Used Fliegl Tps Trailers for sale (346)

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 4,900 kg, maximum load weight: 30,100 kg, overall weight: 35,000 kg, axle configuration: 2 axles, loading space length: 7,200 mm, loading space width: 2,350 mm, loading space height: 1,600 mm, loading space volume: 27 m³, total length: 8,600 mm, total width: 2,550 mm, total height: 3,150 mm, suspension: air, tire size: 385/65 R 22.5, tire condition: 100 %, Customized transport solution Configure your Fliegl vehicle to meet your specific requirements. The vehicle shown is an example. Production and equipment are tailored to individual customer needs. Kdedpfji Ri Niox Afnon Further information Chassis, tipper semi-trailer Fine-grain steel welded construction, in basic lightweight design, turntable with interchangeable 2 kingpin Curved front panel, patented 24 tons, 2-speed landing gear, single-sided operation, with straight lower part, without shock absorption Underrun protection, foldable Partial fender Tow hitch at the rear Axles + suspension SAF disc brake axles with 430 mm disc diameter Axle/suspension laser-aligned to reduce tire wear and fuel consumption Axles in off-road design Air suspension 1. axle, automatic lift axle, including forced lowering and starting aid Hot-dip galvanized lift axle mechanism, 10-year warranty against rust-through Braking system 2-line compressed air braking system, color-coded lines for easy servicing Spring-loaded parking brake 2 fail-safe coupling heads at the front, without connecting line EBS, electronic braking system with EBS socket at the front, without connecting cable Note: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with raise and lower valve Wheels and tires 385/65 R22.5 Steel rims, factory silver "TPMS" tire pressure monitoring system according to ECE R 141, display via the display in the towing vehicle, via EBS, without installation in the truck (this must be available in the truck. Only on base tires) Electrical system 24 volts, multi-chamber lights, yellow LED lighting on the sides Yellow LED lighting on the sides, linked to the turn signal ("flashing side lights") 2 x 7-pole fail-safe sockets at the front, without connecting cable Hydraulics Low-pressure cylinder, max. 170 bar, smallest stage hard-chromed, with HDK screw fitting, fixed part, NW 48 mm (without hose connection) Operation hydraulically via truck auxiliary drive Body Steel round body in Stone Master design made of highly wear-resistant HB 400/450 steel. Sloping front wall with externally mounted hydraulic cylinder with ladder on the front wall. Greenline - conical and aerodynamic body shape Shovel and broom holder externally on the front wall. Membrane - rear wall Rear wall as a swing gate with double-joint hinge, externally supported with double hook locking. 2 clamping screws with cam closures on the lower sides. Side walls continuously 4 mm thick, floor 4/5 mm thick, wear-resistant and weight-optimized design Standing platform with ladder, connection plate for air/electricity and brake with large space for best possible operation. Rollover tarpaulin, single-sided for depositing on the right, with central locking on the left Approval country / signs Germany with Dekra approval and certificate (according to §13 EG - FGV) Body strength according to EN 12642 24/7 service hotline prepared for license plate holder, single row Contour marking with reflective tape according to ECE R 048, white on the sides and red at the rear Paint Frame DB 7350 Novagrau 10-year warranty against rust-through Support legs, black coated Body, RAL color of your choice, single color, subject to availability Rollover tarpaulin, RAL color of your choice, single color Also available with hydraulic rear wall

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 5,600 kg, maximum load weight: 32,400 kg, overall weight: 38,000 kg, axle configuration: 3 axles, loading space height: 1,295 mm, total length: 12,900 mm, total width: 2,550 mm, suspension: air, tire size: 385/65 R22.5", tire condition: 100 %, Customized transport solution Configure your Fliegl vehicle according to your requirements. The vehicle shown is an example. Production and equipment are tailored to individual customer requirements. Chassis, semi-trailer, container Fine-grained steel welded construction, kingpin plate with 2 replaceable kingpins and 2 kingpin positions Front locking on tipping cylinder support with locking on both sides, including tapered wedges Rear locking on continuous pivot shaft with return spring Without subframe for self-supporting containers Kodpfxoi Riv Eo Afnedn Container supports: Locking crossbeam, 2-fold for locking 1 x 30 ft or 1 x 40 ft container. Adjustment via central telescope as an interlocking central tube frame with bolt locking. Optimal kingpin load when transporting 30 ft and 40 ft containers. 24 tons, 2-speed support winch, single-sided operation, with straight lower part, without thrust compensation 2 chock blocks with holder Aluminum side impact protection Galvanized steel underrun protection Half-shell mudguards with anti-splash flaps according to EC Hydraulics 100 low-pressure cylinder max. 150 bar, with HDK screw fitting, fixed part, NW 48 mm. (without hose connection) Actuation hydraulically via truck auxiliary drive, including Hydraulic connection with hose and HDK screw plug NW = 48 mm with knurled nut Axles + suspension SAF disc brake axles with 430 mm disc diameter Axle/chassis laser-aligned to reduce tire wear and fuel consumption Offset axle distance mm (combined transport) up to 44 tons total weight Air suspension Braking system 170 2-line pneumatic braking system Color-coded line routing for easy maintenance. Spring-loaded parking brake Tele Control Axle load adjustment for easy telescoping 2 fail-safe coupling heads at the front, without connecting cable EBS, Electronic Braking System with EBS socket at the front, without connecting cable Note: The trailer may only be towed by tractor units that guarantee the effectiveness of the ABS! with lifting and lowering valve Vehicle - driving stability system Axle load detection via EBS-CAN bus signal, for display on the display in the driver's cab, the truck must be prepared accordingly Wheels and tires 385/65 R22.5, manufacturer's choice Steel rims, factory silver Electrical system 24 Volt, multi-chamber lights, yellow LED lighting on the sides 2 white position lights at the front 2 white/red marker lights at the rear 2 x 7-pole fail-safe sockets at the front, without connecting cable 2 additional LED work lights at the rear, switched via reversing light Customized transport solution Configure your Fliegl vehicle according to your requirements. The vehicle shown is an example. Production and equipment are tailored to individual customer requirements.

Condition: new, machine/vehicle number: Produktpalette, empty load weight: 7,900 kg, maximum load weight: 31,100 kg, overall weight: 39,000 kg, axle configuration: 3 axles, loading space width: 2,330 mm, loading space height: 1,950 mm, loading space volume: 50 m³, total length: 11,200 mm, total width: 2,550 mm, total height: 3,470 mm, suspension: air, tire size: 385/65 R 22,5, Customized transport solution Configure your Fliegl vehicle according to your requirements. The vehicle shown is an example. Production and equipment are tailored to individual customer requirements. More information Chassis, semi-trailer, tipper Fine-grain steel welded construction, lightweight design, with slight curvature, kingpin plate with replaceable 2" kingpin 24 tons, 2-speed landing gear, single-sided operation, with straight lower part, without shock absorption Wheel chocks with holder Underrun protection, foldable Half-shell fenders Integrated fender holder, surface resistant to stone chipping Tarpaulin rod with holder Towing hook at the rear Axles + Suspension BPW disc brake axles with 430 mm disc diameter Axle/chassis laser-aligned, reducing tire wear and fuel consumption Air suspension 1st axle: automatic lift axle, including forced lowering and starting aid Hot-dip galvanized lift axle mechanism, 10-year warranty against rust-through Braking system 2-line compressed air braking system, color-coded lines for easy maintenance Spring-loaded parking brake 2 tamper-proof coupling heads at the front, without connection line EBS, electronic braking system with EBS socket at the front, without connection cable Note: The trailer may only be towed by tractor units that ensure the effectiveness of the ABS! Kjdpfxoi Rizqo Afnodn with lifting and lowering valve Vehicle - Driving stability system Wheels and tires 385/65 R22.5 Steel rims, factory silver "TPMS" tire pressure monitoring system according to ECE R 141, display via display in the tractor unit, via EBS, without truck installation (this must be available in the truck. Only for standard tires). Electrical system 24 volts, multi-chamber lights, yellow LED lighting on the side Yellow LED lighting on the side, linked to the turn signal "Flashing side lights" 2 white position lights at the front 2 white/red side marker lights at the rear 2 x 7-pole tamper-proof sockets at the front, without connection cable Hydraulics Low-pressure cylinder max. 170 bar, smallest stage hard chrome-plated, with HDK screw connection, fixed part, NW 48 mm (without hose connection) Operation hydraulically via truck auxiliary drive Body Steel side body made of high-wear-resistant HB 400 steel, sloping front wall with external hydraulic cylinder mount. Foldable aluminum splash guard on the right for the tarpaulin. Shovel and broom holder on the outside of the front wall. Inside with ladder on the front wall. Side walls continuously 4 mm thick, floor continuously 5 mm thick Membrane - Rear wall Rear wall with 2-wing door division 1/2 to 1/2, with 1 slide in the right wing. With externally mounted torsion bar lock and mechanical locking at the bottom. Standing platform with ladder, connection plate for air/electricity and brake with ample space for best possible operation. Roll cover on one side for depositing on the right, with central locking on the left Country of registration / Signs Germany Type approval according to EC 2007/46 Body strength according to EN 12642 24/7 service hotline prepared for single-row license plate holder Warning sign according to ECE - 70 Contour marking with reflective strips according to ECE R 048, white on the sides and red at the rear Paint Frame DB 7350 Novagrau 10-year warranty against rust-through Support feet, black coated Body, RAL color of your choice, solid color Roll cover, RAL 7035 light gray

Condition: used, overall weight: 38,000 kg, axle configuration: 3 axles, first registration: 06/2021, Equipment: ABS, Fliegl SDS01 BDF interchangeable platform, multi-chassis, lift axle, SAF axles Internal number for inquiries: 0626525 * Permissible total weight: 38,000 kg * Overall condition: very good * First registration: 06/2021 * ABS * 3-axle, air-suspended * SAF axles Kdjdpfxozdl D Hj Afnsn * Disc brakes * Multi-chassis - telescopic extensions Tires: * 1st axle: 385 / 55 R22.5, 40% tread, air-suspended, lift axle * 2nd axle: 385 / 55 R22.5, 40% tread, air-suspended * 3rd axle: 385 / 55 R22.5, 40% tread, air-suspended ----Price: 15,900 EUR + 19% VAT For further questions, you can reach us at the following telephone numbers: We speak: German, English, Polish, French, and…? Typographical errors, errors, and prior sale are subject to change.

Condition: used, Year of construction: 2018, _____Semi-trailer, Fliegl, for external loading only, 3 axles, tire size 365/65R22.5, storage location: customer. Kodezdh R Djpfx Afnsdn

Condition: used, maximum load weight: 35 kg, overall weight: 35,000 kg, loading space volume: 101 m³, tire size: 385/55R22,5, Year of construction: 2025, front tire size: 385/55R22,5, rear tire size: 385/55R22,5, operation weight: 35,000 kg, Tires (front): 385/55R22.5, Tires (rear): 385/55R22.5_____Disc brakes, Air suspension, ABS, EBS3-axle sliding floor semi-trailer, type SDS 390/101 X-tra Long- Total weight permissible / technical: 35000/39000 kg- Payload permissible / technical approx.: 27148/31148 kg- Aggregate load permissible / technical: 24000/27000 kg- Fifth wheel load permissible / technical: 11000/12000 kg- Tare weight (basic version) approx.: 7852 kg +/- manufacturing tolerance- Overall length approx.: 15350mm- Overall width max.: 2550mm- Overall height approx.: 4005mm- Interior length approx.: 14905mm- Interior width approx.: 2470mm- Interior height front approx.: 2655mm- Interior height rear approx.: 2853mm- Volume approx.: 101 cbm- Fifth wheel height approx.: 1130mm- Kingpin installation dimension approx.: 1640mm- Front corner dimension approx.: 2040mmChassis / Fifth Wheel:- Fine-grained steel welded construction in lightweight design, up to the support legs- Fifth wheel plate with replaceable 2" kingpin- X-tra Long with approx. 14905 mm interior length- 24 ton, 2-speed support winch, single-sided operation, with straight lower part, without push-pull compensation- Extension ladder at the rear- Door lock on the side- 2 wheel chocks with holder- Aluminum side impact protection- Steel underrun protection with wide Fliegl mudguards- Folding mudflap for lighting unit- Quarter panel fenders- Rear impact protection- Aluminum ladder approx. 3550 mm, with holder on the side- Tarp pole with holder- 1 plastic toolbox, lockableAxles + Suspension:- BPW disc brake axles with 430 mm disc diameter- Air suspension- 1st axle automatic lift axle (circle driving with lifted 1st axle is not supported)Brake system:- 2-line pneumatic brake system- Color-coded line routing for easy servicing- 24 Volt EBS, electronic brake system with EBS socket at the front- with raise and lower valve- Vehicle - driving stability system- AAC Basic, automatic load relief axle acting on the last axle, as maneuvering aid, up to 20 km/h, can be switched off manually- Axle load detection via EBS-Canbus signal, for display on the display in the driver's cab, truck must be equipped accordinglyWheels and tires:- 385/55 R22.5- Steel rims, factory silverElectrical system:- 24 Volt, multi-chamber lights, yellow LED lighting on the sides- LED work lights on both sides- Additional LED work lights at the rearSB Hydraulics:- Hydraulic cylinder with sliding mechanism installed in the floor. 2-circuit hydraulics- Switching between forward/reverse operation is done electrically via radio remote control- Sliding floor power supply via parking lights- Recommended pump output:Flow rate: 110 ltr/minPressure: 250 barOil tank filling min: 100 ltrFloor:- Sliding floor with wear plate at the rear made of V2A sheet steel- Floor boards made of aluminum, 8 mm floor profile, ribbed design- End caps in aluminumBody:- Aluminum box body made of high-quality, abrasion-resistant material. Front and side walls made of aluminum hollow profiles, rounded at the top. Kjdszdgzzopfx Afnodn

Condition: used, axle configuration: 3 axles, first registration: 05/2021, loading space length: 7,150 mm, loading space width: 2,460 mm, loading space height: 1,750 mm, suspension: air, tire size: 385/65r22.5, wheelbase: 1,310 mm, Year of construction: 2021, Tyre size: 385/65r22.5 Ksdpovxqu Rjfx Afnsdn Suspension: air suspension Drive: Wheel GVW: 39.000 kg Tipper: Back

Condition: used, axle configuration: 2 axles, first registration: 05/2019, total length: 5,000 mm, total width: 2,500 mm, suspension: air, Year of construction: 2019, Additional information : Brand: FLIEGL Model: TDS180 Structure: dolly Year: 05.2019 Suspension: air Kjdpfx Aswl Dlhjfnedn Brakes: drum Dimensions: L/W: 5000 mm / 2500 mm Masses: full/empty: 18000 kg / 2500 kg Suspension type : air Brakes : Disc Suspension type : air Brakes : Disc Model year : 2019 = More information = Suspension: air suspension Empty weight: 2.500 kg Carrying capacity: 15.500 kg GVW: 18.000 kg Please contact Andrei Somov, Mark Ševtšenko, Alejandro Goyeneche, Deniss Urmaker or Hesham Haddad for more information

Condition: used, axle configuration: 2 axles, first registration: 06/2003, total length: 5,400 mm, total width: 2,480 mm, suspension: air, Year of construction: 2003, Additional information : Brand: FLIEGL Model: TDS180 Structure: dolly Year: 06.2003 Suspension: air Brakes: drum Dimensions: L/W: 5400 mm / 2480 mm Kdodpfx Aownwtwefnon Masses: full/empty: 16000 kg / 2710 kg Model year : 2003 Suspension type : air Brakes : Disc Suspension type : air Brakes : Disc = More information = Suspension: air suspension Empty weight: 2.710 kg Carrying capacity: 13.290 kg GVW: 16.000 kg Please contact Andrei Somov, Mark Ševtšenko, Alejandro Goyeneche, Deniss Urmaker or Hesham Haddad for more information

Condition: used, axle configuration: > 3 axles, first registration: 09/2008, total length: 17,700 mm, total width: 2,600 mm, suspension: air, Year of construction: 2008, Additional information : Brand: FLIEGL Model: SVS580T Structure: platform ( platform L=13211 mm / W=2540 mm / H=930 mm ) Year: 09.2008 Suspension: air Brakes: drum Dimensions: L/W: 17700 mm / 2550 mm Masses: full/empty: 58000 kg / 14310 kg Model year : 2008 Suspension type : air Brakes : Drum Liftable axle : Liftable axle Suspension type : air Brakes : Drum Suspension type : air Brakes : Drum Steering : Steering Suspension type : air Brakes : Drum Steering : Steering = More information = Ksdpfx Aowkdmvjfnjdn Suspension: air suspension Front axle: Lift axle Middle axle 1: Steering Rear axle: Steering Empty weight: 14.310 kg Carrying capacity: 43.690 kg GVW: 58.000 kg Please contact Andrei Somov, Mark Ševtšenko, Alejandro Goyeneche, Deniss Urmaker or Hesham Haddad for more information

Condition: new, maximum load weight: 23,920 kg, overall weight: 30,000 kg, axle configuration: 3 axles, NEW VEHICLE Fliegl 3 axle low loader type DTS 300, hot-dip galvanized Total weight 24,000 kg / 30,000 kg Payload 17,920 kg / 23,920 kg Empty weight 6,080 kg Ksdpfxexb Nmyo Afnsdn Total length 10,900 mm Loading length 8,680 mm Loading bed 6,500 mm including 900 mm approach slope Parabolic suspension Long ramps 2,800 mm with hydraulic operation Wider widths to 3,000 mm with warning signs and rotating beacon Large lashing package with 5.0 and 10.0 ton lashing points 5 pairs of stake pockets Towing eye 40 mm Plus pre-freight / provision from the Wiesmoor storage location 1,280.00 €/ Net Rent-to-own offer: term 48 months, residual value 40%, down payment only VAT. Monthly rate: EUR 500.00

Condition: new, maximum load weight: 17,900 kg, overall weight: 24,000 kg, axle configuration: 3 axles, loading space length: 8,670 mm, loading space width: 2,500 mm, loading space height: 860 mm, total width: 2,520 mm, From ongoing production Total weight: 24,000kg/ 30,000kg Empty weight: 6,100kg Payload: 17,900kg/ 23,900kg Total length: 10,890mm Loading length: 8,670mm total, 2,520mm offset, 6,500mm loading bed Width: 2,520mm Loading height: 860mm Further information Steel welded construction Turntable with strong ball bearing ring Foldable rear support Wheel chocks with holder Aluminum side impact protection Rear mud flaps across the entire width (not in conjunction with forklift bracket) Half-shell mudguard 1st axle with anti-spray mud flaps Anti-spray mud flaps behind 2nd and 3rd axles Plastic tool box Extendable extensions to 3,000mm Storage compartment for wooden planks in the middle of the loading area Wooden planks 70 mm for widening to 3,000 mm Lashing eyes for low loader 1 pair of lashing cutouts in the longitudinal beam at the front on the offset, 10 tons each. 4 pairs of lashing holes in the outer frame of the crank, each with 5 tons (tension belt attachment) 7 pairs of lashing mushrooms embedded in the outer frame at the top and side, each with 10 tons 1 x at the front on the crank, 6 x in the low bed Pair of ring lashing eyes embedded in the outer frame, each with 5 tons (can be converted to stake pockets) Pair of additional folding lashing eyes, each with 10 tons Kjdpfsuytx Sjx Afnodn 1 x on the crank 1 x embedded in the floor behind the last axle Trailer towing device, turntable Draw fork with tested 40 mm drawbar eye Draw fork height adjustment via spring Axles + suspension Drum brake axles, at the manufacturer's discretion "Axles/chassis laser-measured" Reduction in tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation (rocker compensation) Wheels and tires 235 / 75 R 17.5" at the manufacturer's choice steel rims in twin arrangement, factory silver brake system 2-line compressed air brake system spring-loaded parking brake 2 interchangeable coupling heads at the front, with connecting lines to the motor vehicle, 24 volt ABS and ALB, with ABS plug at the front, with connecting cable electrics 24 volt, multi-chamber lights, yellow LED lighting on the side 2 white position lights at the front 2 white/red lane keeping lights at the rear 2 x 7-pin interchangeable plugs at the front, with connecting cable, LED rotating beacon with holder, switched via parking light (light removable) pair of warning signs with double LED lighting and extendable to 3,000mm floor front bend with steel/checker plate covering storage box embedded in the crossing slope to the bend then with approx. 70mm softwood floor, in the wheel arch area steel/checker plate covering rear bevel with 70mm softwood floor Low loading area including rear bevel 6,500mm Loading ramps Steel ramps 2,800mm long, 750mm wide, can be moved sideways Additional ramp lock foldable at the bottom (to prevent the ramps from slipping sideways, not in conjunction with lateral hydraulic ramp shifting) Covered with wood (tip area with steel/checker plate) Hydraulic via tractor auxiliary drive with throttle, actuation on the side in FR left Hydraulic connection with SVK plug NW 10/3, including connecting hose Paintwork Frame hot-dip galvanized including passivation Loading ramps hot-dip galvanized Plus pre-freight / provision from storage location 26639 Wiesmoor 1,280.00 €/ net

Condition: new, maximum load weight: 29,500 kg, overall weight: 35,000 kg, axle configuration: 3 axles, loading space length: 7,200 mm, loading space width: 2,350 mm, loading space height: 1,450 mm, loading space volume: 25 m³, total width: 2,550 mm, Vehicle is from ongoing production – available in approx. 2 weeks Vehicle / Body: Tipper body Gross weight: 35,000kg / 39,000kg Tare weight: 5,500kg!!! Payload: 29,500kg / 33,500kg Overall length: 8,600mm Volume: 25 cbm Further Information: - Overall height approx. 3,160mm - Internal width approx. 2,350mm - Fifth wheel height approx. 1,200mm Chassis Semi-Trailer Tipper: - Fine-grain steel welded construction, in basic lightweight design - 1x central landing gear leg - Retractable underrun protection - Underrun protection with “spring assist” for easier operation - Half-shell mudguards - Integrated "mudguard bracket" with stone-repellent surface - With anti-spray mudflaps only on the last axle - 2 towing hooks at the rear Axles & Suspension: - SAF disc brake axles with 430 mm disc diameter - "Axle/chassis laser alignment" for reduced tire wear and lower fuel consumption - Axles in off-road specification - Air suspension - Air bag pressure gauge, mounted at the front on curved chassis - 1st axle with automatic lift axle, additionally controllable electrically from the truck, including forced lowering and start-up aid, no truck installation required (Start-up aid function up to 30% axle overload and up to a speed of max. 25 km/h) Braking System: - 2-line compressed air braking system Color-coded line routing for easier service. - Spring-loaded parking brake - 2 foolproof coupling heads at the front, without connecting line - 24 Volt EBS, electronic braking system with EBS socket at the front, without connecting cable - With lift & lower valve - Vehicle stability control system Ksdpfsvhyf Rox Afnsdn - Automatic tipping lowering with shut-off valve Wheels and Tyres: - 6 x 385/65 R22.5” European brand, manufacturer’s choice Electrics: - 24 Volt, multi-chamber LED lights, side yellow LED lighting, LED license plate lighting (Note: Some towing vehicles may display fault codes despite full functionality) - Side yellow LED lighting linked to indicator "flashing side marker lights" - Premium LED side marker lights, each with 20 LEDs per light - 2 white front position lights, LED included - 2 white/red lane position lights at the rear, LED included - 2 x 7-pin and 1 x 15-pin foolproof sockets at the front, without connecting cable - LED work lights both sides (switched via reversing light) - 2 additional LED work lights, recessed at rear Hydraulics: - High-pressure cylinder max. 250 bar, smallest stage hard chrome-plated, with HDK screw coupling, fixed section, NW 48 mm - Manufacturer Hyva - Operation hydraulic via truck PTO - Hydraulic connection with hose and vehicle screw connector NW = 54 mm with large wing nut Body: HARDOX steel round tipper body in "Stone Master Design" made of highly wear-resistant HB 400/450 steel. Sloped front wall with external hydraulic cylinder mount. Interior with access at front wall. - Greenline – conical and aerodynamic body design - External shovel and broom holder at front wall - "Membrane" rear wall - Rear wall as pendulum tailgate with "double joint hinge", external, with dual hook locking. 2 clamping screws with toggle locks at lower side - Rear wall with rubber seal Note: Heat resistant up to max. 170°C! - Side walls continuously 4 mm thick, floor 4/5 mm thick, wear and weight-optimized construction - Fliegl S.T.E.P. – swiveling standing platform at the front with foldable access ladder for side entry front left

Condition: new, maximum load weight: 18,400 kg, overall weight: 24,000 kg, axle configuration: 3 axles, loading space length: 5,900 mm, loading space width: 2,500 mm, loading space height: 860 mm, total width: 2,520 mm, Gross vehicle weight: 24,000 kg / 30,000 kg Unladen weight: 5,600 kg Payload: 18,400 / 24,400 kg Total length: 10,290 mm Loading length: 5,900 mm including rear slope Width: 2,520 mm Loading height: 860 mm Further information Plus pre-freight / Delivery from storage location 26639 Wiesmoor €1,280.00 / net Kdjdpfowlmr Dox Afnen Low-loader trailer chassis Steel welded construction Turntable with sturdy ball-bearing slewing ring Foldable rear support Wheel chocks with holder Rear mud flaps across the entire width 1 plastic toolbox Prepared for extensions to 3,000 mm (holes in the outer frame with cover, not in the rear slope) Low-loader lashing eyes 1 pair Lashing cutouts in the front longitudinal member, 10 tons each. 7 pairs of lashing pins, 10 tons each, embedded in the outer frame at the top and sides. 1 x at the front, 10 tons each. 5 x in the lowbed. 1 x in the rear slope. 12 pairs of lashing holes in the outer frame, 5 tons each. (Tire strap attachment) 5 x offset, 6 x drop-bed, and 1 x in the rear slope Trailer turntable drawbar Drawbar with tested 40 mm drawbar eye Drawbar height adjustment via spring Axles + Suspension Drum brake axles, at the manufacturer's discretion "Laser-measured axle/chassis" reduces tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation (Rocker compensation) Wheels and Tires 235/75 R 17.5" at the manufacturer's discretion Twin-axle steel rims, factory silver Brake System Two-line pneumatic brake system Spring-loaded parking brake Two interchangeable coupling heads at the front, with connecting lines to the towing vehicle Connecting lines extended by approximately 60 cm Without ABS, but with mechanical ALB then max. 60 km/h approval Electrics 12-volt, multi-chamber lights, without yellow LED side lighting, side reflectors 2 white position lights at the front 2 white/red lane departure lights at the rear 1 x 7-pin 12-volt connector at the front, with connecting cable, extended by approximately 60 cm 1 LED rotating beacon with bracket, switched via parking light (light removable) 2 pairs of warning signs with double LED illumination and extendable to 3,000 mm Floor Front offset with steel/checker plate flooring Storage box recessed into the ramp to the offset then with 70 mm softwood flooring, steel/checker plate flooring in the wheel arch area Rear slope with 70 mm softwood flooring Low-bed area including rear slope 5,900 mm Load-up ramps Steel ramps 2,800 mm long, 750 mm wide, laterally movable covered with wood (Tip section with steel/checker plate) Hydraulic via tractor PTO with throttle, actuated on the side in FR left-hand drive Hydraulic connection with SVK connector NW 10/3, including connecting hose Operating Instructions For 10,000 kg axle load, an exemption is required; only indivisible loads are possible!!! The stated gross weight is technically possible; depending on the load, the gross weight may not be achieved while complying with the permissible axle/support and fifth wheel loads. (Poor handling and caster behavior due to incorrect load distribution is possible) Country of Registration/Signs Country of Registration: Germany with DEKRA approval and certificate, for max. 60 km/h approval, towing vehicle LoF, (Country of Registration Switzerland: max. 40 km/h possible) prepared for two-line license plate holder without contour markings/reflective stripes according to ECE R 048 Frame paint finish: RAL 7021 Black-gray "10-year warranty a

Condition: used, maximum load weight: 33,787 kg, overall weight: 39,000 kg, axle configuration: 3 axles, first registration: 07/2017, next inspection (TÜV): 01/2027, loading space length: 7,200 mm, loading space width: 2,350 mm, total width: 2,550 mm, Gross weight: 39,000 kg / 35,000 kg Tare weight: 5,213 kg Payload: 33,787 kg / 29,787 kg Overall length: 8,200 mm Loading length: 7,200 mm Width: loading width 2,350 mm / total 2,550 mm Additional information - Internal bin height: 1,450 mm - Volume: 24.5 m³ - Fifth wheel height: 1,200 mm - Tarpaulin bar with bracket Kedpfsycbi Rex Afnsdn - BPW axles - Air suspension - Steel round-body in "tub shape" - Rear wall as pendulum tailgate - Work platform with access steps - One-sided roll tarp Vehicle may be wrapped or labeled with advertising.

Condition: new, maximum load weight: 30,010 kg, overall weight: 40,000 kg, axle configuration: > 3 axles, loading space length: 10,000 mm, loading space width: 2,520 mm, loading space height: 900 mm, total width: 2,550 mm, Brand-new Fliegl 4-axle low-bed trailer with wheel recesses and split ramps, type VTS 400 RM Hire-purchase offer: 48-month term, down payment only the VAT, final residual value 40% Monthly rate: EUR 899.00 Vehicle / Body: Low-bed trailer First registration: New vehicle Gross weight: 24,000kg/40,000kg Unladen weight: 9,990kg Payload: 14,010kg / 30,010kg Overall length: 12,000mm Loading length: total approx. 10,000mm, gooseneck approx. 2,850mm, load bed including rear taper approx. 7,150mm Width: 2,550mm Loading height: 900mm Kdedpfxstrizkj Afnon Further information Chassis: Low-bed trailer Steel welded construction Turntable with heavy-duty ball race Foldable rear support Wheel chocks with holders Aluminum side underrun protection Full-width rear spray flap Half-shell mudguards 1st and 2nd axle with anti-spray mud flaps behind each axle, anti-spray mud flap behind the 4th axle Excavator arm trough above rear axles, from the rear axle to the rear approx. 1,800mm long, approx. 650mm wide and 150mm deep 2 pairs of lashing holes, each 5t, in the excavator arm trough, on the longitudinal frame approx. 300mm from the front and approx. 200mm before the rear taper Spare wheel bracket for 1 spare wheel, upright on the gooseneck, front center, spare wheel brand same as main equipment, steel rim Toolbox let into the floor on the gooseneck with lid, W=720mm / L=520mm / D=170mm 1st pair of wheel recesses after the gooseneck, let into the deep deck in the driving lane, chamfered for access, length at the bottom approx. 1,600mm, approx. 400mm deep. Note! Frame in the main beam area 400mm higher than the wheel recess. 2nd pair of wheel recesses between the axles, let into the deep deck in the driving lane, chamfered for access, length at the bottom approx. 600mm, approx. 300mm deep. Note! Frame in the main beam area 300mm higher than the wheel recess. Extensions retractable to 3,000mm (no extension at the rear taper and not in the wheel recesses below) (track width of machines or vehicles to be transported must not exceed the outer frame width of 2,550mm) Storage compartment for timber planks underneath the low-bed deck 70mm timber planks for extension to 3,000mm Lashing points – low-bed trailer 1 pair of RIN lashing rings inlaid at the front on the gooseneck, each 5t 4 pairs of lashing holes in the outer frame, each 5t (for securing strap attachments) 8 pairs of lashing mushrooms flush-mounted top and side in the outer frame, each 10t 2 at the front on the gooseneck 6 in the deep deck First lashing ring 250mm from the front, last a maximum of 250mm from the rear, spacing between lashing rings not more than 1,100mm 5 pairs of stake pockets inlaid in the outer frame, inner dimensions 70 x 40mm (convertible to 5t ring lashing eyes, not included) 1 pair of foldable lashing rings additionally inlaid in the floor, each 10t 1 inside next to main frame at start of low-bed section 2 pairs of additional foldable lashing rings, each 10t 1 on the gooseneck (protrudes) 1 behind the last axle inlaid in the floor Towing device for turntable trailer Drawbar with certified 50mm towing eye, towing eye inclined by 8° D-value at least 160kN Axles and Suspension BPW drum braked axles "Axles/chassis laser aligned" – reduces tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bushings and mechanical front axle load equalization (rocker equalizer) Wheels and Tires 235 / 75 R 17.5" Manufacturer’s choice, with M + S marking Steel rims in twin arrangement,

Condition: new, maximum load weight: 31,920 kg, overall weight: 40,000 kg, axle configuration: > 3 axles, loading space length: 10,410 mm, loading space width: 2,500 mm, loading space height: 900 mm, total width: 2,550 mm, New vehicle Fliegl 4 axle low loader trailer with ramps, type VTS 400 Total weight: 24,000kg/40,000kg Empty weight: 8,080kg Payload: 15,920kg/31,920kg Total length: 11,940mm Loading length: total approx. 10,410mm, offset approx. 2,490mm, loading bed including rear bevel approx. 7,920mm Width: 2,550mm Loading height: 900mm Further information plus pre-freight / provision from storage location 26639 Wiesmoor 1,280.00 ¤/ net Rent-purchase offer: term 48 months, down payment only VAT, residual value 40% monthly rate EUR 759.00 Chassis Low-loader trailer Steel welded construction Turntable with strong ball bearing ring Foldable rear support 2 wheel chocks with holder Aluminum side impact protection Rear splash flaps across the entire width Half-shell mudguards 1st + 2nd axle with anti-spray splash flaps behind each axle, Anti-spray splash flaps in front of and behind 3rd and 4th axle Excavator arm recess over the rear axles starting at the rear, approx. 1800 mm long, approx. 650 mm wide and approx. 150 mm deep, 2 pairs of lashing holes, each 5 tons. in the excavator arm recess on the side of the longitudinal frame approx. 300 mm from the front and approx. 200 mm in front of the rear bevel 1 plastic tool box, w=600 / h=425 / d=460 mm, lockable Storage box embedded in the floor on a crank with lid, W=720 mm/ L=520 mm / D= 170 mm Extensions extendable to 3,000 mm (not in the rear bevel) (The track width of the construction machines or vehicles to be transported must not exceed the outer frame width 2,550 mm) Storage compartment for wooden planks below the low-loading area Wooden planks 70 mm for widening to 3,000 mm Lashing eyes for low-loader 1 pair of lashing cutouts embedded in the longitudinal beam at the front on a crank, 10 tons each. Kodpfevv D Ixox Afnsdn 4 pairs of lashing holes in the outer frame, each with 5 tons (tension belt attachment) 9 pairs of lashing mushrooms, each 10 tons, embedded in the outer frame at the top and side 2 x at the front on the bend 7 x in the low bed First lashing eye 250 mm from the front and last max. 250 mm from the back, distance between the lashing eyes not greater than 1100 mm 3 additional pairs of folding lashing eyes, each 10 tons 1 x on the bend (sticks out) 1 x at the beginning of the low bed, embedded inside on the longitudinal beams 1 x embedded in the floor behind the last axle Towbar with tested 50 mm towing eye Towbar height adjustment via spring Axles + suspension Drum brake axles, as selected by the manufacturer "Laser-measured axles/chassis" Reduction in tire wear and fuel consumption Air suspension with raising & lowering valve + Auto-reset function Wheels and tires 235 / 75 R 17.5" at the manufacturer's choice Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-loaded parking brake Axle load detection via EBS-Canbus signal, for display on display in the driver's cab, truck must be prepared accordingly, no truck installed (no calibrated scales) Vehicle - driving stability system 2 interchangeable coupling heads at the front, with connecting cables to the motor vehicle, 12-24 volt EBS, electronic braking system with EBS plug at the front, with connecting cable Knorr brand Caution: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrics 12-24 volts, multi-chamber LED lights, yellow LED lighting on the side, license plate lighting in LED, (Note! Incorrect diagnoses can occur with certain towing vehicles, although the function is p

Condition: new, maximum load weight: 23,890 kg, overall weight: 30,000 kg, axle configuration: 3 axles, Vehicle from ongoing production NEW VEHICLE Fliegl 3 axle low loader type DTS 300, hot-dip galvanized Kdedjk N Adkopfx Afnjn Total weight 24,000 kg / 30,000 kg Payload 17,890 kg / 23,890 kg Empty weight 6,080 kg Total length 10,900 mm Loading length 8,680 mm Loading bed 6,500 mm including 900 mm approach slope Loading height 860 mm Air suspension with lifting and lowering valve Long ramps 2,800 mm with hydraulic actuation Wider extensions to 3,000 mm with warning signs and rotating beacon Large lashing package with 5.0 and 10.0 ton lashing points 5 pairs of stake pockets Towing eye 40 mm Plus pre-freight / provision from Storage space Wiesmoor 1,280.00 ¤/ net Rent-purchase offer: term 48 months, residual value 40%, down payment only VAT monthly rate: EUR 609.00

Condition: used, maximum load weight: 8,470 kg, overall weight: 11,800 kg, axle configuration: 2 axles, first registration: 06/2018, loading space length: 5,000 mm, loading space width: 2,420 mm, loading space height: 900 mm, total width: 2,550 mm, Gross weight: 11,800 kg Unladen weight: 3,330 kg Payload: 8,470 kg Overall length: 6,950 mm Loading length: 5,000 mm Width: 2,550 mm / loading width approx. 2,420 mm Loading height: approx. 950 mm Further information: - Front support leg - Rear support, foldable - 450 mm drop sides - Large lashing package - Frame hot-dip galvanized incl. passivation Kdodpfx Afey Arkasnsn - Loading ramps optional: €1,280.00

Condition: new, maximum load weight: 8,780 kg, overall weight: 11,800 kg, axle configuration: 2 axles, loading space length: 5,000 mm, loading space width: 2,420 mm, loading space height: 950 mm, total width: 2,550 mm, Further information plus pre-carriage / provision from storage location 26639 Wiesmoor €1,280.00 net Chassis Central Axle Tipping Trailer Steel welded construction, continuous tipping shaft at the rear with 80 mm spherical tipping bearing Support leg with gear at the front Foldable rear support 2 wheel chocks with holders Steel underrun protection Full-width rear mudflaps Quarter-shell fenders 1 plastic toolbox, w=600 / h=425 / d=460 mm, lockable Note! Sidewall touches the toolbox when folded down. Lockable storage space for loading ramps beneath the loading area WITHOUT ramps Drawbar for central axle trailer Drawbar with certified 40 mm towing eye Drawbar height adjustable via spindle, max. adjustment range 300 mm Axles & Suspension BPW drum brake axles "Chassis/undercarriage laser-aligned" to reduce tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bushings and mechanical axle load equalization (rocker compensation) Wheels and Tyres 235 / 75 R 17.5" manufacturer’s choice Steel rims, factory silver Brake System 2-line air brake system Color-coded line routing for easy service Hand spindle parking brake Integral air tank ABS and ALB, with ABS connector at the front and connection cable Caution: The trailer may only be towed by vehicles that ensure the effectiveness of the ABS! 2 non-interchangeable coupling heads at the front, with connection lines to the truck Electrics 24 Volt, multi-chamber lighting, side yellow LED marker lights 2 white position lights at the front 2 white/red lane lights at the rear 2 x 7-pin non-interchangeable plugs at the front, with connection cable Hydraulics Three-way tipping system, hydraulic multi-piston cylinder with lift limiter and safety cable Low-pressure cylinder up to max. 170 bar, without flow restrictor. If required, needs to be retrofitted on the truck. Hydraulic connection with SVK plug NW 10/3, incl. connecting hose Operated hydraulically via truck PTO Tipping Platform Robust tipping platform with 4 mm steel floor, steel sidewall construction, continuous, fold-down sidewalls Non-swing mounted without central locking underneath. Plug-in corner posts at the rear. Rear wall fold-down and swing-mounted, central locking underneath. Platform length approx. 5,000 mm, sidewalls with 6 hinges at the bottom Sidewall retracting springs (not possible with split sidewalls) Platform width 2,420 mm 5 pairs of lashing rings in the floor, each rated to 5 tons Operating Notes The specified gross weight is technically possible; depending on the load, the gross weight may not be achievable while observing permissible axle/support/kingpin loads. (Poor driving and trailing performance possible due to incorrect load distribution) Approval/Country Country of registration: Germany with Dekra inspection and certificate (in accordance with §13 EC-FGV) 24/7 service hotline Prepared for single-line number plate holder Contour marking with reflective tape according to ECE R 048, white on sides and red at the rear Paintwork Frame hot-dip galvanized including passivation Kodpfxoy Dzlce Afnjdn "15-year guarantee against rust-through" Sidewalls/platform RAL 5002 ultramarine blue Note! Platform inside is only primed unless otherwise painted bridge design! Optional loading ramps €1,280.00 net

Condition: new, maximum load weight: 8,000 kg, overall weight: 10,500 kg, axle configuration: 2 axles, loading space length: 5,500 mm, loading space width: 2,050 mm, loading space height: 630 mm, total width: 2,550 mm, Vehicle / Body: Tandem Low-Bed Trailer First Registration: New vehicle Gross Vehicle Weight: 10,500 kg Unladen Weight: 2,500 kg Payload: 8,000 kg Overall Length: 7,280 mm Loading Length: Platform length approx. 5,500 mm Width: Platform width 2,050 mm / 2,550 mm Loading Height: Platform height 630 mm Additional Information plus freight/preparation from stock location 26639 Wiesmoor €1,280.00 / net - Overall height approx.: 2,900 mm - Side wall height approx.: 400 mm - Frame RAL 5001 Blue Green Chassis: Central axle low-bed trailer Fine-grain steel welded construction Telescopic support leg at the front Telescopic rear support Wheel chocks with holder Steel fenders over both wheels Drawgear for central axle trailer Drawbar with certified 40 mm towing eye Drawbar height-adjustable via spindle, max. adjustment range 250 mm Axles + Suspension Euro axles at our discretion, with tapered roller bearings and S-cam brakes "Axle/chassis laser alignment" reduces tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bushings and mechanical axle load equalization (rocker compensation) Wheels and Tires 235/75 R 17.5" manufacturer's choice Steel rims, factory silver Braking system 2-line compressed air brake system Spring-actuated parking brake 2 fail-safe coupling heads at the front, with connection lines to tractor unit, ABS and ALB, with ABS connector at the front, with connection cable Attention: The trailer may only be towed by vehicles that ensure the effectiveness of the ABS! Electrics 24 Volt, multi-chamber lamps, side yellow LED lighting 2 white position lights at the front 2 white/red lane marker lights at the rear 2 x 7-pin fail-safe connectors at the front, with connecting cable, TTS Platform low-mounted steel trough, platform floor with steel/chequer plate covering, steel sides solidly welded to the floor Braking system 2-line compressed air brake system Spring-actuated parking brake 2 fail-safe coupling heads at the front, with connection lines to tractor unit, 24 Volt ABS and ALB, with ABS connector at the front, with connection cable Attention: The trailer may only be towed by vehicles that ensure the effectiveness of the ABS! Electrics 24 Volt, multi-chamber LED lamps, side yellow LED lighting, license plate lighting in LED, (Note: with certain tractor units, incorrect diagnostics may occur even though the functions are in operation) 2 white position lights at the front in LED 2 white/red lane marker lights at the rear in LED 2 x 7-pin fail-safe connectors at the front, with connecting cable, park sockets for electrics / ABS / air connections on the drawbar TTS Platform low-mounted steel trough, platform floor with steel/chequer plate covering, steel sides solidly welded to the floor Platform length 5,500 mm Trough at front and sides with "Load-Lock Profile" for lashing straps (8 in front, 16 per side) Note: Minor unevenness in the floor due to welding distortion possible! 2 pairs of lashing eyes, 1 x in the front corners of the steel trough and 1 x in the floor rear, each 5t Kodpfx Aewwab Aefnsdn 3 pairs of additional lashing eyes in the floor, each 5t 4 pairs of lashing eyes bolted onto the side walls Ramps Steel ramps, 2,300 mm long, 510 mm wide, laterally adjustable with handgrip on the ramps Ramp surface with "Mega Grip" made of serrated grating (contact area with steel/chequer plate) with gas pressure springs for one-man operation

Condition: new, maximum load weight: 17,900 kg, overall weight: 24,000 kg, axle configuration: 3 axles, loading space length: 8,670 mm, loading space width: 2,500 mm, loading space height: 860 mm, total width: 2,520 mm, New vehicle Fliegl 3 axle low loader trailer with ramps, type DTS 300 Vehicle completely hot-dip galvanized Total weight: 24,000kg/30,000kg Empty weight: 6,100kg Payload: 17,900/23,900kg Total length: 10,890mm Loading length: 8,670mm total, 6,500mm low bed including rear bevel / 2,170mm offset Width: 2,520mm Loading height: 860mm Further information plus pre-freight / provision from storage location 26639 Wiesmoor 1,280.00 ¤/ net Rent-purchase offer: term 48 months, down payment only VAT, residual value 40% monthly rate: EUR 569.00 Steel Welded construction Pivot bolster with strong ball bearing ring Foldable rear support Wheel chocks with holder Aluminum side impact protection Splash flaps at the rear over the entire width (not in conjunction with forklift bracket) Half-shell mudguard on 1st axle with anti-spray splash flaps Anti-spray splash flaps behind 2nd and 3rd axles 1 plastic tool box, w=600 / h=425 / d=460 mm, lockable Extensions extendable to 3,000 mm (not in the rear bevel) (The track width of the construction machines or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Storage compartment for wooden planks in the middle of the loading area 70 mm wooden planks for widening to 3,000 mm Lashing eyes for low loader 1 pair of lashing cutouts in the longitudinal beam at the front on a bend, 10 tonnes each. 4 pairs of lashing holes in the outer frame of the crank, each with 5 tons (tension belt attachment) 7 pairs of lashing mushrooms, set into the outer frame at the top and side, each with 10 tons 1 x at the front on the crank 6 x in the low bed First lashing eye 250 mm from the front and last max. 250 mm from the back, distance between the lashing eyes not greater than 1100 mm Ksdpsv D T R Esfx Afnodn 5 pairs of ring lashing eyes set into the outer frame, each with 5 tons (can be converted to stake pockets) 2 additional pairs of folding lashing eyes, each with 10 tons 1 x on the crank (protrudes) 1 x set into the ground behind the last axle Towbar with tested 40 mm towbar Towbar height adjustment via spring Axles + suspension Drum brake axles, as selected by the manufacturer "Laser-measured axle/chassis" Reduction in tire wear and tear Fuel consumption Air suspension with raising and lowering valve Wheels and tires 235 / 75 R 17.5" at the manufacturer's discretion Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-loaded parking brake Vehicle driving stability system Axle load detection via EBS-Canbus signal, for display on display in the driver's cab, truck must be prepared accordingly, no truck installed (no calibrated scales) 2 interchangeable coupling heads at the front, with connecting cables to the motor vehicle, 24 volt EBS, electronic braking system with EBS plug at the front, with connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrics 24 volts, multi-chamber lights, yellow LED lighting on the side 2 white position lights at the front 2 white/red lane keeping lights at the rear 2 x 7-pin, interchangeable plugs at the front, with connecting cable, 1 LED rotating beacon with holder, switched via parking light (light removable) 2 pairs of warning signs with double LED lighting and extendable to 3,000 mm Floor Front bend with steel/checker plate covering Storage box embedded in the crossing slope to the bend then with approx. 70 mm softwood floor, steel/checker plate covering in the wheel arch area Rear bev

Condition: new, maximum load weight: 15,080 kg, overall weight: 21,000 kg, axle configuration: 1 axle, NEW VEHICLE Fliegl 1 axle special low loader Total weight 21,000 kg Payload 15,080 kg Empty weight 5,920 kg Total length 13,630 mm Loading length 9,940 mm Low bed from the wheel area tapering to 210 mm loading height Hanging bar for aluminum ramps at the rear of the vehicle across the entire width Towing eye at the rear Electric cable winch pulling force 8,165 kg with radio remote control, cable length 35 meters Kdjdpfx Afellwitjnsn 1 pair of wheel recesses approx. 700 mm after the gooseneck in the floor 2 pairs of wheel stops pluggable, 4 pairs of plug-in positions Large lashing package Axle BPW drum brake Air suspension with lifting and lowering valve Lighting completely in LED 1 pair of aluminum ramps load capacity 12,000 kg, storage compartment in the middle of the loading area Frame hot-dip galvanized, outer frame painted red plus pre-freight / provision from the Wiesmoor storage location 1,280.00 ¤/ net New vehicle without first registration with full manufacturer's warranty Vehicle is available immediately Rent-to-own offer: term 48 months, residual value 40%, down payment only VAT monthly rate EUR 899.00 (other terms are possible)

Condition: new, maximum load weight: 25,050 kg, overall weight: 35,000 kg, axle configuration: 3 axles, loading space length: 13,500 mm, loading space width: 2,500 mm, loading space height: 950 mm, total width: 2,550 mm, Total weight: 35,000 kg / 48,000 kg Unladen weight: 9,950 kg Payload: 25,050 kg / 38,050 kg Overall length: 21,000 mm Loading length: loading area approx. 13,500 mm / max. loading length 21,000 mm Width: 2,550 mm Loading height: 950 mm Additional information: Brand-new vehicle from ongoing production, available from approx. week 8/2026 Telescopic rear support 4 wheel chocks with holders 4 pairs of recessed container locks in the floor, suitable for 1x 40 ft. container or 2x 20 ft. containers 1 spare wheel holder for 1 spare wheel, with wheel fastening kit, basket design 11 pairs of stake pockets recessed in the outer frame, suitable for FR plug-in stakes 80x50 mm, installed flush with the outer frame, with opening for lashing strap or chain hooks 20 plug-in stakes, W=80 mm / D=50 mm / L=1500 mm 1 plastic toolbox 3 pairs of lashing eyes, each rated at 3.5 t, fitted to the side frame - in the gooseneck area 13 pairs of foldable lashing rings, each rated at 10,000 daN, suspended freely swiveling along the side frame profile (also suitable for wide-load securing) 1 pair of foldable lashing rings, each rated at 10,000 daN, installed laterally in the intermediate support Air suspension with raise and lower function Kjdpfoumha Nex Afnsdn 1st axle: automatic lift axle, additionally with forced lowering including starting aid with operator button on the semi-trailer, no cab operation with lift & lower valve + auto reset function Wheels and tires: 235 / 75 R 17.5" Steel rims, twin arrangement, factory silver 24 volt, multi-chamber lights, lateral yellow LED lighting 2 white LED position lights at the front 2 white/red lane marker lights at the rear, LED 2 x 7-pin and 1 x 15-pin confusion-proof sockets at the front, without connecting cable 2 additional LED work lights at the rear, switched via reversing light 1 removable rotating beacon on the underrun protection 1 x 7-pin socket at the rear 6 lateral sockets, 2x front wall, 2x landing legs, 2x rear end (left + right) 7-pin 2 work lamps recessed at the top in the front wall incl. switch 2 pairs of oversize boards, each with 2 LED marker lights per board, extendable sideways up to 3,500 mm, boards can also be attached to the loading area (width adjustment infinitely variable) Fixed steel front wall, 1,200 mm high, with robust steel corner posts without corner bevel, straight lateral design. 2 lashing holes at the top, inside and outside, in the front wall corners Front frame hot-dip galvanized + visible area of outer frame, finish painted in RAL 3002 Carmine Red Rear frame hot-dip galvanized + visible area of outer frame, finish painted in RAL 3002 Carmine Red Front wall RAL 3002 Carmine Red

Condition: new, maximum load weight: 23,340 kg, overall weight: 30,000 kg, axle configuration: 3 axles, NEW VEHICLE Fliegl 3 axle platform low loader DTL - S - 300 Agrar, frame and chassis hot-dip galvanized Total weight: 24,000 kg / 30,000 kg Payload: 17,340 kg / 23,340 kg Empty weight: 6,660 kg Total length: 11,625 mm Platform length: 9,000 mm including 900 mm approach slope Loading height: 900 mm Large lashing package Draw fork 40 mm Kjdpsllwhnefx Afnedn Tires 235 / 75 R 17.5" twin Without ABS, max. 60 km/h approval Electrical system 12 volt, LED rotating beacon Ramps with spring lift, ramp length 2,800 mm Vehicle from ongoing production - approx. 14 days in advance. Plus Pre-freight / provision from the Wiesmoor storage facility 1,280.00 ¤/ net Towing vehicle LoF, agricultural or forestry registration Rent-purchase offer: term 48 months, residual value 40%, down payment only VAT monthly rate: 599.00