Used Fliegl Semitrailers With Swap Body for sale (305)

Condition: new, machine/vehicle number: 2428b2018baf171e60fef6740, empty load weight: 8,900 kg, maximum load weight: 32,100 kg, overall weight: 41,000 kg, axle configuration: 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader semi-trailer Welded steel construction, fifth wheel plate with interchangeable 2 kingpin and 2 kingpin positions, 24 t. 2-speed support winch, single-sided operation, with straight lower section, without thrust compensation Folding rear support 2 wheel chocks with holder Rjdpfx Ahei Ri E Rezjl Aluminum side collision protection Rear spray flaps across the entire width Mudguards in front of 1st axle and rear of each axle with anti-spray, according to EC Widenings extendable to 3,000 mm (not in rear slope) (track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Storage compartment for wooden planks in the middle of the cargo bed Wooden planks 70 mm for widening to 3000 mm Low loader lashing eyes 2 pairs of ring lashing eyes, 5 tons each at the front on gooseneck 11 pairs of lashing mushrooms at the top and sides of the outer frame, 10 tons each 2 x on gooseneck 9 x distributed in the low loading area First lashing eye 250 mm from the front and last max. 250 mm from the rear, distance between lashing eyes not greater than 1100 mm 8 pairs of stake pockets embedded in the outer frame, inside 70 x 40 mm, (can be converted to 5 to. ring lashing eyes, not included in the scope of delivery) Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Air suspension Wheels and tires 235 / 75 R 17.5 brand of the manufacturer's choice Twin steel rims, factory silver Brake system 2-line compressed air brake system Colored line routing for easy servicing. Spring-applied parking brake EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! 2 swap-proof coupling heads at the front, without connecting cable with lifting & lowering valve Axle load detection via EBS-Canbus signal, for indication via display in the driver's cab, truck must be prepared accordingly, no truck installed (no calibrated scales) Vehicle - driving stability system Electrical system 24 volt, multi-chamber lights, amber LED lighting on the side 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable sockets at the front, without connecting cable 1 LED rotating beacon with holder, switched via parking light (light can be removed) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Gooseneck with sheet steel covering Storage box recessed in drive-over slope to gooseneck Then with 70 mm softwood floor, steel/ checker plate covering in the wheel housing area Rear slope with 70 mm softwood floor Deep loading area incl. rear slope 9 200 mm Drive-on ramps Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways Covered with wood Hydraulic via tractor power take-off with throttle, actuation on the left side in FR Hydraulic connection with SVK socket NW 10/3, without connecting hoses Operating instructions With 10,000 kg axle load, a special permit is required, only indivisible load possible!!! Special permit required if total train weight exceeds 40 tons! The specified total weight is technically possible; depending on the load, the total weight may not be achieved while complying with the permissible axle/support and fifth-wheel loads. (Poor driving and trailing behavior possible due to incorrect load distribution) When applying for a special pe

Condition: new, machine/vehicle number: 15431365fe5515297a6a9fb05, overall weight: 24,000 kg, axle configuration: > 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction Turntable with powerful ball bearing slewing ring Folding rear support 2 wheel chocks with holder Aluminum side bumpers Rear spray flaps across the entire width Half-shell mudguards 1st + 2nd axle with anti-spray flaps behind each axle, anti-spray flaps in front of and behind 3rd and 4th axle Excavator trough above the rear axles starting to the rear, approx. 1800 mm long, approx. 650 mm wide and approx. 150 mm deep, 2 pairs of lashing holes each 5 tons in the excavator trough on the side of the longitudinal frame approx. 300 mm from the front and approx. 200 mm in front of the rear slope 1 plastic tool box, with shelf, w=620/h=360/t=440 mm, lockable with a padlock. (lock not included in scope of delivery) 1 storage box on offset recessed in floor with lid, W=720 mm/ L=520 mm / D= 170 mm Extensions extendable to 3,000 mm Wooden planks 70 mm for widening to 3000 mm Storage compartment for wooden planks under the loading area Low loader lashing eyes (40 lashing options) 1 pair of lashing eyes on offset per 5 tons 9 pairs of lashing points at the top and sides, each 10 tons, embedded in the outer frame 2 x front on offset 7 x in the drop deck 6 pairs of lashing holes in the outer frame of the low bed, each with 5 to. (lashing strap attachment) 3 additional pairs of hinged lashing eyes, 10 tons each 1 x inside next to the main frame at the start of the low bed 1 x on offset (protrudes) 1 x embedded in the floor behind the last axle Towing equipment Trailer turntable Drawbar with tested 50 mm drawbar eye, drawbar eye inclined 8° D-value min. 160 kN Axles + suspension Drum brake axles Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation front and rear (rocker compensation) Wheels and tires 235 / 75 R 17,5 at the manufacturer's choice Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 non-interchangeable coupling heads at the front, with connecting cables to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side Rsdpfei Ri A Sex Ahzsl 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin interchangeable plugs at the front, with connecting cable, 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Offset at the front with steel/ checker plate flooring Then with 70 mm softwood floor, steel/ checker plate covering in the wheel arch area Rear slope with 70 mm softwood flooring Drive-on ramps Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways covered with wood with spring lift support Country of registration / plates Country of registration: Germany 24/7 service hotline Prepared for two-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white on the sides and red on the rear Warning sign according to ECE - 70 Paintwork Hot-dip galvanized frame incl. passivation 15-year warranty against rusting through Drawbar Galvanized or black, at the manufacturer's discretion Drive-on ramps Hot-dip galvanized Attention! These are archive pictures!

Condition: new, machine/vehicle number: e763c8c2bb3370bd2342236a4, empty load weight: 3 kg, maximum load weight: 8 kg, overall weight: 11 kg, axle configuration: 2 axles, tire size: 235 / 75 r 17,5, Further information Chassis central axle tipping trailer Welded steel construction, continuous tipping shaft at the rear with 80 mm ball tipping bearing Gearbox support foot at the front 2 wheel chocks with holder Steel underride guard Lockable storage space for access ramps underneath the loading area Towing device central axle trailer Drawbar with tested 40 mm towing eye Height-adjustable drawbar via spindle, max. adjustment range 300 mm Axles + suspension Euro axles of our choice, with angular roller bearings and S-cam brake Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation (rocker compensation) Wheels and tires 235 / 75 R 17,5 at the manufacturer's choice Factory silver steel rims Brake system 2-line compressed air brake systemColor-coded cable routing for easy servicing. Hand spindle parking brake Integral air reservoir without ABS, but with mechanical ALB, then max. 60 km/h approval 2 swap-proof coupling heads at the front, with connecting lines to the motor vehicle, electrics 12 volt, multi-chamber lights, without amber LED lighting at the sides, reflectors at the sides 2 white position lights at the front 2 white/red lane departure lights at the rear 1 x 7-pin 12 volt plug at the front, with connecting cable, extended by approx. 60 cm Hydraulics Three-sided tipping mechanism, hydraulic multi-piston press with lift limiter and safety cable, Low-pressure cylinder up to max. 170 bar, without throttle. If necessary, this can be retrofitted to the truck. Hydraulic connection with SVK plug NW 10/3, incl. connection hose Hydraulic actuation via truck power take-off Tilting bridges Sturdy tipper body with 4 mm sheet steel floor, steel side wall structure, continuous side walls, hinged and pivoted with central locking at the bottom. Rear corner stanchions pluggable. Rear wall can be folded down and pivoted, with central locking at the bottom. Platform length approx. 4,500 mm, side walls with 5 hinges at the bottom. Platform width 2420 mm 5 pairs of lashing eyes in the floor, 5 tons each Operating instructions The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Country of registration: Germany with Dekra approval and expert opinion, for max. 60 km/h approval, towing vehicle LoF, (max. 40 km/h possible in Switzerland) Prepared for single-line license plate holder without contour marking / reflective strips according to ECE R 048, Rsdpfxji Rizbe Ahzel Paintwork Hot-dip galvanized frame incl. passivation 15-year warranty against rusting through Dropside/bridge RAL 3002 carmine red Please note! If the bridge is galvanized, it will not be painted! Note! Bridge only primed inside! Wide tires also possible for an extra charge. 355 / 60 R 18, then loading height approx. 980 mm Attention: Archive pictures!

Condition: new, machine/vehicle number: ebf3f771e96394cd89e56bbb7, overall weight: 11,800 kg, axle configuration: 2 axles, tire size: 235 / 75 r 17,5, Further information Chassis central axle trailer Welded fine-grained steel construction Rodpfx Aoi Rixrohzsl 6 pairs of lashing eyes bolted to the outside of the floor/outer frame, 5 tons each 2 pairs of lashing eyes additionally bolted to the floor, 5 tons each in the corners Gear support foot at the front Folding rear support 2 wheel chocks with holder Steel underride guard Rear spray flaps across the entire width Quarter-shell mudguards 1 plastic tool box, with shelf, w=620/h=360/t=440 mm, lockable with a padlock. (lock not included in scope of delivery) Towing device central axle trailer Towing bar with tested 40 mm towing eye Height-adjustable drawbar via spindle, max. adjustment range 300 mm Axles + suspension Drum brake axles, manufacturer's choice Axle/chassis laser-measured Reduction in tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation (rocker compensation) Wheels and tires 235 / 75 R 17,5 manufacturer's choice Factory silver steel rims Brake system 2-line compressed air brake system Hand spindle parking brake Integral air reservoir 2 non-interchangeable coupling heads at the front, with connecting cables to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin interchangeable plugs at the front, with connecting cable, Floor Steel/ checker plate floor for high point load capacity Note: Slight floor corrugation possible due to welding distortion! Platform length approx. 5,200 mm Rear sloping to approx. 900 mm Front wall / front corner stanchions 25 mm aluminum hollow profile, 400 mm high, Drop sides 25 mm aluminum hollow profile, 400 mm high, foldable and removable Rear wall / rear corner stanchions 1 pair of steel stanchions attached to the frame and with bracket for locking the drive-on ramps, drive-in width approx. 2,430 mm Drive-on ramps 2 steel ramps 2,300 mm long, 510 mm wide, can be moved sidewayswith grab handle on the ramps covered with 3 toothed steel rails With gas pressure jack for one-man operation Country of registration/plates Country of registration: Germany 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white on the sides and red on the rear Paintwork Hot-dip galvanized frame incl. passivation 15-year warranty against rusting through Front wall aluminum Side wall anodized aluminium Drive-on ramps Hot-dip galvanized Attention! These are archive pictures.

Condition: new, machine/vehicle number: f044065451f6d849ee7a5b9f8, empty load weight: 5 kg, maximum load weight: 29 kg, overall weight: 35 kg, axle configuration: 3 axles, tire size: 385 / 65 r 22,5, Further information Chassis semi-trailer forwarding Welded steel construction in reinforced design, only 2 side members as double T-beams with steel/checker plate between the side members, saddle plate with replaceable 2 kingpins. Protective plate for rear lights. 1 steel storage box, recessed between side members 8 pairs of lashing eyes bolted or welded to the frame at the manufacturer's choice 24 t. 2-speed support winch, single-sided operation, with straight lower section, without thrust compensation 2 wheel chocks with holder Aluminium side bumper Galvanized steel underride guard Half-shell mudguards with anti-spray flaps according to EC 1 spare wheel holder for 1 e-wheel, with wheel fastening set 8 wooden stanchions of the manufacturer's choice, bolted to frame with 2 wooden stanchions each, telescopic from 1800 to 2800 mm, per pair 7 to. Axles + suspension SAF disk brake axles with 430 mm disk diameter Air suspension with lifting & lowering valve, safety cable on the axles 1st axle automatic lift axle, including forced lowering and starting aid, actuation of 3x brakes (starting aid is functional up to an axle load excess of 30% and up to a speed of max. 25 km/h) Axle spacing offset mm (combined transport) up to 44 tons gross train weight Wheels and tires 385 / 65 R 22,5 at the manufacturer's discretion Steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake Axle load detection via EBS-Canbus signal, for indication via display in the cab, truck must be prepared accordingly, no truck installed (no calibrated scales) 2 swap-proof coupling heads at the front, without connecting cable EBS, electronic brake system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin and 1 x 15-pin interchangeable sockets at the front, without connecting cable Front bulkhead/front stanchions Steel/grid bulkhead, approx. 2,300 mm high, bolted to the frame Rodpfx Ahoi Rivwozol Approval / plates Country of approval: Germany Approval according to EC 2007/46 Prepared for single-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white at the sides and red at the rear Paint finish Frame DB 7350 nova gray Black coated support legs Front wall hot-dip galvanized Attention: Archive pictures!

Condition: new, machine/vehicle number: eca976917d325d4adc41b69e8, empty load weight: 7,200 kg, maximum load weight: 27,800 kg, overall weight: 35,000 kg, axle configuration: 3 axles, tire size: 385/65 r 22,5, Further information Chassis semitrailer forwarding Fine-grained steel welded construction in lightweight design, fifth wheel plate with replaceable 2 king pins, main frame reinforcement for 25 tons in the centre of gravity on 3 m loading length when pushed together. 13 pairs of hooks for lashing strap attachment welded onto the cross members 23 pairs of lashing eyes embedded in the outer frame, 3.5 tons each Outer frame with Load-Lock profile for lashing strap attachment Please note! Cannot be used with drop sides! 24 t. 2-speed support winch in reinforced design for loaded trailer, single-sided operation, with semicircular lower section and straight connecting plate, with thrust compensation Wheel chocks with holder Aluminum side bumper Underride guard Half-shell mudguards with anti-spray flaps according to EG 1 spare wheel holder for 1 electric wheel, with wheel mounting kit 1 closed stanchion stowage box, open at the top, below loading area, doors on both sides, w=450 mm/H=400/420 mm/t=2460 mm 6 pairs of extendable stanchion pockets, for 80x80 mm tubular stanchions, extendable from loading width 2000 mm to 3100 mm 4 pairs of stanchion pockets embedded in the outer frame, for 80x80 mm shaped tubes 11 stake pockets centrally recessed in the floor, for 80x80 mm shaped tubes, with reinforcement beam, each installed between the outer stake pockets 5 x 3 pairs of stanchion pockets recessed on the outside of the longitudinal beams, for 80x80 mm shaped pipes, including reinforcement beams - for securing loads to the front and rear when transporting 2x5000 mm or 2x 6000 mm construction steel mats 6 lightweight stanchions W=80/ D=80/, usable height approx. 1850 mm, hot-dip galvanized, top with cable guide for belt tensioning 12 lightweight stanchions W=80/ D=80/, usable height approx. 1850 mm, hot-dip galvanized, with lashing eyes welded to the bottom on both sides Rsdsi Ri Szopfx Ahzjl Note: stanchion pockets / stanchions are not designed for securing long materials, pipes etc. on their own without looping around them 2 plastic toolboxes, with drawer and shelf, w=650 / h=520 / d=670 mm, lockable with a padlock (lock not included) 6 construction steel winches with wire rope and counter hooks, with rope feed-through through the outer frame, 1 removable slip-on gear for construction steel winches - supplied loose (without bracket on the frame) Telescoping Main frame can be telescoped Extendable by max. 4,000 mm and can be arranged approx. every 500 mm Locking with pneumatic bolt locking + display Frame locking on both sides, actuation via hand knob, operation for brake/locking and suspension in FR-left in front of the axles Storage compartment between the side members when extended Axles + suspension SAF disc brake axles with 430 mm disc diameter Last axle self-steering, with automatic reversing lock via reversing light, and additional locking function on the vehicle via hand button, as well as manually via switch in the towing vehicle (pin 10), without truck installation. Offset axle spacing mm Air suspension 1st axle automatic lift axle, can also be operated electrically from the truck, with starting aid, without truck installation (starting aid is functional up to an axle load exceeding 30% and up to a speed of max. 25 km/h) Brake system 2-line compressed air brake system Colored cable routing for easy servicing Spring-loaded parking brake 2 swap-proof coupling heads at the front, without connecting line EBS make of the manufacturer's choice, electronic brake syst

Condition: new, machine/vehicle number: 535119ca408d3bd5a8e74be51, empty load weight: 6 kg, maximum load weight: 11 kg, overall weight: 18 kg, axle configuration: 2 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction Turntable with strong ball bearing slewing ring, storage box embedded in turntable front end Folding rear support Wheel chocks with holder Aluminum side collision protection Half-shell mudguards on 1st axle, quarter-shell mudguards in front of and behind the 2nd axle with anti-spray flaps behind each axle 1 plastic tool box, with shelf, w=620/h=360/t=440 mm, lockable with a padlock. (lock not included in scope of delivery) Widenings extendable to 3,000 mm (not in rear slope) (However, the track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm), storage compartment for wooden planks in the middle of the loading area, wooden planks 70 mm for widening to 3,000 mm, Low loader lashing eyes 3 pairs of lashing points each 10 tons integrated in the floor at the front 6 pairs of lashing points at the top and sides, each 10 tons, integrated in the outer frame 1 x according to the rest of the neck area distributed between them, spacing not greater than 1200 mm, 1 x rear slope 5 pairs of ring lashing eyes embedded in the outer frame, 5 tons each (instead of stake pockets) Trailer drawbar Turntable Drawbar with tested 40 mm drawbar eye Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Rjdoi Ri N Hjpfx Ahzol Parabolic suspension with maintenance-free steel-rubber bearings Wheels and tires 235 / 75 R 17,5 at the manufacturer's choice Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 non-interchangeable coupling heads at the front, with connecting cables to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white/red rear lane departure lights 2 white position lights at the front 1 rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm 2 x 7-pin interchangeable plugs at the front, with connecting cable, floor Front area steel floor, then with 70 mm softwood floor, steel/ checker plate flooring in the wheel arch area Rear slope with 70 mm softwood floor Low loading area incl. rear slope 8 200 mm Drive-on ramps Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways Additional ramp safety device hinged at the bottom (to prevent the ramps from slipping sideways, not in conjunction with hydraulic side ramp displacement) covered with wood with spring lift support Operating instructions A special permit is required for axle loads of 10,000 kg. The permit must be applied for individually in each federal state; the legislator does not have to give a commitment for 20 tons GG. Customer risk. The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. Approval / plates Country of approval: Germany Test approval according to EG 2007/46 24/7 service hotline Prepared for two-line license plate holder Contour markings with reflective strips to ECE R 048, white at the sides and red at the rear Warning sign according to ECE - 70 Paint finish Frame DB nova gray Drive-on ramps hot-dip galvanized Attentio

Condition: new, machine/vehicle number: a3b1347da4aa7f31dceb875db, empty load weight: 2 kg, maximum load weight: 9 kg, overall weight: 11 kg, axle configuration: 2 axles, tire size: 235 / 75 r 17,5, Further information Chassis central axle trailer Welded fine-grained steel construction 6 pairs of lashing eyes bolted to the outside of the floor/outer frame, 5 tons each Front gear support leg Folding rear support 2 wheel chocks with holder Steel underride guard Rear spray flaps across the entire width Quarter-shell mudguards Towing device central axle trailer Towbar with tested 40 mm towing eye Height-adjustable drawbar via spindle, max. adjustment range 300 mm Axles + suspension BPW drum brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation (rocker compensation) Wheels and tires 235 / 75 R 17,5 manufacturer's choice Factory silver steel rims Brake system 2-line compressed air brake system Hand spindle parking brake Integral air reservoir Rodpfx Asi Ri Ilehzol 2 non-interchangeable coupling heads at the front, with connecting cables to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin interchangeable plugs at the front, with connecting cable, Floor Steel/ checker plate floor for high point load capacity Note: Slight floor corrugation possible due to welding distortion! Platform length approx. 5,200 mm Rear sloping to approx. 900 mm Front wall / front corner stanchions 25 mm aluminum hollow profile, 320 mm high, Drop sides 25 mm aluminum hollow profile, 320 mm high, foldable and removable Rear wall / rear corner stanchions 1 pair of steel stanchions attached to the frame and with bracket for locking the drive-on ramps, drive-in width approx. 2,430 mm Drive-on ramps 2 steel ramps 2 300 mm long, 510 mm wide, can be moved sidewayswith grab handle on the ramps covered with wood With gas pressure jack for one-man operation Operating instructions The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Country of registration: Germany with Dekra approval and expert opinion (according to §13 EG - FGV) 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white at the sides and red at the rear Paint finish Frame DB 7350 nova gray10-year warranty against rusting through Front wall aluminum Side wall anodized aluminium Drive-on ramps Hot-dip galvanized Attention: Archive pictures!

Condition: new, machine/vehicle number: 8e6cf81e11b107f23f22f209a, axle configuration: 3 axles, tire size: 435/50 r19.5, Further information Fine-grained steel welded construction, with preload slight pretension in the neck area, saddle plate with replaceable 2 , kingpin, outer frame slightly inclined new design with Load-Lock profile for tensioning strap attachment, 24 to. 2-speed support winch, single-sided operation, with straight lower section, without thrust compensation Note: Free support leg corner dimension or free swing-through radius to the rear approx. 1930 mm, pull-out ladder at the rear, lateral door stop, 2 wheel chocks with holder, aluminium side collision protection, galvanized steel underride guard, quarter-shell mudguards in front of 1st axle and behind each axle, with anti-spray flaps according to EC, impact protection at the rear SAF disc brake axles, laser-measured axle/chassis to reduce tire wear and fuel consumption, air suspension 2-line compressed air brake system, colored cable routing for easy servicing, spring-loaded parking brake, 2 swap-proof coupling heads at the front, without connecting cable, EBS, electronic brake system with EBS socket at the front, without connecting cable, Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS, with lift & lower valve, vehicle stability system 435/50 R19.5 tires of the manufacturer's choice, steel rims, factory silver 24 volt, multi-chamber lights, amber LED lighting at the sides, 2 white position lights at the front, 2 white/red lane departure lights at the rear, 2 x 7-pin interchangeable sockets at the front, without connecting cable Floor: Screen printing plates approx. 30 mm thick, on longitudinal beams for high point load capacity for forklift axle load up to max. 7100 kg Front bulkhead / corner stanchions: 2,580 mm high, steel corner stanchions in volume design, release device for side tarpaulin on bulkhead, crash blocker, bottom inside at approx. 140 mm height with steel impact protection Center stanchions: 3 pairs of sliding stanchions can be moved along the entire length, with 4 insertion pockets and a long pocket at the bottom, 3 pairs of stanchion positions Insertion slats: 5 rows of wooden insertion slats Rear wall / rear corner stanchions: Rear steel corner stanchions up to the lower edge of the roof, attachment for tarpaulin with round tube and tarpaulin tensioning ratchet, rear portal doors, 2-leaf with 2 internal espagnolette locks each Tarpaulin: Tarpaulin with welded-in horizontal and vertical straps, stainless steel tensioning fasteners Rodpji Ri E Hjfx Ahzsl Roof: Sliding roof, rear end lift can be folded up, with roof can be pushed from rear to front, L-shaped roof rail for car industry, internal width between the roof rails, approx. 2 490 mm, tarpaulin color: white, 400 Roof non-elastic, hardly any deflection of the roof rail when loading and unloading, optimum rain strip at the rear, at the top of the end bows, above the doors, EcoLift - lifting roof can be raised by approx. 380 mm, with gas pressure damper support, 3 driving positions at the front: interior height at the front approx. 2900 mm/ 2950 mm / 3000 mm, adjusted to approx. 3000 mm Germany, test approval according to EC 2007/46, 24/7 service hotline, Fliegl manufacturer's certificate for structural strength according to EN 12642 XL, prepared for single-line license plate holder, warning sign according to ECE - 70, reflective strips: white, continuous on the side tarpaulin at the bottom and at the top in the corners (if visible drop sides, then the strip at the bottom, on

Condition: new, machine/vehicle number: 74dd481d88dffaf9218e6ee58, empty load weight: 5,150 kg, maximum load weight: 29,850 kg, overall weight: 35,000 kg, axle configuration: 3 axles, tire size: 385/65 r22,5, Further information Chassis tipper semi-trailer Fine-grained steel welded construction, in basic lightweight design, fifth wheel plate with interchangeable 2 kingpins Patented curved front end Telescopic support in the middle, unhitching with load not possible, when unhitched the vehicle must be at an angle to the rear. Wheel chocks with holder Underride guard, foldable Half-shell mudguards Integrated mudguard holder Stone-repellent surface with anti-spray flaps on last axle only Tarpaulin pole with bracket Tow hook at the rear Axles+suspension SAF disc brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Axles in off-road version, Air suspension 1st axle automatic lift axle, including forced lowering and starting aid, actuation of 3x brakes (starting aid is functional up to an axle load excess of 30% and up to a speed of max. 25 km/h) Hot-dip galvanized lift axle mechanism 10-year warranty against rusting through Brake system 2-line compressed air brake systemColor-coded cable routing for easy servicing. Spring-loaded parking brake 2 interchangeable front clutch heads, without connecting line EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve Vehicle stability system Automatic tilt lowering with shut-off valve Wheels and tires 385/65 R22.5 Steel rims, factory silver Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable sockets at the front, without connecting cable Rjdpfx Ahoi Ri A Iszel Hydraulics Low-pressure cylinder max. 170 bar, smallest stage hard-chlorinated, with HDK screw socket, fixed part, NW 48 mm (without hose connection). Hydraulic actuation via truck power take-off Troughs Round steel body in Stone Master design made of highly wear-resistant HB 400/450 steel. Sloping front wall with external hydraulic en with access to front wall. Greenline - conical and aerodynamic body shape Bucket and brush holder on the outside of the front wall. Membrane rear wall Rear wall as swing flap with double-jointed hinge, resting on the outside with double hook lock. 2 clamping screws with toggle fasteners at the bottom side. Side walls 4 mm thick throughout, base 4/5 mm thick, wear and weight-optimized design, Standing platform with step, connection plate for air/electric and brake with large clearance for optimum operability. Roller tarpaulin on one side for depositing in FR-right, with central locking in FR-left Operating instructions For salt, lime, etc. We recommend a tipping cylinder with a hard chrome-plated piston rod so that it is not attacked by the material and rusts. The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Germany Test approval according to EC 2007/46 Body strength according to EN 12642 24/7 service hotline Prepared for single-line license plate holder Warning sign according to ECE - 70 Contour markings with reflective strips to ECE R 048, white at the sides and red at the rear Paint finish Frame DB 7350 nova gray10-year warranty

Condition: new, machine/vehicle number: 2dee9cc4124b79c4820f5c3cf, overall weight: 35,000 kg, axle configuration: 3 axles, tire size: 385/65 r22.5, Further information Fine-grained steel welded construction, saddle plate with replaceable 2 , kingpin, outer frame slightly inclined new design with Load-Lock profile for tensioning strap attachment, 24 to. 2-speed support winch, single-sided operation, with straight lower section, without thrust compensation Note: Free support leg corner dimension or free swing-through radius to the rear approx. 1930 mm, pull-out ladder at the rear, door stop at the side, 2 wheel chocks with holder, Aluminium side collision protection, galvanized steel underride guard, quarter-shell mudguards in front of and behind axle unit, with anti-spray flaps in accordance with EC, impact protection at the rear SAF disc brake axles with 430 mm disc diameter, axle/chassis laser-measured Reduction in tire wear and fuel consumption, air suspension 2-line compressed air brake system, colored cable routing for easy servicing, spring-loaded parking brake, 2 swap-proof coupling heads at the front, without connecting cable, EBS, electronic brake system with EBS socket at the front, without connecting cable, Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS, with lift & lower valve, vehicle stability system 385/65 R22.5 tires of the manufacturer's choice, steel rims, factory silver 24 volt, multi-chamber lights, amber LED lighting at the sides, 2 white position lights at the front, 2 white/red lane departure lights at the rear, 2 x 7-pin interchangeable sockets at the front, without connecting cable, Floor: Screen printing plates approx. 30 mm thick, on longitudinal beams for high point load capacity for forklift axle load up to max. 7100 kg Front bulkhead / corner stanchions: 2,580 mm high, steel corner stanchions in volume design, release device for side tarpaulin on bulkhead, crash blocker, bottom inside at approx. 140 mm height with steel impact protection Center stanchions: 3 pairs of sliding stanchions can be moved along the entire length, with 4 insertion pockets and long pocket at the bottom, 3 pairs of stanchion positions Rsdpfoi Riy Tjx Ahzsl Insertion slats: 5 rows of wooden insertion slats Rear wall / rear corner stanchions: Rear steel corner stanchions up to the lower edge of the roof, attachment for tarpaulin with round tube and tarpaulin tensioning ratchet, rear portal doors, 2-leaf with 2 internal espagnolette locks each Tarpaulin: tarpaulin with welded horizontal and vertical straps, stainless steel tensioning fasteners Roof: Sliding roof, rear end lift can be folded up, with roof can be slid from rear to front, L-shaped roof rail for automotive industry, internal width between the roof rails, approx. 2,490 mm, tarpaulin color: white, 400 Roof non-elastic, hardly any deflection of the roof rail when loading and unloading, optimum rain strip at the rear, at the top of the end bows, above the doors Germany, test approval according to EC 2007/46, 24/7 service hotline, Fliegl manufacturer's certificate for structural strength according to EN 12642 XL, prepared for single-line license plate holder, warning sign according to ECE - 70, reflective strips: white, continuous on the side tarpaulins at the bottom and at the top in the corners (if visible drop sides, then the strip at the bottom, on the drop sides), reflective strips: red, all-round on the rear portal Frame DB 7350 nova grey, 10-year warranty against rusting through, support legs coated black, front corner stanchions hot-dip galvanized, front wall aluminium, rear corner

Condition: new, machine/vehicle number: a198a229880f94ce822d671fc, empty load weight: 3 kg, maximum load weight: 16 kg, overall weight: 20 kg, axle configuration: 1 axle, tire size: 385 / 65 r 22,5, Further information Chassis semi-trailer container Welded fine-grained steel construction, saddle plate with replaceable 2 king pins, 2 pairs of removable guide rollers 4 container locks with sturdy outriggers on 20 -base for swap bodies 7.45 and 7.82 24 t. 2-speed support winch, single-side operation, with straight lower section, without thrust compensation, unhitching under load only possible with even outreach! 2 wheel chocks with holder Aluminium side bumper Galvanized steel underride guard, Half-shell mudguards with anti-spray flaps Rjdpfx Aji Rixnjhzel Axle+suspension SAF disc brake axle, with 430 mm disc diameter, Air suspension with lifting & lowering valve, with holding function for H&S Wheels and tires 385 / 65 R 22,5 from leading manufacturers Factory silver steel rims Brake system 2-line compressed air brake system Spring-applied parking brake 2 interchangeable clutch heads at the front, without connecting cable EBS, electronic brake system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin interchangeable sockets at the front, without connecting cable Approval / plates Country of registration: Germany with Dekra approval and certificate (according to §13 EG - FGV) Prepared for single-line license plate holder Contour markings with reflective strips to ECE R 048, white at the sides and red at the rear Warning sign according to ECE - 70 Paint finish Frame DB nova gray Support legs coated black Attention: Archive pictures!

Condition: used, machine/vehicle number: 9c9dadcd470a127e08914041a, empty load weight: 2,600 kg, maximum load weight: 10,800 kg, overall weight: 13,400 kg, axle configuration: 2 axles, first registration: 05/2017, tire size: 285/70 r19,5, Year of construction: 2017, Further information Fine-grained steel welded construction, fifth wheel coupling, make of our choice for 2\ kingpin, telescopic support foot, wheel chocks with holder, steel underride guard, half-shell mudguards, removable upper parts Towbar with tested 50 mm towing eye, under-coupler towbar BPW disc brake axles, air suspension with lift & lower valve, mechanical dolly steering system (required in Germany to comply with the BO circle) 2-line compressed air brake system, spring-loaded parking brake, Duomatic coupling head at the front, with connecting lines to the tractor unit, Duomatic coupling head to the trailer, incl. connecting coil, EBS, electronic brake system with EBS plug at the front, with connecting cableEBS connecting cable to the trailer, with CAN router, axle load detection for trucks via EBS, without truck instal. Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! 24 volt, multi-chamber lights, amber LED lighting at the side, 2 white position lights at the front, 2 white/red lane departure lights at the rear, 1 x 15-pin plug at the front, with connecting cable to the truck 1 x 15-pin socket, with connecting spiral to the semi-trailer, cable for reversing camera system with socket with Dekra approval, prepared for single-line license plate holder, contour marking with reflective strips to ECE R 048, white at the sides and red at the rear, warning sign to ECE - 70 Saddle height approx.: 960 mm Rjdpfxei Rivto Ahzel

Condition: new, machine/vehicle number: 6d88bda3a1ee2464a81b34f36, empty load weight: 4 kg, maximum load weight: 13 kg, overall weight: 18 kg, axle configuration: 2 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction, with slight pretensioning in the middle, turntable with strong ball bearing slewing ring, wheel chocks with holder, quarter-shell mudguards in front of and behind each axle Low loader lashing eyes over front axle: 2 pairs of ring lashing eyes, 5 tons each at the front on offset Lowbed: 4 pairs of lashing eyes on the side of the low bed, 6 tons each 5 pairs of lashing eyes per 5 tons between the side members Trailer drawbar Turntable Drawbar with tested 40 mm drawbar eye, mechanically adjustable in length by 6 x 100 mm and lockable (drawbar length 1 700 - 2 300 mm) Axles + suspension BPW drum brake axles, each with an axle load of 10 tons, axle adjuster. Axle endurance brake test to 105 km/h, rear axle can be removed manually. By releasing the air lock and lowering the rear to the ground. Then disconnect the connecting hoses from the rear section, insert the transport bar into one of the rear sockets and unhook the rear by gently pushing it down at the rear and pulling it back at the same time (parking brake released). After loading or unloading, drive up to the rear section and hook it in up to the mark. Then lift the rear section up to driving height and attach the connecting hoses. Confirm the pin lock. (Visually check whether the bolt engages) and check the rear function. Air suspension with lift & lower valve Wheels and tires 235 / 75 R 17.5, from leading manufacturers, steel rims in twin arrangement, factory silver Brake system 2-line compressed air brake system, spring-loaded parking brake, 2 interchangeable clutch heads at the front, with connecting lines to the motor vehicle, EBS, electronic brake system with EBS plug at the front, with connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side, 2 white position lights at the front, 2 white/red lane departure lights at the rear, rotating beacon with holder, switched via parking light (light can be removed), 2 pairs of warning signs, double LED illuminated and extendable to 3,300 mm, removable with plug, 2 x 7-pin interchangeable plugs at the front, with connecting cable, 1 x 7-pin agricultural plug, voltage converter 12/24 volt (only for electrics, not for ABS/EBS) Floor Steel/ checker plate floor on offset, between longitudinal and cross member with perforated plate cover. Axle cover cannot be driven over, widening to 3000 or 3300 mm possible. Redpfx Ahsi Ri N Aozjl Operating instructions Please note! A special permit is required for axle loads of 10,000 kg. The permit must be applied for individually in each federal state; the legislator does not have to give an approval for 20 tons GG. Customer risk. Special approval required if the overall length of the train exceeds 18 750 mm. Observe country-specific approval regulations. The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. Observe the BO circle!!! Approval / plates Country of registration: Germany, with Dekra approval and expert opinion (according to §13 EG - FGV), prepared for single-line license plate holder, warning sign according to ECE - 70, contour marking with reflective strips according to ECE R 048 Paintwork Front frame hot-dip galvanized incl. passivation, rear frame RAL9006 silver, drawbar KTL bla

Condition: new, machine/vehicle number: efdaf8862775f9506d97b86a5, empty load weight: 5,600 kg, maximum load weight: 29,400 kg, overall weight: 35,000 kg, axle configuration: 3 axles, tire size: 385/65 r22,5², Further information Redpfei Ri Ihjx Ahzsl Chassis tipper semi-trailer Fine-grained steel welded construction, lightweight design, fifth wheel plate with interchangeable 2 kingpins Curved front end Patented 24 t. 2-speed support winch, single-side operation, with straight lower section, without thrust compensation 2 wheel chocks with holder Underride guard, folding Half-shell mudguards Integrated mudguard holder Stone-repellent surface With anti-spray flaps on last axle only 1 tarpaulin pole with bracket 2 towing hooks at the rear Axles+suspension SAF disc brake axles with 430 mm disc diameter Axle/chassis laser-measured Reduction in tire wear and fuel consumption Axles in off-road version, Air suspension 1st axle automatic lift axle, including forced lowering and starting aid, actuation of 3x brakes (starting aid is functional up to an axle load excess of 30% and up to a speed of max. 25 km/h) Hot-dip galvanized lift axle mechanism 10-year warranty against rusting through Brake system 2-line compressed air brake systemColor-coded cable routing for easy servicing. Spring-loaded parking brake 2 interchangeable front clutch heads, without connecting line EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve Vehicle stability system Wheels and tires 385/65 R22.5 tires of the manufacturer's choice Steel rims, factory silver Electrical system 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable sockets at the front, without connecting cable Hydraulics Low-pressure cylinder max. 170 bar, smallest stage hard-chlorinated, with HDK screw socket, fixed part, NW 48 mm (without hose connection). Hydraulic actuation via truck power take-off Troughs Aluminum box body made of high-quality, abrasion-resistant 5 mm thick front wall, with external walls made of 30 mm hollow chamber profiles, cleanly welded, with bulk material-repellent top rail profile. Inside with access to front wall (not in conjunction with Cramaro). Shovel and brush holder on the outside of the front wall. Greenline - conical and aerodynamic trough shape Membrane rear wall Rear wall pendulum-mounted with double-joint hinge and with 2-leaf door partition 1/2 to 1/2, with pivoting gallows at the top, with one grain slider per door. Rear panel with rubber sealNote! Heat-resistant up to max. 170°C! Floor 6 mm thick throughout Standing platform with access, connection plate for air/electric and brake with large clearance for best possible operability. Roller tarpaulin on one side for depositing in FR-right, with central locking in FR-left Operating instructions For salt, lime, etc. We recommend a tipping cylinder with a hard chrome-plated piston rod so that it is not attacked by the material and rusts. The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Germany Test approval according to EC 2007/46 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips according to ECE R 048, white on the sides and red on the rear Paint finish Frame DB 7350 Novagr

Condition: new, machine/vehicle number: d73a4869e108da5fdd6e55526, empty load weight: 4 kg, maximum load weight: 33 kg, overall weight: 38 kg, axle configuration: 3 axles, tire size: 385/55 r22.5, Further information Chassis Saddle Container Welded fine-grained steel construction, saddle plate with interchangeable 2 kingpins and 2 kingpin positions Container mountings: Rear extension retracted: 1 x 20 feet or 1 x 30 feet Rear flush Center telescope 1st stage, rear extension extended 1st stage: 2 x 20 feet or 1 x 40 feet with and without gooseneck tunnel Center telescope 2nd stage, rear extension extended 2nd stage 1 x 45 feet with gooseneck tunnel and overloaded to the rear Center telescope 2nd stage, front extension extended 1st stage Rear extension extended 2nd stage 1 x 45 feet with long gooseneck tunnel and chamfered corners Center telescope as an interlocking central tubular frame with bolt lock without height adjustment at the rear and without folding center supports, no transport of containers without tunnel possible. 2 container guides, incl. connection plate for electrical, air and brake connections (connections positioned upwards) Plug-in adapter for front locking, for locking the containers without tunnel from below, with holder when not in use Front extension mounted on castors, can be pulled out manually (for 45 containers with long tunnel) Rear extension mounted on rollers, with hand crank 24 t. 2-speed support winch, single-sided operation, with straight lower section, without thrust compensation 2 wheel chocks with holder Aluminium side bumper Galvanized steel underride guard Extendable underride guard for 45 foot containers Half-shell mudguards with anti-spray flaps according to EG Impact protection at the rear Axles+suspension SAF disc brake axles with 430 mm disc diameter Axle/chassis laser-measured Reduction in tire wear and fuel consumption Rjdpfxji Ri E Aj Ahzel Axle spacing offset mm (combined transport) up to 44 tons gross train weight Air suspension 1st axle automatic lift axle, including forced lowering and starting aid, actuation of 3x brakes (starting aid is functional up to an axle load excess of 30% and up to a speed of max. 25 km/h) Brake system 2-line compressed air brake systemColor-coded cable routing for easy servicing. Spring-loaded parking brake Tele Control Axle relief for easy telescoping 2 swap-proof coupling heads at the front, without connecting cable EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve Vehicle stability system Axle load detection via EBS-Canbus signal, for indication via display in the cab, truck must be prepared accordingly, no truck installation (no calibrated scales) Wheels and tires 385/55 R22.5 make of the manufacturer's choice Steel rims, factory silver Electrical system 24 volt, 4 x 3 chamber lights + 1 round reversing light and + 1 round rear fog light, amber LED lighting at the side 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable sockets at the front, without connecting cable Operating instructions When transporting 45 containers with a short tunnel, with or without front extension, the permissible system length from the kingpin to the rear edge of the vehicle and the total train length of 16500 mm is exceeded! The underride guard must be extended manually! A special permit in accordance with § 70 StVZo is required! Approval / plates Germany Test approval according to EG 2007/46 24/7 service hotline Prepared for single-line license plate holder Warning sign according

Condition: new, machine/vehicle number: 0fe2184cda24503447c582a1e, empty load weight: 3 kg, maximum load weight: 34 kg, overall weight: 38 kg, axle configuration: 3 axles, tire size: 385/55 r 22,5, Further information Chassis semi-trailer container Fine-grained steel welded construction, saddle plate with replaceable 2 kingpins Container mounts:1 x 40 feet with gooseneck tunnel The transportation of filled tank containers is excluded. Without rear height adjustment and without folding center supports, no transport of containers without tunnel possible. Container guide front plug-in 24 t. 2-speed support winch, single-sided operation, with straight lower section, without thrust compensation Wheel chocks with holder Aluminium side bumper Galvanized steel underride guard Half-shell mudguards with anti-spray flaps according to EG Impact protection at the rear Axles+suspension SAF disc brake axles with 430 mm disc diameter Axle/chassis laser-measured Reduction in tire wear and fuel consumption Axle spacing offset mm (combined transport) up to 44 tons gross train weight Air suspension 1st axle automatic lift axle, including forced lowering and starting aid, actuation of 3x brakes (starting aid is functional up to an axle load excess of 30% and up to a speed of max. 25 km/h) Brake system 2-line compressed air brake systemColor-coded cable routing for easy servicing. Spring-loaded parking brake 2 interchangeable clutch heads at the front, without connecting line EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve Vehicle stability system Axle load detection via EBS-Canbus signal, for indication via display in the cab, truck must be prepared accordingly, no truck installation (no calibrated scales) Wheels and tires 385/55 R22.5 make of the manufacturer's choice Steel rims, factory silver Electrical system 24 volt, multi-chamber lights, rear and brake lights in LED, amber LED lighting on the side (Note! with certain towing vehicles, misdiagnosis may occur although the function is given) 2 white position lights at the front 2 white/red rear lane departure lights 1 x 15-pin socket at the front, without connecting cable LED work lights on both sides (switched via reversing light) Additional LED work light(s) at the rear, switched via reversing light Operating instructions The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to incorrect load distribution) Special approval required if the overall length of the train exceeds 16,500 mm. Attention: Transport of filled tank containers is excluded! Country of approval / plates Germany with Dekra approval and expert opinion (according to §13 EG - FGV) Prepared for single-line license plate holder Warning sign according to ECE - 70 Contour markings with reflective strips to ECE R 048, white at the sides and red at the rear Paint finish Rjdpfx Aei Ri Ayehzsl Frame DB 7350 nova gray10-year warranty against rusting through Support legs coated black Without pallet box Paint Attention: Archive pictures!

Condition: new, machine/vehicle number: 1f4581c873ed977cb9602039b, empty load weight: 3 kg, maximum load weight: 34 kg, overall weight: 38 kg, axle configuration: 3 axles, tire size: 385/65 r22.5, Further information Chassis semi-trailer container Fine-grained steel welded construction, saddle plate with replaceable 2 kingpins Container mounts: 1 x 20 foot centered (or swap body container 7.15 / 7.45), not retractable at the front, the pivot pins of the container lock in the longer version 24 to. 2-speed support winch, single-side operation, with straight lower section, without thrust compensation 2 wheel chocks with holder Side collision protection Aluminum underride guard Half-shell mudguards with anti-spray flaps according to EG VA drip tray with 1 1/4 inch drain pipe + 1 1/4 inch stopcock, incl. drip tray, with perforated tread plates, approx. 400 mm wide, left + right between drip tray and side member 4 hose trays approx. 4500 mm long (hose box) for hose pipes 2 x DN 200 outside + 2 x DN 160 centrally arranged, rear hose box (stainless steel) 300 mm deep, splash-proof, cover (stainless steel) with rubber seal all round, with drain hole at lowest point, then without cover on hose pipes 1 stainless steel earthing lug at the rear in FR on the right of the frame, with international earthing sticker on the frame, Steps at the rear right on the underride guard, at the rear in FR right on the outside of the main beam, tread plate approx. 260 mm long and 300 mm wide, Axles + suspension SAF disc brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Axle spacing offset mm (combined transport) up to 44 tons gross train weight Air suspension 1st axle automatic lift axle, including forced lowering and starting aid, actuation of 3x brakes (starting aid is functional up to an axle load excess of 30% and up to a speed of max. 25 km/h) Brake system 2-line compressed air brake system Colored cable routing for easy servicing Spring-loaded parking brake 2 swap-proof coupling heads at the front, without connecting line EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve Vehicle stability system Axle load detection via EBS-Canbus signal, for indication via display in the cab, truck must be prepared accordingly, no truck installation (no calibrated scales) Wheels and tires 385/65 R22.5 make of the manufacturer's choice Steel rims, factory silver Electrical system 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white position lights at the front 2 white/red rear lane departure lights 1 x 15-pin socket at the front, without connecting cable Operating instructions The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to incorrect load distribution) This vehicle may only be loaded with 20' tank containers that comply with ISO 668 and in particular ISO 1496-3! The tank containers must have "end-load-transfer areas"! Country of approval / plates Germany Test approval according to EC 2007/46 24/7 service hotline Prepared for single-line license plate holder Warning sign according to ECE - 70 Approval according to ADR acc. to 9.1.1.2 of ADR, EX/II, EX/III / certificate of approval for vehicles for the transport of certain dangerous goods (ex.B3) with warning sign at the rear, not valid for substances according to UN 0331 and 0332 (explosives B-E) Contour marking with refle Rjdpfxoi Rixks Ahzjl

Condition: new, machine/vehicle number: 2b58968e34fac93b429a256e9, empty load weight: 5 kg, maximum load weight: 12 kg, overall weight: 18 kg, axle configuration: 2 axles, tire size: 235 / 75 r 17,5, Further information Rodji Ri Nxspfx Ahzel Chassis low loader trailer Welded steel construction Turntable with strong ball bearing slewing ring, storage box embedded in turntable front end Folding rear support Wheel chocks with holder Aluminum side bumpers Rear spray flaps across the entire width Quarter-shell mudguards in front of 1st axle Spare wheel holder for 1 electric wheel, with wheel mounting kit Spare wheel, same make as basic tires, steel rim Plastic tool box, with shelf, w=620/h=360/t=440 mm, lockable with a padlock. (lock not included in scope of delivery) Low loader lashing eyes 3 pairs of lashing points, each 10 tons, integrated in the floor at the front 6 pairs of lashing mushrooms at the top and sides, each 10 tons, embedded in the outer frame 1 x according to the rest of the neck area, distributed between them, spacing not greater than 1200 mm 1 x rear bevel 5 pairs of ring lashing eyes embedded in the outer frame, 5 tons each (can be converted to stake pockets) Trailer drawbar Turntable Drawbar with tested 40 mm drawbar eye Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction of tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings Wheels and tires 235 / 75 R 17,5 at the manufacturer's choice Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 non-interchangeable clutch heads at the front, with connecting cables to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cableVoltage converter for 12/24 volt operationNote! A 7-pin 12 volt socket is required on the tractor/tractor! (Required in conjunction with electrical voltage converter!) Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrical system 24 volt, multi-chamber lights, amber LED lighting on the side 2 white/red rear lane departure lights 2 white position lights at the front Additional LED work light(s) at the rear, switched via reversing light 2 x 7-pin interchangeable plugs at the front, with connecting cable1 x 7-pin agricultural plugVoltage converter 12/24 volt (only for electrics, not for ABS/EBS) Floor Front area steel floor, then with 70 mm softwood floor, steel/ checker plate flooring in the wheel housing area Rear slope with 70 mm softwood floor Low loading area incl. rear slope 8 200 mm Drive-on ramps Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways covered with wood with spring lift support Operating instructions A special permit is required for axle loads of 10,000 kg. The permit must be applied for individually in each federal state; the legislator does not have to give an approval for 20 t GG. Customer risk. Country of registration / plates Country of registration: Germany with Dekra approval and expert opinion (according to §13 EG - FGV) 24/7 service hotline Prepared for two-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white on the sides and red on the rear Paint finish Frame DB 7350 nova gray10-year warranty against rusting through Drawbar Galvanized or black, manufacturer's choice Drive-on ramps Hot-dip galvanized Attention: Archive pictures!

Condition: new, machine/vehicle number: 45d76d32267904923b7adcdea, empty load weight: 4,980 kg, maximum load weight: 30,020 kg, overall weight: 35,000 kg, axle configuration: 3 axles, tire size: 385/65 r22.5, Further information Chassis tipper semi-trailer Fine-grained steel welded construction, lightweight design, fifth wheel plate with interchangeable 2 kingpins Curved front end Patented 24 t. 2-speed support winch, single-side operation, with straight lower section, without thrust compensation Wheel chocks with holder Underride guard, folding Half-shell mudguards Integrated mudguard holder Surface stone-repellent Tow hook at the rear Axles+suspension SAF disc brake axles Axle/chassis laser-measured Reduction of tire wear and fuel consumption Air suspension 1st axle automatic lift axle, including forced lowering and starting aid, actuation of 3x brakes (starting aid is functional up to an axle load excess of 30% and up to a speed of max. 25 km/h) Hot-dip galvanized lift axle mechanism 10-year warranty against rusting through Brake system 2-line compressed air brake systemColor-coded cable routing for easy servicing. Spring-loaded parking brake 2 interchangeable front clutch heads, without connecting line EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve Vehicle stability system Wheels and tires 385/65 R22.5 tires of the manufacturer's choice Polished aluminum rims, manufacturer's choice Electrical system 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin socket at the front, without connecting cable Hydraulics Low-pressure cylinder max. 170 bar, smallest stage hard-chlorinated, with HDK screw socket, fixed part, NW 48 mm (without hose connection). Hydraulic actuation via truck power take-off Troughs Aluminum box body made of high-quality, abrasion-resistant 5 mm thick front wall, with external walls made of 30 mm hollow chamber profiles, cleanly welded, with bulk material-repellent top rail profile. Inside with access to front wall (not in conjunction with Cramaro). Shovel and brush holder on the outside of the front wall. Greenline - conical and aerodynamic trough shape Membrane rear wall Rear wall as swing flap with double-jointed hinge, resting on the outside with double hook lock. Rear panel with rubber sealNote! Heat-resistant up to max. 170°C! Floor 5 mm thick throughout, Brinell 110Note! Only for transporting sand, grit and rolled gravel with a maximum grain size of up to 20 mm! All other transport goods are excluded from the warranty! Standing platform with step, connection plate for air/electric and brake with large clearance for best possible operability. Roller tarpaulin on one side for depositing in FR-right, with central locking in FR-left Operating instructions For salt, lime, etc. We recommend a tipping cylinder with a hard chrome-plated piston rod so that it is not attacked by the material and rusts. The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and castering behavior possible due to incorrect load distribution) Rsdpei Ri Idefx Ahzjl Revolution Link: Revolution Link experience report: Country of registration / plates Germany with Dekra approval and expert opinion (according to §13 EG - FGV) 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips according to ECE R 0

Condition: new, machine/vehicle number: cf997e3303ed59631e2030c1b, overall weight: 38,000 kg, axle configuration: 3 axles, tire size: 385/55 r22,5, Further information Chassis Saddle Container Fine-grained steel welded construction, saddle plate with interchangeable 2 kingpins and 2 kingpin positions Container mountings: Rear extension retracted: 1 x 20 feet or 1 x 30 feet Rear flush Center telescope 1st stage, rear extension extended 1st stage: 2 x 20 feet or 1 x 40 feet with and without gooseneck tunnel Center telescope 2nd stage, rear extension extended 2nd stage: 1x45 feet with and without gooseneck tunnel and overloaded to the rear. Center telescope as an interlocking central tubular frame with bolt lock With rear height adjustment and folding center supports for containers without tunnel Container guide at the front Plug-in and removable (electrical, air and brake connections at the front of the front cross member) Plug-in adapter for front locking, for locking the containers without tunnel from below, with holder when not in use Rear extension mounted on rollers, with hand crank 24 t. 2-speed support winch, single-sided operation, with semicircular lower section and straight connecting plate, with thrust compensation 2 wheel chocks with holder Aluminium side bumper Galvanized steel underride guard Extendable underride guard for 45 foot containers Half-shell mudguards with anti-spray flaps according to EG Impact protection at the rear Axles+suspension SAF disc brake axles with 430 mm disc diameter Axle/chassis laser-measured Reduction in tire wear and fuel consumption Axle spacing offset mm (combined transport) up to 44 tons gross train weight Air suspension Brake system 2-line compressed air brake system Colored line routing for easy service. Spring-loaded parking brake Tele Control Axle relief for easy telescoping 2 swap-proof coupling heads at the front, without connecting cable EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve Vehicle stability system Axle load detection via EBS-Canbus signal, for indication via display in the cab, truck must be prepared accordingly, no truck installation (no calibrated scales) Wheels and tires 385/55 R22.5 make of the manufacturer's choice Steel rims, factory silver Rsdji Ri Exepfx Ahzol Electrical system 24 volt, multi-chamber lights, rear and brake lights in LED, amber LED lighting on the side (note! with certain towing vehicles, misdiagnosis can occur although the function is given) 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable sockets at the front, without connecting cable Operating instructions Attention: Transport of filled tank containers is excluded! When transporting 45 containers with a short tunnel, with or without front extension, the permissible system length from the kingpin to the rear edge of the vehicle and the total train length of 16500 mm is exceeded! The underride guard must be extended manually! A special permit in accordance with § 70 StVZo is required! Country of registration / plates Germany Test approval according to EG 2007/46 24/7 service hotline Prepared for single-line license plate holder Warning sign according to ECE - 70 Contour markings with reflective strips to ECE R 048, white at the sides and red at the rear Paintwork Frame front section + rear extension hot-dip galvanized Rear section DB 7350 nova gray 10-year warranty against rusting through Support legs coated black ATTENTION: Archive pictures

Condition: new, machine/vehicle number: a203d9a559ff6484cf2a14c1f, empty load weight: 4 kg, maximum load weight: 33 kg, overall weight: 38 kg, axle configuration: 3 axles, tire size: 385/65 r22.5, Further information Chassis Saddle Container Welded fine-grained steel construction, fifth-wheel plate with replaceable 2 kingpins and 2 kingpin positions Front locking on tipping ram support frame with guide wedges on both sides, rear locking on continuous pivot shaft with return spring Without subframe for self-supporting containers Container mounts: Locking cross member, 2-fold for locking 1 x 20 foot or 1 x 30 foot container. (Note! low fifth wheel load for 20 foot containers) Adjustment via central telescope as an interlocking central tubular frame with pin lock. 24 t. 2-speed support winch, single-side operation, with straight lower section, without thrust compensation Redpsi Ri Avefx Ahzol Free support foot corner dimension or free swing radius to the rear approx. 1850 mm 2 wheel chocks with holder Half-shell mudguard with anti-spray flaps according to EG Hydraulics Low-pressure cylinder max. 170 bar, smallest stage hard-chlorinated, with HDK screw socket, fixed part, NW 48 mm. (without hose connection) Hydraulic actuation via truck power take-off Hydraulic connection with hose and HDK screw plug NW = 48 mm with knurled nut Axles + suspension SAF disc brake axles with 430 mm disc diameter Axle/chassis laser-measured Reduction in tire wear and fuel consumption Axle spacing offset mm (combined transport) up to 44 tons gross train weight Air suspension Brake system 2-line compressed air brake system Colored line routing for easy service. Spring-loaded parking brake Tele Control Axle relief for easy telescoping 2 swap-proof coupling heads at the front, without connecting cable EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve Vehicle stability system Axle load detection via EBS-Canbus signal, for indication via display in the cab, truck must be prepared accordingly, no truck installation (no calibrated scales) Wheels and tires 385/65 R22.5 Manufacturer's choice Steel rims, factory silver Incl. Electrics 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable sockets at the front, without connecting cable Additional LED work light(s) at the rear, switched via reversing light Country of registration / plates Germany Test approval according to EC 2007/46 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips according to ECE R 048, white on the sides and red on the rear Paint finish Frame DB 7350 nova gray 10-year warranty against rusting through Support legs coated black Attention: Archive pictures!

Condition: new, machine/vehicle number: 2dff0c136c85096f36822a0bb, empty load weight: 7,150 kg, maximum load weight: 16,850 kg, overall weight: 24,000 kg, axle configuration: 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction Turntable with strong ball bearing slewing ring, storage box embedded in turntable front end Folding rear support 2 wheel chocks with holder Aluminum side collision protection Rear spray flaps across the entire width Widenings can be extended to 3,000 mm (not in the rear slope) (However, the track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Storage compartment for wooden planks in the middle of the cargo bed Wooden planks 70 mm for widening to 3000 mm Low loader lashing eyes 3 pairs of lashing points each 10 to integrated in the floor at the front 6 pairs of lashing points at the top and sides, each 10 tons, integrated in the outer frame 1 x to the neck area remaining distributed in between Spacing not greater than 1200 mm 1 x rear slope 5 pairs of stake pockets embedded in the outer frame, inside 70 x 40 mm, (can be converted to 5 to. ring lashing eyes, not included in the scope of delivery) Towing equipment Trailer turntable Drawbar with tested 40 mm drawbar eye Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation axle load compensation (rocker compensation) Brake system 2-line compressed air brake system Colored line routing for easy servicing. Spring-loaded parking brake Incl. 2 swap-proof coupling heads at the front, with connecting lines to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable, Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Wheels and tires 235 / 75 R 17,5 at the choice of the manufacturer Steel rims in twin arrangement, factory silver Electrical system 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin interchangeable plugs at the front, with connecting cable, 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Front area steel floor, then with 70 mm softwood floor, steel/checker plate flooring in the wheel housing area Rear slope with 70 mm softwood floor Deep loading area incl. rear slope 8,200 mm Drive-on ramps Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways Covered with wood Incl. with spring lift support Operating instructions With an axle load of 10,000 kg, a special permit is required, only indivisible loads possible!!! The specified total weight is technically possible; depending on the load, the total weight may not be achieved while complying with the permissible axle/support and fifth-wheel loads. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Country of registration: Germany with Dekra approval and expert opinion (according to §13 EG - FGV) 24/7 service hotline Prepared for two-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white on the sides and red on the rear Paint finish Frame DB 7350 nova gray 10-year warranty against rusting through Drawbar Galvanized or black, Redpfx Aji Riy Eohzol at the manufacturer's choice Drive-on ramps Hot-dip galvanized Attention: Archive pictures!

Condition: used, machine/vehicle number: 816b3dfbfa1c7d49b7d052bd6, empty load weight: 2,500 kg, maximum load weight: 8,000 kg, overall weight: 10,500 kg, axle configuration: 2 axles, first registration: 07/2022, tire size: 235/75 r17,5, Year of construction: 2022, Further information Chassis central axle trailer low bed Welded fine-grained steel construction, front gear support foot, telescopic rear support, wheel chocks with bracket, sheet steel mudguards over both wheels Towing device central axle trailer Drawbar with tested 40 mm towing eye, height-adjustable drawbar via spindle, max. adjustment range 250 mm Rjdpfx Ahjqmc Raezol Axles + suspension Euro axles of our choice, with angular roller bearings and S-cam brakes, laser-measured axle/chassis to reduce tire wear and fuel consumption, parabolic suspension with maintenance-free steel/rubber bearings and mechanical axle load compensation (rocker compensation) Brake system 2-line compressed air brake system, spring-loaded parking brake, 2 interchangeable coupling heads at the front, with connecting lines to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side, 2 white position lights at the front, 2 white/red lane departure warning lights at the rear, 1 x 15-pin plug at the front, with connecting cable, TTS bridge low-lying steel trough, bridge floor made of steel/checker plate covering, steel walls solidly welded to floor, bridge length 5500 mm, trough at front and sides with load-lock profile for tensioning strap attachment (8 pieces at front, 16 pieces on each side) Note: Slight floor undulation possible due to welding distortion! Pair of lashing eyes, 1 x at the front in the corners of the steel tray and 1 x at the rear in the floor, 5 tons each. Pair of additional lashing eyes in the floor, 5 tons each Drive-on ramps Steel ramps 2 300 mm long, 510 mm wide, can be moved sideways, with handle on the ramps, covered with wood, with gas pressure jack for one-man operation Operating instructions The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Country of registration: Germany, with Dekra approval and expert opinion (in accordance with §13 EG - FGV), prepared for single-line license plate holder, contour marking with reflective strips in accordance with ECE R 048, white at the sides and red at the rear

Condition: new, machine/vehicle number: 8df1ead53cc82aeb51e50a37d, empty load weight: 4 kg, maximum load weight: 13,880 kg, overall weight: 18 kg, axle configuration: 2 axles, tire size: 235 / 75 r 17,5, Further information Chassis Turntable Disposal Fine-grained steel welded construction Container locking system: - 2 pairs of locking hooks embedded in the floor - Pneumatic actuation The container locking mechanism is a 2-point design, acting from the inside, and locking of roll-off containers with an inner web is not possible (for transporting roll-off containers with a sub-frame in accordance with DIN 30722) Note! At the start of the roller recess at the front, the container must be pushed on completely flat! Longitudinal guide rails can be moved sideways and removed, rails approx. 115 mm high Turntable with strong ball bearing slewing ring 8 pairs of lashing mushrooms at the top and sides of the outer frame, 5 tons each 7 pairs of stake pockets embedded in the outer frame, inside 70 x 40 mm, (can be converted to 5 to. ring lashing eyes, not included) 2 wheel chocks with holder Aluminum side bumpers Steel underride guard Quarter-shell mudguards according to EG with anti-spray flaps according to EG Towing equipment Trailer turntable Drawbar with tested 40 mm drawbar eye Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction of tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings Wheels and tires 235 / 75 R 17,5 at the manufacturer's choice Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 non-interchangeable coupling heads at the front, with connecting cables to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front Redpji Ri Nuefx Ahzol 2 white/red lane departure lights at the rear 2 x 7-pin interchangeable plugs at the front, with connecting cable, floor Steel floor Roller recess for container recessed in the floor at the frontfor roll-off containers from 5,000 - 7,000 mm in length Note: Slight floor undulation possible due to welding distortion! Drive-on ramps Lockable storage space for loading ramps underneath the loading area Operating instructions A special permit is required for axle loads of 10,000 kg. Approval must be applied for individually in each federal state; the legislator does not have to grant approval for 20 t GG. Customer risk. The specified total weight is technically possible; depending on the load, the total weight may not be achieved while complying with the permissible axle/support and fifth-wheel loads. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Country of registration: Germany with Dekra approval and expert opinion (according to §13 EG - FGV) 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white at the sides and red at the rear Warning sign according to ECE - 70 Paint finish Frame DB 7350 nova gray 15-year warranty against rusting through Note: Bottom corrugation possible due to hot-dip galvanizing! Drawbar KTL black Attention: Archive pictures!