Used Fliegl Semitrailers With Swap Body for sale (345)

Condition: new, maximum load weight: 29,500 kg, overall weight: 35,000 kg, axle configuration: 3 axles, loading space length: 7,200 mm, loading space width: 2,350 mm, loading space height: 1,450 mm, loading space volume: 25 m³, total width: 2,550 mm, Vehicle is from ongoing production – available in approx. 2 weeks Vehicle / Body: Tipper body Gross weight: 35,000kg / 39,000kg Tare weight: 5,500kg!!! Payload: 29,500kg / 33,500kg Overall length: 8,600mm Volume: 25 cbm Further Information: - Overall height approx. 3,160mm - Internal width approx. 2,350mm - Fifth wheel height approx. 1,200mm Chassis Semi-Trailer Tipper: - Fine-grain steel welded construction, in basic lightweight design - 1x central landing gear leg Lasdpfxovhyf Ro Aldsc - Retractable underrun protection - Underrun protection with “spring assist” for easier operation - Half-shell mudguards - Integrated "mudguard bracket" with stone-repellent surface - With anti-spray mudflaps only on the last axle - 2 towing hooks at the rear Axles & Suspension: - SAF disc brake axles with 430 mm disc diameter - "Axle/chassis laser alignment" for reduced tire wear and lower fuel consumption - Axles in off-road specification - Air suspension - Air bag pressure gauge, mounted at the front on curved chassis - 1st axle with automatic lift axle, additionally controllable electrically from the truck, including forced lowering and start-up aid, no truck installation required (Start-up aid function up to 30% axle overload and up to a speed of max. 25 km/h) Braking System: - 2-line compressed air braking system Color-coded line routing for easier service. - Spring-loaded parking brake - 2 foolproof coupling heads at the front, without connecting line - 24 Volt EBS, electronic braking system with EBS socket at the front, without connecting cable - With lift & lower valve - Vehicle stability control system - Automatic tipping lowering with shut-off valve Wheels and Tyres: - 6 x 385/65 R22.5” European brand, manufacturer’s choice Electrics: - 24 Volt, multi-chamber LED lights, side yellow LED lighting, LED license plate lighting (Note: Some towing vehicles may display fault codes despite full functionality) - Side yellow LED lighting linked to indicator "flashing side marker lights" - Premium LED side marker lights, each with 20 LEDs per light - 2 white front position lights, LED included - 2 white/red lane position lights at the rear, LED included - 2 x 7-pin and 1 x 15-pin foolproof sockets at the front, without connecting cable - LED work lights both sides (switched via reversing light) - 2 additional LED work lights, recessed at rear Hydraulics: - High-pressure cylinder max. 250 bar, smallest stage hard chrome-plated, with HDK screw coupling, fixed section, NW 48 mm - Manufacturer Hyva - Operation hydraulic via truck PTO - Hydraulic connection with hose and vehicle screw connector NW = 54 mm with large wing nut Body: HARDOX steel round tipper body in "Stone Master Design" made of highly wear-resistant HB 400/450 steel. Sloped front wall with external hydraulic cylinder mount. Interior with access at front wall. - Greenline – conical and aerodynamic body design - External shovel and broom holder at front wall - "Membrane" rear wall - Rear wall as pendulum tailgate with "double joint hinge", external, with dual hook locking. 2 clamping screws with toggle locks at lower side - Rear wall with rubber seal Note: Heat resistant up to max. 170°C! - Side walls continuously 4 mm thick, floor 4/5 mm thick, wear and weight-optimized construction - Fliegl S.T.E.P. – swiveling standing platform at the front with foldable access ladder for side entry front left

Condition: new, maximum load weight: 23,920 kg, overall weight: 30,000 kg, axle configuration: 3 axles, NEW VEHICLE Fliegl 3 axle low loader type DTS 300, hot-dip galvanized Total weight 24,000 kg / 30,000 kg Payload 17,920 kg / 23,920 kg Empty weight 6,080 kg Total length 10,900 mm Loading length 8,680 mm Loading bed 6,500 mm including 900 mm approach slope Parabolic suspension Long ramps 2,800 mm with hydraulic operation Wider widths to 3,000 mm with warning signs and rotating beacon Large lashing package with 5.0 and 10.0 ton lashing points 5 pairs of stake pockets Lodpfoxb Nmyox Aldjac Towing eye 40 mm Plus pre-freight / provision from the Wiesmoor storage location 1,280.00 €/ Net Rent-to-own offer: term 48 months, residual value 40%, down payment only VAT. Monthly rate: EUR 500.00

Condition: new, maximum load weight: 17,900 kg, overall weight: 24,000 kg, axle configuration: 3 axles, loading space length: 8,670 mm, loading space width: 2,500 mm, loading space height: 860 mm, total width: 2,520 mm, From ongoing production Total weight: 24,000kg/ 30,000kg Empty weight: 6,100kg Payload: 17,900kg/ 23,900kg Total length: 10,890mm Loading length: 8,670mm total, 2,520mm offset, 6,500mm loading bed Width: 2,520mm Loading height: 860mm Further information Steel welded construction Turntable with strong ball bearing ring Foldable rear support Wheel chocks with holder Aluminum side impact protection Rear mud flaps across the entire width (not in conjunction with forklift bracket) Half-shell mudguard 1st axle with anti-spray mud flaps Anti-spray mud flaps behind 2nd and 3rd axles Plastic tool box Extendable extensions to 3,000mm Storage compartment for wooden planks in the middle of the loading area Wooden planks 70 mm for widening to 3,000 mm Lashing eyes for low loader 1 pair of lashing cutouts in the longitudinal beam at the front on the offset, 10 tons each. 4 pairs of lashing holes in the outer frame of the crank, each with 5 tons (tension belt attachment) 7 pairs of lashing mushrooms embedded in the outer frame at the top and side, each with 10 tons 1 x at the front on the crank, 6 x in the low bed Pair of ring lashing eyes embedded in the outer frame, each with 5 tons (can be converted to stake pockets) Pair of additional folding lashing eyes, each with 10 tons 1 x on the crank 1 x embedded in the floor behind the last axle Trailer towing device, turntable Draw fork with tested 40 mm drawbar eye Draw fork height adjustment via spring Axles + suspension Drum brake axles, at the manufacturer's discretion "Axles/chassis laser-measured" Reduction in tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation (rocker compensation) Wheels and tires 235 / 75 R 17.5" at the manufacturer's choice steel rims in twin arrangement, factory silver brake system 2-line compressed air brake system spring-loaded parking brake 2 interchangeable coupling heads at the front, with connecting lines to the motor vehicle, 24 volt ABS and ALB, with ABS plug at the front, with connecting cable electrics 24 volt, multi-chamber lights, yellow LED lighting on the side 2 white position lights at the front 2 white/red lane keeping lights at the rear 2 x 7-pin interchangeable plugs at the front, with connecting cable, LED rotating beacon with holder, switched via parking light (light removable) pair of warning signs with double LED lighting and extendable to 3,000mm Ledpfx Alouytx Sedeac floor front bend with steel/checker plate covering storage box embedded in the crossing slope to the bend then with approx. 70mm softwood floor, in the wheel arch area steel/checker plate covering rear bevel with 70mm softwood floor Low loading area including rear bevel 6,500mm Loading ramps Steel ramps 2,800mm long, 750mm wide, can be moved sideways Additional ramp lock foldable at the bottom (to prevent the ramps from slipping sideways, not in conjunction with lateral hydraulic ramp shifting) Covered with wood (tip area with steel/checker plate) Hydraulic via tractor auxiliary drive with throttle, actuation on the side in FR left Hydraulic connection with SVK plug NW 10/3, including connecting hose Paintwork Frame hot-dip galvanized including passivation Loading ramps hot-dip galvanized Plus pre-freight / provision from storage location 26639 Wiesmoor 1,280.00 €/ net

Condition: new, maximum load weight: 30,010 kg, overall weight: 40,000 kg, axle configuration: > 3 axles, loading space length: 10,000 mm, loading space width: 2,520 mm, loading space height: 900 mm, total width: 2,550 mm, Brand-new Fliegl 4-axle low-bed trailer with wheel recesses and split ramps, type VTS 400 RM Hire-purchase offer: 48-month term, down payment only the VAT, final residual value 40% Monthly rate: EUR 899.00 Vehicle / Body: Low-bed trailer First registration: New vehicle Gross weight: 24,000kg/40,000kg Unladen weight: 9,990kg Payload: 14,010kg / 30,010kg Overall length: 12,000mm Loading length: total approx. 10,000mm, gooseneck approx. 2,850mm, load bed including rear taper approx. 7,150mm Width: 2,550mm Loading height: 900mm Further information Chassis: Low-bed trailer Steel welded construction Turntable with heavy-duty ball race Lodpfetrizksx Aldjac Foldable rear support Wheel chocks with holders Aluminum side underrun protection Full-width rear spray flap Half-shell mudguards 1st and 2nd axle with anti-spray mud flaps behind each axle, anti-spray mud flap behind the 4th axle Excavator arm trough above rear axles, from the rear axle to the rear approx. 1,800mm long, approx. 650mm wide and 150mm deep 2 pairs of lashing holes, each 5t, in the excavator arm trough, on the longitudinal frame approx. 300mm from the front and approx. 200mm before the rear taper Spare wheel bracket for 1 spare wheel, upright on the gooseneck, front center, spare wheel brand same as main equipment, steel rim Toolbox let into the floor on the gooseneck with lid, W=720mm / L=520mm / D=170mm 1st pair of wheel recesses after the gooseneck, let into the deep deck in the driving lane, chamfered for access, length at the bottom approx. 1,600mm, approx. 400mm deep. Note! Frame in the main beam area 400mm higher than the wheel recess. 2nd pair of wheel recesses between the axles, let into the deep deck in the driving lane, chamfered for access, length at the bottom approx. 600mm, approx. 300mm deep. Note! Frame in the main beam area 300mm higher than the wheel recess. Extensions retractable to 3,000mm (no extension at the rear taper and not in the wheel recesses below) (track width of machines or vehicles to be transported must not exceed the outer frame width of 2,550mm) Storage compartment for timber planks underneath the low-bed deck 70mm timber planks for extension to 3,000mm Lashing points – low-bed trailer 1 pair of RIN lashing rings inlaid at the front on the gooseneck, each 5t 4 pairs of lashing holes in the outer frame, each 5t (for securing strap attachments) 8 pairs of lashing mushrooms flush-mounted top and side in the outer frame, each 10t 2 at the front on the gooseneck 6 in the deep deck First lashing ring 250mm from the front, last a maximum of 250mm from the rear, spacing between lashing rings not more than 1,100mm 5 pairs of stake pockets inlaid in the outer frame, inner dimensions 70 x 40mm (convertible to 5t ring lashing eyes, not included) 1 pair of foldable lashing rings additionally inlaid in the floor, each 10t 1 inside next to main frame at start of low-bed section 2 pairs of additional foldable lashing rings, each 10t 1 on the gooseneck (protrudes) 1 behind the last axle inlaid in the floor Towing device for turntable trailer Drawbar with certified 50mm towing eye, towing eye inclined by 8° D-value at least 160kN Axles and Suspension BPW drum braked axles "Axles/chassis laser aligned" – reduces tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bushings and mechanical front axle load equalization (rocker equalizer) Wheels and Tires 235 / 75 R 17.5" Manufacturer’s choice, with M + S marking Steel rims in twin arrangement,

Condition: new, maximum load weight: 23,890 kg, overall weight: 30,000 kg, axle configuration: 3 axles, Vehicle from current production NEW VEHICLE Fliegl 3-axle low-loader, type DTS 300, hot-dip galvanized Total weight 24,000 kg / 30,000 kg Payload 17,890 kg / 23,890 kg Ledpfxok N Adks Aldoac Unladen weight 6,080 kg Overall length 10,900 mm Loading length 8,680 mm Loading bed 6,500 mm incl. 900 mm approach ramp Loading height 860 mm Air suspension with raising and lowering valve Long ramps 2,800 mm with hydraulic operation Extensions to 3,000 mm with warning signs and rotating beacon Large lashing kit with 5.0 and 10.0 ton lashing points 5 pairs of stake pockets Drawbar eye 40 mm plus pre-carriage / preparation costs from storage location Wiesmoor 1,280.00 € / net Lease-purchase offer: Term 48 months, residual value 40%, down payment only the VAT. Monthly rate: EUR 609.00

Condition: used, maximum load weight: 33,787 kg, overall weight: 39,000 kg, axle configuration: 3 axles, first registration: 07/2017, next inspection (TÜV): 01/2027, loading space length: 7,200 mm, loading space width: 2,350 mm, total width: 2,550 mm, Gross weight: 39,000 kg / 35,000 kg Tare weight: 5,213 kg Payload: 33,787 kg / 29,787 kg Overall length: 8,200 mm Loading length: 7,200 mm Width: loading width 2,350 mm / total 2,550 mm Additional information - Internal bin height: 1,450 mm - Volume: 24.5 m³ - Fifth wheel height: 1,200 mm - Tarpaulin bar with bracket - BPW axles Ljdpsycbi Refx Aldsac - Air suspension - Steel round-body in "tub shape" - Rear wall as pendulum tailgate - Work platform with access steps - One-sided roll tarp Vehicle may be wrapped or labeled with advertising.

Condition: new, maximum load weight: 8,665 kg, overall weight: 11,800 kg, axle configuration: 2 axles, loading space length: 6,200 mm, loading space width: 2,480 mm, loading space height: 910 mm, total width: 2,550 mm, NEW VEHICLE Fliegl Tandem Trailer for Timber Transport with Stakes, Model TPS 118 Holz Total weight: 11,800 kg Unladen weight: 3,135 kg Payload: 8,665 kg Overall length: 8,350 mm Loading length: 6,200 mm Width: 2,550 mm Loading height: 910 mm Additional information plus freight/handling ex stock location 26639 Wiesmoor €1,280.00 net Loading width: 2,480 mm Chassis: Central axle trailer Fine-grained steel welded construction Outer frame slightly sloped with "Load-Lock profile" for attaching lashing straps Front telescopic support leg Folding rear support 1 plastic toolbox, width = 600 / height = 425 / depth = 460 mm, lockable Open storage compartment for stake inserts under the loading platform 4 pairs of stake pockets recessed in the outer frame, 83 x 83 mm internal dimensions 4 stake pockets centrally recessed in the floor, reinforced to the main frame, 83 x 83 mm internal dimensions 6 pairs of insertable stakes B = 80 / D = 80 / L = 2,000 mm, hot-dip galvanized Note: Stake pockets/inserts are not suitable for securing long materials, pipes, etc. without additional lashing Side underrun protection aluminium Tandem trailer towing assembly Drawbar with certified 40 mm towing eye Drawbar mechanically adjustable by 4 x 500 mm within 1,800 - 3,800 mm, standard drawbar set to 1,800 mm (Note! Observe load distribution and drawbar load) Axles & Suspension GFA or BPW axles, manufacturer’s choice, with tapered roller bearings and S-cam brakes "Axle/chassis laser aligned" – reduces tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bushings and mechanical axle equalization (rocker balancing) Wheels and Tires 235 / 75 R 17.5" Steel rims, factory silver Braking System 2-line compressed air brake system Spring-loaded parking brake Integrated air reservoir 2 non-interchangeable coupling heads at the front, with connection lines to the truck ABS and ALB, with front ABS plug, including connection cable Attention: This trailer may only be towed by towing vehicles capable of ensuring full ABS function! Electrics 24 Volt, LED multi-chamber rear lamps, lateral amber LED lamps, LED license plate light (note: With some towing vehicles, false diagnostics may appear even if lighting functions are correct) 2 front white LED position lamps 2 rear white/red lane marker LED lamps 2 x 7-pin non-interchangeable plugs at the front, with connection cable Floor Antislip plywood, approx. 30 mm thick, designed for high point loads Note: Floor waviness is possible due to environmental impacts! Platform length approx. 6,200 mm Operating Notes The total permissible weight given is technically possible, but depending on load, actual usage may be limited by max. axle, drawbar, or kingpin loads. Special permit required if total towing length exceeds 18,750 mm. National regulations must be observed. Registration / Plates Registration country: Germany With DEKRA inspection and certificate 24/7 service hotline Prepared for single-line license plate holder Outline marking with ECE R 048 reflective tape, white sides and red rear Paintwork Chassis hot-dip galvanized including passivation "15-year corrosion warranty" Ledpfxjw N U I Hj Aldjac Note: Floor warping can occur due to hot-dip galvanization! Vehicle from current production – delivery time approx. 2–3 weeks.

Condition: new, maximum load weight: 18,400 kg, overall weight: 24,000 kg, axle configuration: 3 axles, loading space length: 5,900 mm, loading space width: 2,500 mm, loading space height: 860 mm, total width: 2,520 mm, Gross vehicle weight: 24,000 kg / 30,000 kg Unladen weight: 5,600 kg Payload: 18,400 / 24,400 kg Total length: 10,290 mm Loading length: 5,900 mm including rear slope Width: 2,520 mm Loading height: 860 mm Further information Plus pre-freight / Delivery from storage location 26639 Wiesmoor €1,280.00 / net Low-loader trailer chassis Steel welded construction Turntable with sturdy ball-bearing slewing ring Foldable rear support Wheel chocks with holder Rear mud flaps across the entire width 1 plastic toolbox Prepared for extensions to 3,000 mm (holes in the outer frame with cover, not in the rear slope) Low-loader lashing eyes 1 pair Lashing cutouts in the front longitudinal member, 10 tons each. 7 pairs of lashing pins, 10 tons each, embedded in the outer frame at the top and sides. 1 x at the front, 10 tons each. 5 x in the lowbed. 1 x in the rear slope. 12 pairs of lashing holes in the outer frame, 5 tons each. (Tire strap attachment) 5 x offset, 6 x drop-bed, and 1 x in the rear slope Trailer turntable drawbar Drawbar with tested 40 mm drawbar eye Drawbar height adjustment via spring Axles + Suspension Drum brake axles, at the manufacturer's discretion "Laser-measured axle/chassis" reduces tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation (Rocker compensation) Wheels and Tires 235/75 R 17.5" at the manufacturer's discretion Twin-axle steel rims, factory silver Brake System Two-line pneumatic brake system Spring-loaded parking brake Two interchangeable coupling heads at the front, with connecting lines to the towing vehicle Connecting lines extended by approximately 60 cm Without ABS, but with mechanical ALB then max. 60 km/h approval Electrics 12-volt, multi-chamber lights, without yellow LED side lighting, side reflectors 2 white position lights at the front 2 white/red lane departure lights at the rear 1 x 7-pin 12-volt connector at the front, with connecting cable, extended by approximately 60 cm 1 LED rotating beacon with bracket, switched via parking light (light removable) 2 pairs of warning signs with double LED illumination and extendable to 3,000 mm Floor Front offset with steel/checker plate flooring Storage box recessed into the ramp to the offset then with 70 mm softwood flooring, steel/checker plate flooring in the wheel arch area Lsdpjwlmr Dofx Aldjac Rear slope with 70 mm softwood flooring Low-bed area including rear slope 5,900 mm Load-up ramps Steel ramps 2,800 mm long, 750 mm wide, laterally movable covered with wood (Tip section with steel/checker plate) Hydraulic via tractor PTO with throttle, actuated on the side in FR left-hand drive Hydraulic connection with SVK connector NW 10/3, including connecting hose Operating Instructions For 10,000 kg axle load, an exemption is required; only indivisible loads are possible!!! The stated gross weight is technically possible; depending on the load, the gross weight may not be achieved while complying with the permissible axle/support and fifth wheel loads. (Poor handling and caster behavior due to incorrect load distribution is possible) Country of Registration/Signs Country of Registration: Germany with DEKRA approval and certificate, for max. 60 km/h approval, towing vehicle LoF, (Country of Registration Switzerland: max. 40 km/h possible) prepared for two-line license plate holder without contour markings/reflective stripes according to ECE R 048 Frame paint finish: RAL 7021 Black-gray "10-year warranty a

Condition: new, maximum load weight: 31,920 kg, overall weight: 40,000 kg, axle configuration: > 3 axles, loading space length: 10,410 mm, loading space width: 2,500 mm, loading space height: 900 mm, total width: 2,550 mm, New vehicle Fliegl 4 axle low loader trailer with ramps, type VTS 400 Total weight: 24,000kg/40,000kg Empty weight: 8,080kg Payload: 15,920kg/31,920kg Total length: 11,940mm Loading length: total approx. 10,410mm, offset approx. 2,490mm, loading bed including rear bevel approx. 7,920mm Width: 2,550mm Loading height: 900mm Further information plus pre-freight / provision from storage location 26639 Wiesmoor 1,280.00 ¤/ net Rent-purchase offer: term 48 months, down payment only VAT, residual value 40% monthly rate EUR 759.00 Chassis Low-loader trailer Steel welded construction Turntable with strong ball bearing ring Foldable rear support 2 wheel chocks with holder Aluminum side impact protection Rear splash flaps across the entire width Half-shell mudguards 1st + 2nd axle with anti-spray splash flaps behind each axle, Anti-spray splash flaps in front of and behind 3rd and 4th axle Excavator arm recess over the rear axles starting at the rear, approx. 1800 mm long, approx. 650 mm wide and approx. 150 mm deep, 2 pairs of lashing holes, each 5 tons. in the excavator arm recess on the side of the longitudinal frame approx. 300 mm from the front and approx. 200 mm in front of the rear bevel 1 plastic tool box, w=600 / h=425 / d=460 mm, lockable Storage box embedded in the floor on a crank with lid, W=720 mm/ L=520 mm / D= 170 mm Extensions extendable to 3,000 mm (not in the rear bevel) (The track width of the construction machines or vehicles to be transported must not exceed the outer frame width 2,550 mm) Storage compartment for wooden planks below the low-loading area Wooden planks 70 mm for widening to 3,000 mm Lashing eyes for low-loader 1 pair of lashing cutouts embedded in the longitudinal beam at the front on a crank, 10 tons each. 4 pairs of lashing holes in the outer frame, each with 5 tons (tension belt attachment) 9 pairs of lashing mushrooms, each 10 tons, embedded in the outer frame at the top and side 2 x at the front on the bend 7 x in the low bed First lashing eye 250 mm from the front and last max. 250 mm from the back, distance between the lashing eyes not greater than 1100 mm 3 additional pairs of folding lashing eyes, each 10 tons 1 x on the bend (sticks out) 1 x at the beginning of the low bed, embedded inside on the longitudinal beams 1 x embedded in the floor behind the last axle Towbar with tested 50 mm towing eye Towbar height adjustment via spring Axles + suspension Drum brake axles, as selected by the manufacturer "Laser-measured axles/chassis" Reduction in tire wear and fuel consumption Air suspension with raising & lowering valve + Auto-reset function Wheels and tires 235 / 75 R 17.5" at the manufacturer's choice Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-loaded parking brake Lajdsvv D Ixepfx Aldec Axle load detection via EBS-Canbus signal, for display on display in the driver's cab, truck must be prepared accordingly, no truck installed (no calibrated scales) Vehicle - driving stability system 2 interchangeable coupling heads at the front, with connecting cables to the motor vehicle, 12-24 volt EBS, electronic braking system with EBS plug at the front, with connecting cable Knorr brand Caution: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrics 12-24 volts, multi-chamber LED lights, yellow LED lighting on the side, license plate lighting in LED, (Note! Incorrect diagnoses can occur with certain towing vehicles, although the function is p

Condition: new, maximum load weight: 10,600 kg, overall weight: 14,000 kg, axle configuration: 2 axles, loading space length: 6,200 mm, loading space width: 2,480 mm, loading space height: 900 mm, total width: 2,550 mm, Vehicle / Body: Tandem Trailer First Registration: New vehicle Gross Weight: 14,000 kg Unladen Weight: 3,400 kg Payload: 10,600 kg Overall Length: 8,080 mm Loading Length: 6,200 mm (including rear bevel) Width: 2,550 mm Loading Height: 900 mm Additional Information plus freight/preparation from storage location 26639 Wiesmoor: €1,280.00 net - Platform width approx.: 2,480 mm - Drawbar length approx.: 1,750 mm Vehicle consists of: Chassis: central axle trailer Fine-grain steel welded construction Outer frame slightly sloped, new design with "Load-Lock profile" for lashing strap attachment Laodpfx Aley Dzk Sodsc 6 pairs of lashing rings outside in the floor/frame, each 5t 3 pairs of lashing rings outside in the floor, each 5t 1 x front corners, 1 x before and 1 x in the rear bevel at the back Gear support leg at front Foldable rear supports Wheel chocks with holder Steel underride guard Full-width spray/splash guards at the rear (not with forklift bracket) Quarter fenders 1 plastic toolbox, w=600 / h=425 / d=460 mm, lockable Coupling device: Central axle trailer Drawbar with certified 40 mm towing eye Drawbar height-adjustable via spindle, max. 250 mm adjustment range Axles & Suspension: Drum brake axles, manufacturer’s selection Laser-aligned axles/chassis for reduced tire wear and fuel consumption Air suspension with raise/lower valve Wheels and tires: 235/75 R 17.5”, manufacturer’s selection Steel twin wheels, factory silver Brake system: 2-line compressed air brake system Spring-loaded parking brake 2 non-interchangeable coupling heads at the front, with connection to the truck 24 Volt EBS (electronic braking system) with EBS plug at the front and connection cable Note: This trailer may only be towed by vehicles that guarantee ABS functionality! Electrics: 24 Volt, multi-chamber lights, yellow LED side marker lights 2 white front position lights 2 white/red lane guidance lamps at the rear 2 x 7-pin non-interchangeable plugs at the front, with connection cable Floor: Steel/chequer plate floor for high point load capacity Note: Slight floor warping possible due to welding distortion! Platform length approx. 6,200 mm Rear bevel approx. 900 mm Front bulkhead / front corner posts: 25 mm aluminum hollow section, 400 mm high Side walls: 25 mm aluminum hollow section, 400 mm high, foldable and removable Rear wall / rear corner stakes: 1 pair of steel stakes fixed to the frame, with retention bracket for the loading ramps, entry width approx. 2,430 mm Access ramps: Steel ramps, 2,300 mm long, 510 mm wide, laterally adjustable With hand grip on ramps Wood-covered (tip section with steel/chequer plate) With gas strut for one-person operation Operating instructions: The stated gross weight is technically feasible; depending on the load, the total weight may not be achievable within legal axle, support, and coupling load limits. (Poor handling or trailing behavior possible due to improper load distribution.) Special permit required if total towing length exceeds 18,750 mm. Observe country-specific registration regulations. Country of registration / Number plates: Registration country: Germany With Dekra inspection and report (according to §13 EC-FGV) 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips according to ECE R 048, white at sides and red at rear Paintwork: Frame: DB 7350 Nova Grey "10-year warranty against corrosion rust-through" Front bulkhead: aluminum Side walls: anodized aluminum Access r

Condition: new, maximum load weight: 8,780 kg, overall weight: 11,800 kg, axle configuration: 2 axles, loading space length: 5,000 mm, loading space width: 2,420 mm, loading space height: 950 mm, total width: 2,550 mm, Further information plus pre-carriage / provision from storage location 26639 Wiesmoor €1,280.00 net Chassis Central Axle Tipping Trailer Steel welded construction, continuous tipping shaft at the rear with 80 mm spherical tipping bearing Support leg with gear at the front Foldable rear support 2 wheel chocks with holders Lodpey Dzlcofx Aldsac Steel underrun protection Full-width rear mudflaps Quarter-shell fenders 1 plastic toolbox, w=600 / h=425 / d=460 mm, lockable Note! Sidewall touches the toolbox when folded down. Lockable storage space for loading ramps beneath the loading area WITHOUT ramps Drawbar for central axle trailer Drawbar with certified 40 mm towing eye Drawbar height adjustable via spindle, max. adjustment range 300 mm Axles & Suspension BPW drum brake axles "Chassis/undercarriage laser-aligned" to reduce tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bushings and mechanical axle load equalization (rocker compensation) Wheels and Tyres 235 / 75 R 17.5" manufacturer’s choice Steel rims, factory silver Brake System 2-line air brake system Color-coded line routing for easy service Hand spindle parking brake Integral air tank ABS and ALB, with ABS connector at the front and connection cable Caution: The trailer may only be towed by vehicles that ensure the effectiveness of the ABS! 2 non-interchangeable coupling heads at the front, with connection lines to the truck Electrics 24 Volt, multi-chamber lighting, side yellow LED marker lights 2 white position lights at the front 2 white/red lane lights at the rear 2 x 7-pin non-interchangeable plugs at the front, with connection cable Hydraulics Three-way tipping system, hydraulic multi-piston cylinder with lift limiter and safety cable Low-pressure cylinder up to max. 170 bar, without flow restrictor. If required, needs to be retrofitted on the truck. Hydraulic connection with SVK plug NW 10/3, incl. connecting hose Operated hydraulically via truck PTO Tipping Platform Robust tipping platform with 4 mm steel floor, steel sidewall construction, continuous, fold-down sidewalls Non-swing mounted without central locking underneath. Plug-in corner posts at the rear. Rear wall fold-down and swing-mounted, central locking underneath. Platform length approx. 5,000 mm, sidewalls with 6 hinges at the bottom Sidewall retracting springs (not possible with split sidewalls) Platform width 2,420 mm 5 pairs of lashing rings in the floor, each rated to 5 tons Operating Notes The specified gross weight is technically possible; depending on the load, the gross weight may not be achievable while observing permissible axle/support/kingpin loads. (Poor driving and trailing performance possible due to incorrect load distribution) Approval/Country Country of registration: Germany with Dekra inspection and certificate (in accordance with §13 EC-FGV) 24/7 service hotline Prepared for single-line number plate holder Contour marking with reflective tape according to ECE R 048, white on sides and red at the rear Paintwork Frame hot-dip galvanized including passivation "15-year guarantee against rust-through" Sidewalls/platform RAL 5002 ultramarine blue Note! Platform inside is only primed unless otherwise painted bridge design! Optional loading ramps €1,280.00 net

Condition: new, maximum load weight: 8,840 kg, overall weight: 11,800 kg, axle configuration: 2 axles, loading space length: 6,200 mm, loading space width: 2,480 mm, loading space height: 900 mm, total width: 2,550 mm, Total length: 8,000 mm Loading length: 6,200 mm including rear chamfer Further information plus freight / provision from stock location 26639 Wiesmoor €1,280.00 net Loading width: 2,480 mm Chassis: central axle trailer Fine-grain steel welded construction Outer frame, slightly angled, new version with “Load-Lock profile” for lashing strap attachment Pair of lashing rings on the outside base, each 5 t 1 x in the front corners, 1 x in front of and 1 x in the rear chamfer at the back 6 pairs of lashing rings on the outer floor/frame, each 5 t Gear support leg at the front Rear support, foldable Wheel chocks with holder Ledpfx Ajyl E Dqeldjac Aluminum side underrun protection Galvanized steel rear underrun guard Full-width rear spray flaps (not in conjunction with forklift mount) Quarter-circle mudguards 1 plastic toolbox, w=600 / h=425 / d=460 mm, lockable Towing device for central axle trailer Drawbar with tested 40 mm towing eye Drawbar height-adjustable via spindle, max. adjustment range 300 mm Axles & suspension GFA or BPW axles according to manufacturer’s choice, with tapered roller bearings and S-cam brakes "Axle/chassis laser alignment" reduces tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber mounting and mechanical axle load equalizing (rocker equalizer) Braking system 2-line compressed-air braking system Color-coded piping for easy service Hand-spindle parking brake 2 non-interchangeable coupling heads at the front, with connection lines to the towing vehicle 24 volt ABS and ALB, with ABS plug at the front, with connection cable Attention: The trailer may only be towed by towing vehicles that guarantee proper functioning of the ABS! Wheels and Tires 235/75 R17.5, make as per manufacturer’s choice Steel rims, factory silver Electrics 24 volt, multi-chamber lamps, side yellow LED lighting 2 white position lamps at the front (LED) 2 white/red marker lamps at the rear 2 x 7-pin non-interchangeable plugs at the front, with connection cable Floor Steel/chequer plate floor for high point load capacity Note: Slight floor waviness due to welding distortion possible! Platform length approx. 6,200 mm Rear chamfer approx. 900 mm Front bulkhead / corner stakes 25 mm aluminum hollow section, 400 mm high Side walls 25 mm aluminum hollow section, 400 mm high, foldable and removable Intermediate posts Without intermediate posts Rear wall / rear corner posts 1 pair of steel posts attached to the frame, with holder to lock the loading ramps, entry width approx. 2,430 mm Loading ramps Steel ramps, 2,300 mm long, 510 mm wide, laterally adjustable With carrying handle on the ramps With wooden covering (tip area with steel/chequer plate) With gas strut for single-person operation Operating Notes The specified gross weight is technically feasible; depending on the cargo, the gross weight may not be achievable while adhering to permissible axle, support, and kingpin loads. (Poor driving and tracking properties possible with incorrect load distribution) Country of registration / plates Germany With Dekra inspection and certificate (according to §13 EC - FGV) 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips as per ECE R 048, white at the sides, red at the rear Paintwork Frame: DB 7350 Novagrau Front bulkhead: aluminum Side walls: aluminum, anodized Loading ramps: hot-dip galvanized

Condition: used, maximum load weight: 8,470 kg, overall weight: 11,800 kg, axle configuration: 2 axles, first registration: 06/2018, loading space length: 5,000 mm, loading space width: 2,420 mm, loading space height: 900 mm, total width: 2,550 mm, Gross weight: 11,800 kg Unladen weight: 3,330 kg Payload: 8,470 kg Overall length: 6,950 mm Loading length: 5,000 mm Width: 2,550 mm / loading width approx. 2,420 mm Loading height: approx. 950 mm Further information: - Front support leg - Rear support, foldable - 450 mm drop sides - Large lashing package Laedpfx Asy Arkasldoc - Frame hot-dip galvanized incl. passivation - Loading ramps optional: €1,280.00

Condition: new, maximum load weight: 25,050 kg, overall weight: 35,000 kg, axle configuration: 3 axles, loading space length: 13,500 mm, loading space width: 2,500 mm, loading space height: 950 mm, total width: 2,550 mm, Total weight: 35,000 kg / 48,000 kg Unladen weight: 9,950 kg Payload: 25,050 kg / 38,050 kg Overall length: 21,000 mm Loading length: loading area approx. 13,500 mm / max. loading length 21,000 mm Width: 2,550 mm Loading height: 950 mm Additional information: Brand-new vehicle from ongoing production, available from approx. week 8/2026 Telescopic rear support 4 wheel chocks with holders 4 pairs of recessed container locks in the floor, suitable for 1x 40 ft. container or 2x 20 ft. containers Lodpfx Aoumha Njldeac 1 spare wheel holder for 1 spare wheel, with wheel fastening kit, basket design 11 pairs of stake pockets recessed in the outer frame, suitable for FR plug-in stakes 80x50 mm, installed flush with the outer frame, with opening for lashing strap or chain hooks 20 plug-in stakes, W=80 mm / D=50 mm / L=1500 mm 1 plastic toolbox 3 pairs of lashing eyes, each rated at 3.5 t, fitted to the side frame - in the gooseneck area 13 pairs of foldable lashing rings, each rated at 10,000 daN, suspended freely swiveling along the side frame profile (also suitable for wide-load securing) 1 pair of foldable lashing rings, each rated at 10,000 daN, installed laterally in the intermediate support Air suspension with raise and lower function 1st axle: automatic lift axle, additionally with forced lowering including starting aid with operator button on the semi-trailer, no cab operation with lift & lower valve + auto reset function Wheels and tires: 235 / 75 R 17.5" Steel rims, twin arrangement, factory silver 24 volt, multi-chamber lights, lateral yellow LED lighting 2 white LED position lights at the front 2 white/red lane marker lights at the rear, LED 2 x 7-pin and 1 x 15-pin confusion-proof sockets at the front, without connecting cable 2 additional LED work lights at the rear, switched via reversing light 1 removable rotating beacon on the underrun protection 1 x 7-pin socket at the rear 6 lateral sockets, 2x front wall, 2x landing legs, 2x rear end (left + right) 7-pin 2 work lamps recessed at the top in the front wall incl. switch 2 pairs of oversize boards, each with 2 LED marker lights per board, extendable sideways up to 3,500 mm, boards can also be attached to the loading area (width adjustment infinitely variable) Fixed steel front wall, 1,200 mm high, with robust steel corner posts without corner bevel, straight lateral design. 2 lashing holes at the top, inside and outside, in the front wall corners Front frame hot-dip galvanized + visible area of outer frame, finish painted in RAL 3002 Carmine Red Rear frame hot-dip galvanized + visible area of outer frame, finish painted in RAL 3002 Carmine Red Front wall RAL 3002 Carmine Red

Condition: new, maximum load weight: 15,080 kg, overall weight: 21,000 kg, axle configuration: 1 axle, NEW VEHICLE Fliegl 1-axle special low-bed trailer Total weight 21,000 kg Payload 15,080 kg Unladen weight 5,920 kg Overall length 13,630 mm Loading length 9,940 mm Lajdpfx Asllwitoldsc Low-bed, sloping from the wheel area to a loading height of 210 mm Attachment rail for aluminum ramps at the rear of the vehicle, spanning the full width Towing eye at the rear Electric winch with a pulling force of 8,165 kg and remote control, cable length 35 meters 1 pair of wheel recesses approx. 700 mm behind the gooseneck, integrated into the floor 2 pairs of plug-in wheel stops, 4 plug-in positions Large lashing kit BPW drum brake axle Air suspension with lifting and lowering valve Complete LED lighting 1 pair of aluminum loading ramps, load capacity 12,000 kg, storage compartment in the center of the loading area Frame hot-dip galvanized, outer frame painted red Plus pre-carriage / preparation costs from storage location Wiesmoor 1,280.00 EUR / net New vehicle without initial registration, with full manufacturer's warranty Vehicle is immediately available Lease-purchase offer: Term 48 months, residual value 40%, down payment only the VAT Monthly rate EUR 899.00 (other terms are possible)

Condition: new, maximum load weight: 8,000 kg, overall weight: 10,500 kg, axle configuration: 2 axles, loading space length: 5,500 mm, loading space width: 2,050 mm, loading space height: 630 mm, total width: 2,550 mm, Vehicle / Body: Tandem Low-Bed Trailer First Registration: New vehicle Gross Vehicle Weight: 10,500 kg Unladen Weight: 2,500 kg Payload: 8,000 kg Overall Length: 7,280 mm Loading Length: Platform length approx. 5,500 mm Width: Platform width 2,050 mm / 2,550 mm Loading Height: Platform height 630 mm Additional Information plus freight/preparation from stock location 26639 Wiesmoor €1,280.00 / net - Overall height approx.: 2,900 mm - Side wall height approx.: 400 mm - Frame RAL 5001 Blue Green Chassis: Central axle low-bed trailer Fine-grain steel welded construction Telescopic support leg at the front Telescopic rear support Wheel chocks with holder Steel fenders over both wheels Drawgear for central axle trailer Drawbar with certified 40 mm towing eye Drawbar height-adjustable via spindle, max. adjustment range 250 mm Axles + Suspension Euro axles at our discretion, with tapered roller bearings and S-cam brakes "Axle/chassis laser alignment" reduces tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bushings and mechanical axle load equalization (rocker compensation) Wheels and Tires 235/75 R 17.5" manufacturer's choice Laedpswwab Ajfx Aldjc Steel rims, factory silver Braking system 2-line compressed air brake system Spring-actuated parking brake 2 fail-safe coupling heads at the front, with connection lines to tractor unit, ABS and ALB, with ABS connector at the front, with connection cable Attention: The trailer may only be towed by vehicles that ensure the effectiveness of the ABS! Electrics 24 Volt, multi-chamber lamps, side yellow LED lighting 2 white position lights at the front 2 white/red lane marker lights at the rear 2 x 7-pin fail-safe connectors at the front, with connecting cable, TTS Platform low-mounted steel trough, platform floor with steel/chequer plate covering, steel sides solidly welded to the floor Braking system 2-line compressed air brake system Spring-actuated parking brake 2 fail-safe coupling heads at the front, with connection lines to tractor unit, 24 Volt ABS and ALB, with ABS connector at the front, with connection cable Attention: The trailer may only be towed by vehicles that ensure the effectiveness of the ABS! Electrics 24 Volt, multi-chamber LED lamps, side yellow LED lighting, license plate lighting in LED, (Note: with certain tractor units, incorrect diagnostics may occur even though the functions are in operation) 2 white position lights at the front in LED 2 white/red lane marker lights at the rear in LED 2 x 7-pin fail-safe connectors at the front, with connecting cable, park sockets for electrics / ABS / air connections on the drawbar TTS Platform low-mounted steel trough, platform floor with steel/chequer plate covering, steel sides solidly welded to the floor Platform length 5,500 mm Trough at front and sides with "Load-Lock Profile" for lashing straps (8 in front, 16 per side) Note: Minor unevenness in the floor due to welding distortion possible! 2 pairs of lashing eyes, 1 x in the front corners of the steel trough and 1 x in the floor rear, each 5t 3 pairs of additional lashing eyes in the floor, each 5t 4 pairs of lashing eyes bolted onto the side walls Ramps Steel ramps, 2,300 mm long, 510 mm wide, laterally adjustable with handgrip on the ramps Ramp surface with "Mega Grip" made of serrated grating (contact area with steel/chequer plate) with gas pressure springs for one-man operation

Condition: new, maximum load weight: 17,900 kg, overall weight: 24,000 kg, axle configuration: 3 axles, loading space length: 8,670 mm, loading space width: 2,500 mm, loading space height: 860 mm, total width: 2,520 mm, New vehicle Fliegl 3 axle low loader trailer with ramps, type DTS 300 Vehicle completely hot-dip galvanized Total weight: 24,000kg/30,000kg Empty weight: 6,100kg Payload: 17,900/23,900kg Total length: 10,890mm Loading length: 8,670mm total, 6,500mm low bed including rear bevel / 2,170mm offset Width: 2,520mm Loading height: 860mm Further information plus pre-freight / provision from storage location 26639 Wiesmoor 1,280.00 ¤/ net Rent-purchase offer: term 48 months, down payment only VAT, residual value 40% monthly rate: EUR 569.00 Steel Welded construction Pivot bolster with strong ball bearing ring Foldable rear support Wheel chocks with holder Aluminum side impact protection Splash flaps at the rear over the entire width (not in conjunction with forklift bracket) Half-shell mudguard on 1st axle with anti-spray splash flaps Anti-spray splash flaps behind 2nd and 3rd axles 1 plastic tool box, w=600 / h=425 / d=460 mm, lockable Extensions extendable to 3,000 mm (not in the rear bevel) (The track width of the construction machines or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Storage compartment for wooden planks in the middle of the loading area 70 mm wooden planks for widening to 3,000 mm Lashing eyes for low loader 1 pair of lashing cutouts in the longitudinal beam at the front on a bend, 10 tonnes each. 4 pairs of lashing holes in the outer frame of the crank, each with 5 tons (tension belt attachment) 7 pairs of lashing mushrooms, set into the outer frame at the top and side, each with 10 tons 1 x at the front on the crank 6 x in the low bed First lashing eye 250 mm from the front and last max. 250 mm from the back, distance between the lashing eyes not greater than 1100 mm 5 pairs of ring lashing eyes set into the outer frame, each with 5 tons (can be converted to stake pockets) 2 additional pairs of folding lashing eyes, each with 10 tons 1 x on the crank (protrudes) 1 x set into the ground behind the last axle Towbar with tested 40 mm towbar Towbar height adjustment via spring Axles + suspension Ledpov D T R Esfx Aldsac Drum brake axles, as selected by the manufacturer "Laser-measured axle/chassis" Reduction in tire wear and tear Fuel consumption Air suspension with raising and lowering valve Wheels and tires 235 / 75 R 17.5" at the manufacturer's discretion Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-loaded parking brake Vehicle driving stability system Axle load detection via EBS-Canbus signal, for display on display in the driver's cab, truck must be prepared accordingly, no truck installed (no calibrated scales) 2 interchangeable coupling heads at the front, with connecting cables to the motor vehicle, 24 volt EBS, electronic braking system with EBS plug at the front, with connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrics 24 volts, multi-chamber lights, yellow LED lighting on the side 2 white position lights at the front 2 white/red lane keeping lights at the rear 2 x 7-pin, interchangeable plugs at the front, with connecting cable, 1 LED rotating beacon with holder, switched via parking light (light removable) 2 pairs of warning signs with double LED lighting and extendable to 3,000 mm Floor Front bend with steel/checker plate covering Storage box embedded in the crossing slope to the bend then with approx. 70 mm softwood floor, steel/checker plate covering in the wheel arch area Rear bev

Condition: new, maximum load weight: 30,310 kg, overall weight: 40,000 kg, axle configuration: > 3 axles, NEW VEHICLE Fliegl 4-axle low loader with 2 pairs of wheel recesses and ramps Total weight 40,000 kg Payload 30,310 kg Empty weight 9,690 kg Total length 12,000 mm Loading length 10,000 mm Loading bed 7,150 mm including 850 mm approach slope Loading height 900 mm 1st pair of wheel recesses after offset in the loading bed, bottom length approx. 1,600 mm, 400 mm deep 2nd pair of wheel recesses between the axles in the loading bed, bottom length 600 mm, 300 mm deep Extensions to 3,000 mm, warning signs, rotating beacon, large lashing package 5 pairs of stake pockets in the outer frame Excavator arm recess 1,800 mm long, 150 mm deep Drawbar 50 mm Air suspension with lifting and lowering valve, can be operated separately BPW drum brakes Tires 235 / 75 R 17.5" Axle load detection via EBS CAN bus signal, Trailer Info Center Ramps 2,800 mm x 750 mm with hydraulic actuation Hydraulic side shift Rent-purchase offer: term 48 months, residual value 40%, down payment only VAT on the rental rates, monthly rate EUR 970.00 net Vehicle will be available from September 11th, 2023 from the Neumünster trade fair. Laedpfxonzlg Do Aldec Visit us at Nordbau - Stand West 121 right next to the main entrance. Other 3, 4 and 5 axle low loaders new and used available immediately

Condition: new, maximum load weight: 23,340 kg, overall weight: 30,000 kg, axle configuration: 3 axles, NEW VEHICLE Fliegl 3-axle flatbed lowboy trailer DTL - S - 300 Agrar, frame and chassis hot-dip galvanized Total weight: 24,000 kg / 30,000 kg Payload: 17,340 kg / 23,340 kg Unladen weight: 6,660 kg Overall length: 11,625 mm Platform length: 9,000 mm including 900 mm loading ramp Loading height: 900 mm Large set of lashing straps Drawbar 40 mm Tires 235 / 75 R 17.5", twin tires Without ABS, maximum permissible speed 60 km/h 12-volt electrical system, LED all-round light Ramps with spring-assisted lift, ramp length 2,800 mm Vehicle from current production – approximately 14 days lead time. Plus pre-carriage / preparation costs from warehouse Wiesmoor: €1,280.00 / net Lajdpfx Alellwhnsdsc Towing vehicle LoF, registered for agricultural or forestry use Lease-purchase offer: Term 48 months, residual value 40%, down payment only the VAT. Monthly installment: €599.00

Condition: new, maximum load weight: 34,310 kg, overall weight: 38,000 kg, axle configuration: 3 axles, total width: 2,550 mm, Vehicle / Body: Trailer, container chassis, semi-trailer Unladen weight: 3,690 kg Overall length: 13,500 mm Width: 2,520 mm Fifth wheel height approx.: 1,120 mm Further information: - 3-axle - Hot-dip galvanized frame including passivation - 1 x 45 ft with long gooseneck tunnel and angled front corners - 24-ton, 2-speed landing gear, single-sided operation - Aluminum side impact protection, galvanized steel underrun protection, extendable underrun protection for 45 ft containers - Plastic toolbox Lasdpfx Ajk N Acusldoc - Air suspension - 1st axle: automatic lift axle - Tires: 385/55 R22.5 - 2x 7-pin and 1x 15-pin sockets at the front From current production.

Condition: new, maximum load weight: 31,100 kg, overall weight: 40,000 kg, axle configuration: > 3 axles, loading space length: 10,410 mm, loading space width: 2,500 mm, loading space height: 900 mm, total width: 2,520 mm, Total weight: 24,000kg/40,000kg Empty weight: 8,900kg Payload: 15,100kg/31,100kg Total length: 11,940mm Loading length: 10,410mm total, 2,490mm offset, 7,920mm loading bed including rear bevel Width: 2,520mm Loading height: 900mm Further information plus pre-freight / provision from storage location 26639 Wiesmoor 1,280.00 €/net Steel welded construction Turntable with strong ball bearing ring Foldable rear support Wheel chocks with holder Aluminum side impact protection Rear splash guards across the entire width (not in conjunction with forklift bracket) Half-shell mudguards 1st + 2nd axle with anti-spray splash guards behind each axle, Anti-spray flaps in front of and behind the 3rd and 4th axle Excavator arm recess above the rear axles starting to the rear, approx. 1800 mm long, approx. 650 mm wide and approx. 150 mm deep, Lasdpfx Ajrducpjldoc 2 pairs of lashing holes each 5 tons. in the excavator arm recess on the side of the longitudinal frame approx. 300 mm from the front and approx. 200 mm in front of the rear bevel 1 plastic tool box, w=600 / h=425 / d=460 mm, lockable 1 storage box embedded in the floor on a crank with lid, W=720 mm/ L=520 mm / D= 170 mm Extensions extendable to 3,000 mm (not in the rear bevel) (The track width of the construction machines or vehicles to be transported must not exceed the outer frame width 2,550 mm) Storage compartment for wooden planks below the low-loading area Wooden planks 70 mm for widening to 3,000 mm Lashing eyes for low-loader 1 pair of lashing cutouts in the longitudinal beam at the front on a crank, 10 tons each. 4 pairs of lashing holes in the outer frame, each with 5 tons (tension belt attachment) 9 pairs of lashing mushrooms, embedded in the outer frame at the top and sides, each with 10 tons 2 x at the front on the bend 7 x in the low bed First lashing eye 250 mm from the front and last max. 250 mm from the back, distance between the lashing eyes not greater than 1100 mm 3 additional pairs of folding lashing eyes, each with 10 tons 1 x on the bend (sticks out) 1 x at the beginning of the low bed, embedded inside on the longitudinal beams 1 x embedded in the floor behind the last axle Towbar with tested 50 mm towing eye Towbar height adjustment via spring Axles + suspension Drum brake axles, as selected by the manufacturer "Laser-measured axle/chassis" Reduction in tire wear and fuel consumption Parabolic suspension with maintenance-free Steel-rubber bearings and mechanical axle load compensation at the front and rear (rocker compensation) Wheels and tires 235 / 75 R 17.5" at the manufacturer's discretion Steel rims in twin arrangement, factory silver Brake system 2-line compressed air brake system Spring-loaded parking brake 2 interchangeable coupling heads at the front, with connecting lines to the towing vehicle, 24 volt ABS and ALB, with ABS plug at the front, with connecting cable Caution: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrics 12-24 volts, multi-chamber LED lights, yellow LED lighting on the side, license plate lighting in LED, (Note! Incorrect diagnoses can occur with certain towing vehicles, although the function is present) 2 white position lights at the front in LED 2 white/red lane keeping lights at the rear in LED 2 x 7-pin, interchangeable plugs at the front, with connecting cable, 1 LED rotating beacon with holder, switched via parking light (light removable) 2 pairs of warning signs with double LED lighting and extendable

Condition: new, maximum load weight: 8,840 kg, overall weight: 11,800 kg, axle configuration: 2 axles, loading space length: 6,200 mm, loading space width: 2,480 mm, loading space height: 900 mm, total width: 2,550 mm, New Fliegl tandem low-loader with ramps type TPS 118 Chassis fully hot-dip galvanized - side walls aluminum Vehicle from current production - Delivery time approx. two weeks Gross weight: 11,800 kg Unladen weight: 2,960 kg Payload: 8,840 kg Overall length: 8,000 mm Loading length: 6,200 mm incl. rear slope Width: 2,550 mm Loading height: 900 mm Additional information plus pre-shipping / provision ex stock 26639 Wiesmoor €1,280.00 / net Loading width: 2,480 mm Chassis: central axle trailer Fine-grain steel welded construction Outer frame slightly sloped, new version with 'Load-lock profile' for lashing strap hooks 3 pairs of lashing rings on the outside floor, 5 t each 1 x front in the corners, 1 x before and 1 x in rear slope at the back Pair of lashing rings on outside floor/frame, 5 t each Support leg at the front Folding rear support 2 wheel chocks with holder Aluminum side underrun protection Galvanized steel rear underrun protection Full-width rear mudflap (not in combination with forklift holder) Quarter shell mudguards 1 plastic toolbox, w=600 / h=425 / d=460 mm, lockable Drawbar system central axle trailer Drawbar with certified 40 mm towing eye Drawbar height adjustable via spindle, max. adjustment range 300 mm Axles & suspension GFA axles with tapered roller bearings and S-cam brake 'Axles/chassis laser-measured' Reduces tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load equalization (rocker compensation) Braking system 2-line compressed air braking system Color-coded pipe routing for easy service. Hand spindle parking brake 2 error-proof coupling heads in front, with connection lines to tractor unit, 24 volt ABS and ALB, with ABS plug in front, with connecting cable, Note: The trailer may only be towed by towing vehicles that ensure the ABS function! Wheels and tires 4 x 235/75 R17.5 make at the manufacturer’s choice 4 steel rims, factory silver Electrics 24 volt, multi-chamber lights, side yellow LED lighting 2 white LED positioning lights front 2 white/red marker lights rear 2 x 7-pin error-proof connectors at front, with connection cable, Floor Steel/chequer plate floor for high point load capacity Note: Slight floor warping possible due to welding distortion! Platform length approx. 6,200 mm Rear slope approx. 900 mm Laodpov E Dqlefx Aldoc Front bulkhead / corner posts 25 mm aluminum hollow section, 400 mm high, Side walls 25 mm aluminum hollow section, 400 mm high, foldable and removable Central stanchions 1 pair of folding stanchions at side wall height, foldable and removable Rear wall / rear corner posts 1 pair of steel stanchions fixed to the frame with support for ramp locking. Entry width approx. 2,430 mm Ramps 2 steel ramps 2,300 mm long, 510 mm wide, laterally adjustable with hand grip on the ramps covered with wood (tipped with steel/chequer plate) with gas spring assist for single-person operation Painting Frame hot-dip galvanized including passivation '15-year warranty against rust-through' Front bulkhead RAL 9006 white aluminum Side wall RAL 9006 white aluminum Ramps hot-dip galvanized Lease-purchase offer: Term 48 months, down payment only VAT, final residual value 40%, monthly rate EUR 350.00

Condition: new, maximum load weight: 26,100 kg, overall weight: 35,000 kg, axle configuration: 3 axles, loading space length: 9,200 mm, loading space width: 2,520 mm, loading space height: 900 mm, total width: 2,550 mm, Vehicle / Body: Low loader semitrailer First registration: New vehicle Gesamtgewicht: 35.000kg/47.000kg Unladen weight: 8,900kg Payload: 26,100kg/38,100kg Overall length: 13,300mm Loading length: 9,200mm Width: 2,520mm Loading height: 900mm Further information Chassis low loader semi-trailer Welded steel construction, fifth wheel plate with interchangeable 2" kingpin and 2 kingpin positions (not in conjunction with forced steering) 24 t. 2-speed support winch, single-side operation, with straight lower section, without thrust compensation Folding rear support 2 wheel chocks with holder Aluminum side collision protection Rear spray flaps across the entire width Spray flaps in front of 1st axle and rear of each axle with anti-spray, according to EC 1 plastic tool box, w=600 / h=425 / d=460 mm, lockable Widenings extendable to 3,000 mm (not in rear slope) (However, the track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Storage compartment for wooden planks on gooseneck, front transverse Wooden planks 70 mm for widening to 3,000 mm Excavator trough above the rear axles starting to the rear, approx. 3,000 mm long, approx. 650 mm wide and approx. 230 mm deep, 2 pairs of lashing holes, 5 tons each, in the excavator trough on the side of the longitudinal frame approx. 300 mm from the front and approx. 200 mm in front of the rear slope Low loader lashing eyes 11 pairs of lashing mushrooms at the top and sides of the outer frame, 10 tons each 2 x on gooseneck 9 x distributed in the flatbed 2 pairs of lashing eyes at the front on the gooseneck, 5 tons each 3 pairs of swivel lashing eyes on the gooseneck, 5 tons each 2 pairs of additional hinged lashing eyes recessed into the flatbed, 10 tons each 1 x at the start of the low loading area 1 x at the end of the rear slope 1 pair preparation on incline of gooseneck for 6.7 to. screw lashing eye (JDT) 8 pairs of ring lashing eyes embedded in the outer frame, 5 tons each (can be converted to stake pockets) 1 pair of screw lashing eyes, 6.7 tons each (JDT), with large flange plate incl. thread as counterholder Axles + suspension SAF or BPW drum brake axles, manufacturer's choice "Axle/chassis laser-measured" Reduction of tire wear and fuel consumption Last axle self-steering, with automatic reverse lock via reversing light, and additional locking function on the vehicle via hand button. Air suspension Wheels and tires 235 / 75 R 17,5" at the manufacturer's choice Twin steel rims, factory silver Brake system 2-line compressed air brake system Colored cable routing for easy servicing. Spring-applied parking brake 24 volt EBS, electronic brake system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS Lodpfx Alsut Idnsdoac guaranteed! 2 swap-proof coupling heads at the front, without connecting cable with lifting & lowering valve Axle load detection via EBS-Canbus signal, for indication via display in the driver's cab, truck must be prepared accordingly truck must be prepared accordingly, no truck installation (no calibrated scales) Vehicle - driving stability system Tire pressure monitoring system according to ECE R 141, indication via display in towing vehicle, via EBS, without truck installed (prerequisite for this must be provided in the truck) Electrical system 24 volt, multi-chamber lights, amber LED lighting on the side Side amber LED ligh

Condition: new, maximum load weight: 18,400 kg, overall weight: 24,000 kg, axle configuration: 3 axles, loading space length: 5,900 mm, loading space width: 2,500 mm, loading space height: 860 mm, total width: 2,520 mm, Gross weight: 24,000kg / 30,000kg Tare weight: 5,600kg Payload: 18,400 / 24,400kg Total length: 10,290mm Loading length: 5,900mm including rear incline Width: 2,520mm Loading height: 860mm Further information plus pre-carriage / preparation ex storage location 26639 Wiesmoor €1,280.00 / net Chassis Lowbed Trailer Steel welded construction Turntable with heavy-duty ball-bearing slewing ring Rear supports foldable 2 wheel chocks with holder Rear mudflaps across entire width (not compatible with forklift holder) 1 plastic toolbox, w=600 / h=425 / d=460 mm, lockable Prepared for extensions to 3,000 mm (holes in outer frame with cover, not in the rear incline) Lashing points low loader 1 pair lashing cutouts in front longitudinal beam embedded in the goose neck, each 10t 7 pairs of lashing mushrooms recessed into the outer frame, each 10t (top and side) 1x at the front on the goose neck Lasdpfoynvrwex Aldec 5x in the lowbed 1x in the rear incline 12 pairs of lashing holes in the outer frame, 5t each (for securing straps) 5x on the goose neck, 6x lowbed, 1x rear incline Drawbar turntable coupling Drawbar with certified 40 mm towing eye Drawbar height adjustment by spring Axles & suspension Drum brake axles, according to manufacturer's choice "Axles/chassis laser-measured" to reduce tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bushings and mechanical axle load equalization (rocker equalization) Wheels and tires 235/75 R 17.5'' manufacturer's selection Steel rims in twin arrangement, factory silver Braking system 2-line compressed air braking system Spring-loaded parking brake 2 foolproof coupling heads at the front, with connecting lines to the towing vehicle, lines extended by approx. 60 cm without ABS, but with mechanical ALB, then max. 60 km/h approval Electrics 12 Volt, multi-chamber lamps, without side yellow LED lighting, side reflectors 2 white position lights at front 2 white/red marker lights at rear 1x 7-pole 12 Volt plug at front, with extension cable, extended by approx. 60 cm 1 LED beacon with holder, switched via parking light (removable beacon) 2 pairs of warning boards, illuminated and extendable to 3,000 mm Floor Gooseneck area with steel / checker plate covering Toolbox recessed into transition to goose neck then approx. 70 mm softwood floor, steel/checker plate covering in wheel arch area Rear incline with 70 mm softwood floor Lowbed area incl. rear incline 5,900 mm Loading ramps Steel ramps approx. 3,000 mm long, 750 mm wide, laterally slidable covered with wood (tip area steel/checker plate) Hydraulically operated via tractor PTO with throttle, control on driver’s side left Hydraulic connection with SVK plug NW 10/3, incl. connecting hose Operating instructions For 10,000 kg axle load, exemption required, indivisible load only!!! The specified gross weight is technically feasible, depending on cargo the gross weight may not be achievable due to axle/support/kingpin load limits. (Poor driving and tracking behavior due to incorrect load distribution possible) Country of registration / Plates Registration country: Germany with Dekra approval and certificate, for max. 60 km/h registration, towing vehicle LoF (agriculture/forestry), (Switzerland: max. 40 km/h possible) prepared for two-line license plate holder without contour marking / reflective tape per ECE R 048 Paintwork Frame hot-dip galvanized incl. passivation “15-year warranty against through corrosion” (text incomplete)

Condition: new, maximum load weight: 31,920 kg, overall weight: 40,000 kg, axle configuration: > 3 axles, loading space length: 10,410 mm, loading space width: 2,500 mm, loading space height: 900 mm, total width: 2,550 mm, New Fliegl 4-Axle Lowbed Trailer with Ramps, Model VTS 400 Gross weight: 24,000 kg / 40,000 kg Unladen weight: 8,080 kg Payload: 15,920 kg / 31,920 kg Total length: 11,940 mm Loading length: approx. 10,410 mm total, gooseneck approx. 2,490 mm, loading platform incl. rear chamfer approx. 7,920 mm Width: 2,550 mm Loading height: 900 mm Additional information: Plus delivery/preparation ex stock 26639 Wiesmoor €1,280.00 net Chassis - Lowbed Trailer Steel welded construction Turntable with heavy-duty ball bearing slewing ring Foldable rear supports 2 wheel chocks with holders Lodpfjxrx Nlox Aldoac Side underrun protection - aluminum Full-width rear mudflap Half-shell fenders on 1st and 2nd axles with anti-spray flaps behind each axle Anti-spray flaps in front of and behind 3rd and 4th axles Excavator arm recess above the rear axles extending to the rear, approx. 1,800 mm long, approx. 650 mm wide, approx. 150 mm deep 2 pairs of lashing holes (5 t rating each) in the excavator recess, on the longitudinal frame approx. 300 mm from the front and approx. 200 mm before the rear chamfer 1 plastic toolbox (W=600 mm, H=425 mm, D=460 mm), lockable Storage box flush-mounted in floor on the gooseneck, with lid (W=720 mm, L=520 mm, D=170 mm) Extendable widening beams to 3,000 mm (not at rear chamfer) (Note: Maximum track width of construction machines or vehicles must not exceed outer frame width of 2,550 mm) Stowage compartment for wooden planks under the lowbed deck Wooden planks 70 mm wide for extension to 3,000 mm Lashing points - Lowbed 1 pair of recessed lashing cutouts in front longitudinal beam on gooseneck, each rated 10 t 4 pairs of lashing holes in outer frame, each rated 5 t (for attaching tie-down straps) 9 pairs of lashing pins installed flush on top and side of outer frame, each rated 10 t 2 x front on gooseneck 7 x in the lowbed First lashing point 250 mm from front, last max. 250 mm from rear, distance between points no greater than 1,100 mm 3 additional pairs of folding lashing rings, each rated 10 t: 1 x on gooseneck (protruding) 1 x at the start of the lowbed, inset into the longitudinal beams 1 x recessed in floor behind the last axle Towing Arrangement – Turntable Trailer Drawbar with certified 50 mm towing eye Drawbar height adjustable via spring Axles & Suspension Drum brake axles, manufacturer’s choice "Axle/chassis laser alignment" for minimizing tire wear and fuel consumption Air suspension with raise/lower valve and auto-reset function Wheels & Tires 235/75 R 17.5", manufacturer’s choice Steel rims with twin arrangement, factory silver Brake System 2-line compressed air brake system Spring-applied parking brake Axle load detection via EBS CAN bus signal for display in the truck cab (truck must be pre-equipped; not a calibrated scale) Vehicle – Driving Stability System 2 foolproof coupling heads at front with connecting lines to tractor unit 12-24 Volt EBS, electronic braking system with EBS plug at the front and connection cable (Knorr brand) Note: The towed trailer may only be towed by tractors that guarantee the effectiveness of the ABS! Electrical System 12-24 Volt, multi-chamber LED lights, side yellow LED lighting, LED license plate lighting (Note: Certain tractor units may indicate malfunctions even if all functions are working) 2 white LED position lights at front 2 white/red LED lane marker lights at rear 2 x 7-pin foolproof connectors at front with connection cable 1 LED beacon with holder (switchable via parking lights; lamp removable)