Used Fliegl Lowbed Semitrailers for sale (347)

Condition: new, machine/vehicle number: Produktpalette, empty load weight: 6 kg, maximum load weight: 28 kg, overall weight: 35 kg, axle configuration: 3 axles, loading space length: 15,030 mm, loading space width: 2,480 mm, loading space height: 4,060 mm, total length: 15,150 mm, total width: 2,550 mm, total height: 4,060 mm, suspension: air, tire size: 435/50R19,5, tire condition: 100 %, Additional information Chassis, semi-trailer, transport company Fine-grained steel welded construction, with preload for slight tension in the neck area, kingpin plate with interchangeable 2 kingpins X-tra Long, with an internal length of 15030 mm Outer frame slightly angled, new design with Load-Lock profile for attaching lashing straps 24-ton, 2-speed landing gear, single-side operation, with straight lower part, without thrust compensation Note: Free support foot angle or free swivel radius to the rear approx. 1930 mm Retractable ladder at the rear Door lock on the side 2 chocks with holder Aluminum side impact protection Galvanized steel under-ride protection Hjdpfx Aei Riwuefwop Partial wheel arches in front of the 1st axle and behind each axle Rear impact protection Axles + Suspension SAF disc brake axles Axle/chassis laser-aligned to reduce tire wear and fuel consumption Air suspension Braking system 2-line compressed air braking system Color-coded lines for easy servicing Spring brake parking brake 2 non-interchangeable coupling heads at the front, without connecting line EBS, electronic braking system with EBS socket at the front, without connecting cable Caution: The semi-trailer may only be pulled by towing vehicles that guarantee the effectiveness of the ABS! with lifting and lowering valve Vehicle driving stability system AAC Basic, automatic lift axle acting on the last axle, as an aid for maneuvering, up to 20 km/h, can be manually switched off Axle load detection via EBS-Canbus signal, for display on the driver's cab, truck must be appropriately prepared, no truck installation (no calibrated scale) Wheels & Tires 435/50R19.5, manufacturer's choice Steel rims, factory silver Electrical system 24 Volt, multi-chamber lights, yellow LED lighting on the side Yellow LED lighting on the side coupled with the turn signal, flashing Side marker lights 2 white position lights at the front 2 white/red side marker lights at the rear 2 x 7-pole non-interchangeable sockets at the front, without connecting cable Floor Sieved plywood, approx. 30 mm thick, on longitudinal supports for high point load capacity for forklift axle load up to max. 7100 kg Front wall / Corner posts at the front 2580 mm high, corner posts steel in full volume design, release mechanism for side tarpaulin on the front wall, crash blocker, at the bottom inside at approx. 140 mm height with steel impact protection Center posts 3 pairs of sliding posts that can be moved along the entire length, with 4-fold insert pockets & at the bottom with a long pocket. 3 pairs of post positions Insert slats 5 rows of wooden slats Rear wall / Corner posts at the rear Corner posts at the rear steel up to the lower edge of the roof, attachment for tarpaulin with round tube and tarpaulin tensioning ratchet Rear portal doors, 2-wing with 2 internal swivel latch locks each Tarpaulin Tarpaulin, with welded-in horizontal and vertical straps Tensioning closures made of stainless steel Roof Sliding roof, rear end lift that can be folded up, with roof that can be slid from back to front, L-roof beam for the automotive industry, interior width between the roof beams approx. 2490 mm, tarpaulin color: white Roof non-elastic, hardly any deflection of the roof beam during loading and unloading EcoLift - liftable roof by approx. 380 mm, on both sides, with gas spring support, 3 driving positions at the front: Interior height at the front set to approx. 3000 mm Optimal rain gutter at the rear, at the top of the end ra

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 3,200 kg, maximum load weight: 35,800 kg, overall weight: 39,000 kg, axle configuration: 3 axles, tire size: 385/65 r22.5, Customized transport solution Configure your Fliegl vehicle according to your requirements. The vehicle shown is an example. Production and equipment are customized to meet individual customer needs. More information Fine-grained steel welded construction in lightweight design, fifth wheel plate with 2 replaceable kingpins, only 2 longitudinal beams as double T-beams for subsequent front drawbar coupling in new/current design, outer frame slightly angled with Load-Lock profile for securing lashing straps. Note: to attach the straps in conjunction with the sideboards, the sideboards must be opened!, 24 tons, 2-speed landing gear, single-sided operation, with straight lower part, without push-pull compensation, shims with holder, aluminum side impact protection, foldable, steel under-run protection, galvanized, extendable, half-shell mudguards!!Supplied loose, not mounted!!, with anti-splash flaps behind each axle, 1 plastic water tank, capacity approx. 30 liters, on the left side in the front Hodpji Riwqofx Afwsp BPW disc brake axles with 430 mm disc diameter, axle/suspension laser-aligned to reduce tire wear and fuel consumption, air suspension, 1st axle automatic lift axle, additionally manually lowerable, operable with a hand knob on the vehicle 2-line pneumatic brake system, with 1 central standard air reservoir, spring brake parking brake, 2 tamper-proof coupling heads at the front, without connecting line, EBS, electronic braking system with EBS socket at the front, without connecting cable, EBS 2S/2M, test connection for brake cylinder pressure on the EBS module routed to the outside, attention: the trailer may only be towed by towing vehicles which ensure the effectiveness of the ABS!, with lifting and lowering valve, control unit + brake integrated into the frame as in a semi-trailer tipper, mounted in front of the axles Brake pad wear indicator on disc brakes via ABS/EBS indicator light on the truck 385/65 R22.5, Continental brand, steel rims, factory silver 24 Volt, multi-chamber lights, yellow LED lighting on the side as in a semi-trailer tipper, dimension 3000 mm must be observed, 2 white position lights at the front in LED, loose, 2 white/red outline lights at the rear, 2 x 7-pole tamper-proof sockets at the front, without connecting cable Germany, type approval according to EC 2007/46 for the complete vehicle, 24/7 service hotline, prepared for a double license plate holder in a single row: 1 x plastic and 1 x stainless steel interchangeable holder Warning sign according to ECE - 70, aluminum, loose, EBS, safe parking, without contour marking / reflective strip according to ECE R 048, Frame: DB 7350 Novagrau, landing gear: black coated Immediately available! Customized transport solution Configure your Fliegl vehicle according to your requirements. The vehicle shown is an example. Production and equipment are customized to meet individual customer needs.

Condition: used, empty load weight: 5,300 kg, overall weight: 38,000 kg, axle configuration: 3 axles, first registration: 09/2018, total length: 2,550 mm, total height: 13,100 mm, suspension: air, tire size: 385/65R22,5, | Fliegl 30-foot tipping chassis | BPW axles | Lift axle | Alloy wheels | Top condition | Austrian vehicle Hsdpfx Asyp Hd Hjfwjp

Condition: used, axle configuration: 3 axles, first registration: 03/2011, total length: 12,100 mm, total width: 2,550 mm, total height: 1,300 mm, suspension: air, tire size: 385/55R22,5, wheelbase: 9,250 mm, color: other, Year of construction: 2011, = Additional Options and Accessories = - EBS Hodpfxjy U U R Hj Afwop = Notes = Number of axles: 3, Payload: 36,200 kg, Tare weight: 5,800 kg, Gross vehicle weight: 42,000 kg, Chassis type: Full chassis, Kingpin size: 2 inch, Suspension type: Air suspension, EBS, 2X 20, 1X 30, 1X 40 FT HIGHCUBE // DISC BRAKES // LIFT AXLE = Further Information = General Information Cab: Day cab Registration number: OL-43-HP Drivetrain Fuel type: Diesel Transmission Gearbox: Manual transmission Axle Configuration Brakes: Disc brakes Suspension: Air suspension Axle 1: Tire size: 385/55R22.5; Lift axle; Tire tread depth left: 5 mm; Tire tread depth right: 10 mm Axle 2: Tire size: 385/55R22.5; Tire tread depth left: 8 mm; Tire tread depth right: 10 mm Axle 3: Tire size: 385/65R22.5; Tire tread depth left: 2 mm; Tire tread depth right: 2 mm Weights Unladen weight: 5,800 kg Payload: 36,200 kg GVW: 42,000 kg Environment Emission class: Euro 0 Condition Overall condition: very poor Technical condition: very poor Optical condition: very poor Damage: none = Company Information = Kleyn Trucks is one of the world's largest independent used vehicle dealerships. Here you can choose from a constantly changing stock of 1,200 used trucks, tractor units, and trailers. Our range includes all European brands from various years of manufacture and price ranges. Why buy from Kleyn Trucks? Simple! • Large, rapidly changing stock • Recognizable quality • A good price • Correct business practices • We speak many languages • We understand our customers • Support with import and transport • (Export) registration can be arranged quickly • Expert technical services • The security of "recognizable quality" • And more.... Please visit our website for special offers and a complete inventory: Leasing through Kleyn Trucks is possible in most European countries! Quickly calculate your leasing rate and submit an inquiry through our website. Inquire directly about our European warranty package.

Condition: used, axle configuration: 3 axles, first registration: 05/2023, loading space length: 13,700 mm, loading space width: 2,400 mm, loading space height: 3,000 mm, total length: 13,900 mm, total width: 2,600 mm, total height: 4,000 mm, suspension: air, tire size: 435/50R19,5, wheelbase: 8,970 mm, color: other, Year of construction: 2023, Equipment: ABS, = Additional Options and Accessories = - EBS = Notes = Number of axles: 3, Payload: 32920 kg, Tare weight: 6080 kg, Gross vehicle weight: 39000 kg, Chassis type: Full chassis, Kingpin size: 2 inch, Suspension type: Air suspension, ABS, EBS, Body construction year: 2023, Sunroof, Axle type: SAF = Further Information = General Information Cab: Day cab License plate: OX-71-GS Drivetrain Fuel type: Diesel Transmission Gearbox: Manual gearbox Axle Configuration Tire size: 435/50R19.5 Brakes: Disc brakes Suspension: Air suspension Axle 1: Lift axle; Tire tread depth left: 9 mm; Tire tread depth right: 9 mm Axle 2: Tire tread depth left: 10 mm; Tire tread depth right: 10 mm Axle 3: Tire tread depth left: 8 mm; Tire tread depth right: 7 mm Weights Tare weight: 6,080 kg Payload: 32,920 kg GVW: 39,000 kg Functional Sunroof: Yes Hodey U Ut Uepfx Afwjp Environment Emission class: Euro 0 Maintenance APK (Periodic Vehicle Inspection): valid until 11.2026 Condition Overall condition: average Technical condition: average Optical condition: average Damage: none Financial Information Leasing price: €334 per month (default, 60 months); Please inquire for further information and conditions = Company Information = Kleyn Trucks is one of the largest independent used vehicle dealerships in the world. Here you can choose from a constantly changing stock of 1200 used trucks, tractor units, and trailers. Our range includes all European brands from various years of manufacture and price ranges. Why buy from Kleyn Trucks? It's simple! • Large and rapidly changing stock • Recognizable quality • A good price • Proper business practices • We speak many languages • We understand our customers • Assistance with import and transport • (Export) registration can be arranged quickly • Expert technical services • The security of "recognizable quality" • And more.... Please visit our website for special offers and a complete inventory: Leasing through Kleyn Trucks is possible in most European countries! Quickly calculate your leasing rate and submit an inquiry via our website. Inquire directly about our European warranty package.

Condition: used, axle configuration: 3 axles, first registration: 06/2021, loading space length: 13,700 mm, loading space width: 2,400 mm, loading space height: 3,000 mm, total length: 13,900 mm, total width: 2,600 mm, total height: 4,000 mm, suspension: air, tire size: 435/50R19,5, color: other, Year of construction: 2021, Equipment: ABS, = Additional Options and Accessories = - EBS = Notes = Number of axles: 3, Tare weight: 6060 kg, Gross vehicle weight: 39000 kg, Chassis type: Complete chassis, Chassis material: Steel, Kingpin size: 2 inch, Suspension type: Air suspension, ABS, EBS, Body construction year: 2021, Side wall material: Tarpaulin, Sliding roof, Axle type: SAF = Additional Information = General Information Cabin: Day cab Registration number: KLEYN1 Drivetrain Fuel type: Diesel Transmission Gearbox: Manual gearbox Axle Configuration Tire size: 435/50R19.5 Brakes: Disc brakes Suspension: Air suspension Axle 1: Tire tread depth left: 5 mm; Tire tread depth right: 6 mm Axle 2: Tire tread depth left: 12 mm; Tire tread depth right: 8 mm Axle 3: Tire tread depth left: 5 mm; Tire tread depth right: 5 mm Weights Unladen weight: 6,060 kg Hodpfey U Utzjx Afwsp Payload: 32,940 kg GVW: 39,000 kg Functional Sliding roof: Yes Environment Emission class: Euro 0 Condition Overall condition: average Technical condition: average Optical condition: average Damage: none Financial Information Leasing price: 315 € per month (default, 60 months); Ask for more information and conditions = Company Information = Kleyn Trucks is one of the world's largest independent dealers in used vehicles. Here you can choose from a constantly changing stock of 1200 used trucks, tractor units, and trailers. Our range includes all European brands across different years of manufacture and price ranges. Why buy from Kleyn Trucks? Simple! • Large, rapidly changing stock • Recognizable quality • A good price • Correct business practices • We speak many languages • We understand our customers • Support with import and transport • (Export) registration is quickly arranged • Expert technical services • The security of "recognizable quality" • And more.... Please visit our website for special offers and a complete inventory: Leasing through Kleyn Trucks is possible in most European countries! Quickly calculate your leasing rate and send an inquiry via our website. Ask directly about our European warranty package.

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 6,350 kg, maximum load weight: 28,650 kg, overall weight: 35,000 kg, axle configuration: 3 axles, tire size: 435/50 r19,5, tire condition: 100 %, Additional Information Chassis, Semi-trailer, Transport Company Fine-grained steel welded construction, kingpin plate with 2 replaceable kingpins Attachment rail for aluminum ramps across the entire width Reinforced frame for vehicle loading Outer frame with Load-Lock profile approximately every 400 mm for securing lashing straps 10 pairs of lashing eyes recessed in the outer frame, each rated at 10 tons 24-ton, 2-speed support winch, single-sided operation, with semi-circular lower part and straight connecting plate, with extension compensation Foldable rear support 2 chock blocks with holder Aluminum side underrun protection Galvanized steel underrun protection Quarter panel fenders in front of the 1st axle and behind each axle with anti-spray flaps behind each axle Pair of ferry eyes, yellow marked 1 spare wheel holder for 1 spare wheel, with wheel fastening kit 2 plastic toolboxes, with drawer and insert, w=650 / h=520 / d=670 mm, lockable with a padlock (lock not included) Container locking system, 4 pairs of locks recessed in the floor for 2 x 20 ft or 1 x 40 ft containers Hedpfx Afjld Ihlswop 10 pairs of lashing pockets recessed in the outer frame, internal dimensions 70 x 40 mm 10 lashing pockets recessed in the center of the floor, internal dimensions 70 x 40 mm 2 lashing/lashing bar rails recessed transversely in the floor across the entire width up to the outer frame (max. usable internal width between the outer lashing bars approx. 2170 mm), approx. 100 mm high. With 20 mm round steel rails, top and bottom, distance from top to bottom approx. 60 mm (of the round steel). Bottom with an angle plate as a closure, open halfway downwards. For lashing and inserting lashing bars 80 x 80: Position 2 and 4 according to Fliegl data sheet 20 lashing bars, hot-dip galvanized Note: The lashing pockets / insertion pockets are not designed for the sole securing of long materials, pipes, etc. without wrapping. Storage space for aluminum access ramps, ramps can be slid in from the rear 3 pairs of folding eyes, 10 tons, in the outer frame (1x in front of the front wall and 2x in the rear area). Axles + Suspension SAF disc brake axles Axle / chassis laser-measured, reduces tire wear and fuel consumption Air suspension 1st axle automatic lift axle, including forced lowering and start-up assistance, actuated by 3x brake (start-up assistance is functional up to an axle load exceeding 30% and up to a speed of max. 25 km/h) Axle lift below the recommended ride height, therefore no guarantee for tire damage 2 ride heights, adjustable via hand knob, 1 x for saddle height 980 mm, 1 x for saddle height 1100 mm (Note! Vehicle with tilt) Braking System 2-line pneumatic braking system Color-coded line routing for easy servicing Spring-loaded parking brake 2 non-interchangeable coupling heads at the front, without connecting line EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The semi-trailer may only be pulled by towing vehicles that guarantee the effectiveness of the ABS! with lifting and lowering valve 2 ride heights, adjustable via hand knob, 1 x for saddle height 980 mm, 1 x for saddle height 1100 mm (Note! Observe overall height, exceeding height is at the customer's risk) Ride height in connection with lift axle, with the lift axle raised, the loading or overall height increases by 50 mm (with Mega Flex only at the lower ride height or saddle height) Vehicle - Driving stability system Wheels and tires 435/50 R19.5, manuf

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 5 kg, maximum load weight: 29 kg, overall weight: 35 kg, axle configuration: 3 axles, total length: 13,990 mm, total width: 2,550 mm, tire size: 385 / 65 r 22,5, tire condition: 100 %, Customized transport solution Configure your Fliegl vehicle according to your requirements. The vehicle shown is an example. Production and equipment are tailored to individual customer needs. Further information Chassis, semi-trailer, forwarding company Steel welded construction in reinforced design, only 2 longitudinal beams as double T-beams with steel/diamond plate between the longitudinal beams, kingpin plate with 2 interchangeable kingpins. Mudguard for taillights. 1 steel storage box, recessed between longitudinal beams 8 pairs of lashing eyes screwed or welded to the frame, as per manufacturer's choice 24 tons, 2-speed support winch, single-sided operation, with straight lower part, without thrust compensation 2 support wedges with holder Aluminum side underrun protection Galvanized steel rear underrun protection Semi-shell mudguards with anti-splash flaps according to EG 1 spare wheel holder for 1 spare wheel, with wheel fastening kit 8 pieces of timber rack brackets, as per manufacturer's choice, screwed to the frame with 2 extendable timber racks each, from 1800 to 2800 mm, 7 tons per pair Axles + Suspension SAF disc brake axles with 430 mm disc diameter Air suspension with lifting and lowering valve, safety cable on the axles 1st axle automatic lift axle, including forced lowering and starting assist, activated by 3x braking (starting assist is functional up to an axle load exceeding 30% and up to a speed of max. 25 km/h) Offset axle spacing mm (combined transport) up to 44 tons total weight Wheels and tires 385 / 65 R 22.5 as per manufacturer's choice Steel rims, factory silver Braking system 2-line pneumatic braking system Spring-loaded parking brake Axle load detection via EBS-Canbus signal, for display on the screen in the driver's cab, the truck must be correspondingly pre-equipped, no truck installation (no calibrated scale) 2 non-interchangeable coupling heads at the front, without connection cable EBS, electronic braking system with EBS socket at the front, without connection cable Note: The trailer may only be pulled by towing vehicles that guarantee the effectiveness of ABS! Electrical system 24 volts, multi-chamber lights, yellow LED lighting on the sides 2 white position lights at the front 2 white/red marker lights at the rear 2 x 7-pole and 1 x 15-pole non-interchangeable sockets at the front, without connection cable Front panel/corner posts at the front Steel/lattice front panel, approx. 2,300 mm high, screwed to the frame Approval / Signs Country of approval: Germany Type approval according to EG 2007/46 prepared for single-row license plate holder Contour marking with reflective tape according to ECE R 048, white on the sides and red at the rear Paint Frame DB 7350 Novagrau Support feet black coated Hsdpfx Afsi Rivwewop Front panel hot-dip galvanized Note: Archive images! Customized transport solution Configure your Fliegl vehicle according to your requirements. The vehicle shown is an example. Production and equipment are tailored to individual customer needs.

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 5,000 kg, maximum load weight: 23,000 kg, overall weight: 28,000 kg, axle configuration: 2 axles, loading space height: 900 mm, total length: 13,800 mm, total width: 2,550 mm, total height: 2,638 mm, suspension: air, tire size: 235/75 r17,5, tire condition: 100 %, Customized transport solution Configure your Fliegl vehicle according to your requirements. The vehicle shown is an example. Production and equipment are customized according to customer requirements. More information Chassis, semi-trailer, transport company Fine-grained steel welded construction, kingpin plate with 2 replaceable kingpins Outer frame slightly inclined, new design with Load-Lock profile for attaching lashing straps 24 tons, 2-speed landing gear, single-sided operation, with straight lower part, without push-pull compensation Free support foot angle or free swivel radius to the rear, approx. 1920 mm 2 chocks with holder Aluminum side underrun protection Steel rear underrun protection Quarter panel fenders in front of and behind each axle 1 spare wheel holder for 1 spare wheel, with wheel fastening kit 1 plastic toolbox, with insert, w=620/h=360/d=440 mm, lockable with a padlock. (Lock not included) Axles + Suspension Drum brake axles, selection according to manufacturer Laser-measured axle/chassis alignment, reduces tire wear and fuel consumption Air suspension Braking system 2-line compressed air braking system, color-coded lines for easy servicing Spring brake parking brake Duomatic connection at the front, without connecting line EBS, electronic braking system with EBS socket at the front, without connecting cable Note: The trailer may only be towed by towing vehicles that ensure the effectiveness of the ABS! with lifting and lowering valve Vehicle - driving stability system Wheels and tires 235/75 R17.5, manufacturer's choice Steel rims, factory silver Electrical system 24 volt, multi-chamber lights, yellow LED lighting on the sides 2 white position lights at the front 2 white/red marker lights at the rear 1 x 15-pin socket at the front, without connecting cable Floor Sieve-printed panels, approx. 30 mm thick, for high point load capacity, for forklift axle load up to max. 5,600 kg Front wall / corner posts 25 mm aluminum hollow profile, approx. 1,350 mm high, corner posts made of steel in a volumetric design Country of approval / plates Germany with Dekra inspection and certificate (according to §13 EG - FGV) 24/7 service hotline Hodpfskv Uvzox Afwop prepared for single-line license plate holder Contour marking with reflective strips according to ECE R 048, white on the sides and red at the rear Paintwork Frame hot-dip galvanized including passivation, 15 years warranty against rust Front wall aluminum Note: These are archive images! Customized transport solution Configure your Fliegl vehicle according to your requirements. The vehicle shown is an example. Production and equipment are customized according to customer requirements.

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 6,860 kg, maximum load weight: 28,140 kg, overall weight: 35,000 kg, axle configuration: 3 axles, suspension: air, tire size: 235/75 17,5, tire condition: 100 %, Additional information Chassis Fine-grained steel welded construction, kingpin plate with 2 replaceable kingpins Recessed rail for loading ramps on the rear extension over the entire width, outer edge beveled to prevent damage. Reinforced frame for vehicle loading Outer frame with load-lock profile approx. every 400 mm for securing lashing straps 10 pairs of lashing eyes recessed on the top/outside of the outer frame, each 10 tons, starting after the neck area 24-ton, 2-speed support jacks, single-sided operation, with a flat mounting plate 2 wheel chocks with holder Aluminum side impact protection Galvanized steel underride protection Sheet metal as a splash guard riveted to the bottom, in the neck area above the center of the bogie axle and above the axle assembly Semi-elliptical fenders with anti-spray flaps according to EC Container locking system, 4 pairs of locking recesses recessed in the floor for 2 x 20 ft or 1 x 40 ft containers, 4 pairs of container locking adapters (additional cross supports required at the front and rear of the container; the container must rest evenly across its width in conjunction with the locks; cross supports are not included) Attention! Damage to the platform floor is possible due to the cross supports! Rear extension, mechanical, with hand crank, extendable by approx. 1500 mm, lockable every 500 mm, including extendable underride protection with lighting (then the rear ladder is omitted) Covered with platform in the wheel arch area, with steel diamond plate in the center. Attention! Ramp loading at the rear is only possible with the rear extension in the retracted position! Storage space for loading ramps integrated in the rear extension, only usable when the rear extension is extended 1000 mm – then there is an overhang For transporting the ramps with the rear extension retracted, there is storage space for the ramps on the right side of the frame in front of the axles 1 pair of ramps, 3000 mm long, 300 mm wide, load capacity per pair 6000 kg (recessed rail for ramps on the rear extension) Rear slope to approx. 500 mm Electric winch, 24 volts, pulling force approx. 8165 kg, mounted in the center at the front, operated with a wireless remote control, cable length 35 m x approx. 10 mm, with a cable guide and removable guide rollers Hsdpfx Afelf Dtmswep Axles + Suspension Drum brake axles Axle/suspension laser-aligned to reduce tire wear and fuel consumption Air suspension 1st axle automatic lift axle, including forced lowering and start-up assistance, activated by 3x braking (start-up assistance functions up to an axle load exceedance of 30% and a speed of max. 25 km/h) with central lift arm Axle lift below the recommended ride height, therefore no guarantee for tire damage Braking system 2-line pneumatic braking system Color-coded lines for easy service. Spring parking brake 2 non-interchangeable coupling heads at the front, without connecting line EBS, Electronic Braking System with EBS socket at the front, without connecting cable Attention: The trailer may only be pulled by towing vehicles which guarantee the effectiveness of the ABS! with raise and lower valve Vehicle - driving stability system Wheels and tires 235/75 17.5, manufacturer's choice Steel rims in twin arrangement, factory silver Electrical system 24 volts, multi-chamber lights, yellow LED lighting on the side 2 white position lights at the front in LED 2 white/red marker lights at the rear 2 additional LED work lights at the rear, switched via the revers

Condition: used, empty load weight: 5,100 kg, maximum load weight: 32,900 kg, overall weight: 38,000 kg, axle configuration: 3 axles, first registration: 07/2024, next inspection (TÜV): 09/2026, total length: 9,500 mm, total width: 2,550 mm, suspension: air, tire size: 385/55 R 22,5, tire condition: 50 %, Year of construction: 2024, Equipment: ABS, Galvanized chassis, BPW disc brakes, 1st axle liftable, ADR, spare wheel holder, container carrier extendable centrally via tractor and mechanically at the rear, twist locks for all types of containers. Hodpfx Afex Nh Hqewsp

Condition: new, empty load weight: 6,600 kg, maximum load weight: 17,400 kg, overall weight: 24,000 kg, axle configuration: 3 axles, loading space length: 6,500 mm, total length: 10,900 mm, suspension: steel, tire size: 235/75 R17,5 (Doppelbereifung), color: silver, gearing type: mechanical, fuel consumption (urban): 1,090 l/100km, Empty weight: 6600kg, permissible total weight: 24000kg, loading space length: 6,500 mmTire size: 235/75 R17.5, 1st axle: , 2nd axle: , 3rd axle: , leaf spring suspension, 3 axle low loader trailer with offset DTS-S 300 - bogie with strong ball bearing ring - foldable rear support - 1 spare wheel holder for 1 electric bike, with wheel fastening kit - 1 spare wheel, same make as basic tires, steel rim - 1 plastic tool box - extensions extendable to 3000mm (not in rear bevel) - storage compartment for wooden planks in the middle of the low load area - wooden planks 70mm for extension to 3000mm Lashing eyes low loader: - with spring jack Support axles + suspension: - SAF - drum brake axles - Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation (rocker compensation) Brake system: - 2-line compressed air brake system - Spring-loaded parking brake Electrics: - 24 volt, multi-chamber lights, yellow LED lighting on the side - 1 LED rotating beacon with holder, switched via parking light (light removable) - 2 pairs of warning signs with double LED lighting and extendable to 3000 mm Floor: - Storage box embedded in the crossing slope to the crank - then with 70 mm softwood floor, steel / checker plate covering in the wheel arch area - Rear bevel with 70 mm softwood floor Loading ramps: Steel ramps 2,800 mm long, 750 mm wide, laterally movable, covered with wood - - 1 pair of ring lashing eyes embedded on the crank at the front, 10 tonnes - 4 pairs of lashing holes in the AR with 5 tonnes each for tensioning belt attachment - 7 pairs Lashing eyes at the top and sides of the outer frame, 10 tonnes each - 1 x at the front on the crank, 6 x in the low bed - 5 pairs of stake pockets in the outer frame, inside 70x40 mm (can be converted to 5 tonne ring lashing eyes for an additional charge) - 2 pairs of additional folding lashing eyes, 10 tonnes each, 1x at the front on the crank, 1x behind the 3rd axle, axles + suspension: - SAF - drum brake axles - parabolic suspension with maintenance-free steel-rubber bearings and mechanical Ac Hjdpfxotcwkre Afwop

Condition: new, axle configuration: 3 axles, color: grey-black, gearing type: mechanical, Colour natural, lifting axle, electronic braking system EBS, connection plug 1x15-pin, equipment outer frame slightly slanted, new version with "Load-Lock profile" for attaching tensioning belts, 13 pairs of lashing eyes additionally in the outer frame, each 5 to 24 tonnes. 2-speed support winch, one-sided operation, with semi-circular lower section and straight forklift ram protection made of steel on the outer frame on the side. and rear 1 spare wheel holder for 1 electric bike, with wheel fastening kit 1 plastic tool box 650mmx520mmx670mm 7 pairs of stake pockets embedded in the outer frame, 83 x 83 mm SAF disc brake axles with 430 mm air suspension 1st axle automatic lift axle, including forced lowering and starting aid, actuation of 3x brakes Wheels and tires 6 385/65 R22.5" Make 6 steel rims, factory silver Floor screen-printed panels approx. 30 mm thick, cross joints with omega insert, for high point load capacity for forklift axle load up to max. 7 100 kg Front wall / corner stanchions front 25 mm aluminum hollow profile, 1 950 mm high, corner stanchions steel in volume design + 2 center supports "crash blocker", bottom inside at approx. 140 mm height Side walls 25 mm aluminum hollow profile, 700 mm high Paintwork frame hot-dip galvanized including passivation "15 year guarantee against rust through" side walls ALU anodized, errors and changes reserved. Hsdpfetcwmiex Afwjp

Condition: new, functionality: fully functional, overall weight: 16,000 kg, maximum load weight: 13,700 kg, empty load weight: 2,300 kg, loading space width: 2,480 mm, loading space length: 7,750 mm, loading space height: 3,000 mm, machine/vehicle number: Produktpalette, Customized Transport Solution Configure your Fliegl vehicle to meet your specific requirements. The vehicle shown is an example. Production and equipment are customized according to customer specifications. Tandem Trailer Chassis Welded steel construction with a floor assembly approximately 152 mm high; load-bearing and torsionally rigid steel frame construction. Longitudinal beam floor construction with a load-resistant outer frame and guide tunnels spaced 600 mm apart; tunnels feature guides on top and sides, tunnel height approx. 45 mm; 4 x swap body corner fittings based on a 20-foot standard. 4 side-extending/folding parking feet with dual locking mechanism for a parking height of 970 mm, with support leg rest Side door stops Rear impact protection made of flat bar Pallet stops on both sides, approx. 20 mm high with perforated profile for securing straps; loading height is reduced by approx. 20 mm Floor Screen-printed panels approx. 27 mm thick, for high point load capacity, for forklift axle load up to max. 4,400 kg Front wall/corner stanchions Approx. 2,580 mm high, remainder covered with tarp; steel corner stanchions in full-size design; release mechanism for side tarp on front wall Inner front wall additionally lined with a 1,250 mm high screen-printed panel Center stanchions 1 pair of sliding stanchions adjustable along the entire length, with 4-compartment pockets and a long pocket at the bottom. 1 pair of stanchion positions Hsdpfxskt Ni Us Afwep Slotting Slats 5 rows of wooden V-shaped slotting slats Rear wall/rear corner stanchions Rear steel corner stanchions extending to the bottom edge of the roof, tarpaulin attachment with round tube and tarpaulin tensioning ratchet Rear portal doors, double-leaf, each with 2 internal twist-lock latches Tarpaulin Tarpaulin, with welded-in horizontal and vertical straps, reinforcements for stanchions Stainless steel tensioning fasteners Roof Sliding roof, rear end lift folds up, roof can be slid from rear to front, L-shaped roof rail for the automotive industry, interior width between roof rails approx. 2,490 mm, tarpaulin color: white EcoLift – lifting roof by approx. 380 mm, liftable on both sides, with gas spring assistance, Registration / Plates Country of registration: Germany Fliegl manufacturer’s certificate for body strength in accordance with EN 12642 XL, Fliegl manufacturer’s certificate for body strength in accordance with DL 9.5, pallet stops on both sides, approx. 20 mm high, loading height reduced by approx. 20 mm Fliegl manufacturer’s certificate for load securing in accordance with VDI 2700, Sheet 12 ff. Pallet stops on both sides, approx. 20 mm high; loading height is reduced by approx. 20 mm Paint Finish Frame Hot-dip galvanized, including passivation Front corner posts Hot-dip galvanized Front wall Aluminum Rear corner posts Hot-dip galvanized Rear wall White

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 11,000 kg, maximum load weight: 27,000 kg, overall weight: 38,000 kg, axle configuration: 3 axles, loading space length: 9,500 mm, loading space width: 2,480 mm, loading space height: 3,040 mm, total length: 13,800 mm, total width: 2,550 mm, total height: 4,020 mm, suspension: air, tire size: 235 / 75 r 17,5, tire condition: 100 %, Custom-made transport solution Configure your Fliegl vehicle according to your requirements. The vehicle shown is an example. Production and equipment are customized according to customer requirements. Chassis Steel welded construction with narrow crossmember spacing and reinforced design, low-loader outer frame profile, for transporting construction machinery up to 32,000 kg and with a maximum outer width of the construction machinery of 2550 mm, kingpin plate with replaceable 2 kingpins. Rear slope of approx. 1200 mm and 7°. Ramp shaft closed at the top with steel/diamond plate, in the low-bed, omega rail laterally at the bottom on the outer frame as a mounting rail for tarpaulin and spacers for lashing points, not in the wheel area. If a lift table is used, there is an additional, lightweight outer frame with an omega profile. 24-ton, 2-speed landing gear, single-sided operation, with a semi-circular lower part and a straight connection plate, with stroke compensation, free swivel radius to the rear approx.: 1950 mm, rear support, foldable 2 wheel chocks + holder Side underrun protection, aluminum Quarter panel fenders in front of and behind each axle with anti-splash flaps behind each axle Underrun protection, steel Splash flap at the rear over the entire width 4 storage boxes, stainless steel, w=800/h=350/d=350 mm, with a polished, lockable door, 2 x on the left front and 2 x on the right front in front of the 1st axle Hodoi Riw Aepfx Afwop Lift table behind the gooseneck, approx. 3000 mm long, hydraulically liftable for crossing over the gooseneck, with mechanical locking in the raised position. (Cylinder angled for good ground clearance, Fliegl standard). Operation on the right front + additional activation with a wireless remote control, lift table can be raised with the tarpaulin closed! Tarpaulin attachment in the lift table area to an additional, lightweight outer frame with omega profile, lift table can be raised with the tarpaulin closed! Lashing points can also be used in the lowered position! Lashing points Gooseneck: 4 pairs of 5-ton lashing points embedded in the outer frame 2 pairs of lashing points at the top and on the side embedded in the outer frame 8 pairs of lashing points at the top and on the side embedded in the outer frame, each 10 tons 9 pairs of 5-ton lashing points embedded in the outer frame Axles + Suspension SAF drum brake axles last axle with trailing steering knuckle, with automatic reversing lock via reversing light, and additional locking function on the vehicle via hand button. Air suspension with lifting and lowering valve + auto-reset function H&S function with quick vent 1st axle, automatic lift axle, incl. forced lowering and starting assist, activated by pressing the brake pedal 3 times (starting assist is functional up to an axle load exceedance of 30% and a speed of max. 25 km/h) Axle lift below the recommended ride height, no guarantee for tire damage Wheels and tires 235/75R17.5 from leading manufacturers Steel rims in twin arrangement, factory silver Braking system 2-line pneumatic braking system Spring brake parking brake 2 foolproof coupling heads at the front EBS, electronic braking system with EBS socket at the front, without connection cable Note: The trailer may only be towed by towing vehicles that ensure the effectiveness of the ABS! Axle load recognition in the truck via EBS, without installation in the truck. Electrical system 24 volts, multi-chamber lights, yellow LED lighting on the sides 2 white

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 3,000 kg, maximum load weight: 15,000 kg, overall weight: 18,000 kg, axle configuration: 2 axles, total length: 9,470 mm, total width: 2,550 mm, total height: 1,040 mm, suspension: air, tire size: 235/75 R17,5", tire condition: 100 %, Customized Transport Solution Configure your Fliegl vehicle to meet your specific requirements. The vehicle shown is an example. Production and equipment are customized according to customer specifications. *Chassis with swivel turntable Fine-grained steel welded construction Front stop, longitudinally adjustable and foldable 2 pairs of removable guide rollers, front and rear 1 pair of removable guide rollers, additional 4 container locks with sturdy 20"-based arms for swap bodies 7.15 and 7.45 Hsdpozfp Uxsfx Afwop Swivel frame with heavy-duty ball bearing swivel ring Wheel chocks with holder Aluminum side impact protection Side impact protection set inward for optimal clearance to the swap body supports Steel underrun protection Underrun protection shortened for optimal clearance to the swap body supports; lighting system mounted in a protected position Rear mud flaps across the entire width (not compatible with forklift mount) Quarter-shell front fenders and half-shell rear fenders *Towing equipment for trailer turntable Towing fork with certified 40 mm tow eye Towing fork mechanically adjustable in length by approx. 6 x 100 mm (approx. 1900–2500 mm), towing fork length set to 2200 mm *Axles + Suspension BPW or SAF drum brake axles, at the manufacturer’s discretion “Laser-aligned axles/chassis” to reduce tire wear and fuel consumption Air suspension *Brake System 2-line compressed air brake system Color-coded piping for easy maintenance. Air reservoir: 180 liters Spring-loaded parking brake 2 non-reversible coupling heads at the front, with connecting lines to the tractor unit, EBS, Electronic Braking System with EBS connector at the front, with connecting cable, Caution: The trailer may only be towed by tractor units that ensure the effectiveness of the ABS! With lift/lower valve, hold function in both lower and lift positions Axle load detection via EBS CAN bus signal, for display in the cab; truck must be equipped accordingly *Wheels and Tires 235/75 R17.5, brand selected by the manufacturer Steel rims in twin configuration, factory silver *Electrical System 24 volts, multi-chamber lights, yellow LED side lighting linked to the turn signals (“flashing side lights”), LED license plate lighting (Note: With certain towing vehicles, false diagnostics may occur even though the function is working properly) 2 white LED front position lights 2 white/red LED rear lane-keeping lights 2 x 7-pin reverse-polarity-protected connectors at the front, with connecting cable, LED work lights on both sides (activated via reverse light) 2 additional LED work lights at the rear, activated by the reverse light 1 LED work light at the front, centered between the cross members, shining toward the rear, activated by the reverse light *Country of Registration / License Plates Germany With DEKRA inspection and certification (in accordance with §13 EG - FGV) 24/7 Service Hotline Prepared for single-line license plate holders Contour markings with reflective strips in accordance with ECE R 048, white on the sides and red at the rear *Paint finish Hot-dip galvanized frame, including passivation “15-year warranty against rust-through” Drawbar: galvanized or black, at the manufacturer’s discretion Customized transport solution

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 2,950 kg, maximum load weight: 15,050 kg, overall weight: 18,000 kg, axle configuration: 2 axles, total length: 9,470 mm, total width: 2,550 mm, total height: 1,080 mm, suspension: air, tire size: 445/45 R19,5", tire condition: 100 %, Customized Transport Solution Configure your Fliegl vehicle to meet your specific requirements. The vehicle shown is an example. Production and equipment are customized according to customer specifications. *Chassis with swivel turntable Fine-grained steel welded construction Fliegl “V-Stream” frame Front stop, longitudinally adjustable and foldable Pair of removable guide rollers, front and rear 4 container locks with sturdy arms based on 20" dimensions for 7.15 m and 7.45 m swap bodies (Note: When used in combination with the impact guard, the guard protrudes beyond the 7.15 m swap body) Note! Not suitable for 20" containers, or only possible if the container has a tunnel or opening at the front center measuring approx. 200 mm in length and 800 mm in width! Swivel mount with heavy-duty ball bearing swivel ring Wheel chocks with holders Aluminum side impact protection Side impact protection set inward for optimal clearance to the swap body supports Steel underrun protection Underrun protection shortened for optimal clearance to the swap body supports; lighting system mounted in a protected position Quarter-shell fenders in front and half-shell fenders in the rear Includes mud flaps for fenders Large Fliegl mud flap mounted transversely on the underrun protection at the rear *Trailer coupling system (turntable) Drawbar with certified 40 mm drawbar eye *Axles + Suspension SAF disc brake axles “Laser-measured axles/chassis” reduces tire wear and fuel consumption Air suspension *Brake System 2-line compressed air brake system Hsdpozfp S Dofx Afwop Color-coded lines for easy maintenance. Air reservoir capacity: 208 liters Spring-loaded parking brake 2 non-reversible coupling heads at the front, with connecting lines to the tractor unit, 24-volt EBS, electronic braking system with EBS connector at the front, with connecting cable, Caution: The trailer may only be towed by tractor units that ensure the effectiveness of the ABS! with lift & lower valve + auto-reset function Axle load detection via EBS CAN bus signal, for display in the cab; the truck must be equipped accordingly “TPMS” tire pressure monitoring system according to ECE R 141, display in the towing vehicle via EBS *Wheels and tires 445/45 R19.5", brand selected by the manufacturer Steel rims, factory silver *Electrical system 24 volts, multi-chamber lights, yellow LED side lighting Yellow LED side lighting linked to the turn signals “Flashing side lights” 2 white front position lights 2 white/red rear lane-keeping lights 1 x 15-pin connector at the front, with connecting cable, additional LED work light(s) at the rear, activated via the reverse light LED work light at the front, centered between the cross members, shining toward the rear, activated via the reverse light *Country of registration/license plates Germany with DEKRA approval and certification (in accordance with §13 EG - FGV) 24/7 service hotline prepared for single-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white on the sides and red at the rear *Chassis galvanized or painted in colour of choice

Condition: used, overall weight: 38,000 kg, axle configuration: 3 axles, first registration: 06/2016, loading space length: 13,620 mm, loading space width: 2,480 mm, loading space height: 3,000 mm, loading space volume: 101 m³, Equipment: ABS, Vehicle identification number: WFDFLT33802019495 First registration: 06/02/2016 DE MOT until 06/2027 / SP until 12/2026 Unladen weight: 6,057 kg ----large portal doors Internal height: 3,000 mm L-profile Side loading height: 2,880 mm Pallet stop bar on the right and left BPW ECO Plus axles with disc brakes LIFT AXLE Sliding curtain, Edscha Toolbox Tires: 435/50 R 19.5 Spare wheel holder WITHOUT spare wheel Changes, prior sale and errors are expressly reserved. The description serves to generally identify the vehicle and does not constitute a guarantee in the legal sense of purchase. The description according to the purchase contract is decisive. Hjdpozfuhdsfx Afwsp Our offer generally does not include a new TÜV inspection. If a new TÜV inspection is desired, we will be happy to provide you with a quote from our partner workshops! The vehicle may be covered with and/or labeled with advertising. Our general delivery and payment terms apply.

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 2,500 kg, maximum load weight: 15,500 kg, overall weight: 18,000 kg, axle configuration: 2 axles, total length: 9,470 mm, total width: 2,550 mm, total height: 1,260 mm, suspension: air, tire size: 385/65 R22,5", tire condition: 100 %, Customized Transport Solution Configure your Fliegl vehicle to meet your specific requirements. The vehicle shown is an example. Production and equipment are customized according to customer specifications. *Chassis with swivel turntable Fine-grained steel welded construction Fliegl “V-Stream” frame Front stop, longitudinally adjustable and foldable 2 pairs of removable guide rollers, front and rear 4 container locks with sturdy 20"-based arms for 7.15- and 7.45-meter swap bodies Note! Not suitable for 20" containers, or only possible if the container has a tunnel or opening at the front center approximately 200 mm long and 800 mm wide! Swivel frame with heavy-duty ball bearing swivel ring 2 wheel chocks with holders Aluminum side impact protection Side impact protection set inward for optimal clearance to the swap body supports Steel underrun protection Underrun protection shortened for optimal clearance to the swap body supports; lighting system mounted in a protected position Half-shell fenders Rear mud flaps across the entire width *Trailer Coupling Device (Turntable) Towing fork with certified 40 mm tow eye Spring-loaded towing fork height adjustment *Axles + Suspension SAF disc brake axles “Laser-measured axles/chassis” reduces tire wear and fuel consumption Air suspension *Brake System 2-line compressed air brake system; color-coded lines for easy servicing. Air reservoir: 208 liters Spring-loaded parking brake 2 non-reversible coupling heads at the front, with connecting lines to the tractor unit, EBS, Electronic Brake System with EBS connector at the front, with connecting cable, Caution: The trailer may only be towed by towing vehicles that ensure the effectiveness of the ABS! With lift/lower valve, hold function in both lower and lift positions *Wheels and Tires 385/65 R22.5" Manufacturer’s choice Steel rims, factory silver, ET 120 *Electrical System 24 volts, multi-chamber lights, yellow LED side lighting 2 white front position lights 2 white/red rear lane-keeping lights 2 x 7-pin reverse-proof connectors at the front, with connecting cable, 2 additional LED work lights at the rear, activated by the reverse light 1 LED work light at the front, centered between the cross members, shining toward the rear, activated by the reverse light *Country of Registration/License Plates Germany with DEKRA approval and certification (in accordance with §13 EG - FGV) 24/7 service hotline prepared for single-line license plate holder Contour marking with reflective strips per ECE R 048, white on the sides and red at the rear Hodpfx Afszd U Uuswjp *Paint finish Frame Hot-dip galvanized or painted according to customer specifications Customized transport solution Configure your Fliegl vehicle to meet your requirements. The vehicle shown is an example. Production and equipment are customized according to customer specifications.

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 3,100 kg, maximum load weight: 14,900 kg, overall weight: 18,000 kg, axle configuration: 2 axles, total length: 9,970 mm, total width: 2,550 mm, total height: 1,250 mm, suspension: air, tire condition: 100 %, Customized Transport Solution Configure your Fliegl vehicle to meet your specific requirements. The vehicle shown is an example. Production and equipment are customized according to customer specifications. *Chassis for central-axle trailer Fine-grained steel welded construction Front stop, transverse, in a foldable/adjustable design, as previously delivered with AU 257359 1 pair of removable guide rollers, front and rear 1 additional pair of removable guide rollers 4 container locks with sturdy arms based on 20" for swap bodies 7.45 m and 7.82 m 1 pair of front transmission support legs, with straight lower section and single-side operation on the right side 1 pair of rear transmission support legs, with straight lower section and single-side operation on the right side (FR) Side impact protection set inward, for optimal clearance to the swap body supports Steel underrun protection *Towing equipment for central-axle trailers Towing beam with certified 50 mm tow eye, freight forwarding version Flat flange plate for tractors with underrun-protected LBW, connected to the drawbar at the top and bottom Drawbar clamped/bolted, easily replaceable and partially adjustable in length! Under-coupler drawbar, free drawbar length approx. 2150 mm Folding bracket with spring support on the drawbar, for routing the connection cables to the truck *Axles + Suspension SAF or BPW disc brake axles “Laser-aligned axles/chassis” reduces tire wear and fuel consumption Travel odometer/odometer Air suspension *Brake System 2-line compressed air brake system Color-coded lines for easy servicing. Air reservoir: 208 liters Spring-loaded parking brake, Hsdpfx Afezd U I Ujwsp Control panel in the front right Duomatic connection at the front, with connecting line to the tractor unit, connection in the front right 24-volt EBS, electronic braking system with EBS connector at the front, with connecting cable, connection in the front right Caution: The trailer may only be towed by towing vehicles that ensure the effectiveness of the ABS! With lift & lower valve, hold function in both lower and lift positions Vehicle – Vehicle Stability Control System Brake release function via a pushbutton on the vehicle next to the lift & lower valve, for releasing the brake when coupled; EBS power supply must be ensured! “TPMS” Tire Pressure Monitoring System according to ECE R 141, display in the towing vehicle via EBS *Wheels and Tires 385/65 R22.5" steel rims, factory silver *Electrical System 24 volts, multi-chamber LED lights, yellow LED side lights, LED license plate lights, (Note: With certain towing vehicles, false diagnostic errors may occur even though the system is functioning properly) Yellow LED side lights linked to the turn signals “Flashing side lights” Parking sockets for electrical and air connections on the drawbar 2 white LED front position lights 2 white/red LED rear lane-keeping lights 1 x 15-pin connector at the front, with connecting cable, located on the right rear 2 additional LED work lights, recessed and integrated into the rear, activated by the reverse light 1 LED work light at the front, centered between the cross members, shining toward the rear, activated by the reverse light *Country of Registration/License Plates Prepared for single-line license plate holder Night parking sign at front and rear *Paint Finish Frame Hot-dip galvanized or painted according to customer preference

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 3,230 kg, maximum load weight: 14,770 kg, overall weight: 18,000 kg, axle configuration: 2 axles, total length: 10,020 mm, total width: 2,550 mm, total height: 870 mm, suspension: air, tire size: 235/75 R17,5", tire condition: 100 %, *Wechel Central-Axle Trailer Chassis Fine-grained steel welded construction Front stop, longitudinally adjustable and foldable 2 pairs of removable guide rollers, front and rear Locks height-adjustable by approx. 120 mm for parking height 1070 mm, lifting height then approx. 1150 mm, and driving height then approx. 990 mm; foldable with center supports. Includes guide rollers that can be inserted into center supports (locking mechanism from the Vario chassis at the rear) 4 container locks with sturdy arms on a 20" base for swap bodies 7.15 / 7.45 and 7.82 1 pair of front transmission support legs, with straight lower section and single-sided operation on the right rear Foldable rear support 2 wheel chocks with holder Aluminum side impact protection Steel underrun protection Half-shell fenders 1 spare wheel holder for 1 electric bike, with wheel mounting kit 1 plastic toolbox, with insert shelf, W=620/H=360/D=440 mm, lockable with a padlock. (Lock not included) *Towing equipment for central-axle trailer Towing beam with certified 50 mm tow eye, freight transport version (not suitable for trucks with tail lifts; detailed verification may still be required when placing an order) Towing beam lower coupler, free towing beam length approx. 2200 mm Folding bracket with spring support on the towing beam, for routing the connection cables to the truck *Axles + Suspension SAF drum brake axles “Laser-aligned axles/chassis” Reduces tire wear and fuel consumption Air suspension *Brake System 2-line compressed air brake system Color-coded lines for easy servicing. Spring-loaded parking brake 2 non-reversible coupling heads at the front, with connecting lines to the motor vehicle, connection at FR-right EBS, Electronic Brake System with EBS connector at the front, with connecting cable, connection at FR-right Caution: The trailer may only be towed by towing vehicles that ensure the effectiveness of the ABS! With lift/lower valve, hold function in both lower and lift positions Hsdpjzd Uyqsfx Afwsp Vehicle – Vehicle Stability System *Wheels and Tires 235/75 R17.5, brand selected by the manufacturer Steel rims in twin configuration, factory silver *Electrical System 24 volts, multi-chamber lights, yellow LED side lighting 2 white front position lights 2 white/red rear lane-keeping lights 1 x 15-pin connector at the front, with connecting cable, connection at the rear right 2 additional LED work lights at the rear, activated via the reverse light 1 LED work light at the front, centered between the cross members, shining toward the rear, activated via the reverse light *Operating Instructions The specified total weight is technically possible; however, depending on the cargo, the total weight may not be reached while complying with the permissible axle, support, and fifth-wheel loads. (Poor handling and tracking may result from improper load distribution) *Country of Registration/License Plates Germany With DEKRA approval and certification (in accordance with §13 EG-FGV) 24/7 Service Hotline Prepared for single-line license plate holders Contour markings with reflective strips in accordance with ECE R 048, white on the sides and red at the rear *Paint Finish Frame Hot-dip galvanized or painted according to customer specifications

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 3,000 kg, maximum load weight: 15,000 kg, overall weight: 18,000 kg, axle configuration: 2 axles, total length: 9,470 mm, total width: 2,550 mm, total height: 1,040 mm, suspension: air, tire size: 235/75 R17,5", tire condition: 100 %, Customized Transport Solution Configure your Fliegl vehicle to meet your specific requirements. The vehicle shown is an example. Production and equipment are customized according to customer specifications. *Chassis with swivel turntable Fine-grained steel welded construction Front stop, longitudinally adjustable and foldable 2 pairs of removable guide rollers, front and rear 1 pair of removable guide rollers, additional 4 container locks with sturdy 20"-based arms for swap bodies 7.15 and 7.45 Swivel frame with heavy-duty ball bearing swivel ring Wheel chocks with holder Aluminum side impact protection Side impact protection set inward for optimal clearance to the swap body supports Steel underrun protection Underrun protection shortened for optimal clearance to the swap body supports; lighting system mounted in a protected position Rear mud flaps across the entire width (not compatible with forklift mount) Quarter-shell front fenders and half-shell rear fenders *Towing equipment for trailer turntable Towing fork with certified 40 mm tow eye Towing fork mechanically adjustable in length by approx. 6 x 100 mm (approx. 1900–2500 mm); towing fork length set to 2200 mm *Axles + Suspension BPW or SAF drum brake axles, at the manufacturer’s discretion “Laser-aligned axles/chassis” to reduce tire wear and fuel consumption Air suspension *Brake System 2-line compressed air brake system Color-coded piping for easy maintenance. Hjdpezd Uvlofx Afwep Air reservoir: 180 liters Spring-loaded parking brake 2 non-reversible coupling heads at the front, with connecting lines to the tractor unit, EBS, Electronic Brake System with EBS connector at the front, with connecting cable, Caution: The trailer may only be towed by tractor units that ensure the effectiveness of the ABS! With raise/lower valve, hold function in both lower and raise positions Axle load detection via EBS CAN bus signal, for display in the cab; the truck must be equipped accordingly; no truck installation (no calibrated scale) Tire pressure monitoring system *Wheels and tires 235/75 R17.5, brand selected by the manufacturer Steel rims in twin configuration, factory silver *Electrical System 24 volts, Aspöck Eco LED II multi-chamber lights, yellow LED side lighting linked to the turn signals (“flashing side lights”), LED license plate lighting, (Note: With certain towing vehicles, false diagnostics may occur even though the system is functioning properly) 2 white LED front position lights 2 white/red rear lane-keeping lights (LED) 2 x 7-pin reverse-polarity-protected connectors at the front, with connecting cable, LED work lights on both sides (activated by the reverse light) 2 additional LED work lights at the rear, activated by the reverse light 1 LED work light at the front, centered between the crossbars, shining toward the rear, activated by the reverse light *Country of Registration/License Plates Germany with DEKRA approval and certification (in accordance with §13 EG - FGV) 24/7 service hotline prepared for single-line license plate holders Contour marking with reflective strips in accordance with ECE R 048, white on the sides and red at the rear *Paint Finish Frame hot-dip galvanized or painted according to customer preference

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 3,250 kg, maximum load weight: 14,750 kg, overall weight: 18,000 kg, axle configuration: 2 axles, total length: 10,020 mm, total width: 2,550 mm, total height: 1,250 mm, suspension: air, tire size: 385/65 R22,5", tire condition: 100 %, Customized Transport Solution Configure your Fliegl vehicle to meet your specific requirements. The vehicle shown is an example. Production and equipment are customized according to customer specifications. *Chassis with central-axle trailer Fine-grained steel welded construction Front stop, longitudinally adjustable and foldable 2 pairs of removable guide rollers, front and rear 4 container locks with sturdy 20"-based arms for 7.15 m, 7.45 m, and 7.82 m swap bodies (Note: When used in combination with the impact guard, the guard protrudes beyond the 7.15 m swap body) 1 pair of front transmission support legs, with straight lower section and single-side operation on the right rear 1 pair of transmission support legs at the rear, with straight lower section and single-side operation on the right side 2 wheel chocks with holders Aluminum side impact protection Hodpfx Afszd Udcowep Side impact protection set inward, for optimal clearance to the swap body supports Steel underrun protection Rear mud flaps across the entire width Half-shell fenders Mud flaps *Towing Equipment for Central-Axle Trailers Towing beam with certified 50 mm tow eye, freight carrier version Flat flange plate for tractors with a clearance-type low-bed trailer, connected to the towing beam at the top and bottom Towing beam clamped/bolted, easily replaceable, and partially adjustable in length! Lower coupler drawbar, free drawbar length approx. 2200 mm Fold-down bracket with spring assistance on the drawbar, for routing the connection cables to the truck *Axles + Suspension BPW disc brake axles “Laser-measured axles/chassis” reduces tire wear and fuel consumption Air suspension *Brake system 2-line compressed air brake system Color-coded wiring for easy servicing. Air reservoir: 208 liters Air-spring parking brake, Control panel at the rear right Duomatic connection at the front, with connecting line to the tractor unit, connection at the rear right 24-volt EBS, electronic braking system with EBS connector at the front, with connecting cable, connection at the rear right Caution: The trailer may only be towed by towing vehicles that ensure the effectiveness of the ABS! With lift and lower valve, hold function in both lower and lift positions Vehicle - Vehicle Stability Control System *Wheels and Tires 385/65 R22.5" Manufacturer's choice Steel rims, factory silver *Electrical System 24 volts, multi-chamber lights, yellow LED side lighting Connectors for electrical and air connections on the drawbar 2 white front position lights 2 white/red rear lane-keeping lights 1 x 15-pin connector at the front, with connecting cable, connection at FR-right 2 additional LED work lights, recessed and integrated into the rear, activated via the reverse light 1 LED work light at the front, centered between the cross members, shining toward the rear, activated via the reverse light *Country of Registration/License Plates Germany With DEKRA approval and certification (per §13 EG - FGV) 24/7 service hotline Prepared for single-line license plate holder Warning sign per ECE - 70 Night parking sign front and rear Contour markings with reflective strips in accordance with ECE R 048, white on the sides and red at the rear *Paint finish Frame Hot-dip galvanized or painted according to customer specifications

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 3,220 kg, maximum load weight: 14,780 kg, overall weight: 18,000 kg, axle configuration: 2 axles, total length: 10,020 mm, total width: 2,550 mm, total height: 1,070 mm, suspension: air, tire size: 445/45 R19,5", tire condition: 100 %, Customized Transport Solution Configure your Fliegl vehicle to meet your specific requirements. The vehicle shown is an example. Production and equipment are customized according to customer specifications. *Chassis for swap body with central axle trailer Fine-grained steel welded construction Front stop, longitudinally adjustable and foldable 2 pairs of removable guide rollers, front and rear Swap Guard – swap body guide, in front of and behind each container lock Hodpfx Aszd Tw Iefwjp 4 container locks with sturdy 20"-based arms for 7.15, 7.45, and 7.82 swap bodies 1 pair of front gear support legs, with straight lower section and single-sided operation on the right side 2 wheel chocks with holders Aluminum side impact protection Steel underrun protection Rear mud flaps across the entire width (not compatible with forklift mount) 4 half-shell fenders Mud flaps Spare tire mount for 1 electric bike, with wheel mounting kit Towing equipment for central-axle trailer Towing beam with certified 50 mm tow eye, freight forwarding version (not suitable for trucks with tail lifts; detailed verification may still be required on a case-by-case basis) Towing bar coupler, free towing bar length approx. 2200 mm Folding bracket with spring assistance on the towing bar, for routing the connection cables to the truck *Axles + Suspension SAF disc brake axles “Laser-measured axles/chassis” reduces tire wear and fuel consumption Air suspension *Brake System 2-line compressed air brake system Color-coded piping for easy maintenance. Air reservoir capacity: 208 liters Spring-loaded parking brake 2 non-reversible coupling heads at the front, with connecting lines to the motor vehicle, connection at FR-right EBS, Electronic Braking System with EBS connector at the front, including connecting cable, connection at FR-right Caution: The trailer may only be towed by towing vehicles that ensure the effectiveness of the ABS! With lift/lower valve, hold function in both lower and lift positions *Wheels and Tires 445/45 R19.5", brand selected by the manufacturer Steel rims, factory silver *Electrical system 24 volts, 4 x 3-chamber lights + 1 round backup light and + 1 round rear fog light, yellow LED lighting on the sides 2 white front position lights 2 white/red rear lane-keeping lights 1 x 15-pin connector at the front, with connecting cable, connection at the rear right 2 Additional LED work light(s) at the rear, activated via the reverse light *Country of registration/license plates Germany With DEKRA approval and certification (in accordance with §13 EG-FGV) 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips per ECE R 048, white on the sides and red at the rear *Paint finish Frame Hot-dip galvanized or painted per customer request

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 3,250 kg, maximum load weight: 14,750 kg, overall weight: 18,000 kg, axle configuration: 2 axles, total length: 10,020 mm, total width: 2,550 mm, total height: 1,120 mm, suspension: air, tire size: 385/55 R22,5", tire condition: 100 %, Customized Transport Solution Configure your Fliegl vehicle to meet your specific requirements. The vehicle shown is an example. Production and equipment are customized according to customer specifications. *Chassis for central-axle swap trailers Fine-grained steel welded construction Front stop, longitudinally adjustable and foldable Pair of removable guide rollers, front and rear 4 container locks with sturdy 20"-based arms for 7.15 m, 7.45 m, and 7.82 m swap bodies (Note: When used in combination with the impact guard, the guard protrudes beyond the 7.15 m swap body) 1 pair of front gear-driven support legs, with straight lower section and single-sided operation on the right side 1 pair of rear gear-driven support legs, with straight lower section and single-sided operation on the right side Side impact protection set inward, for optimal clearance to the swap body supports Steel underrun protection Rear mud flaps across the entire width *Towing equipment for central-axle trailers Towing beam with certified 50 mm tow eye, freight forwarding version Towing beam clamped/bolted, easily replaceable and partially adjustable in length! Lower coupler on towing beam, free towing beam length approx. 2200 mm Folding bracket with spring support on the towing beam, for routing the connection cables to the truck *Axles + Suspension SAF disc brake axles “Laser-aligned axles/chassis” reduces tire wear and fuel consumption Air suspension without lift axle *Brake System 2-line compressed air brake system Color-coded lines for easy servicing. Air reservoir: 208 liters Spring-loaded parking brake Duomatic connection at the front, with connecting line to the tractor unit, connection at the rear right 24-volt EBS, electronic braking system with EBS connector at the front, with connecting cable, connection at the rear right Caution: The trailer may only be towed by towing vehicles that ensure the effectiveness of the ABS! With lift & lower valve, hold function in both lower and lift positions Vehicle – Vehicle Stability Control System Brake release function via a pushbutton on the vehicle next to the lift & lower valve, for releasing the brake while coupled; EBS power supply must be ensured! *Wheels and Tires 385/55 R22.5" Manufacturer's choice Steel rims, factory silver *Electrical System 24 volts, multi-chamber LED lights, yellow LED side lighting, LED license plate lighting, (Note: With certain towing vehicles, false diagnostics may occur even though the function is working properly) 2 white LED front position lights 2 white/red LED rear lane-keeping lights Hjdpfxozd Trrj Afwjp 1 x 15-pin connector at the front, with connecting cable, connection on the right rear Additional LED work light(s), recessed and integrated into the rear, activated via the reverse light LED work light at the front, centered between the cross members, shining toward the rear, activated via the reverse light *Country of Registration/License Plates Germany With DEKRA approval and certification (per §13 EG - FGV) 24/7 service hotline Prepared for single-line license plate holder Warning sign per ECE - 70 ADR warning sign at the rear, foldable Contour marking with reflective strips in accordance with ECE R 048, white on the sides and red at the rear *Paint finish Frame Hot-dip galvanized or painted according to customer specifications