Used Fliegl Three-Way Tipper Trailers for sale (327)

Condition: new, functionality: fully functional, empty load weight: 4,780 kg, maximum load weight: 33,220 kg, overall weight: 38,000 kg, axle configuration: 3 axles, total length: 11,250 mm, total width: 2,550 mm, suspension: air, tire size: 385/55 R22,5", tire condition: 100 %, Customized Transport Solution Configure your Fliegl vehicle to meet your requirements. The vehicle shown is an example. Production and equipment are tailored to individual customer needs. Chassis, Saddle, and Container Fine-grain steel welded construction, saddle plate with 2 replaceable kingpins and 2 kingpin positions Container mounts: Rear extension retracted: 1 x 20 ft, flush at the rear, low saddle load Rear extension extended, 1st stage: 1 x 30 ft, 2 x 20 ft, 1 x 40 ft with gooseneck tunnel Rear extension extended, 2nd stage: 1 x 45 ft with short gooseneck tunnel and overload to the rear Rear extension extended, 2nd stage + front extension, 1st stage: 1 x 45 ft with long gooseneck tunnel and angled corners with height adjustment at the rear and folding center supports for containers without a tunnel Container guide at the front, pluggable and removable Plug adapter for front locking, to lock containers without a tunnel from below, with holder when not in use Front extension on rollers, manually extendable (for 45 ft containers with long tunnels) Rear extension on rollers, with hand crank 24 ton, 2-speed support winch, single-sided operation 2 chock blocks with holder Aluminum side impact protection Galvanized steel underrun protection Extendable underrun protection for 45 ft containers Half-shell fenders with anti-spray flaps according to EG Rear impact protection Axles and Suspension SAF disc brake axles with 430 mm disc diameter Axle/chassis laser-aligned, reducing tire wear and fuel consumption Offset axle spacing mm (combined transport), up to 44 tons gross vehicle weight Air suspension 1st axle: automatic lift axle, including forced lowering and start-up assistance, activated by 3x braking (start-up assistance is functional up to an axle load exceeding 30% and up to a speed of max. 25 km/h) Braking System 2-line pneumatic braking system, color-coded lines for easy servicing Spring-loaded parking brake 2 fail-safe coupling heads at the front, without connecting line EBS, Electronic Braking System with EBS socket at the front, without connecting cable Note: The trailer may only be towed by tractor units that guarantee the effectiveness of the ABS! with lift and lower valve + auto-reset function Vehicle - Driving Stability System Axle load detection via EBS-Canbus signal, for display on the display in the driver's cab, the truck must be appropriately prepared Wheels and Tires Godpfx Aji Rizujhvjui 385/55 R22.5, manufacturer's choice Steel rims, factory silver Electrical System 24 Volt, multi-chamber lights, yellow LED lighting on the side 2 white position lights at the front 2 white/red side marker lights at the rear 2 x 7-pole fail-safe sockets at the front Operating Instructions Special permit required if the overall train length exceeds 16,500 mm. When transporting 45 ft containers with a short tunnel, with or without a front extension, the permissible system length from kingpin to the rear edge of the vehicle and the overall train length of 16,500 mm will be exceeded! The underrun protection must be manually extended! An exemption permit according to § 70 StVZo is required! Approval / Signage Germany Type approval according to EG 2007/46 24/7 service hotline prepared for single-row license plate holder Warning sign according to ECE - 70 Contour marking with reflective tape

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 3,980 kg, overall weight: 35,000 kg, axle configuration: 3 axles, loading space width: 2,420 mm, loading space height: 1,450 mm, loading space volume: 25 m³, total length: 8,600 mm, total width: 2,550 mm, total height: 3,240 mm, suspension: air, tire size: 385/65 r22.5, tire condition: 100 %, Customized transport solution Configure your Fliegl vehicle according to your requirements. The vehicle shown is an example. Production and equipment are tailored to individual customer needs. More information Chassis Fine-grained steel welded construction, lightweight design, kingpin plate with 2 interchangeable kingpins Curved front end, patented without support leg Wheel chocks + holder Underrun protection, foldable Semi-shell fenders integrated fender holder, surface resistant to stone chipping Towing hook at the rear Axles + Suspension SAF disc brake axles Axle/chassis laser-measured to reduce tire wear and fuel consumption Air suspension 1st axle automatic lift axle, incl. forced lowering and starting assist, actuated by 3x brakes (starting assist functional up to an axle load exceedance of 30% and a speed of max. 25 km/h) Hot-dip galvanized lift axle mechanism Braking system 2-line compressed air braking system, color-coded lines for easy servicing Spring-loaded parking brake 2 tamper-proof coupling heads at the front, without connecting line EBS, electronic braking system with EBS socket at the front, without connecting cable with lifting and lowering valve Vehicle driving stability system Wheels & tires 385/65 R22.5, manufacturer's choice Polished aluminum rim, manufacturer's choice Electrical system 24 Volt, multi-chamber lights, yellow LED lighting on the sides 2 white position lights at the front Gsdpfsi Ri H Ssx Ahvjui 2 white/red side marker lights at the rear 2 x 7-pin socket at the front, without connecting cable Hydraulics Low-pressure cylinder max. 170 bar, smallest stage hard chrome plated, with HDK screw connection, fixed part, NW 48 mm. Actuation via hydraulic system connected to the truck's auxiliary drive Tippers Sloping front wall 5 mm thick, with external side walls made of 30 mm hollow chamber profiles, neatly welded, with upper edge profile to prevent material spillage. Inside with a ladder on the front wall Shovel and broom holder on the outside of the front wall Greenline - conical and aerodynamic tipper body shape Membrane - rear wall Rear wall as a hinged flap with double-joint hinge, externally supported with a double hook lock. Rear wall with rubber seal Note! Heat resistant up to max. 170°C! Floor continuously 5 mm thick, Brinell 110 Note! Only for the transport of sand, gravel and rolled gravel with max. grain size up to 20 mm! All other transport goods are excluded from the warranty! Standing platform with ladder, connection plate for air/electric and brake with large clearance for best possible operation. Rollover tarpaulin, one-sided for laying down on the right-hand side, with central locking on the left-hand side Operating instructions For the transport of salt, lime, etc., we recommend a tipping cylinder with a hard-chrome plated piston rod to protect against rust The specified total weight is technically possible, depending on the cargo, the total weight may not be reached while observing the permissible axle/support and saddle loads. (Poor driving and handling behavior due to incorrect load distribution possible) Country of approval/ Signage Germany with Dekra approval and certificate (according to §13 EG - FGV) 24/7 service hotline prepared for single-line license plate holder Contour marking with reflective strips according to ECE R 048, white on the sides and red at the rear Paintwork Frame DB 7350 Novagrau Tipper body R

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 14,300 kg, maximum load weight: 9,700 kg, overall weight: 24,000 kg, axle configuration: 3 axles, loading space width: 2,520 mm, loading space height: 900 mm, total length: 12,000 mm, total width: 2,550 mm, suspension: air, tire size: 235 / 75 r 17,5, tire condition: 100 %, Customized Transport Solution Configure your Fliegl vehicle to meet your requirements. The vehicle shown is an example. Production and equipment are customized according to customer specifications. Further Information Chassis Steel welded construction Turntable with robust ball bearing Foldable rear support 2 wheel chocks + holder Aluminum side underrun protection Splash guards at the rear over the entire width Quarter panel fenders in front of the 1st axle Excavator arm recess starting above the rear axles to the rear, approx. 1800 mm long, approx. 650 mm wide and approx. 150 mm deep, 2 pairs of lashing points of 5 tons each in the excavator arm recess on the side of the longitudinal frame, approx. 300 mm from the front and approx. 200 mm in front of the rear slope 1 storage box recessed in the gooseneck in the floor with a lid, W=720 mm/ L=520 mm / D= 170 mm 1st pair of wheel recesses recessed in the gooseneck in the low-loader wheel well area, sloped for access, length at the bottom approx. 1600 mm, approx. 400 mm deep. Note! Frame in the main beam area is 400 mm higher than the wheel recess. 2nd pair of wheel recesses between the axles recessed in the low-loader in the wheel well area, sloped for access, length at the bottom approx. 600, approx. 300 mm deep. Note! Frame in the main beam area is 300 mm higher than the wheel recess. Wheel recess cover pull-out from the main frame, with wood inserts. Distance from the outer frame, beam to beam, approx. 1280 mm Extensions pull-out to 3,000 mm, foldable at the wheel recess extensions (extension not in the rear slope and not in the wheel recesses at the bottom) Storage compartment for wooden planks in the middle of the loading area or under the loading area, depending on technical feasibility Wooden planks 70 mm for extension to 3000 mm Lashing points, low-loader 1 pair of ring lashing points recessed at the front on the gooseneck, each 5 tons 8 pairs of lashing eyes at the top and on the side recessed in the outer frame, each 10 tons 2 x at the front on the gooseneck 6 x in the low-loader, the first lashing point 250 mm from the front and the last one max. 250 mm from the rear, the distance between the lashing points is no more than 1100 mm 5 pairs of ring lashing points recessed in the outer frame, each 5 tons (can be converted to stake pockets) Coupling system, trailer, turntable Drawbar with tested 50 mm drawbar eye with 8° inclined drawbar eye Axles + Suspension SAF drum brake axles Axle/chassis laser-aligned, reducing tire wear and fuel consumption Air suspension with lifting and lowering valve, can be operated separately at the front and rear Wheels and tires 235/75R17.5 according to manufacturer's choice Steel rims in twin arrangement, factory silver Braking system 2-line compressed air brake system Spring-loaded parking brake Trailer Info Center for displaying vehicle data such as axle load (no calibrated scale) and odometer Axle load detection via EBS-CAN bus signal, for display on the display in the cab, truck must be suitably prepared, no truck installation (no calibrated scale) Vehicle-driving stability system Gedpfx Aei Ri I Nehvjui Duomatic connection at the front, with connecting cable to the towing vehicle EBS, Electronic Braking System with EBS plug at the front, with connecting cable Note: The trailer may only be towed by towing vehicles that ensure the effectiveness of the ABS! Electrical system 24 Volt, multi-chamber lights in LED with resistor, yellow LED lighting on the side, license plat

Condition: new, machine/vehicle number: Produktpalette, empty load weight: 3,950 kg, maximum load weight: 31,050 kg, overall weight: 35,000 kg, axle configuration: 3 axles, loading space length: 7,200 mm, loading space width: 2,420 mm, loading space height: 1,450 mm, loading space volume: 25 m³, total length: 8,600 mm, total width: 2,550 mm, total height: 2,930 mm, suspension: air, tire size: 385/65r22.5, tire condition: 100 %, Customized transport solution Configure your Fliegl vehicle according to your requirements. The vehicle shown is an example. Production and equipment are tailored to individual customer requirements. More information: Chassis Fine-grained steel welded construction, lightweight design, kingpin plate with 2 interchangeable kingpins Curved front end, patented Telescopic support in the center, cannot be uncoupled with load, in the uncoupled state, the vehicle must stand at an angle towards the rear. Gedoi Ri R Ijpfx Ahvsui 2 chock blocks + holder Underrun protection, foldable Semi-shell fenders Integrated fender holder, surface repels stones with anti-splash flaps on the last axle 1 tarpaulin rod + holder 2 towing hooks at the rear Axles + suspension SAF disc brake axles with 430 mm disc diameter Axle/suspension laser-aligned to reduce tire wear and fuel consumption Axles in off-road design Air suspension 1st axle automatic lift axle, incl. forced lowering and start-up assist, operated 3x by braking (start-up assist functional up to an axle load exceedance of 30% and a speed of max. 25 km/h) Hot-dip galvanized lift axle mechanism Braking system 2-line pneumatic braking system, color-coded lines for easy servicing Spring-loaded parking brake 2 non-interchangeable coupling heads at the front, without connection line EBS, electronic braking system with EBS socket at the front, without connection cable Attention: Trailer may only be pulled by towing vehicles that guarantee the effectiveness of ABS! with lifting and lowering valve Vehicle driving stability system Automatic tilting lowering with shut-off valve Wheels & tires 385/65R22.5, manufacturer's choice Steel rims, factory silver Electrical system 24 Volt multi-chamber lights, yellow LED lighting on the side 2 white position lights at the front 2 white/red marker lights at the rear 2 x 7-pole non-interchangeable sockets at the front, without connection cable Hydraulics Low-pressure cylinder max. 170 bar, smallest stage hard-chromed, with HDK screw fitting, fixed part NW 48 mm. Actuation via truck auxiliary drive Tipping body Aluminum box body, sloping front wall 5 mm thick, 30 mm hollow chamber profiles, cleanly welded, with top rail profile that prevents bulk material from spilling. Inside with ladder on the front wall. Shovel and broom holder on the outside of the front wall. Greenline - conical and aerodynamic tipping body shape Membrane - rear wall Rear wall as a hinged flap with double hinge, externally mounted with a double hook lock. Rear wall with rubber seal. Note! Heat resistant up to max. 170°C! Floor continuously 6 mm thick Standing platform with ladder, connecting plate for air/electricity and brake with large clearance for best possible operation. Roller cover on one side for storage on the right, with central locking on the left. Operating instructions For the transport of salt, lime, etc., we recommend a tipping cylinder with a hard-chromed piston rod, so that it is not attacked by the material and does not rust. The stated total weight is technically possible, but depending on the load, the total weight may not be reached while observing the permissible axle/support and kingpin loads. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of approval/signage Germany Type approval according to EC 2007/46 24/7 service hotline prepared for license plate holder, single row Contour marking with reflective tape according to ECE R 048, white on the sides and red at the

Condition: used, functionality: fully functional, machine/vehicle number: WFDFLT22701003408, empty load weight: 4,800 kg, maximum load weight: 22,200 kg, overall weight: 27,000 kg, axle configuration: 2 axles, first registration: 01/2015, next inspection (TÜV): 02/2027, loading space length: 13,650 mm, loading space width: 2,480 mm, total length: 13,850 mm, total width: 2,550 mm, suspension: air, tire size: 385/55 R19,5", color: red, Please note: The images shown are archive photos. The vehicle may still be in operation at the time of inquiry. # 2-Axle Fliegl Mega Platform Semi-Trailer ## Weights & Dimensions * Gross Vehicle Weight (GVW): 27,000 kg * Payload (approx.): 22,200 kg * Axle load: 16,000 kg * Kingpin load: 11,000 kg * Unladen weight (approx.): 4,800 kg (± manufacturing tolerance) * Overall length: approx. 13,850 mm * Overall width: max. 2,550 mm * Overall height: approx. 2,245 mm * Platform length: approx. 13,650 mm * Platform width: approx. 2,480 mm * Fifth wheel height: approx. 950 mm * Kingpin setting: approx. 1,680 mm * Front corner radius: approx. 2,040 mm --- ## Chassis – Mega Platform Semi-Trailer * High-tensile fine-grain steel welded chassis construction * Fifth wheel plate with replaceable 2" king pin * 13 pairs of recessed lashing rings integrated into the outer frame, each rated at 2.5 tonnes * Outer frame with integrated Load-Lock profile for quick attachment of lashing straps * 24-tonne two-speed landing gear, single-side operation, straight foot design, without thrust compensation * Wheel chocks with holders * Aluminium side underrun protection * Steel rear underrun protection * Quarter mudguards --- ## Axles & Suspension * 1st axle: SAF drum brake axle * 2nd axle: BPW drum brake axle * Air suspension --- ## Braking System * Dual-line compressed air braking system * Spring-loaded parking brake * Two non-interchangeable coupling heads at the front (without connecting hoses) * EBS (Electronic Braking System) with front EBS socket, without connecting cable * Integrated raise-and-lower valve * Vehicle Stability Control System Note: The trailer may only be operated with towing vehicles that ensure proper ABS functionality. --- ## Wheels & Tyres * 385/55 R19.5 tyres (manufacturer's choice) Gedpfx Ahoy Sk U Ajvjui * Steel rims, factory silver finish --- ## Electrical System * 24 V electrical system * Multi-chamber rear lights * Yellow LED side marker lights, recessed as far as possible for maximum protection * 2 white front position lights * 2 white/red rear outline marker lights * 2 × 7-pin front sockets, without connecting cables --- ## Platform * Approx. 30 mm phenolic-coated plywood floor * Omega-reinforced cross joints * Longitudinal subframe supports for high point-load capacity * Suitable for forklift axle loads up to 7,100 kg Note: Minor floor distortion due to weather conditions is possible. --- ## Front Wall * Front wall, approx. 1,200 mm high * Heavy-duty steel corner posts in volume specification * Integrated inspection windows --- ## Registration & Compliance * Registration country: Germany * DEKRA inspection and certification included * 24/7 service hotline * Prepared for single-line licence plate holder * Rear warning plate according to ECE R70 * Reflective contour markings according to ECE R048 (white on the sides, red at the rear) --- ## Paint Finish * Chassis: RAL 3002 Carmine Red * Landing gear: black coated * Front wall: RAL 3002 Carmine Red --- Please note: The images shown are archive photos. The vehicle may still be in operation at the time of inquiry.

Condition: used, functionality: fully functional, machine/vehicle number: WFDFLT33902037031, empty load weight: 4,795 kg, maximum load weight: 30,320 kg, overall weight: 35,000 kg, axle configuration: 3 axles, first registration: 09/2025, loading space length: 7,200 mm, loading space width: 2,470 mm, loading space height: 1,450 mm, loading space volume: 25 m³, total length: 8,600 mm, total width: 2,550 mm, total height: 3,040 mm, suspension: air, tire size: 385/65 R22.5", tire condition: 100 %, color: grey, These images are archive images! The vehicle may still be in use! Fine-grain steel welded construction, in basic lightweight design, kingpin plate with replaceable 2" kingpin, Curved front end "Patented" 24-ton, 2-speed landing gear, single-sided operation, with semi-circular lower part and straight connection plate, with stroke compensation Support wedges with holder Underrun protection, foldable Half-shell fenders Integrated "fender holder," surface resistant to stone chipping with anti-splash flaps only on the last axle Tarpaulin rod with holder Towing hook at the rear (not on Revolution model) Axles + Suspension SAF disc brake axles with 430 mm disc diameter "Axle/chassis laser-aligned" – reduces tire wear and fuel consumption Axles in off-road design Air suspension 1st axle: automatic lift axle, including forced lowering and starting assistance, activated by "3x braking" (starting assistance is functional up to an axle load exceeding 30% and up to a speed of max. 25 km/h) "Hot-dip galvanized lift axle mechanism" Braking system 2-line compressed air braking system Color-coded line routing for easy maintenance Spring-loaded parking brake 2 fail-safe coupling heads at the front, without connecting line 24-volt EBS, electronic braking system with EBS socket at the front, without connecting cable Note: The trailer may only be towed by tractor units that ensure the effectiveness of the ABS! with lifting and lowering valve Vehicle - driving stability system Automatic tilting lowering with shut-off valve "TPMS" tire pressure monitoring system - display on the tractor unit, via EBS, without truck installation (the truck must have the necessary prerequisites. Only on base tires). Wheels and tires 385/65 R22.5" Steel rims Electrical system 24 volts, multi-chamber lights in LED, yellow LED lighting on the sides, license plate lighting in LED (Note! with certain tractor units, false diagnoses may occur, although the function is given) Yellow LED lighting on the sides linked to the turn signal "flashing side lights" 2 white position lights at the front in LED 2 white/red outline lights at the rear in LED 2 x 7-pole and 1 x 15-pole fail-safe sockets at the front, without connecting cable Additional LED work light, integrated and recessed at the rear, switched via reversing light Godpfx Ahey Rrplovsui Hydraulics Low-pressure cylinder max. 170 bar Operation hydraulically via truck auxiliary drive Bins Aluminum box body made of high-quality, abrasion-resistant material. Sloping front wall, 5 mm thick, with external cylinder mount. Side walls made of 30 mm hollow chamber profiles, cleanly welded, with top rail profile that prevents spillage. Inside with access ladder on the front wall (not in conjunction with Cramaro). Shovel and broom holder outside on the front wall. Greenline - conical and aerodynamic bin shape "Membrane" - rear wall Rear wall as a hinged flap with "double-hinge hinge," externally mounted with double hook lock. Rear wall with rubber seal Floor continuous, 6 mm thick Standing platform with access ladder, connecting plate for air/electrical and brake connections with large clearance for optimal operability. Roll tarp, can be folded to the right side, with central locking on the left side Operating instructions For transport of salt, lime, etc., we recommend a tipping cylinder with a hard-chrome plated piston rod, so that it is not attacked and rusted by the material.

Condition: used, maximum load weight: 6,740 kg, overall weight: 10,000 kg, axle configuration: 2 axles, first registration: 05/2015, next inspection (TÜV): 10/2025, loading space length: 6,500 mm, loading space width: 2,480 mm, loading space height: 2,950 mm, loading space volume: 47 m³, total width: 2,550 mm, total height: 4,000 mm, Equipment: ABS, Internal number: 3372 ----Phone & WhatsApp: ----Fliegl TKF 118 tandem trailer, SDAH tarpaulin and side rails, sliding curtain, rear portal doors, permissible gross weight: 10,000 kg, technically possible: 11,800 kg, payload: 6,740 kg / 8,540 kg. First owner. TÜV (technical inspection): 10/2025. ----ABS/EBS, air suspension, height-adjustable drawbar, tires: 235/75 R17.5, tire condition: 20-30%, Duomatic coupling, rear portal doors, aluminum outriggers, loading height approx. 850 mm. ---- * We sell exclusively subject to our General Terms and Conditions. Gujdpfx Aez Hzpushvsi * We assume no liability for errors in the vehicle description. * The vehicle may be covered with or have advertising affixed. * We sell used spare parts for DB and MAN, such as engines, transmissions, axles, cabs, and bodies. Cranes, hooklifts, etc. For detailed information, please contact us by phone or at:

Condition: used, Year of construction: 2025, Disc brakes, air suspension, ABS, EBS 3-axle 3-axle sliding floor semi-trailer, type SDS 390/101 X-tra Long - Permissible/technical total weight: 35000/39000 kg - Permissible/technical payload: approx. 27148/31148 kg - Permissible/technical aggregate load: 24000/27000 kg - Permissible/technical fifth-wheel load: 11000/12000 kg - Tare weight (base version): approx. 7852 kg +/- manufacturing tolerance - Overall length: approx. 15350 mm - Overall width max.: 2550 mm - Overall height: approx. 4005 mm - Internal length: approx. 14905 mm - Internal width: approx. 2470 mm - Internal height front: approx. 2655 mm - Internal height rear: approx. 2853 mm - Volume: approx. 101 cbm - Fifth wheel height: approx. 1130 mm - Kingpin mounting dimension: approx. 1640 mm - Front corner dimension: approx. 2040 mm Trailer chassis: - Fine-grained steel welded construction in lightweight design, up to the support legs Guodpfx Ahjz Np N Aovji - Fifth wheel with interchangeable 2" kingpin Tires (front): 385/55R22.5, Tires (rear): 385/55R22.5 = Further information = Year of manufacture: 2025 Tare weight: 35,000 kg General condition: good Technical condition: good Optical condition: good Please contact Ria Lange for more information.

Condition: used, axle configuration: 3 axles, first registration: 12/2022, loading space length: 9,600 mm, loading space width: 2,480 mm, loading space height: 2,050 mm, total length: 10,800 mm, total width: 2,550 mm, total height: 3,700 mm, suspension: air, tire size: 385/65R52,25, color: other, Equipment: ABS, = Additional Options and Accessories = - EBS = Remarks = Gjdpfszylb Rox Ahvsui Number of axles: 3, Tare weight: 5780 kg, Gross vehicle weight: 39000 kg, Chassis type: Complete chassis, Chassis material: Steel, Kingpin size: 2 inch, Suspension type: Full air suspension, ABS, EBS, Body construction year: 2022, Number of sides: 1 side, Tipper drive: PTO, Drum volume: 50, Drum volume in: m3, Axle type: SAF = Additional Information = General information Cab: Day cab License plate: KLEYN1 Powertrain Fuel type: Diesel Transmission Transmission: Manual gearbox Axle configuration Tire size: 385/65R52.25 Brakes: Disc brakes Suspension: Air suspension Axle 1: Lift axle; Tire tread depth left: 13 mm; Tire tread depth right: 13 mm Axle 2: Tire tread depth left: 8 mm; Tire tread depth right: 9 mm Axle 3: Tire tread depth left: 5 mm; Tire tread depth right: 7 mm Weights Tare weight: 5,780 kg Payload: 33,220 kg GVW: 39,000 kg Environment Emission standard: Euro 0 Maintenance APK (Technical Inspection): valid until 01.2027 Condition Overall condition: average Technical condition: average Optical condition: average Damage: none Financial information Leasing price: 529 € per month (default, 60 months); Please inquire for further information and conditions = Company Information = Kleyn Trucks is one of the world's largest independent dealers in used vehicles. Here you can choose from a constantly changing stock of 1200 used trucks, tractor units, and trailers. Our range includes all European brands from various years of manufacture and price ranges. Why buy from Kleyn Trucks? It's simple! • Large, rapidly changing stock • Recognizable quality • A good price • Honest business practices • We speak many languages • We understand our customers • Assistance with import and transport • (Export) registration is quickly arranged • Expert technical services • The security of "recognizable quality" • And more... Please visit our website for special offers and a complete inventory: Leasing through Kleyn Trucks is possible in most European countries! Quickly calculate your leasing rate and submit an inquiry via our website. Inquire directly about our European warranty package.

Condition: used, maximum load weight: 8,375 kg, overall weight: 12,000 kg, axle configuration: 2 axles, first registration: 10/2011, loading space length: 7,290 mm, loading space width: 2,480 mm, loading space height: 2,580 mm, loading space volume: 47 m³, total width: 2,550 mm, total height: 3,600 mm, Equipment: ABS, Flatbed with side sliding curtains, sliding tarpaulin cover, double-wing door with rotating rod locking mechanism at the rear, aluminum sideboards 500 mm high, screen-printed floor, lashing points, spare wheel holder under the body, SAF axle(s), drum brake system, air suspension with lifting and lowering mechanism, the vehicle can be fitted with advertising or lettering. SI87036 Gedozc Tipopfx Ahvoui Our offer generally does not include a new TÜV inspection. If a new TÜV inspection is desired, we will gladly provide you with a quote from our partner workshops! The vehicle can be fitted with advertising or lettering. Our general terms and conditions of delivery and payment apply. We would be happy to prepare a financing or leasing offer for this vehicle. Please contact us!

Condition: used, empty load weight: 6,075 kg, maximum load weight: 28,925 kg, overall weight: 35,000 kg, axle configuration: 3 axles, next inspection (TÜV): 03/2027, total length: 13,850 mm, total width: 2,550 mm, total height: 4,000 mm, suspension: air, tire size: 435/50 R19,5, color: red, Year of construction: 2023, Equipment: ABS, Color: RAL 3002 Carmine Red Front/rear panel: Purple / white Extension ladder at the rear, door latch on the side Support wedges with holder, aluminum side impact protection, galvanized steel underride protection, quarter panel fenders in front of the 1st axle and behind each axle, with anti-spray flaps behind each axle, rear impact protection, Pallet stop on both sides, approximately 15-20 mm high, in a bolted design, loading height is reduced by approximately 15-20 mm, plastic toolbox Axles + Suspension SAF disc brake axles, "axle/chassis laser measured" to reduce tire wear and fuel consumption, air suspension, 1st axle automatic lift axle, including forced lowering and starting assistance, Activation via "3x braking" (starting assistance is functional up to an axle load exceeding 30% and up to a speed of max. 25 km/h) Axle lift below the recommended ride height, therefore no warranty for tire damage Braking system 2-line compressed air braking system, color-coded lines for easy servicing, spring brake parking brake, 2 fail-safe coupling heads in front, without connecting line, EBS, electronic braking system with EBS socket in front, without connecting cable. Note: The trailer may only be pulled by towing vehicles that ensure the effectiveness of the ABS! with lifting and lowering valve Ride height in conjunction with lift axle, when the lift axle is raised, the loading or overall height increases by 50 mm (in Mega Flex only at low ride height or saddle height), vehicle - driving stability system Gedpfx Aszun I Aohveui Wheels and tires 435/50 R19.5", manufacturer's choice, steel rims, factory silver Electrical system 24 Volt, multi-chamber lights, yellow LED lighting on the side, 2 white position lights in front 2 white/red marker lights at the rear, 2 x 7-pole and 1 x 15-pole fail-safe sockets in front Floor Sieve-printed panels approximately 30 mm thick, on longitudinal supports for high point load capacity for forklift axle load up to max. 7100 kg Front wall / corner posts 2,580 mm high, corner posts steel in volume design, release device for side tarpaulin on front wall, "Crash-Blocker," bottom inside at approximately 140 mm height with steel impact protection Intermediate supports 3 pairs of sliding supports, fully adjustable in length, with 4-fold insertion pockets and a long pocket at the bottom, 3 pairs of support positions Insertion slats 5 rows of wooden insertion slats Rear wall / corner posts Corner posts at the rear, steel up to the lower edge of the roof, attachment for tarpaulin with round tube and tarpaulin tensioning ratchet Rear portal doors, 2-wing with 2 internal rotary rod locks each Tarpaulin Tarpaulin, with welded-in horizontal and vertical straps Tensioning closures made of stainless steel Roof Fliegl sliding roof, sliding cover, end lift at the rear that can be folded up, with a cover that can be slid from back to front, L-shaped roof beam for the automotive industry, inner width between the roof beams approximately 2,490 mm, tarpaulin color: white, roof non-elastic, little deflection of the roof beam during loading and unloading, EcoLift - lifting roof can be raised by approximately 380 mm, on both sides, with gas spring support, 3 driving positions in the front: interior height in the front approximately 2900mm/ 2950 mm / 3000 mm Optimal rain strip at the rear, on top of the end rail, above the doors Fliegl manufacturer certificate for body strength according to EN 12642 XL, Fliegl manufacturer certificate for body strength accor

Condition: used, first registration: 09/2016, color: other, Equipment: ABS, = Additional options and accessories = Gsdjz Eh N Espfx Ahvoui - BPW-Assen - Drum brakes - Lift Axle = Remarks = Fliegl, 2016, BPW axles, Axle 1 Liftable, Drum brakes = More information = Year of construction: 2016 = Dealer information = Bank data: Rabobank Account: 39.33.10.655 IBAN: NL73RABO0393310655 Swift code: RABONL2U - Always check our bank details before transaction! - Reservation of vehicles is not possible without a deposit. - Writing and text errors are reserved for all vehicles offered.

Condition: used, maximum load weight: 21,800 kg, overall weight: 27,000 kg, axle configuration: 2 axles, first registration: 07/2007, loading space length: 7,110 mm, loading space width: 2,310 mm, loading space height: 1,410 mm, loading space volume: 23 m³, total width: 2,550 mm, total height: 3,200 mm, Equipment: ABS, Internal number: 3652 ----WhatsApp: ----Fliegl ZHKA 240, dump truck, open box, aluminum, 2-axle tipping semi-trailer with front hydraulic system. ABS. ----ABS, SAF axles, air suspension, lift axle, drum brakes, tires: 385/65 R22.5, tire condition: 20-40%, ---- * We sell exclusively according to our General Terms and Conditions. Gujdpfjz Hzmysx Ahvsi * We assume no liability for errors in the vehicle description. * The vehicle may be covered with advertising and/or have lettering. * We sell used spare parts for DB and MAN, such as engines, transmissions, axles, cabs, and superstructures. Cranes, hooklifts, etc. For detailed information, please contact us by phone or at:

Condition: used, maximum load weight: 2,300 kg, overall weight: 3,000 kg, axle configuration: 2 axles, first registration: 06/2015, Ref. No.: B - 06 On behalf of customer Fliegl * TTS 30-30 * Low-bed trailer * Ramps Gjdpfx Aexvf U Nohveui * 2-axle * Permissible total weight 3000kg * Very good condition, little used Trade-in possible Financing starting at 3.99% Errors and prior sale excepted! The information in this advertisement is non-binding descriptions and does not constitute guaranteed characteristics. The seller assumes no liability for typographical or data transmission errors. Stated features should be checked separately. All details in the ads are non-binding! Nationwide delivery within Germany available upon request. Opening hours: Monday to Thursday from 9:00 am to 5:00 pm Friday from 9:00 am to 2:00 pm and by appointment!

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 4,750 kg, maximum load weight: 30,250 kg, overall weight: 35,000 kg, axle configuration: 2 axles, loading space length: 7,200 mm, loading space width: 2,350 mm, loading space height: 1,450 mm, loading space volume: 25 m³, total length: 8,600 mm, total width: 2,550 mm, total height: 3,000 mm, suspension: air, tire size: 385/65 R 22.5, tire condition: 100 %, Custom-made transport solution Configure your Fliegl vehicle according to your requirements. The vehicle shown is an example. Production and equipment are tailored to individual customer requirements. More information Chassis, semi-trailer, tipper Fine-grained steel welded construction, in basic lightweight design, turntable with interchangeable 2 kingpin Curved front end, patented 24 tons, 2-speed landing gear, single-side operation, with straight lower part, without thrust compensation Underrun protection, foldable Half-shell mudguards Towing hook at the rear Axles + suspension SAF disc brake axles with 430 mm disc diameter Axle/suspension laser-aligned to reduce tire wear and fuel consumption Axles in off-road design Air suspension 1st axle, automatic lift axle, including forced lowering and starting aid Hot-dip galvanized lift axle mechanism, 10-year warranty against rust-through Braking system 2-line compressed air braking system, color-coded lines for easy servicing Spring-loaded parking brake 2 fail-safe coupling heads at the front, without connection line EBS, electronic braking system with EBS socket at the front, without connection cable Note: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! With lifting and lowering valve Vehicle - driving stability system Guodpfxji Ri Nfo Ahvoi Wheels and tires 385/65 R22.5 Steel rims, factory silver "TPMS" tire pressure monitoring system according to ECE R 141, display via the display in the towing vehicle, via EBS, without truck installation (this must be available in the truck. Only for basic tires). Electrical system 24 volts, multi-chamber lights, yellow LED lighting on the side Yellow LED lighting on the side coupled with the turn signal "Flashing side lights" 2 white position lights at the front 2 white/red marker lights at the rear 2 x 7-pole fail-safe sockets at the front, without connection cable Hydraulics Low-pressure cylinder, max. 170 bar, smallest stage hard-chromed, with HDK screw connection, fixed part, NW 48 mm (without hose connection) Operation hydraulically via truck auxiliary drive Body Steel round body in Stone Master design made of highly wear-resistant HB 400/450 steel. Sloping front wall with externally mounted hydraulic cylinder with ladder on the front wall. Greenline - conical and aerodynamic body shape Shovel and broom holder on the outside of the front wall. Membrane - rear wall Rear wall as a swing gate with double hinge, externally mounted with double hook locking. 2 clamping screws with lever locks on the side below. Side walls continuous, 4 mm thick, floor 4/5 mm thick, wear-resistant and weight-optimized construction Standing platform with ladder, connection plate for air/electricity and brake with large space for best possible operation. Roll cover on one side for stowing on the right, with central locking on the left Country of registration/signs Germany With Dekra approval and certificate (according to §13 EG - FGV) Superstructure strength according to EN 12642 24/7 service hotline Prepared for license plate holder, single row Contour marking with reflective tape according to ECE R 048, white on the side and red at the rear Paint finish Frame DB 7350 Novagrau 10-year warranty against rust-through Support feet, black coated Body RAL, single color Roll cover RAL, single color Available in thermally insulated design!

Condition: used, overall weight: 38,000 kg, axle configuration: 3 axles, first registration: 11/2014, Year of construction: 2014, Equipment: ABS, Tipper with pump device 2x aluminum cabinets Pipe holder + pipes Godpfxszfyiyj Ahvjui 8x container mounts Drip tray Tread plate Good condition Input errors, amendments, mistakes, and prior sale excepted. The information given in our advertisements, online, on price tags, and in pictures constitutes non-binding descriptions and does not represent guaranteed characteristics. The seller assumes no liability for typing or data transmission errors.

Condition: used, maximum load weight: 14,500 kg, overall weight: 18,000 kg, axle configuration: 2 axles, first registration: 06/2019, total length: 9,950 mm, total width: 2,550 mm, total height: 1,450 mm, Equipment: ABS, Trailer for roll-off containers, galvanized, pneumatic container locking system, Duo-Matic coupling head, adjustable drawbar, ABS, EBS, SAF INTRA axle(s), disc brake system, air suspension with lift and lower mechanism, vehicle can be fitted with advertising or lettering. SI87444 Guodpfe Ahu Upox Ahvji Our offer generally does not include a new TÜV inspection. If a new TÜV inspection is desired, we will be happy to provide you with an offer from our partner workshops! The vehicle can be fitted with advertising or lettering. Our general terms and conditions of delivery and payment apply. We will gladly prepare a financing or leasing offer for this item. Please contact us!

Condition: used, maximum load weight: 29,980 kg, overall weight: 35,000 kg, axle configuration: 2 axles, first registration: 02/2021, loading space volume: 25 m³, Equipment: ABS, Fliegl SZS01 Tipping Trailer, 25 m³, Lift Axle, Tarp For inquiries: 0926778 * Condition: very good * First registration: 2021 * ABS * EBS * 2-axle, air-suspended * BPW axles * Lift axle Gedpozzgwpofx Ahvoui * Disc brakes * Platform at the front * Underrun protection, aluminum * Tarp Tires: 1st axle: 385 / 65 R 22.5, 25% air-suspended, lift axle 2nd axle: 385 / 65 R 22.5, 50% air-suspended ----Price: 17,900 EUR + 19% VAT For further questions, you can reach us on the following telephone numbers: * We speak: German, English, French, Polish, and...? Typographical errors, errors and prior sale excepted.

Condition: new, functionality: fully functional, machine/vehicle number: WFDFLT33902034305, empty load weight: 5,875 kg, maximum load weight: 33,125 kg, overall weight: 39,000 kg, axle configuration: 3 axles, loading space length: 13,650 mm, loading space width: 2,480 mm, loading space height: 2,790 mm, total length: 13,850 mm, total width: 2,550 mm, total height: 4,000 mm, suspension: air, tire size: 385/65 R22,5", tire condition: 100 %, color: original, Archive photos shown. Vehicle may still be in operation. Godpfszlrqcjx Ahvjui Fliegl Rail-Transport Curtainsider Semi-Trailer (Huckepack) High-strength fine-grain steel welded chassis with replaceable 2" kingpin. Rail-compatible Huckepack design for combined road/rail transport. EN 13044 railway coding with ILU code. XL rail load securing package for transport speeds up to 140 km/h, including 4 colour-marked crane grab areas, integrated grab protection in the curtain, roof markings for crane positioning, max. overall height 4,000 mm with air suspension lowered for pocket wagons. Foldable side and rear underrun protection, aluminium side guards, rear ladder, D-Lock door retainers, Heavy Blocker 2.0 rear impact protection, yellow ferry lashing rings and pallet stops on both sides. Axles & Suspension: SAF 430 mm disc brake axles for combined transport with anti-drop cable protection, air suspension, automatic lift axle with forced lowering and traction aid (activated by braking three times). Braking System: Dual-line air brake system with colour-coded air lines, spring parking brake, EBS with front socket, raise/lower valve with auto-reset function. Tyres: 385/65 R22.5 tyres (manufacturer's choice), steel wheels. Electrical: 2 × 7-pin and 1 × 15-pin front sockets, rear LED work light. Floor: Approx. 30 mm plywood floor on 8 longitudinal cross-members, forklift axle load up to 7,900 kg, premium sealed floor. Front Wall: 2,580 mm steel bulkhead with EN 12642 XL strength (0.8 × payload), Crash-Blocker and internal steel impact protection. Rear: Steel rear corner posts, EN 12642 XL rear portal (0.5 × payload), Fliegl I-Lock integrated door locking system (iF Design Award), lifetime warranty on frame-mounted locking components. Curtain: Reinforced curtain with welded horizontal and vertical straps, side curtain strength 0.4 × payload. Roof: Fliegl Blitz sliding roof with rear end lift, automotive L-roof beams, five-point roof fastening, additional roof safety hooks, non-elastic roof with minimal deflection, integrated rear rain gutter. Approval: Germany, EC type approval (2007/46), Fliegl EN 12642 XL, DL 9.5 and VDI 2700 Sheet 12 load securing certificates.

Condition: used, maximum load weight: 15,390 kg, overall weight: 18,000 kg, axle configuration: 2 axles, first registration: 06/2018, total width: 2,480 mm, Year of construction: 2018, Equipment: ABS, Fliegl ZWP 180 ZWP 2-axle platform trailer – AS NEW Gujdpfx Ao Ahqc Ushvei ! 4 units available! Fliegl platform trailer ZWP 180 ? First registration: 06/2018 ? Vehicle dimensions: 9,150 mm x 2,480 mm (L x W) ? Fully air-suspended ? Lifting/lowering system ? ABS ? 2 x air-suspended BPW axles – 9 tons ? Gross vehicle weight: 18,000 kg ? Unladen weight: 2,610 kg ? Payload: 15,390 kg ? Tire size front/rear: 385/65 R22.5 ? Tire tread depth: 8/8 / 7/7 mm - German vehicles! - First owner! - TÜV/inspection: on request and, if applicable, with an additional charge: new!! Errors and prior sale excepted!

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 8,700 kg, maximum load weight: 21,300 kg, overall weight: 30,000 kg, axle configuration: 3 axles, loading space length: 9,000 mm, loading space width: 2,520 mm, total length: 11,425 mm, total width: 2,550 mm, total height: 900 mm, tire size: 235/75 R17,5", tire condition: 100 %, color: original, Year of construction: 2026, Tailor-made transport solution Configure your Fliegl vehicle to your requirements. The vehicle shown is an example. Production and specification are customised to customer requirements. #Low Loader Drawbar Trailer Chassis Welded steel construction 1st pair of recessed wheel wells in track area 2nd pair of recessed wheel wells between axles in track area Removable wheel well covers with steel inserts Turntable with heavy-duty ball race, recessed storage box in front section Hydraulic rear support legs Aluminium storage box with stainless steel lid, W 600/H 400/D 500 mm Extendable outriggers to 3,000 mm at wheel well extensions Gedsznux Ispfx Ahvoui Central storage compartment for timber planks 70 mm timber planks for 3,000 mm extension Climbing strips on outer rear bevel frame #Lashing Points Low Loader 3 pairs of 10 t recessed lashing points in front floor 6 pairs of recessed 10 t mushroom lashing points in top and side outer frame Combined stake pockets with bolted ring lashing eyes, 5 t each, recessed in outer frame, approx. 72 x 42 mm internal size Additional recessed folding lashing rings in low loader deck, 10 t each #Drawbar Equipment Cranked drawbar #Axles + Suspension Drum brake axles, manufacturer's choice "Achsen-/Fahrwerk laservermessen" reduces tyre wear and fuel consumption #Braking System Twin-line air brake system Colour-coded pipe routing for easy servicing Spring parking brake Front Duomatic coupling with connection line to towing vehicle 24 V ABS and ALB with front ABS plug and connection cable #Wheels and Tyres 235/75 R 17.5 steel wheels, twin fitment, factory silver #Electrical System 12–24 V LED multi-chamber lights, side yellow LED lights, LED number plate light 2 front white LED position lights 2 rear white/red LED outline marker lights 1 x 15-pin front plug with connection cable 1 x 7-pin agricultural plug For use with 12/24 V LED lighting Additional rear LED work lights LED beacon with bracket 2 pairs of illuminated LED warning boards, extendable to 3,000 mm #Floor Front steel floor, followed by approx. 70 mm softwood floor Rear bevel with 70 mm softwood floor Low loader deck incl. rear bevel: 9,000 mm #Loading Ramps Climbing strips on ramp outer frame Timber-covered Hydraulic operation via PTO with flow control, left-hand side operation in direction of travel Individually controlled hydraulic side shift of loading ramps (only with hydraulic ramp operation) Hydraulic connection with SVK plug NW 10/3 incl. connecting hose #Registration / Plates Complete combination approval report for §70 permit application for one towing vehicle upon collection from Triptis (observe max. permitted gross combination weight in truck documents; apply for uprating in advance if required; approval is at the truck manufacturer's discretion. Any resulting costs will be charged separately) 24/7 service hotline Prepared for two-line number plate holder Reflective contour markings to ECE R 048, white sides, red rear

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 2,950 kg, maximum load weight: 15,050 kg, overall weight: 18,000 kg, axle configuration: 2 axles, total length: 9,470 mm, total width: 2,550 mm, total height: 1,080 mm, suspension: air, tire size: 445/45 R19,5", tire condition: 100 %, Customized Transport Solution Configure your Fliegl vehicle to meet your specific requirements. The vehicle shown is an example. Production and equipment are customized according to customer specifications. *Chassis with swivel turntable Fine-grained steel welded construction Fliegl “V-Stream” frame Front stop, longitudinally adjustable and foldable Pair of removable guide rollers, front and rear 4 container locks with sturdy arms based on 20" dimensions for 7.15 m and 7.45 m swap bodies (Note: When used in combination with the impact guard, the guard protrudes beyond the 7.15 m swap body) Note! Not suitable for 20" containers, or only possible if the container has a tunnel or opening at the front center measuring approx. 200 mm in length and 800 mm in width! Swivel mount with heavy-duty ball bearing swivel ring Wheel chocks with holders Aluminum side impact protection Side impact protection set inward for optimal clearance to the swap body supports Steel underrun protection Underrun protection shortened for optimal clearance to the swap body supports; lighting system mounted in a protected position Quarter-shell fenders in front and half-shell fenders in the rear Includes mud flaps for fenders Large Fliegl mud flap mounted transversely on the underrun protection at the rear *Trailer coupling system (turntable) Drawbar with certified 40 mm drawbar eye *Axles + Suspension SAF disc brake axles “Laser-measured axles/chassis” reduces tire wear and fuel consumption Air suspension *Brake System 2-line compressed air brake system Gsdpfszfp S Dsx Ahvsui Color-coded lines for easy maintenance. Air reservoir capacity: 208 liters Spring-loaded parking brake 2 non-reversible coupling heads at the front, with connecting lines to the tractor unit, 24-volt EBS, electronic braking system with EBS connector at the front, with connecting cable, Caution: The trailer may only be towed by tractor units that ensure the effectiveness of the ABS! with lift & lower valve + auto-reset function Axle load detection via EBS CAN bus signal, for display in the cab; the truck must be equipped accordingly “TPMS” tire pressure monitoring system according to ECE R 141, display in the towing vehicle via EBS *Wheels and tires 445/45 R19.5", brand selected by the manufacturer Steel rims, factory silver *Electrical system 24 volts, multi-chamber lights, yellow LED side lighting Yellow LED side lighting linked to the turn signals “Flashing side lights” 2 white front position lights 2 white/red rear lane-keeping lights 1 x 15-pin connector at the front, with connecting cable, additional LED work light(s) at the rear, activated via the reverse light LED work light at the front, centered between the cross members, shining toward the rear, activated via the reverse light *Country of registration/license plates Germany with DEKRA approval and certification (in accordance with §13 EG - FGV) 24/7 service hotline prepared for single-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white on the sides and red at the rear *Chassis galvanized or painted in colour of choice

Condition: used, maximum load weight: 6,580 kg, overall weight: 10,000 kg, axle configuration: 2 axles, first registration: 11/2020, next inspection (TÜV): 03/2027, loading space length: 6,200 mm, loading space width: 2,480 mm, loading space height: 2,400 mm, total width: 2,550 mm, total height: 3,700 mm, ° Central axle trailer Gusdpfx Ahoz Nbpgjvsi ° Chassis manufacturer: FLIEGL ° Curtain body with hoops ° Doors at front and rear (through-loader) ° 2 locks per door ° Sliding curtain on both sides ° Sliding roof ° 3-part aluminium slats ° Pallet stop rails ° Tyres: 235/75R17.5 143J ° Height-adjustable drawbar ° Reinforced cargo floor ° Lift/lower function ° Coupling heads red and yellow ° 24 Volt 15-pin lighting plug ° EBS connector ° Vehicle has normal signs of use

Condition: new, maximum load weight: 17,900 kg, overall weight: 24,000 kg, axle configuration: 3 axles, loading space length: 8,670 mm, loading space width: 2,500 mm, loading space height: 860 mm, total width: 2,520 mm, Total weight: 24,000 kg / 30,000 kg Unladen weight: 6,100 kg Payload: 17,900 kg / 23,900 kg Overall length: 10,890 mm Loading length: 8,670 mm total, 2,520 mm gooseneck, 6,500 mm loading platform Width: 2,520 mm Loading height: 860 mm Further information: Steel welded construction Turntable with robust ball bearing race Foldable rear support Chocks with holder Aluminum side impact protection Splash guards at the rear across the entire width (not in conjunction with forklift mount) Half-shell fenders on 1st axle with anti-splash flaps Anti-splash flaps behind the 2nd and 3rd axles Plastic toolbox Extendable widening sections to 3,000 mm Storage compartment for wooden planks in the center of the loading area Wooden planks 70 mm for widening to 3,000 mm Tie-down eyes, low-loader 1 pair of tie-down recesses embedded in the longitudinal beam at the front on the gooseneck, each 10 tons. 4 pairs of tie-down points in the outer frame of the gooseneck, each 5 tons (for attaching lashing straps) 7 pairs of tie-down mushroom heads embedded at the top and on the side in the outer frame, each 10 tons 1 x at the front on the gooseneck, 6 x in the low bed Pair of ring tie-down eyes embedded in the outer frame, each 5 tons (convertible to stake pockets) Additional pair of folding tie-down eyes, each 10 tons 1 x on the gooseneck 1 x behind the last axle embedded in the floor Coupling system, trailer turntable Drawbar with tested 40 mm drawbar eye Gsdpfx Aouytx Sjhvsui Drawbar height adjustment via spring Axles + Suspension Drum brake axles, at the manufacturer's choice "Axle/chassis laser-aligned" reduces tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearing and mechanical axle load compensation (rocker compensation) Wheels and Tires 235 / 75 R 17.5" at the manufacturer's choice Steel rims in twin arrangement, factory silver Braking System 2-line compressed air braking system Spring-loaded parking brake 2 failsafe coupling heads at the front, with connection lines to the towing vehicle 24 Volt ABS and ALB, with ABS plug at the front, with connection cable Electrical System 24 Volt, multi-chamber lights, yellow LED lighting on the side 2 white position lights at the front 2 white/red marker lights at the rear 2 x 7-pole failsafe plugs at the front, with connection cable LED rotating beacon with holder, switched via parking lights (beacon can be removed) Pair of warning signs, double LED illuminated and extendable to 3,000 mm Floor Gooseneck at the front with steel/diamond plate covering Storage box embedded in the ramp slope to the gooseneck followed by approx. 70 mm soft wood floor, in the wheel arch area steel/diamond plate covering Rear slope with 70 mm soft wood floor Low-loader platform including rear slope 6,500 mm Ramps Steel ramps 2,800 mm long, 750 mm wide, can be shifted laterally Additional ramp securing mechanism that folds down (to prevent ramps from sliding sideways, not in conjunction with lateral hydraulic ramp shifting) covered with wood (tip area with steel/diamond plate) Hydraulically operated via tractor's auxiliary drive with throttle, actuation on the right-hand side Hydraulic connection with SVK plug NW 10/3, including connection hose Painting Frame hot-dip galvanized including passivation Ramps hot-dip galvanized plus pre-transport / preparation from storage location 26639 Wiesmoor €1,280.00 / net

Condition: used, functionality: fully functional, machine/vehicle number: WFDFLT33902029406, empty load weight: 5,800 kg, maximum load weight: 29,200 kg, overall weight: 35,000 kg, axle configuration: 3 axles, first registration: 12/2021, next inspection (TÜV): 06/2027, loading space length: 13,650 mm, loading space width: 2,480 mm, loading space height: 2,790 mm, total length: 13,850 mm, total width: 2,550 mm, total height: 4,000 mm, suspension: air, tire size: 385/65 R22.5", color: silver, - Archive photographs; the vehicle may still be in use #Chassis - Semi-Trailer, General Haulage - Fine-grain steel welded construction in lightweight design - Fifth wheel plate with replaceable 2" kingpin - Coil well approx. 8,040 mm long - 6 coil supports (coil pockets, internal 82 x 52 mm) - Coil well cover with plywood panels and steel sub-beams - 2 split-strip coil well covers, each approx. 293 mm wide, weight approx. 13 kg per cover - Outer frame slightly angled with "Load-Lock-Profil" for lashing strap attachment - Note: bodyside boards must be opened to hook straps in when used together with bodyside boards - 9 pairs of lashing rings, 5 t each, recessed in the coil well area - 24 t two-speed landing gear, one-side operation, straight leg, without slide compensation - Note: clear corner dimension/rear swing radius of landing legs approx. 1,930 mm, legs retracted - Pull-out ladder at rear - Side door retainer - Aluminium side underrun protection, bracket fitted transverse to and on the chassis rail for supporting aluminium slats - Aluminium front underrun protection - Half-shell mudguards with anti-spray flaps to EC standard - Rear corner impact protection - 1 plastic toolbox - 2 pairs of stake pockets recessed in the outer frame, approx. 72 x 42 mm internal size - 2 stake pockets recessed centrally in the floor, approx. 72 x 42 mm internal size #Axles & Suspension - SAF disc brake axles with 430 mm disc diameter - Laser-aligned axles/running gear to reduce tyre wear and fuel consumption - Staggered axle spacing 1,410/1,310 mm (combined transport) up to 44 t gross train weight - Air suspension - Without lift axle #Braking System - 2-line air braking system, colour-coded pipework for easy servicing - Spring-actuated parking brake - 2 anti-mismatch coupling heads at the front, without connecting line - EBS made by Haldex - Electronic braking system with EBS socket at the front, without connecting cable #Wheels & Tyres - 385/65 R22.5" - Polished aluminium wheels - Wheel bolt protective caps #Electrics - 24 volt - Multi-chamber lights - Yellow LED side marker lights - Premium LED package including side marker lights with 20 LED diodes per light + LED safelight, at top of rear corner posts - 2 white LED front position lights - 2 white/red outline marker lights at rear - 1x 15-pin socket at front #Floor - Plywood panels approx. 30 mm thick, for high point-load capacity, forklift axle load up to max. 5,600 kg #Front Wall / Front Corner Posts - Steel corner posts, reinforced design - Release mechanism for side curtain at front wall - "Crash-Blocker" - Steel impact protection on lower inner section, approx. 140 mm high #Centre Posts - 3 pairs of sliding posts, movable along the entire length, with 4-way insert pockets and long pocket at the bottom Guodpfxewhp A Do Ahvei - 3 pairs of post positions #Rear Wall / Rear Corner Posts - Steel rear corner posts up to roof edge - Curtain attachment with round tube and curtain tensioning ratchet - Rear portal doors, 2-leaf, each with 2 internal rod locks - Fliegl "I-Lock" integrated door lock #Curtain - Curtain with welded-in horizontal and vertical straps - Tensioning buckles in stainless steel #Roof - Sliding roof, rear end-lift foldable - Roof sliding from rear to front - L-section roof rail for automotive industry use - Internal width between roof rails approx. 2,490 mm - "Roof non-elastic", minimal roof rail deflection during loading and unloading