Used Fliegl Trailers for sale (305)

Condition: new, machine/vehicle number: b50cac2c60a813b0968994fa0, empty load weight: 5,700 kg, maximum load weight: 18,300 kg, overall weight: 24,000 kg, axle configuration: 2 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction Turntable with powerful ball bearing slewing ring Folding rear support 2 wheel chocks with holder Rear spray flaps across the entire width Preparation for widening to 3,000 mm (holes in the outer frame and not in the rear slope) Low loader lashing eyes 1 pair of lashing cut-outs in the front side member on offset, 10 tons each 7 pairs of lashing points at the top and sides of the outer frame, 10 tons each 1 x front on offset 5 x in the drop deck 1 x in the rear slope 12 pairs of lashing holes in the outer frame, each with 5 to. (lashing strap attachment) 5 x crank, 6 x low bed and 1 x in rear slope Trailer drawbar Turntable Drawbar with tested 40 mm drawbar eye Axles + suspension Drum brake axles, at the manufacturer's choice Axle/chassis laser-measured Reduction in tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation (rocker compensation) Wheels and tires 235 / 75 R 17.5 Fulda Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 non-interchangeable clutch heads at the front, with connecting lines to the motor vehicle, Cgedpfxji Ri Ago Afdon Connecting lines extended by approx. 60 cm without ABS, but with mechanical ALB, then max. 60 km/h approval Electrical system 12 volt, multi-chamber lights, without amber LED lighting at the sides, reflectors at the sides 2 white position lights at the front 2 white/red lane departure lights at the rear 1 x 7-pin 12 volt plug at the front, with connecting cable, extended by approx. 60 cm 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, illuminated and extendable to 3,000 mm, floor Front offset with steel/ checker plate covering Storage box recessed in drive-over slope to the offset Then with 70 mm softwood floor, steel/ checker plate covering in the wheel arch area Rear slope with 70 mm softwood floor Deep loading area incl. rear slope 5900 mm Drive-on ramps Steel ramps 2 800 mm long, 750 mm wide, can be moved sideways covered with wood with spring lift support Operating instructions With an axle load of 10,000 kg, a special permit is required, only indivisible loads possible!!! The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Country of registration: Germany with Dekra approval and expert opinion, for max. 60 km/h registration, towing vehicle LoF, (max. 40 km/h possible in Switzerland) Prepared for two-line license plate holder without contour marking / reflective strips according to ECE R 048, Paint finish Frame DB 7350 nova gray 10-year warranty against rusting through Drawbar Galvanized or black, manufacturer's choice Drive-on ramps Hot-dip galvanized Attention: Archive pictures!

Condition: new, machine/vehicle number: 6e7907b4000c16661fa1c8a1f, empty load weight: 4,150 kg, maximum load weight: 30,850 kg, overall weight: 35,000 kg, axle configuration: 3 axles, tire size: 385/65 r22.5, Further information Chassis tipper semi-trailer Fine-grained steel welded construction, lightweight design, fifth wheel plate with interchangeable 2 kingpins Curved front end Patented Without support leg Wheel chocks with holder Underride guard, foldable Half-shell mudguards Integrated mudguard holder Stone-repellent surface Tow hook at the rear Axles+suspension SAF disc brake axles Axle/chassis laser-measured Reduction of tire wear and fuel consumption Air suspension 1st axle automatic lift axle, including forced lowering and starting aid, actuation of 3x brakes (starting aid is functional up to an axle load excess of 30% and up to a speed of max. 25 km/h) Hot-dip galvanized lift axle mechanism 10-year warranty against rusting through Brake system 2-line compressed air brake systemColor-coded cable routing for easy servicing. Spring-loaded parking brake 2 interchangeable front clutch heads, without connecting line EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Cjdpfx Afei Ri Aredsgn with lifting & lowering valve Vehicle stability system Wheels and tires 385/65 R22.5 tires of the manufacturer's choice Polished aluminum rims, manufacturer's choice Electrical system 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin socket at the front, without connecting cable Hydraulics Low-pressure cylinder max. 170 bar, smallest stage hard-chlorinated, with HDK screw socket, fixed part, NW 48 mm (without hose connection). Hydraulic actuation via truck power take-off Troughs Aluminum box body made of high-quality, abrasion-resistant 5 mm thick front wall, with external walls made of 30 mm hollow chamber profiles, cleanly welded, with bulk material-repellent top rail profile. Inside with access to front wall (not in conjunction with Cramaro). Shovel and brush holder on the outside of the front wall. Greenline - conical and aerodynamic trough shape Membrane rear wall Rear wall as swing flap with double-jointed hinge, resting on the outside with double hook lock. Rear panel with rubber sealNote! Heat-resistant up to max. 170°C! Floor 5 mm thick throughout, Brinell 110Note! Only for transporting sand, grit and rolled gravel with a maximum grain size of up to 20 mm! All other transport goods are excluded from the warranty! Standing platform with step, connection plate for air/electric and brake with large clearance for best possible operability. Roller tarpaulin on one side for depositing in FR-right, with central locking in FR-left Operating instructions For salt, lime, etc. We recommend a tipping cylinder with a hard chrome-plated piston rod so that it is not attacked by the material and rusts. The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and castering behavior possible due to incorrect load distribution) Revolution Link: Revolution Link experience report: Country of registration / plates Germany with Dekra approval and expert opinion (according to §13 EG - FGV) 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white at the sides and red at the rear Paint finish Frame DB 7350 nova gray Body R

Condition: new, machine/vehicle number: 15431365fe5515297a6a9fb05, overall weight: 24,000 kg, axle configuration: > 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction Turntable with powerful ball bearing slewing ring Folding rear support 2 wheel chocks with holder Aluminum side bumpers Rear spray flaps across the entire width Half-shell mudguards 1st + 2nd axle with anti-spray flaps behind each axle, anti-spray flaps in front of and behind 3rd and 4th axle Excavator trough above the rear axles starting to the rear, approx. 1800 mm long, approx. 650 mm wide and approx. 150 mm deep, 2 pairs of lashing holes each 5 tons in the excavator trough on the side of the longitudinal frame approx. 300 mm from the front and approx. 200 mm in front of the rear slope 1 plastic tool box, with shelf, w=620/h=360/t=440 mm, lockable with a padlock. (lock not included in scope of delivery) 1 storage box on offset recessed in floor with lid, W=720 mm/ L=520 mm / D= 170 mm Extensions extendable to 3,000 mm Wooden planks 70 mm for widening to 3000 mm Storage compartment for wooden planks under the loading area Low loader lashing eyes (40 lashing options) 1 pair of lashing eyes on offset per 5 tons 9 pairs of lashing points at the top and sides, each 10 tons, embedded in the outer frame 2 x front on offset 7 x in the drop deck 6 pairs of lashing holes in the outer frame of the low bed, each with 5 to. (lashing strap attachment) 3 additional pairs of hinged lashing eyes, 10 tons each 1 x inside next to the main frame at the start of the low bed 1 x on offset (protrudes) 1 x embedded in the floor behind the last axle Towing equipment Trailer turntable Drawbar with tested 50 mm drawbar eye, drawbar eye inclined 8° D-value min. 160 kN Axles + suspension Drum brake axles Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation front and rear (rocker compensation) Wheels and tires 235 / 75 R 17,5 at the manufacturer's choice Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 non-interchangeable coupling heads at the front, with connecting cables to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin interchangeable plugs at the front, with connecting cable, 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Offset at the front with steel/ checker plate flooring Then with 70 mm softwood floor, steel/ checker plate covering in the wheel arch area Rear slope with 70 mm softwood flooring Drive-on ramps Cgedpji Ri A Sofx Afdsn Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways covered with wood with spring lift support Country of registration / plates Country of registration: Germany 24/7 service hotline Prepared for two-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white on the sides and red on the rear Warning sign according to ECE - 70 Paintwork Hot-dip galvanized frame incl. passivation 15-year warranty against rusting through Drawbar Galvanized or black, at the manufacturer's discretion Drive-on ramps Hot-dip galvanized Attention! These are archive pictures!

Condition: new, machine/vehicle number: d461243f559015adca5bb372c, overall weight: 24,000 kg, axle configuration: 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction Turntable with powerful ball bearing slewing ring Folding rear support 2 wheel chocks with holder Aluminum side bumpers Rear spray flaps across the entire width Half-shell mudguard 1st axle with anti-spray flapsAnti-spray flaps behind 2nd and 3rd axle 1 plastic tool box, with shelf, w=620/h=360/t=440 mm, lockable with a padlock. Extensions extendable to 3,000 mm Storage compartment for wooden planks in the middle of the loading area Wooden planks 70 mm for widening to 3000 mm Low loader lashing eyes (40 lashing options) 1 pair of lashing cut-outs in the front side member on offset, 10 tons each 4 pairs of lashing holes in the outer frame, 5 tons each (lashing strap attachment) 7 pairs of lashing mushrooms at the top and sides of the outer frame, 10 tons each 1 x front on offset 6 x in the drop deck First lashing eye 250 mm from the front and last max. 250 mm from the rear, distance between lashing eyes not greater than 1100 mm 5 pairs of stake pockets embedded in the outer frame, inside 70 x 40 mm, (can be converted to 5 to. ring lashing eyes) 2 additional pairs of hinged lashing eyes, 10 tons each 1 x on offset (protrudes) 1 x embedded in the floor behind the last axle Trailer drawbar Turntable Drawbar with tested 40 mm drawbar eye Axles + suspension Drum brake axles Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation (rocker compensation) Wheels and tires 235 / 75 R 17,5 at the manufacturer's choice Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 non-interchangeable coupling heads at the front, with connecting cables to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable Make: Wabco, Knorr or Haldex Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable plugs at the front, with connecting cable, 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Front offset with steel/ checker plate covering Storage box recessed into the drive-over slope to the offset Then with 70 mm softwood floor, steel/ checker plate covering in the wheel arch area Rear slope with 70 mm softwood floor Deep loading area incl. rear slope 6,500 mm Drive-on ramps Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways Covered with wood Hydraulic via tractor power take-off with throttle, actuation on the left side in FR Hydraulic connection with SVK plug NW 10/3, incl. connection hose Country of registration / plates Country of registration: Germany 24/7 service hotline Prepared for two-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white on the sides and red on the rear Warning sign according to ECE - 70 Paintwork Cgsdpoi Ri Dljfx Afdon Hot-dip galvanized frame incl. passivation 15-year warranty against rusting through Drawbar Galvanized or black, at the manufacturer's discretion Drive-on ramps Hot-dip galvanized Attention! These are archive pictures!

Condition: new, machine/vehicle number: a0a72d14f9b44bce47bc25ffb, axle configuration: 1 axle, tire size: 11,5/80-15,3 alliance, Further information 40 mm towing eye Support leg with roller Tires: 11.5/80-15.3 Alliance Cjdpfsi Ri D Tox Afdegn without suspension Drawbar eye to center of saddle plate: 3200 mm Tire load capacity 5800kg at 30km/h + 5,150kg at 40km/h Without road approval, for internal use only!

Condition: new, machine/vehicle number: dd98a7658922be8f2e25bcadb, empty load weight: 2 kg, maximum load weight: 8 kg, overall weight: 10 kg, axle configuration: 2 axles, tire size: 235/75 r 17,5, Further information Chassis central axle trailer low bed Fine-grained steel welded construction Telescopic front support leg Telescopic rear support 2 wheel chocks with holder Mudguards made of sheet steel over both wheels Towing device central axle trailer Tow bar with tested 40 mm towing eye Height-adjustable drawbar via spindle, max. adjustment range 250 mm Axles + suspension Euro axles of our choice, with angular roller bearings and S-cam brake Axle/chassis laser-measured Reduction in tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation (rocker compensation) Wheels and tires 235 / 75 R 17,5 manufacturer's choice Factory silver steel rims Brake system 2-line compressed air brake system Spring-applied parking brake 2 interchangeable clutch heads at the front, with connecting cables to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin interchangeable plugs at the front, with connecting cable, TTS bridge Low-lying steel trough, bridge floor made of steel/checker plate covering, steel walls solidly welded to floor Bridge length 4500 mmTub at the front and sides with Load-Lock profile for attaching tensioning straps (8 straps at the front, 12 straps on each side) Note: Slight floor undulation possible due to welding distortion! 2 pairs of lashing eyes, 1 x at the front in the corners of the steel tray and 1 x at the rear in the floor, 5 tons each. 2 additional pairs of lashing eyes in the floor, 5 tons each Drive-on ramps Steel ramps 2 300 mm long, 510 mm wide, can be moved sideways with grab handle on the ramps covered with wood With gas pressure jack for one-man operation Operating instructions The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Country of registration: Germany with Dekra approval and expert opinion (according to §13 EG - FGV) 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white at the sides and red at the rear Paint finish Frame RAL 3002 carmine red Cgjdpfsi Ri Ebox Afdon Hot-dip galvanized drive-on ramps Attention: Archive pictures!

Condition: new, machine/vehicle number: 8e6cf81e11b107f23f22f209a, axle configuration: 3 axles, tire size: 435/50 r19.5, Further information Fine-grained steel welded construction, with preload slight pretension in the neck area, saddle plate with replaceable 2 , kingpin, outer frame slightly inclined new design with Load-Lock profile for tensioning strap attachment, 24 to. 2-speed support winch, single-sided operation, with straight lower section, without thrust compensation Note: Free support leg corner dimension or free swing-through radius to the rear approx. 1930 mm, pull-out ladder at the rear, lateral door stop, 2 wheel chocks with holder, aluminium side collision protection, galvanized steel underride guard, quarter-shell mudguards in front of 1st axle and behind each axle, with anti-spray flaps according to EC, impact protection at the rear SAF disc brake axles, laser-measured axle/chassis to reduce tire wear and fuel consumption, air suspension 2-line compressed air brake system, colored cable routing for easy servicing, spring-loaded parking brake, 2 swap-proof coupling heads at the front, without connecting cable, EBS, electronic brake system with EBS socket at the front, without connecting cable, Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS, with lift & lower valve, vehicle stability system 435/50 R19.5 tires of the manufacturer's choice, steel rims, factory silver 24 volt, multi-chamber lights, amber LED lighting at the sides, 2 white position lights at the front, 2 white/red lane departure lights at the rear, 2 x 7-pin interchangeable sockets at the front, without connecting cable Floor: Screen printing plates approx. 30 mm thick, on longitudinal beams for high point load capacity for forklift axle load up to max. 7100 kg Front bulkhead / corner stanchions: 2,580 mm high, steel corner stanchions in volume design, release device for side tarpaulin on bulkhead, crash blocker, bottom inside at approx. 140 mm height with steel impact protection Center stanchions: 3 pairs of sliding stanchions can be moved along the entire length, with 4 insertion pockets and a long pocket at the bottom, 3 pairs of stanchion positions Insertion slats: 5 rows of wooden insertion slats Rear wall / rear corner stanchions: Rear steel corner stanchions up to the lower edge of the roof, attachment for tarpaulin with round tube and tarpaulin tensioning ratchet, rear portal doors, 2-leaf with 2 internal espagnolette locks each Tarpaulin: Tarpaulin with welded-in horizontal and vertical straps, stainless steel tensioning fasteners Roof: Sliding roof, rear end lift can be folded up, with roof can be pushed from rear to front, L-shaped roof rail for car industry, internal width between the roof rails, approx. 2 490 mm, tarpaulin color: white, 400 Roof non-elastic, hardly any deflection of the roof rail when loading and unloading, optimum rain strip at the rear, at the top of the end bows, above the doors, EcoLift - lifting roof can be raised by approx. 380 mm, with gas pressure damper support, 3 driving positions at the front: interior height at the front approx. 2900 mm/ 2950 mm / 3000 mm, adjusted to approx. 3000 mm Cedpfx Aji Ri E Hefdogn Germany, test approval according to EC 2007/46, 24/7 service hotline, Fliegl manufacturer's certificate for structural strength according to EN 12642 XL, prepared for single-line license plate holder, warning sign according to ECE - 70, reflective strips: white, continuous on the side tarpaulin at the bottom and at the top in the corners (if visible drop sides, then the strip at the bottom, on

Condition: new, machine/vehicle number: a3b1347da4aa7f31dceb875db, empty load weight: 2 kg, maximum load weight: 9 kg, overall weight: 11 kg, axle configuration: 2 axles, tire size: 235 / 75 r 17,5, Further information Chassis central axle trailer Welded fine-grained steel construction 6 pairs of lashing eyes bolted to the outside of the floor/outer frame, 5 tons each Front gear support leg Folding rear support 2 wheel chocks with holder Steel underride guard Rear spray flaps across the entire width Quarter-shell mudguards Towing device central axle trailer Towbar with tested 40 mm towing eye Height-adjustable drawbar via spindle, max. adjustment range 300 mm Axles + suspension BPW drum brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation (rocker compensation) Wheels and tires 235 / 75 R 17,5 manufacturer's choice Factory silver steel rims Brake system 2-line compressed air brake system Hand spindle parking brake Integral air reservoir 2 non-interchangeable coupling heads at the front, with connecting cables to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin interchangeable plugs at the front, with connecting cable, Floor Steel/ checker plate floor for high point load capacity Note: Slight floor corrugation possible due to welding distortion! Cedpfx Afsi Ri Iledogn Platform length approx. 5,200 mm Rear sloping to approx. 900 mm Front wall / front corner stanchions 25 mm aluminum hollow profile, 320 mm high, Drop sides 25 mm aluminum hollow profile, 320 mm high, foldable and removable Rear wall / rear corner stanchions 1 pair of steel stanchions attached to the frame and with bracket for locking the drive-on ramps, drive-in width approx. 2,430 mm Drive-on ramps 2 steel ramps 2 300 mm long, 510 mm wide, can be moved sidewayswith grab handle on the ramps covered with wood With gas pressure jack for one-man operation Operating instructions The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Country of registration: Germany with Dekra approval and expert opinion (according to §13 EG - FGV) 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white at the sides and red at the rear Paint finish Frame DB 7350 nova gray10-year warranty against rusting through Front wall aluminum Side wall anodized aluminium Drive-on ramps Hot-dip galvanized Attention: Archive pictures!

Condition: new, machine/vehicle number: c1946328bb4efe26fccb128ee, empty load weight: 3 kg, maximum load weight: 14 kg, overall weight: 18 kg, axle configuration: 2 axles, tire size: 385 / 55 r 22,5, Further information Chassis Turntable Disposal Fine-grained steel welded construction 2 longitudinal beams with cross beams, upper side of the longitudinal beams designed as container roller tracks in wear-resistant design, loadable from the rear, with ramp. For roll-off containers with 6.5/ 7.0 m. Container locking: - 2 pairs of locking hooks embedded in the floor - pneumatic actuation The container locking is a 2-point design, acting from the inside, and locking of the roll-off containers with inner web is not possible (for transporting roll-off containers with lower frame in accordance with DIN 30722) Turntable with strong ball bearing slewing ring Wheel chocks with holder Aluminum side bumpers Steel underride guard Half-shell mudguards Towing equipment Trailer turntable Drawbar with tested 40 mm drawbar eye Axles+suspension SAF disc brake axles with 430 mm disc diameter Axle/chassis laser-measured Reduction of tire wear and fuel consumption Air suspension Wheels and tires 385 / 55 R 22,5 at the manufacturer's choice Factory silver steel rims Brake system 2-line compressed air brake system Spring-loaded parking brake Immobilizer: the spring-loaded parking brake is activated when the container lock is open Vehicle stability system 2 non-interchangeable coupling heads at the front, with connecting lines to the motor vehicle, EBS, electronic braking system with EBS plug at the front, with connecting cable Cjdei Ri Nmopfx Afdogn Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin interchangeable plugs at the front, with connecting cable, Country of registration / plates Country of registration: Germany with Dekra approval and certificate (according to §13 EG - FGV) 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white at the sides and red at the rear Paint finish Frame DB 7350 nova gray 10-year warranty against rusting through Drawbar KTL black Attention: Archive pictures!

Condition: new, machine/vehicle number: b6e633155abf971a017e4b53b, empty load weight: 3 kg, maximum load weight: 14 kg, overall weight: 18 kg, axle configuration: 2 axles, tire size: 385 / 55 r 22,5, Further information Chassis Turntable Disposal Fine-grained steel welded construction Carriage: Container is placed on the carriage from the rear and pushed forwards, container stop at the front adjustable for 6.0 / 6.5 and 7.0 m roll-off containers with outer roller Container locking mechanism: - 2 pairs of locking hooks embedded in the floor - Pneumatic actuationThe container locking mechanism is a 2-point design that operates from the inside and locking of roll-off containers with an inner web is not possible Codpji Ri Nqsfx Afdsgn Turntable with powerful ball bearing slewing ring Wheel chocks with holder Aluminum side bumpers Steel underride guard Half-shell mudguards Rear impact protection, vertical left and right, with delta rubber on the underride guard holder, Trailer drawbar Turntable Drawbar with tested 40 mm drawbar eye Axles + suspension SAF disc brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Air suspension with lift & lower valve Wheels and tires 385 / 55 R 22,5 manufacturer's choice Factory silver steel rims Brake system 2-line compressed air brake system Spring-applied parking brake Immobilizer: the spring-loaded parking brake is activated when the container lock is open Vehicle stability system 2 non-interchangeable coupling heads at the front, with connecting lines to the motor vehicle, EBS, electronic braking system with EBS plug at the front, with connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red lane departure lights at the rear 1 additional LED work light(s) at the rear, switched via reversing light 2 x 7-pin interchangeable plugs at the front, with connecting cable, Approval / plates Country of registration: Germany with Dekra approval and certificate (according to §13 EG - FGV) 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white at the sides and red at the rear Paint finish Frame DB 7350 nova gray Drawbar KTL black Attention: Archive pictures!

Condition: new, machine/vehicle number: e8628b18bda6db44719c946e0, overall weight: 18,000 kg, axle configuration: 2 axles, tire size: 385/65 r22.5, Further information Chassis Changing turntable Fine-grained steel welded construction Fliegl V-Stream frame Front stop, longitudinally adjustable and foldable 2 pairs of removable guide rollers, front and rear 4 container locks with sturdy outriggers on 20-basefor swap bodies 7.15 and 7.45 Turntable with strong ball bearing slewing ring 2 wheel chocks with holder Aluminum side bumper Side collision protection set inwards, for optimum clearance to the swap body supports Steel underride guard Underride guard shortened for optimum clearance to the swap body supports, lighting system mounted protected Half-shell mudguards Towing equipment Trailer turntable Drawbar with tested 40 mm drawbar eye Drawbar height adjustment via spring Axles + suspension SAF disc brake axles with 430 mm disc diameter Axle/chassis laser-measured Reduction of tire wear and fuel consumption Air suspension Brake system 2-line compressed air brake systemColor-coded line routing for easy servicing. Air supply 208 liters Spring-loaded parking brake 2 swap-proof coupling heads at the front, with connecting lines to the motor vehicle, EBS, electronic brake system with EBS plug at the front, with connecting cable, Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve, holding function in both lowering and lifting position Wheels and tires 385/65 R22.5 make of the manufacturer's choice Steel rims, factory silver Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable plugs at the front, with connecting cable, 2 additional LED work lights at the rear, switched via reversing light 1 LED work light at the front, centered between the carriers, radiating to the rear, switched via reversing light Country of registration/ plates Germany with Dekra approval and certificate (according to §13 EG - FGV) 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white at the sides and red at the rear Paint finish Frame DB 7350 nova gray 10-year warranty against rusting through Cgjdpsi Rivlofx Afdon Please note! These are archive images!

Condition: new, machine/vehicle number: f044065451f6d849ee7a5b9f8, empty load weight: 5 kg, maximum load weight: 29 kg, overall weight: 35 kg, axle configuration: 3 axles, tire size: 385 / 65 r 22,5, Further information Chassis semi-trailer forwarding Welded steel construction in reinforced design, only 2 side members as double T-beams with steel/checker plate between the side members, saddle plate with replaceable 2 kingpins. Protective plate for rear lights. 1 steel storage box, recessed between side members 8 pairs of lashing eyes bolted or welded to the frame at the manufacturer's choice 24 t. 2-speed support winch, single-sided operation, with straight lower section, without thrust compensation 2 wheel chocks with holder Aluminium side bumper Galvanized steel underride guard Half-shell mudguards with anti-spray flaps according to EC 1 spare wheel holder for 1 e-wheel, with wheel fastening set 8 wooden stanchions of the manufacturer's choice, bolted to frame with 2 wooden stanchions each, telescopic from 1800 to 2800 mm, per pair 7 to. Cgedpsi Rivwsfx Afdon Axles + suspension SAF disk brake axles with 430 mm disk diameter Air suspension with lifting & lowering valve, safety cable on the axles 1st axle automatic lift axle, including forced lowering and starting aid, actuation of 3x brakes (starting aid is functional up to an axle load excess of 30% and up to a speed of max. 25 km/h) Axle spacing offset mm (combined transport) up to 44 tons gross train weight Wheels and tires 385 / 65 R 22,5 at the manufacturer's discretion Steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake Axle load detection via EBS-Canbus signal, for indication via display in the cab, truck must be prepared accordingly, no truck installed (no calibrated scales) 2 swap-proof coupling heads at the front, without connecting cable EBS, electronic brake system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin and 1 x 15-pin interchangeable sockets at the front, without connecting cable Front bulkhead/front stanchions Steel/grid bulkhead, approx. 2,300 mm high, bolted to the frame Approval / plates Country of approval: Germany Approval according to EC 2007/46 Prepared for single-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white at the sides and red at the rear Paint finish Frame DB 7350 nova gray Black coated support legs Front wall hot-dip galvanized Attention: Archive pictures!

Condition: new, machine/vehicle number: d7a33d709a92cd60f18d010e8, empty load weight: 3 kg, maximum load weight: 14 kg, overall weight: 18 kg, axle configuration: 2 axles, tire size: 385/65 r22.5, Further information Chassis Wechel central axle trailer Fine-grained steel welded construction Front stop, longitudinally adjustable and foldable 2 pairs of removable guide rollers, front and rear 4 container locks with sturdy outriggers on 20-basefor swap bodies 7.15 and 7.45 1 pair of front gear support legs, with straight lower section and single-sided operation in FR right 2 wheel chocks with holder Aluminum side impact guard Side collision protection set inwards, for optimum clearance to the swap body supports Steel underride guard Half-shell mudguards Spray flaps Towing device central axle trailer Drawbar with tested 50 mm towing eye, forwarding agent version (not suitable for trucks with tail lift, or precise testing still required in the event of an order) Axles + suspension SAF disc brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Air suspension Brake system 2-line compressed air brake systemColor-coded line routing for easy servicing. Air supply 208 liters Spring-loaded parking brake 2 swap-proof coupling heads at the front, with connecting lines to the engine trolley, connection in FR right-hand side EBS, electronic brake system with EBS plug at the front, with connecting cable, connection in FR right-hand side Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve, holding function in both lowering / lifting position Wheels and tires 385/65 R22.5 Athos brand Steel rims, factory silver Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red rear lane departure lights Cjdpfx Aoi Riwbsfdogn 1 x 15-pin plug at the front, with connecting cable, connection in FR right-hand side 2 additional LED work lights, integrated at the rear, switched via reversing light 1 LED work light at the front, centered between the carriers, radiating to the rear, switched via reversing light Operating instructions The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Germany with Dekra approval and expert opinion (according to §13 EG - FGV) 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white at the sides and red at the rear Paint finish Frame DB 7350 nova gray 10-year warranty against rusting through Attention: Archive pictures!

Condition: new, machine/vehicle number: bdf30cb8a53c70e900bdb40a7, empty load weight: 2 kg, maximum load weight: 9 kg, overall weight: 11 kg, axle configuration: 2 axles, tire size: -, Further information Chassis central axle tipping trailer Welded steel construction, continuous tipping shaft at the rear with 80 mm ball tipping bearing Gearbox support foot at the front 2 wheel chocks with holder Steel underride guard Rear splash guards across the entire width Quarter-shell mudguards Lockable storage space for access ramps underneath the loading area Towing device central axle trailer Tow bar with tested 40 mm towing eye Height-adjustable drawbar via spindle, max. adjustment range 300 mm Axles + suspension BPW drum brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation (rocker compensation) Wheels and tires Cgsdpfsi Riwiox Afden 235 / 75 R 17,5 manufacturer's choice Factory silver steel rims Brake system 2-line compressed air brake systemColor-coded cable routing for easy servicing. Hand spindle parking brake Integral air reservoir ABS and ALB, with ABS plug at the front, with connecting cable, Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! 2 swap-proof coupling heads at the front, with connecting cables to the motor vehicle, Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin non-interchangeable plugs at the front, with connecting cable, Hydraulics Three-way tipping mechanism, hydraulic multi-piston press with lift limiter and safety cable, Low-pressure cylinder up to max. 170 bar, without throttle. If necessary, this must be retrofitted to the truck. Hydraulic connection with SVK plug NW 10/3, incl. connection hose Hydraulic actuation via truck power take-off Tilting bridges Sturdy tipper body with 4 mm sheet steel floor, steel side wall structure, continuous side walls, hinged and pivoted with central locking at the bottom. Rear corner stanchions pluggable. Rear wall can be folded down and pivoted, with central locking at the bottom. Platform length approx. 4,500 mm, side walls with 5 hinges at the bottom. Platform width 2420 mm 5 pairs of lashing eyes in the floor, 5 tons each Operating instructions The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Country of registration: Germany with Dekra approval and expert opinion (according to §13 EG - FGV) 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white at the sides and red at the rear Paintwork Hot-dip galvanized frame incl. passivation 15-year warranty against rusting through Dropside/bridge RAL 3002 carmine red Rear support, access ramps, storage box are optionally available at extra cost Attention: Archive pictures

Condition: new, machine/vehicle number: 068983c41e44eb5660fa9100c, empty load weight: 6 kg, maximum load weight: 28 kg, overall weight: 35 kg, axle configuration: 3 axles, tire size: 435/50 r19,5, Further information Chassis saddle forwarding Fine-grained steel welded construction, with preload slight pre-tensioning in the neck area, saddle plate with replaceable 2 kingpins X-tra Long, with 15030 mm internal length Outer frame slightly inclined new design with Load-Lock profile for tensioning strap attachment 24 to. 2-speed support winch, single-sided operation, with straight lower section, without thrust compensation Note: Free support leg corner dimension or free swing-through radius to the rear approx. 1930 mm Extension ladder at the rear Door retainer at the side 2 wheel chocks with holder Aluminium side bumper Cjdsi Riwuspfx Afdogn Galvanized steel underride guard Quarter-shell mudguards in front of 1st axle and behind each axle Impact protection at the rear Axles + suspension SAF disc brake axles Axle/chassis laser-measured Reduction of tire wear and fuel consumption Air suspension Brake system 2-line compressed air brake system Colored line routing for easy service. Spring-loaded parking brake 2 interchangeable clutch heads at the front, without connecting cable EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve Vehicle stability system AAC Basic, automatic relief axle acting on last axle, as maneuvering aid, up to 20 km/h, can be switched off manually Axle load detection via EBS-Canbus signal, for indication via display in driver's cab, truck must be prepared accordingly, no truck installation (no calibrated scales) Wheels and tires 435/50 R19.5 tires of the manufacturer's choice Steel rims, factory silver Electrical system 24 volt, multi-chamber lights, amber LED lighting on the side Side amber LED lighting coupled with the blinker Flashing side lights Side lights 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable sockets at the front, without connecting cable Floor Screen printing plates approx. 30 mm thick, on longitudinal beams for high point load capacity for forklift axle load up to max. 7100 kg Front wall / front corner stanchions 2,580 mm high, steel corner stanchions in volume design, release device for side tarpaulin on bulkhead, crash blocker, bottom inside at approx. 140 mm height with steel impact protection Center stanchions 3 pairs of sliding stanchions can be moved along the entire length, with 4-fold pockets and with long pocket at the bottom. 3 pairs of stanchion positions Insertion slats 5 rows of wooden slats Rear wall / rear corner stanchions Rear corner stanchions steel up to lower edge of roof, attachment for tarpaulin with round tube and tarpaulin tensioning ratchet Rear portal doors, 2-leaf with 2 internal espagnolette locks each Tarpaulin Tarpaulin, with welded-in horizontal and vertical straps Stainless steel tension locks Roof Sliding roof, rear end lift can be folded up, with roof can be pushed from rear to front, L-shaped roof rail for automotive industry, internal width between the roof rails approx. 2,490 mm, tarpaulin color: white Roof non-elastic, hardly any deflection of the roof rail when loading and unloading EcoLift - lifting roof can be raised by approx. 380 mm, on both sides, with gas pressure damper support, 3 driving positions at the front: Front interior height approx. 2900 mm / 2950 mm / 3000 mm, adjusted to approx. 3000 mm Optimum rain strip at the rear, at the top of the end bows,

Condition: new, machine/vehicle number: 2f960ff7c44de83fd060ec5df, empty load weight: 6,750 kg, maximum load weight: 28,250 kg, overall weight: 35,000 kg, axle configuration: 3 axles, tire size: 385/65 r22,5, Further information Chassis tipper semi-trailer Fine-grained steel welded construction, in basic lightweight design, fifth wheel plate with interchangeable 2 kingpins Curved front end Patented 24 t. 2-speed support winch, single-side operation, with straight lower section, without thrust compensation Cgsdpfxsi Rizfo Afdon Wheel chocks with holder Underride guard, folding Half-shell mudguards Integrated mudguard holder Stone-repellent surface With anti-spray flaps on last axle only Tarpaulin pole with bracket Tow hook at the rear Axles+suspension SAF disc brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Axles in off-road version, Air suspension 1st axle automatic lift axle, including forced lowering and starting aid, actuation of 3x brakes (starting aid is functional up to an axle load excess of 30% and up to a speed of max. 25 km/h) Hot-dip galvanized lift axle mechanism 10-year warranty against rusting through Brake system 2-line compressed air brake systemColor-coded cable routing for easy servicing. Spring-loaded parking brake 2 interchangeable front clutch heads, without connecting line EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve Vehicle stability system Wheels and tires 385/65 R22.5 Steel rims, factory silver Electrical system 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable sockets at the front, without connecting cable Hydraulics Low-pressure cylinder max. 170 bar, smallest stage hard-chlorinated, with HDK screw socket, fixed part, NW 48 mm (without hose connection) Hydraulic actuation via truck power take-off Troughs Round steel body in light Master Agrar design made of highly wear-resistant HB 400/450 steel. Sloping front wall with external hydraulic en with access to front wall. Greenline - conical and aerodynamic body shape Bucket and brush holder on the outside of the front wall. Membrane rear wall Aluminum rear wall on pendulum bearings with double-joint hinge and with 2-leaf door division 1/2 to 1/2, top with swinging gallows, with one grain slider per door. With external espagnolette lock and mechanical locking at the bottom, Side walls 3 mm thick throughout, base 3 mm thick throughout, wear and weight-optimized design, Standing platform with ladder, connection plate for air/electric and brake with large clearance for best possible operability. Roller tarpaulin on one side for depositing in FR-right, with central locking in FR-left Operating instructions For salt, lime, etc. We recommend a tipping cylinder with a hard chrome-plated piston rod so that it is not attacked by the material and rusts. The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Germany Test approval according to EC 2007/46 Body strength according to EN 12642 24/7 service hotline Prepared for single-line license plate holder Warning sign according to ECE - 70 Contour markings with reflective strips to ECE R 048, white at the sides and red at the rear Paint finish Frame DB 7350 nova gray10 J

Condition: used, machine/vehicle number: 266c1faf254aacf5bd0b3713c, empty load weight: 2,400 kg, maximum load weight: 11,000 kg, overall weight: 13,400 kg, axle configuration: 2 axles, first registration: 03/2014, tire size: 285/70 r19,5, Year of construction: 2014, Further information Fine-grained steel welded construction, fifth wheel coupling, make of our choice for 2\ kingpin with ball bearing slewing ring, stop max. 20°, telescopic support foot, 2 wheel chocks with holder, steel underride guard, half-shell mudguards CLG under-coupler drawbar with tested 50 mm drawbar eyes to the dolly and to the motor vehicle. BPW disc brake axles, air suspension with lift & lower valve 2-line compressed air brake system, spring-loaded parking brake, Duomatic front coupling head, with connecting lines to the tractor unit2 interchangeable coupling heads to the trailer Cgedpfx Aei Rizmjfdsn EBS, electronic braking system with EBS plug at the front, with connecting cable, Can RouterEBS connecting cable to the trailer, Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Axle load detection for trucks via EBS, without truck instal. 24 volt, multi-chamber LED lights, amber LED lighting at the sides, 2 white LED position lights at the front 2 white/red rear lane departure warning lights in LED, 1 x 15-pin plug at the front, with connecting cable to the truck 1 x 15-pin plug with connecting cable to the trailer, cable routing for camera system Country of registration: Germany, with Dekra approval, prepared for single-line license plate holder, contour marking with reflective strips in accordance with ECE R 048, white at the sides and red at the rear Saddle height approx.: 1150 mm

Condition: new, machine/vehicle number: 628cde0fe99cc2d3c8eaa8dd8, overall weight: 24,000 kg, axle configuration: 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction Turntable with powerful ball bearing slewing ring Folding rear support 2 wheel chocks with holder Aluminum side bumpers Rear spray flaps across the entire width Half-shell mudguard 1st axle with anti-spray flapsAnti-spray flaps behind 2nd and 3rd axle Cedpfx Aoi Ri Ddofdogn 1 plastic tool box, with shelf, w=620/h=360/t=440 mm, lockable with a padlock. (lock not included in scope of delivery) Extensions extendable to 3,000 mm Storage compartment for wooden planks in the middle of the loading area Wooden planks 70 mm for widening to 3000 mm Low loader lashing eyes (40 lashing options) 1 pair of lashing cut-outs in the front side member on offset, 10 tons each 4 pairs of lashing holes in the outer frame, 5 tons each (lashing strap attachment) 7 pairs of lashing points at the top and sides of the outer frame, 10 tons each 1 x front on offset 6 x in the drop deck First lashing eye 250 mm from the front and last max. 250 mm from the rear, distance between lashing eyes not greater than 1100 mm 5 pairs of stake pockets embedded in the outer frame, inside 70 x 40 mm, (can be converted to 5 to. ring lashing eyes, not included in the scope of delivery) 2 additional pairs of hinged lashing eyes, 10 tons each 1 x on offset (protrudes) 1 x embedded in the floor behind the last axle Trailer drawbar Turntable Drawbar with tested 40 mm drawbar eye Axles + suspension Drum brake axles, at the manufacturer's choice Axle/chassis laser-measured Reduction of tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation (rocker compensation) Wheels and tires 235 / 75 R 17,5 at the manufacturer's discretion Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 non-interchangeable coupling heads at the front, with connecting cables to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable Make: Wabco or Knorr Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable plugs at the front, with connecting cable, 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Front offset with steel/ checker plate covering Storage box recessed into the drive-over slope to the offset Then with 70 mm softwood floor, steel/ checker plate covering in the wheel arch area Rear slope with 70 mm softwood floor Deep loading area incl. rear slope 6,500 mm Drive-on ramps Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways covered with wood with spring lift support Country of registration / plates Country of registration: Germany 24/7 service hotline Prepared for two-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white on the sides and red on the rear Warning sign according to ECE - 70 Paintwork Hot-dip galvanized frame incl. passivation 15-year warranty against rusting through Drawbar Galvanized or black, at the manufacturer's discretion Drive-on ramps Hot-dip galvanized Attention! These are archive pictures!

Condition: new, machine/vehicle number: abc6276e1749f9dddc494eb32, empty load weight: 4,900 kg, maximum load weight: 30,100 kg, overall weight: 35,000 kg, axle configuration: 3 axles, tire size: 385/65 r22,5², Further information Chassis tipper semi-trailer Fine-grained steel welded construction, lightweight design, fifth wheel plate with interchangeable 2 kingpins Curved front end Patented Telescopic support in the middle, unhitching with load not possible, when unhitched the vehicle must be at an angle to the rear. 2 wheel chocks with holder Folding underride guard Half-shell mudguards Integrated mudguard holder Stone-repellent surface with anti-spray flaps on last axle only 1 tarpaulin pole with bracket 2 towing hooks at the rear Axles+suspension SAF disc brake axles with 430 mm disc diameter Axle/chassis laser-measured Reduction in tire wear and fuel consumption Axles in off-road version, Air suspension 1st axle automatic lift axle, including forced lowering and starting aid, actuation of 3x brakes (starting aid is functional up to an axle load excess of 30% and up to a speed of max. 25 km/h) Hot-dip galvanized lift axle mechanism 10-year warranty against rusting through Brake system 2-line compressed air brake systemColor-coded cable routing for easy servicing. Spring-loaded parking brake 2 interchangeable front clutch heads, without connecting line EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve Vehicle stability system Automatic tilt lowering with shut-off valve Cgedpoi Ri H Iefx Afdjn Wheels and tires 385/65 R22.5 tires of the manufacturer's choice Steel rims, factory silver Electrical system 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable sockets at the front, without connecting cable Hydraulics Low-pressure cylinder max. 170 bar, smallest stage hard-chlorinated, with HDK screw socket, fixed part, NW 48 mm (without hose connection). Hydraulic actuation via truck power take-off Troughs Aluminum box body made of high-quality, abrasion-resistant 5 mm thick front wall, with external walls made of 30 mm hollow chamber profiles, cleanly welded, with bulk material-repellent top rail profile. Inside with access to front wall (not in conjunction with Cramaro). Shovel and brush holder on the outside of the front wall. Greenline - conical and aerodynamic trough shape Membrane rear wall Rear wall as swing flap with double-jointed hinge, resting on the outside with double hook lock. Rear panel with rubber sealNote! Heat-resistant up to max. 170°C! Floor 6 mm thick throughout Standing platform with access, connection plate for air/electric and brake with large clearance for best possible operability. Roller tarpaulin on one side for depositing in FR-right, with central locking in FR-left Operating instructions For salt, lime, etc. We recommend a tipping cylinder with a hard chrome-plated piston rod so that it is not attacked by the material and rusts. The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Germany Test approval according to EC 2007/46 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips according to ECE R 048, white on the sides and red on the rear

Condition: new, machine/vehicle number: 074630ca1b8dc2d710f82c15a, empty load weight: 3,980 kg, overall weight: 35,000 kg, axle configuration: 3 axles, tire size: 385/65 r22.5, Further information Chassis tipper semi-trailer Fine-grained steel welded construction, lightweight design, fifth wheel plate with interchangeable 2 kingpins Curved front end Patented Without support leg Wheel chocks with holder Underride guard, foldable Half-shell mudguards Integrated mudguard holder Stone-repellent surface Tow hook at the rear Axles+suspension SAF disc brake axles Axle/chassis laser-measured Reduction of tire wear and fuel consumption Air suspension 1st axle automatic lift axle, including forced lowering and starting aid, actuation of 3x brakes (starting aid is functional up to an axle load excess of 30% and up to a speed of max. 25 km/h) Hot-dip galvanized lift axle mechanism 10-year warranty against rusting through Brake system 2-line compressed air brake systemColor-coded cable routing for easy servicing. Spring-loaded parking brake 2 interchangeable front clutch heads, without connecting line EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve Vehicle stability system Wheels and tires 385/65 R22.5 tires of the manufacturer's choice Cgsdpji Ri H Ssfx Afdjn Polished aluminum rims, manufacturer's choice Electrical system 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin socket at the front, without connecting cable Hydraulics Low-pressure cylinder max. 170 bar, smallest stage hard-chlorinated, with HDK screw socket, fixed part, NW 48 mm (without hose connection). Hydraulic actuation via truck power take-off Troughs Aluminum box body made of high-quality, abrasion-resistant 5 mm thick front wall, with external walls made of 30 mm hollow chamber profiles, cleanly welded, with bulk material-repellent top rail profile. Inside with access to front wall (not in conjunction with Cramaro). Shovel and brush holder on the outside of the front wall. Greenline - conical and aerodynamic trough shape Membrane rear wall Rear wall as swing flap with double-jointed hinge, resting on the outside with double hook lock. Rear panel with rubber sealNote! Heat-resistant up to max. 170°C! Floor 5 mm thick throughout, Brinell 110Note! Only for transporting sand, grit and rolled gravel with a maximum grain size of up to 20 mm! All other transport goods are excluded from the warranty! Standing platform with step, connection plate for air/electric and brake with large clearance for best possible operability. Roller tarpaulin on one side for depositing in FR-right, with central locking in FR-left Operating instructions For salt, lime, etc. We recommend a tipping cylinder with a hard chrome-plated piston rod so that it is not attacked by the material and rusts. The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and castering behavior possible due to incorrect load distribution) Revolution Link: Revolution Link experience report: Country of registration / plates Germany with Dekra approval and expert opinion (according to §13 EG - FGV) 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white at the sides and red at the rear Paint finish Frame DB 7350 nova gray Body R

Condition: new, machine/vehicle number: 45d76d32267904923b7adcdea, empty load weight: 4,980 kg, maximum load weight: 30,020 kg, overall weight: 35,000 kg, axle configuration: 3 axles, tire size: 385/65 r22.5, Further information Chassis tipper semi-trailer Fine-grained steel welded construction, lightweight design, fifth wheel plate with interchangeable 2 kingpins Curved front end Patented 24 t. 2-speed support winch, single-side operation, with straight lower section, without thrust compensation Wheel chocks with holder Underride guard, folding Half-shell mudguards Integrated mudguard holder Surface stone-repellent Tow hook at the rear Axles+suspension SAF disc brake axles Axle/chassis laser-measured Reduction of tire wear and fuel consumption Air suspension 1st axle automatic lift axle, including forced lowering and starting aid, actuation of 3x brakes (starting aid is functional up to an axle load excess of 30% and up to a speed of max. 25 km/h) Csdpji Ri Idjfx Afdjgn Hot-dip galvanized lift axle mechanism 10-year warranty against rusting through Brake system 2-line compressed air brake systemColor-coded cable routing for easy servicing. Spring-loaded parking brake 2 interchangeable front clutch heads, without connecting line EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve Vehicle stability system Wheels and tires 385/65 R22.5 tires of the manufacturer's choice Polished aluminum rims, manufacturer's choice Electrical system 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin socket at the front, without connecting cable Hydraulics Low-pressure cylinder max. 170 bar, smallest stage hard-chlorinated, with HDK screw socket, fixed part, NW 48 mm (without hose connection). Hydraulic actuation via truck power take-off Troughs Aluminum box body made of high-quality, abrasion-resistant 5 mm thick front wall, with external walls made of 30 mm hollow chamber profiles, cleanly welded, with bulk material-repellent top rail profile. Inside with access to front wall (not in conjunction with Cramaro). Shovel and brush holder on the outside of the front wall. Greenline - conical and aerodynamic trough shape Membrane rear wall Rear wall as swing flap with double-jointed hinge, resting on the outside with double hook lock. Rear panel with rubber sealNote! Heat-resistant up to max. 170°C! Floor 5 mm thick throughout, Brinell 110Note! Only for transporting sand, grit and rolled gravel with a maximum grain size of up to 20 mm! All other transport goods are excluded from the warranty! Standing platform with step, connection plate for air/electric and brake with large clearance for best possible operability. Roller tarpaulin on one side for depositing in FR-right, with central locking in FR-left Operating instructions For salt, lime, etc. We recommend a tipping cylinder with a hard chrome-plated piston rod so that it is not attacked by the material and rusts. The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and castering behavior possible due to incorrect load distribution) Revolution Link: Revolution Link experience report: Country of registration / plates Germany with Dekra approval and expert opinion (according to §13 EG - FGV) 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips according to ECE R 0

Condition: new, machine/vehicle number: efdaf8862775f9506d97b86a5, empty load weight: 5,600 kg, maximum load weight: 29,400 kg, overall weight: 35,000 kg, axle configuration: 3 axles, tire size: 385/65 r22,5², Further information Chassis tipper semi-trailer Fine-grained steel welded construction, lightweight design, fifth wheel plate with interchangeable 2 kingpins Curved front end Patented 24 t. 2-speed support winch, single-side operation, with straight lower section, without thrust compensation 2 wheel chocks with holder Underride guard, folding Half-shell mudguards Integrated mudguard holder Stone-repellent surface With anti-spray flaps on last axle only 1 tarpaulin pole with bracket 2 towing hooks at the rear Axles+suspension SAF disc brake axles with 430 mm disc diameter Axle/chassis laser-measured Reduction in tire wear and fuel consumption Axles in off-road version, Air suspension 1st axle automatic lift axle, including forced lowering and starting aid, actuation of 3x brakes (starting aid is functional up to an axle load excess of 30% and up to a speed of max. 25 km/h) Cgedpfx Afei Ri Ihodon Hot-dip galvanized lift axle mechanism 10-year warranty against rusting through Brake system 2-line compressed air brake systemColor-coded cable routing for easy servicing. Spring-loaded parking brake 2 interchangeable front clutch heads, without connecting line EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve Vehicle stability system Wheels and tires 385/65 R22.5 tires of the manufacturer's choice Steel rims, factory silver Electrical system 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable sockets at the front, without connecting cable Hydraulics Low-pressure cylinder max. 170 bar, smallest stage hard-chlorinated, with HDK screw socket, fixed part, NW 48 mm (without hose connection). Hydraulic actuation via truck power take-off Troughs Aluminum box body made of high-quality, abrasion-resistant 5 mm thick front wall, with external walls made of 30 mm hollow chamber profiles, cleanly welded, with bulk material-repellent top rail profile. Inside with access to front wall (not in conjunction with Cramaro). Shovel and brush holder on the outside of the front wall. Greenline - conical and aerodynamic trough shape Membrane rear wall Rear wall pendulum-mounted with double-joint hinge and with 2-leaf door partition 1/2 to 1/2, with pivoting gallows at the top, with one grain slider per door. Rear panel with rubber sealNote! Heat-resistant up to max. 170°C! Floor 6 mm thick throughout Standing platform with access, connection plate for air/electric and brake with large clearance for best possible operability. Roller tarpaulin on one side for depositing in FR-right, with central locking in FR-left Operating instructions For salt, lime, etc. We recommend a tipping cylinder with a hard chrome-plated piston rod so that it is not attacked by the material and rusts. The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Germany Test approval according to EC 2007/46 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips according to ECE R 048, white on the sides and red on the rear Paint finish Frame DB 7350 Novagr

Condition: new, machine/vehicle number: 55d3c5c03e032385649769b1b, empty load weight: 9,900 kg, maximum load weight: 14,100 kg, overall weight: 24,000 kg, axle configuration: > 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction Turntable with strong ball bearing slewing ring, storage box recessed in Incl. Turntable front end Folding rear support 2 wheel chocks with holder Aluminum side bumper Rear spray flaps across the entire width Widenings extendable to 3,000 mm (not in rear slope) (However, the track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Storage compartment for wooden planks in the middle of the cargo bed Wooden planks 70 mm for widening to 3000 mm Low loader lashing eyes 3 pairs of lashing points, 10 tons each, integrated in the floor at the front 6 pairs of lashing points at the top and sides, each 10 tons, integrated in the outer frame 1 x to the neck area remaining distributed in between Spacing not greater than 1200 mm 1 x rear slope 5 pairs of stake pockets embedded in the outer frame, inside 70 x 40 mm, (can be converted to 5 to. ring lashing eyes, not included in the scope of delivery) Towing equipment Trailer turntable Cgjdpfsi Ri I Eox Afdsn Drawbar with tested 40 mm towing eye Please note! With 40 mm drawbar eye, the maximum permissible total weight of the truck is 18000 kg, otherwise 50 mm drawbar eye required. Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation front and rear (rocker compensation) Wheels and tires 235 / 75 R 17,5 at the manufacturer's choice Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 non-interchangeable coupling heads at the front, with connecting cables to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin interchangeable plugs at the front, with connecting cable, 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Front area steel floor, then with 70 mm softwood floor, steel/checker plate flooring in the wheel housing area Rear slope with 70 mm softwood floor Drive-on ramps Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways covered with wood with spring jack support Operating instructions With an axle load of 10,000 kg, a special permit is required, only indivisible loads possible!!! The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Country of registration: Germany 1 with Dekra approval and expert opinion (according to §13 EG - FGV) 24/7 service hotline Prepared for two-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white at the sides and red at the rear Paint finish Frame Ral 3002 carmine red 10-year warranty against rusting through Drawbar Galvanized or black, at the manufacturer's choice Drive-on ramps Hot-dip galvanized Attention: Archive pictures!

Condition: new, machine/vehicle number: 8df1ead53cc82aeb51e50a37d, empty load weight: 4 kg, maximum load weight: 13,880 kg, overall weight: 18 kg, axle configuration: 2 axles, tire size: 235 / 75 r 17,5, Further information Chassis Turntable Disposal Fine-grained steel welded construction Container locking system: - 2 pairs of locking hooks embedded in the floor - Pneumatic actuation The container locking mechanism is a 2-point design, acting from the inside, and locking of roll-off containers with an inner web is not possible (for transporting roll-off containers with a sub-frame in accordance with DIN 30722) Note! At the start of the roller recess at the front, the container must be pushed on completely flat! Longitudinal guide rails can be moved sideways and removed, rails approx. 115 mm high Turntable with strong ball bearing slewing ring 8 pairs of lashing mushrooms at the top and sides of the outer frame, 5 tons each 7 pairs of stake pockets embedded in the outer frame, inside 70 x 40 mm, (can be converted to 5 to. ring lashing eyes, not included) 2 wheel chocks with holder Aluminum side bumpers Steel underride guard Quarter-shell mudguards according to EG with anti-spray flaps according to EG Towing equipment Trailer turntable Cgodpfx Afsi Ri Nusdsn Drawbar with tested 40 mm drawbar eye Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction of tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings Wheels and tires 235 / 75 R 17,5 at the manufacturer's choice Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 non-interchangeable coupling heads at the front, with connecting cables to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin interchangeable plugs at the front, with connecting cable, floor Steel floor Roller recess for container recessed in the floor at the frontfor roll-off containers from 5,000 - 7,000 mm in length Note: Slight floor undulation possible due to welding distortion! Drive-on ramps Lockable storage space for loading ramps underneath the loading area Operating instructions A special permit is required for axle loads of 10,000 kg. Approval must be applied for individually in each federal state; the legislator does not have to grant approval for 20 t GG. Customer risk. The specified total weight is technically possible; depending on the load, the total weight may not be achieved while complying with the permissible axle/support and fifth-wheel loads. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Country of registration: Germany with Dekra approval and expert opinion (according to §13 EG - FGV) 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white at the sides and red at the rear Warning sign according to ECE - 70 Paint finish Frame DB 7350 nova gray 15-year warranty against rusting through Note: Bottom corrugation possible due to hot-dip galvanizing! Drawbar KTL black Attention: Archive pictures!

Condition: new, machine/vehicle number: 6d88bda3a1ee2464a81b34f36, empty load weight: 4 kg, maximum load weight: 13 kg, overall weight: 18 kg, axle configuration: 2 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction, with slight pretensioning in the middle, turntable with strong ball bearing slewing ring, wheel chocks with holder, quarter-shell mudguards in front of and behind each axle Low loader lashing eyes over front axle: 2 pairs of ring lashing eyes, 5 tons each at the front on offset Lowbed: 4 pairs of lashing eyes on the side of the low bed, 6 tons each 5 pairs of lashing eyes per 5 tons between the side members Trailer drawbar Turntable Drawbar with tested 40 mm drawbar eye, mechanically adjustable in length by 6 x 100 mm and lockable (drawbar length 1 700 - 2 300 mm) Axles + suspension BPW drum brake axles, each with an axle load of 10 tons, axle adjuster. Axle endurance brake test to 105 km/h, rear axle can be removed manually. By releasing the air lock and lowering the rear to the ground. Then disconnect the connecting hoses from the rear section, insert the transport bar into one of the rear sockets and unhook the rear by gently pushing it down at the rear and pulling it back at the same time (parking brake released). After loading or unloading, drive up to the rear section and hook it in up to the mark. Then lift the rear section up to driving height and attach the connecting hoses. Confirm the pin lock. (Visually check whether the bolt engages) and check the rear function. Air suspension with lift & lower valve Wheels and tires 235 / 75 R 17.5, from leading manufacturers, steel rims in twin arrangement, factory silver Brake system 2-line compressed air brake system, spring-loaded parking brake, 2 interchangeable clutch heads at the front, with connecting lines to the motor vehicle, EBS, electronic brake system with EBS plug at the front, with connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side, 2 white position lights at the front, 2 white/red lane departure lights at the rear, rotating beacon with holder, switched via parking light (light can be removed), 2 pairs of warning signs, double LED illuminated and extendable to 3,300 mm, removable with plug, 2 x 7-pin interchangeable plugs at the front, with connecting cable, 1 x 7-pin agricultural plug, voltage converter 12/24 volt (only for electrics, not for ABS/EBS) Floor Steel/ checker plate floor on offset, between longitudinal and cross member with perforated plate cover. Axle cover cannot be driven over, widening to 3000 or 3300 mm possible. Operating instructions Please note! A special permit is required for axle loads of 10,000 kg. The permit must be applied for individually in each federal state; the legislator does not have to give an approval for 20 tons GG. Customer risk. Cgjdpfoi Ri N Asx Afdsn Special approval required if the overall length of the train exceeds 18 750 mm. Observe country-specific approval regulations. The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. Observe the BO circle!!! Approval / plates Country of registration: Germany, with Dekra approval and expert opinion (according to §13 EG - FGV), prepared for single-line license plate holder, warning sign according to ECE - 70, contour marking with reflective strips according to ECE R 048 Paintwork Front frame hot-dip galvanized incl. passivation, rear frame RAL9006 silver, drawbar KTL bla