Used Fliegl Zts Trailers for sale (314)

Condition: new, machine/vehicle number: 2dee9cc4124b79c4820f5c3cf, overall weight: 35,000 kg, axle configuration: 3 axles, tire size: 385/65 r22.5, Further information Fine-grained steel welded construction, saddle plate with replaceable 2 , kingpin, outer frame slightly inclined new design with Load-Lock profile for tensioning strap attachment, 24 to. 2-speed support winch, single-sided operation, with straight lower section, without thrust compensation Note: Free support leg corner dimension or free swing-through radius to the rear approx. 1930 mm, pull-out ladder at the rear, door stop at the side, 2 wheel chocks with holder, Aluminium side collision protection, galvanized steel underride guard, quarter-shell mudguards in front of and behind axle unit, with anti-spray flaps in accordance with EC, impact protection at the rear SAF disc brake axles with 430 mm disc diameter, axle/chassis laser-measured Reduction in tire wear and fuel consumption, air suspension 2-line compressed air brake system, colored cable routing for easy servicing, spring-loaded parking brake, 2 swap-proof coupling heads at the front, without connecting cable, EBS, electronic brake system with EBS socket at the front, without connecting cable, Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS, with lift & lower valve, vehicle stability system 385/65 R22.5 tires of the manufacturer's choice, steel rims, factory silver 24 volt, multi-chamber lights, amber LED lighting at the sides, 2 white position lights at the front, 2 white/red lane departure lights at the rear, 2 x 7-pin interchangeable sockets at the front, without connecting cable, Floor: Screen printing plates approx. 30 mm thick, on longitudinal beams for high point load capacity for forklift axle load up to max. 7100 kg Front bulkhead / corner stanchions: 2,580 mm high, steel corner stanchions in volume design, release device for side tarpaulin on bulkhead, crash blocker, bottom inside at approx. 140 mm height with steel impact protection Center stanchions: 3 pairs of sliding stanchions can be moved along the entire length, with 4 insertion pockets and long pocket at the bottom, 3 pairs of stanchion positions Insertion slats: 5 rows of wooden insertion slats Rear wall / rear corner stanchions: Rear steel corner stanchions up to the lower edge of the roof, attachment for tarpaulin with round tube and tarpaulin tensioning ratchet, rear portal doors, 2-leaf with 2 internal espagnolette locks each Tarpaulin: tarpaulin with welded horizontal and vertical straps, stainless steel tensioning fasteners Roof: Sliding roof, rear end lift can be folded up, with roof can be slid from rear to front, L-shaped roof rail for automotive industry, internal width between the roof rails, approx. 2,490 mm, tarpaulin color: white, 400 Roof non-elastic, hardly any deflection of the roof rail when loading and unloading, optimum rain strip at the rear, at the top of the end bows, above the doors Germany, test approval according to EC 2007/46, 24/7 service hotline, Fliegl manufacturer's certificate for structural strength according to EN 12642 XL, prepared for single-line license plate holder, warning sign according to ECE - 70, reflective strips: white, continuous on the side tarpaulins at the bottom and at the top in the corners (if visible drop sides, then the strip at the bottom, on the drop sides), reflective strips: red, all-round on the rear portal Ljdsi Riy Tepfx Acyshb Frame DB 7350 nova grey, 10-year warranty against rusting through, support legs coated black, front corner stanchions hot-dip galvanized, front wall aluminium, rear corner

Condition: used, machine/vehicle number: 9a9c8ebe1f7e791f4fc6f94e6, empty load weight: 2,620 kg, maximum load weight: 15,380 kg, overall weight: 18,000 kg, axle configuration: 2 axles, first registration: 04/2019, tire size: 385/65 r22,5, Year of construction: 2019, Further information Welded fine-grained steel construction, front stop, longitudinally adjustable and foldable, pair of removable guide rollers, front and rear, pair of removable guide rollers, additional 4 container locks with sturdy outriggers on 20-base for swap bodies 7.15 and 7.45, turntable with strong ball bearing slewing ring, wheel chocks with holder Aluminum side bumpers, steel underride guard, quarter-shell mudguards at the front and half-shell mudguards at the rear 1 spare wheel holder for 1 e-wheel, with wheel fastening set in basket design Drawbar with tested 40 mm drawbar eye, drawbar height adjustment via spring BPW disc brake axles, axle/chassis laser-measured Reduction in tire wear and fuel consumption, air suspension 2-line compressed air brake systemColor-coded line routing for easy servicing. Air supply 208 liters Lhedpfxei Riz Ho Acysb Spring-loaded parking brake, 2 swap-proof coupling heads at the front, with connecting lines to the motor vehicle, EBS made by Wabco, electronic brake system with EBS plug at the front, with connecting cable, (Attention: The trailer vehicle may only be towed by towing vehicles that guarantee the effectiveness of the ABS!) with lifting & lowering valve, holding function in the lowering / lifting position in each case 24 volt, 4 x 3 chamber lights + 1 round reversing light + 1 round rear fog light, amber LED lighting at the side, 2 white position lights at the front, 2 white/red lane departure lights at the rear, 1 x 15-pin plug at the front, with connecting cable, 1 additional LED work light(s) at the rear, switched via reversing light, 1 LED work light at the front in the middle between the beams, radiating to the rear, switched via reversing light Country of registration: Germany, with Dekra approval and certificate (according to §13 EG - FGV), prepared for single-line license plate holder, contour markings with reflective strips according to ECE R 048, white at the sides and red at the rear

Condition: new, machine/vehicle number: 5067caac5acaa655d1d94bd2d, empty load weight: 760 kg, maximum load weight: 1,740 kg, overall weight: 2,500 kg, axle configuration: 1 axle, tire size: 235 / 75 r 17,5, Further information Chassis central axle trailer Fine-grained steel welded constructionincl. 4 mounting points for IBC containers if technically possible Drawing approval required from the customer if ordered! 2 side members as double T-beams for subsequent self-supporting superstructure with front cross member 2 pairs of lashing eyes for lashing the IBC container Telescopic support foot at the front Ledpfx Asi Ri Anjcyjhb Wheel chocks with holder Mudguards without side bumpers Steel underride guard Towing device central axle trailer Towbar with tested 40 mm towing eye, forwarding version Height-adjustable drawbar via spindle, max. adjustment range 250 mm Axles + suspension GFA or BPW axle of the manufacturer's choice, with angular roller bearings and S-cam brake Axle/chassis laser-measured Reduction in tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings Wheels and tires 235 / 75 R 17,5 at the manufacturer's choice Factory silver steel rims Brake system 2-line compressed air brake system Spring-applied parking brake 2 non-interchangeable clutch heads at the front, with connecting lines to the motor vehicle, without ABS, but with mechanical ALB, then max. 60 km/h approval Electrical system 24 volt, multi-chamber lights, without amber LED lighting at the side 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin interchangeable plugs at the front, with connecting cable, Country of registration / plates Country of registration: Germany with Dekra approval and certificate (according to §13 EG - FGV) 24/7 service hotline Prepared for single-line license plate holder Paint finish Frame DB 7350 nova gray10-year warranty against rusting through Attention! These are archive pictures.

Condition: new, machine/vehicle number: 74dd481d88dffaf9218e6ee58, empty load weight: 5,150 kg, maximum load weight: 29,850 kg, overall weight: 35,000 kg, axle configuration: 3 axles, tire size: 385/65 r22,5, Further information Chassis tipper semi-trailer Fine-grained steel welded construction, in basic lightweight design, fifth wheel plate with interchangeable 2 kingpins Patented curved front end Telescopic support in the middle, unhitching with load not possible, when unhitched the vehicle must be at an angle to the rear. Wheel chocks with holder Underride guard, foldable Half-shell mudguards Integrated mudguard holder Stone-repellent surface with anti-spray flaps on last axle only Tarpaulin pole with bracket Tow hook at the rear Axles+suspension SAF disc brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Axles in off-road version, Air suspension 1st axle automatic lift axle, including forced lowering and starting aid, actuation of 3x brakes (starting aid is functional up to an axle load excess of 30% and up to a speed of max. 25 km/h) Hot-dip galvanized lift axle mechanism 10-year warranty against rusting through Brake system 2-line compressed air brake systemColor-coded cable routing for easy servicing. Spring-loaded parking brake 2 interchangeable front clutch heads, without connecting line EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve Vehicle stability system Automatic tilt lowering with shut-off valve Wheels and tires 385/65 R22.5 Steel rims, factory silver Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red rear lane departure lights Ledoi Ri A Iepfx Acyshb 2 x 7-pin interchangeable sockets at the front, without connecting cable Hydraulics Low-pressure cylinder max. 170 bar, smallest stage hard-chlorinated, with HDK screw socket, fixed part, NW 48 mm (without hose connection). Hydraulic actuation via truck power take-off Troughs Round steel body in Stone Master design made of highly wear-resistant HB 400/450 steel. Sloping front wall with external hydraulic en with access to front wall. Greenline - conical and aerodynamic body shape Bucket and brush holder on the outside of the front wall. Membrane rear wall Rear wall as swing flap with double-jointed hinge, resting on the outside with double hook lock. 2 clamping screws with toggle fasteners at the bottom side. Side walls 4 mm thick throughout, base 4/5 mm thick, wear and weight-optimized design, Standing platform with step, connection plate for air/electric and brake with large clearance for optimum operability. Roller tarpaulin on one side for depositing in FR-right, with central locking in FR-left Operating instructions For salt, lime, etc. We recommend a tipping cylinder with a hard chrome-plated piston rod so that it is not attacked by the material and rusts. The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Germany Test approval according to EC 2007/46 Body strength according to EN 12642 24/7 service hotline Prepared for single-line license plate holder Warning sign according to ECE - 70 Contour markings with reflective strips to ECE R 048, white at the sides and red at the rear Paint finish Frame DB 7350 nova gray10-year warranty

Condition: new, machine/vehicle number: ac4e8c4b4fd368b58adf3c5d3, empty load weight: 2,860 kg, maximum load weight: 7,040 kg, overall weight: 9,900 kg, axle configuration: 2 axles, tire size: 235 / 75 r 17,5, Further information Chassis central axle tipping trailer Welded steel construction, continuous tipping shaft at the rear with 80 mm ball tipping bearing Gear support foot at the front Folding rear support 2 wheel chocks with holder Steel underride guard Rear spray flaps across the entire width (not in conjunction with forklift bracket) Quarter-shell mudguards Lockable storage space for access ramps underneath the loading area 1 pair of ramps 3,000 mm long, 360 mm wide, load capacity per pair 4,000 kg (suspension bar for ramps at the rear) Towing device for central axle trailer Towing bar with tested 40 mm towing eye Height-adjustable drawbar via spindle, max. adjustment range 300 mm Axles + suspension GFA or BPW axles of the manufacturer's choice, with angular roller bearings and S-cam brake Axle/chassis laser-measured Reduction in tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation (rocker compensation) Wheels and tires 235 / 75 R 17,5 manufacturer's choice Factory silver steel rims Brake system 2-line compressed air brake systemColor-coded cable routing for easy servicing. Hand spindle parking brake Integral air reservoir ABS and ALB, with ABS plug at the front, with connecting cable, Ljdpsi Ri Eiofx Acyehb Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! 2 swap-proof coupling heads at the front, with connecting cables to the motor vehicle, Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin non-interchangeable plugs at the front, with connecting cable, Hydraulics Three-way tipping mechanism, hydraulic multi-piston press with lift limiter and safety cable, Low-pressure cylinder up to max. 170 bar, without throttle. If necessary, this must be retrofitted to the truck. Hydraulic connection with SVK plug NW 10/3, incl. connection hose Hydraulic actuation via truck power take-off Tilting bridges Sturdy tipper body with 4 mm sheet steel floor, steel side wall structure, continuous side walls, hinged and non-oscillating without central locking at the bottom. Rear corner stanchions pluggable. Rear wall can be folded down and pivoted, with central locking at the bottom. Platform length approx. 4,500 mm, side walls with 5 hinges at the bottom. Platform width 2420 mm 5 pairs of lashing eyes in the floor, 5 tons each Operating instructions The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Country of registration: Germany with Dekra approval and expert opinion (according to §13 EG - FGV) 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white at the sides and red at the rear Paintwork Hot-dip galvanized frame incl. passivation 15-year warranty against rusting through Dropside/bridge RAL 9010 pure white Note! Bridge inside only primed if painted bridge version! Attention! These are archive pictures. Also available IMMEDIATELY with 5m bridge!

Condition: new, machine/vehicle number: 1eb6bdba4d54d87ab018b84c2, empty load weight: 3 kg, maximum load weight: 14 kg, overall weight: 18 kg, axle configuration: 2 axles, tire size: 445/45 r19,5, Further information Chassis Wechel central axle trailer Fine-grained steel welded construction Front stop, longitudinally adjustable and foldable Pair of removable guide rollers, front and rear 4 container locks with sturdy outriggers on 20-basefor swap bodies 7.15 and 7.45 1 pair of gear support legs at the front, with straight lower section and single-sided operation in FR right 2 wheel chocks with holder Aluminum side bumpers Steel underride guard Half-shell mudguard Spray flaps Towing device central axle trailer Towbar with tested 50 mm towing eye, forwarding agent version (not suitable for trucks with tail lift, or exact testing still required in the event of an order) Without length adjustment of drawbar Axles + suspension SAF disc brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Air suspension Brake system 2-line compressed air brake systemColor-coded line routing for easy servicing. Air supply 208 liters Spring-applied parking brake Lsdpfsi Ri Itex Acyjhb Duomatic connection at the front, with connection line to the motor vehicle, connection in FR-left EBS, electronic braking system with EBS plug at the front, with connecting cable, connection in FR right-hand side Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve, holding function in both lowering / lifting position Wheels and tires 445/45 R19.5 tires of the manufacturer's choice Steel rims, factory silver Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable plugs at the front, with connecting cable, connection in FR right-hand side LED work lights on both sides (switched via reversing light) LED worklights at the front, centered between the carriers, radiating to the rear, switched via reversing light Operating instructions Special approval required if the overall length of the train exceeds 18,750 mm. Observe country-specific approval regulations. Country of approval / plates Germany with Dekra approval and expert opinion (according to §13 EG - FGV) 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white at the sides and red at the rear Paint finish Frame DB 7350 nova gray10-year warranty against rusting through Attention: Archive pictures!

Condition: new, machine/vehicle number: ee3256d63dd23b3ad1bdf9ab0, empty load weight: 10,280 kg, maximum load weight: 13,720 kg, overall weight: 24,000 kg, axle configuration: 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction Turntable with powerful ball bearing slewing ring Folding rear support 2 wheel chocks with holder Aluminum side bumpers Rear splash guards across the entire width Quarter-shell mudguards in front of 1st axle Excavator trough above the rear axles starting to the rear, approx. 1800 mm long, approx. 650 mm wide and approx. 150 mm deep, 2 pairs of lashing holes each 5 tons in the excavator trough on the side of the longitudinal frame approx. 300 mm from the front and approx. 200 mm in front of the rear slope 1 storage box on offset recessed in the floor with cover, W=720 mm/ L=520 mm / D= 170 mm 1st pair of wheel recesses recessed in the low bed in the tramline area after the offset, sloping towards the entrance, length at the bottom approx. 1600 mm, approx. 400 mm deep. Note! Frame in the main beam area 400 mm higher than wheel recess.2nd pair of wheel recesses between the axles in the drop center in the tramline area, slanted towards the entrance, length at the bottom approx. 600, approx. 300 mm deep. Note! Frame in main beam area 300 mm higher than wheel recess. Wheel well cover can be pulled out from the main frame, with wooden inserts. Distance from main frame beam to beam outside approx. 1280 mm (wheel well area) Widenings extendable to 3,000 mm, foldable on the wheel recess extensions (widening not in the rear slope and not in the wheel recesses below) (track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Storage compartment for wooden planks in the middle of the cargo bed or under the cargo bed if technically possible Wooden planks 70 mm for widening to 3000 mm Low loader lashing eyes 1 pair of front lashing eyes recessed on offset, 5 tons each 8 pairs of lashing rings at the top and sides of the outer frame, 10 tons each 2 x at the front on the offset 6 x in the low bed First lashing eye 250 mm from the front and last max. 250 mm from the rear, distance between lashing eyes not greater than 1100 mm 5 pairs of ring lashing eyes embedded in the outer frame, 5 tons each (can be converted to stake pockets) Trailer drawbar Turntable Drawbar with tested 50 mm drawbar eye with 8° inclined drawbar eye Lhodpfx Aoi Ri I Necyob Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Air suspension with lift & lower valve can be operated separately at the front and rear Wheels and tires 235 / 75 R 17,5 at the manufacturer's choice Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-loaded parking brake Trailer Infocenter, for displaying vehicle data such as axle load (no calibrated scales) and odometer Axle load detection via EBS-Canbus signal, for display in the driver's cab, truck must be prepared accordingly, no truck installation (no calibrated scales) Vehicle - driving stability system Duomatic connection at the front, with connecting cable to the truck, EBS, electronic braking system with EBS plug at the front, with connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrical system 24 volt, multi-chamber lights in LED with resistor, amber LED lighting on the side, license plate lighting in LED, (Note! with certain towing vehicles, misdiagnoses may occur even though the function is given) 2 white front position lights in LED 2 white/red rear lane departure ligh

Condition: used, machine/vehicle number: a6d448c42c302ffbdb6a9c40f, empty load weight: 4,480 kg, maximum load weight: 13,520 kg, overall weight: 18,000 kg, axle configuration: 2 axles, first registration: 05/2014, tire size: 445/45 r19,5, Year of construction: 2014, Further information Fine-grained steel welded construction 1 gear support foot at the front, with straight lower section and single-sided operation in FR right Wheel chocks with holder, aluminum side bumpers, steel underride guard Half-shell mudguards protrude slightly over the main frame, bumpers at the rear Tandem trailer towing device Towbar with tested 50 mm towing eye, forwarding agent version, under-coupler towbar Axles + suspension Lsdpfx Aconi Udzsyehb BPW disc brake axles, manufacturer's choice Air suspension with lift & lower valve Wheels and tires 445 / 45 R 19.5, manufacturer's choice, steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake, Duomatic connection at the front, with connecting cable to the motor vehicle, EBS, electronic braking system with EBS plug at the front, with connecting cable Make Haldex, Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Floor: Platform length approx. 7,300 mm, screen-printed floor Front wall: aluminum approx. 1,200 mm, steel corner stanchions in volume design Electrical system 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white position lights at the front 2 white/red lane departure lights at the rear 1 x 15-pin plug at the front, with connecting cable Approval / plates Country of registration: Germany, with Dekra approval and certificate 24/7 service hotline, prepared for single-line license plate holder, contour marking with reflective strips to ECE R 048, white at the sides and red at the rear

Condition: used, machine/vehicle number: 28be789c7675b811b702c6cb3, empty load weight: 6,000 kg, maximum load weight: 20,000 kg, overall weight: 26,000 kg, axle configuration: 2 axles, first registration: 04/2018, tire size: 205 / 65 r 17,5, Further information Welded fine-grained steel construction, saddle plate with replaceable 2 king pins Reinforcer mounting point for gallows mounting and with sturdy grinding plates drum profile made of flat steel underneath the outer frame. Outer frame slightly inclined with Load-Lock profile for attaching tension beltsNote! To attach the belts in conjunction with drop sides, the drop sides must be opened! 24 to. 2-speed support winch, single-side operation, with straight lower section, without thrust compensation Wheel chocks with holder, aluminum side bumpers, offset inwards as far as technically possible, steel underride guard, as much ground clearance as possible, quarter-shell mudguards in front of and behind each axle, suspension strip for aluminum ramps at the rear, plastic toolbox, with shelf, w=620/h=360/t=440 mm, lockable with a padlock. (lock not included in scope of delivery) SAF drum brake axles, with axle stopsAxle distance 1600 mm, air suspension with lifting & lowering valve 205 / 65 R 17.5, twin steel rims, factory silver 2-line compressed air brake system, spring-loaded parking brake, 2 interchangeable front coupling heads, without connecting cable, EBS, electronic brake system with EBS socket at the front, without connecting cable, Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! 24 volt, multi-chamber lights, amber LED lighting integrated in outer frame profile at the side, offset inwards by approx. 25 mm, 10 lights per side 2 white position lights at the front, protected, 2 white/red lane departure lights at the rear, additional LED work light(s) at the rear, switched via reversing light 2 x 7-pin and 1 x 15-pin swap-proof sockets at the front, without connecting cable Screen printing plates approx. 30 mm thick, for high point load capacity for forklift axle load up to max. 5,600 kg Special floor installation: test of new profiles, without bolting Steel/checker plate covering in the wheel arch area, front wall/front stanchions, 25 mm aluminum hollow profile, approx. 800 mm high, steel corner stanchions in volume design, with viewing windows on both sides. Lsdpfx Acomp Ug Dsyehb Approval country: Germany, with Dekra approval and certificate (according to §13 EG - FGV), 24/7 service hotline, prepared for single-line license plate holder, contour marking with reflective strips according to ECE R 048, white at the sides and red at the rear

Condition: used, machine/vehicle number: 41b5b53ab0b527fda1f0f26fe, empty load weight: 6,500 kg, maximum load weight: 28,500 kg, overall weight: 35,000 kg, axle configuration: 3 axles, first registration: 02/2020, tire size: 445/45 r19,5, Further information The pictures are archive pictures, the vehicle may still be in use! Chassis saddle forwarding Fine-grained steel welded construction, with preload slight pre-tensioning in the neck area, saddle plate with replaceable 2 kingpins PRO SLIDE, additional front skid plate for protection when saddling up Slightly angled outer frame with Load-Lock profile for attaching tensioning straps Note! To attach the straps in conjunction with drop sides, the drop sides must be opened! 24 to. 2-speed support winch, single-sided operation, with semicircular lower section and straight connecting plate, with thrust compensation Note: Free support leg corner dimension or free swing radius to the rear approx. 1930 mm 1 pair of gear support legs at the rear, with straight lower section and single-sided operation in FR right Pull-out ladder at the rear Side door retainer Wheel chocks with holder Aluminium side bumper Galvanized steel underride guard Quarter-shell mudguards in front of 1st axle and behind each axle With anti-spray flaps behind each axle Heavy blocker rear transverse bumper + side roller bumpers Heavy-duty pallet stop bolted on both sides, approx. 15 - 20 mm high, with lashing option every 200 mm, loading height reduced by approx. 15 - 20 mm Plastic tool box, with drawer and shelf, w=650 / h=520 / d=670 mm, lockable with a padlock (lock not included) Storage compartment for 16 insertable slats, one-sided in FR-left, below loading area Axles+suspension BPW disk brake axles with 370 mm disk diameter, Axle/chassis laser-measured Reduction in tire wear and fuel consumption Air suspension Rear loading height approx. 1200 mm when raised (air suspension on truck lowered to approx. 910 mm semi-mounted height) without lift axle Brake system 2-line compressed air brake system Colored line routing for easy service. Spring-applied parking brake Duomatic connection at the front, without connecting cable EBS make Wabco-E, electronic brake system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lift & lower valve + auto-reset function Vehicle stability system Wabco ramp starting aid, TailGUARD with 3 ultrasonic sensors at the rear of the vehicle Electrical system 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin and 1 x 15-pin interchangeable front sockets, without connecting cable Reversing camera system with color flat screen monitor, with wireless connection to the screen, screen with suction cup mount and power supply via 24 volt vehicle socket Floor Screen printing plates approx. 30 mm thick, on longitudinal beams for high point load capacity for forklift axle load up to max. 7100 kg Rear area with heavy-duty floor approx. 1800 mm long In the rear area, steel/ checker plate flooring is fitted over a length of approx. 300 mm (protrudes slightly). Front wall / front corner stanchions 2,580 mm high, steel corner stanchions in volume design, release device for side tarpaulin on bulkhead, Crash blocker, bottom inside at approx. 140 mm height with steel impact protection Center stanchions 3 pairs of sliding stanchions can be moved along the entire length, with 4 insertion pockets and a long pocket at the bottom. 3 pairs of stanchion positions Insertion slats Lodsqhiyxjpfx Acyehb Wooden slats Additional row of aluminum V-slats Vario steel slats, in conj

Condition: new, machine/vehicle number: c13a96854ea37997845c1bf36, empty load weight: 6,860 kg, maximum load weight: 28,140 kg, overall weight: 35,000 kg, axle configuration: 3 axles, tire size: 235/75 17,5, Further information Chassis saddle forwarding Fine-grained steel welded construction, fifth wheel plate with replaceable 2 king pins Suspension strip for feeder ramps on the rear extension across the entire width, outer edge chamfered to prevent damage. Frame in reinforced design for vehicle loading (up to outer frame) Outer frame with Load-Lock profile approx. every 400 mm, for lashing strap attachment 10 pairs of lashing mushrooms embedded in the top/outside of the outer frame, 10 tons each, starting from the neck area 24 t. 2-speed support winch, single-side operation, with straight connecting plate 2 wheel chocks with holder Aluminium side bumper Galvanized steel underride guard Sheet metal as splash guard riveted to the floor at the bottom, in the neck area above the axle of the SZM and above the axle unit Half-shell mudguards with anti-spray flaps according to EG Container locking, 4 pairs of locking cut-outs embedded in the floor for 2 x 20 foot or 1 x 40 foot containers, 4 pairs of container locking adapters, (additional cross support required at the front and rear of the container, the container must rest evenly across the width in conjunction with the locks, cross supports are not included in the scope of delivery) Caution! Damage to the Lohrblech floor by the cross supports possible! Mechanical rear extension with hand crank, can be extended by approx. 1,500 mm, can be locked every 500 mm, incl. extendable underride guard with lighting, (then no access ladder at the rear) Covered with Lohr plate in the tramline area, steel checker plate in the middle. Attention! Ramp loading via rear only possible with rear extension in retracted position! Storage space for access ramps integrated in rear extension, can only be used if rear extension is extended 1000 mm - then excess length For transporting the ramps with the rear extension retracted - Storage space for ramps in FR on the right in front of the axles 1 pair of ramps 3,000 mm long, 300 mm wide, load capacity per pair 6,000 kg, (suspension bar for ramps on rear extension) Rear sloping to approx. 500 mm Lhsdpfx Aslf Dtmscyjb Electric cable winch, 24 volt, pulling force approx. 8165 kg, mounted centrally at the front, operation with radio remote control, cable length 35 m x approx. 10 mm, with roller rope window and removable guide rollers Axles + suspension Drum brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Air suspension 1st axle automatic lift axle, including forced lowering and starting aid, actuation of 3x brakes (starting aid is functional up to an axle load excess of 30% and up to a speed of max. 25 km/h) with central lift arm Axle lift below the recomm. Driving height, therefore no warranty for tire damage Brake system 2-line compressed air brake system Colored line routing for easy service. Spring-loaded parking brake 2 swap-proof coupling heads at the front, without connecting cable EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve Vehicle stability system Wheels and tires 235/75 17.5 tires of the manufacturer's choice Steel rims in twin arrangement, factory silver Electrical system 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white LED position lights at the front 2 white/red rear lane departure lights 2 additional LED work lights at the rear, switched via reversing

Condition: used, machine/vehicle number: 9c9dadcd470a127e08914041a, empty load weight: 2,600 kg, maximum load weight: 10,800 kg, overall weight: 13,400 kg, axle configuration: 2 axles, first registration: 05/2017, tire size: 285/70 r19,5, Year of construction: 2017, Further information Fine-grained steel welded construction, fifth wheel coupling, make of our choice for 2\ kingpin, telescopic support foot, wheel chocks with holder, steel underride guard, half-shell mudguards, removable upper parts Towbar with tested 50 mm towing eye, under-coupler towbar BPW disc brake axles, air suspension with lift & lower valve, mechanical dolly steering system (required in Germany to comply with the BO circle) 2-line compressed air brake system, spring-loaded parking brake, Duomatic coupling head at the front, with connecting lines to the tractor unit, Duomatic coupling head to the trailer, incl. connecting coil, EBS, electronic brake system with EBS plug at the front, with connecting cableEBS connecting cable to the trailer, with CAN router, axle load detection for trucks via EBS, without truck instal. Ljdpfei Rivtox Acyjhb Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! 24 volt, multi-chamber lights, amber LED lighting at the side, 2 white position lights at the front, 2 white/red lane departure lights at the rear, 1 x 15-pin plug at the front, with connecting cable to the truck 1 x 15-pin socket, with connecting spiral to the semi-trailer, cable for reversing camera system with socket with Dekra approval, prepared for single-line license plate holder, contour marking with reflective strips to ECE R 048, white at the sides and red at the rear, warning sign to ECE - 70 Saddle height approx.: 960 mm

Condition: new, machine/vehicle number: 56c59c8aba35227ffb44c9f75, empty load weight: 11,350 kg, maximum load weight: 26,650 kg, overall weight: 38,000 kg, axle configuration: 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis Jumbo semi-trailer Welded steel construction with narrow cross member spacing and reinforced design, low loader external frame profile, for transporting construction machinery up to 32000 kg and up to a max. external width of the construction machinery of 2550 mm, fifth wheel plate with replaceable 2 king pins. Rear inclination to approx. 1200 mm and 7°. Ramp shaft closed at the top with steel/checker plate, In the low bed Omega rail on the side at the bottom of the outer frame as a suspension strip for tarpaulin and spacer for the lashing points, not in the wheel area. With lift table on an additional fixed lightweight outer frame with omega profile, lift table can then be raised with closed tarpaulin! 24 t. 2-speed support winch, single-side operation, with semicircular lower section and straight connecting plate, with thrust compensation, free swing radius to the rear approx. 1950 mm, Folding rear support 2 wheel chocks with holder Aluminum side bumpers Quarter-shell mudguards in front of and behind each axle With anti-spray flaps behind each axle Steel underride guard Rear spray flaps across the entire width 4 stainless steel storage box, w=800/h=350/t=350 mm, with polished door, lockable 2 x in FR-left and 2 x in FR-right in front of the 1st axle Lifting table to gooseneck, approx. 3000 mm long, can be raised hydraulically for transfer to gooseneck, with mechanical locking when raised. (inclined cylinder for good ground clearance, Fliegl standard). Operation in FR-right + additional operation with radio remote control (same as ramp operation) Lifting table can be raised with closed tarpaulin! Tarpaulin suspension in the lift table area on an additional fixed lightweight outer frame with Omega profile, lift table can be raised with closed tarpaulin! Lashing mushrooms can also be used when lowered! Lashing eyes Gooseneck: 4 pairs of 5 to lashing eyes embedded in the outer frame 2 pairs of lashing points at the top and sides of the outer frameLow bed 8 pairs of lashing mushrooms at the top and sides of the outer frame, each 10 tons 9 pairs of 5to embedded in the outer frame Axles+suspension SAF drum brake axles last axle self-steering, with automatic reversing lock via reversing light, and additional locking function on the vehicle via hand button. Air suspension with lift & lower valve + auto-reset function H & S function with quick air release 1st axle automatic lift axle, including forced lowering and starting aid, actuation of 3x brakes (starting aid is functional up to an axle load excess of 30% and up to a speed of max. 25 km/h) Axle lift below the recomm. Driving height, therefore no warranty for tire damage Wheels and tires 235 / 75 R 17,5 from leading manufacturers Twin steel rims, factory silver Lhsdpfx Acei Riw Aoyeb Brake system 2-line compressed air brake system Spring-applied parking brake 2 interchangeable clutch heads at the front, without connecting cable EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Axle load detection in the truck via EBS, without truck instal. (no calibrated scales) Electrical system 24 volt, multi-chamber lights, amber LED lighting on the side 2 white position lights at the front, in LED 2 white/red lane departure lights at the rear, 1 rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illum

Condition: new, machine/vehicle number: ebf3f771e96394cd89e56bbb7, overall weight: 11,800 kg, axle configuration: 2 axles, tire size: 235 / 75 r 17,5, Further information Chassis central axle trailer Welded fine-grained steel construction 6 pairs of lashing eyes bolted to the outside of the floor/outer frame, 5 tons each 2 pairs of lashing eyes additionally bolted to the floor, 5 tons each in the corners Gear support foot at the front Folding rear support 2 wheel chocks with holder Steel underride guard Rear spray flaps across the entire width Quarter-shell mudguards 1 plastic tool box, with shelf, w=620/h=360/t=440 mm, lockable with a padlock. (lock not included in scope of delivery) Towing device central axle trailer Towing bar with tested 40 mm towing eye Height-adjustable drawbar via spindle, max. adjustment range 300 mm Axles + suspension Drum brake axles, manufacturer's choice Axle/chassis laser-measured Reduction in tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation (rocker compensation) Wheels and tires 235 / 75 R 17,5 manufacturer's choice Factory silver steel rims Brake system 2-line compressed air brake system Hand spindle parking brake Integral air reservoir 2 non-interchangeable coupling heads at the front, with connecting cables to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin interchangeable plugs at the front, with connecting cable, Floor Ledji Rixropfx Acyehb Steel/ checker plate floor for high point load capacity Note: Slight floor corrugation possible due to welding distortion! Platform length approx. 5,200 mm Rear sloping to approx. 900 mm Front wall / front corner stanchions 25 mm aluminum hollow profile, 400 mm high, Drop sides 25 mm aluminum hollow profile, 400 mm high, foldable and removable Rear wall / rear corner stanchions 1 pair of steel stanchions attached to the frame and with bracket for locking the drive-on ramps, drive-in width approx. 2,430 mm Drive-on ramps 2 steel ramps 2,300 mm long, 510 mm wide, can be moved sidewayswith grab handle on the ramps covered with 3 toothed steel rails With gas pressure jack for one-man operation Country of registration/plates Country of registration: Germany 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white on the sides and red on the rear Paintwork Hot-dip galvanized frame incl. passivation 15-year warranty against rusting through Front wall aluminum Side wall anodized aluminium Drive-on ramps Hot-dip galvanized Attention! These are archive pictures.

Condition: used, machine/vehicle number: 4b9217583a30f28a6bc1ce196, empty load weight: 2,600 kg, maximum load weight: 10,800 kg, overall weight: 13,400 kg, axle configuration: 2 axles, first registration: 01/2014, tire size: 285/70 r19,5, Year of construction: 2013, Further information Fine-grained steel welded construction, fifth wheel coupling, make of our choice for 2\ kingpins, telescopic support foot, wheel chocks with holder, steel underride guard, half-shell mudguards Towbar with tested 50 mm towing eye, under-coupler towbar mechanically adjustable in length BPW disc brake axles, air suspension with lifting & lowering valve, electronic dolly steering system, encoder via contact in the towing eye (required in Germany to comply with the BO circle or trailer must be steered) 2-line compressed air brake system, spring-loaded parking brake, 2 non-interchangeable coupling heads at the front, with connecting lines to the tractor unit2 non-interchangeable coupling heads to the trailer EBS, electronic brake system with EBS plug at front, with connecting cable, EBS connecting cable to trailer, axle load detection for truck via EBS, without truck instal. 24 volt, multi-chamber lights, amber LED lighting at the side, 2 white position lights at the front, 2 white/red lane departure lights at the rear, 1 x 15-pin plug at the front Country of registration: Germany, with Dekra approval, prepared for single-line license plate holder, contour markings with reflective strips to ECE R 048, white at the sides and red at the rear, warning sign to ECE - 70 Ledsi Riydopfx Acyshb Saddle height approx.: 960 mm

Condition: new, machine/vehicle number: c3dd8c834afed73501f8074af, empty load weight: 3 kg, maximum load weight: 20 kg, overall weight: 24 kg, axle configuration: 3 axles, tire size: 385/55 r22,5, Further information Chassis Changing turntable Fine-grained steel welded construction Front stop, longitudinally adjustable and foldable 2 pairs of removable guide rollers, front and rear 4 container locks with sturdy outriggers on 20-basefor swap bodies 7.15 and 7.45 Turntable with strong ball bearing slewing ring 2 wheel chocks with holder Aluminum side bumper Steel underride guard Front half-shell mudguards and rear half-shell mudguards 2 stainless steel storage box, w=600/h=400/t=500 mm, with polished door, lockable 1 pair of warning signs, double LED illuminated, extendable to 3,000 mm at the rear, rear only 1 preparation plug for retrofitting warning signs at the front for customers Towing equipment Trailer turntable Drawbar with tested 40 mm towing eye Drawbar mechanically adjustable in length by 6 x 100 mm and lockable (drawbar length approx. 1,900 - 2,500 mm) Drawbar height adjustment via spring Axles + suspension BPW disc brake axles with 430 mm disc diameter Axle/chassis laser-measured Reduction of tire wear and fuel consumption Air suspension with lift & lower valve Wheels and tires 385/55 R22,5 manufacturer's choice Factory silver steel rims Brake system 2-line compressed air brake system Spring-loaded parking brake 2 interchangeable clutch heads at the front, with connecting cables to the motor vehicle, EBS, electronic brake system with EBS plug at the front, with connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red lane departure lights at the rear Removable rotating beacon Lhodpfx Asi Riylocyob 1 additional LED work light(s) at the rear, switched via reversing light 2 LED work lights on both sides (1x left, 1x right) (switched via reversing light) 1 x 15-pin plug at the front, with connecting cable, Country of registration / plates Country of registration: Germany with Dekra approval and certificate (according to §13 EG - FGV) 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white at the sides and red at the rear Paintwork Hot-dip galvanized frame incl. passivation 15-year warranty against rusting through Drawbar KTL black

Condition: new, machine/vehicle number: e763c8c2bb3370bd2342236a4, empty load weight: 3 kg, maximum load weight: 8 kg, overall weight: 11 kg, axle configuration: 2 axles, tire size: 235 / 75 r 17,5, Further information Chassis central axle tipping trailer Welded steel construction, continuous tipping shaft at the rear with 80 mm ball tipping bearing Gearbox support foot at the front 2 wheel chocks with holder Steel underride guard Lockable storage space for access ramps underneath the loading area Towing device central axle trailer Drawbar with tested 40 mm towing eye Height-adjustable drawbar via spindle, max. adjustment range 300 mm Axles + suspension Euro axles of our choice, with angular roller bearings and S-cam brake Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation (rocker compensation) Lhjdpfji Rizbjx Acyjb Wheels and tires 235 / 75 R 17,5 at the manufacturer's choice Factory silver steel rims Brake system 2-line compressed air brake systemColor-coded cable routing for easy servicing. Hand spindle parking brake Integral air reservoir without ABS, but with mechanical ALB, then max. 60 km/h approval 2 swap-proof coupling heads at the front, with connecting lines to the motor vehicle, electrics 12 volt, multi-chamber lights, without amber LED lighting at the sides, reflectors at the sides 2 white position lights at the front 2 white/red lane departure lights at the rear 1 x 7-pin 12 volt plug at the front, with connecting cable, extended by approx. 60 cm Hydraulics Three-sided tipping mechanism, hydraulic multi-piston press with lift limiter and safety cable, Low-pressure cylinder up to max. 170 bar, without throttle. If necessary, this can be retrofitted to the truck. Hydraulic connection with SVK plug NW 10/3, incl. connection hose Hydraulic actuation via truck power take-off Tilting bridges Sturdy tipper body with 4 mm sheet steel floor, steel side wall structure, continuous side walls, hinged and pivoted with central locking at the bottom. Rear corner stanchions pluggable. Rear wall can be folded down and pivoted, with central locking at the bottom. Platform length approx. 4,500 mm, side walls with 5 hinges at the bottom. Platform width 2420 mm 5 pairs of lashing eyes in the floor, 5 tons each Operating instructions The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Country of registration: Germany with Dekra approval and expert opinion, for max. 60 km/h approval, towing vehicle LoF, (max. 40 km/h possible in Switzerland) Prepared for single-line license plate holder without contour marking / reflective strips according to ECE R 048, Paintwork Hot-dip galvanized frame incl. passivation 15-year warranty against rusting through Dropside/bridge RAL 3002 carmine red Please note! If the bridge is galvanized, it will not be painted! Note! Bridge only primed inside! Wide tires also possible for an extra charge. 355 / 60 R 18, then loading height approx. 980 mm Attention: Archive pictures!

Condition: new, machine/vehicle number: 8fbda13da8c595f64678f0f82, empty load weight: 2,100 kg, maximum load weight: 11,300 kg, overall weight: 13,400 kg, axle configuration: 2 axles, tire size: 275/70 r 22,5, Further information Chassis central axle trailer Fine-grained steel welded construction Fifth wheel coupling, make of our choice for 2 kingpins. with ball bearing slewing ring, max. 20° stop Support on drawbar and dolly at the front Wheel chocks with holder Steel underride guard Half-shell mudguards Towing device central axle trailer CLG under-coupler drawbar with tested 50 mm towing eyes to the dolly and to the motor vehicle, including drawbar lock on the truck! Axles + suspension BPW disc brake axles Air suspension for Swap Train version Standard Saddle height lowered approx. 1100 mm, saddle height raised approx. 1280 mm, saddle height approx. 1140 mm, Brake system 2-line compressed air brake systemColor-coded cable routing for easy servicing. Spring-applied parking brake 2 non-interchangeable coupling heads at the front, with connecting lines to the motorized trolley, 2 non-interchangeable coupling heads with Wendelflex connecting lines to the trailer EBS, electronic brake system with EBS plug at the front, with connecting cable, EBS Wendelflex connecting lines to the trailer Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering, ECAS, via truck control, Ecas CAN 2 bus required in the truckwithout Ecas CAN 2 bus in the truck, additional operating control required in the truck (not included in the scope of delivery):Electrical system with a pre-assigned cable and a distributor box. Operation with 15-pin socket pin 11 and 15 with 2 x 7-pin socket pin 7 and 5 Note! This version must still be technically tested in conjunction with the trailer, it is likely that the dolly and the trailer can only be raised and lowered together if this is not technically possible, operation is via WABCO eTASC with hold function in lowered position + auto-reset function (no power required from the truck). Additional operation on the vehicle via WABCO eTASC + hold function in lowering position + auto-reset function (no power required from the truck) Vehicle - driving stability system Lhedpji Rizxefx Acysb ECAS only possible in conjunction with WABCO EBS. Axle load detection via EBS-Canbus signal, for indication via display in driver's cab, truck must be prepared accordingly, no truck installed (no calibrated scales) Brake release function from truck (via button) on PIN 14 and additionally via button on vehicle next to H & S valve, for releasing the brake when coupled, EBS power supply must be guaranteed! with Can Router Wheels and tires 275/70 R 22.5 tires of the manufacturer's choice Steel rims, factory silver Electrical system 24 volt, multi-chamber lights, amber LED lighting on the side Side amber LED lighting coupled with the blinker Flashing side lights 2 white LED position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable plugs at the front, with connecting cable, 2 x 7-pin non-interchangeable plugs with helical flex connection cables to the trailer Cable + plug and/or socket for reversing camera system, depending on vehicle type Operating instructions Note! Please note the currently permitted route network! Towing vehicle must be taken to the Triptis factory for approx. 1 week for adjustment of the towing bar! Please note the CLG recommendation as per the appendixThe following is required before acceptance of the order: Submission of all relevant measurements and dimensions as per the Fliegl CLG form (see appendix) The coupling height of the planned trailer must be

Condition: new, machine/vehicle number: 408ba9a39bbb8087056d6e563, overall weight: 24,000 kg, axle configuration: > 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction Turntable with powerful ball bearing slewing ring Folding rear support Lsdoi Ri Daepfx Acyshb 2 wheel chocks with holder Aluminum side bumpers Rear spray flaps across the entire width Half-shell mudguards 1st + 2nd axle with anti-spray flaps behind each axle, anti-spray flaps in front of and behind 3rd and 4th axle Excavator trough above the rear axles starting to the rear, approx. 1800 mm long, approx. 650 mm wide and approx. 150 mm deep, 2 pairs of lashing holes each 5 tons in the excavator trough on the side of the longitudinal frame approx. 300 mm from the front and approx. 200 mm in front of the rear slope 1 plastic tool box, with shelf, w=620/h=360/t=440 mm, lockable with a padlock. (lock not included in scope of delivery) 1 storage box on offset recessed in floor with lid, W=720 mm/ L=520 mm / D= 170 mm Widenings extendable to 3,000 mm (not in rear slope) (track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Wooden planks 70 mm for widening to 3,000 mm Storage compartment for wooden planks under the loading area Low loader lashing eyes (40 lashing options) 1 pair of lashing eyes on offset per 5 tons 9 pairs of lashing points at the top and sides, each 10 tons, embedded in the outer frame 2 x front on offset 7 x in the drop deck 6 pairs of lashing holes in the outer frame of the low bed, each with 5 to. (lashing strap attachment) 3 additional pairs of hinged lashing eyes, 10 tons each 1 x inside next to the main frame at the start of the low bed 1 x on offset (protrudes) 1 x embedded in the floor behind the last axle Towing equipment Trailer turntable Drawbar with tested 50 mm drawbar eye, drawbar eye inclined 8° / D-value min. 160 kN Axles + suspension Drum brake axles Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation front and rear (rocker compensation) Wheels and tires 235 / 75 R 17,5 at the manufacturer's choice Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 non-interchangeable coupling heads at the front, with connecting cables to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin interchangeable plugs at the front, with connecting cable, 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Offset at the front with steel/ checker plate flooring Then with 70 mm softwood floor, steel/ checker plate covering in the wheel housing area Rear slope with 70 mm softwood flooring Drive-on ramps Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways Covered with wood Hydraulic via tractor power take-off with throttle, actuation on the left side in FR Hydraulic connection with SVK plug NW 10/3, incl. connection hose Country of approval / plates Country of registration: Germany 24/7 service hotline Prepared for two-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white on the sides and red on the rear Warning sign according to ECE - 70 Paintwork Hot-dip galvanized frame incl. passivation 15-year warranty against rusting through Drawbar Galvanized

Condition: used, machine/vehicle number: 3ca51192c90a3f38a59d77748, empty load weight: 2,872 kg, maximum load weight: 15,128 kg, overall weight: 18,000 kg, axle configuration: 2 axles, first registration: 11/2019, tire size: 385/65 r22,5, Year of construction: 2019, Further information Welded fine-grained steel construction, front stop, longitudinally adjustable and foldable, removable pair of guide rollers, front and rear, Swap Guard - swap body guide, in front of and behind each container lock, 4 container locks with sturdy outriggers on 20-base for swap bodies 7.15 and 7.45, turntable with strong ball bearing slewing ring, wheel chocks with holder, Aluminum side collision protection, side collision protection set inwards for optimum clearance to the swap body supports, steel underride guard, underride guard shortened for optimum clearance to the swap body supports, lighting system mounted in a protected position, quarter-shell mudguards at the front and half-shell mudguards at the rear, without impact protection, spare wheel holder in basket design, plastic toolbox Drawbar (L = 2,200 mm) with tested 40 mm drawbar eye, drawbar length, drawbar height adjustment via spring SAF disc brake axles with 430 mm disc diameter, axle/chassis laser-measured Reduction in tire wear and fuel consumption, air suspension 2-line compressed air brake systemColored line routing for easy servicing, air supply 208 liters, spring-loaded parking brake, 2 swap-proof coupling heads at the front, with connecting lines to the motor vehicle, EBS, electronic brake system with EBS plug at the front, with connecting cable, )Attention: The trailer vehicle may only be towed by towing vehicles that guarantee the effectiveness of the ABS!) with lifting & lowering valve, holding function in lowering / lifting position, brake release function via button on the vehicle next to H & S valve, for releasing the brake when coupled, EBS power supply must be guaranteed! Lsdei Ri Dzjpfx Acyjhb 24 volt, multi-chamber lights, amber LED lighting at the side, 2 white position lights at the front, 2 white/red lane departure lights at the rear, 1 x 15-pin plug at the front, with connecting cable, additional LED work light(s) at the rear, switched via reversing light, LED work light at the front centered between the beams, shining to the rear, switched via reversing light Country of registration: Germany, with Dekra approval and certificate (according to §13 EG - FGV), prepared for single-line license plate holder, warning sign according to ECE - 70, ADR warning sign at the rear, hinged, contour marking with reflective strips according to ECE R 048, white at the sides and red at the rear

Condition: new, machine/vehicle number: 71cc13750cef13b72f7a55abe, empty load weight: 5,500 kg, maximum load weight: 29,500 kg, overall weight: 35,000 kg, axle configuration: 3 axles, tire size: 385/65 r22,5², Further information Chassis tipper semi-trailer Fine-grained steel welded construction, lightweight design, fifth wheel plate with interchangeable 2 kingpins Curved front end Patented 24 t. 2-speed support winch, single-side operation, with straight lower section, without thrust compensation 2 wheel chocks with holder Underride guard, folding Half-shell mudguards Integrated mudguard holder Stone-repellent surface With anti-spray flaps on last axle only 1 tarpaulin pole with bracket 2 towing hooks at the rear Ledpfoi Ri Efsx Acyohb Axles+suspension SAF disc brake axles with 430 mm disc diameter Axle/chassis laser-measured Reduction in tire wear and fuel consumption Axles in off-road version, Air suspension 1st axle automatic lift axle, including forced lowering and starting aid, actuation of 3x brakes (starting aid is functional up to an axle load excess of 30% and up to a speed of max. 25 km/h) Hot-dip galvanized lift axle mechanism 10-year warranty against rusting through Brake system 2-line compressed air brake systemColor-coded cable routing for easy servicing. Spring-loaded parking brake 2 interchangeable front clutch heads, without connecting line EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve Vehicle stability system Wheels and tires 385/65 R22.5 tires of the manufacturer's choice Steel rims, factory silver Electrical system 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable sockets at the front, without connecting cable Hydraulics Low-pressure cylinder max. 170 bar, smallest stage hard-chlorinated, with HDK screw socket, fixed part, NW 48 mm (without hose connection). Hydraulic actuation via truck power take-off Troughs Aluminum box body made of high-quality, abrasion-resistant 5 mm thick front wall, with external walls made of 30 mm hollow chamber profiles, cleanly welded, with bulk material-repellent top rail profile. Inside with access to front wall (not in conjunction with Cramaro). Shovel and brush holder on the outside of the front wall. Greenline - conical and aerodynamic trough shape Membrane rear wall Rear wall pendulum-mounted with double-joint hinge and with 2-leaf door partition 1/2 to 1/2, with pivoting gallows at the top, with one grain slider per door. Rear panel with rubber sealNote! Heat-resistant up to max. 170°C! Floor 6 mm thick throughout Standing platform with access, connection plate for air/electric and brake with large clearance for best possible operability. Roller tarpaulin on one side for depositing in FR-right, with central locking in FR-left Operating instructions For salt, lime, etc. We recommend a tipping cylinder with a hard chrome-plated piston rod so that it is not attacked by the material and rusts. The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Germany Test approval according to EC 2007/46 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips according to ECE R 048, white on the sides and red on the rear Paint finish Frame DB 7350 Novagr

Condition: new, machine/vehicle number: 207ad28f83705ed0d38a4f174, empty load weight: 3 kg, maximum load weight: 11 kg, overall weight: 14 kg, axle configuration: 2 axles, tire size: 235/75 r17,5, Further information Chassis Wechel central axle trailer Fine-grained steel welded construction Front stop, longitudinally adjustable and foldable Pair of removable guide rollers, front and rear 4 container locks with sturdy outriggers on 20-basefor swap bodies 7.15 and 7.45 flush with rear (for 7.15 swap bodies not flush with rear, forklift pockets/frame protrude) Telescopic front support leg Lodpfji Ri Iaox Acyohb 1 pair of front gear support legs, with straight lower section and single-sided operation in FR right Wheel chocks with holder Aluminum side bumpers Steel underride guard Half-shell mudguards Bracket for truck-mounted forklift at the rear, including 2 fork pockets, 2 extendable support tubes, bracket for chain safety device with pin. Underride guard with light unit can be folded away. Including 2 loose rubbers to protect the rear wall, we recommend counterweight! Partially low ground clearance with forklift, poor tracking behavior possible, without warranty! (Forklift tare weight up to max. 1500 kg for trailers). (With proximity switch for forklift control in conjunction with lift axle)The axles are shifted to the rear by the forklift bracket, observe load distribution when driving without forklift. Customer risk! (For swap body trailers, driving with a forklift is only permitted in conjunction with a swap body) Forklift bracket as AU 203670 adapted to 7.45 m swap bodies Counterweight at the front between the frames, approx. 300 kg, if necessary, exact check still required Towing device central axle trailer Tow bar with tested 50 mm towing eye, forwarding agent version (not suitable for trucks with tail lift, or exact testing still required if ordered) Lower coupler drawbar without length adjustment drawbar Axles + suspension SAF drum brake axles of the manufacturer's choice Axle/chassis laser-measured Reduction of tire wear and fuel consumption Air suspension Brake system 2-line compressed air brake systemColor-coded line routing for easy servicing. Spring-applied parking brake Duomatic connection at the front, with connection line to the engine trolley, in FR-left Duomatic connection at the front, with connection line to the motor vehicle, connection in FR-right EBS, electronic brake system with EBS plug at the front, with connecting cable, in FR-left Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve, holding function in each case in lowering / lifting position Vehicle - driving stability system Wheels and tires 235/75 R17.5 tires of the manufacturer's choice Steel rims in twin arrangement, factory silver Electrical system 24 volt, 4 x 3 chamber lights + 1 round reversing light and + 1 round rear fog light, amber LED lighting on the side, lights mounted in a protected position! 2 white position lights at the front 2 white/red rear lane departure lights 1 x 15-pin plug at the front, with connecting cable, in FR-left 2 x 7-pin sockets in FR left rear for truck-mounted forklift 1 x 15-pin socket in FR left rear for truck-mounted forklift LED work lights on both sides behind the 2nd axle (switched via reversing light) Additional LED work light(s) at the rear, switched via reversing light Approval / plates Germany with Dekra approval and certificate (according to §13 EG - FGV) 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white at the sides and red at the rear Paint finish Frame

Condition: new, machine/vehicle number: 83732a53562459145277be051, empty load weight: 4,200 kg, maximum load weight: 27,800 kg, overall weight: 32,000 kg, axle configuration: 2 axles, tire size: 385/65 r22.5, Further information Chassis tipper semi-trailer Fine-grained steel welded construction, lightweight design, fifth wheel plate with interchangeable 2 kingpins Curved front end Patented 24 t. 2-speed support winch, single-side operation, with straight lower section, without thrust compensation 2 wheel chocks with holder Underride guard, folding Half-shell mudguards Integrated mudguard holder Stone-repellent surface With anti-spray flaps on last axle only 1 tarpaulin pole with bracket 2 towing hooks at the rear Axles+suspension SAF disc brake axles with 430 mm disc diameter Axle/chassis laser-measured Reduction in tire wear and fuel consumption Axles in off-road version, Air suspension 1st axle automatic lift axle, including forced lowering and starting aid, actuation of 3x brakes (starting aid is functional up to an axle load excess of 30% and up to a speed of max. 25 km/h) Hot-dip galvanized lift axle mechanism 10-year warranty against rusting through Brake system 2-line compressed air brake systemColor-coded cable routing for easy servicing. Spring-loaded parking brake 2 interchangeable front clutch heads, without connecting line EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve Vehicle stability system Automatic tilt lowering with shut-off valve Wheels and tires 385/65 R22.5 tires of the manufacturer's choice Steel rims, factory silver Electrical system 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable sockets at the front, without connecting cable Hydraulics Low-pressure cylinder max. 170 bar, smallest stage hard-chlorinated, with HDK screw socket, fixed part, NW 48 mm (without hose connection). Hydraulic actuation via truck power take-off Troughs Aluminum box body made of high-quality, abrasion-resistant 5 mm thick front wall, with external walls made of 30 mm hollow chamber profiles, cleanly welded, with bulk material-repellent top rail profile. Inside with access to front wall (not in conjunction with Cramaro). Shovel and brush holder on the outside of the front wall. Greenline - conical and aerodynamic trough shape Membrane rear wall Rear wall as swing flap with double-jointed hinge, resting on the outside with double hook lock. Lsdsi Ri Nbopfx Acyshb Rear panel with rubber sealNote! Heat-resistant up to max. 170°C! Floor 6 mm thick throughout Standing platform with access, connection plate for air/electric and brake with large clearance for best possible operability. Roller tarpaulin on one side for depositing in FR-right, with central locking in FR-left Operating instructions For salt, lime, etc. We recommend a tipping cylinder with a hard chrome-plated piston rod so that it is not attacked by the material and rusts. The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Germany Test approval according to EC 2007/46 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips according to ECE R 048, white on the sides and red on the rear Paint finish Frame DB 7350 nova gray 10 J

Condition: new, machine/vehicle number: 8b1f4087611d72661dc0b3869, empty load weight: 4,500 kg, maximum load weight: 27,500 kg, overall weight: 32,000 kg, axle configuration: 2 axles, tire size: 385/65 r22.5, Further information Chassis tipper semi-trailer Fine-grained steel welded construction, in basic lightweight design, fifth wheel plate with interchangeable 2 kingpins Curved front end Patented 24 t. 2-speed support winch, single-side operation, with straight lower section, without thrust compensation Wheel chocks with holder Underride guard, folding Half-shell mudguards Tarpaulin pole with bracket Tow hook at the rear Axles+suspension SAF disc brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Axles in off-road version, Air suspension 1st axle automatic lift axle, including forced lowering and starting aid, actuation of 3x brakes (starting aid is functional up to an axle load excess of 30% and up to a speed of max. 25 km/h) Lhsdpfei Ri Nfox Acysb Hot-dip galvanized lift axle mechanism 10-year warranty against rusting through Brake system 2-line compressed air brake systemColor-coded cable routing for easy servicing. Spring-loaded parking brake 2 interchangeable front clutch heads, without connecting line EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve Vehicle stability system Wheels and tires 385/65 R22.5 Steel rims, factory silver Electrical system 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable sockets at the front, without connecting cable Hydraulics Low-pressure cylinder max. 170 bar, smallest stage hard-chlorinated, with HDK screw socket, fixed part, NW 48 mm (without hose connection). Hydraulic actuation via truck power take-off Troughs Round steel body in Stone Master design made of highly wear-resistant HB 400/450 steel. Sloping front wall with external hydraulic en with access to front wall. Greenline - conical and aerodynamic body shape Bucket and brush holder on the outside of the front wall. Membrane rear wall Rear wall as swing flap with double-jointed hinge, resting on the outside with double hook lock. 2 clamping screws with toggle fasteners at the bottom side. Side walls 4 mm thick throughout, base 4/5 mm thick, wear and weight-optimized design, Standing platform with step, connection plate for air/electric and brake with large clearance for optimum operability. Roller tarpaulin on one side for depositing in FR-right, with central locking in FR-left Operating instructions For salt, lime, etc. We recommend a tipping cylinder with a hard chrome-plated piston rod so that it is not attacked by the material and rusts. The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Germany Test approval according to EC 2007/46 Body strength according to EN 12642 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips according to ECE R 048, white at the sides and red at the rear Paint finish Frame DB 7350 nova gray10-year warranty against rusting through Support legs coated black Body RAL 7035 light gray Fliegl StoneMaster advertising on the sides and rear Roll-up tarpaulin RAL on request, single color Available thermally insulated version: Cover BA

Condition: new, machine/vehicle number: 06017a31026c05fc8f6ccf5ae, empty load weight: 3,055 kg, maximum load weight: 14,945 kg, overall weight: 18,000 kg, axle configuration: 2 axles, tire size: 235/75 r17,5, Further information Chassis Changing turntable Fine-grained steel welded construction Front stop, longitudinally adjustable and foldable Pair of removable guide rollers, front and rear 4 container locks with sturdy outriggers on 20-basefor swap bodies 7.15 and 7.45 Turntable with sturdy ball bearing slewing ring 2 wheel chocks with holder Aluminum side bumper Steel underride guard Quarter-shell mudguards at the front and half-shell mudguards at the rear Towing equipment Trailer turntable Drawbar with tested 40 mm drawbar eye Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Air suspension Brake system 2-line compressed air brake systemColor-coded line routing for easy servicing. Ledpfxoi Ri Rcs Acyohb Spring-loaded parking brake 2 non-interchangeable coupling heads at the front, with connecting lines to the motor vehicle, EBS, electronic braking system with EBS plug at the front, with connecting cable, Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve, holding function in both lowering and lifting position Wheels and tires 235/75 R17.5 tires of the manufacturer's choice Steel rims in twin arrangement, factory silver Electrical system 24 volt, multi-chamber lights in LED with resistor, amber LED lighting at the side, license plate lighting in LED, (Note! with certain towing vehicles, misdiagnosis may occur although the function is given) 2 white front position lights in LED 2 white/red rear lane departure lights in LED 1 x 15-pin plug at the front, with connecting cable, Additional LED work light(s) at the rear, switched via reversing light Approval / plates Germany with Dekra approval and certificate (according to §13 EG - FGV) 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white at the sides and red at the rear Paint finish Frame DB 7350 nova gray Attention: Archive pictures!