Used Fliegl Twp Trailers for sale (340)

Condition: new, functionality: fully functional, machine/vehicle number: WFDFLT21801012090, empty load weight: 2,800 kg, maximum load weight: 15,200 kg, overall weight: 18,000 kg, axle configuration: 2 axles, total length: 9,300 mm, total width: 2,550 mm, total height: 1,300 mm, suspension: air, tire size: 385/55 R22,5", tire condition: 100 %, color: silver, Customized Transport Solution Configure your Fliegl vehicle according to your individual requirements. The vehicle shown is an example configuration. Production and equipment are tailored to customer specifications. ### Chassis – Turntable Drawbar Trailer for Roll-Off Containers * High-tensile steel welded chassis construction * Sliding frame system: * The container is loaded from the rear onto the sliding frame and pushed forward * Front container stop adjustable for 6.0 m, 6.5 m and 7.0 m roll-off containers with external rollers * Container locking system: * 2 pairs of recessed locking hooks integrated into the floor * Pneumatic operation * Internal 2-point locking system * Not suitable for roll-off containers with internal centre beam * Designed for the transport of roll-off containers with subframe according to DIN 30722 * Heavy-duty turntable with ball-bearing slewing ring * 2 wheel chocks with holders * Aluminium side underrun protection * Steel rear underrun protection * Semi-circular mudguards * Rear impact protection, mounted vertically on left and right side, with delta rubber buffers on underrun protection brackets * Spare wheel carrier for 1 spare wheel, including wheel mounting kit * Plastic toolbox with drawer and shelf insert, dimensions: 650 x 520 x 670 mm (W x H x D), lockable with padlock ### Drawbar * Drawbar with certified 40 mm towing eye ### Axles & Suspension * SAF disc brake axles * Laser wheel alignment of axles and suspension for reduced tyre wear and lower fuel consumption * Air suspension with raise-and-lower valve ### Wheels & Tyres * 385/55 R 22.5 tyres * Manufacturer's choice * Steel rims, factory silver finish Bjdpfozggicjx Aarsli ### Braking System * Dual-line compressed air braking system * Spring-loaded parking brake * Drive-away protection: opening the container locking system automatically activates the spring-loaded parking brake * Vehicle Stability Control System * Two non-interchangeable coupling heads at the front with connecting lines to the towing vehicle * EBS (Electronic Braking System) with front EBS connector and connecting cable Note: The trailer may only be operated with towing vehicles that ensure proper ABS functionality. ### Electrical System * 24 V electrical system * Multi-chamber rear lights * Yellow LED side marker lights * 2 white front position lights * 2 white/red rear outline marker lights * 2 additional LED work lights at the rear, activated via reverse gear * 2 x 7-pin non-interchangeable front plugs with connecting cable ### Registration & Compliance * Registration country: Germany * DEKRA inspection and certification included (according to §13 EC-FGV) * 24/7 service hotline * Prepared for single-line licence plate holder * Reflective contour markings according to ECE R048 (white on the sides, red at the rear) ### Paint Finish * Chassis: hot-dip galvanised or painted according to customer requirements * Drawbar: black KTL coating (cathodic dip coating) --- Customized Transport Solution Configure your Fliegl vehicle according to your individual requirements. The vehicle shown is an example configuration. Production and equipment are tailored to customer specifications.

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 2,800 kg, maximum load weight: 15,200 kg, overall weight: 18,000 kg, axle configuration: 2 axles, total length: 9,300 mm, total width: 2,550 mm, total height: 1,300 mm, suspension: air, tire size: 385/55 R22,5", tire condition: 100 %, Customized Transport Solution Configure your Fliegl vehicle according to your individual requirements. The vehicle shown is an example configuration. Production and equipment are tailored to customer specifications. ### Chassis – Turntable Drawbar Trailer for Roll-Off Containers * High-tensile steel welded chassis construction * Sliding frame system: * The container is loaded from the rear onto the sliding frame and pushed forward * Front container stop adjustable for 6.0 m, 6.5 m and 7.0 m roll-off containers with external rollers * Container locking system: * 2 pairs of recessed locking hooks integrated into the floor * Pneumatic operation * Internal 2-point locking system * Not suitable for roll-off containers with internal centre beam * Designed for the transport of roll-off containers with subframe according to DIN 30722 * Heavy-duty turntable with ball-bearing slewing ring * 2 wheel chocks with holders * Aluminium side underrun protection * Steel rear underrun protection * Semi-circular mudguards * Rear impact protection, mounted vertically on left and right side, with delta rubber buffers on underrun protection brackets * Spare wheel carrier for 1 spare wheel, including wheel mounting kit * Plastic toolbox with drawer and shelf insert, dimensions: 650 x 520 x 670 mm (W x H x D), lockable with padlock ### Drawbar * Drawbar with certified 40 mm towing eye ### Axles & Suspension * SAF disc brake axles * Laser wheel alignment of axles and suspension for reduced tyre wear and lower fuel consumption * Air suspension with raise-and-lower valve ### Wheels & Tyres * 385/55 R 22.5 tyres * Manufacturer's choice * Steel rims, factory silver finish ### Braking System * Dual-line compressed air braking system * Spring-loaded parking brake * Drive-away protection: opening the container locking system automatically activates the spring-loaded parking brake * Vehicle Stability Control System * Two non-interchangeable coupling heads at the front with connecting lines to the towing vehicle * EBS (Electronic Braking System) with front EBS connector and connecting cable Note: The trailer may only be operated with towing vehicles that ensure proper ABS functionality. ### Electrical System * 24 V electrical system * Multi-chamber rear lights * Yellow LED side marker lights * 2 white front position lights * 2 white/red rear outline marker lights * 2 additional LED work lights at the rear, activated via reverse gear * 2 x 7-pin non-interchangeable front plugs with connecting cable ### Registration & Compliance Bledpfx Aozggghjaroi * Registration country: Germany * DEKRA inspection and certification included (according to §13 EC-FGV) * 24/7 service hotline * Prepared for single-line licence plate holder * Reflective contour markings according to ECE R048 (white on the sides, red at the rear) ### Paint Finish * Chassis: hot-dip galvanised or painted according to customer requirements * Drawbar: black KTL coating (cathodic dip coating) Customized Transport Solution Configure your Fliegl vehicle according to your individual requirements. The vehicle shown is an example configuration. Production and equipment are tailored to customer specifications.

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 15,600 kg, maximum load weight: 8,400 kg, overall weight: 24,000 kg, axle configuration: 3 axles, loading space width: 2,520 mm, loading space height: 860 mm, total length: 10,900 mm, total width: 2,550 mm, suspension: air, tire size: 235 / 75 r 17,5, tire condition: 100 %, Additional Information Chassis Steel welded construction 1 pair of wheel recesses embedded in the steel platform in the wheel arch area, angled for access, length at the bottom approx. 1400 mm, approx. 400 mm deep. Frame in the main beam area is 400 mm higher than the wheel recess. If machines are to be transported where the overall height needs to be checked, please provide the technical data sheet of the machine types with precise details (if the overall height is exceeded -> customer's risk, approval required). Depending on the ground clearance under the machines, inserts in the wheel recesses may be required by the customer. Turntable with robust ball bearing race, storage box embedded in the turntable extension. Foldable rear support. 2 chock blocks with holder. Aluminum side impact protection. Splash guards at the rear, covering the entire width. Extendable widening elements to 3,000 mm (not in the rear slope). (However, the track width of the construction machines or vehicles to be transported must not exceed the outer frame width of 2,550 mm.) Storage compartment for wooden planks in the center of the loading area. Wooden planks 70 mm for widening to 3000 mm. Tie-down eyes, low loader 110 3 pairs of tie-down points, each with 10 tons capacity, integrated in the floor at the front. Includes 6 pairs of tie-down rings embedded on top and on the side in the outer frame, each with 10 tons capacity. 1 x in the neck area. The remaining ones are distributed in between, with a distance of no more than 1200 mm. 1 x rear slope. 5 pairs of pocket slots embedded in the outer frame, inside 70 x 40 mm, (can be converted to 5 tons ring tie-down eyes, not included in the scope of delivery). Coupling device, trailer turntable. Drawbar with tested 40 mm drawbar eye. Axles + Suspension SAF drum brake axles. Axle/chassis laser-aligned, reducing tire wear and fuel consumption. Parabolic suspension with maintenance-free steel-rubber bearing. Braking system 2-line compressed air braking system. Color-coded line routing for easy servicing. Spring-loaded parking brake. 2 fail-safe coupling heads at the front, with connection lines to the towing vehicle. ABS and ALB, with ABS plug at the front, with connection cable. Note: The trailer may only be towed by towing vehicles that ensure the effectiveness of the ABS! Wheels & Tires 235/75R17.5, according to manufacturer's choice. Steel rims in twin configuration, factory silver. Electrical system 24 Volt, multi-chamber lights, yellow LED lighting on the sides. 2 white position lights at the front. 2 white/red side marker lights at the rear. 2 x 7-pole fail-safe plugs at the front, with connection cable. Blsdpfxsi Ri Rye Aarji 1 LED rotating beacon with holder, switched via the sidelights (beacon can be removed). 2 pairs of warning panels, double LED-illuminated and extendable to 3,000 mm. Floor Front area, steel floor, included. Thereafter with 70 mm soft wood floor, in the wheel arch area steel/diamond plate covering. Rear slope with 70 mm soft wood floor. Low loader platform including rear slope 8,200 mm. Ramps Steel ramps 2,800 mm long, 750 mm wide, laterally movable. Covered with wood. With spring-assisted support. Operating instructions At 10,000 kg axle load, an exception permit is required, only indivisible load is possible!!! The specified total weight is technically possible, depending on the load, the total weight may not be reached while observing the permissible axle/support and saddle loads. Country of registration/sign

Condition: new, machine/vehicle number: Produktpalette, empty load weight: 8,400 kg, maximum load weight: 15,600 kg, overall weight: 24,000 kg, axle configuration: 3 axles, loading space width: 2,520 mm, loading space height: 860 mm, total length: 10,900 mm, total width: 2,550 mm, suspension: air, tire size: 235 / 75 r 17,5, tire condition: 100 %, Custom-tailored transport solution Configure your Fliegl vehicle according to your requirements. The vehicle shown is an example. Production and equipment are tailored to individual customer needs. Further information Chassis Steel welded construction Turntable with robust ball bearing race Foldable rear support 2 wheel chocks + holder Aluminum side impact protection Splash guards at the rear over the entire width Quarter panel fenders in front of the 1st axle 1 pair of wheel recesses embedded in the low-bed area in front of the 1st axle, angled for entry, approximately 1600 mm long at the bottom, approximately 400 mm deep. Note: Frame in the main beam area is 400 mm higher than the wheel recess. 2 pairs of wheel recesses embedded in the low-bed area between the axles, angled for entry, approximately 600 mm long at the bottom, approximately 300 mm deep. Note: Frame in the main beam area is 300 mm higher than the wheel recess. Bjdji Ri Rvopfx Aarsli Extensible widening to 3,000 mm (not in the rear slope) Wooden planks 70 mm for widening to 3000 mm Tie-down eyes, low-bed trailer 1 pair of tie-down cutouts embedded in the longitudinal beam at the front in front of the 1st axle, each 10 tons. 4 pairs of tie-down holes in the outer frame, each 5 tons. 7 pairs of tie-down eyes embedded on the top and side in the outer frame, each 10 tons. 1 x at the front in front of the 1st axle 6 x in the low-bed First tie-down eye 250 mm from the front and last max. 250 mm from the rear, distance between tie-down eyes not greater than 1100 mm Coupling device, trailer turntable Tow hitch with tested 40 mm tow ball Axles + Suspension SAF drum brake axles Axle/chassis laser-aligned, reducing tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearing Wheels and tires 235/75R17.5, according to manufacturer's choice Steel rims in twin configuration, factory silver Braking system 2-line compressed air braking system Spring-loaded parking brake 2 non-interchangeable coupling heads at the front, with connecting lines to the towing vehicle, ABS and ALB, with ABS connector at the front, with connecting cable. Note: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrical system 24 Volt, multi-chamber lights, yellow LED lighting on the sides, 2 white position lights at the front 2 white/red marker lights at the rear 2 x 7-pole non-interchangeable plugs at the front, with connecting cable 1 LED rotating beacon with holder, switched via parking lights (beacon can be removed) 2 pairs of warning signs, double LED-illuminated and extensible to 3,000 mm Floor Front slope with steel/diamond plate covering Storage box embedded in the drive-over slope to the front slope, then with 70 mm soft wood floor, in the wheel arch area steel/diamond plate covering Rear slope with 70 mm soft wood floor Low-bed platform including rear slope 6500 mm Ramps Steel ramps 2,800 mm long, 750 mm wide, laterally adjustable Covered with wood With spring-assisted support Operating instructions With an axle load of 10,000 kg, an exemption permit is required, only indivisible loads are possible!!! The specified total weight is technically possible, depending on the load, the total weight may not be reached while complying with the permissible axle/support and saddle loads. (Poor driving and handling behavior may occur due to incorrect load distribution) Registration country/Signs Registration country: Germany With DEKRA acceptance and certi

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 6 kg, maximum load weight: 12 kg, overall weight: 18 kg, axle configuration: 2 axles, loading space width: 2,520 mm, loading space height: 900 mm, total length: 10,730 mm, total width: 2,550 mm, suspension: air, tire size: 235 / 75 r 17,5, tire condition: 100 %, Additional Information Chassis, Low-Bed Trailer Steel welded construction Turntable with robust ball bearing, storage box integrated into the turntable extension Bjdpji Ri N Hjfx Aarsli Foldable rear support Chocks with holder Aluminum side impact protection Half-shell fenders on the 1st axle, quarter-shell fenders in front of and behind the 2nd axle with anti-splash flaps behind each axle 1 plastic toolbox, with insert, w=620/h=360/d=440 mm, lockable with padlock. (Lock not included) Extensions extendable to 3,000 mm (not in rear slope) (The track width of the construction machines or vehicles to be transported must not exceed the outer frame width of 2,550 mm), storage compartment for wooden planks in the center of the loading area, wooden planks 70 mm for extension to 3000 mm Tie-down points, low-bed trailer 3 pairs of tie-down points, each 10 tons, integrated into the front of the floor 6 pairs of tie-down eyes, each 10 tons, embedded in the top and side of the outer frame 1 x in the neck area, the rest distributed in between, with a distance of no more than 1200 mm 1 x rear slope 5 pairs of ring tie-down points embedded in the outer frame, each 5 tons (instead of stringer pockets) Coupling device, trailer turntable Drawbar with tested 40 mm towing eye Axles + Suspension SAF drum brake axles Axle/chassis laser-aligned to reduce tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearing Wheels and Tires 235/75R17.5 as chosen by the manufacturer Steel rims in twin arrangement, factory silver Braking System 2-line pneumatic brake system Spring-loaded parking brake 2 non-interchangeable coupling heads at the front, with connecting lines to the tractor, ABS and ALB, with ABS plug at the front, with connection cable Note: The trailer may only be pulled by towing vehicles that ensure the effectiveness of the ABS! Electrical System 24 Volt, multi-chamber lights, yellow LED lighting on the sides 2 white/red position lights at the rear 2 white position lights at the front 1 rotating beacon with holder, switched on via parking lights (beacon can be removed) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm 2 x 7-pin non-interchangeable plugs at the front, with connection cable Floor Front area steel floor then with 70 mm softwood floor, in the wheel arch area steel/diamond plate Rear slope with 70 mm softwood floor Low-bed area including rear slope 8,200 mm Ramps Steel ramps 2800 mm long, 750 mm wide, laterally adjustable additional ramp securing device foldable at the bottom (to prevent the ramps from sliding sideways, not in conjunction with hydraulically adjustable ramps) covered with wood with spring-loaded support Operating instructions For a 10,000 kg axle load, a special permit is required. The permit must be applied for separately in each federal state; the legislator does not have to guarantee approval for 20 tons GVM. Customer risk. The specified total weight is technically possible, depending on the cargo, the total weight may not be reached while complying with the permissible axle/support and saddle loads. Approval / Signage Country of approval: Germany Type approval according to EC 2007/46 24/7 service hotline prepared for license plate holder, two lines Contour marking with reflective tape according to ECE R 048, white on the sides and red at the rear Warning sign according to ECE - 70 Paint Frame, DB Novagrau (DB Novagrau is a color) Ramps, hot-dip galvanized Note: Archive images!

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 5,000 kg, maximum load weight: 13,000 kg, overall weight: 18,000 kg, axle configuration: 2 axles, loading space width: 2,520 mm, loading space height: 380 mm, total length: 12,000 mm, total width: 2,550 mm, tire size: 235 / 75 r 17,5, tire condition: 100 %, Customized Transport Solution Configure your Fliegl vehicle according to your requirements. The vehicle shown is an example. Production and equipment are tailored to individual customer needs. Further Information Chassis Steel welded construction Turntable with robust ball bearing race, storage box recessed in the turntable extension Foldable rear support Chocks with holder Aluminum side impact protection Splash guard at the rear over the entire width Quarter panel fenders in front of the 1st axle Spare wheel holder for 1 spare wheel, with wheel fastening kit Spare wheel, same brand as the standard tires, steel rim Plastic toolbox, with insert, w=620/h=360/d=440 mm, lockable with a padlock. (Lock not included) Tie-down points for low-loader 3 pairs of tie-down points, 10 tons each, integrated in the floor at the front 6 pairs of tie-down eyes recessed in the upper and side parts of the outer frame, 10 tons each 1 x at the neck area, the rest spaced out with a maximum distance of 1200 mm 1 x rear slope 5 pairs of ring tie-down points recessed in the outer frame, 5 tons each (can be converted to stake pockets) Coupling device, trailer, turntable Drawbar with tested 40 mm drawbar eye Axles and Suspension SAF drum brake axles Axle/chassis laser-aligned, reducing tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber mounting Wheels and Tires 235 / 75 R 17,5 According to the manufacturer's choice Steel rims in twin arrangement, factory silver Braking System 2-line compressed air braking system Spring brake parking brake 2 fail-safe coupling heads at the front, with connecting lines to the towing vehicle ABS and ALB, with ABS plug at the front, with connecting cable Voltage converter for 12/24 Volt operation Note! A 7-pin socket, 12 Volt, is required on the tractor/tow vehicle! (Required in conjunction with the voltage converter for electrical system!) Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrical System 24 Volt, multi-chamber lights, yellow LED lighting on the sides 2 white/red position lights at the rear 2 white position lights at the front Additional LED work lights at the rear, switched on via reversing light 2 x 7-pin fail-safe plugs at the front, with connecting cable 1 x 7-pin agricultural plug Voltage converter 12/24 Volt (only for electrical system, not for ABS/EBS) Floor Front area: steel floor Then with 70 mm softwood floor, steel/non-slip sheet metal covering in the wheel arch area Rear slope with 70 mm softwood floor Blodpfoi Ri Nxjx Aarji Low-loader platform including rear slope 8,200 mm Loading Ramps Steel ramps 2,800 mm long, 750 mm wide, laterally movable Covered with wood With spring-assisted support Operating Instructions A special permit is required for an axle load of 10,000 kg. The permit must be applied for separately in each federal state; a guarantee for a 20-ton gross vehicle weight must not be given by the legislator. Customer risk. Country of Registration / Signs Country of registration: Germany With DEKRA inspection and certificate (according to §13 EG - FGV) 24/7 Service Hotline Prepared for license plate holder, two-line Contour marking with reflective tape according to ECE R 048, white on the sides and red at the rear Paintwork Frame DB 7350 Novagrau 10-year warranty against rust Drawbar galvanized or black, according to manufacturer's choice Loading ramps hot-dip galvanized Note: Archive images!

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 14,300 kg, maximum load weight: 9,700 kg, overall weight: 24,000 kg, axle configuration: 3 axles, loading space width: 2,520 mm, loading space height: 900 mm, total length: 12,000 mm, total width: 2,550 mm, suspension: air, tire size: 235 / 75 r 17,5, tire condition: 100 %, Customized Transport Solution Configure your Fliegl vehicle to meet your requirements. The vehicle shown is an example. Production and equipment are customized according to customer specifications. Further Information Chassis Steel welded construction Turntable with robust ball bearing Foldable rear support 2 wheel chocks + holder Blodpfxji Ri I No Aarji Aluminum side underrun protection Splash guards at the rear over the entire width Quarter panel fenders in front of the 1st axle Excavator arm recess starting above the rear axles to the rear, approx. 1800 mm long, approx. 650 mm wide and approx. 150 mm deep, 2 pairs of lashing points of 5 tons each in the excavator arm recess on the side of the longitudinal frame, approx. 300 mm from the front and approx. 200 mm in front of the rear slope 1 storage box recessed in the gooseneck in the floor with a lid, W=720 mm/ L=520 mm / D= 170 mm 1st pair of wheel recesses recessed in the gooseneck in the low-loader wheel well area, sloped for access, length at the bottom approx. 1600 mm, approx. 400 mm deep. Note! Frame in the main beam area is 400 mm higher than the wheel recess. 2nd pair of wheel recesses between the axles recessed in the low-loader in the wheel well area, sloped for access, length at the bottom approx. 600, approx. 300 mm deep. Note! Frame in the main beam area is 300 mm higher than the wheel recess. Wheel recess cover pull-out from the main frame, with wood inserts. Distance from the outer frame, beam to beam, approx. 1280 mm Extensions pull-out to 3,000 mm, foldable at the wheel recess extensions (extension not in the rear slope and not in the wheel recesses at the bottom) Storage compartment for wooden planks in the middle of the loading area or under the loading area, depending on technical feasibility Wooden planks 70 mm for extension to 3000 mm Lashing points, low-loader 1 pair of ring lashing points recessed at the front on the gooseneck, each 5 tons 8 pairs of lashing eyes at the top and on the side recessed in the outer frame, each 10 tons 2 x at the front on the gooseneck 6 x in the low-loader, the first lashing point 250 mm from the front and the last one max. 250 mm from the rear, the distance between the lashing points is no more than 1100 mm 5 pairs of ring lashing points recessed in the outer frame, each 5 tons (can be converted to stake pockets) Coupling system, trailer, turntable Drawbar with tested 50 mm drawbar eye with 8° inclined drawbar eye Axles + Suspension SAF drum brake axles Axle/chassis laser-aligned, reducing tire wear and fuel consumption Air suspension with lifting and lowering valve, can be operated separately at the front and rear Wheels and tires 235/75R17.5 according to manufacturer's choice Steel rims in twin arrangement, factory silver Braking system 2-line compressed air brake system Spring-loaded parking brake Trailer Info Center for displaying vehicle data such as axle load (no calibrated scale) and odometer Axle load detection via EBS-CAN bus signal, for display on the display in the cab, truck must be suitably prepared, no truck installation (no calibrated scale) Vehicle-driving stability system Duomatic connection at the front, with connecting cable to the towing vehicle EBS, Electronic Braking System with EBS plug at the front, with connecting cable Note: The trailer may only be towed by towing vehicles that ensure the effectiveness of the ABS! Electrical system 24 Volt, multi-chamber lights in LED with resistor, yellow LED lighting on the side, license plat

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, overall weight: 24,000 kg, axle configuration: > 3 axles, loading space height: 900 mm, total length: 11,940 mm, total width: 2,550 mm, suspension: air, tire size: 235 / 75 r 17,5, tire condition: 100 %, Additional Information Low-bed semi-trailer chassis Steel welded construction Turntable with heavy-duty ball bearing ring Folding rear outriggers 2 support wedges with holder Aluminum side impact protection Rear splash guards covering the entire width Semi-fender for 1st and 2nd axles with anti-spray splash guards behind each axle, anti-spray splash guards in front of and behind the 3rd and 4th axles Excavator arm recess above the rear axles, extending to the rear, approximately 1800 mm long, approximately 650 mm wide and approximately 150 mm deep, 2 pairs of lashing points of 5 tons each in the excavator arm recess, laterally on the longitudinal frame, approximately 300 mm from the front and approximately 200 mm in front of the rear slope 1 plastic toolbox, with insert, w=620/h=360/d=440 mm, lockable with a padlock (lock not included) 1 storage box recessed in the gooseneck at the bottom with lid, W=720 mm/ L=520 mm / D= 170 mm Extendable widening elements to 3,000 mm (not in the rear slope) (However, the track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Wooden planks 70 mm for widening to 3000 mm Storage compartment for wooden planks under the loading platform Lashing eyes for low-bed trailer (40 lashing options) 1 pair of lashing eyes on the gooseneck, each 5 tons 9 pairs of lashing eyes embedded above and on the side in the outer frame, each 10 tons 2 x at the front on the gooseneck 7 x in the low bed 6 pairs of lashing eyes in the outer frame from the low bed, each 5 tons (for attaching tie-down straps) 3 pairs of folding lashing eyes additionally, each 10 tons 1 x inside next to the main frame at the beginning of the low bed 1 x on the gooseneck (protruding) 1 x behind the last axle, recessed in the floor Coupling device for the trailer turntable Drawbar with tested 50 mm drawbar eye, drawbar eye inclined by 8° / D-value min. 160 kN Bsdpfx Aji Ri Daearjli Axles + Suspension Drum brake axles Parabolic spring suspension with maintenance-free steel-rubber bearing and mechanical axle load equalization at the front and rear (rocker equalization) Wheels and Tires 235 / 75 R 17.5 according to the manufacturer's choice Steel rims in twin arrangement, factory silver Braking System 2-line compressed air braking system Spring-loaded parking brake 2 fail-safe coupling heads at the front, with connecting lines to the towing vehicle, ABS and ALB, with ABS connector at the front, with connecting cable Electrical System 24 Volt, multi-chamber lights, yellow LED lighting on the sides 2 white position lights at the front 2 white/red side marker lights at the rear 2 x 7-pole fail-safe plugs at the front, with connecting cable, 1 LED rotating beacon with holder, switched via parking lights (beacon removable) 2 pairs of warning signs double LED illuminated and extendable to 3,000 mm Floor Gooseneck at the front with steel / checkered plate covering followed by 70 mm softwood floor, wheel arch area with steel / checkered plate covering Rear slope with 70 mm softwood floor Ramps Steel ramps 2,800 mm long, 750 mm wide, laterally adjustable covered with wood Hydraulically operated via towing vehicle auxiliary drive with throttle, operation on the left-hand side at the front Hydraulic connection with SVK plug NW 10/3, incl. connecting hose Country of Registration / Signs Country of Registration: Germany 24/7 Service Hotline prepared for two-line license plate holder Contour marking with reflective strips ac

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 8,500 kg, maximum load weight: 15,500 kg, overall weight: 24,000 kg, axle configuration: > 3 axles, loading space width: 2,520 mm, loading space height: 890 mm, total length: 11,940 mm, total width: 2,550 mm, suspension: air, tire size: 235 / 75 r 17,5, tire condition: 100 %, Custom-Tailored Transport Solution Configure your Fliegl vehicle according to your requirements. The vehicle shown is an example. Production and equipment are customized according to customer specifications. More Information Chassis Steel welded construction Turntable with heavy-duty ball bearing Foldable rear support 2 outrigger plates with holder Aluminum side impact protection Splash guards at the rear, covering the entire width Semi-elliptical fenders for 1st and 2nd axles with anti-spray splash guards behind each axle, anti-spray splash guards in front of and behind the 3rd and 4th axles Excavator arm recess starting above the rear axles and extending to the rear, approx. 1800 mm long, approx. 650 mm wide and approx. 150 mm deep, 2 pairs of lashing points, each 5 tons, in the excavator arm recess on the side of the longitudinal frame, approx. 300 mm from the front and approx. 200 mm in front of the rear slope. 1 plastic toolbox with insert, w=620/h=360/d=440 mm, lockable with a padlock (lock not included). 1 storage box recessed into the gooseneck with a cover, W=720 mm / L=520 mm / D=170 mm Extendable widening sections to 3,000 mm Wooden planks, 70 mm, for widening to 3,000 mm Storage compartment for wooden planks under the loading area Lashing points for low-bed trailers (40 lashing options) 1 pair of lashing points on the gooseneck, each 5 tons 9 pairs of lashing eyes recessed on the top and side of the outer frame, each 10 tons 2 x at the front on the gooseneck 7 x in the low bed 6 pairs of lashing points in the outer frame of the low bed, each 5 tons (tie-down strap attachment) 3 pairs of folding lashing points, each 10 tons 1 x inside next to the main frame at the beginning of the low bed 1 x on the gooseneck (overhanging) 1 x behind the last axle, recessed into the floor Coupling device, trailer turntable Tow hitch with tested 50 mm drawbar eye, drawbar eye inclined 8°, D-value min. 160 kN Axles + Suspension Drum brake axles Parabolic suspension with maintenance-free steel-rubber bearing and mechanical axle load equalization at the front and rear (rocker arm equalization) Wheels and Tires 235 / 75 R 17.5, according to the manufacturer's choice Steel rims in twin arrangement, factory silver Braking System 2-line compressed air braking system Spring brake parking brake 2 fail-safe coupling heads at the front, with connecting lines to the tractor unit ABS and ALB, with ABS connector at the front, with connecting cable Electrical System 24 Volt, multi-chamber lights, yellow LED lighting on the sides 2 white position lights at the front 2 white/red side marker lights at the rear 2 x 7-pole fail-safe connectors at the front, with connecting cable 1 LED rotating beacon with holder, switched via parking lights (beacon removable) 2 pairs of warning panels, double LED illuminated and extendable to 3,000 mm Floor Gooseneck at the front with steel/diamond plate covering followed by 70 mm soft wood flooring, steel/diamond plate covering in the wheel arch area Rear slope with 70 mm soft wood flooring Ramps Steel ramps 2,800 mm long, 750 mm wide, laterally adjustable covered with wood with spring-assisted support Country of Registration/Signs Bjdpfxsi Ri A So Aaroli Country of Registration: Germany 24/7 service hotline prepared for license plate holder, two lines Contour marking with reflective strips according to ECE R 048, white on the sides and red at the rear Warning sign according to ECE - 70 Paintwork Frame hot-dip galvanized including passivation, 15-year

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 7,150 kg, maximum load weight: 16,850 kg, overall weight: 24,000 kg, axle configuration: 3 axles, loading space width: 2,520 mm, total length: 11,990 mm, total width: 2,550 mm, suspension: air, tire size: 235 / 75 r 17,5, tire condition: 100 %, Customized transport solution Configure your Fliegl vehicle according to your requirements. The vehicle shown is an example. Production and equipment are carried out individually according to customer requirements. More information Chassis Steel welded construction Turntable with heavy-duty ball bearing, storage box recessed in the turntable extension Foldable rear support 2 support wedges with holder Aluminum side impact protection Splash guards at the rear over the entire width Extendable widening sections to 3,000 mm (not in the rear slope) Storage compartment for wooden planks in the center of the loading area Wooden planks 70 mm for widening to 3000 mm Tie-down eyes for low-bed trailers 3 pairs of tie-down points, each with 10 tons capacity, integrated in the floor at the front 6 pairs of tie-down recesses on the top and sides of the outer frame, each with 10 tons capacity 1 x near the gooseneck area the rest distributed in between, with a distance of no more than 1200 mm 1 x rear slope 5 pairs of lashing pockets recessed in the outer frame, 70 x 40 mm inside, (convertible to 5-ton ring tie-down eyes, not included in the scope of supply) Coupling device for trailer turntable Drawbar with tested 40 mm drawbar eye Axles + Suspension SAF drum brake axles Axle / chassis laser-aligned, reducing tire wear and fuel consumption Bjdpfei Riy Eex Aareli Parabolic suspension with maintenance-free steel-rubber bearing and mechanical Axle load equalization (rocker equalization) Braking system 2-line compressed air braking system Color-coded line routing for easy servicing Spring-loaded parking brake including 2 fail-safe coupling heads at the front, with connecting lines to the towing vehicle, ABS and ALB, with ABS plug at the front, with connection cable, Note: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Wheels and tires 235 / 75 R 17.5 at the manufacturer's choice Steel rims in twin arrangement, factory silver Electrical system 24 Volt, multi-chamber lights, yellow LED lighting on the side 2 white position lights at the front 2 white/red side marker lights at the rear 2 x 7-pin fail-safe plugs at the front, with connection cable, 1 LED rotating beacon with holder, switched via parking lights (beacon can be removed) 2 pairs of warning signs, double LED-illuminated and extendable to 3,000 mm Floor Front area with steel floor, then with 70 mm softwood floor, in the wheel arch area steel / tread plate covering Rear slope with 70 mm softwood floor Low-bed platform including rear slope 8,200 mm Ramps Steel ramps 2800 mm long, 750 mm wide, laterally movable covered with wood including with spring-loaded support Operating instructions An exemption permit is required for a 10,000 kg axle load; only indivisible loads are possible!!! The specified total weight is technically possible; depending on the cargo, the total weight may not be reached while complying with the permissible axle / support and saddle loads. Country of registration / signs Country of registration: Germany with Dekra approval and certificate (according to §13 EC - FGV) 24/7 service hotline prepared for two-line license plate holder Contour marking with reflective strips according to ECE R 048, white on the side and red at the rear Paint finish Frame DB 7350 Novagrau 10-year warranty against rust-through Drawbar galvanized or black, at the manufacturer's choice Ramps hot-dip galvanized Note: Archive images! Customized transport solution Configure your Flieg

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 6,100 kg, maximum load weight: 28,900 kg, overall weight: 35,000 kg, axle configuration: 3 axles, loading space length: 13,650 mm, loading space width: 2,480 mm, loading space height: 3,000 mm, total length: 13,850 mm, total width: 2,550 mm, total height: 1,060 mm, suspension: air, tire size: 435/50 r19.5, tire condition: 100 %, Additional information: Fine-grain steel welded construction, + Preload with light pretension in the neck area, turntable + with interchangeable 2 kingpins, outer frame slightly inclined, new design with Load-Lock profile for securing lashing straps, 24 tons, 2-speed support winch, single-sided operation, with straight lower section, without lateral thrust compensation. Note: Free support foot angle or free swivel radius to the rear approx. 1930 mm, extension ladder at the rear, door latch on the side, 2 support wedges with holder, side impact protection made of aluminum, under-run protection made of galvanized steel, quarter fender in front of the 1st axle and behind each axle, with anti-splash flaps according to EC, rear impact protection. SAF disc brake axles, axle/chassis laser-aligned to reduce tire wear and fuel consumption, air suspension. 2-line compressed air brake system, color-coded lines for easy servicing, spring brake parking brake, 2 non-interchangeable coupling heads at the front, without connecting line, EBS, electronic brake system with EBS socket at the front, without connecting cable. Caution: The trailer may only be pulled by towing vehicles that guarantee the effectiveness of the ABS! with raise and lower valve, vehicle stability system. 435/50R19.5, manufacturer's choice, steel rims, factory silver. 24 volts, multi-chamber lights, yellow LED lighting on the side, 2 white position lights at the front, 2 white/red side marker lights at the rear, 2 x 7-pole non-interchangeable sockets at the front, without connecting cable. Floor: Sieve-printed panels approx. 30 mm thick, on longitudinal supports for high point load capacity for forklift axle loads up to max. 7100 kg. Front wall/corner posts at the front: 2580 mm high, corner posts made of steel in a volumetric design, release mechanism for side tarpaulin on the front wall, crash blocker, at the bottom inside at a height of approx. 140 mm with steel impact protection. Center posts: 3 pairs of sliding posts that can be moved along the entire length, with 4-fold pockets and a long pocket at the bottom, 3 pairs of post positions. Sliding slats: 5 rows of wooden slats. Bedsi Ri E Hspfx Aareli Rear wall/corner posts at the rear: Corner posts at the rear made of steel up to the lower edge of the roof, attachment for tarpaulin with round tube and tarpaulin tensioning ratchet, rear portal doors, 2-leaf with 2 internal swivel locking mechanisms each. Tarpaulin: Tarpaulin with welded horizontal and vertical straps, tensioning buckles made of stainless steel. Roof: Sliding tarpaulin, rear end lift that can be folded up, with tarpaulin that can be slid from back to front, L-shaped roof rail for the automotive industry, internal width between the roof rails, approx. 2,490 mm, tarpaulin color: white, 400 roof non-elastic, minimal deflection of the roof rail during loading and unloading, optimal rain deflector at the rear, at the top of the end rail, above the doors, EcoLift - lifting roof can be raised by approx. 380 mm with gas spring support, 3 driving positions at the front: internal height at the front approx. 2900mm/2950 mm/3000 mm, set to approx. 3000 mm. Germany, test approval according to EC 2007/46, 24/7 service hotline, Fliegl manufacturer certificate for superstructure strength according to EN 12642 XL, prepared for single-row license plate holder, warning sign according to ECE - 70, reflective strips: white, continuously on the lower part of the side tarpaulin and at the top in the corn

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 7,900 kg, maximum load weight: 16,100 kg, overall weight: 24,000 kg, axle configuration: 2 axles, loading space width: 2,520 mm, loading space height: 900 mm, total length: 11,625 mm, total width: 2,550 mm, suspension: air, tire size: 235 / 75 r 17,5, tire condition: 100 %, Custom-tailored transport solution Configure your Fliegl vehicle according to your requirements. The vehicle shown is an example. Production and equipment are customized according to customer requirements. Further information Chassis Steel welded construction Turntable with heavy-duty ball bearing Foldable rear support 2 jacking plates with holder Splash guards at the rear over the entire width Preparation for widening to 3,000 mm (holes in the outer frame and not in the rear slope) Tie-down eyes, low loader 1 pair of tie-down recesses embedded in the front longitudinal member on the extension, 10 tons each 7 pairs of tie-down studs embedded in the top and sides of the outer frame, 10 tons each 1 x at the front on the extension 5 x in the low bed 1 x in the rear slope 12 pairs of tie-down holes in the outer frame, 5 tons each (for securing tie-down straps) 5 x on the extension, 6 x in the low bed and 1 x in the rear slope Coupling device, trailer turntable Tow hitch with tested 40 mm drawbar eye Axles + Suspension Drum brake axles, at the manufacturer's choice Axle/chassis laser-aligned to reduce tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearing and mechanical axle load equalization (lever equalization) Wheels and tires 235 / 75 R 17.5 Fulda Steel rims in twin arrangement, factory silver Braking system 2-circuit compressed air braking system Spring-loaded parking brake 2 fail-safe coupling heads at the front, with connecting lines to the towing vehicle Connecting lines extended by approx. 60 cm Without ABS, but with mechanical ALB, then max. 60 km/h approval Electrical system 12 Volt, multi-chamber lights, without yellow LED lighting on the sides, side reflectors 2 white position lights at the front 2 white/red side marker lights at the rear 1 x 7-pin 12 Volt plug at the front, with connecting cable, extended by approx. 60 cm 1 LED rotating beacon with holder, switched via parking lights (beacon removable) 2 pairs of illuminated and extendable warning signs to 3,000 mm Floor Front extension with steel/non-slip sheet covering Storage box embedded in the ramp to the extension Followed by 70 mm soft wood floor, steel/non-slip sheet covering in the wheel arch area Rear slope with 70 mm soft wood floor Low loader bed incl. rear slope 5900 mm Ramps Steel ramps 2,800 mm long, 750 mm wide, laterally movable Covered with wood With spring-loaded support Blsdpfoi Ri Agox Aaroi Operating instructions With 10,000 kg axle load, an exemption permit is required, only indivisible loads are possible!!! The specified total weight is technically possible, depending on the cargo, the total weight may not be achieved while complying with the permissible axle/support and drawbar loads. (Poor driving and handling behavior possible due to incorrect load distribution) Registration country / signs Registration country: Germany With Dekra approval and report, for max. 60 km/h approval, towing vehicle LoF (registration country Switzerland max. 40 km/h possible) Prepared for license plate holder, two lines Without contour marking / reflective strips according to ECE R 048 Painting Frame DB 7350 Novagrau 10 years warranty against rust perforation Tow hitch galvanized or black, at the manufacturer's choice Ramps hot-dip galvanized Note: Archive images!

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 6,200 kg, maximum load weight: 28,800 kg, overall weight: 35,000 kg, axle configuration: 3 axles, loading space length: 13,650 mm, loading space width: 2,480 mm, loading space height: 2,600 mm, total length: 13,850 mm, total width: 2,550 mm, total height: 4,045 mm, tire size: 385/65 r22.5, tire condition: 100 %, Customized Transport Solution Configure your Fliegl vehicle according to your requirements. The vehicle shown is an example. Production and equipment are customized according to customer requirements. Further information Fine-grain steel welded construction, kingpin plate with interchangeable 2-inch kingpin, slightly sloping outer frame, new design with Load-Lock profile for securing lashing straps, 24-ton capacity, two-stage landing gear, single-side operation, with straight lower section, without horizontal load compensation. Note: Free support leg swivel angle or free swivel radius to the rear approx. 1930 mm, extension ladder at the rear, door lock on the side, 2 wheel chocks with holder, Aluminum side impact protection, galvanized steel under-run protection, quarter panel fenders in front of and behind the axle assembly, with anti-splash flaps according to EG standard, rear impact protection. SAF disc brake axles with 430 mm disc diameter, axle/suspension laser-aligned to reduce tire wear and fuel consumption, air suspension. Two-line compressed air brake system, color-coded lines for easy servicing, spring-loaded parking brake, 2 tamper-proof coupling heads at the front, without connecting line, EBS, electronic brake system with EBS socket at the front, without connecting cable. Note: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with raise and lower valve, vehicle – driving stability system. 385/65R22.5, manufacturer's choice, steel rims, factory silver. 24 Volt, multi-chamber lights, yellow LED lighting on the sides, 2 white position lights at the front, 2 white/red marker lights at the rear, 2 x 7-pole tamper-proof sockets at the front, without connecting cable. Floor: Sieve-printed panels approx. 30 mm thick, mounted on longitudinal supports for high point load capacity for forklift axle loads up to a maximum of 7100 kg. Front wall/corner posts at the front: 2580 mm high, corner posts made of steel in a full-volume design, release device for side tarpaulin on the front wall, crash barrier, at the bottom inside at a height of approx. 140 mm with steel impact protection. Side supports: 3 pairs of sliding supports that can be moved along the entire length, with 4-fold insertion pockets and at the bottom with a long pocket, 3 pairs of support positions. Insertion slats: 5 rows of wooden insertion slats. Rear wall/corner posts at the rear: Corner posts made of steel at the rear up to the lower edge of the roof, attachment for tarpaulin with round tube and tarpaulin tensioning ratchet, rear portal doors, 2-leaf with 2 internal swivel latch locks each. Tarpaulin: Tarpaulin with welded horizontal and vertical straps, tensioning closures made of stainless steel. Roof: Sliding roof, rear lift that can be folded up, with the roof that can be slid from back to front, L-shaped roof beam for the automotive industry, internal width between the roof beams, approx. 2490 mm, tarpaulin color: white, 400 Roof non-elastic, minimal deflection of the roof beam during loading and unloading, optimal rain strip at the rear, at the top of the rear crossbar, above the doors. Bledpfx Aoi Riy Tearoi Germany, test approval according to EG 2007/46, 24/7 service hotline, Fliegl manufacturer's certificate for structural integrity according to EN 12642 XL, prepared for single-row license plate holder, warning sign according to ECE - 70, reflective strips: white, continuously on the side tarpaulin at the bottom and at the top in the co

Condition: new, machine/vehicle number: Produktpalette, empty load weight: 6 kg, maximum load weight: 28 kg, overall weight: 35 kg, axle configuration: 3 axles, loading space length: 15,030 mm, loading space width: 2,480 mm, loading space height: 4,060 mm, total length: 15,150 mm, total width: 2,550 mm, total height: 4,060 mm, suspension: air, tire size: 435/50R19,5, tire condition: 100 %, Additional information Chassis, semi-trailer, transport company Fine-grained steel welded construction, with preload for slight tension in the neck area, kingpin plate with interchangeable 2 kingpins X-tra Long, with an internal length of 15030 mm Outer frame slightly angled, new design with Load-Lock profile for attaching lashing straps 24-ton, 2-speed landing gear, single-side operation, with straight lower part, without thrust compensation Note: Free support foot angle or free swivel radius to the rear approx. 1930 mm Retractable ladder at the rear Blodoi Riwuopfx Aarji Door lock on the side 2 chocks with holder Aluminum side impact protection Galvanized steel under-ride protection Partial wheel arches in front of the 1st axle and behind each axle Rear impact protection Axles + Suspension SAF disc brake axles Axle/chassis laser-aligned to reduce tire wear and fuel consumption Air suspension Braking system 2-line compressed air braking system Color-coded lines for easy servicing Spring brake parking brake 2 non-interchangeable coupling heads at the front, without connecting line EBS, electronic braking system with EBS socket at the front, without connecting cable Caution: The semi-trailer may only be pulled by towing vehicles that guarantee the effectiveness of the ABS! with lifting and lowering valve Vehicle driving stability system AAC Basic, automatic lift axle acting on the last axle, as an aid for maneuvering, up to 20 km/h, can be manually switched off Axle load detection via EBS-Canbus signal, for display on the driver's cab, truck must be appropriately prepared, no truck installation (no calibrated scale) Wheels & Tires 435/50R19.5, manufacturer's choice Steel rims, factory silver Electrical system 24 Volt, multi-chamber lights, yellow LED lighting on the side Yellow LED lighting on the side coupled with the turn signal, flashing Side marker lights 2 white position lights at the front 2 white/red side marker lights at the rear 2 x 7-pole non-interchangeable sockets at the front, without connecting cable Floor Sieved plywood, approx. 30 mm thick, on longitudinal supports for high point load capacity for forklift axle load up to max. 7100 kg Front wall / Corner posts at the front 2580 mm high, corner posts steel in full volume design, release mechanism for side tarpaulin on the front wall, crash blocker, at the bottom inside at approx. 140 mm height with steel impact protection Center posts 3 pairs of sliding posts that can be moved along the entire length, with 4-fold insert pockets & at the bottom with a long pocket. 3 pairs of post positions Insert slats 5 rows of wooden slats Rear wall / Corner posts at the rear Corner posts at the rear steel up to the lower edge of the roof, attachment for tarpaulin with round tube and tarpaulin tensioning ratchet Rear portal doors, 2-wing with 2 internal swivel latch locks each Tarpaulin Tarpaulin, with welded-in horizontal and vertical straps Tensioning closures made of stainless steel Roof Sliding roof, rear end lift that can be folded up, with roof that can be slid from back to front, L-roof beam for the automotive industry, interior width between the roof beams approx. 2490 mm, tarpaulin color: white Roof non-elastic, hardly any deflection of the roof beam during loading and unloading EcoLift - liftable roof by approx. 380 mm, on both sides, with gas spring support, 3 driving positions at the front: Interior height at the front set to approx. 3000 mm Optimal rain gutter at the rear, at the top of the end ra

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 3,200 kg, maximum load weight: 35,800 kg, overall weight: 39,000 kg, axle configuration: 3 axles, tire size: 385/65 r22.5, Customized transport solution Configure your Fliegl vehicle according to your requirements. The vehicle shown is an example. Production and equipment are customized to meet individual customer needs. More information Fine-grained steel welded construction in lightweight design, fifth wheel plate with 2 replaceable kingpins, only 2 longitudinal beams as double T-beams for subsequent front drawbar coupling in new/current design, outer frame slightly angled with Load-Lock profile for securing lashing straps. Note: to attach the straps in conjunction with the sideboards, the sideboards must be opened!, 24 tons, 2-speed landing gear, single-sided operation, with straight lower part, without push-pull compensation, shims with holder, aluminum side impact protection, foldable, Bodpoi Riwqjfx Aarsli steel under-run protection, galvanized, extendable, half-shell mudguards!!Supplied loose, not mounted!!, with anti-splash flaps behind each axle, 1 plastic water tank, capacity approx. 30 liters, on the left side in the front BPW disc brake axles with 430 mm disc diameter, axle/suspension laser-aligned to reduce tire wear and fuel consumption, air suspension, 1st axle automatic lift axle, additionally manually lowerable, operable with a hand knob on the vehicle 2-line pneumatic brake system, with 1 central standard air reservoir, spring brake parking brake, 2 tamper-proof coupling heads at the front, without connecting line, EBS, electronic braking system with EBS socket at the front, without connecting cable, EBS 2S/2M, test connection for brake cylinder pressure on the EBS module routed to the outside, attention: the trailer may only be towed by towing vehicles which ensure the effectiveness of the ABS!, with lifting and lowering valve, control unit + brake integrated into the frame as in a semi-trailer tipper, mounted in front of the axles Brake pad wear indicator on disc brakes via ABS/EBS indicator light on the truck 385/65 R22.5, Continental brand, steel rims, factory silver 24 Volt, multi-chamber lights, yellow LED lighting on the side as in a semi-trailer tipper, dimension 3000 mm must be observed, 2 white position lights at the front in LED, loose, 2 white/red outline lights at the rear, 2 x 7-pole tamper-proof sockets at the front, without connecting cable Germany, type approval according to EC 2007/46 for the complete vehicle, 24/7 service hotline, prepared for a double license plate holder in a single row: 1 x plastic and 1 x stainless steel interchangeable holder Warning sign according to ECE - 70, aluminum, loose, EBS, safe parking, without contour marking / reflective strip according to ECE R 048, Frame: DB 7350 Novagrau, landing gear: black coated Immediately available! Customized transport solution Configure your Fliegl vehicle according to your requirements. The vehicle shown is an example. Production and equipment are customized to meet individual customer needs.

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 6,350 kg, maximum load weight: 28,650 kg, overall weight: 35,000 kg, axle configuration: 3 axles, tire size: 435/50 r19,5, tire condition: 100 %, Additional Information Chassis, Semi-trailer, Transport Company Fine-grained steel welded construction, kingpin plate with 2 replaceable kingpins Attachment rail for aluminum ramps across the entire width Reinforced frame for vehicle loading Outer frame with Load-Lock profile approximately every 400 mm for securing lashing straps 10 pairs of lashing eyes recessed in the outer frame, each rated at 10 tons 24-ton, 2-speed support winch, single-sided operation, with semi-circular lower part and straight connecting plate, with extension compensation Foldable rear support 2 chock blocks with holder Aluminum side underrun protection Galvanized steel underrun protection Quarter panel fenders in front of the 1st axle and behind each axle with anti-spray flaps behind each axle Pair of ferry eyes, yellow marked 1 spare wheel holder for 1 spare wheel, with wheel fastening kit Bedpeld Ihlsfx Aarsli 2 plastic toolboxes, with drawer and insert, w=650 / h=520 / d=670 mm, lockable with a padlock (lock not included) Container locking system, 4 pairs of locks recessed in the floor for 2 x 20 ft or 1 x 40 ft containers 10 pairs of lashing pockets recessed in the outer frame, internal dimensions 70 x 40 mm 10 lashing pockets recessed in the center of the floor, internal dimensions 70 x 40 mm 2 lashing/lashing bar rails recessed transversely in the floor across the entire width up to the outer frame (max. usable internal width between the outer lashing bars approx. 2170 mm), approx. 100 mm high. With 20 mm round steel rails, top and bottom, distance from top to bottom approx. 60 mm (of the round steel). Bottom with an angle plate as a closure, open halfway downwards. For lashing and inserting lashing bars 80 x 80: Position 2 and 4 according to Fliegl data sheet 20 lashing bars, hot-dip galvanized Note: The lashing pockets / insertion pockets are not designed for the sole securing of long materials, pipes, etc. without wrapping. Storage space for aluminum access ramps, ramps can be slid in from the rear 3 pairs of folding eyes, 10 tons, in the outer frame (1x in front of the front wall and 2x in the rear area). Axles + Suspension SAF disc brake axles Axle / chassis laser-measured, reduces tire wear and fuel consumption Air suspension 1st axle automatic lift axle, including forced lowering and start-up assistance, actuated by 3x brake (start-up assistance is functional up to an axle load exceeding 30% and up to a speed of max. 25 km/h) Axle lift below the recommended ride height, therefore no guarantee for tire damage 2 ride heights, adjustable via hand knob, 1 x for saddle height 980 mm, 1 x for saddle height 1100 mm (Note! Vehicle with tilt) Braking System 2-line pneumatic braking system Color-coded line routing for easy servicing Spring-loaded parking brake 2 non-interchangeable coupling heads at the front, without connecting line EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The semi-trailer may only be pulled by towing vehicles that guarantee the effectiveness of the ABS! with lifting and lowering valve 2 ride heights, adjustable via hand knob, 1 x for saddle height 980 mm, 1 x for saddle height 1100 mm (Note! Observe overall height, exceeding height is at the customer's risk) Ride height in connection with lift axle, with the lift axle raised, the loading or overall height increases by 50 mm (with Mega Flex only at the lower ride height or saddle height) Vehicle - Driving stability system Wheels and tires 435/50 R19.5, manuf

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 5 kg, maximum load weight: 29 kg, overall weight: 35 kg, axle configuration: 3 axles, total length: 13,990 mm, total width: 2,550 mm, tire size: 385 / 65 r 22,5, tire condition: 100 %, Customized transport solution Configure your Fliegl vehicle according to your requirements. The vehicle shown is an example. Production and equipment are tailored to individual customer needs. Further information Chassis, semi-trailer, forwarding company Steel welded construction in reinforced design, only 2 longitudinal beams as double T-beams with steel/diamond plate between the longitudinal beams, kingpin plate with 2 interchangeable kingpins. Mudguard for taillights. 1 steel storage box, recessed between longitudinal beams 8 pairs of lashing eyes screwed or welded to the frame, as per manufacturer's choice 24 tons, 2-speed support winch, single-sided operation, with straight lower part, without thrust compensation 2 support wedges with holder Aluminum side underrun protection Galvanized steel rear underrun protection Semi-shell mudguards with anti-splash flaps according to EG 1 spare wheel holder for 1 spare wheel, with wheel fastening kit 8 pieces of timber rack brackets, as per manufacturer's choice, screwed to the frame with 2 extendable timber racks each, from 1800 to 2800 mm, 7 tons per pair Axles + Suspension SAF disc brake axles with 430 mm disc diameter Air suspension with lifting and lowering valve, safety cable on the axles 1st axle automatic lift axle, including forced lowering and starting assist, activated by 3x braking (starting assist is functional up to an axle load exceeding 30% and up to a speed of max. 25 km/h) Bjdsi Rivwopfx Aaroli Offset axle spacing mm (combined transport) up to 44 tons total weight Wheels and tires 385 / 65 R 22.5 as per manufacturer's choice Steel rims, factory silver Braking system 2-line pneumatic braking system Spring-loaded parking brake Axle load detection via EBS-Canbus signal, for display on the screen in the driver's cab, the truck must be correspondingly pre-equipped, no truck installation (no calibrated scale) 2 non-interchangeable coupling heads at the front, without connection cable EBS, electronic braking system with EBS socket at the front, without connection cable Note: The trailer may only be pulled by towing vehicles that guarantee the effectiveness of ABS! Electrical system 24 volts, multi-chamber lights, yellow LED lighting on the sides 2 white position lights at the front 2 white/red marker lights at the rear 2 x 7-pole and 1 x 15-pole non-interchangeable sockets at the front, without connection cable Front panel/corner posts at the front Steel/lattice front panel, approx. 2,300 mm high, screwed to the frame Approval / Signs Country of approval: Germany Type approval according to EG 2007/46 prepared for single-row license plate holder Contour marking with reflective tape according to ECE R 048, white on the sides and red at the rear Paint Frame DB 7350 Novagrau Support feet black coated Front panel hot-dip galvanized Note: Archive images! Customized transport solution Configure your Fliegl vehicle according to your requirements. The vehicle shown is an example. Production and equipment are tailored to individual customer needs.

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 5,000 kg, maximum load weight: 23,000 kg, overall weight: 28,000 kg, axle configuration: 2 axles, loading space height: 900 mm, total length: 13,800 mm, total width: 2,550 mm, total height: 2,638 mm, suspension: air, tire size: 235/75 r17,5, tire condition: 100 %, Customized transport solution Configure your Fliegl vehicle according to your requirements. The vehicle shown is an example. Production and equipment are customized according to customer requirements. More information Chassis, semi-trailer, transport company Fine-grained steel welded construction, kingpin plate with 2 replaceable kingpins Outer frame slightly inclined, new design with Load-Lock profile for attaching lashing straps 24 tons, 2-speed landing gear, single-sided operation, with straight lower part, without push-pull compensation Free support foot angle or free swivel radius to the rear, approx. 1920 mm 2 chocks with holder Aluminum side underrun protection Steel rear underrun protection Quarter panel fenders in front of and behind each axle 1 spare wheel holder for 1 spare wheel, with wheel fastening kit 1 plastic toolbox, with insert, w=620/h=360/d=440 mm, lockable with a padlock. (Lock not included) Axles + Suspension Drum brake axles, selection according to manufacturer Laser-measured axle/chassis alignment, reduces tire wear and fuel consumption Air suspension Braking system 2-line compressed air braking system, color-coded lines for easy servicing Bljdpfxskv Uvzs Aarsi Spring brake parking brake Duomatic connection at the front, without connecting line EBS, electronic braking system with EBS socket at the front, without connecting cable Note: The trailer may only be towed by towing vehicles that ensure the effectiveness of the ABS! with lifting and lowering valve Vehicle - driving stability system Wheels and tires 235/75 R17.5, manufacturer's choice Steel rims, factory silver Electrical system 24 volt, multi-chamber lights, yellow LED lighting on the sides 2 white position lights at the front 2 white/red marker lights at the rear 1 x 15-pin socket at the front, without connecting cable Floor Sieve-printed panels, approx. 30 mm thick, for high point load capacity, for forklift axle load up to max. 5,600 kg Front wall / corner posts 25 mm aluminum hollow profile, approx. 1,350 mm high, corner posts made of steel in a volumetric design Country of approval / plates Germany with Dekra inspection and certificate (according to §13 EG - FGV) 24/7 service hotline prepared for single-line license plate holder Contour marking with reflective strips according to ECE R 048, white on the sides and red at the rear Paintwork Frame hot-dip galvanized including passivation, 15 years warranty against rust Front wall aluminum Note: These are archive images! Customized transport solution Configure your Fliegl vehicle according to your requirements. The vehicle shown is an example. Production and equipment are customized according to customer requirements.

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 6,860 kg, maximum load weight: 28,140 kg, overall weight: 35,000 kg, axle configuration: 3 axles, suspension: air, tire size: 235/75 17,5, tire condition: 100 %, Additional information Chassis Fine-grained steel welded construction, kingpin plate with 2 replaceable kingpins Recessed rail for loading ramps on the rear extension over the entire width, outer edge beveled to prevent damage. Reinforced frame for vehicle loading Outer frame with load-lock profile approx. every 400 mm for securing lashing straps 10 pairs of lashing eyes recessed on the top/outside of the outer frame, each 10 tons, starting after the neck area 24-ton, 2-speed support jacks, single-sided operation, with a flat mounting plate 2 wheel chocks with holder Aluminum side impact protection Galvanized steel underride protection Sheet metal as a splash guard riveted to the bottom, in the neck area above the center of the bogie axle and above the axle assembly Semi-elliptical fenders with anti-spray flaps according to EC Bjdjlf Dtmjpfx Aarjli Container locking system, 4 pairs of locking recesses recessed in the floor for 2 x 20 ft or 1 x 40 ft containers, 4 pairs of container locking adapters (additional cross supports required at the front and rear of the container; the container must rest evenly across its width in conjunction with the locks; cross supports are not included) Attention! Damage to the platform floor is possible due to the cross supports! Rear extension, mechanical, with hand crank, extendable by approx. 1500 mm, lockable every 500 mm, including extendable underride protection with lighting (then the rear ladder is omitted) Covered with platform in the wheel arch area, with steel diamond plate in the center. Attention! Ramp loading at the rear is only possible with the rear extension in the retracted position! Storage space for loading ramps integrated in the rear extension, only usable when the rear extension is extended 1000 mm – then there is an overhang For transporting the ramps with the rear extension retracted, there is storage space for the ramps on the right side of the frame in front of the axles 1 pair of ramps, 3000 mm long, 300 mm wide, load capacity per pair 6000 kg (recessed rail for ramps on the rear extension) Rear slope to approx. 500 mm Electric winch, 24 volts, pulling force approx. 8165 kg, mounted in the center at the front, operated with a wireless remote control, cable length 35 m x approx. 10 mm, with a cable guide and removable guide rollers Axles + Suspension Drum brake axles Axle/suspension laser-aligned to reduce tire wear and fuel consumption Air suspension 1st axle automatic lift axle, including forced lowering and start-up assistance, activated by 3x braking (start-up assistance functions up to an axle load exceedance of 30% and a speed of max. 25 km/h) with central lift arm Axle lift below the recommended ride height, therefore no guarantee for tire damage Braking system 2-line pneumatic braking system Color-coded lines for easy service. Spring parking brake 2 non-interchangeable coupling heads at the front, without connecting line EBS, Electronic Braking System with EBS socket at the front, without connecting cable Attention: The trailer may only be pulled by towing vehicles which guarantee the effectiveness of the ABS! with raise and lower valve Vehicle - driving stability system Wheels and tires 235/75 17.5, manufacturer's choice Steel rims in twin arrangement, factory silver Electrical system 24 volts, multi-chamber lights, yellow LED lighting on the side 2 white position lights at the front in LED 2 white/red marker lights at the rear 2 additional LED work lights at the rear, switched via the revers

Condition: used, empty load weight: 5,100 kg, maximum load weight: 32,900 kg, overall weight: 38,000 kg, axle configuration: 3 axles, first registration: 07/2024, next inspection (TÜV): 09/2026, total length: 9,500 mm, total width: 2,550 mm, suspension: air, tire size: 385/55 R 22,5, tire condition: 50 %, Year of construction: 2024, Equipment: ABS, Galvanized chassis, BPW disc brakes, 1st axle liftable, ADR, spare wheel holder, container carrier extendable centrally via tractor and mechanically at the rear, twist locks for all types of containers. Bedpfex Nh Hqsx Aareli

Condition: new, empty load weight: 6,600 kg, maximum load weight: 17,400 kg, overall weight: 24,000 kg, axle configuration: 3 axles, loading space length: 6,500 mm, total length: 10,900 mm, suspension: steel, tire size: 235/75 R17,5 (Doppelbereifung), color: silver, gearing type: mechanical, fuel consumption (urban): 1,090 l/100km, Empty weight: 6600kg, permissible total weight: 24000kg, loading space length: 6,500 mmTire size: 235/75 R17.5, 1st axle: , 2nd axle: , 3rd axle: , leaf spring suspension, 3 axle low loader trailer with offset DTS-S 300 - bogie with strong ball bearing ring - foldable rear support - 1 spare wheel holder for 1 electric bike, with wheel fastening kit - 1 spare wheel, same make as basic tires, steel rim - 1 plastic tool box - extensions extendable to 3000mm (not in rear bevel) - storage compartment for wooden planks in the middle of the low load area - wooden planks 70mm for extension to 3000mm Lashing eyes low loader: - with spring jack Support axles + suspension: - SAF - drum brake axles - Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation (rocker compensation) Brake system: - 2-line compressed air brake system - Spring-loaded parking brake Electrics: - 24 volt, multi-chamber lights, yellow LED lighting on the side - 1 LED rotating beacon with holder, switched via parking light (light removable) - 2 pairs of warning signs with double LED lighting and extendable to 3000 mm Floor: - Storage box embedded in the crossing slope to the crank - then with 70 mm softwood floor, steel / checker plate covering in the wheel arch area - Rear bevel with 70 mm softwood floor Loading ramps: Steel ramps 2,800 mm long, 750 mm wide, laterally movable, covered with wood - - 1 pair of ring lashing eyes embedded on the crank at the front, 10 tonnes - 4 pairs of lashing holes in the AR with 5 tonnes each for tensioning belt attachment - 7 pairs Lashing eyes at the top and sides of the outer frame, 10 tonnes each - 1 x at the front on the crank, 6 x in the low bed - 5 pairs of stake pockets in the outer frame, inside 70x40 mm (can be converted to 5 tonne ring lashing eyes for an additional charge) - 2 pairs of additional folding lashing eyes, 10 tonnes each, 1x at the front on the crank, 1x behind the 3rd axle, axles + suspension: - SAF - drum brake axles - parabolic suspension with maintenance-free steel-rubber bearings and mechanical Ac Blodpetcwkrsfx Aarei

Condition: new, axle configuration: 3 axles, color: grey-black, gearing type: mechanical, Colour natural, lifting axle, electronic braking system EBS, connection plug 1x15-pin, equipment outer frame slightly slanted, new version with "Load-Lock profile" for attaching tensioning belts, 13 pairs of lashing eyes additionally in the outer frame, each 5 to 24 tonnes. 2-speed support winch, one-sided operation, with semi-circular lower section and straight forklift ram protection made of steel on the outer frame on the side. and rear 1 spare wheel holder for 1 electric bike, with wheel fastening kit 1 plastic tool box 650mmx520mmx670mm 7 pairs of stake pockets embedded in the outer frame, 83 x 83 mm SAF disc brake axles with 430 mm air suspension 1st axle automatic lift axle, including forced lowering and starting aid, actuation of 3x brakes Wheels and tires 6 385/65 R22.5" Make 6 steel rims, factory silver Floor screen-printed panels approx. 30 mm thick, cross joints with omega insert, for high point load capacity for forklift axle load up to max. 7 100 kg Front wall / corner stanchions front 25 mm aluminum hollow profile, 1 950 mm high, corner stanchions steel in volume design + 2 center supports "crash blocker", bottom inside at approx. 140 mm height Side walls 25 mm aluminum hollow profile, 700 mm high Paintwork frame hot-dip galvanized including passivation "15 year guarantee against rust through" side walls ALU anodized, errors and changes reserved. Blsdpfx Aetcwmioarei

Condition: new, functionality: fully functional, overall weight: 16,000 kg, maximum load weight: 13,700 kg, empty load weight: 2,300 kg, loading space width: 2,480 mm, loading space length: 7,750 mm, loading space height: 3,000 mm, machine/vehicle number: Produktpalette, Customized Transport Solution Configure your Fliegl vehicle to meet your specific requirements. The vehicle shown is an example. Production and equipment are customized according to customer specifications. Tandem Trailer Chassis Welded steel construction with a floor assembly approximately 152 mm high; load-bearing and torsionally rigid steel frame construction. Longitudinal beam floor construction with a load-resistant outer frame and guide tunnels spaced 600 mm apart; tunnels feature guides on top and sides, tunnel height approx. 45 mm; 4 x swap body corner fittings based on a 20-foot standard. 4 side-extending/folding parking feet with dual locking mechanism for a parking height of 970 mm, with support leg rest Blodpfokt Ni Ujx Aarsi Side door stops Rear impact protection made of flat bar Pallet stops on both sides, approx. 20 mm high with perforated profile for securing straps; loading height is reduced by approx. 20 mm Floor Screen-printed panels approx. 27 mm thick, for high point load capacity, for forklift axle load up to max. 4,400 kg Front wall/corner stanchions Approx. 2,580 mm high, remainder covered with tarp; steel corner stanchions in full-size design; release mechanism for side tarp on front wall Inner front wall additionally lined with a 1,250 mm high screen-printed panel Center stanchions 1 pair of sliding stanchions adjustable along the entire length, with 4-compartment pockets and a long pocket at the bottom. 1 pair of stanchion positions Slotting Slats 5 rows of wooden V-shaped slotting slats Rear wall/rear corner stanchions Rear steel corner stanchions extending to the bottom edge of the roof, tarpaulin attachment with round tube and tarpaulin tensioning ratchet Rear portal doors, double-leaf, each with 2 internal twist-lock latches Tarpaulin Tarpaulin, with welded-in horizontal and vertical straps, reinforcements for stanchions Stainless steel tensioning fasteners Roof Sliding roof, rear end lift folds up, roof can be slid from rear to front, L-shaped roof rail for the automotive industry, interior width between roof rails approx. 2,490 mm, tarpaulin color: white EcoLift – lifting roof by approx. 380 mm, liftable on both sides, with gas spring assistance, Registration / Plates Country of registration: Germany Fliegl manufacturer’s certificate for body strength in accordance with EN 12642 XL, Fliegl manufacturer’s certificate for body strength in accordance with DL 9.5, pallet stops on both sides, approx. 20 mm high, loading height reduced by approx. 20 mm Fliegl manufacturer’s certificate for load securing in accordance with VDI 2700, Sheet 12 ff. Pallet stops on both sides, approx. 20 mm high; loading height is reduced by approx. 20 mm Paint Finish Frame Hot-dip galvanized, including passivation Front corner posts Hot-dip galvanized Front wall Aluminum Rear corner posts Hot-dip galvanized Rear wall White

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 11,000 kg, maximum load weight: 27,000 kg, overall weight: 38,000 kg, axle configuration: 3 axles, loading space length: 9,500 mm, loading space width: 2,480 mm, loading space height: 3,040 mm, total length: 13,800 mm, total width: 2,550 mm, total height: 4,020 mm, suspension: air, tire size: 235 / 75 r 17,5, tire condition: 100 %, Custom-made transport solution Configure your Fliegl vehicle according to your requirements. The vehicle shown is an example. Production and equipment are customized according to customer requirements. Chassis Steel welded construction with narrow crossmember spacing and reinforced design, low-loader outer frame profile, for transporting construction machinery up to 32,000 kg and with a maximum outer width of the construction machinery of 2550 mm, kingpin plate with replaceable 2 kingpins. Rear slope of approx. 1200 mm and 7°. Ramp shaft closed at the top with steel/diamond plate, in the low-bed, omega rail laterally at the bottom on the outer frame as a mounting rail for tarpaulin and spacers for lashing points, not in the wheel area. If a lift table is used, there is an additional, lightweight outer frame with an omega profile. 24-ton, 2-speed landing gear, single-sided operation, with a semi-circular lower part and a straight connection plate, with stroke compensation, free swivel radius to the rear approx.: 1950 mm, rear support, foldable 2 wheel chocks + holder Side underrun protection, aluminum Quarter panel fenders in front of and behind each axle with anti-splash flaps behind each axle Underrun protection, steel Splash flap at the rear over the entire width 4 storage boxes, stainless steel, w=800/h=350/d=350 mm, with a polished, lockable door, 2 x on the left front and 2 x on the right front in front of the 1st axle Lift table behind the gooseneck, approx. 3000 mm long, hydraulically liftable for crossing over the gooseneck, with mechanical locking in the raised position. (Cylinder angled for good ground clearance, Fliegl standard). Operation on the right front + additional activation with a wireless remote control, lift table can be raised with the tarpaulin closed! Tarpaulin attachment in the lift table area to an additional, lightweight outer frame with omega profile, lift table can be raised with the tarpaulin closed! Lashing points can also be used in the lowered position! Lashing points Gooseneck: 4 pairs of 5-ton lashing points embedded in the outer frame 2 pairs of lashing points at the top and on the side embedded in the outer frame 8 pairs of lashing points at the top and on the side embedded in the outer frame, each 10 tons 9 pairs of 5-ton lashing points embedded in the outer frame Axles + Suspension SAF drum brake axles last axle with trailing steering knuckle, with automatic reversing lock via reversing light, and additional locking function on the vehicle via hand button. Air suspension with lifting and lowering valve + auto-reset function H&S function with quick vent 1st axle, automatic lift axle, incl. forced lowering and starting assist, activated by pressing the brake pedal 3 times (starting assist is functional up to an axle load exceedance of 30% and a speed of max. 25 km/h) Axle lift below the recommended ride height, no guarantee for tire damage Wheels and tires 235/75R17.5 from leading manufacturers Bedpfx Aoi Riw Ajarjli Steel rims in twin arrangement, factory silver Braking system 2-line pneumatic braking system Spring brake parking brake 2 foolproof coupling heads at the front EBS, electronic braking system with EBS socket at the front, without connection cable Note: The trailer may only be towed by towing vehicles that ensure the effectiveness of the ABS! Axle load recognition in the truck via EBS, without installation in the truck. Electrical system 24 volts, multi-chamber lights, yellow LED lighting on the sides 2 white

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 3,000 kg, maximum load weight: 15,000 kg, overall weight: 18,000 kg, axle configuration: 2 axles, total length: 9,470 mm, total width: 2,550 mm, total height: 1,040 mm, suspension: air, tire size: 235/75 R17,5", tire condition: 100 %, Customized Transport Solution Configure your Fliegl vehicle to meet your specific requirements. The vehicle shown is an example. Production and equipment are customized according to customer specifications. *Chassis with swivel turntable Fine-grained steel welded construction Front stop, longitudinally adjustable and foldable 2 pairs of removable guide rollers, front and rear 1 pair of removable guide rollers, additional 4 container locks with sturdy 20"-based arms for swap bodies 7.15 and 7.45 Swivel frame with heavy-duty ball bearing swivel ring Wheel chocks with holder Aluminum side impact protection Side impact protection set inward for optimal clearance to the swap body supports Steel underrun protection Underrun protection shortened for optimal clearance to the swap body supports; lighting system mounted in a protected position Rear mud flaps across the entire width (not compatible with forklift mount) Quarter-shell front fenders and half-shell rear fenders *Towing equipment for trailer turntable Towing fork with certified 40 mm tow eye Towing fork mechanically adjustable in length by approx. 6 x 100 mm (approx. 1900–2500 mm), towing fork length set to 2200 mm *Axles + Suspension BPW or SAF drum brake axles, at the manufacturer’s discretion “Laser-aligned axles/chassis” to reduce tire wear and fuel consumption Bodpszfp Uxsfx Aarsli Air suspension *Brake System 2-line compressed air brake system Color-coded piping for easy maintenance. Air reservoir: 180 liters Spring-loaded parking brake 2 non-reversible coupling heads at the front, with connecting lines to the tractor unit, EBS, Electronic Braking System with EBS connector at the front, with connecting cable, Caution: The trailer may only be towed by tractor units that ensure the effectiveness of the ABS! With lift/lower valve, hold function in both lower and lift positions Axle load detection via EBS CAN bus signal, for display in the cab; truck must be equipped accordingly *Wheels and Tires 235/75 R17.5, brand selected by the manufacturer Steel rims in twin configuration, factory silver *Electrical System 24 volts, multi-chamber lights, yellow LED side lighting linked to the turn signals (“flashing side lights”), LED license plate lighting (Note: With certain towing vehicles, false diagnostics may occur even though the function is working properly) 2 white LED front position lights 2 white/red LED rear lane-keeping lights 2 x 7-pin reverse-polarity-protected connectors at the front, with connecting cable, LED work lights on both sides (activated via reverse light) 2 additional LED work lights at the rear, activated by the reverse light 1 LED work light at the front, centered between the cross members, shining toward the rear, activated by the reverse light *Country of Registration / License Plates Germany With DEKRA inspection and certification (in accordance with §13 EG - FGV) 24/7 Service Hotline Prepared for single-line license plate holders Contour markings with reflective strips in accordance with ECE R 048, white on the sides and red at the rear *Paint finish Hot-dip galvanized frame, including passivation “15-year warranty against rust-through” Drawbar: galvanized or black, at the manufacturer’s discretion Customized transport solution