Used Fliegl Zts Trailers for sale (346)

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 4,200 kg, maximum load weight: 16,800 kg, overall weight: 21,000 kg, axle configuration: 2 axles, loading space length: 5,000 mm, loading space width: 2,420 mm, loading space height: 600 mm, total length: 7,200 mm, total width: 2,550 mm, total height: 1,800 mm, suspension: air, tire size: 435/50 R19,5", tire condition: 100 %, Custom-made transport solution Configure your Fliegl vehicle according to your requirements. The vehicle shown is an example. Production and equipment are tailored to individual customer requirements. Chassis, central axle, tipping trailer Steel welded construction, continuous tipping shaft at the rear with 100 mm ball bearing Type 210, then total weight technically 21,000 kg (special permit required) Gearbox support leg at the front Retractable rear support 2 chocks with holder Under-ride guard, steel Splash guards at the rear over the entire width (not in conjunction with forklift holder) Quarter panel fenders in front of and behind each axle 1 plastic toolbox, w=600 / h=425 / d=460 mm, lockable 1 pair of aluminum ramps, 3,440 mm long, 360 mm wide, load capacity per pair 8,000 kg (attachment rail for ramps at the rear) Coupling device for central axle trailer Drawbar with tested 50 mm tow hitch Axles + suspension BPW disc brake axles "Axle/chassis laser-aligned" reduces tire wear and fuel consumption Axle spacing 1810 mm (then 10 tons axle load technically) Air suspension Braking system 2-line compressed air brake system Color-coded line routing for easy maintenance. Spring brake parking brake 2 fail-safe coupling heads at the front, with connecting lines to the tractor unit, 24 Volt EBS, electronic braking system with EBS connector at the front, with connection cable, Note: The trailer may only be towed by tractor units that guarantee the effectiveness of the ABS! with lift and lower valve Vehicle - driving stability system Axle load detection via EBS-CAN bus signal, for display on the display in the driver's cab, truck must be correspondingly pre-equipped, no truck installation (no calibrated scale) Wheels and tires 435/50 R19.5", manufacturer's choice Tires with 164 K or J marking, manufacturer's choice Steel rims, factory silver Electrical system 24 Volt, multi-chamber lights, yellow LED lighting on the sides 2 white position lights at the front in LED 2 white/red marker lights at the rear 2 x 7-pole fail-safe plugs at the front, with connection cable, 1 additional LED work light at the rear, switched via reversing light Hydraulics Three-way tipping mechanism, hydraulic multi-piston press with stroke limiter and safety cable, Low-pressure cylinder up to max. 170 bar, without throttle. If required, this can be retrofitted to the truck. (Truck with max. hydraulic delivery rate of 55 l/min) Operation hydraulically via truck PTO Hydraulic connection with SVK plug NW 10/3, incl. connection hose Tipping bridges Steel sheet floor Hardox 450, 4 mm thick, ball bearing at the rear, 100 mm diameter Side panel construction steel, side walls foldable and pivotally mounted with central locking at the bottom. Rear wall pivotable and as a 2-wing door (not foldable), with door holder and protective rubber on the side (not in conjunction with pivot or mesh grating attachment) Side wall retraction springs (not possible with foldable front wall) Platform width 2420 mm Todpfezd Eynjx Agmoc 5 pairs of lashing eyes in the floor, 5 tons each Painting Side panels/bridge painted in desired color Custom-made transport solution Configure your Fliegl vehicle according to your requirements. The vehicle shown is an example. Production and equipment are tailored to individual customer requirements.

Condition: new, functionality: fully functional, overall weight: 16,000 kg, maximum load weight: 13,700 kg, empty load weight: 2,300 kg, loading space width: 2,480 mm, loading space length: 7,750 mm, loading space height: 3,000 mm, machine/vehicle number: Produktpalette, Customized Transport Solution Configure your Fliegl vehicle to meet your specific requirements. The vehicle shown is an example. Production and equipment are customized according to customer specifications. Tedpfx Agskt Ni Uomoc Tandem Trailer Chassis Welded steel construction with a floor assembly approximately 152 mm high; load-bearing and torsionally rigid steel frame construction. Longitudinal beam floor construction with a load-resistant outer frame and guide tunnels spaced 600 mm apart; tunnels feature guides on top and sides, tunnel height approx. 45 mm; 4 x swap body corner fittings based on a 20-foot standard. 4 side-extending/folding parking feet with dual locking mechanism for a parking height of 970 mm, with support leg rest Side door stops Rear impact protection made of flat bar Pallet stops on both sides, approx. 20 mm high with perforated profile for securing straps; loading height is reduced by approx. 20 mm Floor Screen-printed panels approx. 27 mm thick, for high point load capacity, for forklift axle load up to max. 4,400 kg Front wall/corner stanchions Approx. 2,580 mm high, remainder covered with tarp; steel corner stanchions in full-size design; release mechanism for side tarp on front wall Inner front wall additionally lined with a 1,250 mm high screen-printed panel Center stanchions 1 pair of sliding stanchions adjustable along the entire length, with 4-compartment pockets and a long pocket at the bottom. 1 pair of stanchion positions Slotting Slats 5 rows of wooden V-shaped slotting slats Rear wall/rear corner stanchions Rear steel corner stanchions extending to the bottom edge of the roof, tarpaulin attachment with round tube and tarpaulin tensioning ratchet Rear portal doors, double-leaf, each with 2 internal twist-lock latches Tarpaulin Tarpaulin, with welded-in horizontal and vertical straps, reinforcements for stanchions Stainless steel tensioning fasteners Roof Sliding roof, rear end lift folds up, roof can be slid from rear to front, L-shaped roof rail for the automotive industry, interior width between roof rails approx. 2,490 mm, tarpaulin color: white EcoLift – lifting roof by approx. 380 mm, liftable on both sides, with gas spring assistance, Registration / Plates Country of registration: Germany Fliegl manufacturer’s certificate for body strength in accordance with EN 12642 XL, Fliegl manufacturer’s certificate for body strength in accordance with DL 9.5, pallet stops on both sides, approx. 20 mm high, loading height reduced by approx. 20 mm Fliegl manufacturer’s certificate for load securing in accordance with VDI 2700, Sheet 12 ff. Pallet stops on both sides, approx. 20 mm high; loading height is reduced by approx. 20 mm Paint Finish Frame Hot-dip galvanized, including passivation Front corner posts Hot-dip galvanized Front wall Aluminum Rear corner posts Hot-dip galvanized Rear wall White

Condition: new, maximum load weight: 8,780 kg, overall weight: 11,800 kg, axle configuration: 2 axles, loading space length: 5,000 mm, loading space width: 2,420 mm, loading space height: 950 mm, total width: 2,550 mm, Further information plus delivery/preparation from storage location 26639 Wiesmoor €1,280.00 / net Chassis Central Axle Tipping Trailer Steel welded construction, continuous tipping shaft at the rear with 80 mm ball bearing mount Front support leg with gearbox Foldable rear support 2 wheel chocks with holder Steel underrun protection Full-width rear mud flaps Quarter shell fenders 1 plastic toolbox, width=600 / height=425 / depth=460 mm, lockable Note! Sidewall touches the storage box when folded down. Lockable storage compartment for loading ramps underneath the loading area Central axle trailer drawbar arrangement Drawbar with certified 40 mm towing eye Drawbar height adjustable via spindle, adjustment range max. 300 mm Axles/Suspension GFA drum brake axles "Axle / Chassis laser measured" - reduces tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load equalization (rocker compensation) Wheels and Tires 235 / 75 R 17.5" manufacturer's choice Factory silver steel rims Braking System 2-line air brake system Color-coded line routing for easy servicing Manual spindle-operated parking brake ABS and ALB, with ABS plug at front and connection cable Attention: The trailer may only be towed by tow vehicles that ensure the operation of the ABS system! 2 foolproof coupling heads at the front, with connection lines to the truck Electrics 24 Volt, multi-chamber lights, yellow LED side lighting 2 white front position lights 2 white/red lane control lights at rear 2 x 7-pin foolproof plugs at front, with connection cable Hydraulics Three-way tipper, hydraulic multi-piston press with lift limit and safety cable Low-pressure cylinder up to max. 170 bar, without throttle. If necessary, retrofit on truck. Hydraulic connection with SVK plug NW 10/3, including connecting hose Operated hydraulically via truck PTO Tipper Body Sturdy tipper body with 4 mm steel floor, steel sidewalls, sides continuous, foldable and hung on pivots with central locking on bottom. Rear corner posts insertable. Rear wall foldable and hung on pivots, with central locking on bottom. Body length approx. 5,000 mm, sidewalls with 6 bottom hinges. Sidewall return springs (not available with split sidewalls) Body width 2,420 mm 5 pairs of lashing rings in floor, each rated to 5 tons Operating Notes The stated gross vehicle weight is technically possible, but depending on the type of load, the total weight may not be achieved when adhering to permitted axle / support / saddle loads. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of Registration / Plates Country of registration: Germany with Dekra inspection and certificate (according to §13 EC - FGV) Tedsy Dzk Eopfx Agmoc 24/7 service hotline Prepared for single-line license plate holder Outline marking with reflective strips according to ECE R 048, white on sides and red at rear Paintwork Frame hot-dip galvanized including passivation "15-year warranty against rust-through" Sidewall/body RAL 9005 deep black Optional: Drive-on ramps €1,280.00 / net

Condition: new, maximum load weight: 8,580 kg, overall weight: 11,800 kg, axle configuration: 2 axles, loading space length: 5,000 mm, loading space width: 2,420 mm, loading space height: 950 mm, total width: 2,550 mm, Further information plus pre-transport / provision ex warehouse location 26639 Wiesmoor €1,280.00 / net Chassis Central Axle Tipping Trailer Tsdjy Dzlispfx Agmsc Steel welded structure, continuous tipping shaft at the rear with 80 mm ball bearing Support leg with gear at the front Foldable rear support 2 wheel chocks with holders Steel underride guard Full-width rear mudflaps (not in combination with forklift mounting) Quarter-section mudguards 1 plastic toolbox, width=600 / height=425 / depth=460 mm, lockable (lock not included) Note! The sideboard touches the storage box when folded down. Lockable compartment for loading ramps under the cargo bed Drawbar system for central axle trailer Drawbar with certified 40 mm towing eye Drawbar height adjustable by spindle, max. adjustment range 300 mm Axles & Suspension GFA or BPW axles at manufacturer’s choice, with tapered roller bearings and S-cam brakes “Axle/chassis laser alignment” for reduced tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load equalization (rocker compensation) Wheels and Tires 235 / 75 R 17.5" as per manufacturer’s choice Steel rims in factory silver Braking System 2-line compressed air braking system Color-coded lines for easy servicing Hand spindle parking brake 24 Volt ABS and ALB, ABS connector at the front, with connection cable Note: The trailer may only be towed by vehicles that ensure ABS functionality! 2 mistake-proof coupling heads at the front, with connection lines to the truck Electrics 12 to 24 Volts, multi-chamber LED lights, side yellow LED marker lights, license plate lighting in LED (Note! Certain towing vehicles may display diagnostic errors even if functionality is correct) 2 white position lights at the front 2 white/red lane marking lights at the rear 2 x 7-pin mistake-proof plugs at the front, with connection cable 1 additional LED work lamp at rear, activated by reverse light Hydraulics Three-way tipping system, hydraulic multi-piston press with lift limit and safety cable Low-pressure cylinder up to max. 170 bar, without restrictor. If required, this must be retrofitted to the truck (trucks with max. hydraulic pumping capacity of 55 l/min) Hydraulic connection with SVK plug NW 10/3, including connecting hose Operated hydraulically via truck PTO Tipper Platform Robust tipper platform with 4 mm steel floor, steel sides, continuous and foldable and swinging sideboards with central locking at the bottom. Removable corner posts at the rear. Drop-down and swinging tailgate, with central locking at the bottom. Platform length approx. 5,000 mm, sidewalls with 6 hinges at the bottom. Sideboard retracting springs (not available with foldable front wall) Platform width 2,420 mm 3 pairs of lashing eyes on floor, each rated for 5 t Operating Instructions The specified gross weight is technically possible. Depending on cargo, the gross weight may not be achievable while adhering to permitted axle, support, and kingpin loads. (Poor driving and trailing behavior can result from improper load distribution) Country of Registration / Plates Registered in: Germany With Dekra inspection and certificate (according to §13 EG-FGV) 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips according to ECE R 048, white on sides and red at the rear Paintwork Frame hot-dip galvanized incl. passivation "15 years warranty against corrosion through rust" Sideboard/Platform in RAL

Condition: used, functionality: fully functional, machine/vehicle number: WFDFLT33902037031, empty load weight: 4,795 kg, maximum load weight: 30,320 kg, overall weight: 35,000 kg, axle configuration: 3 axles, first registration: 09/2025, loading space length: 7,200 mm, loading space width: 2,470 mm, loading space height: 1,450 mm, loading space volume: 25 m³, total length: 8,600 mm, total width: 2,550 mm, total height: 3,040 mm, suspension: air, tire size: 385/65 R22.5", tire condition: 100 %, color: grey, These images are archive images! The vehicle may still be in use! Fine-grain steel welded construction, in basic lightweight design, kingpin plate with replaceable 2" kingpin, Curved front end "Patented" 24-ton, 2-speed landing gear, single-sided operation, with semi-circular lower part and straight connection plate, with stroke compensation Support wedges with holder Underrun protection, foldable Tjdpfx Ajy Rrplogmsc Half-shell fenders Integrated "fender holder," surface resistant to stone chipping with anti-splash flaps only on the last axle Tarpaulin rod with holder Towing hook at the rear (not on Revolution model) Axles + Suspension SAF disc brake axles with 430 mm disc diameter "Axle/chassis laser-aligned" – reduces tire wear and fuel consumption Axles in off-road design Air suspension 1st axle: automatic lift axle, including forced lowering and starting assistance, activated by "3x braking" (starting assistance is functional up to an axle load exceeding 30% and up to a speed of max. 25 km/h) "Hot-dip galvanized lift axle mechanism" Braking system 2-line compressed air braking system Color-coded line routing for easy maintenance Spring-loaded parking brake 2 fail-safe coupling heads at the front, without connecting line 24-volt EBS, electronic braking system with EBS socket at the front, without connecting cable Note: The trailer may only be towed by tractor units that ensure the effectiveness of the ABS! with lifting and lowering valve Vehicle - driving stability system Automatic tilting lowering with shut-off valve "TPMS" tire pressure monitoring system - display on the tractor unit, via EBS, without truck installation (the truck must have the necessary prerequisites. Only on base tires). Wheels and tires 385/65 R22.5" Steel rims Electrical system 24 volts, multi-chamber lights in LED, yellow LED lighting on the sides, license plate lighting in LED (Note! with certain tractor units, false diagnoses may occur, although the function is given) Yellow LED lighting on the sides linked to the turn signal "flashing side lights" 2 white position lights at the front in LED 2 white/red outline lights at the rear in LED 2 x 7-pole and 1 x 15-pole fail-safe sockets at the front, without connecting cable Additional LED work light, integrated and recessed at the rear, switched via reversing light Hydraulics Low-pressure cylinder max. 170 bar Operation hydraulically via truck auxiliary drive Bins Aluminum box body made of high-quality, abrasion-resistant material. Sloping front wall, 5 mm thick, with external cylinder mount. Side walls made of 30 mm hollow chamber profiles, cleanly welded, with top rail profile that prevents spillage. Inside with access ladder on the front wall (not in conjunction with Cramaro). Shovel and broom holder outside on the front wall. Greenline - conical and aerodynamic bin shape "Membrane" - rear wall Rear wall as a hinged flap with "double-hinge hinge," externally mounted with double hook lock. Rear wall with rubber seal Floor continuous, 6 mm thick Standing platform with access ladder, connecting plate for air/electrical and brake connections with large clearance for optimal operability. Roll tarp, can be folded to the right side, with central locking on the left side Operating instructions For transport of salt, lime, etc., we recommend a tipping cylinder with a hard-chrome plated piston rod, so that it is not attacked and rusted by the material.

Condition: new, maximum load weight: 16,920 kg, overall weight: 24,000 kg, axle configuration: 3 axles, loading space length: 8,200 mm, loading space width: 2,520 mm, loading space height: 900 mm, total width: 2,550 mm, Total weight: 24,000 kg / 30,000 kg Unladen weight: 7,080 kg Payload: 16,920 kg / 22,920 kg Overall length: 10,825 mm Loading length: 8,200 mm total Tsdjzhhw Dopfx Agmsc Width: 2,5250 mm Loading height: 900 mm Additional information: plus pre-transport / preparation from warehouse location 26639 Wiesmoor: €1,280.00 net Chassis, low loader trailer Steel welded construction Turntable with robust ball bearing, storage box embedded in the turntable extension Rear support, foldable 2 jacking pads with holder Aluminum side impact protection Mud flaps at the rear, covering the entire width (not in conjunction with forklift holder) Quarter fenders in front of and behind the 1st axle, with anti-spray mud flaps behind the 2nd and 3rd axles 1 spare wheel holder for 1 spare wheel, with wheel fastening set 1 plastic toolbox, w=600 / h=425 / d=460 mm, lockable Extensions, extendable to 3,000 mm (not in rear slope) (however, the track width of the construction machines or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Storage compartment for wooden planks in the center of the loading area Wooden planks, 70 mm, for extension to 3000 mm Tie-down points, low loader 3 pairs of tie-down points, each 10 tons, integrated into the floor at the front 6 pairs of tie-down loops, each 10 tons, recessed at the top and sides in the outer frame 1 x in the neck area remainder distributed in between 1 x rear slope 5 pairs of ring tie-down points recessed in the outer frame, each 5 tons (convertible to stake pockets) 1 pair of folding tie-down points additionally recessed into the low loader floor behind the 3rd axle, each 10 tons 1 pair of screw tie-down points at the front in the corners, each 6.7 tons, with a large flange plate including thread as a counter holder Coupling device, trailer, turntable Drawbar with tested 40 mm drawbar eye Axles + Suspension Drum brake axles, at the manufacturer's choice "Axle/chassis laser-aligned" – reduces tire wear and fuel consumption Air suspension with raising & lowering valve Braking system 2-line compressed air braking system Color-coded line routing for easy maintenance Spring-loaded parking brake 2 fail-safe coupling heads at the front, with connection lines to the tractor unit 24 Volt EBS, Electronic Braking System with EBS plug at the front, with connection cable Attention: The trailer may only be towed by tractor units that guarantee the effectiveness of the ABS! Axle load recognition via EBS-CAN bus signal, for display on the display in the driver's cab, the truck must be appropriately prepared, no truck installation (no calibrated scale) Vehicle - Driving Stability System "TPMS" Tire Pressure Monitoring System according to ECE R 141, display on the display in the tractor unit, via EBS, without truck installation (this must be a prerequisite in the truck. Only on standard tires) Wheels and tires 235 / 75 R 17.5" Tires at the manufacturer's choice Steel rims in twin arrangement, factory silver Electrical system 24 Volt, multi-chamber lights, yellow LED lighting on the sides yellow LED lighting on the sides, linked to the turn signal "flashing side lights" 2 white position lights at the front 2 white/red side marker lights at the rear 2 x 7-pole fail-safe plugs at the front, with connection cable, 1 LED rotating beacon with holder, switched via parking lights (beacon removable) 2 pairs of warning boards, double LED illuminated and extendable to 3,000 mm Floor Front area, steel floor thereafter with approx. 70 mm

Condition: used, functionality: fully functional, machine/vehicle number: WFDFLT23002022053, empty load weight: 5,760 kg, maximum load weight: 23,240 kg, overall weight: 29,000 kg, axle configuration: 2 axles, first registration: 10/2017, loading space length: 14,900 mm, loading space width: 2,480 mm, loading space height: 2,790 mm, total length: 15,150 mm, total width: 2,550 mm, total height: 4,000 mm, suspension: air, tire size: 385/65 R22,5", tire condition: 70 %, color: black, Please note: the pictures are archive images. The vehicle may currently be in use. # Chassis – semi-trailer for general haulage - Fine-grain steel welded construction - Upper coupler plate with replaceable 2" kingpin - Outer frame slightly inclined, with "Load-Lock" profile for attaching lashing straps - 24 t 2-speed landing gear, one-side operation, semi-round feet and straight mounting plate, with movable thrust compensation - Folding rear support - Pull-out ladder at rear - Door retainers on sides - Wheel chocks with holders - Aluminium side underrun protection - Galvanised steel rear underrun protection - Quarter mudguards in front of and behind axle assembly - Rear corner impact protection - Ferry lashing eyes - Pallet stops on both sides, approx. 15-20 mm high, bolted; loading height reduced by approx. 15-20 mm - Plastic toolbox with drawer and shelf, W=650 / H=520 / D=670 mm # Axles + suspension - SAF disc brake axles, 430 mm disc diameter - Axles/running gear laser-aligned: reduced tyre wear and fuel consumption - Air suspension - No lift axle # Braking system - Dual-line compressed air braking system - Spring brake parking brake - 2 polarity-protected coupling heads at front, without connecting hoses - EBS (electronic braking system) with EBS socket at front, without connecting cable - Raise/lower valve - Roll stability system - Axle load detection via EBS CAN bus signal for display in driver's cab; tractor unit must be prepared accordingly, no installation on the tractor unit (not a calibrated scale) # Wheels and tyres - 385/65 R22.5, brand at manufacturer's discretion - Steel rims, factory silver # Electrics - 24 V - LED multi-chamber lamps with resistor - Yellow LED side marker lights - LED number plate lighting - 2 white LED front position lights - 2 white/red LED rear outline marker lights - 2 x 7-pin and 1 x 15-pin polarity-protected sockets at front, without connecting cables - Additional LED work light at rear, switched via reversing light - Reversing camera system with colour flat-screen monitor, wireless connection to screen, suction-cup mount, power supply via 24 V vehicle socket # Floor - Phenolic-coated plywood approx. 30 mm, transverse joints with omega inserts - On longitudinal bearers for high point loads, forklift axle load up to max. 7100 kg # Headboard/front corner posts - Height 2 580 mm - Reinforced steel corner posts - Side curtain release device at headboard Tjdpfx Aoz Egqzogmjc - "Crash-Blocker", inside at bottom at approx. 140 mm height with steel impact protection # Rear frame/rear corner posts - Rear steel corner posts up to roof underside - Curtain attachment with round tube and curtain tensioning ratchet - Rear portal doors, 2-leaf, each with 2 internal locking bars # Curtain - Curtain with welded-in horizontal and vertical straps - Stainless steel tensioning buckles - Customer lettering on side curtains and rear portal # Roof - Sliding roof, slides from rear to front; rear roof lift folds upwards - L-shaped roof rail for automotive industry, internal width between roof rails approx. 2 490 mm - EcoLift lifting roof, raisable by approx. 380 mm on both sides, gas strut assisted - Optimised rain gutter at rear, on top of rear roof bow above doors Please note: archive images!

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 3,100 kg, maximum load weight: 34,900 kg, overall weight: 38,000 kg, axle configuration: 3 axles, total length: 7,690 mm, total width: 2,550 mm, suspension: air, tire size: 385/65 R22,5", tire condition: 100 %, Custom-Made Transport Solution Configure your Fliegl vehicle according to your requirements. The vehicle shown is an example. Production and equipment are tailored to individual customer needs. Chassis, Saddle, Container Fine-grained steel welded construction, saddle plate with 2 replaceable kingpins Container receptacles: 1 x 20 ft in the center (or swap body container 7.15 / 7.45), not retractable at the front, the pivot pins of the container locking mechanism in the longer version 24 tons, two-stage support jacks, single-sided operation With anti-splash flaps according to EC standards Front axle drip tray with 1 1/4 inch drain pipe + 1 1/4 inch shut-off valve, including drip pan, with perforated tread plates, approx. 400 mm wide, left + right between the drip tray and the longitudinal beam 4 hose racks, approx. 4500 mm long (hose box) for hose pipes, 2 x DN 200 on the outside + 2 x DN 160 arranged in the center, at the rear hose box (stainless steel) 300 mm deep, splash-proof, lid (stainless steel) all around with rubber seal, with drain hole at the lowest point, then without lid on the hose pipes 1 stainless steel grounding lug at the rear on the right side of the frame, with international grounding sticker on the frame Climbing steps at the rear right on the underrun protection, at the rear right on the outside of the main beam, tread plate approx. 260 mm long and 300 mm wide Axles + Suspension SAF disc brake axles Tjdpfx Aei Rixkjgmoc Axle/suspension laser-measured for reduced tire wear and fuel consumption Offset axle spacing (combined transport) up to 44 tons total train weight Air suspension 1st axle: automatic lift axle, including forced lowering and start-up assistance, activation 3x brake Braking system 2-line compressed air braking system Color-coded line routing for easy maintenance Spring brake parking brake 2 fail-safe coupling heads at the front, without connecting line EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by tractor units that ensure the effectiveness of the ABS! With raising and lowering valve Vehicle - Driving stability system Axle load detection via EBS-CAN bus signal, for display via the display in the driver's cab, truck must be prepared accordingly, no truck installation (no calibrated scale) Wheels and tires 385/65 R22.5, manufacturer's choice Steel rims, factory silver Electrical system 24 volts, multi-chamber lights, yellow LED lighting on the sides 2 white position lights at the front 2 white/red side marker lights at the rear 1 x 15-pole socket at the front, without connecting cable Operating instructions The specified total weight is technically possible, but depending on the load, the total weight may not be reached while complying with the permissible axle/support and saddle loads. (Poor driving and handling behavior may occur due to incorrect load distribution) This vehicle may only be loaded with 20' tank containers that comply with ISO 668 and in particular ISO 1496-3! The tank containers must have "end-load-transfer areas"! Country of registration / signs Germany Type approval according to EC 2007/46 24/7 service hotline Prepared for single-row license plate holder Warning sign according to ECE - 70 Acceptance according to ADR, according to 9.1.1.2 of the ADR, EX/II, EX/III / Vehicle registration certificate for the transport of certain dangerous goods (ex.B3) with warning sign on the rear, not valid for substances according to UN 0

Condition: used, functionality: fully functional, machine/vehicle number: WFDFLT21801011727, empty load weight: 3,200 kg, maximum load weight: 14,800 kg, overall weight: 18,000 kg, axle configuration: 3 axles, first registration: 01/2022, total length: 10,020 mm, total width: 2,550 mm, total height: 1,070 mm, suspension: air, tire size: 445/45 R19,5", color: silver, Tandem swap body trailer type TWP 180 Mega-EL Caution: images are stock/archive photos. The vehicle may be in use. #Weights and dimensions - Gross vehicle weight: 18000 kg - Payload approx.: 14800 kg - Kingpin/support load: 1000 kg - Unladen weight (base version) only approx.: 3200 kg +/- production tolerance - Overall length with 7820 mm swap body approx.: 10020 mm - Overall width max.: 2550 mm - Frame height lowered approx.: 1010 mm - Frame height raised approx.: 1390 mm - Frame height in driving position approx.: 1070 mm - Parking height approx.: 1040 to 1320 mm - Standard stop to front locking unit approx.: 985 mm - Locking unit spacing: 5853 mm - Coupling eye height approx.: 380 mm - Drawbar length set from stop, 7820 mm swap body, approx.: 2200 mm - Parking heights apply on level ground #Chassis - swap body centre-axle trailer - Fine-grain steel welded construction - Front stop, longitudinally adjustable and foldable - 2 pairs of removable guide rollers, front and rear - 4 twistlocks with reinforced brackets on 20" base for swap bodies 7.15 / 7.45 and 7.82 - 1 pair geared landing legs front, straight foot, one-side operation on RHS - 1 pair geared landing legs rear, straight foot, one-side operation on RHS - 2 wheel chocks with holder - Aluminium side underrun protection - Steel rear underrun protection - Half-shell mudguards - Mudflaps #Coupling assembly - centre-axle trailer - Drawbar with certified 50 mm coupling eye, haulage version (not suitable for trucks with tail lift) - Underslung drawbar coupling, free drawbar length approx. 2200 mm - Brake/electrical connection plate on drawbar, all lines to towing vehicle as coiled cables #Axles and suspension - SAF disc brake axles - Laser-aligned axles/chassis, reducing tyre wear and fuel consumption - Air suspension #Braking system - 2-line air braking system - Colour-coded line routing for easy servicing Tsdpfx Aezwlciogmec - Air reservoir capacity 208 litres - Spring-loaded parking brake - 2 mismatch-proof coupling heads front, with lines to towing vehicle, RHS connection - EBS electronic braking system with EBS connector front, with cable, RHS connection - Caution: only to be towed by vehicles with effective ABS - Raise-and-lower valve with hold function in lowered/raised position #Wheels and tyres - 445/45 R19.5" make of manufacturer's choice - Steel rims, factory silver #Electrics - 24V multi-chamber lights, yellow LED side marker lights - 2 white front position lights - 2 white/red rear outline marker lights - 2 x 7-pin mismatch-proof connectors front, with cable, RHS connection - 2 additional LED work lights, flush-mounted at rear, activated via reverse light #Country of registration / plates - Germany - Dekra inspection and certificate per §13 EC-FGV - 24/7 service hotline - prepared for single-line number plate holder - Contour marking with reflective tape to ECE R048, white sides, red rear #Paintwork - Frame hot-dip galvanised incl. passivation, 15-year warranty against corrosion perforation Caution: stock photos!

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 5,600 kg, maximum load weight: 24,400 kg, overall weight: 30,000 kg, axle configuration: 3 axles, loading space length: 5,900 mm, loading space width: 2,520 mm, loading space height: 860 mm, total length: 10,290 mm, total width: 2,550 mm, total height: 860 mm, suspension: steel, tire size: 235/75 R17,5", tire condition: 100 %, color: original, Year of construction: 2026, Tailor-made transport solution Configure your Fliegl vehicle to your requirements. The vehicle shown is an example. Production and specification are customised to customer requirements. #Low Loader Drawbar Trailer Chassis Welded steel construction Turntable with heavy-duty ball race Folding rear support legs 2 wheel chocks with holders Half-shell mudguards on 1st axle Quarter mudguards behind 2nd and 3rd axles Side underrun protection Yellow side LED lights instead of reflectors Full-width rear mudflap (not in combination with forklift mounting) 1 lockable plastic toolbox, W 600/H 425/D 460 mm #Lashing Points Low Loader 1 pair of recessed 10 t lashing cut-outs in front gooseneck side members 7 pairs of recessed 10 t lashing points in top and side outer frame 1 on front gooseneck 5 in low bed 1 in rear bevel 12 pairs of 5 t lashing holes in outer frame (for load straps) 5 on gooseneck, 6 in low bed and 1 in rear bevel #Drawbar Equipment Drawbar with certified 40 mm towing eye Spring-assisted drawbar height adjustment #Axles + Suspension Drum brake axles, manufacturer's choice "Achsen-/Fahrwerk laservermessen" reduces tyre wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bushes and mechanical axle load equaliser #Wheels and Tyres 235/75 R17.5 Manufacturer's choice Twin steel wheels, factory silver #Braking System Twin-line air brake system Spring parking brake 2 non-interchangeable front coupling heads with connecting lines to towing vehicle Connecting lines extended by approx. 60 cm Without ABS, with mechanical ALB, max. 60 km/h approval #Electrical System 12 V multi-chamber lights with yellow side LED lights Flashing side LED lights linked to indicators 2 front white position lights 2 rear white/red outline marker lights 1 x 7-pin 12 V front plug with connecting cable, extended by approx. 60 cm 1 removable LED beacon with bracket, switched via side lights 2 pairs of illuminated warning boards, extendable to 3,000 mm #Floor Front gooseneck with steel chequer plate Recessed storage box in transition to gooseneck Approx. 70 mm softwood floor, steel chequer plate in wheel arch area Rear bevel with 70 mm softwood floor Low loader deck incl. rear bevel: 5,900 mm #Loading Ramps Steel ramps, 3,000 mm long, 750 mm wide, laterally adjustable Timber-covered (steel chequer plate at ramp tips) Hydraulic operation via PTO with flow control, left-hand side operation in direction of travel Hydraulic connection with SVK plug NW 10/3 incl. connecting hose #Paint Finish Chassis painted DB 7350 Nova Grey "10 Jahre Gewährleistung gegen Durchrostung" Drawbar galvanised or black, manufacturer's choice Loading ramps hot-dip galvanised Tedpfxeznw U Ej Agmsc

Condition: used, functionality: fully functional, machine/vehicle number: WFDFLT33902031174, empty load weight: 5,835 kg, maximum load weight: 29,165 kg, overall weight: 35,000 kg, axle configuration: 3 axles, first registration: 06/2023, loading space volume: 50 m³, total length: 10,300 mm, total width: 2,550 mm, total height: 3,740 mm, suspension: air, tire size: 385/65 R22,5", color: grey, The images shown are archive photos. The vehicle may still be in use. Chassis Tipping Semi-Trailer Fine-grained steel welded construction in Basic lightweight design, fifth wheel plate with replaceable 2" king pin Curved front wall (patented) 24 t 2-speed support legs, single-sided operation, with straight base, without compensating rod 2x wheel chocks with holder Aluminium side underrun protection Rear under-run protection, foldable 6x half-shell mudguards Integrated mudguard holders with stone-repellent surface Tarpaulin rod with bracket 2x rear towing hooks Axles & Suspension BPW disc brake axles "Axle/chassis laser alignment" reduces tyre wear and fuel consumption Air suspension 1st axle with automatic lift, including forced lowering and starting aid, operated by '3x brake' application Braking System 2-line compressed air braking system Colour-coded routing for easy servicing Spring-type parking brake 2 non-interchangeable coupling heads at the front, without connection line EBS (Electronic Braking System) with EBS socket at the front, without connection cable Note: This trailer must only be towed by tractor vehicles that ensure ABS functionality! With lift & lower valve Vehicle stability control system Wheels and Tyres 6x 385/65 R22.5" tyres 6x steel rims Electrics 24 Volt, multi-chamber lights, side yellow LED lighting 2 white marker lights at front 2 white/red lane marker lights at rear 2 x 7-pin and 1 x 15-pin non-interchangeable sockets at front, without connection cable Hydraulics Low-pressure cylinder max. 170 bar, smallest stage hard chrome plated, with HDK screw coupling, fixed part, NW 48 mm (without hose connection) Tipping Body Aluminium box body made of high-quality, abrasion-resistant material Sloped 5 mm thick front wall with external cylinder mounting Side walls made of 30 mm hollow chamber profiles, clean welded, with bulk material deflecting top rail. Internal ladder at the front wall Shovel and broom holders outside front wall Rear wall with pendulum mounting and 'double-joint' hinges, with 2-winged door split 1/2 to 1/2, upper swing beam, with one grain slide per door Rear wall with rubber seal 6 mm continuous floor Standing platform with access, connecting plate for air/electric/brake Roll tarp can be stowed one side (FR-right), with central locking (FR-left) Operating Notes For transporting salt, lime, etc., we recommend a tipping cylinder with a hard chrome-plated piston rod to prevent corrosion and damage from the material. The total weight stated is technically possible; depending on the cargo, the full weight may not be achievable within the permissible axle/support/saddle loads (incorrect load distribution may result in poor handling and tracking). Note! Not suitable for chemically aggressive substances (e.g., acids, chlorine compounds, sulphur compounds, alternative fuels); such substances can cause stress corrosion cracking and extreme cracking in the body when combined with moisture on the body surface! Vehicles with load bodies are intended for chemically non-aggressive cargo. Use for transporting aggressive goods such as acids, bases, salts, fertilizers, sewage sludge, and household waste is at the operator's own risk. This can result in damage such as stress corrosion cracking or pitting. Todpey Efcusfx Agmsc Archive images are shown!

Condition: new, maximum load weight: 17,900 kg, overall weight: 24,000 kg, axle configuration: 3 axles, loading space length: 8,670 mm, loading space width: 2,500 mm, loading space height: 860 mm, total width: 2,520 mm, New vehicle Fliegl 3 axle low loader trailer with ramps, type DTS 300 Vehicle completely hot-dip galvanized Total weight: 24,000kg/30,000kg Empty weight: 6,100kg Payload: 17,900/23,900kg Total length: 10,890mm Loading length: 8,670mm total, 6,500mm low bed including rear bevel / 2,170mm offset Width: 2,520mm Loading height: 860mm Further information plus pre-freight / provision from storage location 26639 Wiesmoor 1,280.00 ¤/ net Rent-purchase offer: term 48 months, down payment only VAT, residual value 40% monthly rate: EUR 569.00 Steel Welded construction Pivot bolster with strong ball bearing ring Foldable rear support Wheel chocks with holder Aluminum side impact protection Splash flaps at the rear over the entire width (not in conjunction with forklift bracket) Half-shell mudguard on 1st axle with anti-spray splash flaps Anti-spray splash flaps behind 2nd and 3rd axles 1 plastic tool box, w=600 / h=425 / d=460 mm, lockable Extensions extendable to 3,000 mm (not in the rear bevel) (The track width of the construction machines or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Storage compartment for wooden planks in the middle of the loading area 70 mm wooden planks for widening to 3,000 mm Lashing eyes for low loader 1 pair of lashing cutouts in the longitudinal beam at the front on a bend, 10 tonnes each. 4 pairs of lashing holes in the outer frame of the crank, each with 5 tons (tension belt attachment) 7 pairs of lashing mushrooms, set into the outer frame at the top and side, each with 10 tons 1 x at the front on the crank 6 x in the low bed First lashing eye 250 mm from the front and last max. 250 mm from the back, distance between the lashing eyes not greater than 1100 mm 5 pairs of ring lashing eyes set into the outer frame, each with 5 tons (can be converted to stake pockets) 2 additional pairs of folding lashing eyes, each with 10 tons 1 x on the crank (protrudes) 1 x set into the ground behind the last axle Towbar with tested 40 mm towbar Towbar height adjustment via spring Axles + suspension Drum brake axles, as selected by the manufacturer "Laser-measured axle/chassis" Reduction in tire wear and tear Fuel consumption Air suspension with raising and lowering valve Tjdpjv D T R Eefx Agmoc Wheels and tires 235 / 75 R 17.5" at the manufacturer's discretion Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-loaded parking brake Vehicle driving stability system Axle load detection via EBS-Canbus signal, for display on display in the driver's cab, truck must be prepared accordingly, no truck installed (no calibrated scales) 2 interchangeable coupling heads at the front, with connecting cables to the motor vehicle, 24 volt EBS, electronic braking system with EBS plug at the front, with connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrics 24 volts, multi-chamber lights, yellow LED lighting on the side 2 white position lights at the front 2 white/red lane keeping lights at the rear 2 x 7-pin, interchangeable plugs at the front, with connecting cable, 1 LED rotating beacon with holder, switched via parking light (light removable) 2 pairs of warning signs with double LED lighting and extendable to 3,000 mm Floor Front bend with steel/checker plate covering Storage box embedded in the crossing slope to the bend then with approx. 70 mm softwood floor, steel/checker plate covering in the wheel arch area Rear bev

Condition: used, machine/vehicle number: WFDFLT33802021791, empty load weight: 6,433 kg, maximum load weight: 28,567 kg, overall weight: 35,000 kg, axle configuration: 3 axles, first registration: 11/2017, loading space length: 13,650 mm, loading space width: 2,480 mm, loading space height: 3,000 mm, total length: 13,850 mm, total width: 2,550 mm, total height: 4,000 mm, suspension: air, tire size: 445/45 R19,5", color: black, Please note: The images shown are archive photos. The vehicle may still be in operation. ## Fliegl Mega Curtainsider Semi-Trailer Chassis: Lightweight fine-grain steel chassis, replaceable 2" kingpin, Load-Lock outer frame, 24 t JOST two-speed landing gear, rear access ladder, door retainers, aluminium side underrun protection, galvanised rear underrun protection, quarter mudguards, anti-spray mud flaps, Heavy Blocker rear impact protection with side roller buffers, heavy-duty pallet stop, spare wheel carrier, lockable toolbox with drawer, document box. Axles & Suspension: BPW drum brake axles (8-stud hubs), laser wheel alignment, mechanical hubodometer, air suspension, automatic lift axle with forced lowering and traction aid (activated by brake pedal or manual switch). Brakes: Dual-line air brake system, spring parking brake, WABCO EBS, lift/lowering valve. Raising the lift axle increases loading/overall height by approx. 50 mm. Tyres: 445/45 R19.5 (manufacturer's choice). Electrical: 24 V LED lighting, LED side markers, LED front position lights, LED rear outline lights, 2 × 7-pin and 1 × 15-pin front sockets. Floor: Approx. 30 mm plywood floor with Omega-reinforced joints, suitable for forklift axle loads up to 7,100 kg. Front Wall: 2,580 mm high, steel corner posts, curtain release system, internal steel impact protection, additional 1,250 mm plywood lining. Centre Posts: 3 pairs of full-length sliding posts with multiple locking positions. Side Slats: Aluminium or timber V-slats. Rear: Steel rear corner posts, double rear doors with internal locking bars, curtain tensioning system. Curtains: Reinforced curtains with welded horizontal and vertical straps, stainless steel buckles. Tedpfozlciiox Agmec Roof: Sliding roof, rear end lift, automotive L-roof rails, hydraulic lifting roof on both sides (+400 mm), rain gutter at rear. Certification: DEKRA approval, EN 12642 XL load securing certificate, VDI 2700 Sheet 12 beverage transport certification, ECE R70 rear warning plate.

Condition: new, maximum load weight: 8,840 kg, overall weight: 11,800 kg, axle configuration: 2 axles, loading space length: 6,200 mm, loading space width: 2,480 mm, loading space height: 900 mm, total width: 2,550 mm, Total length: 8,000 mm Loading length: 6,200 mm including rear chamfer Further information plus freight / provision from stock location 26639 Wiesmoor €1,280.00 net Loading width: 2,480 mm Chassis: central axle trailer Fine-grain steel welded construction Outer frame, slightly angled, new version with “Load-Lock profile” for lashing strap attachment Pair of lashing rings on the outside base, each 5 t 1 x in the front corners, 1 x in front of and 1 x in the rear chamfer at the back 6 pairs of lashing rings on the outer floor/frame, each 5 t Tjdoyl E Dqjpfx Agmjc Gear support leg at the front Rear support, foldable Wheel chocks with holder Aluminum side underrun protection Galvanized steel rear underrun guard Full-width rear spray flaps (not in conjunction with forklift mount) Quarter-circle mudguards 1 plastic toolbox, w=600 / h=425 / d=460 mm, lockable Towing device for central axle trailer Drawbar with tested 40 mm towing eye Drawbar height-adjustable via spindle, max. adjustment range 300 mm Axles & suspension GFA or BPW axles according to manufacturer’s choice, with tapered roller bearings and S-cam brakes "Axle/chassis laser alignment" reduces tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber mounting and mechanical axle load equalizing (rocker equalizer) Braking system 2-line compressed-air braking system Color-coded piping for easy service Hand-spindle parking brake 2 non-interchangeable coupling heads at the front, with connection lines to the towing vehicle 24 volt ABS and ALB, with ABS plug at the front, with connection cable Attention: The trailer may only be towed by towing vehicles that guarantee proper functioning of the ABS! Wheels and Tires 235/75 R17.5, make as per manufacturer’s choice Steel rims, factory silver Electrics 24 volt, multi-chamber lamps, side yellow LED lighting 2 white position lamps at the front (LED) 2 white/red marker lamps at the rear 2 x 7-pin non-interchangeable plugs at the front, with connection cable Floor Steel/chequer plate floor for high point load capacity Note: Slight floor waviness due to welding distortion possible! Platform length approx. 6,200 mm Rear chamfer approx. 900 mm Front bulkhead / corner stakes 25 mm aluminum hollow section, 400 mm high Side walls 25 mm aluminum hollow section, 400 mm high, foldable and removable Intermediate posts Without intermediate posts Rear wall / rear corner posts 1 pair of steel posts attached to the frame, with holder to lock the loading ramps, entry width approx. 2,430 mm Loading ramps Steel ramps, 2,300 mm long, 510 mm wide, laterally adjustable With carrying handle on the ramps With wooden covering (tip area with steel/chequer plate) With gas strut for single-person operation Operating Notes The specified gross weight is technically feasible; depending on the cargo, the gross weight may not be achievable while adhering to permissible axle, support, and kingpin loads. (Poor driving and tracking properties possible with incorrect load distribution) Country of registration / plates Germany With Dekra inspection and certificate (according to §13 EC - FGV) 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips as per ECE R 048, white at the sides, red at the rear Paintwork Frame: DB 7350 Novagrau Front bulkhead: aluminum Side walls: aluminum, anodized Loading ramps: hot-dip galvanized

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 3,650 kg, maximum load weight: 9,850 kg, overall weight: 13,500 kg, axle configuration: 2 axles, loading space length: 5,000 mm, loading space width: 2,420 mm, loading space height: 450 mm, total length: 6,900 mm, total width: 2,550 mm, total height: 1,680 mm, suspension: steel, tire size: 285/70 R19,5", tire condition: 100 %, Year of construction: 2026, - Bespoke transport solution - Configure your Fliegl vehicle to your requirements. The vehicle shown is an example. Production and equipment are carried out individually to customer specification. #Chassis – centre-axle tipping trailer - Steel welded construction, continuous rear tipping shaft with 80 mm ball-type tipping bearing - Geared support leg at front - Foldable rear support - 2 wheel chocks with holder - Steel rear underrun protection - Mudflaps at rear, full width - Quarter-shell mudguards - Lockable storage compartment for loading ramps beneath the load bed - 1 plastic tool box with removable tray, w=620/h=360/d=440 mm, lockable with a padlock - Note: side board touches the storage box when folded down - Lockable storage compartment for loading ramps beneath the load bed - Drawgear for centre-axle trailer - Drawbar with approved 40 mm tow eye - Drawbar height-adjustable via spindle, max. adjustment range 300 mm #Axles & suspension - SAF drum brake axles - "Laser-aligned axles/running gear" – reduces tyre wear and fuel consumption - Parabolic suspension with maintenance-free rubber-steel bushings and mechanical axle-load equalisation (rocker equalisation) #Wheels & tyres - 285/70 R 19.5" - Manufacturer's choice - Steel rims, factory silver #Braking system - 2-line air braking system - Spring-loaded parking brake - 2 anti-mismatch coupling heads at front, with connecting lines to the towing vehicle - ABS and ALB, with ABS socket at front, with connecting cable - Caution: this trailer may only be towed by towing vehicles that ensure the effectiveness of the ABS! #Electrics - 24 V, multi-chamber lights, yellow LED lighting on the sides - 2 white position lights at front - 2 white/red outline marker lights at rear - 2 x 7-pin anti-mismatch plugs at front, with connecting cable #Hydraulics Todpfxezd D Sco Agmoc - Three-way tipping gear, hydraulic multi-stage telescopic ram with stroke limiter and safety cable - Low-pressure cylinder up to max. 170 bar, without restrictor valve; to be retrofitted on the truck if required - Hydraulically operated via the truck's PTO - Hydraulic connection with quick-release coupling, DN 10/3, incl. connecting hose #Tipping body - Sturdy tipping body with 4 mm steel sheet floor, steel side-board structure, continuous side walls, foldable and pivot-mounted with central locking at the bottom; rear corner posts, plug-in type; tailgate foldable and pivot-mounted, with central locking at the bottom - Platform length approx. 5,000 mm, side walls with 6 hinges at the bottom - Side-board return springs - Platform width 2,420 mm - 5 pairs of lashing eyes in the floor, 5 t each #Operating notes - The stated gross vehicle weight is technically achievable; depending on the load, it may not be reached while observing the permissible axle, support and fifth-wheel loads #Country of registration/plates - Country of registration: Germany - With DEKRA inspection and certificate (in accordance with §13 EG-FGV) - 24/7 service hotline - Prepared for single-line number plate holder - Contour marking with reflective strips to ECE R 048, white on the sides and red at the rear #Paintwork - Frame hot-dip galvanised incl. passivation - "15-year warranty against corrosion perforation" - Side boards/platform painted in colour of choice - Bespoke transport solution

Condition: new, maximum load weight: 23,920 kg, overall weight: 30,000 kg, axle configuration: 3 axles, NEW VEHICLE Fliegl 3 axle low loader type DTS 300, hot-dip galvanized Total weight 24,000 kg / 30,000 kg Payload 17,920 kg / 23,920 kg Empty weight 6,080 kg Total length 10,900 mm Loading length 8,680 mm Tsdpfx Agexb Nmysmoc Loading bed 6,500 mm including 900 mm approach slope Parabolic suspension Long ramps 2,800 mm with hydraulic operation Wider widths to 3,000 mm with warning signs and rotating beacon Large lashing package with 5.0 and 10.0 ton lashing points 5 pairs of stake pockets Towing eye 40 mm Plus pre-freight / provision from the Wiesmoor storage location 1,280.00 €/ Net Rent-to-own offer: term 48 months, residual value 40%, down payment only VAT. Monthly rate: EUR 500.00

Condition: used, functionality: fully functional, machine/vehicle number: WFDFLT33902027997, empty load weight: 6,832 kg, maximum load weight: 28,168 kg, overall weight: 35,000 kg, axle configuration: 3 axles, first registration: 06/2021, loading space length: 13,460 mm, loading space width: 2,480 mm, loading space height: 2,740 mm, total length: 15,100 mm, total width: 2,550 mm, total height: 4,000 mm, suspension: air, tire size: 385/65 R22.5", tire condition: 100 %, color: black, The pictures are archive images; the vehicle may still be in use! Tsdowk Dg Nspfx Agmsc Optional equipment upon request.

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 3,250 kg, maximum load weight: 14,750 kg, overall weight: 18,000 kg, axle configuration: 2 axles, total length: 10,020 mm, total width: 2,550 mm, total height: 1,120 mm, suspension: air, tire size: 385/55 R22,5", tire condition: 100 %, Customized Transport Solution Configure your Fliegl vehicle to meet your specific requirements. The vehicle shown is an example. Production and equipment are customized according to customer specifications. *Chassis for central-axle swap trailers Fine-grained steel welded construction Front stop, longitudinally adjustable and foldable Pair of removable guide rollers, front and rear 4 container locks with sturdy 20"-based arms for 7.15 m, 7.45 m, and 7.82 m swap bodies (Note: When used in combination with the impact guard, the guard protrudes beyond the 7.15 m swap body) 1 pair of front gear-driven support legs, with straight lower section and single-sided operation on the right side 1 pair of rear gear-driven support legs, with straight lower section and single-sided operation on the right side Side impact protection set inward, for optimal clearance to the swap body supports Steel underrun protection Rear mud flaps across the entire width *Towing equipment for central-axle trailers Towing beam with certified 50 mm tow eye, freight forwarding version Towing beam clamped/bolted, easily replaceable and partially adjustable in length! Lower coupler on towing beam, free towing beam length approx. 2200 mm Folding bracket with spring support on the towing beam, for routing the connection cables to the truck *Axles + Suspension SAF disc brake axles “Laser-aligned axles/chassis” reduces tire wear and fuel consumption Air suspension without lift axle Tsdpfx Agezd Trromjc *Brake System 2-line compressed air brake system Color-coded lines for easy servicing. Air reservoir: 208 liters Spring-loaded parking brake Duomatic connection at the front, with connecting line to the tractor unit, connection at the rear right 24-volt EBS, electronic braking system with EBS connector at the front, with connecting cable, connection at the rear right Caution: The trailer may only be towed by towing vehicles that ensure the effectiveness of the ABS! With lift & lower valve, hold function in both lower and lift positions Vehicle – Vehicle Stability Control System Brake release function via a pushbutton on the vehicle next to the lift & lower valve, for releasing the brake while coupled; EBS power supply must be ensured! *Wheels and Tires 385/55 R22.5" Manufacturer's choice Steel rims, factory silver *Electrical System 24 volts, multi-chamber LED lights, yellow LED side lighting, LED license plate lighting, (Note: With certain towing vehicles, false diagnostics may occur even though the function is working properly) 2 white LED front position lights 2 white/red LED rear lane-keeping lights 1 x 15-pin connector at the front, with connecting cable, connection on the right rear Additional LED work light(s), recessed and integrated into the rear, activated via the reverse light LED work light at the front, centered between the cross members, shining toward the rear, activated via the reverse light *Country of Registration/License Plates Germany With DEKRA approval and certification (per §13 EG - FGV) 24/7 service hotline Prepared for single-line license plate holder Warning sign per ECE - 70 ADR warning sign at the rear, foldable Contour marking with reflective strips in accordance with ECE R 048, white on the sides and red at the rear *Paint finish Frame Hot-dip galvanized or painted according to customer specifications

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 3,220 kg, maximum load weight: 14,780 kg, overall weight: 18,000 kg, axle configuration: 2 axles, total length: 10,020 mm, total width: 2,550 mm, total height: 1,070 mm, suspension: air, tire size: 445/45 R19,5", tire condition: 100 %, Customized Transport Solution Configure your Fliegl vehicle to meet your specific requirements. The vehicle shown is an example. Production and equipment are customized according to customer specifications. *Chassis for swap body with central axle trailer Fine-grained steel welded construction Front stop, longitudinally adjustable and foldable 2 pairs of removable guide rollers, front and rear Swap Guard – swap body guide, in front of and behind each container lock 4 container locks with sturdy 20"-based arms for 7.15, 7.45, and 7.82 swap bodies 1 pair of front gear support legs, with straight lower section and single-sided operation on the right side 2 wheel chocks with holders Aluminum side impact protection Steel underrun protection Rear mud flaps across the entire width (not compatible with forklift mount) 4 half-shell fenders Mud flaps Spare tire mount for 1 electric bike, with wheel mounting kit Towing equipment for central-axle trailer Towing beam with certified 50 mm tow eye, freight forwarding version (not suitable for trucks with tail lifts; detailed verification may still be required on a case-by-case basis) Towing bar coupler, free towing bar length approx. 2200 mm Folding bracket with spring assistance on the towing bar, for routing the connection cables to the truck *Axles + Suspension SAF disc brake axles “Laser-measured axles/chassis” reduces tire wear and fuel consumption Air suspension *Brake System 2-line compressed air brake system Color-coded piping for easy maintenance. Air reservoir capacity: 208 liters Spring-loaded parking brake 2 non-reversible coupling heads at the front, with connecting lines to the motor vehicle, connection at FR-right EBS, Electronic Braking System with EBS connector at the front, including connecting cable, connection at FR-right Caution: The trailer may only be towed by towing vehicles that ensure the effectiveness of the ABS! With lift/lower valve, hold function in both lower and lift positions *Wheels and Tires Tjdpszd Tw Iefx Agmec 445/45 R19.5", brand selected by the manufacturer Steel rims, factory silver *Electrical system 24 volts, 4 x 3-chamber lights + 1 round backup light and + 1 round rear fog light, yellow LED lighting on the sides 2 white front position lights 2 white/red rear lane-keeping lights 1 x 15-pin connector at the front, with connecting cable, connection at the rear right 2 Additional LED work light(s) at the rear, activated via the reverse light *Country of registration/license plates Germany With DEKRA approval and certification (in accordance with §13 EG-FGV) 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips per ECE R 048, white on the sides and red at the rear *Paint finish Frame Hot-dip galvanized or painted per customer request

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 2,500 kg, maximum load weight: 15,500 kg, overall weight: 18,000 kg, axle configuration: 2 axles, total length: 9,470 mm, total width: 2,550 mm, total height: 1,260 mm, suspension: air, tire size: 385/65 R22,5", tire condition: 100 %, Customized Transport Solution Configure your Fliegl vehicle to meet your specific requirements. The vehicle shown is an example. Production and equipment are customized according to customer specifications. *Chassis with swivel turntable Fine-grained steel welded construction Fliegl “V-Stream” frame Front stop, longitudinally adjustable and foldable 2 pairs of removable guide rollers, front and rear 4 container locks with sturdy 20"-based arms for 7.15- and 7.45-meter swap bodies Note! Not suitable for 20" containers, or only possible if the container has a tunnel or opening at the front center approximately 200 mm long and 800 mm wide! Swivel frame with heavy-duty ball bearing swivel ring 2 wheel chocks with holders Aluminum side impact protection Side impact protection set inward for optimal clearance to the swap body supports Steel underrun protection Underrun protection shortened for optimal clearance to the swap body supports; lighting system mounted in a protected position Half-shell fenders Rear mud flaps across the entire width *Trailer Coupling Device (Turntable) Towing fork with certified 40 mm tow eye Spring-loaded towing fork height adjustment *Axles + Suspension SAF disc brake axles “Laser-measured axles/chassis” reduces tire wear and fuel consumption Air suspension *Brake System 2-line compressed air brake system; color-coded lines for easy servicing. Air reservoir: 208 liters Spring-loaded parking brake 2 non-reversible coupling heads at the front, with connecting lines to the tractor unit, EBS, Electronic Brake System with EBS connector at the front, with connecting cable, Caution: The trailer may only be towed by towing vehicles that ensure the effectiveness of the ABS! With lift/lower valve, hold function in both lower and lift positions *Wheels and Tires 385/65 R22.5" Manufacturer’s choice Steel rims, factory silver, ET 120 *Electrical System 24 volts, multi-chamber lights, yellow LED side lighting 2 white front position lights 2 white/red rear lane-keeping lights 2 x 7-pin reverse-proof connectors at the front, with connecting cable, 2 additional LED work lights at the rear, activated by the reverse light 1 LED work light at the front, centered between the cross members, shining toward the rear, activated by the reverse light *Country of Registration/License Plates Germany with DEKRA approval and certification (in accordance with §13 EG - FGV) 24/7 service hotline prepared for single-line license plate holder Tedpfjzd U Uuox Agmjc Contour marking with reflective strips per ECE R 048, white on the sides and red at the rear *Paint finish Frame Hot-dip galvanized or painted according to customer specifications Customized transport solution Configure your Fliegl vehicle to meet your requirements. The vehicle shown is an example. Production and equipment are customized according to customer specifications.

Condition: used, functionality: fully functional, machine/vehicle number: WFDFLT34002026850, empty load weight: 5,875 kg, maximum load weight: 33,125 kg, overall weight: 39,000 kg, axle configuration: 3 axles, first registration: 05/2020, loading space length: 13,650 mm, loading space width: 2,480 mm, loading space height: 2,790 mm, total length: 13,850 mm, total width: 2,550 mm, total height: 4,000 mm, suspension: air, tire size: 385/65 R22,5", tire condition: 75 %, color: silver, - Chassis: semi-trailer, general haulage - Fine-grain steel welded frame, fifth-wheel plate with replaceable 2" kingpin - Slightly tapered outer frame, new design, "Load-Lock-Profil" for strap lashing - 24t 2-speed landing legs, single-side operation, straight foot, no shift compensation - Note: rear corner clearance / swing radius approx. 1930 mm - Rear pull-out ladder - 2 side door retainers - 2 wheel chocks with holder - Aluminium side impact protection - Galvanised steel rear underrun protection - Quarter-shell mudguards front/rear of axle unit - EC anti-spray flaps on 3rd axle - Rear corner impact protection - 1 lockable plastic toolbox, 600x425x460 mm # Axles & Suspension - 3x BPW drum brake axles - Axle/chassis laser-aligned - lower tyre wear & fuel use - Air suspension - Axle 1: auto lift axle, forced lowering, traction assist via "3x brake pedal" (active up to 30% axle overload, max. 25 km/h) # Braking System - 2-line air brake system - Colour-coded lines for easy servicing - Spring-loaded parking brake - 2 mismatch-proof coupling heads, front, no hose - 24V EBS with front socket, no cable - Caution: tow only with tractor units ensuring ABS effectiveness! - Raise & lower valve - Vehicle stability system # Wheels & Tyres - 385/65 R22.5" - Steel wheels, factory silver # Electrics - 24V multi-chamber lamps, yellow LED side markers - 2 white LED front position lamps - 2 white/red outline marker lights, rear - 2x 7-pin mismatch-proof front sockets, no cable # Floor - Screen-printed plywood approx. 30 mm, longitudinal bearers, forklift axle load up to 7,100 kg # Front Wall / Front Corner Posts - 2,580 mm high, box-section steel corner posts, front curtain release, "Crash-Blocker", steel impact guard approx. 140 mm high, lower inside # Centre Posts Tsdpfozzkrdsx Agmsc - 3 pairs sliding posts, full-length adjustable, 4 insertion pockets + long bottom pocket (bottom pocket omitted with side boards) - 3 pairs of post positions # Insertion Slats - 5 rows of aluminium insertion slats # Rear Wall / Rear Corner Posts - Steel rear corner posts to roof edge, curtain fixing with round tube & tensioning ratchet - 2-leaf rear barn doors, each with 2 internal rod locks # Curtain - Curtain with welded-in horizontal/vertical straps - Stainless steel tensioning locks # Roof - Sliding roof, rear bow lifts up, curtain slides rear-to-front, L-section roof rail (automotive-grade), internal width approx. 2,490 mm, white curtain - Non-elastic roof, minimal roof rail deflection when loading - Optimised rain channel at rear, above doors on end bow # Operating Notes - When forming a combination, observe the legal max. overall vehicle height! - If overall height exceeds 4,000 mm, note the following: - The haulier is liable for any damage incurred. - The delivery driver must obtain their own permit under § 29 StVO - We accept no liability for vehicle delivery/transfer. # Country of Registration / Plates - Germany - DEKRA inspection & report (per §13 EC-FGV) - 24/7 service hotline - Fliegl body-strength certificate to EN 12642 XL (payload up to 27,000 kg) - Prepared for single-row plate holder - Warning plate per ECE-70 - Reflective strips: white, continuous along bottom of side curtains, top corners (with side boards fitted: strip at bottom, on boards) - Reflective strips: red, all around rear doors

Condition: new, functionality: fully functional, machine/vehicle number: WFDFLT10401014064, empty load weight: 1,500 kg, maximum load weight: 2,300 kg, overall weight: 3,800 kg, axle configuration: 1 axle, loading space length: 2,000 mm, loading space height: 1,000 mm, total length: 4,300 mm, total width: 2,460 mm, suspension: steel, tire size: 235/75 R17,5", tire condition: 100 %, color: green, - Single-axle container trailer - Type EPS 38 for diesel generator set body - Multiple units available - Please note: archive images! #Chassis single-axle trailer - Welded construction in fine-grain steel - Generator set secured by bolted connection - Reinforced front jockey wheel, mechanically adjustable in length, folding at the bottom - 1 pair of 2-speed landing legs at rear, with straight lower section, left and right operated independently - 2 wheel chocks with holders - Aluminium side underrun protection, painted RAL 6031 bronze green matt - Steel rear underrun protection, painted RAL 6031 bronze green matt - Mudguards in front of and behind the axle, with sheet-metal cover on top - With anti-spray mud flaps - 2 pairs of lashing cut-outs, 1 pair front and 1 pair rear, recessed into the cross members, each rated 3 t for loading the trailer, marked (sticker) - 4 pairs of ferry lashing eyes, marked yellow - Lashing point sticker on each lashing eye - Rosette-pattern perforated steel plate on both sides outside next to the generator set, pull-out ladder on both sides - Holder for 2 x 20 l fuel cans on the vehicle frame, right-hand side in direction of travel - Central lashing point sticker - Steel storage box at front, recessed into the floor, with drainage holes, lined with perforated rubber mat, lockable lid #Towing device single-axle trailer - Drawbar with tested reversible towing eye: 40 mm / NATO eye (changed by turning) - Drawbar height-adjustable via spindle; nut for spindle mounting bolt at bottom, right-hand side in direction of travel - Parking sockets for electrics/EBS and air #Axle + suspension - BPW axle with taper roller bearings and S-cam brake - Axle/running gear laser-aligned – reduces tyre wear and fuel consumption - Parabolic suspension with maintenance-free steel-rubber bushes #Wheels and tyres - 235/75 R 17.5 - Make at manufacturer's discretion - Steel rims, factory silver #Braking system - Dual-line air brake system - Spring brake actuator parking brake - 2 non-interchangeable coupling heads at front, with connecting lines to the towing vehicle - Yellow connection on the left and red connection on the right in direction of travel Tjdpozazrtjfx Agmec - ABS/EBS electronic braking system with EBS connector at front, with connecting cable - EBS modulator mounted in a protected position - Caution: the trailer may only be towed by towing vehicles that ensure the effectiveness of the ABS! - Vehicle stability system #Electrics - 24 V, multi-chamber lamps, yellow LED side lighting - ADR-compliant electrics with certificate - 2 white front position lamps and reflectors - 2 white/red rear outline marker lights - 1 x 15-pin socket + 1 x detachable 15-pin coiled cable at front #Registration / plates - Country of registration: Germany - With DEKRA inspection and expert report (acc. to §13 EG-FGV) - 24/7 service hotline - Prepared for single-line number plate holder - Contour marking with reflective tape acc. to ECE R 048, rear only, white - Warning plate acc. to ECE-70 #Paintwork - Frame RAL 6031, bronze green matt - Drawbar in frame colour

Condition: used, empty load weight: 8,940 kg, maximum load weight: 31,060 kg, overall weight: 40,000 kg, axle configuration: > 3 axles, first registration: 03/2026, loading space length: 10,250 mm, loading space width: 2,520 mm, loading space height: 930 mm, suspension: air, tire size: 235/75R17.5, color: silver, mileage: 1,001 km, gearing type: other, driver cabin: other, Equipment: ABS, Vehicle location: Bovenden, 4 axles, turntable, air suspension, ABS (anti-lock braking system), can be widened to 3m, lashing eyes, hydraulic ramps, rear support, side aluminum wheel guards, twin tires, wheel recesses. Tedpfx Agozr Rmiemjc Superstructure: 4-axle low-bed trailer with wheel recesses, excavator arm recess, and hydraulic ramps. Galvanized, 4x 10t axle, drum brakes, technically permissible total weight 40,000 kg, can be widened to 3000mm! Length of upper platform approx. 2800mm! Length of lower platform approx. 7450mm! Ramp length approx. 2900mm! Loading height of front wheel recess approx. 550mm! Loading height of rear wheel recess approx. 620mm! Length of front wheel recess approx. 1600mm! Length of rear wheel recess approx. 600mm! ACCESSORY INFORMATION WITHOUT GUARANTEE, subject to changes, prior sale, and errors!

Condition: used, Year of construction: 2005, -AUCTION MACHINE- ab-auction PFW 15500 Eckart Pump Tanker Drawbar Working width 15 meters PTO shaft Tank volume 15,500 liters GFK tank design ALB control unit Tandem axle Leaf springs Trailing steering Maximum speed 40 km/h Tires 750/65 R30.5 K80 hitch PTO 1,000 rpm Lighting system Trailing hose distributor Drip stop Partial width distribution Hydraulic frame folding Hydraulic height adjustment You can bid on this machine online. The starting price is 9,900.00 EUR excluding VAT. Register for free and start bidding. Click here to go to the auction: ----- ----- Exciting Online Auction! Start bidding NOW! Tsdpfoyri T Asx Agmec ab-auction

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 3,900 kg, maximum load weight: 20,100 kg, overall weight: 24,000 kg, axle configuration: 3 axles, total length: 9,200 mm, total width: 2,550 mm, total height: 1,180 mm, suspension: air, tire size: 385/55 R22,5", tire condition: 100 %, color: original, Year of construction: 2026, Customized transport solution Configure your Fliegl vehicle according to your requirements. The vehicle shown is an example only. Production and equipment are customized according to customer specifications. # Chassis – Turntable Swap Body Trailer Heavy-duty fine-grain steel welded construction Adjustable and foldable front stop 2 pairs of removable guide rollers (front and rear) 4 container twist locks with reinforced outriggers on a 20" base for 7.15 m and 7.45 m swap bodies Heavy-duty turntable with ball-bearing ring 2 wheel chocks with holders Aluminium side underrun protection Steel rear underrun protection Half-shell mudguards (front and rear) 2 lockable stainless steel toolboxes (600 × 400 × 500 mm) with polished doors 1 pair of double LED illuminated rear warning panels, extendable to 3,000 mm Electrical connector prepared for customer-installed front warning panels # Drawbar Drawbar with certified 40 mm towing eye Mechanically adjustable drawbar length (6 × 100 mm positions), approx. 1,900–2,500 mm Spring-assisted drawbar height adjustment # Axles + Suspension BPW disc brake axles with 430 mm brake discs Laser-measured axle/chassis alignment for reduced tyre wear and fuel consumption Air suspension with raise/lower valve # Wheels and Tyres 385/55 R22.5 tyres (manufacturer's choice) Factory silver steel rims # Brake System Dual-line compressed air braking system Spring parking brake 2 non-interchangeable air couplings with connecting lines to the towing vehicle Electronic Braking System (EBS) with front connector and connecting cable Note: Trailer may only be operated with towing vehicles that ensure full ABS functionality. Tedpfx Agjzndmzemoc # Electrical System 24 V electrical system Multi-chamber lighting Yellow LED side marker lights 2 white front position lights 2 white/red rear outline marker lights Removable rotating beacon 1 LED rear work light, activated via reverse gear 2 LED side work lights (left and right), activated via reverse gear 1 × 15-pin front connector with connecting cable # Registration Prepared for registration in Germany DEKRA approval and certificate according to §13 EC-FGV 24/7 service hotline Prepared for single-line number plate holder ECE R48 reflective contour markings (white sides, red rear) # Finish Frame hot-dip galvanized with passivation, including 15-year anti-corrosion warranty Drawbar KTL-coated in black Please note: Archive photos shown – actual vehicle may differ.