Used Fliegl Open Flatbed Semitrailers for sale (340)

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 11,000 kg, maximum load weight: 27,000 kg, overall weight: 38,000 kg, axle configuration: 3 axles, loading space length: 9,500 mm, loading space width: 2,480 mm, loading space height: 3,040 mm, total length: 13,800 mm, total width: 2,550 mm, total height: 4,020 mm, suspension: air, tire size: 235 / 75 r 17,5, tire condition: 100 %, Custom-made transport solution Configure your Fliegl vehicle according to your requirements. The vehicle shown is an example. Production and equipment are customized according to customer requirements. Chassis Steel welded construction with narrow crossmember spacing and reinforced design, low-loader outer frame profile, for transporting construction machinery up to 32,000 kg and with a maximum outer width of the construction machinery of 2550 mm, kingpin plate with replaceable 2 kingpins. Rear slope of approx. 1200 mm and 7°. Ramp shaft closed at the top with steel/diamond plate, in the low-bed, omega rail laterally at the bottom on the outer frame as a mounting rail for tarpaulin and spacers for lashing points, not in the wheel area. If a lift table is used, there is an additional, lightweight outer frame with an omega profile. 24-ton, 2-speed landing gear, single-sided operation, with a semi-circular lower part and a straight connection plate, with stroke compensation, free swivel radius to the rear approx.: 1950 mm, rear support, foldable 2 wheel chocks + holder Side underrun protection, aluminum Quarter panel fenders in front of and behind each axle with anti-splash flaps behind each axle Underrun protection, steel Splash flap at the rear over the entire width 4 storage boxes, stainless steel, w=800/h=350/d=350 mm, with a polished, lockable door, 2 x on the left front and 2 x on the right front in front of the 1st axle Lift table behind the gooseneck, approx. 3000 mm long, hydraulically liftable for crossing over the gooseneck, with mechanical locking in the raised position. (Cylinder angled for good ground clearance, Fliegl standard). Operation on the right front + additional activation with a wireless remote control, lift table can be raised with the tarpaulin closed! Tarpaulin attachment in the lift table area to an additional, lightweight outer frame with omega profile, lift table can be raised with the tarpaulin closed! Lashing points can also be used in the lowered position! Lashing points Gooseneck: 4 pairs of 5-ton lashing points embedded in the outer frame 2 pairs of lashing points at the top and on the side embedded in the outer frame 8 pairs of lashing points at the top and on the side embedded in the outer frame, each 10 tons 9 pairs of 5-ton lashing points embedded in the outer frame Axles + Suspension SAF drum brake axles last axle with trailing steering knuckle, with automatic reversing lock via reversing light, and additional locking function on the vehicle via hand button. Air suspension with lifting and lowering valve + auto-reset function H&S function with quick vent 1st axle, automatic lift axle, incl. forced lowering and starting assist, activated by pressing the brake pedal 3 times (starting assist is functional up to an axle load exceedance of 30% and a speed of max. 25 km/h) Axle lift below the recommended ride height, no guarantee for tire damage Wheels and tires 235/75R17.5 from leading manufacturers Steel rims in twin arrangement, factory silver Braking system 2-line pneumatic braking system Spring brake parking brake 2 foolproof coupling heads at the front Bwsdpfx Acsi Riw Ajfjp EBS, electronic braking system with EBS socket at the front, without connection cable Note: The trailer may only be towed by towing vehicles that ensure the effectiveness of the ABS! Axle load recognition in the truck via EBS, without installation in the truck. Electrical system 24 volts, multi-chamber lights, yellow LED lighting on the sides 2 white

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 3,000 kg, maximum load weight: 15,000 kg, overall weight: 18,000 kg, axle configuration: 2 axles, total length: 9,470 mm, total width: 2,550 mm, total height: 1,040 mm, suspension: air, tire size: 235/75 R17,5", tire condition: 100 %, Customized Transport Solution Configure your Fliegl vehicle to meet your specific requirements. The vehicle shown is an example. Production and equipment are customized according to customer specifications. *Chassis with swivel turntable Fine-grained steel welded construction Front stop, longitudinally adjustable and foldable 2 pairs of removable guide rollers, front and rear 1 pair of removable guide rollers, additional 4 container locks with sturdy 20"-based arms for swap bodies 7.15 and 7.45 Swivel frame with heavy-duty ball bearing swivel ring Wheel chocks with holder Aluminum side impact protection Side impact protection set inward for optimal clearance to the swap body supports Steel underrun protection Underrun protection shortened for optimal clearance to the swap body supports; lighting system mounted in a protected position Rear mud flaps across the entire width (not compatible with forklift mount) Quarter-shell front fenders and half-shell rear fenders *Towing equipment for trailer turntable Towing fork with certified 40 mm tow eye Towing fork mechanically adjustable in length by approx. 6 x 100 mm (approx. 1900–2500 mm), towing fork length set to 2200 mm *Axles + Suspension BPW or SAF drum brake axles, at the manufacturer’s discretion “Laser-aligned axles/chassis” to reduce tire wear and fuel consumption Air suspension *Brake System 2-line compressed air brake system Color-coded piping for easy maintenance. Air reservoir: 180 liters Spring-loaded parking brake 2 non-reversible coupling heads at the front, with connecting lines to the tractor unit, EBS, Electronic Braking System with EBS connector at the front, with connecting cable, Caution: The trailer may only be towed by tractor units that ensure the effectiveness of the ABS! With lift/lower valve, hold function in both lower and lift positions Axle load detection via EBS CAN bus signal, for display in the cab; truck must be equipped accordingly *Wheels and Tires 235/75 R17.5, brand selected by the manufacturer Steel rims in twin configuration, factory silver *Electrical System 24 volts, multi-chamber lights, yellow LED side lighting linked to the turn signals (“flashing side lights”), LED license plate lighting (Note: With certain towing vehicles, false diagnostics may occur even though the function is working properly) 2 white LED front position lights 2 white/red LED rear lane-keeping lights Bwsdpfx Aezfp Uxjcfop 2 x 7-pin reverse-polarity-protected connectors at the front, with connecting cable, LED work lights on both sides (activated via reverse light) 2 additional LED work lights at the rear, activated by the reverse light 1 LED work light at the front, centered between the cross members, shining toward the rear, activated by the reverse light *Country of Registration / License Plates Germany With DEKRA inspection and certification (in accordance with §13 EG - FGV) 24/7 Service Hotline Prepared for single-line license plate holders Contour markings with reflective strips in accordance with ECE R 048, white on the sides and red at the rear *Paint finish Hot-dip galvanized frame, including passivation “15-year warranty against rust-through” Drawbar: galvanized or black, at the manufacturer’s discretion Customized transport solution

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 2,950 kg, maximum load weight: 15,050 kg, overall weight: 18,000 kg, axle configuration: 2 axles, total length: 9,470 mm, total width: 2,550 mm, total height: 1,080 mm, suspension: air, tire size: 445/45 R19,5", tire condition: 100 %, Customized Transport Solution Configure your Fliegl vehicle to meet your specific requirements. The vehicle shown is an example. Production and equipment are customized according to customer specifications. *Chassis with swivel turntable Fine-grained steel welded construction Fliegl “V-Stream” frame Front stop, longitudinally adjustable and foldable Pair of removable guide rollers, front and rear 4 container locks with sturdy arms based on 20" dimensions for 7.15 m and 7.45 m swap bodies (Note: When used in combination with the impact guard, the guard protrudes beyond the 7.15 m swap body) Note! Not suitable for 20" containers, or only possible if the container has a tunnel or opening at the front center measuring approx. 200 mm in length and 800 mm in width! Swivel mount with heavy-duty ball bearing swivel ring Wheel chocks with holders Aluminum side impact protection Side impact protection set inward for optimal clearance to the swap body supports Steel underrun protection Underrun protection shortened for optimal clearance to the swap body supports; lighting system mounted in a protected position Bwedpjzfp S Defx Acfep Quarter-shell fenders in front and half-shell fenders in the rear Includes mud flaps for fenders Large Fliegl mud flap mounted transversely on the underrun protection at the rear *Trailer coupling system (turntable) Drawbar with certified 40 mm drawbar eye *Axles + Suspension SAF disc brake axles “Laser-measured axles/chassis” reduces tire wear and fuel consumption Air suspension *Brake System 2-line compressed air brake system Color-coded lines for easy maintenance. Air reservoir capacity: 208 liters Spring-loaded parking brake 2 non-reversible coupling heads at the front, with connecting lines to the tractor unit, 24-volt EBS, electronic braking system with EBS connector at the front, with connecting cable, Caution: The trailer may only be towed by tractor units that ensure the effectiveness of the ABS! with lift & lower valve + auto-reset function Axle load detection via EBS CAN bus signal, for display in the cab; the truck must be equipped accordingly “TPMS” tire pressure monitoring system according to ECE R 141, display in the towing vehicle via EBS *Wheels and tires 445/45 R19.5", brand selected by the manufacturer Steel rims, factory silver *Electrical system 24 volts, multi-chamber lights, yellow LED side lighting Yellow LED side lighting linked to the turn signals “Flashing side lights” 2 white front position lights 2 white/red rear lane-keeping lights 1 x 15-pin connector at the front, with connecting cable, additional LED work light(s) at the rear, activated via the reverse light LED work light at the front, centered between the cross members, shining toward the rear, activated via the reverse light *Country of registration/license plates Germany with DEKRA approval and certification (in accordance with §13 EG - FGV) 24/7 service hotline prepared for single-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white on the sides and red at the rear *Chassis galvanized or painted in colour of choice

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 2,500 kg, maximum load weight: 15,500 kg, overall weight: 18,000 kg, axle configuration: 2 axles, total length: 9,470 mm, total width: 2,550 mm, total height: 1,260 mm, suspension: air, tire size: 385/65 R22,5", tire condition: 100 %, Customized Transport Solution Configure your Fliegl vehicle to meet your specific requirements. The vehicle shown is an example. Production and equipment are customized according to customer specifications. *Chassis with swivel turntable Fine-grained steel welded construction Fliegl “V-Stream” frame Front stop, longitudinally adjustable and foldable 2 pairs of removable guide rollers, front and rear 4 container locks with sturdy 20"-based arms for 7.15- and 7.45-meter swap bodies Note! Not suitable for 20" containers, or only possible if the container has a tunnel or opening at the front center approximately 200 mm long and 800 mm wide! Swivel frame with heavy-duty ball bearing swivel ring 2 wheel chocks with holders Aluminum side impact protection Side impact protection set inward for optimal clearance to the swap body supports Steel underrun protection Underrun protection shortened for optimal clearance to the swap body supports; lighting system mounted in a protected position Half-shell fenders Rear mud flaps across the entire width *Trailer Coupling Device (Turntable) Towing fork with certified 40 mm tow eye Spring-loaded towing fork height adjustment *Axles + Suspension SAF disc brake axles “Laser-measured axles/chassis” reduces tire wear and fuel consumption Air suspension *Brake System 2-line compressed air brake system; color-coded lines for easy servicing. Air reservoir: 208 liters Spring-loaded parking brake 2 non-reversible coupling heads at the front, with connecting lines to the tractor unit, EBS, Electronic Brake System with EBS connector at the front, with connecting cable, Caution: The trailer may only be towed by towing vehicles that ensure the effectiveness of the ABS! With lift/lower valve, hold function in both lower and lift positions *Wheels and Tires 385/65 R22.5" Manufacturer’s choice Steel rims, factory silver, ET 120 *Electrical System 24 volts, multi-chamber lights, yellow LED side lighting 2 white front position lights 2 white/red rear lane-keeping lights 2 x 7-pin reverse-proof connectors at the front, with connecting cable, 2 additional LED work lights at the rear, activated by the reverse light 1 LED work light at the front, centered between the cross members, shining toward the rear, activated by the reverse light *Country of Registration/License Plates Germany with DEKRA approval and certification (in accordance with §13 EG - FGV) 24/7 service hotline prepared for single-line license plate holder Contour marking with reflective strips per ECE R 048, white on the sides and red at the rear *Paint finish Frame Hot-dip galvanized or painted according to customer specifications Customized transport solution Configure your Fliegl vehicle to meet your requirements. The vehicle shown is an example. Production and equipment are customized according to customer specifications. Bwodpfx Aozd U Uuecfop

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 3,100 kg, maximum load weight: 14,900 kg, overall weight: 18,000 kg, axle configuration: 2 axles, total length: 9,970 mm, total width: 2,550 mm, total height: 1,250 mm, suspension: air, tire condition: 100 %, Customized Transport Solution Configure your Fliegl vehicle to meet your specific requirements. The vehicle shown is an example. Production and equipment are customized according to customer specifications. Bodpfx Aozd U I Uecfjwp *Chassis for central-axle trailer Fine-grained steel welded construction Front stop, transverse, in a foldable/adjustable design, as previously delivered with AU 257359 1 pair of removable guide rollers, front and rear 1 additional pair of removable guide rollers 4 container locks with sturdy arms based on 20" for swap bodies 7.45 m and 7.82 m 1 pair of front transmission support legs, with straight lower section and single-side operation on the right side 1 pair of rear transmission support legs, with straight lower section and single-side operation on the right side (FR) Side impact protection set inward, for optimal clearance to the swap body supports Steel underrun protection *Towing equipment for central-axle trailers Towing beam with certified 50 mm tow eye, freight forwarding version Flat flange plate for tractors with underrun-protected LBW, connected to the drawbar at the top and bottom Drawbar clamped/bolted, easily replaceable and partially adjustable in length! Under-coupler drawbar, free drawbar length approx. 2150 mm Folding bracket with spring support on the drawbar, for routing the connection cables to the truck *Axles + Suspension SAF or BPW disc brake axles “Laser-aligned axles/chassis” reduces tire wear and fuel consumption Travel odometer/odometer Air suspension *Brake System 2-line compressed air brake system Color-coded lines for easy servicing. Air reservoir: 208 liters Spring-loaded parking brake, Control panel in the front right Duomatic connection at the front, with connecting line to the tractor unit, connection in the front right 24-volt EBS, electronic braking system with EBS connector at the front, with connecting cable, connection in the front right Caution: The trailer may only be towed by towing vehicles that ensure the effectiveness of the ABS! With lift & lower valve, hold function in both lower and lift positions Vehicle – Vehicle Stability Control System Brake release function via a pushbutton on the vehicle next to the lift & lower valve, for releasing the brake when coupled; EBS power supply must be ensured! “TPMS” Tire Pressure Monitoring System according to ECE R 141, display in the towing vehicle via EBS *Wheels and Tires 385/65 R22.5" steel rims, factory silver *Electrical System 24 volts, multi-chamber LED lights, yellow LED side lights, LED license plate lights, (Note: With certain towing vehicles, false diagnostic errors may occur even though the system is functioning properly) Yellow LED side lights linked to the turn signals “Flashing side lights” Parking sockets for electrical and air connections on the drawbar 2 white LED front position lights 2 white/red LED rear lane-keeping lights 1 x 15-pin connector at the front, with connecting cable, located on the right rear 2 additional LED work lights, recessed and integrated into the rear, activated by the reverse light 1 LED work light at the front, centered between the cross members, shining toward the rear, activated by the reverse light *Country of Registration/License Plates Prepared for single-line license plate holder Night parking sign at front and rear *Paint Finish Frame Hot-dip galvanized or painted according to customer preference

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 3,230 kg, maximum load weight: 14,770 kg, overall weight: 18,000 kg, axle configuration: 2 axles, total length: 10,020 mm, total width: 2,550 mm, total height: 870 mm, suspension: air, tire size: 235/75 R17,5", tire condition: 100 %, *Wechel Central-Axle Trailer Chassis Bwodpfx Aozd Uyqjcfep Fine-grained steel welded construction Front stop, longitudinally adjustable and foldable 2 pairs of removable guide rollers, front and rear Locks height-adjustable by approx. 120 mm for parking height 1070 mm, lifting height then approx. 1150 mm, and driving height then approx. 990 mm; foldable with center supports. Includes guide rollers that can be inserted into center supports (locking mechanism from the Vario chassis at the rear) 4 container locks with sturdy arms on a 20" base for swap bodies 7.15 / 7.45 and 7.82 1 pair of front transmission support legs, with straight lower section and single-sided operation on the right rear Foldable rear support 2 wheel chocks with holder Aluminum side impact protection Steel underrun protection Half-shell fenders 1 spare wheel holder for 1 electric bike, with wheel mounting kit 1 plastic toolbox, with insert shelf, W=620/H=360/D=440 mm, lockable with a padlock. (Lock not included) *Towing equipment for central-axle trailer Towing beam with certified 50 mm tow eye, freight transport version (not suitable for trucks with tail lifts; detailed verification may still be required when placing an order) Towing beam lower coupler, free towing beam length approx. 2200 mm Folding bracket with spring support on the towing beam, for routing the connection cables to the truck *Axles + Suspension SAF drum brake axles “Laser-aligned axles/chassis” Reduces tire wear and fuel consumption Air suspension *Brake System 2-line compressed air brake system Color-coded lines for easy servicing. Spring-loaded parking brake 2 non-reversible coupling heads at the front, with connecting lines to the motor vehicle, connection at FR-right EBS, Electronic Brake System with EBS connector at the front, with connecting cable, connection at FR-right Caution: The trailer may only be towed by towing vehicles that ensure the effectiveness of the ABS! With lift/lower valve, hold function in both lower and lift positions Vehicle – Vehicle Stability System *Wheels and Tires 235/75 R17.5, brand selected by the manufacturer Steel rims in twin configuration, factory silver *Electrical System 24 volts, multi-chamber lights, yellow LED side lighting 2 white front position lights 2 white/red rear lane-keeping lights 1 x 15-pin connector at the front, with connecting cable, connection at the rear right 2 additional LED work lights at the rear, activated via the reverse light 1 LED work light at the front, centered between the cross members, shining toward the rear, activated via the reverse light *Operating Instructions The specified total weight is technically possible; however, depending on the cargo, the total weight may not be reached while complying with the permissible axle, support, and fifth-wheel loads. (Poor handling and tracking may result from improper load distribution) *Country of Registration/License Plates Germany With DEKRA approval and certification (in accordance with §13 EG-FGV) 24/7 Service Hotline Prepared for single-line license plate holders Contour markings with reflective strips in accordance with ECE R 048, white on the sides and red at the rear *Paint Finish Frame Hot-dip galvanized or painted according to customer specifications

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 3,000 kg, maximum load weight: 15,000 kg, overall weight: 18,000 kg, axle configuration: 2 axles, total length: 9,470 mm, total width: 2,550 mm, total height: 1,040 mm, suspension: air, tire size: 235/75 R17,5", tire condition: 100 %, Customized Transport Solution Configure your Fliegl vehicle to meet your specific requirements. The vehicle shown is an example. Production and equipment are customized according to customer specifications. *Chassis with swivel turntable Fine-grained steel welded construction Front stop, longitudinally adjustable and foldable 2 pairs of removable guide rollers, front and rear 1 pair of removable guide rollers, additional 4 container locks with sturdy 20"-based arms for swap bodies 7.15 and 7.45 Swivel frame with heavy-duty ball bearing swivel ring Wheel chocks with holder Aluminum side impact protection Side impact protection set inward for optimal clearance to the swap body supports Steel underrun protection Underrun protection shortened for optimal clearance to the swap body supports; lighting system mounted in a protected position Rear mud flaps across the entire width (not compatible with forklift mount) Quarter-shell front fenders and half-shell rear fenders *Towing equipment for trailer turntable Towing fork with certified 40 mm tow eye Towing fork mechanically adjustable in length by approx. 6 x 100 mm (approx. 1900–2500 mm); towing fork length set to 2200 mm *Axles + Suspension BPW or SAF drum brake axles, at the manufacturer’s discretion “Laser-aligned axles/chassis” to reduce tire wear and fuel consumption Air suspension *Brake System 2-line compressed air brake system Color-coded piping for easy maintenance. Air reservoir: 180 liters Bsdpszd Uvljfx Acfswp Spring-loaded parking brake 2 non-reversible coupling heads at the front, with connecting lines to the tractor unit, EBS, Electronic Brake System with EBS connector at the front, with connecting cable, Caution: The trailer may only be towed by tractor units that ensure the effectiveness of the ABS! With raise/lower valve, hold function in both lower and raise positions Axle load detection via EBS CAN bus signal, for display in the cab; the truck must be equipped accordingly; no truck installation (no calibrated scale) Tire pressure monitoring system *Wheels and tires 235/75 R17.5, brand selected by the manufacturer Steel rims in twin configuration, factory silver *Electrical System 24 volts, Aspöck Eco LED II multi-chamber lights, yellow LED side lighting linked to the turn signals (“flashing side lights”), LED license plate lighting, (Note: With certain towing vehicles, false diagnostics may occur even though the system is functioning properly) 2 white LED front position lights 2 white/red rear lane-keeping lights (LED) 2 x 7-pin reverse-polarity-protected connectors at the front, with connecting cable, LED work lights on both sides (activated by the reverse light) 2 additional LED work lights at the rear, activated by the reverse light 1 LED work light at the front, centered between the crossbars, shining toward the rear, activated by the reverse light *Country of Registration/License Plates Germany with DEKRA approval and certification (in accordance with §13 EG - FGV) 24/7 service hotline prepared for single-line license plate holders Contour marking with reflective strips in accordance with ECE R 048, white on the sides and red at the rear *Paint Finish Frame hot-dip galvanized or painted according to customer preference

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 3,250 kg, maximum load weight: 14,750 kg, overall weight: 18,000 kg, axle configuration: 2 axles, total length: 10,020 mm, total width: 2,550 mm, total height: 1,250 mm, suspension: air, tire size: 385/65 R22,5", tire condition: 100 %, Customized Transport Solution Configure your Fliegl vehicle to meet your specific requirements. The vehicle shown is an example. Production and equipment are customized according to customer specifications. *Chassis with central-axle trailer Fine-grained steel welded construction Front stop, longitudinally adjustable and foldable 2 pairs of removable guide rollers, front and rear Bwedjzd Udcopfx Acfjp 4 container locks with sturdy 20"-based arms for 7.15 m, 7.45 m, and 7.82 m swap bodies (Note: When used in combination with the impact guard, the guard protrudes beyond the 7.15 m swap body) 1 pair of front transmission support legs, with straight lower section and single-side operation on the right rear 1 pair of transmission support legs at the rear, with straight lower section and single-side operation on the right side 2 wheel chocks with holders Aluminum side impact protection Side impact protection set inward, for optimal clearance to the swap body supports Steel underrun protection Rear mud flaps across the entire width Half-shell fenders Mud flaps *Towing Equipment for Central-Axle Trailers Towing beam with certified 50 mm tow eye, freight carrier version Flat flange plate for tractors with a clearance-type low-bed trailer, connected to the towing beam at the top and bottom Towing beam clamped/bolted, easily replaceable, and partially adjustable in length! Lower coupler drawbar, free drawbar length approx. 2200 mm Fold-down bracket with spring assistance on the drawbar, for routing the connection cables to the truck *Axles + Suspension BPW disc brake axles “Laser-measured axles/chassis” reduces tire wear and fuel consumption Air suspension *Brake system 2-line compressed air brake system Color-coded wiring for easy servicing. Air reservoir: 208 liters Air-spring parking brake, Control panel at the rear right Duomatic connection at the front, with connecting line to the tractor unit, connection at the rear right 24-volt EBS, electronic braking system with EBS connector at the front, with connecting cable, connection at the rear right Caution: The trailer may only be towed by towing vehicles that ensure the effectiveness of the ABS! With lift and lower valve, hold function in both lower and lift positions Vehicle - Vehicle Stability Control System *Wheels and Tires 385/65 R22.5" Manufacturer's choice Steel rims, factory silver *Electrical System 24 volts, multi-chamber lights, yellow LED side lighting Connectors for electrical and air connections on the drawbar 2 white front position lights 2 white/red rear lane-keeping lights 1 x 15-pin connector at the front, with connecting cable, connection at FR-right 2 additional LED work lights, recessed and integrated into the rear, activated via the reverse light 1 LED work light at the front, centered between the cross members, shining toward the rear, activated via the reverse light *Country of Registration/License Plates Germany With DEKRA approval and certification (per §13 EG - FGV) 24/7 service hotline Prepared for single-line license plate holder Warning sign per ECE - 70 Night parking sign front and rear Contour markings with reflective strips in accordance with ECE R 048, white on the sides and red at the rear *Paint finish Frame Hot-dip galvanized or painted according to customer specifications

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 3,220 kg, maximum load weight: 14,780 kg, overall weight: 18,000 kg, axle configuration: 2 axles, total length: 10,020 mm, total width: 2,550 mm, total height: 1,070 mm, suspension: air, tire size: 445/45 R19,5", tire condition: 100 %, Customized Transport Solution Configure your Fliegl vehicle to meet your specific requirements. The vehicle shown is an example. Production and equipment are customized according to customer specifications. *Chassis for swap body with central axle trailer Fine-grained steel welded construction Front stop, longitudinally adjustable and foldable 2 pairs of removable guide rollers, front and rear Swap Guard – swap body guide, in front of and behind each container lock 4 container locks with sturdy 20"-based arms for 7.15, 7.45, and 7.82 swap bodies 1 pair of front gear support legs, with straight lower section and single-sided operation on the right side 2 wheel chocks with holders Aluminum side impact protection Steel underrun protection Rear mud flaps across the entire width (not compatible with forklift mount) 4 half-shell fenders Mud flaps Spare tire mount for 1 electric bike, with wheel mounting kit Towing equipment for central-axle trailer Towing beam with certified 50 mm tow eye, freight forwarding version (not suitable for trucks with tail lifts; detailed verification may still be required on a case-by-case basis) Towing bar coupler, free towing bar length approx. 2200 mm Folding bracket with spring assistance on the towing bar, for routing the connection cables to the truck *Axles + Suspension SAF disc brake axles “Laser-measured axles/chassis” reduces tire wear and fuel consumption Air suspension *Brake System 2-line compressed air brake system Color-coded piping for easy maintenance. Air reservoir capacity: 208 liters Spring-loaded parking brake 2 non-reversible coupling heads at the front, with connecting lines to the motor vehicle, connection at FR-right EBS, Electronic Braking System with EBS connector at the front, including connecting cable, connection at FR-right Caution: The trailer may only be towed by towing vehicles that ensure the effectiveness of the ABS! With lift/lower valve, hold function in both lower and lift positions *Wheels and Tires 445/45 R19.5", brand selected by the manufacturer Steel rims, factory silver *Electrical system 24 volts, 4 x 3-chamber lights + 1 round backup light and + 1 round rear fog light, yellow LED lighting on the sides 2 white front position lights Bedpfx Aozd Tw Iocfjwp 2 white/red rear lane-keeping lights 1 x 15-pin connector at the front, with connecting cable, connection at the rear right 2 Additional LED work light(s) at the rear, activated via the reverse light *Country of registration/license plates Germany With DEKRA approval and certification (in accordance with §13 EG-FGV) 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips per ECE R 048, white on the sides and red at the rear *Paint finish Frame Hot-dip galvanized or painted per customer request

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 3,250 kg, maximum load weight: 14,750 kg, overall weight: 18,000 kg, axle configuration: 2 axles, total length: 10,020 mm, total width: 2,550 mm, total height: 1,120 mm, suspension: air, tire size: 385/55 R22,5", tire condition: 100 %, Customized Transport Solution Configure your Fliegl vehicle to meet your specific requirements. The vehicle shown is an example. Production and equipment are customized according to customer specifications. *Chassis for central-axle swap trailers Bwsdpfx Acjzd Trrjfjp Fine-grained steel welded construction Front stop, longitudinally adjustable and foldable Pair of removable guide rollers, front and rear 4 container locks with sturdy 20"-based arms for 7.15 m, 7.45 m, and 7.82 m swap bodies (Note: When used in combination with the impact guard, the guard protrudes beyond the 7.15 m swap body) 1 pair of front gear-driven support legs, with straight lower section and single-sided operation on the right side 1 pair of rear gear-driven support legs, with straight lower section and single-sided operation on the right side Side impact protection set inward, for optimal clearance to the swap body supports Steel underrun protection Rear mud flaps across the entire width *Towing equipment for central-axle trailers Towing beam with certified 50 mm tow eye, freight forwarding version Towing beam clamped/bolted, easily replaceable and partially adjustable in length! Lower coupler on towing beam, free towing beam length approx. 2200 mm Folding bracket with spring support on the towing beam, for routing the connection cables to the truck *Axles + Suspension SAF disc brake axles “Laser-aligned axles/chassis” reduces tire wear and fuel consumption Air suspension without lift axle *Brake System 2-line compressed air brake system Color-coded lines for easy servicing. Air reservoir: 208 liters Spring-loaded parking brake Duomatic connection at the front, with connecting line to the tractor unit, connection at the rear right 24-volt EBS, electronic braking system with EBS connector at the front, with connecting cable, connection at the rear right Caution: The trailer may only be towed by towing vehicles that ensure the effectiveness of the ABS! With lift & lower valve, hold function in both lower and lift positions Vehicle – Vehicle Stability Control System Brake release function via a pushbutton on the vehicle next to the lift & lower valve, for releasing the brake while coupled; EBS power supply must be ensured! *Wheels and Tires 385/55 R22.5" Manufacturer's choice Steel rims, factory silver *Electrical System 24 volts, multi-chamber LED lights, yellow LED side lighting, LED license plate lighting, (Note: With certain towing vehicles, false diagnostics may occur even though the function is working properly) 2 white LED front position lights 2 white/red LED rear lane-keeping lights 1 x 15-pin connector at the front, with connecting cable, connection on the right rear Additional LED work light(s), recessed and integrated into the rear, activated via the reverse light LED work light at the front, centered between the cross members, shining toward the rear, activated via the reverse light *Country of Registration/License Plates Germany With DEKRA approval and certification (per §13 EG - FGV) 24/7 service hotline Prepared for single-line license plate holder Warning sign per ECE - 70 ADR warning sign at the rear, foldable Contour marking with reflective strips in accordance with ECE R 048, white on the sides and red at the rear *Paint finish Frame Hot-dip galvanized or painted according to customer specifications

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 4,200 kg, maximum load weight: 16,800 kg, overall weight: 21,000 kg, axle configuration: 2 axles, loading space length: 5,000 mm, loading space width: 2,420 mm, loading space height: 600 mm, total length: 7,200 mm, total width: 2,550 mm, total height: 1,800 mm, suspension: air, tire size: 435/50 R19,5", tire condition: 100 %, Custom-made transport solution Configure your Fliegl vehicle according to your requirements. The vehicle shown is an example. Production and equipment are tailored to individual customer requirements. Chassis, central axle, tipping trailer Steel welded construction, continuous tipping shaft at the rear with 100 mm ball bearing Type 210, then total weight technically 21,000 kg (special permit required) Gearbox support leg at the front Retractable rear support 2 chocks with holder Under-ride guard, steel Splash guards at the rear over the entire width (not in conjunction with forklift holder) Quarter panel fenders in front of and behind each axle 1 plastic toolbox, w=600 / h=425 / d=460 mm, lockable 1 pair of aluminum ramps, 3,440 mm long, 360 mm wide, load capacity per pair 8,000 kg (attachment rail for ramps at the rear) Coupling device for central axle trailer Drawbar with tested 50 mm tow hitch Axles + suspension BPW disc brake axles "Axle/chassis laser-aligned" reduces tire wear and fuel consumption Axle spacing 1810 mm (then 10 tons axle load technically) Air suspension Braking system 2-line compressed air brake system Color-coded line routing for easy maintenance. Spring brake parking brake 2 fail-safe coupling heads at the front, with connecting lines to the tractor unit, 24 Volt EBS, electronic braking system with EBS connector at the front, with connection cable, Note: The trailer may only be towed by tractor units that guarantee the effectiveness of the ABS! with lift and lower valve Vehicle - driving stability system Axle load detection via EBS-CAN bus signal, for display on the display in the driver's cab, truck must be correspondingly pre-equipped, no truck installation (no calibrated scale) Wheels and tires 435/50 R19.5", manufacturer's choice Tires with 164 K or J marking, manufacturer's choice Steel rims, factory silver Electrical system 24 Volt, multi-chamber lights, yellow LED lighting on the sides 2 white position lights at the front in LED 2 white/red marker lights at the rear 2 x 7-pole fail-safe plugs at the front, with connection cable, 1 additional LED work light at the rear, switched via reversing light Hydraulics Three-way tipping mechanism, hydraulic multi-piston press with stroke limiter and safety cable, Low-pressure cylinder up to max. 170 bar, without throttle. If required, this can be retrofitted to the truck. (Truck with max. hydraulic delivery rate of 55 l/min) Operation hydraulically via truck PTO Hydraulic connection with SVK plug NW 10/3, incl. connection hose Tipping bridges Steel sheet floor Hardox 450, 4 mm thick, ball bearing at the rear, 100 mm diameter Side panel construction steel, side walls foldable and pivotally mounted with central locking at the bottom. Rear wall pivotable and as a 2-wing door (not foldable), with door holder and protective rubber on the side (not in conjunction with pivot or mesh grating attachment) Side wall retraction springs (not possible with foldable front wall) Platform width 2420 mm 5 pairs of lashing eyes in the floor, 5 tons each Painting Side panels/bridge painted in desired color Bodpfxozd Eyno Acfjwp Custom-made transport solution Configure your Fliegl vehicle according to your requirements. The vehicle shown is an example. Production and equipment are tailored to individual customer requirements.

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 4,900 kg, maximum load weight: 34,100 kg, overall weight: 39,000 kg, axle configuration: 3 axles, loading space length: 9,300 mm, loading space width: 2,420 mm, loading space height: 2,150 mm, loading space volume: 49 m³, total length: 10,300 mm, total width: 2,550 mm, total height: 4,040 mm, suspension: air, tire size: 385/65 r22.5, tire condition: 100 %, Customized Transport Solution Configure your Fliegl vehicle according to your requirements. The vehicle shown is an example. Production and equipment are tailored to individual customer needs. Further Information Chassis Fine-grain steel welded construction, lightweight design, fifth wheel plate with interchangeable 2 kingpins Curved front end, patented 24-ton, 2-speed landing gear, single-sided operation, with straight lower part, without push-pull compensation Wedge supports + holder Under-run protection, foldable Semi-shell fenders Integrated fender holder, surface repels stones Towing hook at the rear Axles + Suspension SAF disc brake axles Axle/suspension laser-aligned, reduces tire wear and fuel consumption Air suspension 1st axle: automatic lift axle, including forced lowering and starting assist, activated by 3x braking (starting assist functional up to an axle load exceeding 30% and a speed of max. 25 km/h) Hot-dip galvanized lift axle mechanism, 10-year warranty against rust-through Braking System 2-line pneumatic braking system, color-coded lines for easy servicing Spring-loaded parking brake 2 non-interchangeable coupling heads at the front, without connecting line EBS, electronic braking system with EBS socket at the front, without connection cable Note: The trailer may only be pulled by tractor units that ensure the effectiveness of the ABS! With lifting and lowering valve Vehicle - Driving Stability System Wheels & Tires 385/65R22.5, manufacturer's choice Polished aluminum rim, manufacturer's choice Electrical System 24 Volt, multi-chamber lights, yellow LED lighting on the sides 2 white position lights at the front 2 white/red marker lights at the rear 2 x 7-pin socket at the front, without connection cable Hydraulics Low-pressure cylinder, max. 170 bar, smallest stage hard-chromed, with HDK screw-on fitting, fixed part, NW 48 mm Actuation hydraulically via truck auxiliary drive Tippers Aluminum box tipper, sloping front wall, 5 mm thick, with external side walls made of 30 mm hollow profile, cleanly welded, with upper edge profile that prevents spillage of bulk goods. Interior with access ladder on the front wall Shovel and broom holder on the outside of the front wall Greenline - conical and aerodynamic tipper body shape Membrane - rear wall Rear wall as a swing-open flap with double-joint hinge, externally mounted with 2-fold hook locking. Rear wall with rubber seal Note! Heat-resistant up to max. 170°C! Floor continuously 5 mm thick, Brinell 110 Note! Only for the transport of sand, gravel and rolled gravel with a maximum grain size of up to 20 mm! All other transported goods are excluded from the warranty! Standing platform with access ladder, connecting plate for air/electricity and brake with large space for the best possible operation. Roll tarp, single-sided for storing on the right-hand side (when facing forward), with central locking on the left-hand side (when facing forward) Bwedpfxoi Ri Ids Acfep Operating instructions For the transport of salt, lime, etc., we recommend a tipping cylinder with a hard-chromed piston rod to protect against rust The specified total weight is technically possible, but depending on the cargo, the total weight may not be reached while complying with the permissible axle/support and saddle loads. (Poor driving and handling behavior possible due to incorrect load distribution) Country of registration / Signs Germany with Dekra approval and certificate (according to §13 EG - FGV) 24/7 service hotline pre

Condition: new, machine/vehicle number: Produktpalette, empty load weight: 5,600 kg, maximum load weight: 33,400 kg, overall weight: 39,000 kg, axle configuration: 3 axles, loading space length: 9,200 mm, loading space width: 2,420 mm, loading space height: 2,150 mm, loading space volume: 50 m³, total length: 10,300 mm, total width: 2,550 mm, total height: 4,040 mm, suspension: air, tire size: 385/65 R 22,5, tire condition: 100 %, Customized Transport Solution Configure your Fliegl vehicle according to your requirements. The vehicle shown is an example. Production and equipment are customized according to customer specifications. Further Information Chassis, Semi-Trailer, Tipper Fine-grained steel welded construction, in basic lightweight design, turntable with interchangeable 2 kingpin Curved front end, patented 24 tons, 2-speed landing gear, single-sided operation, with straight lower part, without stroke compensation 2 support wedges with holder Underrun protection, foldable Half-shell fenders Integrated fender holder, surface designed to repel stones With anti-splash flaps, only on the last axle 1 tarpaulin rod with bracket 2 towing hooks at the rear Axles + Suspension BPW disc brake axles with 430 mm disc diameter Bwedpfx Asi Ri Ihecfep Axle/chassis laser-aligned to reduce tire wear and fuel consumption Air suspension 1st axle, automatic lift axle, including forced lowering and starting aid Hot-dip galvanized lift axle mechanism, 10-year warranty against rust-through Braking System 2-line compressed air braking system, color-coded lines for easy servicing Spring brake parking brake 2 tamper-proof coupling heads at the front, without connection line EBS, Electronic Braking System with EBS socket at the front, without connection cable Note: The trailer may only be pulled by tractor units that guarantee the effectiveness of the ABS! With lifting and lowering valve Vehicle – Driving Stability System Wheels and Tires 385/65 R22.5, manufacturer’s choice Steel rims, factory silver "TPMS" Tire Pressure Monitoring System according to ECE R 141, display via the tractor unit’s display, via EBS, without installation in the truck (this must be available in the truck. Only on base tires). Electrical System 24 Volt, multi-chamber lights, yellow LED lighting on the sides Yellow LED lighting on the sides linked to the turn signal "flashing side lights" 2 white position lights at the front 2 white/red outline lights at the rear 2 x 7-pin tamper-proof sockets at the front, without connection cable Hydraulics Low-pressure cylinder max. 170 bar, smallest stage hard-chromed, with HDK screw sleeve, fixed part, NW 48 mm (without hose connection) Operated hydraulically via truck auxiliary drive Tipping Body Aluminum box tipper body made of high-quality, abrasion-resistant material, front wall 5 mm thick, with outer wall made of 30 mm hollow chamber profiles, neatly welded, with top edge profile that prevents material from spilling out. Inside with access ladder on the front wall (not in connection with Cramaro). Shovel and broom holder on the outside of the front wall. Greenline – tapered and aerodynamic tipper body design Membrane – rear wall Rear wall with double-joint hinge, mounted to allow movement, with 2-part door division 1/2 to 1/2, at the top with a pivoting gantry, with one grain slide per door. Rear wall with rubber seal. Note! Heat resistant up to max. 170°C! Floor consistently 6 mm thick Standing platform with access ladder, connection plate for air/electrical and brake with large clearance for best possible operation. Roller cover, single-sided for depositing on the right-hand side, with central locking on the left-hand side Approval Country/Signage Germany Type approval according to EC 2007/46 24/7 service hotline Prepared for single-row license plate holder Contour marking with reflective strips according to ECE R 048, white on the sides and red at the rear Painting Frame DB 7350 Novagra

Condition: new, machine/vehicle number: Produktpalette, empty load weight: 3,950 kg, maximum load weight: 31,050 kg, overall weight: 35,000 kg, axle configuration: 3 axles, loading space length: 7,200 mm, loading space width: 2,420 mm, loading space height: 1,450 mm, loading space volume: 25 m³, total length: 8,600 mm, total width: 2,550 mm, total height: 2,930 mm, suspension: air, tire size: 385/65r22.5, tire condition: 100 %, Customized transport solution Configure your Fliegl vehicle according to your requirements. The vehicle shown is an example. Production and equipment are tailored to individual customer requirements. More information: Chassis Fine-grained steel welded construction, lightweight design, kingpin plate with 2 interchangeable kingpins Curved front end, patented Telescopic support in the center, cannot be uncoupled with load, in the uncoupled state, the vehicle must stand at an angle towards the rear. 2 chock blocks + holder Underrun protection, foldable Semi-shell fenders Integrated fender holder, surface repels stones with anti-splash flaps on the last axle 1 tarpaulin rod + holder 2 towing hooks at the rear Axles + suspension SAF disc brake axles with 430 mm disc diameter Axle/suspension laser-aligned to reduce tire wear and fuel consumption Axles in off-road design Air suspension 1st axle automatic lift axle, incl. forced lowering and start-up assist, operated 3x by braking (start-up assist functional up to an axle load exceedance of 30% and a speed of max. 25 km/h) Hot-dip galvanized lift axle mechanism Braking system 2-line pneumatic braking system, color-coded lines for easy servicing Spring-loaded parking brake 2 non-interchangeable coupling heads at the front, without connection line EBS, electronic braking system with EBS socket at the front, without connection cable Attention: Trailer may only be pulled by towing vehicles that guarantee the effectiveness of ABS! with lifting and lowering valve Vehicle driving stability system Automatic tilting lowering with shut-off valve Wheels & tires 385/65R22.5, manufacturer's choice Bwedpfxei Ri R Ie Acfjp Steel rims, factory silver Electrical system 24 Volt multi-chamber lights, yellow LED lighting on the side 2 white position lights at the front 2 white/red marker lights at the rear 2 x 7-pole non-interchangeable sockets at the front, without connection cable Hydraulics Low-pressure cylinder max. 170 bar, smallest stage hard-chromed, with HDK screw fitting, fixed part NW 48 mm. Actuation via truck auxiliary drive Tipping body Aluminum box body, sloping front wall 5 mm thick, 30 mm hollow chamber profiles, cleanly welded, with top rail profile that prevents bulk material from spilling. Inside with ladder on the front wall. Shovel and broom holder on the outside of the front wall. Greenline - conical and aerodynamic tipping body shape Membrane - rear wall Rear wall as a hinged flap with double hinge, externally mounted with a double hook lock. Rear wall with rubber seal. Note! Heat resistant up to max. 170°C! Floor continuously 6 mm thick Standing platform with ladder, connecting plate for air/electricity and brake with large clearance for best possible operation. Roller cover on one side for storage on the right, with central locking on the left. Operating instructions For the transport of salt, lime, etc., we recommend a tipping cylinder with a hard-chromed piston rod, so that it is not attacked by the material and does not rust. The stated total weight is technically possible, but depending on the load, the total weight may not be reached while observing the permissible axle/support and kingpin loads. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of approval/signage Germany Type approval according to EC 2007/46 24/7 service hotline prepared for license plate holder, single row Contour marking with reflective tape according to ECE R 048, white on the sides and red at the

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 3,980 kg, overall weight: 35,000 kg, axle configuration: 3 axles, loading space width: 2,420 mm, loading space height: 1,450 mm, loading space volume: 25 m³, total length: 8,600 mm, total width: 2,550 mm, total height: 3,240 mm, suspension: air, tire size: 385/65 r22.5, tire condition: 100 %, Customized transport solution Configure your Fliegl vehicle according to your requirements. The vehicle shown is an example. Production and equipment are tailored to individual customer needs. More information Chassis Fine-grained steel welded construction, lightweight design, kingpin plate with 2 interchangeable kingpins Curved front end, patented without support leg Wheel chocks + holder Underrun protection, foldable Semi-shell fenders integrated fender holder, surface resistant to stone chipping Towing hook at the rear Axles + Suspension SAF disc brake axles Axle/chassis laser-measured to reduce tire wear and fuel consumption Air suspension 1st axle automatic lift axle, incl. forced lowering and starting assist, actuated by 3x brakes (starting assist functional up to an axle load exceedance of 30% and a speed of max. 25 km/h) Hot-dip galvanized lift axle mechanism Braking system 2-line compressed air braking system, color-coded lines for easy servicing Spring-loaded parking brake 2 tamper-proof coupling heads at the front, without connecting line EBS, electronic braking system with EBS socket at the front, without connecting cable with lifting and lowering valve Vehicle driving stability system Wheels & tires 385/65 R22.5, manufacturer's choice Polished aluminum rim, manufacturer's choice Electrical system 24 Volt, multi-chamber lights, yellow LED lighting on the sides 2 white position lights at the front 2 white/red side marker lights at the rear 2 x 7-pin socket at the front, without connecting cable Hydraulics Low-pressure cylinder max. 170 bar, smallest stage hard chrome plated, with HDK screw connection, fixed part, NW 48 mm. Actuation via hydraulic system connected to the truck's auxiliary drive Tippers Sloping front wall 5 mm thick, with external side walls made of 30 mm hollow chamber profiles, neatly welded, with upper edge profile to prevent material spillage. Inside with a ladder on the front wall Shovel and broom holder on the outside of the front wall Greenline - conical and aerodynamic tipper body shape Membrane - rear wall Rear wall as a hinged flap with double-joint hinge, externally supported with a double hook lock. Rear wall with rubber seal Note! Heat resistant up to max. 170°C! Floor continuously 5 mm thick, Brinell 110 Note! Only for the transport of sand, gravel and rolled gravel with max. grain size up to 20 mm! All other transport goods are excluded from the warranty! Standing platform with ladder, connection plate for air/electric and brake with large clearance for best possible operation. Rollover tarpaulin, one-sided for laying down on the right-hand side, with central locking on the left-hand side Operating instructions For the transport of salt, lime, etc., we recommend a tipping cylinder with a hard-chrome plated piston rod to protect against rust The specified total weight is technically possible, depending on the cargo, the total weight may not be reached while observing the permissible axle/support and saddle loads. (Poor driving and handling behavior due to incorrect load distribution possible) Country of approval/ Signage Germany with Dekra approval and certificate (according to §13 EG - FGV) 24/7 service hotline prepared for single-line license plate holder Contour marking with reflective strips according to ECE R 048, white on the sides and red at the rear Paintwork Frame DB 7350 Novagrau Bwsdpfx Acsi Ri H Ssfjp Tipper body R

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 4,350 kg, maximum load weight: 28,650 kg, overall weight: 33,000 kg, axle configuration: 2 axles, loading space length: 7,200 mm, loading space width: 2,420 mm, loading space height: 1,750 mm, loading space volume: 30 m³, total length: 8,600 mm, total width: 2,550 mm, total height: 3,400 mm, suspension: air, tire size: 385/65R22,5, tire condition: 100 %, Customized transport solution Configure your Fliegl vehicle according to your requirements. The vehicle shown is an example. Production and equipment are carried out individually according to customer requirements. Further information Chassis, semi-trailer, tipper Fine-grained steel welded construction, lightweight design, fifth wheel with 2 interchangeable kingpins Curved front panel, patented 24 tons, 2-speed landing gear, single-sided operation, with straight lower part, without slide-out compensation 2 support wedges with holder Underrun protection, foldable Half-shell fenders Tarp pole with bracket 2 towing hooks at the rear Axles + suspension SAF disc brake axles with 430 mm disc diameter Axle/chassis laser-aligned, reducing tire wear and fuel consumption Axles in off-road design Air suspension 1st axle, automatic lift axle, including forced lowering and starting assist Hot-dip galvanized lift axle mechanism, 10-year warranty against rust-through Brake system 2-line compressed air brake system, colored line routing for easy servicing Spring-loaded parking brake 2 non-interchangeable coupling heads at the front, without connecting line EBS, electronic brake system with EBS socket at the front, without connecting cable Note: The trailer may only be pulled by towing vehicles that guarantee the effectiveness of the ABS! with lifting and lowering valve Vehicle - driving stability system Wheels and tires 385/65 R22.5, manufacturer's choice Steel rims, factory silver "TPMS" tire pressure monitoring system according to ECE R 141, display via the towing vehicle's display, via EBS, without installation in the truck (this must be available in the truck. Only on the base tires). Electrical system 24 volts, multi-chamber lights, yellow LED lighting on the side Yellow LED lighting on the side linked to the turn signal "flashing side marker lights" 2 white position lights at the front 2 white/red side marker lights at the rear 2 x 7-pole non-interchangeable sockets at the front, without connecting cable Hydraulics Low-pressure cylinder max. 170 bar, smallest stage hard-chrome plated, with HDK screw connection, fixed part, NW 48 mm (without hose connection) Operation hydraulically via truck auxiliary drive Tippers Aluminum box tipper made of high-quality, abrasion-resistant material, front wall 5 mm thick, with external side walls made of 30 mm hollow chamber profiles, cleanly welded, with a top profile that prevents bulk materials from shifting. Inside with a ladder on the front wall (not in connection with Cramaro). Shovel and broom holder on the outside of the front wall. Greenline - conical and aerodynamic tipper body shape Diaphragm - rear wall Rear wall as a swing gate with double hinge, externally mounted with double hook locking. Rear wall with rubber seal. Note! Heat-resistant up to max. 170°C! Floor continuously 6 mm thick Standing platform with ladder, connection plate for air/electricity and brake with large clearance for best possible operation. Roll-up cover on one side to be placed on the right, with central locking on the left Country of registration/Signs Germany with Dekra approval and certificate (according to §13 EC - FGV) 24/7 service hotline prepared for single-row license plate holder Contour marking with reflective strips according to ECE R 048, white on the side and red at the rear Paintwork Bwodsi Riziopfx Acfop Frame DB 7350 Novagrau "10-year warranty against rust-through" Tipper body RAL optional, solid color Roll-up cover RAL 7035 light g

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 5,350 kg, maximum load weight: 33,650 kg, overall weight: 39,000 kg, axle configuration: 3 axles, loading space length: 7,200 mm, loading space width: 2,350 mm, loading space height: 1,650 mm, loading space volume: 25 m³, total length: 8,600 mm, total width: 2,550 mm, total height: 3,000 mm, suspension: air, tire size: 385/65 R 22.5, tire condition: 100 %, Customized transport solution Configure your Fliegl vehicle according to your requirements. The vehicle shown is an example. Production and equipment are tailored to individual customer needs. Further information: Chassis, semi-trailer tipper Fine-grained steel welded construction, in basic lightweight design, trailer plate with 2 interchangeable kingpins Curved front end, patented Telescopic support in the center, uncoupling with load is not possible; when uncoupled, the vehicle must be tilted backwards. Bwsdpfxji Ri Dpe Acfsp Wedge blocks with holder Rear underrun protection, foldable Half-shell fenders Integrated fender holder, surface repels stones Tarpaulin rod with holder Towing hook at the rear Axles + Suspension SAF disc brake axles with 430 mm disc diameter Axle/chassis laser-aligned, reduces tire wear and fuel consumption Axles in off-road design Air suspension 1st axle: automatic lift axle, including forced lowering and starting assistance Hot-dip galvanized lift axle mechanism, 10-year warranty against rust-through Braking system 2-line compressed air braking system, color-coded lines for easy servicing Spring-loaded parking brake 2 non-interchangeable coupling heads at the front, without connecting line EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be pulled by towing vehicles that ensure the effectiveness of the ABS! with lifting and lowering valve Vehicle - driving stability system Wheels and tires 385/65 R22.5 Steel rims, factory silver "TPMS" tire pressure monitoring system according to ECE R 141, display on the towing vehicle's display, via EBS, without installation in the truck (this must be available in the truck). Only on standard tires. Electrical system 24 Volt, multi-chamber lights, yellow LED lighting on the sides Yellow LED lighting on the sides linked to the turn signal ("flashing side lights") 2 x 7-pole non-interchangeable sockets at the front, without connecting cable Hydraulics Low-pressure cylinder, max. 170 bar, smallest stage hard-chromed, with HDK screw coupling, fixed part, NW 48 mm (without hose connection) Operation hydraulically via truck auxiliary drive Body Steel round body in Stone Master design made of highly wear-resistant HB 400/450 steel. Sloping front wall with externally mounted hydraulic cylinders with access ladder on the front wall. Greenline - conical and aerodynamic body shape Shovel and broom holder on the outside of the front wall. Membrane - rear wall Rear wall as a hinged flap with double-hinge hinge, externally mounted with double hook lock. 2 clamping screws with lever locks on the lower side. Side walls continuous, 4 mm thick, floor 4/5 mm thick, wear-resistant and weight-optimized design Standing platform with access ladder, connection plate for air/electricity and brake with large clearance for best possible operation. Roller cover on one side for placement on the right side, with central locking on the left side Country of registration / signs Germany Type approval according to EC 2007/46 Superstructure strength according to EN 12642 24/7 service hotline prepared for single-row license plate holder Warning sign according to ECE - 70 Contour marking with reflective strips according to ECE R 048, white on the sides and red at the rear Paint finish Frame DB 7350 Novagrau "10-year warranty against rust-through" Support legs galvanized Body RAL desired color, solid color Roller cover RAL 7035 light gray

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 5,400 kg, maximum load weight: 33,600 kg, overall weight: 39,000 kg, axle configuration: 3 axles, loading space length: 7,200 mm, loading space width: 2,350 mm, loading space height: 1,450 mm, loading space volume: 25 m³, total length: 8,600 mm, total width: 2,550 mm, total height: 2,960 mm, suspension: air, tire size: 385/65 R22.5", tire condition: 100 %, Customized Transport Solution Configure your Fliegl vehicle according to your individual requirements. The vehicle shown is an example configuration. Production and equipment are tailored to customer specifications. ## Chassis * High-tensile fine-grain steel welded lightweight construction * Fifth wheel plate with replaceable 2” king pin * Patented curved front end design * Parking in loaded condition not permitted; when unhooked, the vehicle must be positioned with a rearward tilt * Foldable underrun protection * Integrated mudguard mounting system with stone-repellent surface * Asphalt specification spray flaps behind last axle, hinged to mudguards with upper locking option; shortened mudguards ## Axles & Suspension * Disc brake axles with 430 mm brake discs * Laser-aligned axles and running gear for reduced tyre wear and fuel consumption * Off-road axle specification * Air suspension system * 1st axle as automatic lifting axle with forced lowering and traction aid * Galvanised lifting axle mechanism ## Braking System * Dual-line compressed air braking system with colour-coded piping for simplified maintenance * Spring-loaded parking brake * Two non-interchangeable coupling heads at the front (without connecting lines) * 24 V EBS electronic braking system with front EBS socket (without connecting cable) * Raise-and-lower valve integrated * Vehicle stability control system ## Wheels & Tyres * 385/65 R 22.5 tyres * Steel rims, factory silver finish * TPMS (Tyre Pressure Monitoring System) according to ECE R141, displayed via truck EBS system ## Electrical System * 24 V electrical system * LED multi-chamber rear lights * Yellow LED side marker lights linked to indicators (flashing side marker lights) * 2 white LED front position lights * 2 white/red LED rear outline marker lights * 2 × 7-pin front sockets ## Hydraulic System * High-pressure tipping cylinder, max. 250 bar * HDK screw coupling, fixed section, NW 48 mm * Hydraulic operation via truck PTO (power take-off) ## Tipping Body – Stone Master Thermo Body * Round steel body in “Stone Master Design” made of high wear-resistant HB 400/450 steel * Sloped front wall with external hydraulic cylinder mounting * Front wall access ladder included * “Membrane” tailgate design: externally mounted pendulum rear door with double hook locking system * Two clamping screws with lever fasteners on lower side * Side walls: 4 mm continuous steel Bedpfxsi Rix Ij Acfjwp * Floor: 4–5 mm steel, wear- and weight-optimised construction * Fully insulated Fliegl Asphalt Profi Thermo body * Insulation on front, sides, bottom and rear (Fliegl Isotherm system) * BASIC cover system with tarpaulin enclosure * Standing platform with access steps * Connection panel for air, electrics and braking system with large free working space for optimal handling * Sliding tarpaulin system, one-sided storage on RHS (right-hand side), with central locking on LHS (left-hand side) ## Registration & Compliance * Germany * EC type approval according to 2007/46/EC * Body strength certification according to EN 12642 * 24/7 service hotline * Manufacturer certification for thermal vehicles according to RS 10 – 2013 * Prepared for single-line licence plate holder * Warning plate according to ECE R70 ## Optional Thermo Insulation Packages * BASICplus: sheet metal cladding * PREMIUM: stainless steel cladding

Condition: new, machine/vehicle number: Produktpalette, empty load weight: 5,700 kg, maximum load weight: 33,300 kg, overall weight: 39,000 kg, axle configuration: 3 axles, loading space length: 7,700 mm, loading space width: 2,350 mm, loading space height: 1,600 mm, loading space volume: 31 m³, total length: 9,090 mm, total width: 2,550 mm, total height: 3,110 mm, suspension: air, tire size: 385/65 R 22,5, tire condition: 100 %, Customized Transport Solution Configure your Fliegl vehicle according to your requirements. The vehicle shown is an example. Production and equipment are tailored to individual customer needs. More information Chassis, saddle, and tipper Fine-grained steel welded construction, in basic lightweight design, saddle plate with interchangeable 2 king pin Curved front panel, patented 24 tons, 2-stage support winch, single-sided operation, with straight lower part, without extension compensation Chocks with holder Bsdpfei Rivdex Acfewp Rear underrun protection, foldable Semi-shell mudguards Integrated mudguard holder, surface designed to repel stones With anti-splash flaps, only on the last axle Tarpaulin rod with holder Towing hook at the rear Axles + Suspension BPW disc brake axles with 430 mm disc diameter Axle/suspension laser-aligned, reduces tire wear and fuel consumption Air suspension 1st axle: automatic lift axle, including forced lowering and starting aid Hot-dip galvanized lift axle mechanism, 10-year warranty against rust-through Brake system 2-line compressed air brake system, color-coded lines for easy service Spring-loaded parking brake 2 fail-safe coupling heads in the front, without connection line EBS, electronic brake system with EBS socket in the front, without connection cable Note: The trailer may only be pulled by towing vehicles that guarantee the effectiveness of the ABS! With lifting and lowering valve Vehicle - driving stability system Wheels and tires 385/65 R22.5 Steel rims, factory silver "TPMS" Tire Pressure Monitoring System according to ECE R 141, display via display in the towing vehicle, via EBS, without truck installation (this must be available in the truck. Only on standard tires). Electrical system 24 Volt, multi-chamber lights, yellow LED lighting on the sides Yellow LED lighting on the sides, linked to the turn signal ("flashing side lights") 2 x 7-pole fail-safe sockets in the front, without connection cable Hydraulics Low-pressure cylinder, max. 170 bar, smallest stage hard-chromed, with HDK screw sleeve, fixed part, NW 48 mm (without hose connection) Operation hydraulically via truck auxiliary drive Dump body Steel round dump body in "Stone Master Design" made of highly wear-resistant HB 400/450 steel. Sloping front wall with external hydraulic cylinder mount. Inside with access ladder on the front wall. Greenline - conical and aerodynamic dump body shape Shovel and broom holder on the outside of the front wall Membrane - rear wall Rear wall as a pivoting flap with double-hinge hinge, externally mounted with double hook lock. 2 clamping screws with toggle closures on the lower side. Side walls continuously 4 mm thick, floor 4/5 mm thick, wear-resistant and weight-optimized construction Standing platform with access ladder, connection plate for air/electrical and brake connections with ample space for the best possible operation. Rollover cover on one side for storage on the right-hand side, with central locking on the left-hand side Country of registration/plates Germany Type approval according to EC 2007/46 Superstructure strength according to EN 12642 24/7 service hotline Prepared for license plate holder, single-line Warning sign according to ECE - 70 Contour marking with reflective strips according to ECE R 048, white on the sides and red at the rear Paint finish Frame DB 7350 Novagrau "10-year warranty against rust-through" Support legs, black coated Dump body, RAL color of your choice, single color Rollover cover,

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 3,650 kg, maximum load weight: 9,850 kg, overall weight: 13,500 kg, axle configuration: 2 axles, loading space length: 5,000 mm, loading space width: 2,420 mm, loading space height: 450 mm, total length: 6,900 mm, total width: 2,550 mm, total height: 1,680 mm, suspension: steel, tire size: 285/70 R19,5", tire condition: 100 %, Customized Transport Solution Configure your Fliegl vehicle to meet your specific requirements. The vehicle shown is an example. Production and equipment are customized according to customer specifications. Central-Axle Tipping Trailer Chassis Welded steel construction, continuous tipping shaft at the rear with 80 mm ball-type tipping bearing Front transmission support leg Foldable rear support 2 wheel chocks with holders Steel underrun protection Rear mud flaps across the entire width Quarter-shell fenders Lockable storage compartment for ramps beneath the loading area 1 plastic toolbox, with insert shelf, W=620/H=360/D=440 mm, lockable with a padlock Note! The side panel touches the storage compartment when folded down. Lockable storage compartment for ramps beneath the cargo area Towing Equipment for Central-Axle Trailers Towing beam with certified 40 mm tow eye Bwedpfxszd D Sce Acfop Towing beam height-adjustable via spindle, max. adjustment range 300 mm Axles + Suspension SAF drum brake axles “Laser-measured axles/chassis” reduces tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber mounts and mechanical axle load compensation (rocker compensation) Wheels and Tires 285 / 70 R 19.5" as selected by the manufacturer Steel rims in factory silver Braking System 2-line compressed air braking system Spring-loaded parking brake 2 non-reversible coupling heads at the front, with connecting lines to the tractor unit, ABS and ALB, with ABS connector at the front, with connecting cable Caution: The trailer may only be towed by towing vehicles that ensure the effectiveness of the ABS! Electrical System 24 volts, multi-chamber lights, yellow LED side lighting 2 white front position lights 2 white/red rear lane-keeping lights 2 x 7-pin reverse-polarity-protected connectors at the front, with connecting cable Hydraulics Three-way tipping mechanism, hydraulic multi-piston press with stroke limiter and safety cable, low-pressure cylinder up to 170 bar max., without throttle valve. If necessary, this must be retrofitted to the truck. Hydraulic operation via truck PTO Hydraulic connection with SVK coupler, size 10/3, including connecting hose Tipping platforms Sturdy tipping platform with 4 mm steel plate floor, steel sidewall structure, continuous sidewalls that are fold-down and pivot-mounted with a central lock at the bottom. Rear corner stanchions are plug-in type. Rear wall folds down and is mounted on swing bearings, with a central lock at the bottom. Bed length approx. 5,000 mm; side walls with 6 hinges at the bottom. Sidewall retraction springs Bed width 2,420 mm 5 pairs of lashing eyes in the floor, 5 to each Operating Instructions The specified gross weight is technically possible; however, depending on the cargo, the gross weight may not be achieved while complying with the permissible axle, support, and fifth-wheel loads Country of Registration/Plates Country of registration: Germany With DEKRA approval and certification (pursuant to §13 EG-FGV) 24/7 Service Hotline Prepared for single-line license plate holder Contour marking with reflective strips per ECE R 048, white on the sides and red at the rear Paint finish Frame Hot-dip galvanized, including passivation “15-year warranty against through-corrosion” Sidewall/deck Painted in the color of your choice

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 6,100 kg, maximum load weight: 14,900 kg, overall weight: 21,000 kg, axle configuration: 1 axle, loading space length: 9,930 mm, loading space width: 2,540 mm, loading space height: 850 mm, total length: 13,680 mm, total width: 2,550 mm, suspension: air, tire size: 235/75 R17,5", tire condition: 100 %, Customized transport solution (vehicle shown is for illustrative purposes only). Production and equipment tailored to individual customer requirements. Bwjdpsi Ri Hkjfx Acfep Further information: Chassis: Low-bed semi-trailer Steel welded construction, kingpin plate with 2 replaceable kingpins, low-bed design with a sloping section from the wheel area to the gooseneck, approximately 210 mm loading height, sloping section at the rear up to the wheel area, mounting rail for aluminum ramps at the rear across the entire width. Chocks + holder Aluminum side impact protection Wheel arch with galvanized steel sheet, removable 1 towing eye at the rear, 10 tons. Spare wheel + bracket on the front bulkhead/storage box on the outside Steel storage box on the gooseneck, transversely at the front, approx.: L = 2400 mm, W = 400 mm, H = 600 mm, lockable Electric winch, 24 volts, pulling force 8165 kg, mounted at the front on the gooseneck behind the storage box, standing on the loading area, operated with a wireless remote control, cable length 35 m x approx. 10 mm, with roller cable guide and 2 removable guide rollers on the gooseneck and rear sloping section. NATO socket on the connection plate 1 pair of wheel recesses, approx. 700 mm, starting at the gooseneck, recessed into the floor, open to the outside. Note: Main frame protrudes approx. 145 mm. 4 pairs of attachment points for wheel stops (Fliegl standard), without wheel stops for parking the semi-trailer, approx. 100 mm high and approx. 100 mm long. Individual wheel stops When transporting SZM (special transport modules), an approx. 50 mm spacer is used in the front wheel recesses, creating a wheel recess approx. 50 mm high, approx. 1200 mm long, approx. 500 mm wide. Tie-down points, low-bed trailer 2 pairs of 2.5-ton tie-down points on the gooseneck. 7 pairs of tie-down eyes recessed in the top and side of the outer frame, each with 10 tons. 4 pairs of 10-ton tie-down points recessed in the top of the main frame longitudinal beam. 1 screw tie-down point with 6.7 tons each (JDT) at the rear in the center of the ramp storage compartment. 1 folding tie-down point additionally at the front in the low-bed area, each with 10 tons. Axle + suspension SAF drum brake axle Air suspension with raise and lower valve Wheels and tires 235/75R17.5 from leading manufacturers Steel rims in twin arrangement, factory silver Braking system 2-line pneumatic braking system Spring brake parking brake 2 fail-safe coupling heads at the front, without connecting line EBS, Electronic Braking System with EBS socket at the front, without connection cable Caution: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrical system 24 volts, multi-chamber lights in LED with resistor, yellow LED lighting on the sides, license plate lighting in LED, 2 white position lights at the front in LED 2 white/red marker lights at the rear in LED 2 x 7-pole and 1 x 15-pole fail-safe sockets at the front, without connection cable LED rotating beacon + holder, switched on via parking lights Additional LED work light, at the rear, switched on via reversing light Floor Gooseneck with steel/diamond plate Low-bed area: steel perforated sheet, in the wheel arch area steel/diamond plate surface, and in the wheel well area removable sheet metal Rear sloping section with steel perforated sheet Side walls Aluminum, 400 mm high, on the sides on the gooseneck, plug-in, approx. 2500 mm long Rear wall: aluminum, 400 mm high, on

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 12,800 kg, maximum load weight: 44,200 kg, overall weight: 57,000 kg, axle configuration: > 3 axles, suspension: air, tire size: 235/75 R17,5", tire condition: 100 %, Customized Transport Solution Configure your Fliegl vehicle according to your requirements. The vehicle shown is an example. Production and equipment are individually tailored to customer specifications. Chassis, Low-bed Semi-trailer Steel welded construction, drawbar plate with interchangeable 2 kingpin and 2 kingpin positions 24 tons, 2-speed landing gear, one-sided operation Foldable rear support 2 chock blocks with holder Aluminum side guard 1 plastic toolbox, with insert tray, w=620/h=360/d=440 mm, lockable with a padlock Extendable widening sections to 3,000 mm Storage compartment for timber planks on gooseneck, transverse at the front Timber planks 70 mm for widening to 3,000 mm Telescoping Central tube frame in cleanly welded, interlocking telescoping frame sections. Extendable by a maximum of 6,000 mm and lockable approximately every 1,000 mm Locking with mechanical pin lock With sliding platform Tie-down eyes, low-bed 2 pairs of ring-type tie-down eyes, each 5 tons, at the front on the gooseneck; 11 pairs of tie-down loops embedded at the top and side in the outer frame, each 10 tons; 2 on the gooseneck, 9 distributed in the low-bed area; first tie-down eye 250 mm from the front and last at most 250 mm from the rear, spacing of tie-down eyes not greater than 1,100 mm 8 pairs of socket pockets embedded in the outer frame, inner dimensions 70 x 40 mm, (can be converted to 5-ton ring-type tie-down eyes, not included in the scope of supply) 3 pairs of folding tie-down eyes additionally embedded in the low-bed area, each 10 tons; 1 at the front of the low-bed, 1 in front of the 1st axle, and 1 behind the 3rd axle Axles + Suspension SAF drum brake axles Axle/chassis laser-measured, reducing tire wear and fuel consumption Last 2 axles steerable, with automatic reverse locking via reversing light and manual locking function via a button on the vehicle Air suspension with lift and lower valve Wheels and Tires 235 / 75 R 17.5, manufacturer Fulda Steel rims in twin configuration, factory silver Braking System 2-line compressed air braking system Spring-loaded parking brake Vehicle - Driving Stability System Axle load detection via EBS-CAN bus signal, for display on the display in the driver's cab; truck must be appropriately prepared; no truck installation (no calibrated scale) 2 non-interchangeable coupling heads at the front, without connecting line EBS, electronic brake system with EBS socket at the front, without connecting cable Caution: The trailer may only be towed by towing vehicles that ensure the effectiveness of the ABS! Electrical System Bwodpoi Ri Hnefx Acfep 24 Volt, multi-chamber lights, yellow LED lighting on the sides 2 white position lights at the front 2 white/red marker lights at the rear 1 LED revolving beacon with holder, switched via parking lights (beacon removable) 2 pairs of warning panels, double LED-lit and extendable to 3,000 mm 2 x 7-pole non-interchangeable sockets at the front, without connecting cable Floor Gooseneck with steel / chequered plate surface Storage box embedded in the ramp to the gooseneck Then with 70 mm soft wood floor, steel/chequered plate surface in the wheel arch area Rear slope with 70 mm soft wood floor Side Walls 25 mm aluminum hollow profile, 400 mm high, at the front and side on the gooseneck, pluggable Ramps Steel ramps, 2,800 mm long, 750 mm wide, laterally movable Covered with wood Hydraulically operated via tractor PTO with flow control Hydraulic connection with SVK coupling NW 10/3, without connect

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 4,750 kg, maximum load weight: 30,250 kg, overall weight: 35,000 kg, axle configuration: 2 axles, loading space length: 7,200 mm, loading space width: 2,350 mm, loading space height: 1,450 mm, loading space volume: 25 m³, total length: 8,600 mm, total width: 2,550 mm, total height: 3,000 mm, suspension: air, tire size: 385/65 R 22.5, tire condition: 100 %, Custom-made transport solution Configure your Fliegl vehicle according to your requirements. The vehicle shown is an example. Production and equipment are tailored to individual customer requirements. More information Chassis, semi-trailer, tipper Fine-grained steel welded construction, in basic lightweight design, turntable with interchangeable 2 kingpin Curved front end, patented 24 tons, 2-speed landing gear, single-side operation, with straight lower part, without thrust compensation Underrun protection, foldable Half-shell mudguards Towing hook at the rear Axles + suspension SAF disc brake axles with 430 mm disc diameter Axle/suspension laser-aligned to reduce tire wear and fuel consumption Axles in off-road design Air suspension 1st axle, automatic lift axle, including forced lowering and starting aid Hot-dip galvanized lift axle mechanism, 10-year warranty against rust-through Braking system Bwodpfei Ri Nfex Acfep 2-line compressed air braking system, color-coded lines for easy servicing Spring-loaded parking brake 2 fail-safe coupling heads at the front, without connection line EBS, electronic braking system with EBS socket at the front, without connection cable Note: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! With lifting and lowering valve Vehicle - driving stability system Wheels and tires 385/65 R22.5 Steel rims, factory silver "TPMS" tire pressure monitoring system according to ECE R 141, display via the display in the towing vehicle, via EBS, without truck installation (this must be available in the truck. Only for basic tires). Electrical system 24 volts, multi-chamber lights, yellow LED lighting on the side Yellow LED lighting on the side coupled with the turn signal "Flashing side lights" 2 white position lights at the front 2 white/red marker lights at the rear 2 x 7-pole fail-safe sockets at the front, without connection cable Hydraulics Low-pressure cylinder, max. 170 bar, smallest stage hard-chromed, with HDK screw connection, fixed part, NW 48 mm (without hose connection) Operation hydraulically via truck auxiliary drive Body Steel round body in Stone Master design made of highly wear-resistant HB 400/450 steel. Sloping front wall with externally mounted hydraulic cylinder with ladder on the front wall. Greenline - conical and aerodynamic body shape Shovel and broom holder on the outside of the front wall. Membrane - rear wall Rear wall as a swing gate with double hinge, externally mounted with double hook locking. 2 clamping screws with lever locks on the side below. Side walls continuous, 4 mm thick, floor 4/5 mm thick, wear-resistant and weight-optimized construction Standing platform with ladder, connection plate for air/electricity and brake with large space for best possible operation. Roll cover on one side for stowing on the right, with central locking on the left Country of registration/signs Germany With Dekra approval and certificate (according to §13 EG - FGV) Superstructure strength according to EN 12642 24/7 service hotline Prepared for license plate holder, single row Contour marking with reflective tape according to ECE R 048, white on the side and red at the rear Paint finish Frame DB 7350 Novagrau 10-year warranty against rust-through Support feet, black coated Body RAL, single color Roll cover RAL, single color Available in thermally insulated design!

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 4,900 kg, maximum load weight: 30,100 kg, overall weight: 35,000 kg, axle configuration: 3 axles, loading space length: 7,200 mm, loading space width: 2,420 mm, loading space height: 1,750 mm, loading space volume: 30 m³, total length: 8,600 mm, total width: 2,550 mm, total height: 3,230 mm, suspension: air, tire size: 385/65R22,5², tire condition: 100 %, Customized transport solution Configure according to your requirements. The vehicle shown is an example. Production and equipment are customized according to customer requirements. Further information Chassis Fine-grained steel welded construction, lightweight design, kingpin plate with 2 interchangeable kingpins Curved front end, patented Telescopic support in the center, cannot be uncoupled while loaded, when uncoupled, the vehicle must be tilted backwards. 2 support wedges with holder Underrun protection, foldable Half-shell fenders Integrated fender holder, surface designed to deflect stones With anti-spray flaps, only on the last axle Bjdpfx Aei Ri H Iecfowp 1 tarpaulin rod with holder 2 towing hooks at the rear Axles + Suspension SAF disc brake axles with 430 mm disc diameter Axle/chassis laser-measured to reduce tire wear and fuel consumption Axles in off-road design Air suspension 1st axle: automatic lift axle, including forced lowering & start assist, activated 3 times by the brakes (start assist functional up to an axle load exceeding 30% and a speed of max. 25 km/h) Hot-dip galvanized lift axle mechanism, 10-year warranty against rust-through Braking system 2-line compressed air, color-coded lines for easy servicing Spring-loaded parking brake 2 fail-safe coupling heads at the front, without connecting line EBS, electronic braking system with EBS socket at the front, without connecting cable Note: The trailer may only be towed by towing vehicles that guarantee the effectiveness of ABS! With lifting and lowering valve Vehicle stability system Automatic tilting lowering + shut-off valve Wheels + Tires 385/65R22.5, manufacturer's choice Steel rims, factory silver Electrical system 24 Volt, multi-chamber lights, yellow LED lighting on the sides 2 white position lights at the front 2 white/red marker lights at the rear 2 x 7-pole fail-safe sockets at the front, without connecting cable Hydraulics Low-pressure cylinder max. 170 bar, smallest stage hard-chromed, with HDK screw collar, fixed part, NW 48 mm. Actuation hydraulically via truck auxiliary drive Tippers Aluminum box tipper made of high-quality, abrasion-resistant material, front panel 5 mm thick, with external side panels made of 30 mm hollow section profiles, cleanly welded, with upper profile designed to prevent spillage. Inside with access ladder on the front panel. Shovel and broom holder on the outside of the front panel. Greenline - conical and aerodynamic tipper body design Membrane - rear wall Rear wall as a swing gate with double-hinge hinge, mounted externally with a double hook lock. Rear wall with rubber seal. Note! Heat-resistant up to max. 170°C! Floor continuously 6 mm thick Standing platform with access ladder, connection plate for air/electricity and brake with plenty of space for the best possible operation. Roller cover on one side for stowing on the right, with central locking on the left Operating instructions For transporting salt, lime, etc., we recommend a tipping cylinder with a hard-chromed piston rod to protect against rust. The stated total weight is technically possible; depending on the load, the total weight may not be reached while observing the permissible axle/support and kingpin loads. (Poor driving and tracking behavior possible due to incorrect load distribution) Country of registration / Signs Germany Type approval according to EC 2007/46 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective tape according to ECE

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 1,900 kg, maximum load weight: 18,100 kg, overall weight: 20,000 kg, axle configuration: 1 axle, total length: 7,650 mm, total width: 2,550 mm, tire size: 385/65 R22,5", tire condition: 100 %, Customized Transport Solution Configure your Fliegl vehicle to meet your specific requirements. The vehicle shown is an example. Production and equipment are customized according to customer specifications. *Semi-Trailer Container Chassis Fine-grained steel welded construction, semi-trailer plate with replaceable 2 kingpins, 2 pairs of removable guide rollers 4 container locks with sturdy arms based on a 20-standard for 7.45- and 7.82-swap bodies 24-metric-ton, 2-speed support jack, single-side operation, with straight lower section, without thrust compensation 2 wheel chocks with holders Aluminum side impact protection Galvanized steel underrun protection Half-shell fenders with anti-splash flaps *Axle + Suspension Disc brake axle, with 430 mm disc diameter, Air suspension with lift & lower valve, with hold function for lift & lower *Wheels and Tires 385/65 R 22.5 Steel rims, factory silver *Braking system 2-line compressed air braking system Spring-loaded parking brake 2 reverse-proof coupling heads at the front, without connecting line EBS, Electronic Braking System with EBS socket at the front, without connecting cable Caution: The trailer may only be towed by towing vehicles that ensure the effectiveness of the ABS! Bwedoi Rixnepfx Acfep *Electrical System 24 volts, multi-chamber lights, yellow LED side lighting 2 white front position lights 2 white/red rear lane-keeping lights 2 x 7-pin reverse-proof sockets in the front, without connecting cables *Registration / Plates Country of registration: Germany With DEKRA inspection and certification (per §13 EG - FGV) Prepared for single-line license plate holder Contour marking with reflective strips per ECE R 048, white on the sides and red at the rear Warning sign per ECE - 70 *Paint Finish Frame: Hot-dip galvanized or painted per customer request Support feet: Black coated