/2026, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory, including vehicles available for immediate or short-term delivery, on our website. Excerpt from the equipment. Complete equipment list available upon request. Loading Platform: * Gooseneck, approx. 4,100 mm long, with central beam * Loading platform in double-extendable design, approx. 9,400 mm long, with pneumatically operated locking mechanism * A fixed intermediate table, approx. 200 mm wide, is welded to the central beam * Supply lines are routed protected inside the extendable beams and automatically adapt to the respective loading platform length (exception: supply to the first locking mechanism) * For tractor units: 4 x 2 and 6 x 2 Axles and Suspension: * BPW axles and suspension, all axles hydro-mechanically force-steered, mounted on turntables * Technical air suspension with lift and lower valve Tyres: * 235/75 R 17.5 3PMSF twin tyres * Brand of our choice. Load index 143/141J (144/144F) Braking System: * WABCO EBS-E braking system according to EU regulations Metallisation: * Complete HRM metallisation (High Resistance Metallisation) Tjdpjw E A Egsfx Agbsd * Entire steel structure shot-blasted, then hot-finished with ZINACOR 850 (Zinc 85% - Aluminium 15%) Painting: * 6-coat final treatment: Entire steel structure shot-blasted after welding. One coat of zinc-based primer, one coat of adhesion primer. Final topcoat: 2 coats of 2-component acrylic paint, single colour, followed by cavity sealing with special wax * Trailer colour: RAL 3002 Carmine Red * Wheel rim colour: Silver grey * Lamp bracket colour: RAL 9010 Pure White Included Accessories: * Steel front wall, approx. 1,600 mm high, certified version according to EN12642:2016 XL. Max. load capacity: 20,000 daN * 4 pairs of recessed lashing rings in the gooseneck outer frame: the front 3 pairs fitted horizontally (LC 10,000 daN), rear pair fold-out to the outside (LC 10,000 daN) * 4 pairs of stake pockets set into the gooseneck outer frame for plug-in stakes approx. 100 x 50 mm * 1 transverse stake pocket rail mounted at the rear in the gooseneck floor for plug-in stakes approx. 100 x 50 mm * 2-inch kingpin * 4 wheel chocks with holders in front of the front wall * Mechanical landing gears with 2-speed gearbox and crank. JOST Modul B, static test bearing capacity approx. 50,000 kg * On gooseneck and loading platform, wooden flooring approx. 32 mm thick, framed in aluminium omega profiles * Large cross-section extension tube with a locking point every approx. 500 mm * Small cross-section extension tube with a locking point every approx. 1,000 mm, providing a locking interval of approx. 500 mm * 10 pairs of recessed horizontal lashing rings in the outer frame of the loading platform, fold-out to the outside: one pair before the last axle and one pair at the end crossmember of the trailer (LC 10,000 daN each), all other lashing rings (LC 5,000 daN) * 8 pairs of stake pockets set into the outer frame of the loading platform for plug-in stakes approx. 100 x 50 mm * 3 transverse stake pocket rails mounted in the loading platform floor for plug-in stakes approx. 100 x 50 mm * 1 spare wheel carrier under the loading area on the right-hand side (direction of travel) * 1 lockable stainless steel toolbox, approx. 1,250 x 500 x 550 mm (L x W x H), mounted under the loading area on the left (direction of travel) * Access ladder mounted on the right (direction of travel) * Last axle with air bellows venting activated by operating the parking brake * 3 kW electr

Condition: new, maximum load weight: 32,480 kg, overall weight: 39,000 kg, axle configuration: 3 axles, total width: 2,550 mm, Equipment: ABS, You can find our complete vehicle inventory, including vehicles available for immediate and short-term delivery, on our website. Excerpt from the equipment list. Full equipment specification available on request. Chassis * Standard ladder-type frame in lightweight steel construction with inserted cross members * Coupling plate approx. 8 mm thick, with a dual kingpin according to DIN 74080 / ISO 337 Running Gear * Axle lift mechanism on the axle * Fully automatic, load-dependent axle lift control * Start assist: Activation via 3x braking, 30% overload up to a speed of 25 km/h * BPW three-axle assembly ECO Air, with disc brakes approx. Ø 430 mm, offset approx. 120 mm * Air suspension with approx. 180 mm stroke Tsdpfjw E A Emox Agbjd Vehicle Tyres * Wheels fitted with internal sensors in accordance with UN ECE R141 * Six 385/65 R 22.5 UNIROYAL TH 50 tyres * Six steel rims 22.5 x 11.75, offset approx. 120 mm (ET 120) Chassis Attachments * Landing gear (make at Kögel’s discretion) mechanical with compensating foot, approx. 24 t lifting capacity, single-sided operation on the right in direction of travel * Spray suppression system in accordance with Regulation (EU) No. 109/2011 on three-axle assembly with 385/65 R22.5 tyres consisting of: 1 pair of quarter-circle mudguards in front of the axles, 1 pair of straight mudguards with mudflaps between 1st and 2nd axle, and 1 pair of quarter-circle mudguards with mudflaps behind the axles * Sideguard protection according to ECE-R73 * 2 plastic toolbox containers, waterproof, internal dimensions approx. 545 x 400 x 400 mm * Rear right extendable access ladder * High, rigid rear under-run protection in steel according to ECE-R58 * 1 pair each of extendable warning signs for overwidth loads, retro-reflective red/white, with LED lighting, coiled cable and plug connector. Fitted at the front and rear of the vehicle Brake / Air Suspension System * Wabco EBS system 2S/2M with stability program (includes ABS/ALB function), EBS connection ISO 7638 (without connecting lines), parking brake as spring-loaded brake, external pneumatic connections and external EBS diagnostic connector via ISO 7638 plug * Air suspension system incl. 1 lift and lower valve, mounted left in the direction of travel behind the axle assembly. Driving position adjusts automatically * 2 anti-swapping coupling heads at the front ISO 1728 * Steel air reservoirs for brake system and air supply (EN 286-2) Floor * Board floor approx. 30 mm thick, circumferentially sealed * Socket pockets for square insert posts approx. 80 x 80 mm, arrangement according to drawing J9: 8 socket pocket strips (18 pockets per strip: 4 outside + 10 centrally positioned) Front Wall * Storage for up to 14 square insert posts approx. 80 x 80 mm (length approx. 1,990 mm) on the inside of the front wall * Front wall approx. 2,000 mm high with volumetric corner stanchions in steel, profiled steel sheeting, bolted/riveted to frame * 2 pairs of lashing points (permissible lashing capacity approx. 1,000 kg per ring) on the front wall according to EN 12640 Side Wall * VarioFix steel perforated external frame * 24 pairs of lashing rings in the external frame (to EN 12640), permissible pulling force approx. 5,000 kg per ring Impact Protection * 1 pair of steel impact buffers approx. 160 x 85 x 85 mm mounted externally on the frame end plate * Crosswise zinc-plated steel angle as forklift protection, as well as central lock cam protection, mounted on the frame end plate Electrical / Elect